Quantic X-Microwave

Analog Devices RF and microwave components are available as drop-in X-MWblocks®
from Quantic™ X-Microwave.

Get the X-MWblock® drop-in module for this part.

ADF4360-9

PRODUCTION

Clock Generator PLL with Integrated VCO

Data Sheet (Rev. D) Product Selection Table
Viewing:

Overview

  • Primary output frequency range: 65 MHz to 400 MHz
  • Auxiliary divider from 2 to 31, output from 1.1 MHz to 200 MHz
  • 3.0 V to 3.6 V power supply
  • 1.8 V logic compatibility
  • Integer-N synthesizer
  • Programmable output power level
  • 3-wire serial interface
  • Digital lock detect
  • Software power-down mode

The ADF4360-9 is an integrated integer-N synthesizer and voltage controlled oscillator (VCO). The ADF4360-9 center frequency is set by external inductors. This allows a VCO frequency range of between 65 MHz and 400 MHz.

An additional divider stage allows division of the VCO signal. The CMOS level output is equivalent to the VCO signal divided by integer value between 2 and 31. This divided signal can be further divided by two if desired.

Control of all the on-chip registers is through a simple 3-wire interface. The device operates with a power supply ranging from 3.0 V to 3.6 V and can be powered down when not in use.

Applications

  • System clock generation
  • Test equipment
  • Wireless LANs
  • CATV equipment

    • Data Sheet, Rev. A, 3/08

    ADF4360-9
    Clock Generator PLL with Integrated VCO
    ADF4360-9 Functional Block Diagram ADF4360-9 Pin Configuration
    Add to myAnalog

    Add product to the Products section of myAnalog (to receive notifications), to an existing project or to a new project.

    Create New Project
    Ask a Question

    Documentation

    Data Sheet 1

    User Guide 2

    Frequently Asked Question 1

    Learn More
    Add to myAnalog

    Add media to the Resources section of myAnalog, to an existing project or to a new project.

    Create New Project

    Software Resources

    Device Drivers 2

    Hardware Ecosystem

    Parts Product Life Cycle Description
    Comparators 1
    LTC6957
    		Low Phase Noise, Dual Output Buffer/Driver/Logic Converter
    Frequency Dividers & Multipliers 1
    ADF5001
    		PRODUCTION 4 GHz TO 18 GHz Divide-by-4 Prescaler
    LDO Linear Regulators 3
    ADP3334
    		NOT RECOMMENDED FOR NEW DESIGNS High Accuracy Low IQ, 500 mA anyCAP­® Adjustable Low Dropout Regulator
    ADP151
    		PRODUCTION Ultralow Noise, 200 mA, CMOS Linear Regulator
    ADP150
    		PRODUCTION Ultralow Noise, 150 mA CMOS Linear Regulator
    Modulators & Demodulators 2
    ADL5375
    		PRODUCTION 400 MHz TO 6 GHz Broadband Quadrature Modulator
    ADL5380
    		RECOMMENDED FOR NEW DESIGNS 400 MHz TO 6000 MHz Quadrature Demodulator
    Operational Amplifiers (Op Amps) 1
    OP184
    		PRODUCTION Single-Supply Rail-to-Rail Input/Output Operational Amplifier
    Phase-Locked Loop (PLL) Synthesizers 1
    ADF4002
    		RECOMMENDED FOR NEW DESIGNS Phase Detector / PLL Frequency Synthesizer
    RF Mixers 2
    ADL5801
    		RECOMMENDED FOR NEW DESIGNS High IP3, 10 MHz TO 6 GHz, Active Mixer
    ADL5802
    		RECOMMENDED FOR NEW DESIGNS Dual Channel High IP3 100 MHz TO 6 GHz Active Mixer
    Switching Regulators & Controllers 1
    ADP1613
    		PRODUCTION 650 kHz /1.3 MHz Step-Up PWM DC-to-DC Switching Converter with 2.0 A Current Limit
    Modal heading
    Add to myAnalog

    Add product to the Products section of myAnalog (to receive notifications), to an existing project or to a new project.

    Create New Project

    Tools & Simulations

    ADIsimRF

    ADIsimRF is an easy-to-use RF signal chain calculator. Cascaded gain, noise, distortion and power consumption can be calculated, plotted and exported for signal chains with up to 50 stages. ADIsimRF also includes an extensive data base of device models for ADI’s RF and mixed signal components.

    Open Tool

    ADIsimPLL™

    ADIsimPLL enables the rapid and reliable evaluation of new high performance PLL products from ADI. It is the most comprehensive PLL Synthesizer design and simulation tool available today. Simulations performed include all key non-linear effects that are significant in affecting PLL performance. ADIsimPLL removes at least one iteration from the design process, thereby speeding the design- to-market.

    Open Tool

    Evaluation Kits

    eval board
    schematic 1
    schematic 2
    schematic 3
    EVAL-ADF4360-9

    ADF4360-9 Evaluation Board

    Buy Now View Details

    Features and Benefits

    • Self-contained board for generating RF frequencies
    • Flexibility for reference input, PFD frequency, and loop bandwidth
    • Accompanying software allows complete control of synthesizer functions from a PC
    • Flexibility for changing external inductor to allow different
    • VCO output frequency ranges
    • USB-/battery-operated 9 V supplies
    • Typical DIVOUT jitter performance of 1.4 ps

    Product Details

    The EV-ADF4360-9EB1Z board is designed to allow the user to evaluate the performance of the ADF4360-9 frequency synthesizer consisting of an integrated PLL and VCO. It contains the ADF4360-9BCPZ, a USB connector, and SMA connectors for the RF outputs. Unpopulated SMA footprints are available for the power supplies, lock detect, and the external reference input. The evaluation board also contains the loop filter to complete the PLL. It can be modified as necessary for the user’s PLL requirements. A USB cable is included with the board to allow software programmability. 

     

    The package also contains a CD with Windows® software to allow quick, user-friendly programming of the synthesizer. The CD contains numerous other PLL data sheets, technical notes, articles, and ADIsimPLL™ V3.4, Analog Devices, Inc., PLL simulation software. More information is available at www.analog.com/pll.
    EVAL-ADF4360-9
    ADF4360-9 Evaluation Board
    ADF4360-8/ADF4360-9 Evaluation Board ADF4360-8/ADF4360-9 Evaluation Board - Top View ADF4360-8/ADF4360-9 Evaluation Board - Bottom View

    Latest Discussions

    No discussions on ADF4360-9 yet. Have something to say?

    Start a Discussion on EngineerZone®

    Recently Viewed