MAX745

PRODUCTION

Switch-Mode Lithium-Ion Battery-Charger

±0.75% Precision Li+ Charger Delivers 4A Without Heating

Viewing:

Overview

  • Charges 1 to 4 Li+ Battery Cells
  • ±0.75% Voltage-Regulation Accuracy Using 1% Resistors
  • Provides up to 4A without Excessive Heating
  • 90% Efficient
  • Uses Low-Cost Set Resistors and N-Channel Switch
  • Up to 24V Input
  • Up to 18V Maximum Battery Voltage
  • 300kHz Pulse-Width Modulated (PWM) Operation
    • Low-Noise, Small Components
  • Stand-Alone Operation—No Microcontroller Needed

The MAX745 provides all functions necessary for charging lithium-ion (Li+) battery packs. It provides a regulated charging current of up to 4A without getting hot, and a regulated voltage with only ±0.75% total error at the battery terminals. It uses low-cost, 1% resistors to set the output voltage, and a low-cost N-channel MOSFET as the power switch.

The MAX745 regulates the voltage set point and charging current using two loops that work together to transition smoothly between voltage and current regulation. The per-cell battery voltage regulation limit is set between 4V and 4.4V using standard 1% resistors, and then the number of cells is set from 1 to 4 by pin-strapping. Total output voltage error is less than ±0.75%.

For a similar device with an SMBus™ microcontroller interface and the ability to charge NiCd and NiMH cells, refer to the MAX1647 and MAX1648. For a low-cost Li+ charger using a linear-regulator control scheme, refer to the MAX846A.

Applications

  • Cell Phones
  • Desktop Cradle Chargers
  • Handheld Instruments (PDAs, Palmtops)
  • Li+ Battery Packs
  • Notebook Computers

MAX745
Switch-Mode Lithium-Ion Battery-Charger
MAX745: Typical Operating Circuit
Add to myAnalog

Add product to the Products section of myAnalog (to receive notifications), to an existing project or to a new project.

Create New Project
Ask a Question

Documentation

Learn More
Add to myAnalog

Add media to the Resources section of myAnalog, to an existing project or to a new project.

Create New Project

Software Resources

Can't find the software or driver you need?

Request a Driver/Software

Hardware Ecosystem

Parts Product Life Cycle Description
Battery Charger ICs 3
MAX846A PRODUCTION Cost-Saving, Multichemistry, Battery Charger System
MAX1640 PRODUCTION Adjustable-Output, Switch-Mode Current Sources with Synchronous Rectifier
MAX1647 PRODUCTION Chemistry-Independent Battery Chargers
Microcontrollers 1
MAX1782 Advanced Smart Battery-Pack Controller
Modal heading
Add to myAnalog

Add product to the Products section of myAnalog (to receive notifications), to an existing project or to a new project.

Create New Project

Evaluation Kits

MAX745EVKIT

Evaluation Kit for the MAX745

Features and Benefits

  • Charges One to Four Li-Ion Cells
  • Low Heat/High Efficiency
  • 300kHz PWM Operation
  • 0.75% Overall Accuracy over Temperature
  • 6V to 24V Input Voltage Range
  • Proven PC Board Layout
  • Fully Assembled and Tested

Product Details

The MAX745 evaluation kit (EV kit) is an assembled and tested PC board that implements a step-down, switching power supply designed for charging lithium-ion (Li- Ion) batteries. The output voltage can be set for one to four cells. The cell voltage can be set between 4.0V and 4.4V, with 0.75% accuracy, using standard 1% resistors. Two LEDs indicate the charging status.

The MAX745 should be used to charge only Li-Ion battery packs. To charge other types of batteries, use the MAX1648 or the MAX712/MAX713. To charge SMBus™ smart-battery packs, use the MAX1645/MAX1647/ MAX1667.

Applications

  • Cell Phones
  • Desktop Cradle Chargers
  • Handheld Instruments (PDAs, Palmtops)
  • Li+ Battery Packs
  • Notebook Computers

MAX745EVKIT
Evaluation Kit for the MAX745

Latest Discussions

Recently Viewed