The ADM2482E/ADM2487E are isolated data transceivers with ±15 kV ESD protection and are suitable for high speed, half-duplex or full-duplex communication on multipoint transmission lines. For half-duplex operation, the transmitter outputs and receiver inputs share the same transmission line. Transmitter Output Pin Y is linked externally to Receiver Input Pin A, and Transmitter Output Pin Z to Receiver Input Pin B. The parts are designed for balanced transmission lines and comply with TIA/EIA- 485-A-98 and ISO 8482:1987(E). The devices employ the Analog Devices, Inc., iCoupler® technology to combine a 3-channel isolator, a three-state differential line driver, and a differential input receiver into a single package. An on-chip oscillator outputs a pair of square waveforms that drive an external transformer to provide isolated power. The logic side of the device can be powered with either a 5 V or a 3.3 V supply, and the bus side is powered with an isolated 3.3 V supply.
The ADM2482E/ADM2487E driver has an active high enable, and the receiver has an active low enable. The driver output enters a high impedance state when the driver enable signal is low. The receiver output enters a high impedance state when the receiver enable signal is high.
The device has current-limiting and thermal shutdown features to protect against output short circuits and situations where bus contention might cause excessive power dissipation. The part is fully specified over the industrial temperature range of −40°C to +85°C and is available in a 16-lead, wide-body SOIC package.
Data Sheet, Rev. A, 3/09
|Title||Content Type||File Type|
|ADM2482E/ADM2487E: 2.5 kV Isolated RS-485 Transceivers with Integrated Transformer Driver Data Sheet (Rev A, 02/2009) (pdf, 709 kB)||Data Sheets|
|AN-960: RS-485/RS-422 Circuit Implementation Guide (pdf, 245 kB)||Application Notes|
Solving Isolation Challenges in Power Conversion Applications
This webcast will present solutions to isolation challenges in power conversion applications. Among the topics to be discussed are the limitations of traditional methods of isolation (such as utilization of optocouplers and pulse transformers) vs. more efficient and cost effective solutions that utilize digital isolators. If you are currently using optocouplers and pulse transformers, this is a webcast you should attend.
Solving Isolation Challenges in Industrial Automation
This webcast will discuss the role isolation plays in providing protection and reducing the system bit-error-rate, using the specific design challenges of an RS-485 network. Topics to be covered in this presentation will include: Why and when one should isolate, Types of isolation and their advantages, Design Considerations for an RS-485 node (and how this translates to design considerations for signal isolation) as well as many other topics.
|UG-210: Evaluation Boards for the ADM2482E and ADM2487E Isolated RS-485 Transceivers (pdf, 299 kB)||User Guides|
High-Performance Multichannel Power-Line Monitoring with Simultaneous-Sampling ADCs
By Colm Slattery, Analog Devices, Inc. (Analog Dialogue, Vol. 41, January 2007)
|MS-2155: Options and Solutions for Partitioning Isolated Power in Isolated RS-485 Nodes (pdf, 290 kB)||Technical Articles|
|MS-2127: Designing with iCoupler Digital Isolators in Solar PV Inverters (pdf, 141 kB)||Technical Articles|
Inside iCoupler® Technology:ADuM347x PWM Controller and Transformer Driver with Quad-Channel Isolators Design Summary
(pdf, 291 kB)
By Flow Zhao, Design Engineer
NAppkin Note: Lowering the Power of the ADuM524x
(pdf, 223 kB)
By Mark Cantrell, Senior Applications Engineer
|Digital Isolator Product Selection and Resource Guide (pdf, 640 kB)||Product Selection Guide|
|Analog Devices Achieves Major Milestone by Shipping 1 Billionth Channel of iCoupler Digital Isolation (19 Sep 2013)||Press Releases||HTML|
|Brochure: Motor and Power Control Solutions (pdf)||Overview|
2008 Medical Solution Profile
(pdf, 126 kB)
High Performance ICs for Medical Imaging, Patient Monitoring, and Instrumentation
|Industrial Automation Solutions (pdf, 6110 kB)||Overview|
|Emerging Energy Applications Solutions Bulletin, Volume 10, Issue 4 (pdf, 1496 kB)||Solutions Bulletins|
|Test & Instrumentation Solutions Bulletin, Volume 10, Issue 3 (pdf, 1334 kB)||Solutions Bulletins|
|How do I learn about new iCoupler products?||FAQs/RAQs||HTML|
|Are iCoupler products Pb-free?||FAQs/RAQs||HTML|
|Can I replace an optocoupler with an iCoupler product in an existing design?||FAQs/RAQs||HTML|
|What are some of the distinguishing features of the iCoupler products?||FAQs/RAQs||HTML|
|What communications protocols are supported by iCoupler products?||FAQs/RAQs||HTML|
|What are the different types of iCoupler products?||FAQs/RAQs||HTML|
|Do iCoupler products have VDE certification for reinforced insulation?||FAQs/RAQs||HTML|
|With which regulatory standards do iCoupler products comply?||FAQs/RAQs||HTML|
|How much isolation can iCoupler products provide?||FAQs/RAQs||HTML|
|What are the benefits of iCoupler technology?||FAQs/RAQs||HTML|
|What is iCoupler technology?||FAQs/RAQs||HTML|
|What types of technologies have been used to provide isolation?||FAQs/RAQs||HTML|
|What are optocouplers? What is optical isolation?||FAQs/RAQs||HTML|
|What is capacitive isolation?||FAQs/RAQs||HTML|
|What regulatory standards address isolation products?||FAQs/RAQs||HTML|
|What is isolation? Why is it needed?||FAQs/RAQs||HTML|
|What are common applications that use isolation?||FAQs/RAQs||HTML|
|How is isolation specified?||FAQs/RAQs||HTML|
|What is isolation rating?||FAQs/RAQs||HTML|
|What is the relationship between working voltage and isolation rating?||FAQs/RAQs||HTML|
|What is the difference between basic and double (or reinforced) insulation levels?||FAQs/RAQs||HTML|
|What are transient immunity and common-mode rejection?||FAQs/RAQs||HTML|
|What other parameters are important when considering an isolation device?||FAQs/RAQs||HTML|
|RAQs index||Rarely Asked Questions||HTML|
|Glossary of EE Terms||Glossary||HTML|
The ezLINX™ iCoupler® Isolated Interface Development Environment provides developers with a cost-effective, plug and play method for evaluation eight physical layer, digitally-isolated communication standards.
Evaluation board for evaluating the ADM2487E 2.5 kV Signal Isolated, ESD Protected, Full/Half Duplex RS-485 Transceiver w/ Transformer Driver (500 kbps)
Symbols and Footprints— Analog Devices offers Symbols & Footprints which are compatible with a large set of today’s CAD systems for broader and easier support.
The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Analog Devices, Inc. sales office or authorized distributor. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing.