Обзор
Особенности и преимущества
- Integrated fully differential ADC driver with signal scaling
- Wide input common-mode voltage range
- High common-mode rejection
- Single-ended to differential conversion
- Pin selectable input range with over-range
- Input Ranges with 4.096V REFBUF: ±10V, ±5V, ±4.096V, ±2.5V and ±1.5V
- Gain/Attenuation Options: 0.37, 0.73, 0.87, 1.38 and 2.25
- Critical passive components
- 0.005% precision matched resistor array for FDA
- 9 mm × 9 mm, 0.8 mm pitch, 100-ball BGA package
- 2.5× footprint reduction versus discrete solution
- Low power, dynamic power scaling, power-down mode
- Throughput: 15 MSPS, no pipeline delay
- INL error: ±7.5 ppm typical, ±15 ppm maximum
- (Gain = 0.73, gain = 0.87, gain = 1.38, gain = 2.25)
- SINAD: 90 dB typical at 1 kHz (gain = 0.37 and gain = 0.73)
- THD: −121 dB at 1 kHz, −112 dB at 100 kHz (gain = 0.73)
- Gain error: ±0.005%FS typical
- Gain error drift: ±0.11 ppm/°C typical
- On-board reference buffer with VCMO generation
- Serial LVDS interface
- Wide operating temperature range: −40°C to +85°C
Подробнее о продукте
The ADAQ23876 is a precision, high speed, μModule® data acquisition solution that reduces the development cycle of a precision measurement systems by transferring the design burden of component selection, optimization, and layout from the designer to the device.
Using System-in-Package (SIP) technology, the ADAQ23876 reduces end system component count by combining multiple common signal processing and conditioning blocks in a single device, including a low noise, fully differential ADC driver (FDA), a stable reference buffer, and a high speed, 16-bit, 15 MSPS successive approximation register (SAR) ADC.
The ADAQ23876 also incorporates the critical passive components with superior matching and drift characteristics using Analog Devices, Inc., iPassive® technology to minimize temperature dependent error sources and to offer optimized performance. The fast settling of the ADC driver stage and no latency of the SAR ADC provide a unique solution for high channel count multiplexed signal chain architectures and control loop applications.
The small footprint, 9 mm × 9 mm BGA package enables smaller form factor instruments without sacrificing performance. The system integration solves many design challenges while the device still provides the flexibility of a configurable ADC driver feedback loop to allow gain or attenuation adjustments, as well as fully differential or single-ended to differential input. A single 5 V supply operation is possible while achieving optimum performance from the device.
The ADAQ23876 features a serial LVDS digital interface with one-lane or two-lane output modes, allowing the user to optimize the interface data rate for each application. The specified operation of the μModule is from −40°C to +85°C.
APPLICATIONS
- Automatic test equipment
- Data acquisition
- Hardware in the Loop (HiL)
- Power analyzers
- Nondestructive test (acoustic emissions)
- Mass spectrometry
- Traveling wave fault location
- Medical imaging and instruments
Продукты
Области применения и технологии
Статус продукта
Рекомендовано для новых разработок
Данный продукт выпущен на рынок. Техническое описание содержит окончательные характеристики и рабочие параметры продукта. Для новых разработок ADI рекомендует применение данных продуктов.
Оценочные комплекты (1)
Техническая документация
Техническое описание (1)
Инструменты и симуляторы
LTspice
LTspice® – это мощное, быстрое и бесплатное программное обеспечение для моделирования, схемотехнического проектирования и оценки формы сигналов, содержащее усовершенствованные функции и модели, позволяющие упростить моделирование аналоговых схем.
Чтобы запустить демонстрационные схемы для этого компонента в LTspice:
Шаг 1: Загрузите и установите LTspice на ваш компьютер.
Шаг 2: Кликните по ссылке ниже для загрузки демонстрационной схемы.
Step 3: Если LTspice автоматически не открывается после нажатия на эту ссылку, вы можете запустить симуляцию, кликнув правой кнопкой мыши на ссылку и выбрать в меню "Сохранить объект как". Когда файл сохранится на вашем компьютере, запустите LTspice и откройте демонстрационную схему, выбрав пункт "Открыть" в меню "Файл".

Модели для следующих компонентов доступны в LTspice:
LTPowerPlanner
Модели IBIS
Ресурсы проектирования
Компания Analog Devices всегда уделяла повышенное внимание обеспечению максимальных уровней качества и надежности предлагаемых продуктов. Для этого мы внедряем контроль качества и надежности на каждом этапе проектирования технологических процессов и продуктов, а также на этапе производства. Нашим принципом является обеспечение "полного отсутствия дефектов" поставляемых компонентов.
Образцы и покупка
Приведенные цены действительны в США и указаны только для примерного бюджетного рассчета. Цены указаны в долларах США (за штуку в указанном размере партии) и могут быть изменены. Цены в других регионах могут отличаться в зависимости от местных пошлин, налогов, сборов и курсов валют. Для уточнения стоимости обращайтесь в местные офисы продаж Analog Devices, или к официальным дистрибьюторам. Цены на оценочные платы и наборы указаны за штуку независимо от количества.