ADL5511

DC to 6 GHz ENVELOPE AND TruPwr™ RMS Detector
Manufactured by:

Product Details

The ADL5511 is an RF envelope and TruPwr™ rms detector. The envelope output voltage is presented as a voltage that is proportional to the envelope of the input signal. The rms output voltage is independent of the peak-to-average ratio of the input signal.

The rms output is a linear-in-V/V voltage with a conversion gain of 1.9 V/V rms at 900 MHz. The envelope output has a conversion gain of 1.46 V/V at 900 MHz and is referenced to an internal 1.1 V reference voltage, which is available on the EREF pin.

The ADL5511 can operate from dc to 6 GHz on signals with envelope bandwidths up to 130 MHz.

The extracted envelope can be used for RF power amplifier (PA) linearization and efficiency enhancements and the rms output can be used for rms power measurement. The high rms accuracy and fast envelope response are particularly useful for envelope detection and power measurement of broadband, high peak-to-average signals that are used in CDMA2000, W-CDMA, and LTE systems.

The ADL5511 operates from −40°C to +85°C and is available in a 16-lead, 3 mm × 3 mm LFCSP package.

Applications

  • RMS power and envelope detection of W-CDMA, CDMA2000, LTE, and other complex waveforms
  • Drain modulation based power amplifier linearization
  • Power amplifier linearization employing envelope-tracking methods

Product Lifecycle

checked Recommended for New Designs

This product has been released to the market. The data sheet contains all final specifications and operating conditions. For new designs, ADI recommends utilization of these products.

Evaluation Kits

X +

Product Details

ADL5511-EVALZ is a fully populated, 4-layer, FR4-based evaluation board. For normal operation, it requires a 5 V/100 mA power supply. The 5 V power supply should be connected to the clip leads labeled VPOS and GND. The RF input signals are applied to an edge-mounted SMA type RF connector (RFIN). The envelope output signal is accessible via the SMA connector labeled VENV. The RMS output and envelope reference signals are accessible on the clip leads labeled VRMA and EREF. To access the RMS output and envelope reference output via SMA cables, SMA connectors can be soldered on to the pads labeled VRMS1 and EREF1.

Design Resources

X +

ADI has always placed the highest emphasis on delivering products that meet the maximum levels of quality and reliability. We achieve this by incorporating quality and reliability checks in every scope of product and process design, and in the manufacturing process as well.  "Zero defects" for shipped products is always our goal.

ADL5511 Material Declaration
PCN-PDN Information Quality And Reliability Symbols and Footprints

Discussions

X+

Didn't find what you were looking for?

Reviews

X+

Overview

3 Reviews
3 out of 3 (100%) customers recommend this product.
Quality
1
2
3
4
5
Reliability
1
2
3
4
5
Features
1
2
3
4
5

Most Helpful Review

by Anonymous
For the evaluation boards it would be very convenient to use discrete components no smaller the 0603 on the parts which would normally be selected or changed in the evaluation process. ( For the ADL5511 board that would be the filter caps, input cap, and resistor ) Us older engineers, in smaller companies that don't have pretty young ladies doing our assembly and rework, have a tough time seeing 0402 and smaller parts let alone change them.

Most Recent Review

by An interesting design
I solved the problem of a large, I use ADL5511 envelope detection in the project were solved and power to detect the exact problem.

All Reviews

by An interesting design, 8 Jan 15
ADL5511
I solved the problem of a large, I use ADL5511 envelope detection in the project were solved and power to detect the exact problem.
Was this Helpful?Helpful(0)
by linac.eng, 19 Feb 14
ADL5511
Great band with for multipurpas applicaties , a lot of info at the site AD for app.
Was this Helpful?Helpful(0)
by Anonymous, 3 Dec 12
Excellent part & evaluation board. Plug it in, add power & signal, & go play with it..
For the evaluation boards it would be very convenient to use discrete components no smaller the 0603 on the parts which would normally be selected or changed in the evaluation process. ( For the ADL5511 board that would be the filter caps, input cap, and resistor ) Us older engineers, in smaller companies that don't have pretty young ladies doing our assembly and rework, have a tough time seeing 0402 and smaller parts let alone change them.
Was this Helpful?Helpful(3)

Sample & Buy

X+
Back
Check Inventory

The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Analog Devices, Inc. sales office or authorized distributor. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing.


Price Table Help

 
Evaluation Boards Pricing displayed is based on 1-piece.
Pricing displayed is based on 1-piece. The USA list pricing shown is for budgetary use only, shown in United States dollars (FOB USA per unit), and is subject to change. International prices may vary due to local duties, taxes, fees and exchange rates.