---
type: Analog Component
title: "LTM4622 — Dual Ultrathin 2.5A or Single 5A Step-Down DC/DC µModule Regulator"
description: "Dual Ultrathin 2.5A or Single 5A Step-Down DC/DC µModule Regulator"
resource: "https://www.analog.com/en/products/ltm4622.html"
tags: ["datasheet", "linear"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ltm4622.pdf"
    title: "LTM4622 data sheet"
    author: "team:analog-devices"
tables:
  - file: "ltm4622/tables/table-00-p1-data.csv"
    title: "Product Selection Guide"
    page: 1
  - file: "ltm4622/tables/table-01-p2-abs_max.csv"
    title: "Absolute Maximum Ratings (Note 1)"
    page: 2
  - file: "ltm4622/tables/table-02-p2-data.csv"
    title: "Order Information"
    page: 2
  - file: "ltm4622/tables/table-03-p3-spec.csv"
    title: "Electrical Characteristics"
    page: 3
  - file: "ltm4622/tables/table-04-p8-spec.csv"
    title: "Decoupling Requirements"
    page: 8
  - file: "ltm4622/tables/table-05-p10-data.csv"
    title: "Table 1. V_{FB} Resistor Table vs Various Output Voltages"
    page: 10
  - file: "ltm4622/tables/table-06-p11-data.csv"
    title: "V_{OUT} / f_{SW} (MHz) / R_{FSET} (kΩ) Frequency Setting Table"
    page: 11
  - file: "ltm4622/tables/table-07-p18-data.csv"
    title: "Table 2. 1V Output"
    page: 18
  - file: "ltm4622/tables/table-08-p18-data.csv"
    title: "Table 3. 1.5V Output"
    page: 18
  - file: "ltm4622/tables/table-09-p19-data.csv"
    title: "Table 4. 2.5V Output"
    page: 19
  - file: "ltm4622/tables/table-10-p19-data.csv"
    title: "Table 5. 3.3V Output"
    page: 19
  - file: "ltm4622/tables/table-11-p19-data.csv"
    title: "Table 6. 5V Output"
    page: 19
  - file: "ltm4622/tables/table-12-p19-data.csv"
    title: "Table 7. Output Voltage Response for Each Regulator Channel vs Component Matrix (See Figure 24) 1.25A Load Step Typical Measured Values"
    page: 19
  - file: "ltm4622/tables/table-13-p24-pin.csv"
    title: "LTM4622 Component LGA and BGA Pinout"
    page: 24
  - file: "ltm4622/tables/table-16-p27-data.csv"
    title: "Revision History"
    page: 27
  - file: "ltm4622/tables/table-17-p28-data.csv"
    title: "Design Resources"
    page: 28
  - file: "ltm4622/tables/table-18-p28-data.csv"
    title: "Related Parts"
    page: 28
  - file: "ltm4622/tables/table-14-p25-data.csv"
    title: "LGA Package Dimensions Table"
    page: 25
  - file: "ltm4622/tables/table-15-p26-data.csv"
    title: "BGA Package Dimensions Table"
    page: 26
  - file: "ltm4622/tables/table-19-p7-pin.csv"
    title: "PIN FUNCTIONS"
    page: 7
figures:
  - file: "ltm4622/figures/ltm4622-f000.png"
    caption: ""
    type: "application_circuit"
    page: 1
  - file: "ltm4622/figures/ltm4622-f001.png"
    caption: "1.5V Output Efficiency vs Load Current"
    type: "characteristic_curve"
    page: 1
  - file: "ltm4622/figures/ltm4622-f002.png"
    caption: ""
    type: "pinout"
    page: 2
  - file: "ltm4622/figures/ltm4622-f003.png"
    caption: ""
    type: "pinout"
    page: 2
  - file: "ltm4622/figures/ltm4622-f005.png"
    caption: "3.3V Output Transient Response"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f006.png"
    caption: "Start-Up with 2.5A Load Current Applied"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f007.png"
    caption: "Recover from Short-Circuit with No Load Current Applied"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f008.png"
    caption: "5V Output Transient Response"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f009.png"
    caption: "Short-Circuit with No Load Current Applied"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f010.png"
    caption: "Steady-State Output Voltage Ripple"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f011.png"
    caption: "Start-Up with No Load Current Applied"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f012.png"
    caption: "Short-Circuit with 2.5A Load Current Applied"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f013.png"
    caption: "Start-Up into Pre-Biased Output"
    type: "scope_capture"
    page: 6
  - file: "ltm4622/figures/ltm4622-f014.png"
    caption: ""
    type: "other"
    page: 7
  - file: "ltm4622/figures/ltm4622-f015.png"
    caption: "Figure 1. Simplified LTM4622 Block Diagram"
    type: "block_diagram"
    page: 8
  - file: "ltm4622/figures/ltm4622-f016.png"
    caption: "Figure 2. Example of Clock Phasing for 4-Phase Operation with LTC6902"
    type: "application_circuit"
    page: 12
  - file: "ltm4622/figures/ltm4622-f017.png"
    caption: "Figure 3. Input RMS Current Ratios to DC Load Current as a Function of Duty Cycle"
    type: "characteristic_curve"
    page: 12
  - file: "ltm4622/figures/ltm4622-f018.png"
    caption: "Figure 4. Output Ratiometric T racking Waveform"
    type: "timing_diagram"
    page: 13
  - file: "ltm4622/figures/ltm4622-f019.png"
    caption: "Figure 5. Example Schematic of Ratiometric Output Voltage T racking"
    type: "application_circuit"
    page: 13
  - file: "ltm4622/figures/ltm4622-f020.png"
    caption: "Figure 6. Output Coincident T racking Waveform"
    type: "timing_diagram"
    page: 13
  - file: "ltm4622/figures/ltm4622-f021.png"
    caption: "Figure 7. Graphical Representation of JESD 51-12 Thermal Coefficients"
    type: "block_diagram"
    page: 15
  - file: "ltm4622/figures/ltm4622-f022.png"
    caption: "Figure 8. 1V Output Power Loss"
    type: "characteristic_curve"
    page: 17
  - file: "ltm4622/figures/ltm4622-f023.png"
    caption: "Figure 11. 3.3V Output Power Loss"
    type: "characteristic_curve"
    page: 17
  - file: "ltm4622/figures/ltm4622-f024.png"
    caption: "Figure 14. 12V to 1V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 17
  - file: "ltm4622/figures/ltm4622-f025.png"
    caption: "Figure 9. 1.5V Output Power Loss"
    type: "characteristic_curve"
    page: 17
  - file: "ltm4622/figures/ltm4622-f026.png"
    caption: "Figure 12. 5V Output Power Loss"
    type: "characteristic_curve"
    page: 17
  - file: "ltm4622/figures/ltm4622-f027.png"
    caption: "Figure 15. 5V to 1.5V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 17
  - file: "ltm4622/figures/ltm4622-f028.png"
    caption: "Figure 10. 2.5V Output Power Loss"
    type: "characteristic_curve"
    page: 17
  - file: "ltm4622/figures/ltm4622-f029.png"
    caption: "Figure 13. 5V to 1V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 17
  - file: "ltm4622/figures/ltm4622-f030.png"
    caption: "Figure 16. 12V to 1.5V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 17
  - file: "ltm4622/figures/ltm4622-f031.png"
    caption: "Figure 17. 5V to 2.5V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 18
  - file: "ltm4622/figures/ltm4622-f032.png"
    caption: "Figure 18. 12V to 2.5V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 18
  - file: "ltm4622/figures/ltm4622-f033.png"
    caption: "Figure 19. 5V to 3.3V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 18
  - file: "ltm4622/figures/ltm4622-f034.png"
    caption: "Figure 20. 12V to 3.3V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 18
  - file: "ltm4622/figures/ltm4622-f035.png"
    caption: "Figure 21. 12V to 5V Derating Curve, No Heat Sink"
    type: "thermal"
    page: 18
  - file: "ltm4622/figures/ltm4622-f036.png"
    caption: "Figure 22.  Thermal Picture, 12V Input, 3.3V and 5V Output, 2.5A DC Each  Output with No Airflow and No Heat Sink"
    type: "other"
    page: 20
  - file: "ltm4622/figures/ltm4622-f037.png"
    caption: "Figure 23.  Recommended PCB Layout"
    type: "layout_drawing"
    page: 21
  - file: "ltm4622/figures/ltm4622-f038.png"
    caption: "Figure 24.  4V_{IN} to 20V_{IN} , 1V and 1.8V Output at 2.5A Design"
    type: "application_circuit"
    page: 22
  - file: "ltm4622/figures/ltm4622-f039.png"
    caption: "Figure 25. 4V_{IN} to 20V_{IN} , 1.2V T wo Phase in Parallel 5A Design"
    type: "application_circuit"
    page: 22
  - file: "ltm4622/figures/ltm4622-f040.png"
    caption: "Figure 26.  8V_{IN} to 20V_{IN} , 3.3V and 5V Output at 2.5A with 2MHz Switching Frequency"
    type: "application_circuit"
    page: 22
  - file: "ltm4622/figures/ltm4622-f041.png"
    caption: "Figure 27.  3.3V_{IN} , 1.5V and 1.2V Output at 2.5A Design with Output Coincident T racking"
    type: "application_circuit"
    page: 23
  - file: "ltm4622/figures/ltm4622-f042.png"
    caption: "Figure 28. 4 Phase, 1V Output at 10A Design with LTC6902"
    type: "application_circuit"
    page: 23
  - file: "ltm4622/figures/ltm4622-f043.png"
    caption: ""
    type: "other"
    page: 24
  - file: "ltm4622/figures/ltm4622-f045.png"
    caption: "LGA Package 25-Lead (6.25mm × 6.25mm × 1.82mm) (Reference LTC DWG # 05-08-1949 Rev Ø)"
    type: "other"
    page: 25
  - file: "ltm4622/figures/ltm4622-f046.png"
    caption: ""
    type: "other"
    page: 26
  - file: "ltm4622/figures/ltm4622-f048.png"
    caption: ""
    type: "other"
    page: 28
  - file: "ltm4622/figures/ltm4622-f050.png"
    caption: ""
    type: "other"
    page: 28
  - file: "ltm4622/figures/ltm4622-f051.png"
    caption: "Efficiency vs Load Current at 5V_{IN}"
    type: "characteristic_curve"
    page: 5
  - file: "ltm4622/figures/ltm4622-f052.png"
    caption: "Efficiency vs Load Current at 12V_{IN}"
    type: "characteristic_curve"
    page: 5
  - file: "ltm4622/figures/ltm4622-f053.png"
    caption: "Efficiency vs Load Current at 3.3V_{IN}"
    type: "characteristic_curve"
    page: 5
  - file: "ltm4622/figures/ltm4622-f054.png"
    caption: "Burst Mode Efficiency, 12V_{IN}, 1.5V_{OUT}"
    type: "characteristic_curve"
    page: 5
  - file: "ltm4622/figures/ltm4622-f055.png"
    caption: "1V Output Transient Response"
    type: "other"
    page: 5
  - file: "ltm4622/figures/ltm4622-f056.png"
    caption: "1.2V Output Transient Response"
    type: "other"
    page: 5
  - file: "ltm4622/figures/ltm4622-f057.png"
    caption: "1.5V Output Transient Response"
    type: "other"
    page: 5
  - file: "ltm4622/figures/ltm4622-f058.png"
    caption: "1.8V Output Transient Response"
    type: "other"
    page: 5
  - file: "ltm4622/figures/ltm4622-f059.png"
    caption: "2.5V Output Transient Response"
    type: "other"
    page: 5
  - file: "ltm4622/figures/ltm4622-f060.png"
    caption: "Sort table of products by parameters and download the result as a spread sheet. Search using the Quick Power Search parametric table."
    type: "other"
    page: 28
  - file: "ltm4622/figures/ltm4622-eq01.png"
    caption: "Equation as printed (p. 9)"
    type: equation
    page: 9
  - file: "ltm4622/figures/ltm4622-eq02.png"
    caption: "Equation as printed (p. 9)"
    type: equation
    page: 9
  - file: "ltm4622/figures/ltm4622-eq03.png"
    caption: "Equation as printed (p. 10)"
    type: equation
    page: 10
  - file: "ltm4622/figures/ltm4622-eq04.png"
    caption: "Equation as printed (p. 10)"
    type: equation
    page: 10
  - file: "ltm4622/figures/ltm4622-eq05.png"
    caption: "Equation as printed (p. 10)"
    type: equation
    page: 10
  - file: "ltm4622/figures/ltm4622-eq06.png"
    caption: "Equation as printed (p. 11)"
    type: equation
    page: 11
  - file: "ltm4622/figures/ltm4622-eq07.png"
    caption: "Equation as printed (p. 11)"
    type: equation
    page: 11
  - file: "ltm4622/figures/ltm4622-eq08.png"
    caption: "Equation as printed (p. 11)"
    type: equation
    page: 11
  - file: "ltm4622/figures/ltm4622-eq09.png"
    caption: "Equation as printed (p. 12)"
    type: equation
    page: 12
  - file: "ltm4622/figures/ltm4622-eq10.png"
    caption: "Equation as printed (p. 13)"
    type: equation
    page: 13
  - file: "ltm4622/figures/ltm4622-eq11.png"
    caption: "Equation as printed (p. 13)"
    type: equation
    page: 13
  - file: "ltm4622/figures/ltm4622-eq12.png"
    caption: "Equation as printed (p. 14)"
    type: equation
    page: 14
curves:
  - file: "ltm4622/curves/1-5v-output-efficiency-vs-load-current.csv"
    caption: "1.5V Output Efficiency vs Load Current"
    figure: "ltm4622/figures/ltm4622-f001.png"
    page: 1
    x_unit: "A"
    y_unit: "%"
  - file: "ltm4622/curves/1-5v-output-power-loss.csv"
    caption: "Figure 9. 1.5V Output Power Loss"
    figure: "ltm4622/figures/ltm4622-f025.png"
    page: 17
    x_unit: "A"
    y_unit: "W"
  - file: "ltm4622/curves/12v-to-1-5v-derating-curve-no-heat-sink.csv"
    caption: "Figure 16. 12V to 1.5V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f030.png"
    page: 17
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/12v-to-1v-derating-curve-no-heat-sink.csv"
    caption: "Figure 14. 12V to 1V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f024.png"
    page: 17
  - file: "ltm4622/curves/12v-to-2-5v-derating-curve-no-heat-sink.csv"
    caption: "Figure 18. 12V to 2.5V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f032.png"
    page: 18
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/12v-to-3-3v-derating-curve-no-heat-sink.csv"
    caption: "Figure 20. 12V to 3.3V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f034.png"
    page: 18
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/12v-to-5v-derating-curve-no-heat-sink.csv"
    caption: "Figure 21. 12V to 5V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f035.png"
    page: 18
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/1v-output-power-loss.csv"
    caption: "Figure 8. 1V Output Power Loss"
    figure: "ltm4622/figures/ltm4622-f022.png"
    page: 17
    x_unit: "A"
    y_unit: "W"
  - file: "ltm4622/curves/2-5v-output-power-loss.csv"
    caption: "Figure 10. 2.5V Output Power Loss"
    figure: "ltm4622/figures/ltm4622-f028.png"
    page: 17
    x_unit: "A"
    y_unit: "W"
  - file: "ltm4622/curves/3-3v-output-power-loss.csv"
    caption: "Figure 11. 3.3V Output Power Loss"
    figure: "ltm4622/figures/ltm4622-f023.png"
    page: 17
    x_unit: "A"
    y_unit: "W"
  - file: "ltm4622/curves/5v-output-power-loss.csv"
    caption: "Figure 12. 5V Output Power Loss"
    figure: "ltm4622/figures/ltm4622-f026.png"
    page: 17
    x_unit: "A"
    y_unit: "W"
    conditions: "V_{IN} = 12V"
  - file: "ltm4622/curves/5v-to-1-5v-derating-curve-no-heat-sink.csv"
    caption: "Figure 15. 5V to 1.5V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f027.png"
    page: 17
    x_unit: "°C"
    y_unit: ""
  - file: "ltm4622/curves/5v-to-1v-derating-curve-no-heat-sink.csv"
    caption: "Figure 13. 5V to 1V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f029.png"
    page: 17
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/5v-to-2-5v-derating-curve-no-heat-sink.csv"
    caption: "Figure 17. 5V to 2.5V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f031.png"
    page: 18
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/5v-to-3-3v-derating-curve-no-heat-sink.csv"
    caption: "Figure 19. 5V to 3.3V Derating Curve, No Heat Sink"
    figure: "ltm4622/figures/ltm4622-f033.png"
    page: 18
    x_unit: "°C"
    y_unit: "A"
  - file: "ltm4622/curves/burst-mode-efficiency-12vin-1-5vout.csv"
    caption: "Burst Mode Efficiency, 12V_{IN}, 1.5V_{OUT}"
    figure: "ltm4622/figures/ltm4622-f054.png"
    page: 5
    x_unit: "A"
    y_unit: "%"
  - file: "ltm4622/curves/input-rms-current-ratios-to-dc-load-current-as-a-function-of-duty-cycle.csv"
    caption: "Figure 3. Input RMS Current Ratios to DC Load Current as a Function of Duty Cycle"
    figure: "ltm4622/figures/ltm4622-f017.png"
    page: 12
    x_unit: "V_{OUT}/V_{IN}"
    y_unit: "ratio"
agentforge:
  part_number: "LTM4622"
  datasheet_revision: "J"
  reading_order: "structure-tree"
---

# LTM4622 — Dual Ultrathin 2.5A or Single 5A Step-Down DC/DC µModule Regulator

*Datasheet: [LTM4622 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ltm4622.pdf)*

### FEATURES

- Complete Solution in <1cm^{2}
- Wide Input Voltage Range: 3.6V to 20V
- 3.3V Input Compatible with V_{IN} Tied to INTV_{CC}
- 0.6V to 5.5V Output Voltage
- Dual 2.5A (3A Peak) or Single 5A Output Current
- ±1.5% Maximum Total Output Voltage Regulation Error Over Load, Line, and Temperature
- Current Mode Control, Fast T ransient Response
- External Frequency Synchronization
- Multiphase Parallelable with Current Sharing
- Output Voltage T racking and Soft-Start Capability
- Selectable Burst Mode®  Operation
- Overvoltage Input and Overtemperature Protection
- Power Good Indicators
- 6.25mm × 6.25mm × 1.82mm LGA and 6.25mm × 6.25mm × 2.42mm BGA Packages

### APPLICATIONS

- General Purpose Point-of-Load Conversion
- Telecom, Networking and Industrial Equipment
- Medical Diagnostic Equipment
- Test and Debug Systems

All registered trademarks and trademarks are the property of their respective owners.

### DESCRIPTION

The LTM® 4622 is a complete dual 2.5A step-down switching mode power µModule®  (power module) regulator in a tiny ultrathin 6.25mm × 6.25mm × 1.82mm LGA and 6.25mm × 6.25mm × 2.42mm BGA packages. Included in the package is the switching controller , the power FETs, the inductor , and the supporting components. Operating over an input voltage range of 3.6V to 20V, the LTM4622 supports an output voltage range of 0.6V to 5.5V, set by a single external resistor . Its high efficiency design delivers dual 2.5A continuous, 3A peak, output current. Only a few ceramic input and output capacitors are needed.

The LTM4622 supports selectable Burst Mode operation and output voltage tracking for supply rail sequencing. Its high switching frequency and current mode control enable a very fast transient response to line and load changes without sacrificing stability.

Fault protection features include input overvoltage, output  overcurrent  and  overtemperature  protection.  The LTM4622 is available with SnPb (BGA) or RoHS-compliant terminal finish.

### Product Selection Guide

**Product Selection Guide** ([table-00-p1-data.csv](ltm4622/tables/table-00-p1-data.csv), p. 1)

| PART NUMBER | V_{IN} RANGE | V_{OUT} RANGE | I_{OUT} |
|---|---|---|---|
| LTM4622 | 3.6V to 20V | 0.6V to 5.5V | Dual 2.5A or Single 5A |
| LTM4622A | 3.6V to 20V | 1.5V to 12V | Dual 2A or Single 4A |

### TYPICAL APPLICATION

### 1.5V and 1V Dual Output DC/DC Step-Down µModule Regulator

![application circuit (p. 1)](ltm4622/figures/ltm4622-f000.png)

### 1.5V Output Efficiency vs Load Current

![1.5V Output Efficiency vs Load Current](ltm4622/figures/ltm4622-f001.png)

*1.5V Output Efficiency vs Load Current*

Digitized data: [1-5v-output-efficiency-vs-load-current.csv](ltm4622/curves/1-5v-output-efficiency-vs-load-current.csv) (x: A; y: %) — values read off the printed plot by the digitizer, not published data.

### ABSOLUTE MAXIMUM RATINGS (Note 1)

**Absolute Maximum Ratings (Note 1)** ([table-01-p2-abs_max.csv](ltm4622/tables/table-01-p2-abs_max.csv), p. 2)

| PARAMETER | RATING |
|---|---|
| V_{IN1}, V_{IN2} | −0.3V to 22V |
| V_{OUT} | −0.3V to 6V |
| PGOOD1, PGOOD2 | −0.3V to 18V |
| RUN1, RUN2 | −0.3V to V_{IN} + 0.3V |
| INTV_{CC}, TRACK/SS1, TRACK/SS2 | −0.3V to 3.6V |
| SYNC/MODE, COMP1, COMP2, FB1, FB2 | −0.3V to INTV_{CC} |
| Operating Internal Temperature Range (Note 2) | −40°C to 125°C |
| Storage Temperature Range | −55°C to 125°C |
| Peak Solder Reflow Body Temperature | 260°C |

### PIN CONFIGURATION (See Pin Functions, Pin Configuration Table)

- [ LGA and BGA Package and Tray Drawings](https://www.analog.com/en/design-center/packaging-quality-symbols-footprints.html)

![pinout (p. 2)](ltm4622/figures/ltm4622-f002.png)

![pinout (p. 2)](ltm4622/figures/ltm4622-f003.png)

### ORDER INFORMATION

**Order Information** ([table-02-p2-data.csv](ltm4622/tables/table-02-p2-data.csv), p. 2)

| PART NUMBER | PAD OR BALL FINISH | DEVICE | FINISH CODE | PACKAGE TYPE | MSL RATING | TEMPERATURE RANGE (NOTE 2) |
|---|---|---|---|---|---|---|
| **PART MARKING** |  |  |  |  |  |  |
| LTM4622EV#PBF | Au (RoHS) | LTM4622V | e4 | LGA | 4 | –40°C to 125°C |
| LTM4622IV#PBF | Au (RoHS) | LTM4622V | e4 | LGA | 4 | –40°C to 125°C |
| LTM4622EY#PBF | SAC305 (RoHS) | LTM4622Y | e1 | BGA | 4 | –40°C to 125°C |
| LTM4622IY#PBF | SAC305 (RoHS) | LTM4622Y | e1 | BGA | 4 | –40°C to 125°C |
| LTM4622IY | SnPb (63/37) | LTM4622Y | e0 | BGA | 4 | –40°C to 125°C |

- Contact the factory for parts specified with wider operating temperature ranges. Pad or ball finish code is per IPC/JEDEC J-STD-609.
- Recommended LGA and BGA PCB Assembly and Manufacturing Procedures
- LGA and BGA Package and Tray Drawings

### ELECTRICAL CHARACTERISTICS

The ● denotes the specifications which apply over the full internal operating temperature range (Note 2). Specified as each individual output channel at T_{A} = 25°C, V_{IN1} = V_{IN2} = 12V, unless otherwise noted per the typical application shown in Figure 24.

**Electrical Characteristics** ([table-03-p3-spec.csv](ltm4622/tables/table-03-p3-spec.csv), p. 3)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS | OVERTEMP |
|---|---|---|---|---|---|---|---|
| **Switching Regulator Section: per Channel** |  |  |  |  |  |  |  |
| Input DC Voltage | V_{IN1} |  | 3.6 |  | 20 | V | ● |
| Input DC Voltage | V_{IN2} | 3.6V < V_{IN1} <20V | 1.5 |  | 20 | V | ● |
| 3.3V Input DC Voltage | V_{IN_3.3} | V_{IN1} = V_{IN2} = INTV_{CC} | 3.1 | 3.3 | 3.5 | V | ● |
| Output Voltage Range | V_{OUT(RANGE)} | V_{IN1} = V_{IN2} = 3.6V to 20V | 0.6 |  | 5.5 | V | ● |
| Output Voltage, Total Variation with Line and Load | V_{OUT(DC)} | C_{IN} = 22µF, C_{OUT} = 100µF Ceramic, R_{FB} = 40.2k, MODE = INTV_{CC}, V_{IN1} = V_{IN2} = 3.6V to 20V, I_{OUT} = 0A to 2.5A | 1.477 | 1.50 | 1.523 | V | ● |
| RUN Pin ON Threshold | V_{RUN} | RUN Threshold Rising | 1.20 | 1.27 | 1.35 | V |  |
| RUN Pin ON Threshold | V_{RUN} | RUN Threshold Falling | 0.97 | 1.00 | 1.03 | V |  |
| Input Supply Bias Current | I_{Q(V_{IN})} | V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V, MODE = GND |  | 11 |  | mA |  |
| Input Supply Bias Current | I_{Q(V_{IN})} | V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V, MODE = INTV_{CC} |  | 500 |  | µA |  |
| Input Supply Bias Current | I_{Q(V_{IN})} | Shutdown, RUN1 = RUN2 = 0 |  | 45 |  | µA |  |
| Input Supply Current | I_{S(V_{IN})} | V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V, I_{OUT} = 2.5A |  | 0.35 |  | A |  |
| Output Continuous Current Range | I_{OUT(DC)} | V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V (Note 3) | 0 |  | 2.5 | A | ● |
| Line Regulation Accuracy | ΔV_{OUT} (Line)/V_{OUT} | V_{OUT} = 1.5V, V_{IN1} = V_{IN2} = 3.6V to 20V, I_{OUT} = 0A |  | 0.01 | 0.1 | %/V | ● |
| Load Regulation Accuracy | ΔV_{OUT} (Load)/V_{OUT} | V_{OUT} = 1.5V, I_{OUT} = 0A to 2.5A |  | 0.2 | 1.0 | % | ● |
| Output Ripple Voltage | V_{OUT(AC)} | I_{OUT} = 0A, C_{OUT} = 100µF Ceramic, V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V |  | 5 |  | mV |  |
| Turn-On Overshoot | ΔV_{OUT(START)} | I_{OUT} = 0A, C_{OUT} = 100µF Ceramic, V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V |  | 30 |  | mV |  |
| Turn-On Time | t_{START} | C_{OUT} = 100µF Ceramic, No Load, TRACK/SS = 0.01µF, V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V |  | 5.3 |  | ms |  |
| Peak Deviation for Dynamic Load | ΔV_{OUTLS} | Load: 0% to 50% to 0% of Full Load, C_{OUT} = 100µF Ceramic, V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V |  | 100 |  | mV |  |
| Settling Time for Dynamic Load Step | t_{SETTLE} | Load: 0% to 50% to 0% of Full Load, C_{OUT} = 100µF Ceramic, V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V |  | 20 |  | µs |  |
| Output Current Limit | I_{OUTPK} | V_{IN1} = V_{IN2} = 12V, V_{OUT} = 1.5V | 3 | 4 |  | A |  |
| Voltage at FB Pin | V_{FB} | I_{OUT} = 0A, V_{OUT} = 1.5V | 0.592 | 0.60 | 0.608 | V | ● |
| Current at FB Pin | I_{FB} | (Note 4) |  |  | ±30 | nA |  |
| Resistor Between V_{OUT} and FB Pins | R_{FBHI} |  | 60.00 | 60.40 | 60.80 | kΩ |  |
| Track Pin Soft-Start Pull-Up Current | I_{TRACK/SS} | TRACK/SS = 0V |  | 1.2 |  | µA |  |
| Internal Soft-Start Time | t_{SS} | 10% to 90% Rise Time (Note 4) |  | 400 | 700 | µs |  |
| Minimum On-Time | t_{ON(MIN)} | (Note 4) |  | 20 |  | ns |  |
| Minimum Off-Time | t_{OFF(MIN)} | (Note 4) |  | 45 |  | ns |  |
| PGOOD Trip Level | V_{PGOOD} | V_{FB} with Respect to Set Output: V_{FB} Ramping Negative |  | −8 | −14 | % |  |
| PGOOD Trip Level | V_{PGOOD} | V_{FB} with Respect to Set Output: V_{FB} Ramping Positive |  | 8 | 14 | % |  |
| PGOOD Pull-Down Resistance | R_{PGOOD} | 1mA Load |  | 20 |  | Ω |  |
| Internal V_{CC} Voltage | V_{INTVCC} | V_{IN1} = V_{IN2} = 3.6V to 20V | 3.1 | 3.3 | 3.5 | V |  |
| INTV_{CC} Load Regulation | V_{INTVCC} Load Reg | I_{CC} = 0mA to 50mA |  | 1.3 |  | % |  |
| Oscillator Frequency | f_{OSC} |  |  | 1 |  | MHz |  |
| Frequency Sync Range | f_{SYNC} | With Respect to Set Frequency |  | ±30 |  | % |  |
| MODE Input Current | I_{MODE} | MODE = INTV_{CC} |  | −1.5 |  | µA |  |

- **Note 1:** Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.

- **Note 2:** The LTM4622 is tested under pulsed load conditions such that T_{J} ≈ T_{A} . The LTM4622E is guaranteed to meet performance specifications over the 0°C to 125°C internal operating temperature range. Specifications over the full -40°C to 125°C internal operating temperature range are assured by design, characterization, and correlation with statistical process controls. The LTM4622I is guaranteed to meet specifications over the full -40°C to 125°C internal operating temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance, and other environmental factors.

- **Note 3:** See the Thermal Considerations and Output Current Derating in the Applications Information section for different V_{IN} , V_{OUT} and T_{A} .

- **Note 4:** 100% tested at wafer level.

- **Note 5:** This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability.

### TYPICAL PERFORMANCE CHARACTERISTICS

![Efficiency vs Load Current at 5V_{IN}](ltm4622/figures/ltm4622-f051.png)

*Efficiency vs Load Current at 5V_{IN}*

![Efficiency vs Load Current at 12V_{IN}](ltm4622/figures/ltm4622-f052.png)

*Efficiency vs Load Current at 12V_{IN}*

![Efficiency vs Load Current at 3.3V_{IN}](ltm4622/figures/ltm4622-f053.png)

*Efficiency vs Load Current at 3.3V_{IN}*

![Burst Mode Efficiency, 12V_{IN}, 1.5V_{OUT}](ltm4622/figures/ltm4622-f054.png)

*Burst Mode Efficiency, 12V_{IN}, 1.5V_{OUT}*

Digitized data: [burst-mode-efficiency-12vin-1-5vout.csv](ltm4622/curves/burst-mode-efficiency-12vin-1-5vout.csv) (x: A; y: %) — values read off the printed plot by the digitizer, not published data.

![1V Output Transient Response](ltm4622/figures/ltm4622-f055.png)

*1V Output Transient Response*

![1.2V Output Transient Response](ltm4622/figures/ltm4622-f056.png)

*1.2V Output Transient Response*

![1.5V Output Transient Response](ltm4622/figures/ltm4622-f057.png)

*1.5V Output Transient Response*

![1.8V Output Transient Response](ltm4622/figures/ltm4622-f058.png)

*1.8V Output Transient Response*

![2.5V Output Transient Response](ltm4622/figures/ltm4622-f059.png)

*2.5V Output Transient Response*

![3.3V Output Transient Response](ltm4622/figures/ltm4622-f005.png)

*3.3V Output Transient Response*

![5V Output Transient Response](ltm4622/figures/ltm4622-f008.png)

*5V Output Transient Response*

![Start-Up with No Load Current Applied](ltm4622/figures/ltm4622-f011.png)

*Start-Up with No Load Current Applied*

![Start-Up with 2.5A Load Current Applied](ltm4622/figures/ltm4622-f006.png)

*Start-Up with 2.5A Load Current Applied*

![Short-Circuit with No Load Current Applied](ltm4622/figures/ltm4622-f009.png)

*Short-Circuit with No Load Current Applied*

![Short-Circuit with 2.5A Load Current Applied](ltm4622/figures/ltm4622-f012.png)

*Short-Circuit with 2.5A Load Current Applied*

![Recover from Short-Circuit with No Load Current Applied](ltm4622/figures/ltm4622-f007.png)

*Recover from Short-Circuit with No Load Current Applied*

![Steady-State Output Voltage Ripple](ltm4622/figures/ltm4622-f010.png)

*Steady-State Output Voltage Ripple*

![Start-Up into Pre-Biased Output](ltm4622/figures/ltm4622-f013.png)

*Start-Up into Pre-Biased Output*

### PIN FUNCTIONS

![other (p. 7)](ltm4622/figures/ltm4622-f014.png)

PACKAGE ROW AND COLUMN LABELING MAY VARY AMONG µModule PRODUCTS. REVIEW EACH PACKAGE LAYOUT CAREFULLY.

**GND (Pins C1, C2, B5, D5)**: Power Ground Pins for Both Input and Output Returns.

**INTV_{CC} (Pin C3)**: Internal 3.3V Regulator Output. The internal power drivers and control circuits are powered from this voltage. This pin is internally decoupled to GND with a 2.2µF low ESR ceramic capacitor . No additional external decoupling capacitor needed.

**FREQ (Pin C4)**: Frequency is set internally to 1MHz. An external resistor can be placed from this pin to GND to increase frequency, or from this pin to INTV_{CC} to reduce frequency. See the Applications Information section for frequency adjustment.

**SYNC/MODE  (Pin  C5)**: Mode  Select  and  External Synchronization Input. Tie this pin to ground to force continuous synchronous operation at all output loads. Floating this pin or tying it to INTV_{CC} enables high efficiency Burst Mode operation at light loads. Drive this pin with a clock to synchronize the LTM4622 switching frequency. An internal phase-locked loop will force the bottom power NMOS's turn on signal to be synchronized with the rising edge of the clock signal. When this pin is driven with a clock, forced continuous mode (FCM) is automatically selected.

**V_{OUT1}  (Pins D1, E1), V_{OUT2} (Pins A1, B1)**: Power Output Pins of Each Switching Mode Regulator . Apply output load between these pins and GND pins. Recommend placing output decoupling capacitance directly between these pins and GND pins.

**RUN1 (Pin D2), RUN2 (Pin B2)**: Run Control Input of Each Switching Mode Regulator Channel. Enables chip operation by tying RUN above 1.27V. Tying this pin below 1V shuts down the specific regulator channel. Do not float this pin.

**V_{IN1}   (Pins  D3,  E2),  V_{IN2}   (Pins  A2,  B3)**: Power Input Pins. Apply input voltage between these pins and GND pins. Recommend placing input decoupling capacitance directly between BOTH V_{IN1} and V_{IN2} pins and GND pins. Please note the  module internal control circuity is running off V_{IN1} . Channel 2 will not work without a voltage higher that 3.6V present at V_{IN1} .

**PGOOD1 (Pin D4), PGOOD2 (Pin B4)**: Output  Power Good with Open-Drain Logic of Each Switching Mode Regulator Channel. PGOOD is pulled to ground when the voltage on the FB pin is not within ±8% (typical) of the internal 0.6V reference.

**TRACK/SS1  (Pin  E3),  TRACK/SS2  (Pin  A3)**: Output Tracking  and  Soft-Start  Pin  of  Each  Switching  Mode Regulator Channel. It allows the user to control the rise time of the output voltage. Putting a voltage below 0.6V on this pin bypasses the internal reference input to the error amplifier , instead it servos the FB pin to the TRACK voltage. Above 0.6V, the tracking function stops and the internal reference resumes control of the error amplifier . There's an internal 1.2µA pull-up current from INTV_{CC} on this pin, so putting a capacitor here provides soft-start function. A default internal soft-start ramp forces a minimum soft-start time of 400µs.

**FB1  (Pin  E4),  FB2  (Pin  A4)**: The  Negative  Inpute  of the Error Amplifier for Each Switching Mode Regulator Channel. Internally, this pin is connected to V_{OUT} with a 60.4k precision resistor . Different output voltages can be programmed with an additional resistor between FB and GND pins. In PolyPhase ®  operation, tying the FB pins together allows for parallel operation. See the Applications Information section for details.

**COMP1 (Pin  E5),  COMP2  (Pin  A5)**: Current  Control Threshold and Error Amplifier Compensation Point of Each Switching Mode Regulator Channel. The current comparator's trip threshold is linearly proportional to this voltage, whose normal range is from 0.3V to 1.8V. Tie the COMP pins together for parallel operation. The device is internal compensated. Do not drive this pin.

### BLOCK DIAGRAM

![Figure 1. Simplified LTM4622 Block Diagram](ltm4622/figures/ltm4622-f015.png)

*Figure 1. Simplified LTM4622 Block Diagram*

### DECOUPLING REQUIREMENTS

**Decoupling Requirements** ([table-04-p8-spec.csv](ltm4622/tables/table-04-p8-spec.csv), p. 8)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| External Input Capacitor Requirement (V_{IN} = 3.6V to 20V, V_{OUT} = 1.5V) | C_{IN} | I_{OUT} = 2.5A | 4.7 | 10 |  | µF |
| External Output Capacitor Requirement (V_{IN} = 3.6V to 20V, V_{OUT} = 1.5V) | C_{OUT} | I_{OUT} = 2.5A | 22 | 47 |  | µF |

### OPERATION

The LTM4622 is a dual output standalone nonisolated switch mode DC/DC power supply. It can deliver two 2.5A DC, 3A peak output current with few external input and output ceramic capacitors. This module provides dual precisely  regulated  output  voltage  programmable  via two external resistor from 0.6V to 5.5V over 3.6V to 20V input voltage range. With INTV_{CC} tied to V_{IN} , this module is able to operate from 3.3V input. The typical application schematic is shown in Figure 24.

The LTM4622 contains an integrated controlled on-time valley current mode regulator , power MOSFETs, inductor , and other supporting discrete components. The default switching frequency is 1MHz. For output voltages between 2.5V and 5.5V, an external resistor is required between FREQ and GND pins to set the operating frequency to higher  frequency  to  optimize  inductor  current  ripple. For switching noise-sensitive applications, the switching frequency can be adjusted by external resistors and the µModule regulator can be externally synchronized to  a  clock  within  ±30% of the set frequency. See the Applications Information section.

With current mode control and internal feedback loop compensation,  the  LTM4622  module  has  sufficient stability margins and good transient performance with a wide range of output capacitors, even with all ceramic output capacitors.

Current mode control provides cycle-by-cycle fast current limiting. An internal overvoltage and undervoltage comparators pull the open-drain PGOOD output low if the output feedback voltage exits a ±8% window around the regulation point. Furthermore, an input overvoltage protection been utilized by shutting down both power MOSFETs when V_{IN} rises above 22.5V to protect internal devices.

Multiphase operation can be easily employed by connecting SYNC pin to an external oscillator . Up to 6 phases can be paralleled to run simultaneously a good current sharing guaranteed by current mode control loop.

Pulling the RUN pin below 1V forces the controller into its shutdown state, turning off both power MOSFETs and most of the internal control circuitry. At light load currents, Burst Mode operation can be enabled to achieve higher efficiency compared to continuous mode (CCM) by setting MODE pin to INTV_{CC} . The TRACK/SS pin is used for power supply tracking and soft-start programming. See the Applications Information section.

### APPLICATIONS INFORMATION

The  typical  LTM4622  application  circuit  is  shown  in Figure  24.  External  component  selection  is  primarily determined by the input voltage, the output voltage and the maximum load current. See Table 7 for specific external capacitor requirements for a particular application.

### V_{IN}  to V_{OUT} Step-Down Ratios

There are restrictions in the maximum V_{IN} and V_{OUT} step down ratio that can be achieved for a given input voltage due to the minimum off-time and minimum on-time limits of the regulator . The minimum off-time limit imposes a maximum duty cycle which can be calculated as:

![Equation as printed (p. 9)](ltm4622/figures/ltm4622-eq01.png)

$$D_{MAX} = 1 - t_{OFF(MIN)} \cdot f_{SW}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where t_{OFF(MIN)} is the minimum off-time, 45ns typical for LTM4622, and f_{SW} is the switching frequency. Conversely the minimum on-time limit imposes a minimum duty cycle of the converter which can be calculated as:

![Equation as printed (p. 9)](ltm4622/figures/ltm4622-eq02.png)

$$D_{MIN} = t_{ON(MIN)} \cdot f_{SW}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where t_{ON(MIN)} is the minimum on-time, 20ns typical for LTM4622. In the rare cases where the minimum duty cycle is surpassed, the output voltage will still remain in regulation, but the switching frequency will decrease from its programmed value. Note that additional thermal derating may be applied. See the Thermal Considerations and Output Current Derating section in this data sheet.

### Output Voltage Programming

The PWM controller has an internal 0.6V reference voltage. As shown in the Block Diagram, a 60.4k 0.5% internal feedback resistor connects V_{OUT} and FB pins together . Adding a resistor R_{FB} from FB pin to GND programs the output voltage:

![Equation as printed (p. 10)](ltm4622/figures/ltm4622-eq03.png)

$$R_{FB} = \frac{0.6V}{V_{OUT} - 0.6V} \cdot 60.4k$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

**Table 1. V_{FB} Resistor Table vs Various Output Voltages** ([table-05-p10-data.csv](ltm4622/tables/table-05-p10-data.csv), p. 10)

| V_{OUT} (V) | 0.6 | 1.0 | 1.2 | 1.5 | 1.8 | 2.5 | 3.3 | 5.0 |
|---|---|---|---|---|---|---|---|---|
| R_{FB} (k) | OPEN | 90.9 | 60.4 | 40.2 | 30.1 | 19.1 | 13.3 | 8.25 |

Pease note that for 2.5 to 5V output, a higher operating frequency is required to optimize inductor current ripple. See Operating Frequency section.

For parallel operation of N-channels LTM4622, the following equation can be used to solve for R_{FB} :

![Equation as printed (p. 10)](ltm4622/figures/ltm4622-eq04.png)

$$R_{FB} = \frac{0.6V}{V_{OUT} - 0.6V} \cdot \frac{60.4k}{N}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

### Input Decoupling Capacitors

The  LTM4622 module should be connected to a low AC-impedance DC source. For each regulator channel, one piece 4.7µF input ceramic capacitor is required for RMS ripple current decoupling. Bulk input capacitor is only needed when the input source impedance is compromised by long inductive leads, traces or not enough source capacitance. The bulk capacitor can be an electrolytic aluminum capacitor and polymer capacitor .

Without considering the inductor current ripple, for each output, the RMS current of the input capacitor can be estimated as:

![Equation as printed (p. 10)](ltm4622/figures/ltm4622-eq05.png)

$$I_{CIN ( RMS )} = \frac{I_{OUT ( MAX )}}{\eta\%} \cdot \sqrt{D \cdot ( 1 - D )}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where is the estimated efficiency of the power module.

### Output Decoupling Capacitors

With an optimized high frequency, high bandwidth design, only single piece of 22µF low ESR output ceramic capacitor is required for each LTM4622 output to achieve low output voltage ripple and very good transient response. Additional output filtering may be required by the system designer, if further reduction of output ripples or dynamic transient spikes is required. Table 6 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 1.25A (50%) load step transient. Multiphase operation will reduce effective output ripple as a function of the number of phases. The Application Note 77 discusses this noise reduction versus output ripple current cancellation, but the output capacitance will be more a function of stability and transient response. The Analog Devices LTpowerCAD®  design tool is available to download online for output ripple, stability and transient response analysis, and for calculating the output ripple reduction as the number of phases implemented increases by N times.

### Burst Mode Operation

In applications where high efficiency at intermediate current are more important than output voltage ripple, Burst Mode operation could  be  used  by  connecting  SYNC/ MODE pin to INTV_{CC} to improve light load efficiency. In Burst  Mode operation, a current reversal comparator (I_{REV} ) detects the negative inductor current and shuts off the bottom power MOSFET , resulting in discontinuous operation and increased efficiency. Both power MOSFETs will remain off and the output capacitor will supply the load current until the COMP voltage rises above the zero current level to initiate another cycle.

### Forced Continuous Mode (FCM) Operation

In applications where fixed frequency operation is more critical than low current efficiency, and where the lowest output ripple is desired, FCM operation should be used. FCM operation can be enabled by tying the SYNC/MODE pin to GND. In this mode, inductor current is allowed to reverse during low output loads, the COMP voltage is in control of the current comparator threshold throughout, and the top MOSFET always turns on with each oscillator pulse. During start-up, FCM is disabled and inductor current is prevented from reversing until the LTM4622's output voltage is in regulation.

### Operating Frequency

The operating frequency of the LTM4622 is optimized to achieve the compact package size and the minimum out-put ripple voltage while still keeping high efficiency. The default operating frequency is internally set to 1MHz. In most applications, no additional frequency adjusting is required.

If any operating frequency other than 1MHz is required by application, the operating frequency can be increased by adding a resistor , R_{FSET} , between the FREQ pin and GND, as shown in Figure 26. The operating frequency can be calculated as:

![Equation as printed (p. 11)](ltm4622/figures/ltm4622-eq06.png)

$$f ( Hz ) = \frac{3.2 e 11}{324 k \| R_{FSET} ( \Omega )}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Please note a minimum switching frequency is required for given V_{IN} , V_{OUT} operating conditions to keep a maximum peak-to-peak inductor ripple current below 1.2A for the LTM4622.

The peak-to-peak inductor ripple current can be calculated as:

![Equation as printed (p. 11)](ltm4622/figures/ltm4622-eq07.png)

$$\Delta I_{P - P} = \frac{V_{OUT}}{1 \mu H} \left( 1 - \frac{V_{OUT}}{V_{IN}} \right) \cdot \frac{1}{f_{SW} ( MHz )}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The maximum 1.2A peak-to-peak inductor ripple current is enforced due to the nature of the valley current mode control to maintain output voltage regulation at no load.

To reduce switching current ripple, 1.5MHz to 2.5MHz operating frequency is required for 2.5V to 5.5V output with R_{FSET} to GND.

**V_{OUT} / f_{SW} (MHz) / R_{FSET} (kΩ) Frequency Setting Table** ([table-06-p11-data.csv](ltm4622/tables/table-06-p11-data.csv), p. 11)

| V_{OUT} | 0.6V TO 1.8V | 2.5V | 3.3V | 5V |
|---|---|---|---|---|
| f_{SW} (MHz) | 1 | 1.5 | 2 | 2.5 |
| R_{FSET} (kΩ) | Open | 649 | 324 | 215 |

The operating frequency can also be decreased by adding a resistor between the FREQ pin and INTV_{CC} , calculated as:

![Equation as printed (p. 11)](ltm4622/figures/ltm4622-eq08.png)

$$f ( Hz ) = 1 \, MHz - \frac{5.67 e 11}{R_{FSET} \left( \Omega \right)}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The programmable operating frequency range is from 800kHz to 4MHz.

### Frequency Synchronization

The power module has a phase-locked loop comprised of an internal voltage controlled oscillator and a phase detector .  This allows the internal top MOSFET turn-on to be locked to the rising edge of the external clock. The external clock frequency range must be within ±30% around the set operating frequency. A pulse detection circuit is used to detect a clock on the SYNC/MODE pin to turn on the phase-locked loop. The pulse width of the clock has to be at least 100ns. The clock high level must be above 2V and clock low level below 0.3V. The presence of an external clock will place both regulator channels into FCM operation. During the start-up of the regulator , the phaselocked loop function is disabled.

### Multiphase Operation

For output loads that demand more than 2.5A of current, two outputs in the LTM4622 or even multiple LTM4622s can be paralleled to run out of phase to provide more output current without increasing input and output voltage ripples.

A  multiphase  power  supply  significantly  reduces  the amount of ripple current in both the input and output capacitors. The RMS input ripple current is reduced by, and the effective ripple frequency is multiplied by, the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by the number of phases used when all of the outputs are tied together to achieve a single high output current design.

The two switching mode regulator channels inside the LTM4622 are internally set to operate 180° out of phase. Multiple  LTM4622s  could  easily  operate  90  degrees, 60 degrees or 45 degrees shift which corresponds to 4-phase, 6-phase or 8-phase operation by letting SYNC/ MODE of the LTM4622 synchronize to an external multiphase oscillator like the LTC® 6902. Figure 2 shows a 4-phase design example for clock phasing.

![Figure 2. Example of Clock Phasing for 4-Phase Operation with LTC6902](ltm4622/figures/ltm4622-f016.png)

*Figure 2. Example of Clock Phasing for 4-Phase Operation with LTC6902*

The LTM4622 device is an inherently current mode controlled device, so parallel modules will have very good current sharing. This will balance the thermals on the design. Please tie RUN, TRACK/SS, FB and COMP pin of each paralleling channel together . Figure 28 shows an example of parallel operation and pin connection.

### Input RMS Ripple Current Cancellation

The Application Note 77 provides a detailed explanation of multiphase operation. The input RMS ripple current cancellation mathematical derivations are presented, and a graph is displayed representing the RMS ripple current reduction as a function of the number of interleaved phases. Figure 3 shows this graph.

![Figure 3. Input RMS Current Ratios to DC Load Current as a Function of Duty Cycle](ltm4622/figures/ltm4622-f017.png)

*Figure 3. Input RMS Current Ratios to DC Load Current as a Function of Duty Cycle*

Digitized data: [input-rms-current-ratios-to-dc-load-current-as-a-function-of-duty-cycle.csv](ltm4622/curves/input-rms-current-ratios-to-dc-load-current-as-a-function-of-duty-cycle.csv) (x: VOUT/VIN; y: ratio) — values read off the printed plot by the digitizer, not published data.

### Soft-Start and Output Voltage T racking

The TRACK/SS pin provides a means to either soft-start the regulator or track it to a different power supply. A capacitor on the TRACK/SS pin will program the ramp rate of the output voltage. An internal 1.2µA current source will charge up the external soft-start capacitor towards INTV_{CC} voltage. When the TRACK/SS voltage is below 0.6V, it will take over the internal 0.6V reference voltage to control the output voltage. The total soft-start time can be calculated as:

![Equation as printed (p. 12)](ltm4622/figures/ltm4622-eq09.png)

$$t_{SS} = 0.6 \cdot \frac{C_{SS}}{1.2 \mu A}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where  C_{SS}   is  the  capacitance  on  the  TRACK/SS  pin. Current foldback and FCM are disabled during the softstart process.

The LTM4622 has internal 400µs soft-start time when TRACK/SS leave floating.

Output  voltage  tracking  can  also  be  programmed externally using the TRACK/SS pin. The output can be tracked up and down with another regulator . Figure 4 and Figure 5 show an example waveform and schematic of a Ratiometric tracking where the subordinate regulator's output slew rate is proportional to the main's.

Since the subordinate regulator's TRACK/SS is connected to the main's output through a R_{TR(TOP)} /R_{TR(BOT)} resistor divider and its voltage used to regulate the subordinate output voltage when TRACK/SS voltage is below 0.6V, the subordinate output voltage and the main output voltage should satisfy the following equation during the start-up.

![Figure 4. Output Ratiometric T racking Waveform](ltm4622/figures/ltm4622-f018.png)

*Figure 4. Output Ratiometric T racking Waveform*

![Figure 5. Example Schematic of Ratiometric Output Voltage T racking](ltm4622/figures/ltm4622-f019.png)

*Figure 5. Example Schematic of Ratiometric Output Voltage T racking*

![Equation as printed (p. 13)](ltm4622/figures/ltm4622-eq10.png)

$$V_{OUT(SL)} \cdot \frac{R_{FB(SL)}}{R_{FB(SL)} + 60.4k} = \\
V_{OUT(MA)} \cdot \frac{R_{TR(BOT)}}{R_{TR(TOP)} + R_{TR(BOT)}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The R_{FB(SL)} is the feedback resistor and the R_{TR(TOP)} / R_{TR(BOT)}  is the resistor divider on the TRACK/SS pin of the subordinate regulator , as shown in Figure 5.

Following the upper equation, the main's output slew rate (MR) and the subordinate's output slew rate (SR) in Volts/ Time is determined by:

![Equation as printed (p. 13)](ltm4622/figures/ltm4622-eq11.png)

For  example,  V_{OUT(MA)}   =  1.5V,  MR  =  1.4V/1ms  and V_{OUT(SL)}  = 1.2V, SR = 1.2V/1ms. From the equation, we could solve out that R_{TR(TOP)} = 60.4k and R_{TR(BOT)} = 40.2k is a good combination for the Ratiometric tracking.

The TRACK pins will have the 1.2µA current source on when a resistive divider is used to implement tracking on that specific channel. This will impose an offset on the TRACK pin input. Smaller values resistors with the same ratios as the resistor values calculated from the above equation can be used. For example, where the 60.4k is used then a 6.04k can be used to reduce the TRACK pin offset to a negligible value.

The Coincident output tracking can be recognized as a special Ratiometric output tracking which the main's output slew rate (MR) is the same as the subordinate's output slew rate (SR), as waveform shown in Figure 6.

From  the  equation,  we  could  easily  find  out  that,  in the  Coincident  tracking,  the  subordinate  regulator's

![Figure 6. Output Coincident T racking Waveform](ltm4622/figures/ltm4622-f020.png)

*Figure 6. Output Coincident T racking Waveform*

TRACK/SS pin resistor divider is always the same as its feedback divider .

![Equation as printed (p. 14)](ltm4622/figures/ltm4622-eq12.png)

$$\frac{R_{FB ( SL )}}{R_{FB ( SL )} + 60.4 k} = \frac{R_{TR ( BOT )}}{R_{TR ( TOP )} + R_{TR ( BOT )}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

For example, R_{TR(TOP)} = 60.4k and R_{TR(BOT)} = 60.4k is a good combination for Coincident tracking for V_{OUT(MA)} = 1.5V and V_{OUT(SL)} = 1.2V application.

### Power Good

The PGOOD pins are open drain pins that can be used to monitor valid output voltage regulation. This pin monitors a ±8% window around the regulation point. A resistor can be pulled up to a particular supply voltage for monitoring. To prevent unwanted PGOOD glitches during transients or dynamic V_{OUT} changes, the LTM4622's PGOOD falling edge includes a blanking delay of approximately 40µs.

### Stability compensation

The  LTM4622  module  internal  compensation  loop  is designed  and  optimized  for  low  ESR  ceramic  output capacitors only application. Table 7 is provided for most application requirements. The LTpowerCAD Design Tool is available to down for control loop optimization.

### RUN Enable

Pulling the RUN pin to ground forces the LTM4622 into its shutdown state, turning off both power MOSFETs and most of its internal control circuitry. T rying the RUN pin voltage above 1.27V will turn on the entire chip.

### Low Input Application

The LTM4622 is capable to run from 3.3V input when the V_{IN} pin is tied to INTV_{CC} pin. See Figure 27 for the application circuit. Please note the INTV_{CC} pin has 3.6V ABS MAX voltage rating.

### Pre-Biased Output Start-Up

There may be situations that require the power supply to start up with a pre-bias on the output capacitors. In this case, it is desirable to start up without discharging that output pre-bias. The LTM4622 can safely power up into a pre-biased output without discharging it.

The LTM4622 accomplishes this by forcing discontinuous mode (DCM) operation until the TRACK/SS pin voltage reaches 0.6V reference voltage. This will prevent the BG from turning on during the pre-biased output start-up which would discharge the output.

### Overtemperature Protection

The internal overtemperature protection monitors the junction  temperature  of  the  module.  If  the  junction temperature reaches approximately 160°C, both power switches will be turned off until the temperature drops about 15°C cooler .

### Input Overvoltage Protection

In order to protect the internal power MOSFET devices against transient voltage spikes, the LTM4622 constantly monitors each V_{IN} pin for an overvoltage condition. When V_{IN}  rises above 22.5V, the regulator suspends operation by shutting off both power MOSFETs on the corresponding channel. Once V_{IN} drops below 21.5V, the regulator immediately resumes normal operation. The regulator executes its soft-start function when exiting an overvoltage condition.

### Thermal Considerations and Output Current Derating

The thermal resistances reported in the Pin Configuration section of the data sheet are consistent with those parameters defined by JESD51-9 and are intended for use with finite element analysis (FEA) software modeling tools that leverage the outcome of thermal modeling, simulation, and correlation to hardware evaluation performed on a µModule package mounted to a hardware test boardalso defined by JESD51-9 (Test Boards for Area Array Surface Mount Package Thermal Measurements). The motivation for providing these thermal coefficients in found in JESD51-12 (Guidelines for Reporting and Using Electronic Package Thermal Information).

Many designers may opt to use laboratory equipment and a test vehicle such as the demo board to anticipate the µModule regulator's thermal performance in their application at various electrical and environmental operating conditions to compliment any FEA activities. Without FEA software, the thermal resistances reported in the Pin Configuration section are in-and-of themselves not relevant to providing guidance of thermal performance; instead, the derating curves provided in the data sheet can be used in a manner that yields insight and guidance pertaining to one's application usage, and can be adapted to correlate thermal performance to one's own application.

The Pin Configuration section typically gives four thermal coefficients explicitly defined in JESD 51-12; these coefficients are quoted or paraphrased below:

1. θ_{JA} , the thermal resistance from junction to ambient, is the natural convection junction-to-ambient air thermal resistance measured in a one cubic foot sealed enclosure. This environment is sometimes referred to as still air although natural convection causes the air to move. This value is determined with the part mounted to a JESD 51-9 defined test board, which does not reflect an actual application or viable operating condition .
2. θ_{JCbottom} , the thermal resistance from junction to ambient, is the natural convection junction-to-ambient air thermal resistance measured in a one cubic foot sealed enclosure. This environment is sometimes referred to as still air although natural convection causes the air to move. This value is determined with the part mounted to a JESD 51-9 defined test board, which does not reflect an actual application or viable operating condition .
3. θ_{JCtop} , the thermal resistance from junction to top of the product case, is determined with nearly all of the component power dissipation flowing through the top of the package. As the electrical connections of the typical µModule are on the bottom of the package, it is rare for an application to operate such that most of the heat flows from the junction to the top of the part. As in the case of θ_{JCbottom} , this value may be useful for comparing packages but the test conditions don't generally match the user's application .
4. θ_{JB} , the thermal resistance from junction to the printed circuit board (PCB), is the junction-to-board thermal resistance where almost all of the heat flows through the bottom of the µModule and into the board, and is really the sum of the θ_{JCbottom} and the thermal resistance of the bottom of the part through the solder joints and through a portion of the board. The board temperature is measured a specified distance from the package, using a two sided, two layer board. This board is described in JESD 51-9.

A graphical representation of the aforementioned thermal resistances is given in Figure 7; blue resistances are contained within the µModule regulator , whereas green resistances are external to the µModule.

As a practical matter , it should be clear to the reader that no individual or sub-group of the four thermal resistance parameters defined by JESD 51-12 or provided in the Pin Configuration section replicates or conveys normal

![Figure 7. Graphical Representation of JESD 51-12 Thermal Coefficients](ltm4622/figures/ltm4622-f021.png)

*Figure 7. Graphical Representation of JESD 51-12 Thermal Coefficients*

operating conditions of a µModule. For example, in normal board-mounted applications, never does 100% of the device's total power loss (heat) thermally conduct exclusively through the top or exclusively through bottom of the µModule-as the standard defines for θ_{JCtop} and θ_{JCbottom}, respectively. In practice, power loss is thermally dissipated in both directions away from the package-granted, in the absence of a heat sink and airflow, a majority of the heat flow is into the board.

Within a SIP (system-in-package) module, be aware there are multiple power devices and components dissipating power, with a consequence that the thermal resistances relative to different junctions of components or die are not exactly linear with respect to total package power loss. To reconcile this complication without sacrificing modeling simplicity-but also, not ignoring practical realities-an approach has been taken using FEA software modeling along with laboratory testing in a controlled-environment chamber to reasonably define and correlate the thermal resistance values supplied in this data sheet: (1) Initially, FEA software is used to accurately build the mechanical geometry of the µModule and the specified PCB with all of the correct material coefficients along with accurate power loss source definitions; (2) this model simulates a software-defined JEDEC environment consistent with JSED51-12 to predict power loss heat flow and temperature readings at different interfaces that enable the calculation of the JEDEC-defined thermal resistance values; (3) the model and FEA software is used to evaluate the µModule with heat sink and airflow; (4) having solved for and analyzed these thermal resistance values and simulated various operating conditions in the software model, a thorough laboratory evaluation replicates the simulated conditions with thermo-couples within a controlled-environment chamber while operating the device at the same power loss as that which was simulated. An outcome of this process and due-diligence yields a set of derating curves provided in other sections of this data sheet. After these laboratory test have been performed and correlated to the µModule model, then the θ_{JB} and θ_{BA} are summed together to correlate quite well with the µModule model with no airflow or heat sinking in a properly define chamber . This θ_{JB} + θ_{BA} value is shown in the Pin Configuration section and should accurately equal the θ_{JA} value because approximately 100% of power loss flows from the junction through the board into ambient with no airflow or top mounted heat sink.

The 1V, 1.5V, 2.5V, 3.3V and 5V power loss curves in Figure 8 to Figure 12 can be used in coordination with the load current derating curves in Figure 13 to Figure 21 for calculating an approximate θ_{JA} thermal resistance for the  LTM4622  (in  two-phase  single  output  operation) with no heat sinking and various airflow conditions. The power loss curves are taken at room temperature, and are increased with multiplicative factors of 1.35 assuming junction temperature at 120°C. The derating curves are plotted with the output current starting at 5A and the ambient temperature at 40°C. These output voltages are chosen to include the lower and higher output voltage ranges for correlating the thermal resistance. Thermal models are derived from several temperature measurements in a controlled temperature chamber along with thermal modeling analysis. The junction temperatures are monitored while ambient temperature is increased with and without airflow. The power loss increase with ambient temperature change is factored into the derating curves. The junctions are maintained at 120°C maximum while lowering output current or power with increasing ambient temperature. The decreased output current will decrease the internal module loss as ambient temperature is increased. The monitored junction temperature of 120°C minus the ambient operating temperature specifies how much module temperature rise can be allowed. As an example in Figure 15 the load current is derated to ~3A at ~102°C with no air or heat sink and the power loss for the 5V to 1.5V at 3A output is about 0.95W. The 0.95W loss is calculated with the ~0.7W room temperature loss from the 5V to 1.5V power loss curve at 3A, and the 1.35 multiplying factor . If the 102°C ambient temperature is subtracted from the 120°C junction temperature, then the difference of 18°C divided by 0.95W equals a 19°C/W θ_{JA} thermal resistance. Table 3 specifies a 19 - 20°C/W value which is very close. Table 2 to Table 6 provide equivalent thermal resistances for 1V, 1.5V, 2.5V, 3.3V and 5V outputs with and without airflow. The derived thermal resistances in Table 2 to Table 6 for the various conditions can be multiplied by the calculated power loss as a function of ambient temperature to derive temperature rise above

![Figure 8. 1V Output Power Loss](ltm4622/figures/ltm4622-f022.png)

*Figure 8. 1V Output Power Loss*

Digitized data: [1v-output-power-loss.csv](ltm4622/curves/1v-output-power-loss.csv) (x: A; y: W) — values read off the printed plot by the digitizer, not published data.

![Figure 9. 1.5V Output Power Loss](ltm4622/figures/ltm4622-f025.png)

*Figure 9. 1.5V Output Power Loss*

Digitized data: [1-5v-output-power-loss.csv](ltm4622/curves/1-5v-output-power-loss.csv) (x: A; y: W) — values read off the printed plot by the digitizer, not published data.

![Figure 10. 2.5V Output Power Loss](ltm4622/figures/ltm4622-f028.png)

*Figure 10. 2.5V Output Power Loss*

Digitized data: [2-5v-output-power-loss.csv](ltm4622/curves/2-5v-output-power-loss.csv) (x: A; y: W) — values read off the printed plot by the digitizer, not published data.

![Figure 11. 3.3V Output Power Loss](ltm4622/figures/ltm4622-f023.png)

*Figure 11. 3.3V Output Power Loss*

Digitized data: [3-3v-output-power-loss.csv](ltm4622/curves/3-3v-output-power-loss.csv) (x: A; y: W) — values read off the printed plot by the digitizer, not published data.

![Figure 12. 5V Output Power Loss](ltm4622/figures/ltm4622-f026.png)

*Figure 12. 5V Output Power Loss*

Digitized data: [5v-output-power-loss.csv](ltm4622/curves/5v-output-power-loss.csv) (x: A; y: W) — values read off the printed plot by the digitizer, not published data.

![Figure 13. 5V to 1V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f029.png)

*Figure 13. 5V to 1V Derating Curve, No Heat Sink*

Digitized data: [5v-to-1v-derating-curve-no-heat-sink.csv](ltm4622/curves/5v-to-1v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 14. 12V to 1V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f024.png)

*Figure 14. 12V to 1V Derating Curve, No Heat Sink*

Digitized data: [12v-to-1v-derating-curve-no-heat-sink.csv](ltm4622/curves/12v-to-1v-derating-curve-no-heat-sink.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 15. 5V to 1.5V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f027.png)

*Figure 15. 5V to 1.5V Derating Curve, No Heat Sink*

Digitized data: [5v-to-1-5v-derating-curve-no-heat-sink.csv](ltm4622/curves/5v-to-1-5v-derating-curve-no-heat-sink.csv) (x: °C; y: ) — values read off the printed plot by the digitizer, not published data.

![Figure 16. 12V to 1.5V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f030.png)

*Figure 16. 12V to 1.5V Derating Curve, No Heat Sink*

Digitized data: [12v-to-1-5v-derating-curve-no-heat-sink.csv](ltm4622/curves/12v-to-1-5v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 17. 5V to 2.5V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f031.png)

*Figure 17. 5V to 2.5V Derating Curve, No Heat Sink*

Digitized data: [5v-to-2-5v-derating-curve-no-heat-sink.csv](ltm4622/curves/5v-to-2-5v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 18. 12V to 2.5V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f032.png)

*Figure 18. 12V to 2.5V Derating Curve, No Heat Sink*

Digitized data: [12v-to-2-5v-derating-curve-no-heat-sink.csv](ltm4622/curves/12v-to-2-5v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 19. 5V to 3.3V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f033.png)

*Figure 19. 5V to 3.3V Derating Curve, No Heat Sink*

Digitized data: [5v-to-3-3v-derating-curve-no-heat-sink.csv](ltm4622/curves/5v-to-3-3v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 20. 12V to 3.3V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f034.png)

*Figure 20. 12V to 3.3V Derating Curve, No Heat Sink*

Digitized data: [12v-to-3-3v-derating-curve-no-heat-sink.csv](ltm4622/curves/12v-to-3-3v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 21. 12V to 5V Derating Curve, No Heat Sink](ltm4622/figures/ltm4622-f035.png)

*Figure 21. 12V to 5V Derating Curve, No Heat Sink*

Digitized data: [12v-to-5v-derating-curve-no-heat-sink.csv](ltm4622/curves/12v-to-5v-derating-curve-no-heat-sink.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

**Table 2. 1V Output** ([table-07-p18-data.csv](ltm4622/tables/table-07-p18-data.csv), p. 18)

| DERATING CURVE | V_{IN} (V) | POWER LOSS CURVE | AIRFLOW (LFM) | HEAT SINK | θ_{JA} (°C/W) |
|---|---|---|---|---|---|
| Figure 13, Figure 14 | 5, 12 | Figure 8 | 0 | None | 19 to 20 |
| Figure 13, Figure 14 | 5, 12 | Figure 8 | 200 | None | 17 to 18 |
| Figure 13, Figure 14 | 5, 12 | Figure 8 | 400 | None | 17 to 18 |

**Table 3. 1.5V Output** ([table-08-p18-data.csv](ltm4622/tables/table-08-p18-data.csv), p. 18)

| DERATING CURVE | V_{IN} (V) | POWER LOSS CURVE | AIRFLOW (LFM) | HEAT SINK | θ_{JA} (°C/W) |
|---|---|---|---|---|---|
| Figure 15, Figure 16 | 5, 12 | Figure 9 | 0 | None | 19 to 20 |
| Figure 15, Figure 16 | 5, 12 | Figure 9 | 200 | None | 17 to 18 |
| Figure 15, Figure 16 | 5, 12 | Figure 9 | 400 | None | 17 to 18 |



### Table 4. 2.5V Output

**Table 4. 2.5V Output** ([table-09-p19-data.csv](ltm4622/tables/table-09-p19-data.csv), p. 19)

| DERATING CURVE | V_{IN} (V) | POWER LOSS CURVE | AIRFLOW (LFM) | HEAT SINK | θ_{JA} (°C/W) |
|---|---|---|---|---|---|
| Figure 17, Figure 18 | 5, 12 | Figure 10 | 0 | None | 19 to 20 |
| Figure 17, Figure 18 | 5, 12 | Figure 10 | 200 | None | 17 to 18 |
| Figure 17, Figure 18 | 5, 12 | Figure 10 | 400 | None | 17 to 18 |

### Table 5. 3.3V Output

**Table 5. 3.3V Output** ([table-10-p19-data.csv](ltm4622/tables/table-10-p19-data.csv), p. 19)

| DERATING CURVE | V_{IN} (V) | POWER LOSS CURVE | AIRFLOW (LFM) | HEAT SINK | θ_{JA} (°C/W) |
|---|---|---|---|---|---|
| Figure 19, Figure 20 | 5, 12 | Figure 11 | 0 | None | 19 to 20 |
| Figure 19, Figure 20 | 5, 12 | Figure 11 | 200 | None | 17 to 18 |
| Figure 19, Figure 20 | 5, 12 | Figure 11 | 400 | None | 17 to 18 |

### Table 6. 5V Output

**Table 6. 5V Output** ([table-11-p19-data.csv](ltm4622/tables/table-11-p19-data.csv), p. 19)

| DERATING CURVE | V_{IN} (V) | POWER LOSS CURVE | AIRFLOW (LFM) | HEAT SINK | θ_{JA} (°C/W) |
|---|---|---|---|---|---|
| Figure 21 | 12 | Figure 12 | 0 | None | 19 to 20 |
| Figure 21 | 12 | Figure 12 | 200 | None | 17 to 18 |
| Figure 21 | 12 | Figure 12 | 400 | None | 17 to 18 |

### Table 7. Output Voltage Response for Each Regulator Channel vs Component Matrix (See Figure 24) 1.25A Load Step Typical Measured Values

**Table 7. Output Voltage Response for Each Regulator Channel vs Component Matrix (See Figure 24) 1.25A Load Step Typical Measured Values** ([table-12-p19-data.csv](ltm4622/tables/table-12-p19-data.csv), p. 19)

| C_{IN} (CERAMIC) | PART NUMBER | VALUE | C_{OUT1} (CERAMIC) | PART NUMBER | VALUE | C_{OUT2} (BULK) | PART NUMBER | VALUE |  |  |  |  |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Murata | GRM188R61E475KE11# | 4.7µF, 25V, 0603, X5R | Murata | GRM21R60J476ME15# | 47µF, 6.3V, 0805, X5R | Panasonic | 6TPC150M | 150µF, 6.3V 3.5 × 2.8 × 1.4mm |  |  |  |  |
| Murata | GRM188R61E106MA73# | 10µF, 25V, 0603, X5R | Murata | GRM188R60J226MEA0# | 22µF, 6.3V, 0603, X5R | Sanyo |  |  |  |  |  |  |
| Taiyo Yuden | TMK212BJ475KG-T | 4.7µF, 25V, 0805, X5R | Taiyo Yuden | JMK212BJ476MG-T | 47µF, 6.3V, 0805, X5R |  |  |  |  |  |  |  |
| V_{OUT} (V) | C_{IN} (CERAMIC) (µF) | C_{IN} (BULK) (µF) | C_{OUT1} (CERAMIC) (µF) | C_{OUT2} (BULK) (µF) | C_{FF} (pF) | V_{IN} (V) | DROOP (mV) | P-P DERIVATION (mV) | RECOVERY TIME (µs) | LOAD STEP (A) | LOAD STEP SLEW RATE (A/µs) | R_{FB} (kΩ) |
| 1 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 103 | 4 | 1.25 | 10 | 90.9 |
| 1 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 52 | 10 | 1.25 | 10 | 90.9 |
| 1.2 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 113 | 4 | 1.25 | 10 | 60.4 |
| 1.2 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 56 | 10 | 1.25 | 10 | 60.4 |
| 1.5 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 131 | 8 | 1.25 | 10 | 40.2 |
| 1.5 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 61 | 14 | 1.25 | 10 | 40.2 |
| 1.8 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 150 | 8 | 1.25 | 10 | 30.1 |
| 1.8 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 67 | 16 | 1.25 | 10 | 30.1 |
| 2.5 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 184 | 8 | 1.25 | 10 | 19.1 |
| 2.5 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 78 | 20 | 1.25 | 10 | 19.1 |
| 3.3 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 200 | 12 | 1.25 | 10 | 13.3 |
| 3.3 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 78 | 35 | 1.25 | 10 | 13.3 |
| 5 | 10 | 0 | 47 | 0 | 0 | 5, 12 | 0 | 309 | 12 | 1.25 | 10 | 8.25 |
| 5 | 10 | 0 | 10 | 150 | 0 | 5, 12 | 0 | 114 | 60 | 1.25 | 10 | 8.25 |

ambient, thus maximum junction temperature. Room temperature power loss can be derived from the efficiency curves in the Typical Performance Characteristics section and adjusted with the above ambient temperature multiplicative factors. The PCB is a 1.6mm thick four-layer board with two-ounce copper for the two outer layers and one ounce-copper for the two inner layers. The PCB dimensions are 95mm × 76mm.

Figure 22 shows a measured temperature picture of the LTM4622 with no heatsink and no airflow, from 12V input down to 3.3V and 5V output with 2.5A DC current on each.

![Figure 22.  Thermal Picture, 12V Input, 3.3V and 5V Output, 2.5A DC Each  Output with No Airflow and No Heat Sink](ltm4622/figures/ltm4622-f036.png)

*Figure 22.  Thermal Picture, 12V Input, 3.3V and 5V Output, 2.5A DC Each  Output with No Airflow and No Heat Sink*

### Safety Considerations

The LTM4622 modules do not provide galvanic isolation from V_{IN} to V_{OUT} . There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. The device does support thermal shutdown and over current protection.

### Layout Checklist/Example

The high integration of LTM4622 makes the PCB layout very simple and easy. However , to optimize its electrical and thermal performance, some layout considerations are still necessary.

- Use large PCB copper areas for high current paths, including V_{IN} , GND, V_{OUT1} , and V_{OUT2} . It helps to minimize the PCB conduction loss and thermal stress.
- Place high frequency ceramic input and output capacitors next to the V_{IN} , PGND, and V_{OUT} pins to minimize high frequency noise.
- Place  a  dedicated  power  ground  layer  underneath the unit.
- To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers.
- Do not put the via directly on the pad, unless they are capped or plated over .
- Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND to GND underneath the unit.
- For parallel modules, tie the V_{OUT} , V_{FB} , and COMP pins together . Use an internal layer to closely connect these pins together . The TRACK pin can be tied a common capacitor for regulator soft-start.
- Bring out test points on the signal pins for monitoring.

Figure 23 gives a good example of the recommended layout.

![Figure 23.  Recommended PCB Layout](ltm4622/figures/ltm4622-f037.png)

*Figure 23.  Recommended PCB Layout*

### TYPICAL APPLICATIONS

![Figure 24.  4V_{IN} to 20V_{IN} , 1V and 1.8V Output at 2.5A Design](ltm4622/figures/ltm4622-f038.png)

*Figure 24.  4V_{IN} to 20V_{IN} , 1V and 1.8V Output at 2.5A Design*

![Figure 25. 4V_{IN} to 20V_{IN} , 1.2V T wo Phase in Parallel 5A Design](ltm4622/figures/ltm4622-f039.png)

*Figure 25. 4V_{IN} to 20V_{IN} , 1.2V T wo Phase in Parallel 5A Design*

![Figure 26.  8V_{IN} to 20V_{IN} , 3.3V and 5V Output at 2.5A with 2MHz Switching Frequency](ltm4622/figures/ltm4622-f040.png)

*Figure 26.  8V_{IN} to 20V_{IN} , 3.3V and 5V Output at 2.5A with 2MHz Switching Frequency*

![Figure 27.  3.3V_{IN} , 1.5V and 1.2V Output at 2.5A Design with Output Coincident T racking](ltm4622/figures/ltm4622-f041.png)

*Figure 27.  3.3V_{IN} , 1.5V and 1.2V Output at 2.5A Design with Output Coincident T racking*

![Figure 28. 4 Phase, 1V Output at 10A Design with LTC6902](ltm4622/figures/ltm4622-f042.png)

*Figure 28. 4 Phase, 1V Output at 10A Design with LTC6902*

### PACKAGE DESCRIPTION

![other (p. 24)](ltm4622/figures/ltm4622-f043.png)

PACKAGE ROW AND COLUMN LABELING MAY VARY AMONG µModule PRODUCTS. REVIEW EACH PACKAGE LAYOUT CAREFULLY.

### LTM4622 Component LGA and BGA Pinout

**LTM4622 Component LGA and BGA Pinout** ([table-13-p24-pin.csv](ltm4622/tables/table-13-p24-pin.csv), p. 24)

| NUMBER | NAME |
|---|---|
| A1 | V_{OUT2} |
| A2 | V_{IN2} |
| A3 | TRACK/SS2 |
| A4 | FB2 |
| A5 | COMP2 |
| B1 | V_{OUT2} |
| B2 | RUN2 |
| B3 | V_{IN2} |
| B4 | PGOOD2 |
| B5 | GND |
| C1 | GND |
| C2 | GND |
| C3 | INTV_{CC} |
| C4 | FREQ |
| C5 | SYNC/MODE |
| D1 | V_{OUT1} |
| D2 | RUN1 |
| D3 | V_{IN1} |
| D4 | PGOOD1 |
| D5 | GND |
| E1 | V_{OUT1} |
| E2 | V_{IN1} |
| E3 | TRACK/SS1 |
| E4 | FB1 |
| E5 | COMP1 |

### LGA Package 25-Lead (6.25mm × 6.25mm × 1.82mm) (Reference LTC DWG # 05-08-1949 Rev Ø)

![LGA Package 25-Lead (6.25mm × 6.25mm × 1.82mm) (Reference LTC DWG # 05-08-1949 Rev Ø)](ltm4622/figures/ltm4622-f045.png)

*LGA Package 25-Lead (6.25mm × 6.25mm × 1.82mm) (Reference LTC DWG # 05-08-1949 Rev Ø)*

**LGA Package Dimensions Table** — [table-14-p25-data.csv](ltm4622/tables/table-14-p25-data.csv), p. 25

| DIMENSIONS |  |  |  |
|---|---|---|---|
| SYMBOL | MIN | NOM | MAX |
| A | 1.72 | 1.82 | 1.92 |
| b | 0.60 | 0.63 | 0.66 |
| D |  | 6.25 |  |
| E |  | 6.25 |  |
| e |  | 1.27 |  |
| F |  | 5.08 |  |
| G |  | 5.08 |  |
| H1 | 0.27 | 0.32 | 0.37 |
| H2 | 1.45 | 1.50 | 1.55 |
| aaa |  |  | 0.15 |
| bbb |  |  | 0.10 |
| eee |  |  | 0.15 |
| TOTAL NUMBER   OF LGA PADS: 25 |  |  |  |

### BGA Package 25-Lead (6.25mm × 6.25mm × 2.42mm) (Reference LTC DWG # 05-08-1502 Rev A)

![other (p. 26)](ltm4622/figures/ltm4622-f046.png)

**BGA Package Dimensions Table** — [table-15-p26-data.csv](ltm4622/tables/table-15-p26-data.csv), p. 26

| DIMENSIONS |  |  |  |  |
|---|---|---|---|---|
| SYMBOL | CONDITIONS | MIN | TYP | MAX |
| A |  | 2.22 | 2.42 | 2.62 |
| A1 | BALL HT | 0.50 | 0.60 | 0.70 |
| A2 |  | 1.72 | 1.82 | 1.92 |
| b | BALL DIMENSION | 0.60 | 0.75 | 0.90 |
| b1 | PAD DIMENSION | 0.60 | 0.63 | 0.66 |
| D |  |  | 6.25 |  |
| E |  |  | 6.25 |  |
| e |  |  | 1.27 |  |
| F |  |  | 5.08 |  |
| G |  |  | 5.08 |  |
| H1 | SUBSTRATE THK | 0.27 | 0.32 | 0.37 |
| H2 | MOLD CAP HT | 1.45 | 1.50 | 1.55 |
| aaa |  |  |  | 0.15 |
| bbb |  |  |  | 0.10 |
| ccc |  |  |  | 0.20 |
| ddd |  |  |  | 0.30 |
| eee |  |  |  | 0.15 |
| TOTAL NUMBER   OF BALLS: 25 |  |  |  |  |

### REVISION HISTORY

**Revision History** ([table-16-p27-data.csv](ltm4622/tables/table-16-p27-data.csv), p. 27)

| REV | DATE | DESCRIPTION | PAGE NUMBER |
|---|---|---|---|
| A | 08/15 | Added "Single 5A" to Title and Features. | 1 |
| B | 01/16 | Added BGA package. | 1, 2, 25, 26 |
| C | 11/16 | Corrected equations of tracking start-up time from R_{TR(TOP)}/[R_{TR(TOP)} + R_{TR(BOT)}] to R_{TR(BOT)}/[R_{TR(TOP)} + R_{TR(BOT)}]. | 13, 14 |
| D | 05/17 | Changed MSL Rating from 3 to 4. | 2 |
| E | 01/18 | Removed unnecessary sentence from Pre-Biased Output Start-Up section. | 14 |
| F | 03/18 | Corrected R_{FSET} to GND. | 9, 11 |
| G | 09/18 | Split common V_{IN} into V_{IN1} and V_{IN2}. | 1, 2, 3, 7, 8, 13, 22, 23, 24 |
| H | 02/20 | Added text to Operating Frequency. | 11 |
| H | 02/20 | Changed resistors' value for LTC6902. | 12, 23 |
| I | 02/23 | Changed master to main and slave to subordinate. | All |
| I | 02/23 | Fixed major formatting issues. | 15 – 23 |
| I | 02/23 | Updated Synchronization Frequency of the LTC6902. | 12, 23 |
| I | 02/23 | Added ink marking statement to package photos. | 28 |
| J | 08/24 | Added the Product Selection Guide table. | 1 |
| J | 08/24 | Corrected Turn-On Time and Track Pin Soft-Start Pull-Up Current to 1.2µA in Electrical Characteristics table. | 3 |
| J | 08/24 | Updated Electrical Characteristics notes. | 4 |
| J | 08/24 | Corrected Track Pin Soft-Start Pull-Up Current to 1.2µA in Pin Functions section. | 7 |
| J | 08/24 | Corrected Track Pin Soft-Start Pull-Up Current to 1.2µA in Soft-Start and Output Voltage Tracking section. | 12, 13 |

### PACKAGE PHOTOS

**Part marking is either ink mark or laser mark**

![other (p. 28)](ltm4622/figures/ltm4622-f048.png)

![other (p. 28)](ltm4622/figures/ltm4622-f050.png)




### DESIGN RESOURCES

**Design Resources** ([table-17-p28-data.csv](ltm4622/tables/table-17-p28-data.csv), p. 28)

| SUBJECT | DESCRIPTION |
|---|---|
| µModule Design and Manufacturing Resources | Design: • Selector Guides • Demo Boards and Gerber Files • Free Simulation Tools \| Manufacturing: • Quick Start Guide • PCB Design, Assembly and Manufacturing Guidelines • Package and Board Level Reliability |
| µModule Regulator Products Search | 1. Sort table of products by parameters and download the result as a spread sheet. 2. Search using the Quick Power Search parametric table. ![Sort table of products by parameters and download the result as a spread sheet. Search using the Quick Power Search parametric table.](ltm4622/figures/ltm4622-f060.png)
| Digital Power System Management | Analog Devices' family of digital power supply management ICs are highly integrated solutions that offer essential functions, including power supply monitoring, supervision, margining and sequencing, and feature EEPROM for storing user configurations and fault logging. |

### RELATED PARTS

**Related Parts** ([table-18-p28-data.csv](ltm4622/tables/table-18-p28-data.csv), p. 28)

| PART NUMBER | DESCRIPTION | COMMENTS |
|---|---|---|
| LTM4623 | 20V_{IN}, 3A Step-Down µModule Regulator | 4V ≤ V_{IN} ≤ 20V, 0.6V ≤ V_{OUT} ≤ 5.5V, PLL Input, CLKOUT, V_{OUT} Tracking, PGOOD, 6.25mm × 6.25mm × 1.82mm LGA |
| LTM4624 | 14V_{IN}, 4A Step-Down µModule Regulator | 4V ≤ V_{IN} ≤ 14V, 0.6V ≤ V_{OUT} ≤ 5.5V, V_{OUT} Tracking, PGOOD, 6.25mm × 6.25mm × 5.01mm BGA |
| LTM4625 | 20V_{IN}, 5A Step-Down µModule Regulator | 4V ≤ V_{IN} ≤ 20V, 0.6V ≤ V_{OUT} ≤ 5.5V, PLL Input, CLKOUT, V_{OUT} Tracking, PGOOD, 6.25mm × 6.25mm × 5.01mm BGA |
| LTM4619 | Dual 26V, 4A Step-Down µModule Regulator | 4.5V ≤ V_{IN} ≤ 26.5V, 0.8V ≤ V_{OUT} ≤ 5V, PLL Input, V_{OUT} Tracking, PGOOD, 15mm × 15mm × 2.82mm LGA |
| LTM4618 | 26V_{IN}, 6A Step-Down µModule Regulator | 4.5V ≤ V_{IN} ≤ 26.5V, 0.8V ≤ V_{OUT} ≤ 5V, PLL Input, V_{OUT} Tracking, 9mm × 15mm × 4.32mm LGA |
| LTM4614 | Dual 5V, 4A µModule Regulator | 2.375V ≤ V_{IN} ≤ 5.5V, 0.8V ≤ V_{OUT} ≤ 5V, 15mm × 15mm × 2.82mm LGA |
| LTC6902 | Multiphase Oscillator with Spread Spectrum Frequency Modulation | 2.7V ≤ V_{IN} ≤ 5.5V, 5kHz to 20MHz Frequency Range Quad Output Oscillator, 10-Pin MSOP Package |
| LTM4642 | 20V_{IN}, Dual 4A, Step-Down µModule Regulator | 4.5V ≤ V_{IN} ≤ 20V, 0.6V ≤ V_{OUT} ≤ 5.5V, 9mm × 11.25mm × 4.92mm BGA |
| LTM4631 | Ultrathin, Dual 10A, Step-Down µModule Regulator | 4.5V ≤ V_{IN} ≤ 15V, 0.6V ≤ V_{OUT} ≤ 1.8V, 16mm × 16mm × 1.91mm LGA |
| LTM4643 | Ultrathin, Quad 3A, Step-Down µModule Regulator | 4V ≤ V_{IN} ≤ 20V, 0.6V ≤ V_{OUT} ≤ 3.3V, 9mm × 15mm × 1.82mm LGA |
