MAX2754

PRODUCTION

1.2GHz VCO with Linear Modulation Input

Data Sheet (Rev. 2) Product Selection Table
Viewing:

Overview

  • Fully Monolithic VCO Construction with On-Chip Inductor and Varactor Tuning Elements
  • Guaranteed 1145MHz to 1250MHz Tuning Range to Support 1/2 LO Applications
  • Modulation Linearity Within ±4%
  • Precise Modulation Gain (-500kHz/V)
  • Low Phase Noise (-137dBc/Hz at 4MHz offset)
  • +2.7V to +5.5V Single-Supply Operation
  • Low-Current Shutdown Mode
  • Miniature 8-Pin µMAX Package

The MAX2754 self-contained, linear modulation, voltage-controlled oscillator (VCO) is intended for use in the 2.4GHz to 2.5GHz ISM band, particularly for FSK modulation systems that utilize a direct frequency-modulation transmit architecture. This device features a linear modulation input in addition to the standard frequency tuning input. The frequency tuning range of 1145MHz to 1250MHz (1/2 LO) also supports an IF up to 110MHz with low side LO. The VCO is based on Maxim's proprietary monolithic VCO technology, where all VCO components are integrated on-chip, including the varactor and inductor.

The MAX2754 linear modulation input offers a means to directly FM modulate the VCO with a constant modulation sensitivity over the tuning voltage input range. Typical frequency deviation is -500kHz/V which is linear to ±4% over the guaranteed frequency limits. The tuning input voltage range is +0.4V to +2.4V and the oscillator frequency is factory adjusted to provide guaranteed limits. The oscillator signal is buffered by an output amplifier stage (internally matched to 50Ω) to provide higher output power and isolate the oscillator from load impedance variations.

The MAX2754 operates over a +2.7V to +5.5V supply range. This device also provides a digitally controlled shutdown mode to permit implementation of sophisticated power-supply management. In shutdown, the supply current is reduced to 0.2µA. Even when active, power consumption is a modest 41mW.

The MAX2754 is packaged in the miniature 8-pin µMAX® to offer the world's smallest, complete 2.4GHz direct-modulation VCO solution.

Applications

  • 2.4GHz Cordless Phones
  • 2.4GHz Wireless Data Radios
  • Bluetooth®
  • HomeRF WLAN
MAX2754
1.2GHz VCO with Linear Modulation Input
MAX2754: Typical Operating Circuit
Add to myAnalog

Add product to the Products section of myAnalog (to receive notifications), to an existing project or to a new project.

Create New Project
Ask a Question

Documentation

Data Sheet 1

Reliability Data 1

Application Note 1

Technical Articles 3

Learn More
Add to myAnalog

Add media to the Resources section of myAnalog, to an existing project or to a new project.

Create New Project

Software Resources

Can't find the software or driver you need?

Request a Driver/Software

Evaluation Kits

MAX2754EVKIT

Evaluation Kit for the MAX2754

Buy Now View Details

Features and Benefits

  • Easy Evaluation of MAX2754
  • +2.7V to +5.5V Single-Supply Operation
  • RF Output Matched to 50Ω
  • All Critical Peripheral Components Included

Product Details

The MAX2754 evaluation kit (EV kit) simplifies evaluation of the MAX2754 VCO. This kit enables testing of the device’s RF performance and requires no additional support circuitry. The signal output uses an SMA connector to facilitate the connection to RF test equipment.

Applications

  • 2.4GHz Cordless Phones
  • 2.4GHz Wireless Data Radios
  • Bluetooth®
  • HomeRF WLAN
MAX2754EVKIT
Evaluation Kit for the MAX2754

Latest Discussions

No discussions on MAX2754 yet. Have something to say?

Start a Discussion on EngineerZone®

Recently Viewed