---
type: Analog Component
title: "LTC6813-1 — 18-Cell Battery Stack Monitor with Daisy Chain Interface"
description: "18-Cell Battery Stack Monitor with Daisy Chain Interface"
resource: "https://www.analog.com/en/products/ltc6813-1.html"
tags: ["datasheet", "linear"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ltc6813-1.pdf"
    title: "LTC6813-1 data sheet"
    author: "team:analog-devices"
    last_modified: "11/20"
tables:
  - file: "ltc6813-1/tables/table-00-p3-abs_max.csv"
    title: "Absolute Maximum Ratings (Note 1)"
    page: 3
  - file: "ltc6813-1/tables/table-01-p3-data.csv"
    title: "Order Information — Automotive Products"
    page: 3
  - file: "ltc6813-1/tables/table-02-p4-spec.csv"
    title: "Electrical Characteristics"
    page: 4
  - file: "ltc6813-1/tables/table-03-p15-pin.csv"
    title: "Serial Port Pins"
    page: 15
  - file: "ltc6813-1/tables/table-04-p17-data.csv"
    title: "Improvements from the LTC6811-1 (Additional LTC6813-1 Features / Benefits / Relevant Data Sheet Section(s))"
    page: 17
  - file: "ltc6813-1/tables/table-05-p20-data.csv"
    title: "Table 1. Core Supply Current"
    page: 20
  - file: "ltc6813-1/tables/table-06-p20-data.csv"
    title: "Table 2. isoSPI Supply Current Equations"
    page: 20
  - file: "ltc6813-1/tables/table-07-p21-spec.csv"
    title: "Table 3. ADC Filter Bandwidth and Accuracy"
    page: 21
  - file: "ltc6813-1/tables/table-08-p22-spec.csv"
    title: "Table 4. ADC Range and Resolution"
    page: 22
  - file: "ltc6813-1/tables/table-09-p23-data.csv"
    title: "Table 5. Conversion and Synchronization Times for ADCV Command Measuring All 18 Cells in Different Modes"
    page: 23
  - file: "ltc6813-1/tables/table-10-p24-data.csv"
    title: "Table 6. Conversion Times for ADCV Command Measuring 3 Cells in Different Modes"
    page: 24
  - file: "ltc6813-1/tables/table-11-p25-data.csv"
    title: "Table 7. Conversion and Synchronization Times for ADAX Command Measuring All GPIOs and 2nd Reference in Different Modes"
    page: 25
  - file: "ltc6813-1/tables/table-12-p26-data.csv"
    title: "Table 8. Conversion and Synchronization Times for ADCVAX Command in Different Modes"
    page: 26
  - file: "ltc6813-1/tables/table-13-p27-data.csv"
    title: "Table 9. Conversion and Synchronization Times for ADSTAT Command Measuring SC, ITMP, VA, VD in Different Modes"
    page: 27
  - file: "ltc6813-1/tables/table-14-p28-data.csv"
    title: "Indication of Digital Redundancy Fault Codes"
    page: 28
  - file: "ltc6813-1/tables/table-15-p28-data.csv"
    title: "Table 10. ADC Path Redundancy Selection"
    page: 28
  - file: "ltc6813-1/tables/table-16-p29-data.csv"
    title: "Table 11. Conversion and Synchronization Times for ADCVSC Command in Different Modes"
    page: 29
  - file: "ltc6813-1/tables/table-17-p30-data.csv"
    title: "Table 12. Conversion Times for ADOL Command"
    page: 30
  - file: "ltc6813-1/tables/table-18-p31-data.csv"
    title: "Table 13. Self Test Command Summary"
    page: 31
  - file: "ltc6813-1/tables/table-19-p32-data.csv"
    title: "Table 14. (External C Pin Capacitance / Number of ADOW Commands Required in Steps 1 and 2)"
    page: 32
  - file: "ltc6813-1/tables/table-20-p34-data.csv"
    title: "Table 15. DCTO Settings"
    page: 34
  - file: "ltc6813-1/tables/table-21-p34-data.csv"
    title: "Table 16. (Watchdog Timer / Discharge Timer Reset Behavior)"
    page: 34
  - file: "ltc6813-1/tables/table-22-p34-data.csv"
    title: "Table 17. (DCTO Read Value / Discharge Time Left)"
    page: 34
  - file: "ltc6813-1/tables/table-23-p35-data.csv"
    title: "Reset Event / Device Behavior"
    page: 35
  - file: "ltc6813-1/tables/table-24-p37-data.csv"
    title: "Table 18. S Pin Pulse-Width Modulation Settings"
    page: 37
  - file: "ltc6813-1/tables/table-25-p38-register.csv"
    title: "Table 19. COMM Register Memory Map"
    page: 38
  - file: "ltc6813-1/tables/table-26-p38-register.csv"
    title: "Table 20. Write Codes for ICOMn[3:0] and FCOMn[3:0] on I2C Master"
    page: 38
  - file: "ltc6813-1/tables/table-27-p38-register.csv"
    title: "Table 21. Write Codes for ICOMn[3:0] and FCOMn[3:0] on SPI Master"
    page: 38
  - file: "ltc6813-1/tables/table-28-p39-register.csv"
    title: "Table 22. Read Codes for ICOMn[3:0] and FCOMn[3:0] on I2C Master"
    page: 39
  - file: "ltc6813-1/tables/table-29-p41-spec.csv"
    title: "Table 23. I2C Master Timing"
    page: 41
  - file: "ltc6813-1/tables/table-30-p41-spec.csv"
    title: "Table 24. SPI Master Timing"
    page: 41
  - file: "ltc6813-1/tables/table-31-p42-data.csv"
    title: "Table 25. S Pin Pulsing Behavior"
    page: 42
  - file: "ltc6813-1/tables/table-32-p48-data.csv"
    title: "Table 26. isoSPI Pulse Types"
    page: 48
  - file: "ltc6813-1/tables/table-33-p49-data.csv"
    title: "Table 27. Port B (Master) isoSPI Port Function"
    page: 49
  - file: "ltc6813-1/tables/table-34-p49-data.csv"
    title: "Table 28. Port A (Slave) isoSPI Port Function"
    page: 49
  - file: "ltc6813-1/tables/table-35-p55-data.csv"
    title: "Table 29. PEC Calculation for 0x0001"
    page: 55
  - file: "ltc6813-1/tables/table-36-p55-register.csv"
    title: "Table 30. Write/Read PEC Format"
    page: 55
  - file: "ltc6813-1/tables/table-37-p59-data.csv"
    title: "Table 31. Protocol Key"
    page: 59
  - file: "ltc6813-1/tables/table-38-p59-data.csv"
    title: "Table 32. Poll Command"
    page: 59
  - file: "ltc6813-1/tables/table-41-p59-register.csv"
    title: "Table 35. Command Format"
    page: 59
  - file: "ltc6813-1/tables/table-42-p60-data.csv"
    title: "Table 36. Command Codes"
    page: 60
  - file: "ltc6813-1/tables/table-43-p62-register.csv"
    title: "Table 37. Command Bit Descriptions"
    page: 62
  - file: "ltc6813-1/tables/table-44-p63-register.csv"
    title: "Table 38. Configuration Register Group A"
    page: 63
  - file: "ltc6813-1/tables/table-45-p63-register.csv"
    title: "Table 39. Configuration Register Group B"
    page: 63
  - file: "ltc6813-1/tables/table-46-p63-register.csv"
    title: "Table 40. Cell Voltage Register Group A"
    page: 63
  - file: "ltc6813-1/tables/table-47-p63-register.csv"
    title: "Table 41. Cell Voltage Register Group B"
    page: 63
  - file: "ltc6813-1/tables/table-48-p64-register.csv"
    title: "Table 42. Cell Voltage Register Group C"
    page: 64
  - file: "ltc6813-1/tables/table-49-p64-register.csv"
    title: "Table 43. Cell Voltage Register Group D"
    page: 64
  - file: "ltc6813-1/tables/table-50-p64-register.csv"
    title: "Table 44. Cell Voltage Register Group E"
    page: 64
  - file: "ltc6813-1/tables/table-51-p64-register.csv"
    title: "Table 45. Cell Voltage Register Group F"
    page: 64
  - file: "ltc6813-1/tables/table-52-p65-register.csv"
    title: "Table 46. Auxiliary Register Group A"
    page: 65
  - file: "ltc6813-1/tables/table-53-p65-register.csv"
    title: "Table 47. Auxiliary Register Group B"
    page: 65
  - file: "ltc6813-1/tables/table-54-p65-register.csv"
    title: "Table 48. Auxiliary Register Group C"
    page: 65
  - file: "ltc6813-1/tables/table-55-p65-register.csv"
    title: "Table 49. Auxiliary Register Group D"
    page: 65
  - file: "ltc6813-1/tables/table-56-p66-register.csv"
    title: "Table 50. Status Register Group A"
    page: 66
  - file: "ltc6813-1/tables/table-57-p66-register.csv"
    title: "Table 51. Status Register Group B"
    page: 66
  - file: "ltc6813-1/tables/table-58-p66-register.csv"
    title: "Table 52. COMM Register Group"
    page: 66
  - file: "ltc6813-1/tables/table-59-p66-register.csv"
    title: "Table 53. S Control Register Group"
    page: 66
  - file: "ltc6813-1/tables/table-60-p67-register.csv"
    title: "Table 54. PWM Register Group"
    page: 67
  - file: "ltc6813-1/tables/table-61-p67-register.csv"
    title: "Table 55. PWM/S Control Register Group B"
    page: 67
  - file: "ltc6813-1/tables/table-62-p68-register.csv"
    title: "Table 56. Memory Bit Descriptions"
    page: 68
  - file: "ltc6813-1/tables/table-63-p76-data.csv"
    title: "Table 57. Discharge Control During an ADCV Command with DCP = 0"
    page: 76
  - file: "ltc6813-1/tables/table-64-p84-data.csv"
    title: "Table 58. Recommended Transformers"
    page: 84
  - file: "ltc6813-1/tables/table-65-p84-data.csv"
    title: "Table 59. Recommended Common Mode Chokes"
    page: 84
  - file: "ltc6813-1/tables/table-66-p85-data.csv"
    title: "Table 60. Daisy Chain Serial Time Equations"
    page: 85
  - file: "ltc6813-1/tables/table-67-p89-data.csv"
    title: "Revision History"
    page: 89
  - file: "ltc6813-1/tables/table-68-p90-data.csv"
    title: "Related Parts"
    page: 90
figures:
  - file: "ltc6813-1/figures/ltc6813-1-eqx02.png"
    caption: "Equation as printed (p. 74)"
    type: equation
    page: 74
  - file: "ltc6813-1/figures/ltc6813-1-eqx03.png"
    caption: "Equation as printed (p. 79)"
    type: equation
    page: 79
  - file: "ltc6813-1/figures/ltc6813-1-eqx04.png"
    caption: "Equation as printed (p. 80)"
    type: equation
    page: 80
  - file: "ltc6813-1/figures/ltc6813-1-f000.png"
    caption: "19-Cell Monitor and Balance IC"
    type: "application_circuit"
    page: 1
  - file: "ltc6813-1/figures/ltc6813-1-f001.png"
    caption: "Cell 18 Measurement Error vs Temperature"
    type: "characteristic_curve"
    page: 1
  - file: "ltc6813-1/figures/ltc6813-1-f002.png"
    caption: ""
    type: "pinout"
    page: 3
  - file: "ltc6813-1/figures/ltc6813-1-f006.png"
    caption: "Measurement Error vs Temperature"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f007.png"
    caption: "Measurement Error vs Input, Fast Mode"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f008.png"
    caption: "Measurement Noise vs Input, Fast Mode"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f009.png"
    caption: "Measurement Error vs Input, Normal Mode"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f010.png"
    caption: "Measurement Noise vs Input, Normal Mode"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f011.png"
    caption: "Measurement Gain Error Thermal Hysteresis, Hot"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f012.png"
    caption: "Measurement Error vs Input, Filtered Mode"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f013.png"
    caption: "Measurement Noise vs Input, Filtered Mode"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f014.png"
    caption: "Measurement Gain Error Thermal Hysteresis, Cold"
    type: "characteristic_curve"
    page: 9
  - file: "ltc6813-1/figures/ltc6813-1-f015.png"
    caption: "Measurement Error Due to IR Reflow"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f016.png"
    caption: "Measurement Error vs V+"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f017.png"
    caption: "Measurement Error Due to a VREG AC Disturbance"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f019.png"
    caption: "Noise Filter Response"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f020.png"
    caption: "Top Cell Measurement Error vs V +"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f021.png"
    caption: "Measurement Error Due to a V + AC Disturbance"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f022.png"
    caption: "Measurement Error vs V REG"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f023.png"
    caption: "Measurement Error vs Common Mode Voltage"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f024.png"
    caption: "Measurement Error CMRR vs Frequency"
    type: "characteristic_curve"
    page: 10
  - file: "ltc6813-1/figures/ltc6813-1-f025.png"
    caption: "Cell Measurement Error Range vs Input RC Values"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f026.png"
    caption: "Sleep Supply Current vs V +"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f027.png"
    caption: "Measure Supply Current vs V +"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f028.png"
    caption: "GPIO Measurement Error vs Input RC Values"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f029.png"
    caption: "Standby Supply Current vs V +"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f030.png"
    caption: "VREF1 vs Temperature"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f031.png"
    caption: "Measurement Time vs Temperature"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f032.png"
    caption: "REFUP Supply Current vs V +"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f033.png"
    caption: "VREF2 vs Temperature"
    type: "characteristic_curve"
    page: 11
  - file: "ltc6813-1/figures/ltc6813-1-f035.png"
    caption: "Discharge Switch On-Resistance vs Cell Voltage"
    type: "characteristic_curve"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f036.png"
    caption: "VREF1  and V REF2  Power-Up"
    type: "scope_capture"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f037.png"
    caption: "Clock Frequency"
    type: "characteristic_curve"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f038.png"
    caption: "Internal Die Temperature Increase vs Discharge Current"
    type: "thermal"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f039.png"
    caption: "VREG  and V DRIVE  Power-Up"
    type: "scope_capture"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f040.png"
    caption: "IBIAS Voltage vs Temperature"
    type: "characteristic_curve"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f041.png"
    caption: "Internal Die Temperature Measurement Error vs Temperature"
    type: "characteristic_curve"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f042.png"
    caption: "Temperature"
    type: "characteristic_curve"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f043.png"
    caption: "IBIAS Voltage Load Regulation"
    type: "characteristic_curve"
    page: 13
  - file: "ltc6813-1/figures/ltc6813-1-f044.png"
    caption: "(Port A/Port B) vs IBIAS Current"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f045.png"
    caption: "(Port A/Port B) vs Temperature"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f046.png"
    caption: "Gain (Port A/Port B) vs Receiver Common Mode"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f047.png"
    caption: "Gain (Port A/Port B) vs Temperature"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f048.png"
    caption: "Voltage (Port A/Port B) vs Pulse Amplitude"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f049.png"
    caption: "Gain (Port A/Port B) vs ICMP Voltage"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f050.png"
    caption: "Typical Wake-Up Pulse Amplitude (Port A/Port B) vs Dwell Time"
    type: "characteristic_curve"
    page: 14
  - file: "ltc6813-1/figures/ltc6813-1-f051.png"
    caption: ""
    type: "block_diagram"
    page: 16
  - file: "ltc6813-1/figures/ltc6813-1-f053.png"
    caption: "Figure 1. LTC6813-1 Operation State Diagram"
    type: "block_diagram"
    page: 18
  - file: "ltc6813-1/figures/ltc6813-1-f054.png"
    caption: "Figure 2. Measurement Noise vs Input Voltage"
    type: "characteristic_curve"
    page: 21
  - file: "ltc6813-1/figures/ltc6813-1-f055.png"
    caption: "Figure 3. Timing for ADCV Command Measuring All 18 Cells"
    type: "timing_diagram"
    page: 23
  - file: "ltc6813-1/figures/ltc6813-1-f056.png"
    caption: "Figure 4. Timing for ADCV Command Measuring 3 Cells"
    type: "timing_diagram"
    page: 23
  - file: "ltc6813-1/figures/ltc6813-1-f057.png"
    caption: "Figure 5. Timing for ADAX Command Measuring All GPIOs and 2nd Reference"
    type: "timing_diagram"
    page: 24
  - file: "ltc6813-1/figures/ltc6813-1-f058.png"
    caption: "Figure 6. Timing of ADCVAX Command"
    type: "timing_diagram"
    page: 25
  - file: "ltc6813-1/figures/ltc6813-1-f059.png"
    caption: "Figure 7. Timing for ADSTAT Command Measuring SC, ITMP , VA, VD"
    type: "timing_diagram"
    page: 26
  - file: "ltc6813-1/figures/ltc6813-1-f060.png"
    caption: "Figure 8. Timing for ADCVSC Command Measuring All 18 Cells, SC"
    type: "timing_diagram"
    page: 29
  - file: "ltc6813-1/figures/ltc6813-1-f062.png"
    caption: "Figure 9. Timing for ADOL Command"
    type: "timing_diagram"
    page: 30
  - file: "ltc6813-1/figures/ltc6813-1-f064.png"
    caption: "Figure 10. Operation of LTC6813-1 ADC Self Test"
    type: "block_diagram"
    page: 31
  - file: "ltc6813-1/figures/ltc6813-1-f065.png"
    caption: "Figure 11. Watchdog and Discharge Timer"
    type: "block_diagram"
    page: 33
  - file: "ltc6813-1/figures/ltc6813-1-f066.png"
    caption: "Figure 12. LTC6813-1 I 2 C/SPI Master Using GPIOs"
    type: "block_diagram"
    page: 39
  - file: "ltc6813-1/figures/ltc6813-1-f069.png"
    caption: "Table 25. S Pin Pulsing Behavior"
    type: "other"
    page: 42
  - file: "ltc6813-1/figures/ltc6813-1-f070.png"
    caption: "Figure 15. 4-Wire SPI Configuration"
    type: "application_circuit"
    page: 43
  - file: "ltc6813-1/figures/ltc6813-1-f071.png"
    caption: "Figure 16. Timing Diagram of 4-Wire Serial Peripheral Interface"
    type: "timing_diagram"
    page: 44
  - file: "ltc6813-1/figures/ltc6813-1-f072.png"
    caption: "Figure 17. isoSPI Interface"
    type: "block_diagram"
    page: 44
  - file: "ltc6813-1/figures/ltc6813-1-f073.png"
    caption: "Figure 18.  Capacitive-Coupled Daisy-Chain Configuration"
    type: "application_circuit"
    page: 45
  - file: "ltc6813-1/figures/ltc6813-1-f074.png"
    caption: "Figure 19.  T ransformer-Isolated Daisy-Chain Configuration"
    type: "application_circuit"
    page: 46
  - file: "ltc6813-1/figures/ltc6813-1-f076.png"
    caption: "Figure 20. Single Device Using 2-Wire Port A"
    type: "application_circuit"
    page: 47
  - file: "ltc6813-1/figures/ltc6813-1-f077.png"
    caption: "Figure 21. Single Device Using 4-Wire Port A"
    type: "application_circuit"
    page: 47
  - file: "ltc6813-1/figures/ltc6813-1-f078.png"
    caption: "Figure 22. isoSPI Pulse Detail"
    type: "timing_diagram"
    page: 49
  - file: "ltc6813-1/figures/ltc6813-1-f079.png"
    caption: "Figure 23. Reversible isoSPI Daisy Chain"
    type: "application_circuit"
    page: 50
  - file: "ltc6813-1/figures/ltc6813-1-f081.png"
    caption: "Figure 24. Reversible isoSPI State Diagram"
    type: "block_diagram"
    page: 51
  - file: "ltc6813-1/figures/ltc6813-1-f082.png"
    caption: "Figure 25. isoSPI Timing Diagram"
    type: "timing_diagram"
    page: 52
  - file: "ltc6813-1/figures/ltc6813-1-f084.png"
    caption: "Figure 26. Wake-Up Detection and IDLE Timer"
    type: "timing_diagram"
    page: 53
  - file: "ltc6813-1/figures/ltc6813-1-f085.png"
    caption: "Figure 27. 15-Bit PEC Computation Circuit"
    type: "block_diagram"
    page: 55
  - file: "ltc6813-1/figures/ltc6813-1-f088.png"
    caption: "Figure 28. SDO Polling After an ADC Conversion Command (Single LTC6813-1)"
    type: "timing_diagram"
    page: 57
  - file: "ltc6813-1/figures/ltc6813-1-f089.png"
    caption: "Figure 29. SDO Polling Using PLADC Command (Single LTC6813-1)"
    type: "timing_diagram"
    page: 57
  - file: "ltc6813-1/figures/ltc6813-1-f090.png"
    caption: "Figure 30. SDO Polling After an ADC Conversion Command (Daisy-Chain Configuration)"
    type: "timing_diagram"
    page: 58
  - file: "ltc6813-1/figures/ltc6813-1-f091.png"
    caption: "Figure 31. SDO Polling Using PLADC Command (Daisy-Chain Configuration)"
    type: "timing_diagram"
    page: 58
  - file: "ltc6813-1/figures/ltc6813-1-f095.png"
    caption: ""
    type: "other"
    page: 64
  - file: "ltc6813-1/figures/ltc6813-1-f096.png"
    caption: ""
    type: "other"
    page: 66
  - file: "ltc6813-1/figures/ltc6813-1-f099.png"
    caption: "Figure 32. Simple V REG  Power Source Using NPN Pass Transistor"
    type: "application_circuit"
    page: 70
  - file: "ltc6813-1/figures/ltc6813-1-f100.png"
    caption: "Figure 33. V REG  Powered From Cell Stack with High Efficiency Regulator"
    type: "application_circuit"
    page: 70
  - file: "ltc6813-1/figures/ltc6813-1-f101.png"
    caption: "Figure 34. Internal ESD Protection Structures of the LTC6813-1"
    type: "block_diagram"
    page: 71
  - file: "ltc6813-1/figures/ltc6813-1-f102.png"
    caption: "Figure 35. Input Filter Structure Configurations"
    type: "application_circuit"
    page: 72
  - file: "ltc6813-1/figures/ltc6813-1-f103.png"
    caption: "Figure 36. Cell Measurement TME"
    type: "characteristic_curve"
    page: 73
  - file: "ltc6813-1/figures/ltc6813-1-f104.png"
    caption: "(b) Cell Measurement Error vs Input RC Values (Extra Conversion and Delay Before Measurement)"
    type: "other"
    page: 73
  - file: "ltc6813-1/figures/ltc6813-1-f105.png"
    caption: "Figure 37. ADC Command Order"
    type: "other"
    page: 73
  - file: "ltc6813-1/figures/ltc6813-1-f106.png"
    caption: "Figure 38. Internal/External Discharge Circuits"
    type: "application_circuit"
    page: 74
  - file: "ltc6813-1/figures/ltc6813-1-f107.png"
    caption: ""
    type: "other"
    page: 74
  - file: "ltc6813-1/figures/ltc6813-1-f108.png"
    caption: "Figure 39. 18-Cell Battery Stack Module with Active Balancing"
    type: "application_circuit"
    page: 75
  - file: "ltc6813-1/figures/ltc6813-1-f109.png"
    caption: ""
    type: "other"
    page: 77
  - file: "ltc6813-1/figures/ltc6813-1-f110.png"
    caption: "Figure 40. Balancing Self Test Circuit"
    type: "test_circuit"
    page: 77
  - file: "ltc6813-1/figures/ltc6813-1-f112.png"
    caption: "Figure 41. isoSPI Circuit"
    type: "application_circuit"
    page: 79
  - file: "ltc6813-1/figures/ltc6813-1-f113.png"
    caption: "Figure 42. Data Rate vs Cable Length"
    type: "characteristic_curve"
    page: 80
  - file: "ltc6813-1/figures/ltc6813-1-f114.png"
    caption: "Figure 43. Daisy Chain Interface Components"
    type: "application_circuit"
    page: 80
  - file: "ltc6813-1/figures/ltc6813-1-f116.png"
    caption: "Figure 44. Daisy Chain Interface Components on Single Board"
    type: "application_circuit"
    page: 81
  - file: "ltc6813-1/figures/ltc6813-1-f117.png"
    caption: "Figure 45. Capacitive Isolation Coupling for LTC6813-1s on the Same PCB"
    type: "application_circuit"
    page: 82
  - file: "ltc6813-1/figures/ltc6813-1-f118.png"
    caption: "Figure 46. Interfacing an LTC6813-1 with a μC Using an LTC6820 for Isolated SPI Control"
    type: "application_circuit"
    page: 83
  - file: "ltc6813-1/figures/ltc6813-1-f119.png"
    caption: "Figure 47. Cell Connection Schemes for 16 and 14 Cells"
    type: "application_circuit"
    page: 86
  - file: "ltc6813-1/figures/ltc6813-1-f120.png"
    caption: "Figure 48. Interfacing a Typical Hall-Effect Battery Current Sensor to Auxiliary ADC Inputs"
    type: "application_circuit"
    page: 86
  - file: "ltc6813-1/figures/ltc6813-1-f122.png"
    caption: "Figure 49. Typical Temperature Probe Circuit and Relative Output"
    type: "application_circuit"
    page: 87
  - file: "ltc6813-1/figures/ltc6813-1-f123.png"
    caption: "Figure 50. MUX Circuit Supports Sixteen Additional Analog Measurements"
    type: "test_circuit"
    page: 87
  - file: "ltc6813-1/figures/ltc6813-1-f124.png"
    caption: ""
    type: "other"
    page: 88
  - file: "ltc6813-1/figures/ltc6813-1-f126.png"
    caption: ""
    type: "application_circuit"
    page: 90
  - file: "ltc6813-1/figures/ltc6813-1-f129.png"
    caption: "VREF2 VREG Line Regulation"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f130.png"
    caption: "VREF2 V+ Line Regulation"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f131.png"
    caption: "VREF2 Load Regulation"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f132.png"
    caption: "VREF2 Thermal Hysteresis, Hot"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f133.png"
    caption: "VREF2 Thermal Hysteresis, Cold"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f134.png"
    caption: "VREF2 Change Due to IR Reflow"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f135.png"
    caption: "VDRIVE V+ Line Regulation"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f136.png"
    caption: "VDRIVE vs Temperature"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f137.png"
    caption: "VDRIVE Load Regulation"
    type: "characteristic_curve"
    page: 12
  - file: "ltc6813-1/figures/ltc6813-1-f138.png"
    caption: "Figure 13. STCOMM Timing Diagram for an I2C Master"
    type: "timing_diagram"
    page: 40
  - file: "ltc6813-1/figures/ltc6813-1-f139.png"
    caption: "Figure 14. STCOMM Timing Diagram for a SPI Master"
    type: "timing_diagram"
    page: 40
  - file: "ltc6813-1/figures/ltc6813-1-eq02.png"
    caption: "Equation as printed (p. 27)"
    type: equation
    page: 27
  - file: "ltc6813-1/figures/ltc6813-1-eq03.png"
    caption: "Equation as printed (p. 27)"
    type: equation
    page: 27
  - file: "ltc6813-1/figures/ltc6813-1-eq04.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ltc6813-1/figures/ltc6813-1-eq05.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ltc6813-1/figures/ltc6813-1-eq06.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ltc6813-1/figures/ltc6813-1-eq07.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ltc6813-1/figures/ltc6813-1-eq08.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ltc6813-1/figures/ltc6813-1-eq01.png"
    caption: "Equation as printed (p. 27)"
    type: equation
    page: 27
curves:
  - file: "ltc6813-1/curves/cell-18-measurement-error-vs-temperature.csv"
    caption: "Cell 18 Measurement Error vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f001.png"
    page: 1
    x_unit: "°C"
    y_unit: "mV"
    conditions: "CELL VOLTAGE = 3.3V, 5 TYPICAL UNITS"
  - file: "ltc6813-1/curves/cell-measurement-error-range-vs-input-rc-values.csv"
    caption: "Cell Measurement Error Range vs Input RC Values"
    figure: "ltc6813-1/figures/ltc6813-1-f025.png"
    page: 11
    x_unit: "Ω"
    y_unit: "mV"
  - file: "ltc6813-1/curves/cell-measurement-tme.csv"
    caption: "Figure 36. Cell Measurement TME"
    figure: "ltc6813-1/figures/ltc6813-1-f103.png"
    page: 73
    x_unit: "Ω"
    y_unit: "mV"
  - file: "ltc6813-1/curves/clock-frequency.csv"
    caption: "Clock Frequency"
    figure: "ltc6813-1/figures/ltc6813-1-f037.png"
    page: 13
    x_unit: "kHz"
    y_unit: "mA"
    conditions: "ISOMD = VREG, IB = 1mA"
  - file: "ltc6813-1/curves/data-rate-vs-cable-length.csv"
    caption: "Figure 42. Data Rate vs Cable Length"
    figure: "ltc6813-1/figures/ltc6813-1-f113.png"
    page: 80
    x_unit: "METERS"
    y_unit: "Mbps"
    conditions: "CAT5 ASSUMED"
  - file: "ltc6813-1/curves/discharge-switch-on-resistance-vs-cell-voltage.csv"
    caption: "Discharge Switch On-Resistance vs Cell Voltage"
    figure: "ltc6813-1/figures/ltc6813-1-f035.png"
    page: 13
    x_unit: "V"
    y_unit: "Ω"
  - file: "ltc6813-1/curves/gain-port-a-port-b-vs-icmp-voltage.csv"
    caption: "Gain (Port A/Port B) vs ICMP Voltage"
    figure: "ltc6813-1/figures/ltc6813-1-f049.png"
    page: 14
    x_unit: "V"
    y_unit: "V/V"
    conditions: "3 PARTS"
  - file: "ltc6813-1/curves/gain-port-a-port-b-vs-receiver-common-mode.csv"
    caption: "Gain (Port A/Port B) vs Receiver Common Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f046.png"
    page: 14
    x_unit: "V"
    y_unit: "V/V"
  - file: "ltc6813-1/curves/gain-port-a-port-b-vs-temperature.csv"
    caption: "Gain (Port A/Port B) vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f047.png"
    page: 14
    x_unit: "°C"
    y_unit: "V/V"
    conditions: "VICMP = 0.2V; VICMP = 1V"
  - file: "ltc6813-1/curves/gpio-measurement-error-vs-input-rc-values.csv"
    caption: "GPIO Measurement Error vs Input RC Values"
    figure: "ltc6813-1/figures/ltc6813-1-f028.png"
    page: 11
    x_unit: "Ω"
    y_unit: "mV"
    conditions: "TIME BETWEEN MEASUREMENTS > 3RC"
  - file: "ltc6813-1/curves/ibias-voltage-load-regulation.csv"
    caption: "IBIAS Voltage Load Regulation"
    figure: "ltc6813-1/figures/ltc6813-1-f043.png"
    page: 13
    x_unit: "µA"
    y_unit: "V"
  - file: "ltc6813-1/curves/ibias-voltage-vs-temperature.csv"
    caption: "IBIAS Voltage vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f040.png"
    page: 13
    x_unit: "°C"
    y_unit: "V"
    conditions: "I_B = 1mA, 3 PARTS"
  - file: "ltc6813-1/curves/internal-die-temperature-increase-vs-discharge-current.csv"
    caption: "Internal Die Temperature Increase vs Discharge Current"
    figure: "ltc6813-1/figures/ltc6813-1-f038.png"
    page: 13
    x_unit: "mA/CELL"
    y_unit: "°C"
  - file: "ltc6813-1/curves/internal-die-temperature-measurement-error-vs-temperature.csv"
    caption: "Internal Die Temperature Measurement Error vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f041.png"
    page: 13
    x_unit: "°C"
    y_unit: "°C"
    conditions: "5 TYPICAL UNITS"
  - file: "ltc6813-1/curves/measure-supply-current-vs-v.csv"
    caption: "Measure Supply Current vs V +"
    figure: "ltc6813-1/figures/ltc6813-1-f027.png"
    page: 11
    x_unit: "V"
    y_unit: "mA"
    conditions: "MEASURE SUPPLY CURRENT = V+ CURRENT + VREG CURRENT"
  - file: "ltc6813-1/curves/measurement-error-cmrr-vs-frequency.csv"
    caption: "Measurement Error CMRR vs Frequency"
    figure: "ltc6813-1/figures/ltc6813-1-f024.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VCM(IN) = 5VP-P, NORMAL MODE CONVERSIONS"
  - file: "ltc6813-1/curves/measurement-error-due-to-a-v-ac-disturbance.csv"
    caption: "Measurement Error Due to a V + AC Disturbance"
    figure: "ltc6813-1/figures/ltc6813-1-f021.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "V+ DC= 59.4V, V+ AC= 5VP-P, 1BIT CHANGE < -90dB, VREG GENERATED FROM DRIVE PIN, FIGURE 32"
  - file: "ltc6813-1/curves/measurement-error-due-to-a-vreg-ac-disturbance.csv"
    caption: "Measurement Error Due to a VREG AC Disturbance"
    figure: "ltc6813-1/figures/ltc6813-1-f017.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VREG(DC) = 5V, VREG(AC) = 0.5VP-P, 1BIT CHANGE < -70dB"
  - file: "ltc6813-1/curves/measurement-error-due-to-ir-reflow.csv"
    caption: "Measurement Error Due to IR Reflow"
    figure: "ltc6813-1/figures/ltc6813-1-f015.png"
    page: 10
    x_unit: "ppm"
    y_unit: "parts"
  - file: "ltc6813-1/curves/measurement-error-vs-common-mode-voltage.csv"
    caption: "Measurement Error vs Common Mode Voltage"
    figure: "ltc6813-1/figures/ltc6813-1-f023.png"
    page: 10
    x_unit: "V"
    y_unit: "mV"
    conditions: "C18 - C17 = 3.3V, V+ = 63.3V"
  - file: "ltc6813-1/curves/measurement-error-vs-input-fast-mode.csv"
    caption: "Measurement Error vs Input, Fast Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f007.png"
    page: 9
    x_unit: "V"
    y_unit: "mV"
    conditions: "10 ADC MEASUREMENTS AVERAGED AT EACH INPUT"
  - file: "ltc6813-1/curves/measurement-error-vs-input-filtered-mode.csv"
    caption: "Measurement Error vs Input, Filtered Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f012.png"
    page: 9
    x_unit: "V"
    y_unit: "mV"
    conditions: "10 ADC MEASUREMENTS AVERAGED AT EACH INPUT"
  - file: "ltc6813-1/curves/measurement-error-vs-input-normal-mode.csv"
    caption: "Measurement Error vs Input, Normal Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f009.png"
    page: 9
    x_unit: "V"
    y_unit: "mV"
    conditions: "10 ADC MEASUREMENTS AVERAGED AT EACH INPUT"
  - file: "ltc6813-1/curves/measurement-error-vs-temperature.csv"
    caption: "Measurement Error vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f006.png"
    page: 9
    x_unit: "°C"
    y_unit: "mV"
    conditions: "CELL VOLTAGE = 3.3V, 5 TYPICAL UNITS"
  - file: "ltc6813-1/curves/measurement-error-vs-v.csv"
    caption: "Measurement Error vs V+"
    figure: "ltc6813-1/figures/ltc6813-1-f016.png"
    page: 10
    x_unit: "V"
    y_unit: "mV"
    conditions: "MEASUREMENT ERROR OF CELL1 WITH 3.3V INPUT VREG GENERATED FROM DRIVE PIN, FIGURE 32"
  - file: "ltc6813-1/curves/measurement-error-vs-v-reg.csv"
    caption: "Measurement Error vs V REG"
    figure: "ltc6813-1/figures/ltc6813-1-f022.png"
    page: 10
    x_unit: "V"
    y_unit: "mV"
  - file: "ltc6813-1/curves/measurement-gain-error-thermal-hysteresis-cold.csv"
    caption: "Measurement Gain Error Thermal Hysteresis, Cold"
    figure: "ltc6813-1/figures/ltc6813-1-f014.png"
    page: 9
    x_unit: "ppm"
    y_unit: ""
    conditions: "TA = -40°C TO 25°C"
  - file: "ltc6813-1/curves/measurement-gain-error-thermal-hysteresis-hot.csv"
    caption: "Measurement Gain Error Thermal Hysteresis, Hot"
    figure: "ltc6813-1/figures/ltc6813-1-f011.png"
    page: 9
    x_unit: "ppm"
    y_unit: "parts"
    conditions: "TA = 85°C TO 25°C"
  - file: "ltc6813-1/curves/measurement-noise-vs-input-fast-mode.csv"
    caption: "Measurement Noise vs Input, Fast Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f008.png"
    page: 9
    x_unit: "V"
    y_unit: "mV"
  - file: "ltc6813-1/curves/measurement-noise-vs-input-filtered-mode.csv"
    caption: "Measurement Noise vs Input, Filtered Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f013.png"
    page: 9
    x_unit: "V"
    y_unit: "mV"
  - file: "ltc6813-1/curves/measurement-noise-vs-input-normal-mode.csv"
    caption: "Measurement Noise vs Input, Normal Mode"
    figure: "ltc6813-1/figures/ltc6813-1-f010.png"
    page: 9
    x_unit: "V"
    y_unit: "mV"
  - file: "ltc6813-1/curves/measurement-noise-vs-input-voltage.csv"
    caption: "Figure 2. Measurement Noise vs Input Voltage"
    figure: "ltc6813-1/figures/ltc6813-1-f054.png"
    page: 21
    x_unit: "V"
    y_unit: "mV"
  - file: "ltc6813-1/curves/measurement-time-vs-temperature.csv"
    caption: "Measurement Time vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f031.png"
    page: 11
    x_unit: "°C"
    y_unit: "ms"
  - file: "ltc6813-1/curves/noise-filter-response.csv"
    caption: "Noise Filter Response"
    figure: "ltc6813-1/figures/ltc6813-1-f019.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ltc6813-1/curves/port-a-port-b-vs-ibias-current.csv"
    caption: "(Port A/Port B) vs IBIAS Current"
    figure: "ltc6813-1/figures/ltc6813-1-f044.png"
    page: 14
    x_unit: "µA"
    y_unit: "mA"
  - file: "ltc6813-1/curves/port-a-port-b-vs-temperature.csv"
    caption: "(Port A/Port B) vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f045.png"
    page: 14
    x_unit: "°C"
    y_unit: "IB = 100uA"
    conditions: "I_B = 100µA, I_B = 1mA"
  - file: "ltc6813-1/curves/refup-supply-current-vs-v.csv"
    caption: "REFUP Supply Current vs V +"
    figure: "ltc6813-1/figures/ltc6813-1-f032.png"
    page: 11
    x_unit: "V"
    y_unit: "mA"
    conditions: "REFUP SUPPLY CURRENT = V+ CURRENT + VREG CURRENT"
  - file: "ltc6813-1/curves/sleep-supply-current-vs-v.csv"
    caption: "Sleep Supply Current vs V +"
    figure: "ltc6813-1/figures/ltc6813-1-f026.png"
    page: 11
    x_unit: "V"
    y_unit: "uA"
    conditions: "SLEEP SUPPLY CURRENT = V+ CURRENT + VREG CURRENT"
  - file: "ltc6813-1/curves/standby-supply-current-vs-v.csv"
    caption: "Standby Supply Current vs V +"
    figure: "ltc6813-1/figures/ltc6813-1-f029.png"
    page: 11
    x_unit: "V"
    y_unit: "µA"
    conditions: "STANDBY SUPPLY CURRENT = V+ CURRENT + VREG CURRENT"
  - file: "ltc6813-1/curves/temperature.csv"
    caption: "Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f042.png"
    page: 13
    x_unit: "°C"
    y_unit: "ISOMD = V-"
    conditions: "I_B = 1mA"
  - file: "ltc6813-1/curves/top-cell-measurement-error-vs-v.csv"
    caption: "Top Cell Measurement Error vs V +"
    figure: "ltc6813-1/figures/ltc6813-1-f020.png"
    page: 10
    x_unit: "V"
    y_unit: "mV"
    conditions: "C18–C17 = 3.3V, C18 = 59.4V"
  - file: "ltc6813-1/curves/typical-wake-up-pulse-amplitude-port-a-port-b-vs-dwell-time.csv"
    caption: "Typical Wake-Up Pulse Amplitude (Port A/Port B) vs Dwell Time"
    figure: "ltc6813-1/figures/ltc6813-1-f050.png"
    page: 14
    x_unit: "ns"
    y_unit: "mV"
  - file: "ltc6813-1/curves/vdrive-load-regulation.csv"
    caption: "VDRIVE Load Regulation"
    figure: "ltc6813-1/figures/ltc6813-1-f137.png"
    page: 12
    x_unit: "mA"
    y_unit: "mV"
    conditions: "V+ = 59.4V"
  - file: "ltc6813-1/curves/vdrive-v-line-regulation.csv"
    caption: "VDRIVE V+ Line Regulation"
    figure: "ltc6813-1/figures/ltc6813-1-f135.png"
    page: 12
    x_unit: "V"
    y_unit: "mV"
  - file: "ltc6813-1/curves/vdrive-vs-temperature.csv"
    caption: "VDRIVE vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f136.png"
    page: 12
    x_unit: "°C"
    y_unit: "V"
    conditions: "5 TYPICAL UNITS, NO LOAD"
  - file: "ltc6813-1/curves/voltage-port-a-port-b-vs-pulse-amplitude.csv"
    caption: "Voltage (Port A/Port B) vs Pulse Amplitude"
    figure: "ltc6813-1/figures/ltc6813-1-f048.png"
    page: 14
    x_unit: "V"
    y_unit: "IB = 100µA"
  - file: "ltc6813-1/curves/vref1-vs-temperature.csv"
    caption: "VREF1 vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f030.png"
    page: 11
    x_unit: "°C"
    y_unit: "V"
    conditions: "5 TYPICAL UNITS"
  - file: "ltc6813-1/curves/vref2-change-due-to-ir-reflow.csv"
    caption: "VREF2 Change Due to IR Reflow"
    figure: "ltc6813-1/figures/ltc6813-1-f134.png"
    page: 12
    x_unit: "ppm"
    y_unit: "parts"
  - file: "ltc6813-1/curves/vref2-load-regulation.csv"
    caption: "VREF2 Load Regulation"
    figure: "ltc6813-1/figures/ltc6813-1-f131.png"
    page: 12
    x_unit: "mA"
    y_unit: "ppm"
    conditions: "V+ = 59.4V, VREG = 5V"
  - file: "ltc6813-1/curves/vref2-thermal-hysteresis-cold.csv"
    caption: "VREF2 Thermal Hysteresis, Cold"
    figure: "ltc6813-1/figures/ltc6813-1-f133.png"
    page: 12
    x_unit: "ppm"
    y_unit: "parts"
    conditions: "TA = -40°C TO 25°C"
  - file: "ltc6813-1/curves/vref2-thermal-hysteresis-hot.csv"
    caption: "VREF2 Thermal Hysteresis, Hot"
    figure: "ltc6813-1/figures/ltc6813-1-f132.png"
    page: 12
    x_unit: "ppm"
    y_unit: "parts"
    conditions: "TA = 85°C TO 25°C"
  - file: "ltc6813-1/curves/vref2-v-line-regulation.csv"
    caption: "VREF2 V+ Line Regulation"
    figure: "ltc6813-1/figures/ltc6813-1-f130.png"
    page: 12
    x_unit: "V"
    y_unit: "ppm"
    conditions: "VREG GENERATED FROM DRIVE PIN, FIGURE 32"
  - file: "ltc6813-1/curves/vref2-vreg-line-regulation.csv"
    caption: "VREF2 VREG Line Regulation"
    figure: "ltc6813-1/figures/ltc6813-1-f129.png"
    page: 12
    x_unit: "V"
    y_unit: "ppm"
    conditions: "IL = 0.6mA"
  - file: "ltc6813-1/curves/vref2-vs-temperature.csv"
    caption: "VREF2 vs Temperature"
    figure: "ltc6813-1/figures/ltc6813-1-f033.png"
    page: 11
    x_unit: "°C"
    y_unit: "V"
    conditions: "5 TYPICAL UNITS"
agentforge:
  part_number: "LTC6813-1"
  datasheet_revision: "B"
  repairs: 8
  reading_order: "geometry"
---

# LTC6813-1 — 18-Cell Battery Stack Monitor with Daisy Chain Interface

*Datasheet: [LTC6813-1 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ltc6813-1.pdf)*

### FEATURES
<!-- page: 1 -->

- Measures Up to 18 Battery Cells in Series
- 2.2mV Maximum Total Measurement Error
- Stackable Architecture for High Voltage Systems
- Built-In isoSPI™ Interface
- 1Mb Isolated Serial Communications
- Uses a Single T wisted Pair , Up to 100 Meters
- Low EMI Susceptibility and Emissions
- Bidirectional for Broken Wire Protection
- 290µs to Measure All Cells in a System
- Synchronized Voltage and Current Measurement
- 16-Bit Delta-Sigma ADC with Programmable Noise Filter
- Engineered for ISO 26262-Compliant Systems
- Passive Cell Balancing Up to 200mA (Max) with Programmable Pulse-Width Modulation
- 9 General Purpose Digital I/O or Analog Inputs
- Temperature or Other Sensor Inputs
- Configurable as an $I^{2}C$ or SPI Master
- 6µA Sleep Mode Supply Current
- 64-Lead eLQFP Package
- AEC-Q100 Qualified for Automotive Applications

csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

### APPLICATIONS
<!-- page: 1 -->

- Electric and Hybrid Electric Vehicles
- Backup Battery Systems
- Grid Energy Storage
- High Power Portable Equipment

### DESCRIPTION
<!-- page: 1 -->

The LTC ® 6813-1 is a multicell battery stack monitor that measures up to 18 series connected battery cells with a total measurement error of less than 2.2mV. The cell measurement range of 0V to 5V makes the LTC6813-1 suitable for most battery chemistries. All 18 cells can be measured in 290µs, and lower data acquisition rates can be selected for high noise reduction.

Multiple LTC6813-1 devices can be connected in series, permitting simultaneous cell monitoring of long, high voltage battery strings. Each LTC6813-1 has an isoSPI interface for high speed, RF immune, long distance communications. Multiple devices are connected in a daisy chain with one host processor connection for all devices. This daisy chain can be operated bidirectionally, ensuring communication integrity, even in the event of a fault along the communication path.

The LTC6813-1 can be powered directly from the battery stack or from an isolated supply. The LTC6813-1 includes passive balancing for each cell, with individual PWM duty cycle control for each cell. Other features include an onboard 5V regulator , nine general purpose I/O lines and a sleep mode, where current consumption is reduced to 6µA.

All registered trademarks and trademarks are the property of their respective owners. Protected by U.S. patents, including 8908779, 9182428, 9270133.

### TYPICAL APPLICATION
<!-- pages: 1-3 -->

![application circuit (p. 1)](ltc6813-1/figures/ltc6813-1-f000.png)

*18-Cell Monitor and Balance IC*

![Cell 18 Measurement Error vs Temperature](ltc6813-1/figures/ltc6813-1-f001.png)

*Cell 18 Measurement Error vs Temperature*

Digitized data: [cell-18-measurement-error-vs-temperature.csv](ltc6813-1/curves/cell-18-measurement-error-vs-temperature.

### TABLE OF CONTENTS

- Features
- Applications
- Typical Application
- Description
- Absolute Maximum Ratings
- Order Information
- Pin Configuration
- Electrical Characteristics
- Typical Performance Characteristics
- Pin Functions
- Block Diagram
- Improvements from the LTC6811-1
- Operation
- State Diagram
- Core LTC6813-1 State Descriptions
- isoSPI State Descriptions
- Power Consumption
- ADC Operation
- Data Acquisition System Diagnostics
- Watchdog and Discharge Timer
- Reset Behaviors
- S Pin Pulse-Width Modulation for Cell Balancing
- Discharge Timer Monitor
- $I^{2}C$/SPI Master on LTC6813-1 Using GPIOs
- S Pin Pulsing Using the S Pin Control Settings
- S Pin Muting
- Serial Interface Overview
- 4-Wire Serial Peripheral Interface (SPI) Physical Layer
- 2-Wire Isolated Interface (isoSPI) Physical Layer.43
- Data Link Layer
- Network Layer
- Applications Information
- Providing DC Power
- Internal Protection and Filtering
- Cell Balancing
- Discharge Control During Cell Measurements
- Digital Communications
- Enhanced Applications
- Reading External Temperature Probes
- Package Description

### Revision History
- Related Parts
- A 03/19 Title Changed
- A 03/19 Added Automotive Qualification to Front Page Features
- A 03/19 Added Order Information for Tape and Reel
- A 03/19 Added Note Regarding Automotive Products
- A 03/19 Added Plot Measurement Error Due to IR Reflow
- A 03/19 Added Plot $V_{REF2}$ Change Due to IR Reflow
- A 03/19 Updated Figure 1 LTC6813-1 Operation State Diagram
- A 03/19 Voltage Range Changed from 2.988V to 3.012V to 2.990V to 3.014V (2.992V to 3.012V for LTC6813I) Under Accuracy Check Section
- A 03/19 Updated Figure 18 LTC6813-1 Operation State Diagram Capacitive Coupled Daisy-Chain Configuration
- A 03/19 Voltage Range Changed from 2.988V to 3.12V to 2.990V to 3.014V (2.992V to 3.012V for LTC6813I) Under REF, Table 56, Memory Bit Description
- A 03/19 Added PWMx (PWM Discharge Control) to Table 56. Memory Bit Description
- A 03/19 Rewrote the Section Improved Regulator Power Efficiency
- A 03/19 Updated Figure 34 Internal ESD Protection Structures of the LTC6813-1
- A 03/19 Updated Figure 37 ADC Command Order
- A 03/19 Renumbered the Steps for Discharge Verification Circuitry
- A 03/19 Updated Figure 43 Daisy Chain Interface Components
- A 03/19 Rewrote the Last Paragraph Section Transformer Selection Guide
- A 03/19 Updated Figure 45 Capacitive Isolation Coupling for LTC6813-1x on the Same PCB
- A 03/19 Updated Figure 47 Cell Connection Schemes for 16 and 14 Cells
- A 03/19 Updated Related Parts Section
- B 11/20 Added Section "Reset Behaviors" into the Table of Contents
- B 11/20 Rewrite to section entitled "Thermal Shutdown"
- B 11/20 Added new section entitled "RESET BEHAVIORS"
- B 11/20 Rewrite to section entitled "Implementing a Modular isoSPI Daisy Chain"
- B 11/20 Update to Table 58. Recommended Transformers
- B 11/20 Rewrite to section entitled "Related Parts"

### ABSOLUTE MAXIMUM RATINGS (Note 1)
<!-- page: 3 -->

**Absolute Maximum Ratings (Note 1)** ([table-00-p3-abs_max.csv](ltc6813-1/tables/table-00-p3-abs_max.csv), p. 3)

| PARAMETER | RATING |
|---|---|
| **Total Supply Voltage** |  |
| V⁺ to V⁻ | 112.5V |
| **Supply Voltage (Relative to C12)** |  |
| V⁺ to C12 | 50V |
| **Input Voltage (Relative to V⁻)** |  |
| C0 | −0.3V to 6V |
| C18 | −0.3V to MIN (V⁺ + 5.5V, 112.5V) |
| C(n), S(n) | −0.3V to MIN (8 • n, 112.5V) |
| IPA, IMA, IPB, IMB | −0.3V to $V_{REG}$ + 0.3V, ≤ 6V |
| DRIVE | −0.3V to 7V |
| All Other Pins | −0.3V to 6V |
| **Voltage Between Inputs** |  |
| C(n) to C(n−1), S(n) to C(n−1) | −0.3V to 8V |
| C18 to C15, C15 to C12, C12 to C9, C9 to C6, C6 to C3, C3 to C0 | −0.3V to 21V |
| **Current In/Out of Pins** |  |
| All Pins Except $V_{REG}$, IPA, IMA, IPB, IMB, C(n), S(n) | 10mA |
| IPA, IMA, IPB, IMB | 30mA |
| **Specified Junction Temperature Range** |  |
| LTC6813I-1 | −40°C to 85°C |
| LTC6813H-1 | −40°C to 125°C |
| Junction Temperature | 150°C |
| Storage Temperature Range | −65°C to 150°C |
| **Device HBM ESD Classification Level 1C** |  |
| **Device CDM ESD Classification Level C5** |  |

### ORDER INFORMATION
<!-- page: 3 -->

### AUTOMOTIVE PRODUCTS**
<!-- page: 3 -->

**Order Information — Automotive Products** ([table-01-p3-data.csv](ltc6813-1/tables/table-01-p3-data.csv), p. 3)

| TRAY (160PC) | TAPE AND REEL (1500PC) | PART MARKING* | PACKAGE DESCRIPTION | MSL RATING | SPECIFIED JUNCTION TEMPERATURE RANGE |
|---|---|---|---|---|---|
| LTC6813ILWE-1#3ZZPBF | LTC6813ILWE-1#3ZZTRPBF | LTC6813LWE-1 | 64-Lead Plastic eLQFP | 3 | –40°C to 85°C |
| LTC6813HLWE-1#3ZZPBF | LTC6813HLWE-1#3ZZTRPBF | LTC6813LWE-1 | 64-Lead Plastic eLQFP | 3 | –40°C to 125°C |

- **\*:** The temperature grade is identified by a label on the shipping container.
- **\*\*:** Versions of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These models are designated with a #3ZZ suffix. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models.

Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container .

Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix.

### PIN CONFIGURATION
<!-- pages: 3-9 -->

![pinout (p. 3)](ltc6813-1/figures/ltc6813-1-f002.png)

*The Function of These Pins Depends on the Connection of ISOMD: ISOMD Tied to $V^{-}$ : CSB, SCK, SDI, SDO ISOMD Tied to $V_{REG}$: IPA, IMA, NC, NC

**This Pin Must Be Connected to $V^{-}$

ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full specified temperature range, otherwise specifications are at $T_{A}$ = 25°C. The test conditions are $V^{+}$ = 59.4V, $V_{REG}$ = 5.0V unless otherwise noted. The ISOMD pin is tied to the $V^{-}$ pin, unless otherwise noted.

**Electrical Characteristics** ([table-02-p4-spec.csv](ltc6813-1/tables/table-02-p4-spec.csv), p. 4)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS | OVERTEMP |
|---|---|---|---|---|---|---|---|
| **ADC DC Specifications** |  |  |  |  |  |  |  |
| Measurement Resolution |  |  |  | 0.1 |  | mV/Bit |  |
| ADC Offset Voltage |  | (Note 2) |  | 0.1 |  | mV |  |
| ADC Gain Error |  | (Note 2) |  | 0.01 |  | % |  |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 0 |  | ±0.2 |  | mV |  |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1) = 2.0 |  |  | ±1.6 | mV |  |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 2.0, LTC6813I |  |  | ±1.8 | mV | ● |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 2.0, LTC6813H |  |  | ±2.0 | mV | ● |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1) = 3.3 |  |  | ±2.2 | mV |  |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 3.3, LTC6813I |  |  | ±3.0 | mV | ● |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 3.3, LTC6813H |  |  | ±3.3 | mV | ● |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1) = 4.2 |  |  | ±2.8 | mV |  |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 4.2, LTC6813I |  |  | ±3.8 | mV | ● |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 4.2, LTC6813H |  |  | ±4.2 | mV | ● |
| Total Measurement Error (TME) in Normal Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 5.0 |  | ±1 |  | mV |  |
| Total Measurement Error (TME) in Normal Mode |  | Sum of All Cells |  | ±0.05 | ±0.35 | % | ● |
| Total Measurement Error (TME) in Normal Mode |  | Internal Temperature, T = Maximum Specified Temperature |  | ±5 |  | °C |  |
| Total Measurement Error (TME) in Normal Mode |  | $V_{REG}$ Pin | −1 | −0.15 | 0 | % | ● |
| Total Measurement Error (TME) in Normal Mode |  | $V_{REF2}$ Pin | −0.05 | 0.05 | 0.20 | % | ● |
| Total Measurement Error (TME) in Normal Mode |  | Digital Supply Voltage, $V_{REGD}$ | −0.5 | 0.5 | 1.5 | % | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 0 |  | ±0.1 |  | mV |  |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1) = 2.0 |  |  | ±1.6 | mV |  |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 2.0, LTC6813I |  |  | ±1.8 | mV | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 2.0, LTC6813H |  |  | ±2.0 | mV | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1) = 3.3 |  |  | ±2.2 | mV |  |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 3.3, LTC6813I |  |  | ±3.0 | mV | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 3.3, LTC6813H |  |  | ±3.3 | mV | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1) = 4.2 |  |  | ±2.8 | mV |  |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 4.2, LTC6813I |  |  | ±3.8 | mV | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 4.2, LTC6813H |  |  | ±4.2 | mV | ● |
| Total Measurement Error (TME) in Filtered Mode |  | C(n) to C(n−1), GPIO(n) to $V^{-}$ = 5.0 |  | ±1 |  | mV |  |
| Total Measurement Error (TME) in Filtered Mode |  | Sum of All Cells |  | ±0.05 | ±0.35 | % | ● |
| Total Measurement Error (TME) in Filtered Mode |  | Internal Temperature, T = Maximum Specified Temperature |  | ±5 |  | °C |  |
| Total Measurement Error (TME) in Filtered Mode |  | $V_{REG}$ Pin | −1 | −0.15 | 0 | % | ● |
| Total Measurement Error (TME) in Filtered Mode |  | $V_{REF2}$ Pin | −0.05 | 0.05 | 0.20 | % | ● |
| Total Measurement Error (TME) in Filtered Mode |  | Digital Supply Voltage, $V_{REGD}$ | −0.5 | 0.8 | 1.5 | % | ● |
| Total Measurement Error (TME) in Fast Mode |  | C(n) to C(n–1); GPIO(n) to V⁻ = 0 |  | ±2 |  | mV |  |
| Total Measurement Error (TME) in Fast Mode |  | C(n) to C(n–1); GPIO(n) to V⁻ = 2.0 |  |  | ±4 | mV | ● |
| Total Measurement Error (TME) in Fast Mode |  | C(n) to C(n–1); GPIO(n) to V⁻ = 3.3 |  |  | ±6 | mV | ● |
| Total Measurement Error (TME) in Fast Mode |  | C(n) to C(n–1); GPIO(n) to V⁻ = 4.2 |  |  | ±8.3 | mV | ● |
| Total Measurement Error (TME) in Fast Mode |  | C(n) to C(n–1); GPIO(n) to V⁻ = 5.0 |  | ±10 |  | mV |  |
| Total Measurement Error (TME) in Fast Mode |  | Sum of All Cells |  | ±0.15 | ±0.5 | % | ● |
| Total Measurement Error (TME) in Fast Mode |  | Internal Temperature, T = Maximum Specified Temperature |  | ±5 |  | °C |  |
| Total Measurement Error (TME) in Fast Mode |  | $V_{REG}$ Pin | −1.5 | −0.15 | 1 | % | ● |
| Total Measurement Error (TME) in Fast Mode |  | $V_{REF2}$ Pin | −0.18 | 0.05 | 0.32 | % | ● |
| Total Measurement Error (TME) in Fast Mode |  | Digital Supply Voltage, $V_{REGD}$ | −2.5 | −0.4 | 2 | % | ● |
| Input Range |  | C(n) n = 1 to 18 | C(n–1) |  | C(n–1) + 5 | V | ● |
| Input Range |  | C0 | 0 |  | 1 | V | ● |
| Input Range |  | GPIO(n) n = 1 to 9 | 0 |  | 5 | V | ● |
| Input Leakage Current When Inputs Are Not Being Measured | $I_{L}$ | C(n) n = 0 to 18 |  | 10 | ±250 | nA | ● |
| Input Leakage Current When Inputs Are Not Being Measured | $I_{L}$ | GPIO(n) n = 1 to 9 |  | 10 | ±250 | nA | ● |
| Input Current When Inputs Are Being Measured (State: Core = MEASURE) |  | C(n) n = 0 to 18 |  | ±1 |  | µA |  |
| Input Current When Inputs Are Being Measured (State: Core = MEASURE) |  | GPIO(n) n = 1 to 9 |  | ±1 |  | µA |  |
| Input Current During Open Wire Detection |  |  | 70 | 100 | 130 | µA | ● |
| **Voltage Reference Specifications** |  |  |  |  |  |  |  |
| 1st Reference Voltage | $V_{REF1}$ | $V_{REF1}$ Pin, No Load | 3.0 | 3.15 | 3.3 | V | ● |
| 1st Reference Voltage TC | $V_{REF1}$ | $V_{REF1}$ Pin, No Load |  | 3 |  | ppm/°C |  |
| 1st Reference Voltage Thermal Hysteresis | $V_{REF1}$ | $V_{REF1}$ Pin, No Load |  | 20 |  | ppm |  |
| 1st Reference Voltage Long Term Drift | $V_{REF1}$ | $V_{REF1}$ Pin, No Load |  | 20 |  | ppm/√khr |  |
| 2nd Reference Voltage | $V_{REF2}$ | $V_{REF2}$ Pin, No Load | 2.993 | 3 | 3.007 | V | ● |
| 2nd Reference Voltage | $V_{REF2}$ | $V_{REF2}$ Pin, 5k Load to V⁻ | 2.992 | 3 | 3.008 | V | ● |
| 2nd Reference Voltage TC | $V_{REF2}$ | $V_{REF2}$ Pin, No Load |  | 10 |  | ppm/°C |  |
| 2nd Reference Voltage Thermal Hysteresis | $V_{REF2}$ | $V_{REF2}$ Pin, No Load |  | 100 |  | ppm |  |
| 2nd Reference Voltage Long Term Drift | $V_{REF2}$ | $V_{REF2}$ Pin, No Load |  | 60 |  | ppm/√khr |  |
| **General DC Specifications** |  |  |  |  |  |  |  |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = SLEEP, isoSPI = IDLE, $V_{REG}$ = 0V |  | 6.1 | 11 | µA |  |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = SLEEP, isoSPI = IDLE, $V_{REG}$ = 0V |  | 6.1 | 18 | µA | ● |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = SLEEP, isoSPI = IDLE, $V_{REG}$ = 5V |  | 3 | 5 | µA |  |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = SLEEP, isoSPI = IDLE, $V_{REG}$ = 5V |  | 3 | 9 | µA | ● |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = STANDBY | 9 | 14 | 22 | µA |  |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = STANDBY | 6 | 14 | 28 | µA | ● |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = REFUP | 0.4 | 0.55 | 0.8 | mA |  |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = REFUP | 0.375 | 0.55 | 0.825 | mA | ● |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = MEASURE | 0.65 | 0.95 | 1.35 | mA |  |
| V⁺ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{VP}$ | State: Core = MEASURE | 0.6 | 0.95 | 1.4 | mA | ● |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = SLEEP, isoSPI = IDLE, $V_{REG}$ = 5V |  | 3.1 | 6 | µA |  |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = SLEEP, isoSPI = IDLE, $V_{REG}$ = 5V |  | 3.1 | 9 | µA | ● |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = STANDBY | 10 | 35 | 60 | µA |  |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = STANDBY | 6 | 35 | 65 | µA | ● |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = REFUP | 0.4 | 0.9 | 1.4 | mA |  |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = REFUP | 0.3 | 0.9 | 1.5 | mA | ● |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = MEASURE | 14 | 15 | 16 | mA |  |
| $V_{REG}$ Supply Current (See Figure 1: LTC6813-1 Operation State Diagram) | $I_{REG(CORE)}$ | State: Core = MEASURE | 13.5 | 15 | 16.5 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 0, $R_{B1}$ + $R_{B2}$ = 2k, READY | 3.6 | 4.5 | 5.2 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 0, $R_{B1}$ + $R_{B2}$ = 2k, ACTIVE | 5.6 | 6.8 | 8.1 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 1, $R_{B1}$ + $R_{B2}$ = 2k, READY | 4.0 | 5.2 | 6.5 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 1, $R_{B1}$ + $R_{B2}$ = 2k, ACTIVE | 7.0 | 8.5 | 10.5 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 0, $R_{B1}$ + $R_{B2}$ = 20k, READY | 1.0 | 1.8 | 2.4 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 0, $R_{B1}$ + $R_{B2}$ = 20k, ACTIVE | 1.3 | 2.3 | 3.3 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 1, $R_{B1}$ + $R_{B2}$ = 20k, READY | 1.6 | 2.5 | 3.5 | mA | ● |
| Additional $V_{REG}$ Supply Current if isoSPI in READY/ACTIVE States Note: ACTIVE State Current Assumes $t_{CLK}$ = 1µs, (Note 3) | $I_{REG(isoSPI)}$ | ISOMD = 1, $R_{B1}$ + $R_{B2}$ = 20k, ACTIVE | 1.8 | 3.1 | 4.8 | mA | ● |
| $V^{+}$ Supply Voltage |  | TME Specifications Met | 16 | 60 | 90 | V | ● |
| $V^{+}$ to C18 Voltage |  | TME Specifications Met | −0.3 |  |  | V | ● |
| $V^{+}$ to C12 Voltage |  | TME Specifications Met |  |  | 40 | V | ● |
| C13 Voltage |  | TME Specifications Met | 2.5 |  |  | V | ● |
| C7 Voltage |  | TME Specifications Met | 1 |  |  | V | ● |
| $V_{REG}$ Supply Voltage | $V_{REG}$ | TME Supply Rejection < 1mV/V | 4.5 | 5 | 5.5 | V | ● |
| DRIVE Output Voltage |  | Sourcing 1µA | 5.4 | 5.7 | 5.9 | V |  |
| DRIVE Output Voltage |  | Sourcing 1µA | 5.2 | 5.7 | 6.1 | V | ● |
| DRIVE Output Voltage |  | Sourcing 500µA | 5.1 | 5.7 | 6.1 | V | ● |
| Digital Supply Voltage | $V_{REGD}$ |  | 2.7 | 3 | 3.6 | V | ● |
| Discharge Switch ON Resistance |  | $V_{CELL}$ = 3.6V |  | 4 | 10 | Ω | ● |
| Thermal Shutdown Temperature |  |  |  | 150 |  | °C |  |
| Watch Dog Timer Pin Low | $V_{OL(WDT)}$ | WDT Pin Sinking 4mA |  |  | 0.4 | V | ● |
| General Purpose I/O Pin Low | $V_{OL(GPIO)}$ | GPIO Pin Sinking 4mA (Used as Digital Output) |  |  | 0.4 | V | ● |
| **ADC Timing Specifications** |  |  |  |  |  |  |  |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Normal Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 18 Cells | 1743 | 2343 | 2488 | µs | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Normal Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 3 Cells | 303 | 407 | 432 | µs | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Normal Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 18 Cells and 2 GPIO Inputs | 2337 | 3140 | 3335 | µs | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Filtered Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 18 Cells | 150.0 | 201.3 | 213.8 | ms | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Filtered Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 3 Cells | 25.0 | 33.6 | 35.7 | ms | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Filtered Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 18 Cells and 2 GPIO Inputs | 200.0 | 268.5 | 285.1 | ms | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Fast Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 18 Cells | 834 | 1121 | 1191 | µs | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Fast Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 3 Cells | 151 | 203 | 215 | µs | ● |
| Measurement + Calibration Cycle Time When Starting from the REFUP State in Fast Mode | $t_{CYCLE}$ (Figure 3, Figure 4, Figure 6) | Measure 18 Cells and 2 GPIO Inputs | 1124 | 1511 | 1605 | µs | ● |
| Skew Time. The Time Difference Between Cell 18 and GPIO1 Measurements, Command = ADCVAX | $t_{SKEW1}$ (Figure 6) | Fast Mode | 144 | 194 | 206 | µs | ● |
| Skew Time. The Time Difference Between Cell 18 and GPIO1 Measurements, Command = ADCVAX | $t_{SKEW1}$ (Figure 6) | Normal Mode | 404 | 543 | 577 | µs | ● |
| Skew Time. The Time Difference Between Cell 18 and Cell 1 Measurements, Command = ADCV | $t_{SKEW2}$ (Figure 3) | Fast Mode | 174 | 233 | 248 | µs | ● |
| Skew Time. The Time Difference Between Cell 18 and Cell 1 Measurements, Command = ADCV | $t_{SKEW2}$ (Figure 3) | Normal Mode | 500 | 670 | 711 | µs | ● |
| Regulator Start-Up Time | $t_{WAKE}$ | $V_{REG}$ Generated from DRIVE Pin (Figure 32) |  | 200 | 400 | µs | ● |
| Watchdog or Discharge Timer | $t_{SLEEP}$ (Figure 26) | DTEN Pin = 0 or DCTO[3:0] = 0000 | 1.8 | 2 | 2.2 | sec | ● |
| Watchdog or Discharge Timer | $t_{SLEEP}$ (Figure 26) | DTEN Pin = 1 and DCTO[3:0] ≠ 0000 | 0.5 |  | 120 | min |  |
| Reference Wake-Up Time.  Added to $t_{CYCLE}$ Time When Starting from the STANDBY State. $t_{REFUP}$ = 0 When Starting from Other States. | $t_{REFUP}$ Figure 3 for example) | $t_{REFUP}$ is Independent of the Number of Channels Measured and the ADC Mode | 2.7 | 3.5 | 4.4 | ms | ● |
| ADC Clock Frequency | $f_{S}$ |  |  | 3.3 |  | MHz |  |
| **SPI Interface DC Specifications** |  |  |  |  |  |  |  |
| SPI Pin Digital Input Voltage High | $V_{IH(SPI)}$ | Pins CSB, SCK, SDI | 2.3 |  |  | V | ● |
| SPI Pin Digital Input Voltage Low | $V_{IL(SPI)}$ | Pins CSB, SCK, SDI |  |  | 0.8 | V | ● |
| Configuration Pin Digital Input Voltage High | $V_{IH(CFG)}$ | Pins ISOMD, DTEN, GPIO1 to GPIO9 | 2.7 |  |  | V | ● |
| Configuration Pin Digital Input Voltage Low | $V_{IL(CFG)}$ | Pins ISOMD, DTEN, GPIO1 to GPIO9 |  |  | 1.2 | V | ● |
| Digital Input Current | $I_{LEAK(DIG)}$ | Pins CSB, SCK, SDI, ISOMD, DTEN |  |  | ±1 | µA | ● |
| Digital Output Low | $V_{OL(SDO)}$ | Pin SDO Sinking 1mA |  |  | 0.3 | V | ● |
| **isoSPI DC Specifications (See Figure 17)** |  |  |  |  |  |  |  |
| Voltage on IBIAS Pin | $V_{BIAS}$ | READY/ACTIVE State | 1.9 | 2.0 | 2.1 | V | ● |
| Voltage on IBIAS Pin | $V_{BIAS}$ | IDLE State |  | 0 |  | V |  |
| Isolated Interface Bias Current | $I_{B}$ | $R_{BIAS}$ = 2k to 20k | 0.1 |  | 1.0 | mA | ● |
| Isolated Interface Current Gain | $A_{IB}$ | $V_{A}$ = ≤ 1.6V, $I_{B}$ = 1mA | 18 | 20 | 22 | mA/mA | ● |
| Isolated Interface Current Gain | $A_{IB}$ | $V_{A}$ = ≤ 1.6V, $I_{B}$ = 0.1mA | 18 | 20 | 24.5 | mA/mA | ● |
| Transmitter Pulse Amplitude | $V_{A}$ | $V_{A}$ = \|$V_{IP}$ − $V_{IM}$\| |  |  | 1.6 | V | ● |
| Threshold-Setting Voltage on ICMP Pin | $V_{ICMP}$ | $V_{TCMP}$ = $A_{TCMP}$ • $V_{ICMP}$ | 0.2 |  | 1.5 | V | ● |
| Input Leakage Current on ICMP Pin | $I_{LEAK(ICMP)}$ | $V_{ICMP}$ = 0V to $V_{REG}$ |  |  | ±1 | µA | ● |
| Leakage Current on IP and IM Pins | $I_{LEAK(IP/IM)}$ | IDLE State, $V_{IP}$ or $V_{IM}$,  0V to $V_{REG}$ |  |  | ±1 | µA | ● |
| Receiver Comparator Threshold Voltage Gain | $A_{TCMP}$ | $V_{CM}$ = $V_{REG}$/2 to $V_{REG}$ − 0.2V, $V_{ICMP}$ = 0.2V to 1.5V | 0.4 | 0.5 | 0.6 | V/V | ● |
| Receiver Common Mode Bias | $V_{CM}$ | IP/IM Not Driving |  | ($V_{REG}$ − $V_{ICMP}$/3 − 167mV) |  | V |  |
| Receiver Input Resistance | $R_{IN}$ | Single-Ended to IPA, IMA, IPB, IMB | 26 | 35 | 45 | kΩ | ● |
| **isoSPI Idle/Wake-Up Specifications (See Figure 26)** |  |  |  |  |  |  |  |
| Differential Wake-Up Voltage | $V_{WAKE}$ | $t_{DWELL}$ = 240ns | 200 |  |  | mV | ● |
| Dwell Time at $V_{WAKE}$ Before Wake Detection | $t_{DWELL}$ | $V_{WAKE}$ = 200mV | 240 |  |  | ns | ● |
| Start-Up Time After Wake Detection | $t_{READY}$ |  |  |  | 10 | µs | ● |
| Idle Timeout Duration | $t_{IDLE}$ |  | 4.3 | 5.5 | 6.7 | ms | ● |
| **isoSPI Pulse Timing Specifications (See Figure 22)** |  |  |  |  |  |  |  |
| Chip-Select Half-Pulse Width | $t_{1/2PW(CS)}$ | Transmitter | 120 | 150 | 180 | ns | ● |
| Chip-Select Signal Filter | $t_{FILT(CS)}$ | Receiver | 70 | 90 | 110 | ns | ● |
| Chip-Select Pulse Inversion Delay | $t_{INV(CS)}$ | Transmitter | 120 | 155 | 190 | ns | ● |
| Chip-Select Valid Pulse Window | $t_{WNDW(CS)}$ | Receiver | 220 | 270 | 330 | ns | ● |
| Data Half-Pulse Width | $t_{1/2PW(D)}$ | Transmitter | 40 | 50 | 60 | ns | ● |
| Data Signal Filter | $t_{FILT(D)}$ | Receiver | 10 | 25 | 35 | ns | ● |
| Data Pulse Inversion Delay | $t_{INV(D)}$ | Transmitter | 40 | 55 | 65 | ns | ● |
| Data Valid Pulse Window | $t_{WNDW(D)}$ | Receiver | 70 | 90 | 110 | ns | ● |
| **SPI Timing Requirements (See Figure 16 and Figure 25)** |  |  |  |  |  |  |  |
| SCK Period | $t_{CLK}$ | (Note 4) | 1 |  |  | µs | ● |
| SDI Setup Time before SCK Rising Edge | $t_{1}$ |  | 25 |  |  | ns | ● |
| SDI Hold Time after SCK Rising Edge | $t_{2}$ |  | 25 |  |  | ns | ● |
| SCK Low | $t_{3}$ | $t_{CLK}$ = $t_{3}$ + $t_{4}$ ≥ 1µs | 200 |  |  | ns | ● |
| SCK High | $t_{4}$ | $t_{CLK}$ = $t_{3}$ + $t_{4}$ ≥ 1µs | 200 |  |  | ns | ● |
| CSB Rising Edge to CSB Falling Edge | $t_{5}$ |  | 0.65 |  |  | µs | ● |
| SCK Rising Edge to CSB Rising Edge | $t_{6}$ | (Note 4) | 0.8 |  |  | µs | ● |
| CSB Falling Edge to SCK Rising Edge | $t_{7}$ | (Note 4) | 1 |  |  | µs | ● |
| **isoSPI Timing Specifications (See Figure 25)** |  |  |  |  |  |  |  |
| SCK Falling Edge to SDO Valid | $t_{8}$ | (Note 5) |  |  | 60 | ns | ● |
| SCK Rising Edge to Short ±1 Transmit | $t_{9}$ |  |  |  | 50 | ns | ● |
| CSB Transition to Long ±1 Transmit | $t_{10}$ |  |  |  | 60 | ns | ● |
| CSB Rising Edge to SDO Rising | $t_{11}$ | (Note 5) |  |  | 200 | ns | ● |
| Data Return Delay | $t_{RTN}$ |  | 325 | 375 | 425 | ns | ● |
| Chip-Select Daisy-Chain Delay | $t_{DSY(CS)}$ |  |  | 120 | 180 | ns | ● |
| Data Daisy-Chain Delay | $t_{DSY(D)}$ |  | 200 | 250 | 300 | ns | ● |
| Data Daisy-Chain Lag (vs Chip-Select) | $t_{LAG}$ | = [$t_{DSY(D)}$ + $t_{1/2PW(D)}$] − [$t_{DSY(CS)}$ + $t_{1/2PW(CS)}$] | 0 | 35 | 70 | ns | ● |
| Chip-Select High-to-Low Pulse Governor | $t_{5(GOV)}$ |  | 0.6 |  | 0.82 | µs | ● |
| Data to Chip-Select Pulse Governor | $t_{6(GOV)}$ |  | 0.8 |  | 1.05 | µs | ● |
| isoSPI Port Reversal Blocking Window | $t_{BLOCK}$ |  | 2 |  | 10 | µs | ● |

*OVERTEMP: ● marks a limit specified over the full operating temperature range; a blank cell means the limit is specified at $T_{A}$ = 25°C only.*

- **Note 1:** Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.

- **Note 2:** The ADC specifications are guaranteed by the Total Measurement Error specification.

- **Note 3:** The ACTIVE state current is calculated from DC measurements. The ACTIVE state current is the additional average supply current into $V_{REG}$ when there is continuous 1MHz communications on the isoSPI ports with 50% data 1's and 50% data 0's. Slower clock rates reduce the supply current. See Applications Information section for additional details.

- **Note 4:** These timing specifications are dependent on the delay through the cable, and include allowances for 50ns of delay each direction. 50ns corresponds to 10m of CAT5 cable (which has a velocity of propagation of 66% the speed of light). Use of longer cables would require derating these specs by the amount of additional delay.

- **Note 5:** These specifications do not include rise or fall time of SDO. While fall time (typically 5ns due to the internal pull-down transistor) is not a concern, rising-edge transition time $t_{RISE}$ is dependent on the pull-up resistance and load capacitance on the SDO pin. The time constant must be chosen such that SDO meets the setup time requirements of the MCU.

### TYPICAL PERFORMANCE CHARACTERISTICS
<!-- pages: 9-15 -->

68131 G01

68131 G04

68131 G07

$T_{A}$ = 25°C, unless otherwise noted.

68131 G02

68131 G05

68131 G03

68131 G06

68131 G16

$T_{A}$ = 25°C, unless otherwise noted.

68131 G14

68131 G17

68131 G15

68131 G18

68131 G19

68131 G22

68131 G25

$T_{A}$ = 25°C, unless otherwise noted.

68131 G23

68131 G26

68131 G21

68131 G27

$T_{A}$ = 25°C, unless otherwise noted.

68131 G37

isoSPI Current (ACTIVE) vs isoSPI Clock Frequency

$T_{A}$ = 25°C, unless otherwise noted.

68131 G44

68131 G39

isoSPI Current (READY) vs Temperature

68131 G42

68131 G45

isoSPI Driver Current Gain (Port A/Port B) vs IBIAS Current

68131 G46

$T_{A}$ = 25°C, unless otherwise noted.

isoSPI Driver Common Mode Voltage (Port A/Port B) vs Pulse Amplitude

isoSPI Driver Current Gain (Port A/Port B) vs Temperature

isoSPI Comparator Threshold Gain (Port A/Port B) vs Receiver Common Mode

isoSPI Comparator Threshold Gain (Port A/Port B) vs Temperature

68131 G47

isoSPI Comparator Threshold Gain (Port A/Port B) vs ICMP Voltage

![Measurement Error vs Temperature](ltc6813-1/figures/ltc6813-1-f006.png)

*Measurement Error vs Temperature*

Digitized data: [measurement-error-vs-temperature.csv](ltc6813-1/curves/measurement-error-vs-temperature.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Error vs Input, Fast Mode](ltc6813-1/figures/ltc6813-1-f007.png)

*Measurement Error vs Input, Fast Mode*

Digitized data: [measurement-error-vs-input-fast-mode.csv](ltc6813-1/curves/measurement-error-vs-input-fast-mode.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Noise vs Input, Fast Mode](ltc6813-1/figures/ltc6813-1-f008.png)

*Measurement Noise vs Input, Fast Mode*

Digitized data: [measurement-noise-vs-input-fast-mode.csv](ltc6813-1/curves/measurement-noise-vs-input-fast-mode.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Error vs Input, Normal Mode](ltc6813-1/figures/ltc6813-1-f009.png)

*Measurement Error vs Input, Normal Mode*

Digitized data: [measurement-error-vs-input-normal-mode.csv](ltc6813-1/curves/measurement-error-vs-input-normal-mode.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Noise vs Input, Normal Mode](ltc6813-1/figures/ltc6813-1-f010.png)

*Measurement Noise vs Input, Normal Mode*

Digitized data: [measurement-noise-vs-input-normal-mode.csv](ltc6813-1/curves/measurement-noise-vs-input-normal-mode.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Gain Error Thermal Hysteresis, Hot](ltc6813-1/figures/ltc6813-1-f011.png)

*Measurement Gain Error Thermal Hysteresis, Hot*

Digitized data: [measurement-gain-error-thermal-hysteresis-hot.csv](ltc6813-1/curves/measurement-gain-error-thermal-hysteresis-hot.csv) (x: ppm; y: parts) — values read off the printed plot by the digitizer, not published data.

![Measurement Error vs Input, Filtered Mode](ltc6813-1/figures/ltc6813-1-f012.png)

*Measurement Error vs Input, Filtered Mode*

Digitized data: [measurement-error-vs-input-filtered-mode.csv](ltc6813-1/curves/measurement-error-vs-input-filtered-mode.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Noise vs Input, Filtered Mode](ltc6813-1/figures/ltc6813-1-f013.png)

*Measurement Noise vs Input, Filtered Mode*

Digitized data: [measurement-noise-vs-input-filtered-mode.csv](ltc6813-1/curves/measurement-noise-vs-input-filtered-mode.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Gain Error Thermal Hysteresis, Cold](ltc6813-1/figures/ltc6813-1-f014.png)

*Measurement Gain Error Thermal Hysteresis, Cold*

Digitized data: [measurement-gain-error-thermal-hysteresis-cold.csv](ltc6813-1/curves/measurement-gain-error-thermal-hysteresis-cold.csv) (x: ppm; y: ) — values read off the printed plot by the digitizer, not published data.

![Measurement Error Due to IR Reflow](ltc6813-1/figures/ltc6813-1-f015.png)

*Measurement Error Due to IR Reflow*

Digitized data: [measurement-error-due-to-ir-reflow.csv](ltc6813-1/curves/measurement-error-due-to-ir-reflow.csv) (x: ppm; y: parts) — values read off the printed plot by the digitizer, not published data.

![Measurement Error vs V+](ltc6813-1/figures/ltc6813-1-f016.png)

*Measurement Error vs V+*

Digitized data: [measurement-error-vs-v.csv](ltc6813-1/curves/measurement-error-vs-v.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Error Due to a VREG AC Disturbance](ltc6813-1/figures/ltc6813-1-f017.png)

*Measurement Error Due to a $V_{REG}$ AC Disturbance*

Digitized data: [measurement-error-due-to-a-vreg-ac-disturbance.csv](ltc6813-1/curves/measurement-error-due-to-a-vreg-ac-disturbance.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Noise Filter Response](ltc6813-1/figures/ltc6813-1-f019.png)

*Noise Filter Response*

Digitized data: [noise-filter-response.csv](ltc6813-1/curves/noise-filter-response.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Top Cell Measurement Error vs V +](ltc6813-1/figures/ltc6813-1-f020.png)

*Top Cell Measurement Error vs $V^{+}$*

Digitized data: [top-cell-measurement-error-vs-v.csv](ltc6813-1/curves/top-cell-measurement-error-vs-v.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Error Due to a V + AC Disturbance](ltc6813-1/figures/ltc6813-1-f021.png)

*Measurement Error Due to a $V^{+}$ AC Disturbance*

Digitized data: [measurement-error-due-to-a-v-ac-disturbance.csv](ltc6813-1/curves/measurement-error-due-to-a-v-ac-disturbance.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Measurement Error vs V REG](ltc6813-1/figures/ltc6813-1-f022.png)

*Measurement Error vs $V_{REG}$>*

Digitized data: [measurement-error-vs-v-reg.csv](ltc6813-1/curves/measurement-error-vs-v-reg.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Error vs Common Mode Voltage](ltc6813-1/figures/ltc6813-1-f023.png)

*Measurement Error vs Common Mode Voltage*

Digitized data: [measurement-error-vs-common-mode-voltage.csv](ltc6813-1/curves/measurement-error-vs-common-mode-voltage.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Measurement Error CMRR vs Frequency](ltc6813-1/figures/ltc6813-1-f024.png)

*Measurement Error CMRR vs Frequency*

Digitized data: [measurement-error-cmrr-vs-frequency.csv](ltc6813-1/curves/measurement-error-cmrr-vs-frequency.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Cell Measurement Error Range vs Input RC Values](ltc6813-1/figures/ltc6813-1-f025.png)

*Cell Measurement Error Range vs Input RC Values*

Digitized data: [cell-measurement-error-range-vs-input-rc-values.csv](ltc6813-1/curves/cell-measurement-error-range-vs-input-rc-values.csv) (x: Ω; y: mV) — values read off the printed plot by the digitizer, not published data.

![Sleep Supply Current vs V +](ltc6813-1/figures/ltc6813-1-f026.png)

*Sleep Supply Current vs $V^{+}$*

Digitized data: [sleep-supply-current-vs-v.csv](ltc6813-1/curves/sleep-supply-current-vs-v.csv) (x: V; y: uA) — values read off the printed plot by the digitizer, not published data.

![Measure Supply Current vs V +](ltc6813-1/figures/ltc6813-1-f027.png)

*Measure Supply Current vs $V^{+}$*

Digitized data: [measure-supply-current-vs-v.csv](ltc6813-1/curves/measure-supply-current-vs-v.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![GPIO Measurement Error vs Input RC Values](ltc6813-1/figures/ltc6813-1-f028.png)

*GPIO Measurement Error vs Input RC Values*

Digitized data: [gpio-measurement-error-vs-input-rc-values.csv](ltc6813-1/curves/gpio-measurement-error-vs-input-rc-values.csv) (x: Ω; y: mV) — values read off the printed plot by the digitizer, not published data.

![Standby Supply Current vs V +](ltc6813-1/figures/ltc6813-1-f029.png)

*Standby Supply Current vs $V^{+}$*

Digitized data: [standby-supply-current-vs-v.csv](ltc6813-1/curves/standby-supply-current-vs-v.csv) (x: V; y: µA) — values read off the printed plot by the digitizer, not published data.

![VREF1 vs Temperature](ltc6813-1/figures/ltc6813-1-f030.png)

*$V_{REF1}$ vs Temperature*

Digitized data: [vref1-vs-temperature.csv](ltc6813-1/curves/vref1-vs-temperature.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![Measurement Time vs Temperature](ltc6813-1/figures/ltc6813-1-f031.png)

*Measurement Time vs Temperature*

Digitized data: [measurement-time-vs-temperature.csv](ltc6813-1/curves/measurement-time-vs-temperature.csv) (x: °C; y: ms) — values read off the printed plot by the digitizer, not published data.

![REFUP Supply Current vs V +](ltc6813-1/figures/ltc6813-1-f032.png)

*REFUP Supply Current vs $V^{+}$*

Digitized data: [refup-supply-current-vs-v.csv](ltc6813-1/curves/refup-supply-current-vs-v.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![VREF2 vs Temperature](ltc6813-1/figures/ltc6813-1-f033.png)

*$V_{REF2}$ vs Temperature*

Digitized data: [vref2-vs-temperature.csv](ltc6813-1/curves/vref2-vs-temperature.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![VREF2 VREG Line Regulation](ltc6813-1/figures/ltc6813-1-f129.png)

*$V_{REF2}$ $V_{REG}$ Line Regulation*

Digitized data: [vref2-vreg-line-regulation.csv](ltc6813-1/curves/vref2-vreg-line-regulation.csv) (x: V; y: ppm) — values read off the printed plot by the digitizer, not published data.

![VREF2 V+ Line Regulation](ltc6813-1/figures/ltc6813-1-f130.png)

*$V_{REF2}$ $V^{+}$ Line Regulation*

Digitized data: [vref2-v-line-regulation.csv](ltc6813-1/curves/vref2-v-line-regulation.csv) (x: V; y: ppm) — values read off the printed plot by the digitizer, not published data.

![VREF2 Load Regulation](ltc6813-1/figures/ltc6813-1-f131.png)

*$V_{REF2}$ Load Regulation*

Digitized data: [vref2-load-regulation.csv](ltc6813-1/curves/vref2-load-regulation.csv) (x: mA; y: ppm) — values read off the printed plot by the digitizer, not published data.

![VREF2 Thermal Hysteresis, Hot](ltc6813-1/figures/ltc6813-1-f132.png)

*$V_{REF2}$ Thermal Hysteresis, Hot*

Digitized data: [vref2-thermal-hysteresis-hot.csv](ltc6813-1/curves/vref2-thermal-hysteresis-hot.csv) (x: ppm; y: parts) — values read off the printed plot by the digitizer, not published data.

![VREF2 Thermal Hysteresis, Cold](ltc6813-1/figures/ltc6813-1-f133.png)

*$V_{REF2}$ Thermal Hysteresis, Cold*

Digitized data: [vref2-thermal-hysteresis-cold.csv](ltc6813-1/curves/vref2-thermal-hysteresis-cold.csv) (x: ppm; y: parts) — values read off the printed plot by the digitizer, not published data.

![VREF2 Change Due to IR Reflow](ltc6813-1/figures/ltc6813-1-f134.png)

*$V_{REF2}$ Change Due to IR Reflow*

Digitized data: [vref2-change-due-to-ir-reflow.csv](ltc6813-1/curves/vref2-change-due-to-ir-reflow.csv) (x: ppm; y: parts) — values read off the printed plot by the digitizer, not published data.

![VDRIVE V+ Line Regulation](ltc6813-1/figures/ltc6813-1-f135.png)

*$V_{DRIVE}$ $V^{+}$ Line Regulation*

Digitized data: [vdrive-v-line-regulation.csv](ltc6813-1/curves/vdrive-v-line-regulation.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![VDRIVE vs Temperature](ltc6813-1/figures/ltc6813-1-f136.png)

*$V_{DRIVE}$ vs Temperature*

Digitized data: [vdrive-vs-temperature.csv](ltc6813-1/curves/vdrive-vs-temperature.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![VDRIVE Load Regulation](ltc6813-1/figures/ltc6813-1-f137.png)

*$V_{DRIVE}$ Load Regulation*

Digitized data: [vdrive-load-regulation.csv](ltc6813-1/curves/vdrive-load-regulation.csv) (x: mA; y: mV) — values read off the printed plot by the digitizer, not published data.


![Discharge Switch On-Resistance vs Cell Voltage](ltc6813-1/figures/ltc6813-1-f035.png)

*Discharge Switch On-Resistance vs Cell Voltage*

Digitized data: [discharge-switch-on-resistance-vs-cell-voltage.csv](ltc6813-1/curves/discharge-switch-on-resistance-vs-cell-voltage.csv) (x: V; y: Ω) — values read off the printed plot by the digitizer, not published data.

![VREF1  and V REF2  Power-Up](ltc6813-1/figures/ltc6813-1-f036.png)

*$V_{REF1}$ and $V_{REF2}$ Power-Up*

![Clock Frequency](ltc6813-1/figures/ltc6813-1-f037.png)

*Clock Frequency*

Digitized data: [clock-frequency.csv](ltc6813-1/curves/clock-frequency.csv) (x: kHz; y: mA) — values read off the printed plot by the digitizer, not published data.

![Internal Die Temperature Increase vs Discharge Current](ltc6813-1/figures/ltc6813-1-f038.png)

*Internal Die Temperature Increase vs Discharge Current*

Digitized data: [internal-die-temperature-increase-vs-discharge-current.csv](ltc6813-1/curves/internal-die-temperature-increase-vs-discharge-current.csv) (x: mA/CELL; y: °C) — values read off the printed plot by the digitizer, not published data.

![VREG  and V DRIVE  Power-Up](ltc6813-1/figures/ltc6813-1-f039.png)

*$V_{REG}$ and $V_{DRIVE}$ Power-Up*

![IBIAS Voltage vs Temperature](ltc6813-1/figures/ltc6813-1-f040.png)

*IBIAS Voltage vs Temperature*

Digitized data: [ibias-voltage-vs-temperature.csv](ltc6813-1/curves/ibias-voltage-vs-temperature.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![Internal Die Temperature Measurement Error vs Temperature](ltc6813-1/figures/ltc6813-1-f041.png)

*Internal Die Temperature Measurement Error vs Temperature*

Digitized data: [internal-die-temperature-measurement-error-vs-temperature.csv](ltc6813-1/curves/internal-die-temperature-measurement-error-vs-temperature.csv) (x: °C; y: °C) — values read off the printed plot by the digitizer, not published data.

![Temperature](ltc6813-1/figures/ltc6813-1-f042.png)

*isoSPI Current (READY) vs Temperature*

Digitized data: [temperature.csv](ltc6813-1/curves/temperature.csv) (x: °C; y: ISOMD = V-) — values read off the printed plot by the digitizer, not published data.

![IBIAS Voltage Load Regulation](ltc6813-1/figures/ltc6813-1-f043.png)

*IBIAS Voltage Load Regulation*

Digitized data: [ibias-voltage-load-regulation.csv](ltc6813-1/curves/ibias-voltage-load-regulation.csv) (x: µA; y: V) — values read off the printed plot by the digitizer, not published data.

![(Port A/Port B) vs IBIAS Current](ltc6813-1/figures/ltc6813-1-f044.png)

*isoSPI Driver Current Gain (Port A/Port B) vs IBIAS Current*

Digitized data: [port-a-port-b-vs-ibias-current.csv](ltc6813-1/curves/port-a-port-b-vs-ibias-current.csv) (x: µA; y: mA) — values read off the printed plot by the digitizer, not published data.

![(Port A/Port B) vs Temperature](ltc6813-1/figures/ltc6813-1-f045.png)

*isoSPI Driver Current Gain (Port A/Port B) vs Temperature*

Digitized data: [port-a-port-b-vs-temperature.csv](ltc6813-1/curves/port-a-port-b-vs-temperature.csv) (x: °C; y: IB = 100uA) — values read off the printed plot by the digitizer, not published data.

![Gain (Port A/Port B) vs Receiver Common Mode](ltc6813-1/figures/ltc6813-1-f046.png)

*isoSPI Comparator Threshold Gain (Port A/Port B) vs Receiver Common Mode*

Digitized data: [gain-port-a-port-b-vs-receiver-common-mode.csv](ltc6813-1/curves/gain-port-a-port-b-vs-receiver-common-mode.csv) (x: V; y: V/V) — values read off the printed plot by the digitizer, not published data.

![Gain (Port A/Port B) vs Temperature](ltc6813-1/figures/ltc6813-1-f047.png)

*isoSPI Comparator Threshold Gain (Port A/Port B) vs Temperature*

Digitized data: [gain-port-a-port-b-vs-temperature.csv](ltc6813-1/curves/gain-port-a-port-b-vs-temperature.csv) (x: °C; y: V/V) — values read off the printed plot by the digitizer, not published data.

![Voltage (Port A/Port B) vs Pulse Amplitude](ltc6813-1/figures/ltc6813-1-f048.png)

*isoSPI Driver Common Mode Voltage (Port A/Port B) vs Pulse Amplitude*

Digitized data: [voltage-port-a-port-b-vs-pulse-amplitude.csv](ltc6813-1/curves/voltage-port-a-port-b-vs-pulse-amplitude.csv) (x: V; y: IB = 100µA) — values read off the printed plot by the digitizer, not published data.

![Gain (Port A/Port B) vs ICMP Voltage](ltc6813-1/figures/ltc6813-1-f049.png)

*isoSPI Comparator Threshold Gain (Port A/Port B) vs ICMP Voltage*

Digitized data: [gain-port-a-port-b-vs-icmp-voltage.csv](ltc6813-1/curves/gain-port-a-port-b-vs-icmp-voltage.csv) (x: V; y: V/V) — values read off the printed plot by the digitizer, not published data.

![Typical Wake-Up Pulse Amplitude (Port A/Port B) vs Dwell Time](ltc6813-1/figures/ltc6813-1-f050.png)

*Typical Wake-Up Pulse Amplitude (Port A/Port B) vs Dwell Time*

Digitized data: [typical-wake-up-pulse-amplitude-port-a-port-b-vs-dwell-time.csv](ltc6813-1/curves/typical-wake-up-pulse-amplitude-port-a-port-b-vs-dwell-time.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

### PIN FUNCTIONS
<!-- pages: 15-16 -->

C0 to C18: Cell Inputs.

S1  to  S18: Balance Inputs/Outputs. 18 internal N-MOSFETs are connected between S(n) and C(n-1) for discharging cells.

$V^{+}$ : Positive Supply Pin.

$V^{-}$: Negative Supply Pins. The $V^{-}$ pins must be shorted together , external to the IC.

$V_{REF2}$ : Buffered 2nd Reference Voltage for Driving Multiple 10k Thermistors. Bypass with an external 1µF capacitor . $V_{REF1}$: ADC Reference Voltage. Bypass with an external 1µF capacitor . No DC loads allowed.

GPIO[1:9] : General Purpose I/O. Can be used as digital inputs or digital outputs, or as analog inputs with a measurement range from $V^{-}$ to 5V. GPIO[3:5] can be used as an $I^{2}C$ or SPI port.

DTEN: Discharge Timer Enable. Connect this pin to $V_{REG}$ to enable the Discharge Timer .

DRIVE: Connect the base of an NPN to this pin. Connect the collector to $V^{+}$ and the emitter to $V_{REG}$.

$V_{REG}$ : 5V  Regulator  Input.  Bypass  with  an  external 1µF capacitor .

ISOMD: Serial  Interface  Mode.  Connecting  ISOMD to $V_{REG}$ configures pins 53, 54, 61 and 62 of the LTC6813-1 for 2-wire isolated interface (isoSPI) mode. Connecting ISOMD  to  $V^{-}$ configures  the  LTC6813-1  for  4-wire SPI mode.

WDT: Watchdog Timer Output Pin. This is an open drain NMOS digital output. It can be left unconnected or connected with a 1M resistor to $V_{REG}$. If  the  LTC6813-1 does not receive a valid command within 2 seconds, the watchdog timer circuit will reset the LTC6813-1 and the WDT pin will go high impedance.

### Serial Port Pins
<!-- page: 15 -->

**Serial Port Pins** ([table-03-p15-pin.csv](ltc6813-1/tables/table-03-p15-pin.csv), p. 15)

| PORT | ISOMD = $V_{REG}$ | ISOMD = $V^{-}$ |
|---|---|---|
| PORT B (Pins 57, 58, 63 and 64) | IPB | IPB |
| PORT B (Pins 57, 58, 63 and 64) | IMB | IMB |
| PORT B (Pins 57, 58, 63 and 64) | ICMP | ICMP |
| PORT B (Pins 57, 58, 63 and 64) | IBIAS | IBIAS |
| PORT A (Pins 53, 54, 61 and 62) | (NC) | SDO |
| PORT A (Pins 53, 54, 61 and 62) | (NC) | SDI |
| PORT A (Pins 53, 54, 61 and 62) | IPA | SCK |
| PORT A (Pins 53, 54, 61 and 62) | IMA | CSB |

CSB,  SCK,  SDI,  SDO: 4-Wire Serial Peripheral Interface (SPI). Active low chip select (CSB), serial clock (SCK) and serial data in (SDI) are digital inputs. Serial data out (SDO) is an open drain NMOS output pin. SDO requires a 5k pull-up resistor .

IPA,  IMA: Isolated  2-Wire  Serial  Interface  Port  A. IPA (plus) and IMA (minus) are a differential input/output pair .

IPB,  IMB: Isolated  2-Wire  Serial  Interface  Port  B. IPB (plus) and IMB (minus) are a differential input/output pair .

IBIAS: Isolated Interface Current Bias. Tie IBIAS to $V^{-}$ through a resistor divider to set the interface output current level. When the isoSPI interface is enabled, the IBIAS pin voltage is 2V. The IPA/IMA or IPB/IMB output current drive is set to 20 times the current, $I_{B}$, sourced from the IBIAS pin.

ICMP: Isolated Interface Comparator Voltage Threshold Set. Tie this pin to the resistor divider between IBIAS and V to set the voltage threshold of the isoSPI receiver comparators. The comparator thresholds are set to half the voltage on the ICMP pin.

Exposed Pad: $V^{-}$.  The Exposed Pad must be soldered to PCB.

### BLOCK DIAGRAM
<!-- pages: 16-17 -->

![block diagram (p. 16)](ltc6813-1/figures/ltc6813-1-f051.png)

### IMPROVEMENTS FROM THE LTC6811-1
<!-- pages: 17-18 -->

The LTC6813-1 is an evolution of the LTC6811-1 design. The following table summarizes the feature changes and additions in the LTC6813-1.

**Improvements from the LTC6811-1 (Additional LTC6813-1 Features / Benefits / Relevant Data Sheet Section(s))** ([table-04-p17-data.csv](ltc6813-1/tables/table-04-p17-data.csv), p. 17)

| ADDITIONAL LTC6813-1 FEATURES | BENEFITS | RELEVANT DATA SHEET SECTION(S) |
|---|---|---|
| The LTC6813-1 Has 3 ADCs Operating Simultaneously vs 2 ADCs on LTC6811-1 | 3 Cells Can Be Measured During Each Conversion Cycle | ADC Operation |
| In Addition to the 3 ADC Digital Filters, There Is a 4th Filter Which Is Used for Redundancy | Checks That All Digital Filters are Free of Faults | ADC Conversion with Digital Redundancy for a description and PS[1:0] bits in Table 10 |
| Measure Cell 7 with ADC1 and ADC2 Simultaneously and then Measure Cell 13 with ADC2 and ADC3 Simultaneously Using the ADOL Command | Checks That ADC2 Is as Accurate as ADC1 and Also Checks That ADC3 Is as Accurate as ADC2 | Overlap Cell Measurement (ADOL Command) |
| A Monitoring Feature Can Be Enabled During the Discharge Timer. The Cell Balancing Can Be Automatically Terminated When Cell Voltages Reach a Programmable Undervoltage Threshold | Improved Cell Balancing | Discharge Timer Monitor |
| The Internal Discharge MOSFETs Can Provide 200mA of Balancing Current (80mA if the die temperature is over 95°C). The Balancing Current Is Independent of Cell Voltage | Faster Cell Balancing, Especially for Low Cell Voltages | Cell Balancing with Internal MOSFETs |
| The C0 Pin Voltage Is Allowed to Range Between 0V and 1V Without Affecting Total Measurement Error (TME) | C0 Does Not Have to Connect Directly to $V^{-}$ | Input Range in Electrical Characteristics |
| The MUTE and UNMUTE Commands Allow the Host to Turn Off/On the Discharge Pins (S Pins) Without Overwriting Register Values | Greater Control of Timing Between S Pins Turning Off and Cell Measurements | S Pin Muting |
| Auxiliary Measurements Have an Open-Wire Diagnostic Feature | Improved Fault Detection | Auxiliary Open Wire Check (AXOW Command) |
| Four Additional GPIO Pins Have Been Added for a Total of Nine | Increased Number of Temperature or Other Sensors That Can Be Measured | Auxiliary (GPIO) Measurements (ADAX Command) and Auxiliary Open Wire Check (AXOW Command) |
| A Daisy Chain of LTC6813-1s Can Operate in Both Directions (Both Ports Can Be Master or Slave) | Redundant Communication Path | Reversible isoSPI |

WRCFGA command, the Configuration Register Groups

### OPERATION
<!-- pages: 18-70 -->

### STATE DIAGRAM
<!-- page: 18 -->

The operation of the LTC6813-1 is divided into two separate sections: the Core circuit and the isoSPI circuit. Both sections have an independent set of operating states, as well as a shutdown timeout.

### CORE LTC6813-1 STATE DESCRIPTIONS
<!-- page: 18 -->

### SLEEP State
<!-- page: 18 -->

The references and ADCs are powered down. The watchdog timer (see Watchdog and Discharge Timer) has timed out. The discharge timer is either disabled or timed out. The supply currents are reduced to minimum levels. The isoSPI ports will be in the IDLE state. The DRIVE pin is 0V. All state machines are reset to their default states.

If a WAKE-UP signal is received (see Waking Up the Serial Interface), the LTC6813-1 will enter the STANDBY state.

### STANDBY State
<!-- page: 18 -->

The references and the ADCs are off. The watchdog timer and/or the discharge timer is running. The DRIVE pin powers the $V_{REG}$ pin to 5V through an external transistor .  (Alternatively, $V_{REG}$ can be powered by an external supply).

When a valid ADC command is received or the REFON bit is set to 1 in Configuration Register Group A, the IC pauses for $t_{REFUP}$ to allow for the references to power up and then enters either the REFUP or MEASURE state. Otherwise, if no valid commands are received for $t_{SLEEP}$, the IC returns to the SLEEP state if DTEN = 0 or enters the EXTENDED BALANCING state if DTEN = 1.

### REFUP State
<!-- page: 18 -->

To reach this state, the REFON bit in Configuration Register Group A must be set to 1 (using the WRCFGA command, see Table 36). The ADCs are off. The references are powered up so that the LTC6813-1 can initiate ADC conversions more quickly than from the STANDBY state.

When a valid ADC command is received, the IC goes to the MEASURE state to begin the conversion. Otherwise, the LTC6813-1 will return to the STANDBY state when the REFON bit is set to 0 (using WRCFGA command). If no valid commands are received for $t_{SLEEP}$, the IC returns to the SLEEP state if DTEN = 0 or enters the EXTENDED BALANCING state if DTEN = 1.

### MEASURE State
<!-- page: 18 -->

The LTC6813-1 performs ADC conversions in this state. The references and ADCs are powered up.

After ADC conversions are complete, the LTC6813-1 will transition to either the REFUP or STANDBY state, depending on the REFON bit. Additional ADC conversions can be initiated more quickly by setting REFON = 1 to take advantage of the REFUP state.

Note: Non-ADC commands do not cause a Core state transition. Only an ADC Conversion or diagnostic commands will place the Core in the MEASURE state.

![Figure 1. LTC6813-1 Operation State Diagram](ltc6813-1/figures/ltc6813-1-f053.png)

*Figure 1. LTC6813-1 Operation State Diagram*

### EXTENDED BALANCING State
<!-- page: 18 -->

The watchdog timer has timed out, but the discharge timer has not yet timed out (DTEN = 1). Discharge by PWM may be in progress. If the Discharge Timer Monitor is enabled then the LTC6813-1 will transition to the DTM MEASURE state every 30 seconds to measure the cell voltages. If a WAKE-UP signal is received, the LTC6813-1 will transition from EXTENDED BALANCING state to STANDBY state.

### Discharge Timer Monitor MEASURE State
<!-- page: 19 -->

The watchdog timer has timed out but background monitoring has been enabled (DTMEN = 1 in Configuration Register Group B). The LTC6813-1 enters this state from the EXTENDED BALANCING state once every 30 seconds to measure the cell voltages. The LTC6813-1 is in the highest core power state and an A/D conversion is in progress. If a WAKE-UP signal is received, the LTC6813-1 will transition from DTM MEASURE state to STANDBY state.

### isoSPI STATE DESCRIPTIONS
<!-- page: 19 -->

Note: The LTC6813-1 has two isoSPI ports (A and B), for daisy-chain communication.

### IDLE State
<!-- page: 19 -->

The isoSPI ports are powered down.

When isoSPI Port A or Port B receives a WAKE-UP signal (see Waking Up the Serial Interface), the isoSPI enters the READY state. This transition happens quickly (within $t_{READY}$) if the Core is in the STANDBY state. If the Core is in the SLEEP state when the isoSPI receives a WAKE-UP signal, then it transitions to the READY state within $t_{WAKE}$.

### READY State
<!-- page: 19 -->

The isoSPI port(s) are ready for communication. The serial interface current in this state depends on the status of the ISOMD pin and $R_{BIAS}$ = $R_{B1}$ + $R_{B2}$ (the external resistors tied to the IBIAS pin).

If there is no activity (i.e., no WAKE-UP signal) on Port A or Port B for greater than $t_{IDLE}$, the LTC6813-1 goes to the IDLE state. When the serial interface is transmitting or receiving data, the LTC6813-1 goes to the ACTIVE state.

### ACTIVE State
<!-- page: 19 -->

The LTC6813-1 is transmitting/receiving data using one or  both  of  the  isoSPI  ports.  The  serial  interface  consumes maximum power in this state. The supply current increases with clock frequency as the density of isoSPI pulses increases.

### POWER CONSUMPTION
<!-- page: 19 -->

The LTC6813-1 is powered via two pins: $V^{+}$ and $V_{REG}$. The $V^{+}$ input requires voltage greater than or equal to the top cell voltage minus 0.3V, and it provides power to the high voltage elements of the Core circuits. The $V_{REG}$ input requires 5V and provides power to the remaining Core circuits and the isoSPI circuitry. The $V_{REG}$ input can be powered through an external transistor , driven by the regulated DRIVE output pin. Alternatively, $V_{REG}$ can be powered by an external supply.

The power consumption varies according to the operational states. Table 1 and Table 2 provide equations to approximate the supply pin currents in each state. The $V^{+}$ pin current depends only on the Core state. However , the $V_{REG}$ pin current depends on both the Core state and isoSPI state, and can, therefore, be divided into two components. The isoSPI interface draws current only from the $V_{REG}$ pin.

![Equation as printed on page 19](ltc6813-1/figures/ltc6813-1-eq09.png)

$$I_{\mathrm{REG}} = I_{\mathrm{REG(CORE)}} + I_{\mathrm{REG(isoSPI)}}$$

In the SLEEP state, the $V_{REG}$ pin will draw approximately 3.1µA if powered by an external supply. Otherwise, the $V^{+}$ pin will supply the necessary current.

**Table 1. Core Supply Current** ([table-05-p20-data.csv](ltc6813-1/tables/table-05-p20-data.csv), p. 20)

| STATE | CONDITIONS | $I_{VP}$ | $I_{REG(CORE)}$ |
|---|---|---|---|
| SLEEP | $V_{REG}$ = 0V | 6.1µA | 0µA |
| SLEEP | $V_{REG}$ = 5V | 3µA | 3.1µA |
| STANDBY |  | 14µA | 35µA |
| REFUP |  | 550µA | 900µA |
| MEASURE |  | 950µA | 15mA |

**Table 2. isoSPI Supply Current Equations** ([table-06-p20-data.csv](ltc6813-1/tables/table-06-p20-data.csv), p. 20)

| isoSPI STATE | ISOMD CONNECTION | $I_{REG(isoSPI)}$ |
|---|---|---|
| IDLE | N/A | 0mA |
| READY | $V_{REG}$ | 2.2mA + 3 • $I_{B}$ |
| READY | $V^{-}$ | 1.5mA + 3 • $I_{B}$ |
| ACTIVE | $V_{REG}$ | Write: 2.5mA + (3 + 20 • 100ns/$t_{CLK}$) • $I_{B}$ |
| ACTIVE | $V_{REG}$ | Read: 2.5mA + (3 + 20 • (100ns • 1.5)/$t_{CLK}$) • $I_{B}$ |
| ACTIVE | $V^{-}$ | 1.8mA + (3 + 20 • 100ns/$t_{CLK}$) • $I_{B}$ |

### ADC OPERATION
<!-- page: 20 -->

There are three ADCs inside the LTC6813-1. The three ADCs operate simultaneously when measuring eighteen cells. Only one ADC is used to measure the general purpose inputs. The following discussion uses the term ADC to refer to one or all ADCs, depending on the operation being performed. The following discussion will refer to ADC1, ADC2 and ADC3 when it is necessary to distinguish between the three circuits, in timing diagrams, for example.

### ADC Modes
<!-- page: 20 -->

The ADCOPT bit (CFGAR0[0]) in Configuration Register Group A and the mode selection bits MD[1:0] in the conversion command together provide eight modes of operation  for  the  ADC  which  correspond  to  different oversampling ratios (OSR). The accuracy and timing of these modes are summarized in Table 3. In each mode, the ADC first measures the inputs, and then performs a calibration of each channel. The names of the modes are based on the -3dB bandwidth of the ADC measurement.

Mode 7kHz (Normal): In this mode, the ADC has high resolution and low TME (Total Measurement Error). This is considered the normal operating mode because of the optimum combination of speed and accuracy.

Mode 27kHz (Fast): In this mode, the ADC has maximum throughput but has some increase in TME (Total Measurement Error). So this mode is also referred to as the fast mode. The increase in speed comes from a reduction in the oversampling ratio. This results in an increase in noise and average measurement error .

Mode 26Hz (Filtered): In this mode, the ADC digital filter -3dB frequency is lowered to 26Hz by increasing the OSR. This mode is also referred to as the filtered mode due to its low -3dB frequency. The accuracy is similar to the 7kHz (Normal) mode with lower noise.

Modes 14kHz, 3kHz, 2kHz, 1kHz and 422Hz: Modes 14kHz, 3kHz, 2kHz, 1kHz and 422Hz provide additional options to set the ADC digital filter -3dB at 13.5kHz, 3.4kHz, 1.7kHz, 845Hz and 422Hz, respectively. The accuracy of the 14kHz mode is similar to the 27kHz (Fast) mode. The accuracy of 3kHz, 2kHz, 1kHz and 422Hz modes is similar to the 7kHz (Normal) mode.

The filter bandwidths and the conversion times for these modes are provided in Table 3 and Table 5. If the Core is in STANDBY state, an additional $t_{REFUP}$ time is required to power up the reference before beginning the ADC conversions. The reference can remain powered up between ADC conversions if the REFON bit in Configuration Register Group A is set to 1 so the Core is in REFUP state after a delay $t_{REFUP}$. Then, the subsequent ADC commands will  not  have  the  $t_{REFUP}$ delay  before  beginning  ADC conversions.

**Table 3. ADC Filter Bandwidth and Accuracy** ([table-07-p21-spec.csv](ltc6813-1/tables/table-07-p21-spec.csv), p. 21)

| MODE | –3dB FILTER BW | –40dB FILTER BW | TME SPEC AT 3.3V, 25°C | TME SPEC AT 3.3V, –40°C, 125°C |
|---|---|---|---|---|
| 27kHz (Fast Mode) | 27kHz | 84kHz | ±6mV | ±6mV |
| 14kHz | 13.5kHz | 42kHz | ±6mV | ±6mV |
| 7kHz (Normal Mode) | 6.8kHz | 21kHz | ±2.2mV | ±3.3mV |
| 3kHz | 3.4kHz | 10.5kHz | ±2.2mV | ±3.3mV |
| 2kHz | 1.7kHz | 5.3kHz | ±2.2mV | ±3.3mV |
| 1kHz | 845Hz | 2.6kHz | ±2.2mV | ±3.3mV |
| 422Hz | 422Hz | 1.3kHz | ±2.2mV | ±3.3mV |
| 26Hz (Filtered Mode) | 26Hz | 82Hz | ±2.2mV | ±3.3mV |

- Note: TME is the Total Measurement Error.

### ADC Range and Resolution
<!-- page: 21 -->

The C inputs and GPIO inputs have the same range and resolution. The ADC inside the LTC6813-1 has an approximate range from -0.82V to +5.73V. Negative readings are rounded to 0V. The format of the data is a 16-bit unsigned integer where the LSB represents 100µV. Therefore, a reading of 0x80E8 (33,000 decimal) indicates a measurement of 3.3V.

Delta-Sigma ADCs have quantization noise which depends on  the  input  voltage,  especially  at  low  oversampling ratios (OSR), such as in FAST mode. In some of the ADC modes, the quantization noise increases as the input voltage approaches the upper and lower limits of the ADC range. For example, the total measurement noise versus input voltage in normal and filtered modes is shown in Figure 2.

![Figure 2. Measurement Noise vs Input Voltage](ltc6813-1/figures/ltc6813-1-f054.png)

*Figure 2. Measurement Noise vs Input Voltage*

68131 F02

Digitized data: [measurement-noise-vs-input-voltage.csv](ltc6813-1/curves/measurement-noise-vs-input-voltage.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

The specified range of the ADC is 0V to 5V. In Table 4, the precision range of the ADC is arbitrarily defined as 0.5V to 4.5V. This is the range where the quantization noise is relatively constant even in the lower OSR modes (see Figure 2). Table 4 summarizes the total noise in this range for all eight ADC operating modes. Also shown is the noise free resolution. For example, 14-bit noise free resolution in normal mode implies that the top 14 bits will be noise free with a DC input, but that the 15th and 16th Least Significant Bits (LSB) will flicker .

### ADC Range vs Voltage Reference Value
<!-- page: 21 -->

Typical ADCs have a range which is exactly twice the value of the voltage reference, and the ADC measurement error is directly proportional to the error in the voltage reference. The LTC6813-1 ADC is not typical. The absolute value of $V_{REF1}$ is trimmed up or down to compensate for gain errors in the ADC. Therefore, the ADC Total Measurement Error (TME) specifications are superior to the $V_{REF1}$ specifications. For example, the 25°C specification of the Total Measurement Error when measuring 3.300V in 7kHz (Normal) mode is ±2.2mV and the 25°C specification for $V_{REF1}$ is 3.150V ± 150mV.

### Measuring Cell Voltages (ADCV Command)
<!-- page: 22 -->

The ADCV command initiates the measurement of the battery cell inputs, pins C0 through C18. This command has options to select the number of channels to measure and the ADC mode. See the section on Commands for the ADCV command format.

Figure 3 illustrates the timing of the ADCV command which measures all eighteen cells. After the receipt of the ADCV command to measure all 18 cells, ADC1 sequentially measures the bottom 6 cells. ADC2 measures the middle 6 cells and ADC3 measures the top 6 cells. After the cell measurements are complete, each channel is calibrated to remove any offset errors.

**Table 4. ADC Range and Resolution** ([table-08-p22-spec.csv](ltc6813-1/tables/table-08-p22-spec.csv), p. 22)

| MODE | FULL RANGE $[^{1}]$ | SPECIFIED RANGE | PRECISION RANGE $[^{2}]$ | LSB | FORMAT | MAX NOISE | NOISE FREE RESOLUTION $[^{3}]$ |
|---|---|---|---|---|---|---|---|
| 27kHz (Fast) | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±4 $mV_{P-P}$ | 10 Bits |
| 14kHz | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±1 $mV_{P-P}$ | 12 Bits |
| 7kHz (Normal) | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±250µ$V_{P-P}$ | 14 Bits |
| 3kHz | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±150µ$V_{P-P}$ | 14 Bits |
| 2kHz | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±100µ$V_{P-P}$ | 15 Bits |
| 1kHz | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±100µ$V_{P-P}$ | 15 Bits |
| 422Hz | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±100µ$V_{P-P}$ | 15 Bits |
| 26Hz (Filtered) | −0.8192V to 5.7344V | 0V to 5V | 0.5V to 4.5V | 100µV | Unsigned 16 Bits | ±50µ$V_{P-P}$ | 16 Bits |

- **Note 1:** Negative readings are rounded to 0V.
- **Note 2:** PRECISION RANGE is the range over which the noise is less than MAX NOISE.
- **Note 3:** NOISE FREE RESOLUTION is a measure of the noise level within the PRECISION RANGE.

![Figure 3. Timing for ADCV Command Measuring All 18 Cells](ltc6813-1/figures/ltc6813-1-f055.png)

*Figure 3. Timing for ADCV Command Measuring All 18 Cells*

Table 5 shows the conversion times for the ADCV command measuring all 18 cells. The total conversion time is given by $t_{6C}$ which indicates the end of the calibration step.

Figure 4 illustrates the timing of the ADCV command that measures only three cells.

**Table 5. Conversion and Synchronization Times for ADCV Command Measuring All 18 Cells in Different Modes** ([table-09-p23-data.csv](ltc6813-1/tables/table-09-p23-data.csv), p. 23)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{2M}$ | $t_{5M}$ | $t_{6M}$ | $t_{6C}$ | $t_{SKEW2}$ |
|---|---|---|---|---|---|---|---|
| **CONVERSION TIMES (IN µs)** |  |  |  |  |  |  |  |
| 27kHz | 0 | 58 | 104 | 244 | 291 | 1,121 | 233 |
| 14kHz | 0 | 87 | 163 | 390 | 466 | 1,296 | 379 |
| 7kHz | 0 | 145 | 279 | 681 | 815 | 2,343 | 670 |
| 3kHz | 0 | 261 | 512 | 1,263 | 1,513 | 3,041 | 1,252 |
| 2kHz | 0 | 494 | 977 | 2,426 | 2,909 | 4,437 | 2,415 |
| 1kHz | 0 | 960 | 1,908 | 4,753 | 5,702 | 7,230 | 4,742 |
| 422Hz | 0 | 1,890 | 3,770 | 9,408 | 11,287 | 12,816 | 9,397 |
| 26Hz | 0 | 29,818 | 59,624 | 149,044 | 178,851 | 201,325 | 149,033 |

![Figure 4. Timing for ADCV Command Measuring 3 Cells](ltc6813-1/figures/ltc6813-1-f056.png)

*Figure 4. Timing for ADCV Command Measuring 3 Cells*

Table 6 shows the conversion time for the ADCV command measuring only 3 cells. $t_{1C}$ indicates the total conversion time for this command.

**Table 6. Conversion Times for ADCV Command Measuring 3 Cells in Different Modes** ([table-10-p24-data.csv](ltc6813-1/tables/table-10-p24-data.csv), p. 24)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{1C}$ |
|---|---|---|---|
| **CONVERSION TIMES (IN µs)** |  |  |  |
| 27kHz | 0 | 58 | 203 |
| 14kHz | 0 | 87 | 232 |
| 7kHz | 0 | 145 | 407 |
| 3kHz | 0 | 261 | 523 |
| 2kHz | 0 | 494 | 756 |
| 1kHz | 0 | 960 | 1,221 |
| 422Hz | 0 | 1,890 | 2,152 |
| 26Hz | 0 | 29,818 | 33,570 |

### Under/Over Voltage Monitoring
<!-- page: 24 -->

Whenever the C inputs are measured, the results are compared to undervoltage and overvoltage thresholds stored in memory. If the reading of a cell is above the overvoltage limit, a bit in memory is set as a flag. Similarly, measurement results below the undervoltage limit cause a flag to be set. The overvoltage and undervoltage thresholds are stored in Configuration Register Group A. The flags are stored in Status Register Group B and Auxiliary Register Group D.

### Auxiliary (GPIO) Measurements (ADAX Command)
<!-- page: 24 -->

The ADAX command initiates the measurement of the GPIO inputs. This command has options to select which GPIO input to measure (GPIO1-9) and which ADC mode to use. The ADAX command also measures the 2nd reference. There are options in the ADAX command to measure subsets of the GPIOs and the 2nd reference separately or to measure all nine GPIOs and the 2nd reference in a single command. See the section on Commands for the ADAX command format. All auxiliary measurements are relative to the $V^{-}$ pin voltage. This command can be used to read external temperatures by connecting temperature sensors to the GPIOs. These sensors can be powered from the 2nd reference which is also measured by the ADAX command, resulting in precise ratiometric measurements.

Figure 5 illustrates the timing of the ADAX command measuring all GPIOs and the 2nd reference. All 10 measurements are carried out on ADC1 alone. The 2nd reference is measured after GPIO5 and before GPIO6.

Table 7 shows the conversion time for the ADAX command measuring all of the GPIOs and the 2nd reference. $t_{10C}$ indicates the total conversion time.

![Figure 5. Timing for ADAX Command Measuring All GPIOs and 2nd Reference](ltc6813-1/figures/ltc6813-1-f057.png)

*Figure 5. Timing for ADAX Command Measuring All GPIOs and 2nd Reference*

**Table 7. Conversion and Synchronization Times for ADAX Command Measuring All GPIOs and 2nd Reference in Different Modes** ([table-11-p25-data.csv](ltc6813-1/tables/table-11-p25-data.csv), p. 25)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{2M}$ | $t_{9M}$ | $t_{10M}$ | $t_{10C}$ | $t_{SKEW}$ |
|---|---|---|---|---|---|---|---|
| **CONVERSION TIMES (IN µs)** |  |  |  |  |  |  |  |
| 27kHz | 0 | 58 | 104 | 431 | 478 | 1,825 | 420 |
| 14kHz | 0 | 87 | 163 | 693 | 769 | 2,116 | 682 |
| 7kHz | 0 | 145 | 279 | 1,217 | 1,350 | 3,862 | 1,205 |
| 3kHz | 0 | 261 | 512 | 2,264 | 2,514 | 5,025 | 2,253 |
| 2kHz | 0 | 494 | 977 | 4,358 | 4,841 | 7,353 | 4,347 |
| 1kHz | 0 | 960 | 1,908 | 8,547 | 9,496 | 12,007 | 8,536 |
| 422Hz | 0 | 1,890 | 3,770 | 16,926 | 18,805 | 21,316 | 16,915 |
| 26Hz | 0 | 29,818 | 59,624 | 268,271 | 298,078 | 335,498 | 268,260 |

### Auxiliary (GPIO) Measurements with Digital Redundancy (ADAXD Command)
<!-- page: 25 -->

The ADAXD command operates similarly to the ADAX command except that an additional diagnostic is performed using digital redundancy. PS[1:0] in Configuration Register Group B must be set to 0 or 1 during ADAXD to enable redundancy. See the ADC Conversion with Digital Redundancy section.

The execution time of ADAX and ADAXD is the same.

### Measuring Cell Voltages and GPIOs (ADCVAX Command)
<!-- page: 25 -->

The ADCVAX command combines eighteen cell measurements with two GPIO measurements (GPIO1 and GPIO2). This command simplifies the synchronization of battery cell voltage and current measurements when current sensors are connected to GPIO1 or GPIO2 inputs. Figure 6 illustrates the timing of the ADCVAX command. See the section on Commands for the ADCVAX command format. The synchronization of the current and voltage measurements, $t_{SKEW1}$, in Fast mode is within 194μs.

Table 8 shows the conversion and synchronization time for the ADCVAX command in different modes. The total conversion time for the command is given by $t_{8C}$.

![Figure 6. Timing of ADCVAX Command](ltc6813-1/figures/ltc6813-1-f058.png)

*Figure 6. Timing of ADCVAX Command*

### Table 8. Conversion and Synchronization Times for ADCVAX Command in Different Modes
<!-- page: 26 -->

**Table 8. Conversion and Synchronization Times for ADCVAX Command in Different Modes** ([table-12-p26-data.csv](ltc6813-1/tables/table-12-p26-data.csv), p. 26)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{2M}$ | $t_{3M}$ | $t_{4M}$ | $t_{5M}$ | $t_{6M}$ | $t_{7M}$ | $t_{8M}$ | $t_{8C}$ | $t_{SKEW1}$ |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 27kHz | 0 | 58 | 104 | 151 | 205 | 252 | 306 | 352 | 399 | 1,511 | 194 |
| 14kHz | 0 | 87 | 163 | 238 | 321 | 397 | 480 | 556 | 632 | 1,744 | 310 |
| 7kHz | 0 | 145 | 279 | 413 | 554 | 688 | 829 | 963 | 1,097 | 3,140 | 543 |
| 3kHz | 0 | 261 | 512 | 762 | 1,020 | 1,270 | 1,527 | 1,778 | 2,028 | 4,071 | 1,008 |
| 2kHz | 0 | 494 | 977 | 1,460 | 1,950 | 2,433 | 2,924 | 3,407 | 3,890 | 5,933 | 1,939 |
| 1kHz | 0 | 960 | 1,908 | 2,857 | 3,812 | 4,761 | 5,717 | 6,665 | 7,613 | 9,657 | 3,801 |
| 422Hz | 0 | 1,890 | 3,770 | 5,649 | 7,536 | 9,415 | 11,302 | 13,181 | 15,061 | 17,104 | 7,525 |
| 26Hz | 0 | 29,818 | 59,624 | 89,431 | 119,245 | 149,052 | 178,866 | 208,672 | 238,479 | 268,450 | 119,234 |

### DATA ACQUISITION SYSTEM DIAGNOSTICS
<!-- page: 26 -->

The battery monitoring data acquisition system is comprised of the multiplexers, ADCs, 1st reference, digital filters and memory. To ensure long term reliable performance there are several diagnostic commands which can be used to verify the proper operation of these circuits. 

### Measuring Internal Device Parameters (ADSTAT Command)
<!-- page: 26 -->

The ADSTAT command is a diagnostic command that measures the following internal device parameters: Sum of All Cells (SC), Internal Die Temperature (ITMP), Analog Power Supply (VA) and the Digital Power Supply (VD). These parameters are described in the section below. All the 8 ADC modes described earlier are available for these conversions. See the section on Commands for the ADSTAT command format. Figure 7 illustrates the timing of the ADSTAT command measuring all 4 internal device parameters.

Table 9 shows the conversion time of the ADSTAT command measuring all 4 internal parameters. $t_{4C}$ indicates the total conversion time for the ADSTAT command. 

![Figure 7. Timing for ADSTAT Command Measuring SC, ITMP , VA, VD](ltc6813-1/figures/ltc6813-1-f059.png)

*Figure 7. Timing for ADSTAT Command Measuring SC, ITMP , VA, VD*

68131 F07

**Table 9. Conversion and Synchronization Times for ADSTAT Command Measuring SC, ITMP, VA, VD in Different Modes** ([table-13-p27-data.csv](ltc6813-1/tables/table-13-p27-data.csv), p. 27)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{2M}$ | $t_{3M}$ | $t_{4M}$ | $t_{4C}$ | $t_{SKEW}$ |
|---|---|---|---|---|---|---|---|
| **CONVERSION TIMES (IN µs)** |  |  |  |  |  |  |  |
| 27kHz | 0 | 58 | 104 | 151 | 198 | 742 | 140 |
| 14kHz | 0 | 87 | 163 | 238 | 314 | 858 | 227 |
| 7kHz | 0 | 145 | 279 | 413 | 547 | 1,556 | 402 |
| 3kHz | 0 | 261 | 512 | 762 | 1,012 | 2,022 | 751 |
| 2kHz | 0 | 494 | 977 | 1,460 | 1,943 | 2,953 | 1,449 |
| 1kHz | 0 | 960 | 1,908 | 2,857 | 3,805 | 4,814 | 2,845 |
| 422Hz | 0 | 1,890 | 3,770 | 5,649 | 7,529 | 8,538 | 5,638 |
| 26Hz | 0 | 29,818 | 59,624 | 89,431 | 119,238 | 134,211 | 89,420 |

Sum of All Cells Measurement: The Sum of All Cells measurement is the voltage between C18 and C0 with a 30:1 attenuation. The 16-bit ADC value of Sum of All Cells measurement (SC) is stored in Status Register Group A. Any potential difference between the C0 and V pins results in an error in the SC measurement equal to this difference. From the SC value, the sum of all cell voltage measurements is given by:

![Equation as printed (p. 27)](ltc6813-1/figures/ltc6813-1-eq10.png)

$$\text{Sum of All Cells} = SC \cdot 30 \cdot 100\,\mu\mathrm{V}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Internal Die Temperature: The ADSTAT command can measure the internal die temperature. The 16-bit ADC value of the die temperature measurement (ITMP) is stored in Status Register Group A. From ITMP , the actual die temperature is calculated using the expression:

Internal Die Temperature ( ° C) =

![Equation as printed (p. 27)](ltc6813-1/figures/ltc6813-1-eq02.png)

$$\text{Internal Die Temperature ( ° C) = } ITMP \cdot \left( \frac{100 \mu V}{7.6 mV} \right) \circ C - 276^{\circ} C$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Power Supply Measurements: The ADSTAT command is also used to measure the Analog Power Supply ($V_{REG}$) and Digital Power Supply ($V_{REGD}$). The 16-bit ADC value of the analog power supply measurement (VA) is stored in Status Register Group A. The 16-bit ADC value of the digital power supply measurement (VD) is stored in Status Register Group B. From VA and VD, the power supply measurements are given by:

![Equation as printed (p. 27)](ltc6813-1/figures/ltc6813-1-eq03.png)

$$
\begin{aligned}
\text{Analog Power Supply Measurement } (V_{\mathrm{REG}}) &= V_A \cdot 100\,\mu\mathrm{V} \\[6pt]
\text{Digital Power Supply Measurement } (V_{\mathrm{REGD}}) &= V_D \cdot 100\,\mu\mathrm{V}
\end{aligned}
$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The value of $V_{REG}$ is determined by external components. $V_{REG}$ should be between 4.5V and 5.5V to maintain accuracy. The value of $V_{REGD}$ is determined by internal components. The normal range of $V_{REGD}$ is 2.7V to 3.6V.

### Measuring Internal Device Parameters with Digital Redundancy (ADSTATD Command)
<!-- page: 27 -->

The ADSTATD command operates similarly to the ADSTAT command except that an additional diagnostic is performed using digital redundancy. PS[1:0] in Configuration Register Group B must be set to 0 or 1 during ADSTATD to enable redundancy. See the ADC Conversion with Digital Redundancy section.

The execution time of ADSTAT and ADSTATD is the same.

### ADC Conversion with Digital Redundancy
<!-- page: 27 -->

Each of the three internal ADCs contains its own digital integration and differentiation machine. The LTC6813-1 also contains a fourth digital integration and differentiation machine that is used for redundancy and error checking.

All of the ADC and self test commands, except ADAX and ADSTAT , can operate with digital redundancy. This includes  ADCV ,  ADOW,  CVST ,  ADOL,  ADAXD,  AXOW, AXST , ADSTATD, STATST , ADCVAX and ADCVSC. When performing an ADC conversion with redundancy, the analog modulator sends its bit stream to both the primary digital machine and the redundant digital machine. At the end of the conversion the results from the two machines are compared. If any result bit mismatch is detected then a digital redundancy fault code is stored in place of the

ADC result. The digital redundancy fault code is a value of 0xFF0X. This is detectable because it falls outside the normal result range of 0x0000 to 0xDFFF . The last four bits are used to indicate which nibble(s) of the result values did not match.

### Indication of Digital Redundancy Fault Codes
<!-- page: 28 -->

**Indication of Digital Redundancy Fault Codes** ([table-14-p28-data.csv](ltc6813-1/tables/table-14-p28-data.csv), p. 28)

| DIGITAL REDUNDANCY FAULT CODE 4 LSBs | INDICATION |
|---|---|
| 0b0XXX | No fault detected in bits 15–12 |
| 0b1XXX | Fault detected in bits 15–12 |
| 0bX0XX | No fault detected in bits 11–8 |
| 0bX1XX | Fault detected in bits 11–8 |
| 0bXX0X | No fault detected in bits 7–4 |
| 0bXX1X | Fault detected in bits 7–4 |
| 0bXXX0 | No fault detected in bits 3–0 |
| 0bXXX1 | Fault detected in bits 3–0 |
| 0b0000 | The digital redundancy feature will not write this value of all zeros in the last 4 bits |

Since there is a single redundant digital machine, it can apply redundancy to only one ADC at a time. By default, the LTC6813-1 will automatically select ADC path redundancy. However, the user can choose an ADC redundancy path selection by writing to the PS[1:0] bits in Configuration Register Group B.

**Table 10. ADC Path Redundancy Selection** ([table-15-p28-data.csv](ltc6813-1/tables/table-15-p28-data.csv), p. 28)

| MEASURE | PS[1:0] = 00 PATH SELECT | PS[1:0] = 00 REDUNDANT MEASURE | PS[1:0] = 01 PATH SELECT | PS[1:0] = 01 REDUNDANT MEASURE | PS[1:0] = 10 PATH SELECT | PS[1:0] = 10 REDUNDANT MEASURE | PS[1:0] = 11 PATH SELECT | PS[1:0] = 11 REDUNDANT MEASURE |
|---|---|---|---|---|---|---|---|---|
| Cells 1, 7, 13 | ADC1 | Cell 1 | ADC1 | Cell 1 | ADC2 | Cell 7 | ADC3 | Cell 13 |
| Cells 2, 8, 14 | ADC2 | Cell 8 | ADC1 | Cell 2 | ADC2 | Cell 8 | ADC3 | Cell 14 |
| Cells 3, 9, 15 | ADC3 | Cell 15 | ADC1 | Cell 3 | ADC2 | Cell 9 | ADC3 | Cell 15 |
| Cells 4, 10, 16 | ADC1 | Cell 4 | ADC1 | Cell 4 | ADC2 | Cell 10 | ADC3 | Cell 16 |
| Cells 5, 11, 17 | ADC2 | Cell 11 | ADC1 | Cell 5 | ADC2 | Cell 11 | ADC3 | Cell 17 |
| Cells 6, 12, 18 | ADC3 | Cell 18 | ADC1 | Cell 6 | ADC2 | Cell 12 | ADC3 | Cell 18 |
| Cell 7 (ADOL) | ADC2 | Cell 7 | ADC1 | Cell 7 | ADC2 | Cell 7 | ADC3 | N/A |
| Cell 13 (ADOL) | ADC2 | Cell 13 | ADC1 | N/A | ADC2 | Cell 13 | ADC3 | Cell 13 |
| GPIO[n]* | ADC1 | GPIO[n] | ADC1 | GPIO[n] | ADC2 | N/A | ADC3 | N/A |
| 2nd Reference* | ADC1 | 2nd Ref | ADC1 | 2nd Ref | ADC2 | N/A | ADC3 | N/A |
| SC* | ADC1 | SC | ADC1 | SC | ADC2 | N/A | ADC3 | N/A |
| ITMP* | ADC1 | ITMP | ADC1 | ITMP | ADC2 | N/A | ADC3 | N/A |
| VA* | ADC1 | VA | ADC1 | VA | ADC2 | N/A | ADC3 | N/A |
| VD* | ADC1 | VD | ADC1 | VD | ADC2 | N/A | ADC3 | N/A |

- **\*:** Note that the ADAX and ADSTAT commands are identical to the ADAXD and ADSTATD commands except that ADAX and ADSTAT will not apply any digital redundancy.

Table  10  shows  all  possible  ADC  path  redundancy selections.

When the FDRF bit in Configuration Register Group B is written to 1 it will force the digital redundancy comparison to fail during subsequent ADC conversions.

### Measuring Cell Voltages and Sum of All Cells (ADCVSC Command)
<!-- page: 28 -->

The ADCVSC command combines eighteen cell measurements and the measurement of Sum of All Cells. This command simplifies the synchronization of the individual battery cell voltage and the total Sum of All Cells measurements. Figure 8 illustrates the timing of the ADCVSC command. See the section on Commands for the ADCVSC command format. The synchronization of the cell voltage and Sum of All Cells measurements, $t_{SKEW}$, in Fast mode is within 147µs.

Table 11 shows the conversion and synchronization time for the ADCVSC command in different modes. The total conversion time for the command is given by $t_{7C}$.

![Figure 8. Timing for ADCVSC Command Measuring All 18 Cells, SC](ltc6813-1/figures/ltc6813-1-f060.png)

*Figure 8. Timing for ADCVSC Command Measuring All 18 Cells, SC*

**Table 11. Conversion and Synchronization Times for ADCVSC Command in Different Modes** ([table-16-p29-data.csv](ltc6813-1/tables/table-16-p29-data.csv), p. 29)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{2M}$ | $t_{3M}$ | $t_{4M}$ | $t_{5M}$ | $t_{6M}$ | $t_{7M}$ | $t_{7C}$ | $t_{SKEW}$ |
|---|---|---|---|---|---|---|---|---|---|---|
| 27kHz | 0 | 58 | 104 | 151 | 205 | 259 | 306 | 352 | 1,331 | 147 |
| 14kHz | 0 | 87 | 163 | 238 | 321 | 404 | 480 | 556 | 1,534 | 235 |
| 7kHz | 0 | 145 | 279 | 413 | 554 | 695 | 829 | 963 | 2,756 | 409 |
| 3kHz | 0 | 261 | 512 | 762 | 1,020 | 1,277 | 1,527 | 1,778 | 3,571 | 758 |
| 2kHz | 0 | 494 | 977 | 1,460 | 1,950 | 2,441 | 2,924 | 3,407 | 5,200 | 1,456 |
| 1kHz | 0 | 960 | 1,908 | 2,857 | 3,812 | 4,768 | 5,717 | 6,665 | 8,458 | 2,853 |
| 422Hz | 0 | 1,890 | 3,770 | 5,649 | 7,536 | 9,423 | 11,302 | 13,181 | 14,974 | 5,645 |
| 26Hz | 0 | 29,818 | 59,624 | 89,431 | 119,245 | 149,059 | 178,866 | 208,672 | 234,902 | 89,427 |

### Overlap Cell Measurement (ADOL Command)
<!-- page: 30 -->

The ADOL command first simultaneously measures Cell 7 with ADC1 and ADC2. Then it simultaneously measures Cell 13 with both ADC2 and ADC3. The host can compare the results against each other to look for inconsistencies which may indicate a fault. The result of the Cell 7 measurement from ADC2 is placed in Cell Voltage Register Group C where the Cell 7 result normally resides. The result from ADC1 is placed in Cell Voltage Register Group C where the Cell 8 result normally resides. The result of the Cell 13 measurement from ADC3 is placed in Cell Voltage Register Group E where the Cell 13 result normally resides. The result from ADC2 is placed in Cell Voltage Register Group E where the Cell 14 result normally resides. Figure 9 illustrates the timing of the ADOL command. See the section on Commands for the ADOL command format.

Table 12 shows the conversion time for the ADOL command. $t_{2C}$ indicates  the  total  conversion  time  for  this command.

### Accuracy Check
<!-- page: 30 -->

Measuring an independent voltage reference is the best means to verify the accuracy of a data acquisition system. The LTC6813-1 contains a 2nd reference for this purpose. The ADAX command will initiate the measurement of the 2nd reference. The results are placed in Auxiliary Register Group B. The range of the result depends on the ADC1 measurement accuracy and the accuracy of the 2nd reference, including thermal hysteresis and long term drift. Readings outside the range 2.990V to 3.014V (2.992V to 3.012V for LTC6813I) indicate the system is out of its specified tolerance. ADC2 is verified by comparing it to ADC1 using the ADOL command. ADC3 is verified by comparing it to ADC2 using the ADOL command.

![Figure 9. Timing for ADOL Command](ltc6813-1/figures/ltc6813-1-f062.png)

*Figure 9. Timing for ADOL Command*

**Table 12. Conversion Times for ADOL Command** ([table-17-p30-data.csv](ltc6813-1/tables/table-17-p30-data.csv), p. 30)

| MODE | $t_{0}$ | $t_{1M}$ | $t_{2M}$ | $t_{2C}$ |
|---|---|---|---|---|
| **CONVERSION TIMES (IN µs)** |  |  |  |  |
| 27kHz | 0 | 58 | 106 | 384 |
| 14kHz | 0 | 87 | 164 | 442 |
| 7kHz | 0 | 146 | 281 | 791 |
| 3kHz | 0 | 262 | 513 | 1,024 |
| 2kHz | 0 | 495 | 979 | 1,490 |
| 1kHz | 0 | 960 | 1,910 | 2,420 |
| 422Hz | 0 | 1,891 | 3,772 | 4,282 |
| 26Hz | 0 | 29,818 | 59,626 | 67,119 |

### MUX Decoder Check
<!-- page: 31 -->

The diagnostic command DIAGN ensures the proper operation of each multiplexer channel. The command cycles through all channels and sets the MUXFAIL bit to 1 in Status Register Group B if any channel decoder fails. The MUXFAIL bit is set to 0 if the channel decoder passes the test. The MUXFAIL is also set to 1 on power-up (POR) or after a CLRSTAT command.

The DIAGN command takes about 400µs to complete if the Core is in REFUP state and about 4.5ms to complete if  the  Core is in STANDBY state. The polling methods described in the section Polling Methods can be used to determine the completion of the DIAGN command.

### Digital Filter Check
<!-- page: 31 -->

The delta-sigma ADC is composed of a 1-bit pulse density modulator followed by a digital filter . A pulse density modulated bit stream has a higher percentage of 1s for higher analog input voltages. The digital filter converts this high frequency 1-bit stream into a single 16-bit word.

This is why a delta-sigma ADC is often referred to as an oversampling converter .

The self test commands verify the operation of the digital filters and memory. Figure 10 illustrates the operation of the ADC during self test. The output of the 1-bit pulse density modulator is replaced by a 1-bit test signal. The test signal passes through the digital filter and is converted to a 16-bit value. The 1-bit test signal undergoes the same digital conversion as the regular 1-bit signal from the modulator , so the conversion time for any self test command is exactly the same as the corresponding regular ADC conversion command. The 16-bit ADC value is stored in the same register groups as the corresponding regular ADC conversion command. The test signals are designed to place alternating one-zero patterns in the registers. Table 13 provides a list of the self test commands. If the digital filters and memory are working properly, then the registers will contain the values shown in Table 13. For more details see the Commands section.

![Figure 10. Operation of LTC6813-1 ADC Self Test](ltc6813-1/figures/ltc6813-1-f064.png)

*Figure 10. Operation of LTC6813-1 ADC Self Test*

**Table 13. Self Test Command Summary** ([table-18-p31-data.csv](ltc6813-1/tables/table-18-p31-data.csv), p. 31)

| COMMAND | SELF TEST OPTION | 27kHz | 14kHz | 7kHz, 3kHz, 2kHz, 1kHz, 422Hz, 26Hz | RESULTS REGISTER GROUPS |
|---|---|---|---|---|---|
| **OUTPUT PATTERN IN DIFFERENT ADC MODES** |  |  |  |  |  |
| CVST | ST[1:0] = 01 | 0x9565 | 0x9553 | 0x9555 | C1V to C18V (CVA, CVB, CVC, CVD, CVE, CVF) |
| CVST | ST[1:0] = 10 | 0x6A9A | 0x6AAC | 0x6AAA | C1V to C18V (CVA, CVB, CVC, CVD, CVE, CVF) |
| AXST | ST[1:0] = 01 | 0x9565 | 0x9553 | 0x9555 | G1V to G9V, REF (AUXA, AUXB, AUXC, AUXD) |
| AXST | ST[1:0] = 10 | 0x6A9A | 0x6AAC | 0x6AAA | G1V to G9V, REF (AUXA, AUXB, AUXC, AUXD) |
| STATST | ST[1:0] = 01 | 0x9565 | 0x9553 | 0x9555 | SC, ITMP, VA, VD (STATA, STATB) |
| STATST | ST[1:0] = 10 | 0x6A9A | 0x6AAC | 0x6AAA | SC, ITMP, VA, VD (STATA, STATB) |

### ADC Clear Commands
<!-- page: 32 -->

LTC6813-1  has  3  clear  ADC  commands:  CLRCELL, CLRAUX and CLRSTAT . These commands clear the registers that store all ADC conversion results.

The  CLRCELL  command  clears  Cell  Voltage  Register Groups A, B, C, D, E and F . All bytes in these registers are set to 0xFF by CLRCELL command.

The  CLRAUX  command  clears  Auxiliary  Register Groups A, B, C and D. All bytes in these registers, except the last four registers of Group D, are set to 0xFF by CLRAUX command.

The CLRSTAT command clears Status Register Groups A and B except the REV and RSVD bits in Status Register Group B. A read back of REV will return the revision code of the part. RSVD bits always read back 0s. All OV and UV flags, MUXFAIL bit, and THSD bit in Status Register Group B and also in Auxiliary Register Group D are set to 1 by CLRSTAT command. The THSD bit is set to 0 after RDSTATB command. The registers storing SC, ITMP , VA and VD are all set to 0xFF by CLRSTAT command.

### Open Wire Check (ADOW Command)
<!-- page: 32 -->

The ADOW command is used to check for any open wires between the ADCs of the LTC6813-1 and the external cells. This command performs ADC conversions on the C pin inputs identically to the ADCV command, except two internal current sources sink or source current into the two C pins while they are being measured. The pullup (PUP) bit of the ADOW command determines whether the current sources are sinking or sourcing 100µA.

The following simple algorithm can be used to check for an open wire on any of the 19 C pins:

1. Run the 18-cell command ADOW with PUP = 1 at least twice. Read the cell voltages for cells 1 through 18 once at the end and store them in array $CELL_{PU}$ (n ).
2. Run the 18-cell command ADOW with PUP = 0 at least twice. Read the cell voltages for cells 1 through 18 once at the end and store them in array $CELL_{PD}$ (n ).
3. Take the difference between the pull-up and pull-down measurements made in above steps for cells 2 to 18: $CELL_{\Delta}$(n) = $CELL_{PU}$ (n) - $CELL_{PD}$ (n ).
4. For  all  values  of  n  from  1  to  17:    If  $CELL_{\Delta}$(n+1) < -400mV, then C(n) is open. If $CELL_{PU}$ (1) = 0.0000, then C(0) is open. If $CELL_{PD}$ (18) = 0.0000, then C(18) is open.

The above algorithm detects open wires using normal mode conversions with as much as 10nF of capacitance remaining  on  the  LTC6813-1  side  of  the  open  wire. However, if more external capacitance is on the open C pin, then the length of time that the open wire conversions are ran in steps 1 and 2 must be increased to give the 100µA current sources time to create a large enough difference for the algorithm to detect an open connection. This can be accomplished by running more than two ADOW commands in steps 1 and 2, or by using filtered mode conversions instead of normal mode conversions. Use Table 14 to determine how many conversions are necessary:

**Table 14. (External C Pin Capacitance / Number of ADOW Commands Required in Steps 1 and 2)** ([table-19-p32-data.csv](ltc6813-1/tables/table-19-p32-data.csv), p. 32)

| EXTERNAL C PIN CAPACITANCE | NORMAL MODE | FILTERED MODE |
|---|---|---|
| **NUMBER OF ADOW COMMANDS REQUIRED IN STEPS 1 AND 2** |  |  |
| ≤10nF | 2 | 2 |
| 100nF | 10 | 2 |
| 1µF | 100 | 2 |
| C | 1 + ROUNDUP (C/10nF) | 2 |

### Auxiliary Open Wire Check (AXOW Command)
<!-- page: 32 -->

The AXOW command is used to check for any open wires between the GPIO pins of the LTC6813-1 and the external circuit. This command performs ADC conversions on the GPIO pin inputs identically to the ADAX command, except internal current sources sink or source current into each GPIO pin while it is being measured. The pull-up (PUP) bit of the AXOW command determines whether the current sources are sinking or sourcing 100µA.

### Thermal Shutdown
<!-- page: 32 -->

To protect the LTC6813-1 from overheating, there is a thermal shutdown circuit included inside the IC. If the temperature detected on the die goes above approximately 150°C, the thermal shutdown circuit trips and resets  the  Configuration  Register  Groups  (except  the MUTE bit) and turns off all discharge switches. When a thermal shutdown event has occurred, the THSD bit in Status Register Group B will go high. The CLRSTAT command can also set the THSD bit high for diagnostic purposes. This bit is cleared when a read operation is performed on Status Register Group B (RDSTATB command). The CLRSTAT command sets the THSD bit high for diagnostic purposes but does not reset the Configuration Register Groups.

### Revision Code
<!-- page: 32 -->

The Status Register Group B contains a 4-bit revision code (REV). If software detection of device revision is necessary, then contact the factory for details. Otherwise, the code can be ignored. In all cases, however , the values of all bits must be used when calculating the Packet Error Code (PEC) on data reads.

### WATCHDOG AND DISCHARGE TIMER
<!-- page: 33 -->

When there is no valid command for more than 2 seconds, the watchdog timer expires. This resets Configuration Register bytes CFGAR0, CFGAR1-3 (if DTMEN = 0) and the GPIO bits in Configuration Register Group B in all cases. CFGAR4, CFGAR5, the S Control Register Group (including S control bits in PWM/S Control Register Group B) and the remainder of Configuration Register Group B are reset by the watchdog timer when the discharge timer is disabled. The WDT pin is pulled high by the external pullup when the watchdog time elapses. The watchdog timer is always enabled and it resets after every valid command with matching command PEC.

The  discharge  timer  is  used  to  keep  the  discharge switches turned ON for programmable time duration. If the discharge timer is being used, the discharge switches are not turned OFF when the watchdog timer is activated.

To enable the discharge timer , connect the DTEN pin to $V_{REG}$ (Figure 11). In this configuration, the discharge switches  will  remain  ON  for  the  programmed  time duration that is determined by the DCTO value written in Configuration Register Group A. Table 15 shows the various time settings and the corresponding DCTO value.

![Figure 11. Watchdog and Discharge Timer](ltc6813-1/figures/ltc6813-1-f065.png)

*Figure 11. Watchdog and Discharge Timer*

### Table 15. DCTO Settings
<!-- page: 34 -->

**Table 15. DCTO Settings** ([table-20-p34-data.csv](ltc6813-1/tables/table-20-p34-data.csv), p. 34)

| DCTO | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | A | B | C | D | E | F |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TIME (MIN) | Disabled | 0.5 | 1 | 2 | 3 | 4 | 5 | 10 | 15 | 20 | 30 | 40 | 60 | 75 | 90 | 120 |

**Table 16. (Watchdog Timer / Discharge Timer Reset Behavior)** ([table-21-p34-data.csv](ltc6813-1/tables/table-21-p34-data.csv), p. 34)

|  | WATCHDOG TIMER | DISCHARGE TIMER |
|---|---|---|
| DTEN = 0, DCTO = XXXX | Resets CFGAR0-5, CFGBR0-1 and SCTRL When It Fires | Disabled |
| DTEN = 1, DCTO = 0000 | Resets CFGAR0-5, CFGBR0-1 and SCTRL When It Fires | Disabled |
| DTEN = 1, DCTO != 0000 | Resets CFGAR0, CFGAR1-3 (if DTMEN = 0) and GPIO Bits in CFGBR0 When It Fires | Resets CFGAR1-3 (if DTMEN = 1), CFGAR4-5, SCTRL and Remainder of CFGBR0-1 (except MUTE Bit) When It Fires |

Table  16  summarizes  the  status  of  the  Configuration Register Groups after a watchdog timer or discharge timer event.

The status of the discharge timer can be determined by reading Configuration Register Group A using the RDCFGA command. The DCTO value indicates the time left before the discharge timer expires as shown in Table 17.

**Table 17. (DCTO Read Value / Discharge Time Left)** ([table-22-p34-data.csv](ltc6813-1/tables/table-22-p34-data.csv), p. 34)

| DCTO (READ VALUE) | DISCHARGE TIME LEFT (MIN) |
|---|---|
| 0 | Disabled (or) Timer Has Timed Out |
| 1 | 0 < Timer ≤ 0.5 |
| 2 | 0.5 < Timer ≤ 1 |
| 3 | 1 < Timer ≤ 2 |
| 4 | 2 < Timer ≤ 3 |
| 5 | 3 < Timer ≤ 4 |
| 6 | 4 < Timer ≤ 5 |
| 7 | 5 < Timer ≤ 10 |
| 8 | 10 < Timer ≤ 15 |
| 9 | 15 < Timer ≤ 20 |
| A | 20 < Timer ≤ 30 |
| B | 30 < Timer ≤ 40 |
| C | 40 < Timer ≤ 60 |
| D | 60 < Timer ≤ 75 |
| E | 75 < Timer ≤ 90 |
| F | 90 < Timer ≤ 120 |

Unlike the watchdog timer , the discharge timer does not reset  when  there  is  a  valid  command.  The  discharge timer  can  only  be  reset  after  a  valid  WRCFGA  (Write Configuration Register Group A) command. There is a possibility that the discharge timer will expire in the middle of some commands.

If the discharge timer activates in the middle of a WRCFGA command, the Configuration Register Groups and S Control Register Group (including S control bits in PWM/S Control Register Group B) will reset as per Table 16. However, at the end of the valid WRCFGA command, the new data is copied to Configuration Register Group A. The new configuration data is not lost when the discharge timer is activated. 

If the discharge timer activates in the middle of a RDCFGA or RDCFGB command, the Configuration Register Groups reset as per Table 16. As a result, the read back data from bytes CFGAR4 and CFGAR5 and CFGBR0 and CFGBR1 could be corrupted. If the discharge timer activates in the middle of a RDSCTRL or RDPSB command, the S Control Register Group (including S control bits in PWM/S Control Register Group B) resets as per Table 16. As a result, the read back data could be corrupted.


### RESET BEHAVIORS
<!-- page: 35 -->

Power cycling, thermal shutdown, watchdog timeout and discharge timeout can cause various registers and circuitry to reset when they occur . The following summarizes the behaviors when these events occur:

**Reset Event / Device Behavior** ([table-23-p35-data.csv](ltc6813-1/tables/table-23-p35-data.csv), p. 35)

| RESET EVENT | DEVICE BEHAVIOR |
|---|---|
| Power Cycle ($V^{+}$ and $V_{REG}$ both power cycled) | Transition to STANDBY state. All registers and state machines are reset to default values. Cell discharge is disabled. |
| Thermal Shutdown | Cell discharge is disabled, but S Control Register Group is not reset. All of Configuration Register Group A is reset. All of Configuration Register Group B is reset except the MUTE bit. The COMM Register Group is reset. |
| Watchdog Timeout (while Discharge Timer is Running) | Transition to EXTENDED BALANCING state. CFGAR0 of Configuration Register Group A is reset. If DTMEN (in Configuration Register Group B) = 0 then CFGAR1, CFGAR2 and CFGAR3 of Configuration Register Group A are reset. Bits [3:0] of CFGBR0 (the GPIO bits) of Configuration Register Group B are reset. The COMM Register Group is reset. |
| Watchdog Timeout (no Discharge Timer Running) | Transition to SLEEP state. Cell discharge is disabled. All state machines are reset. All of Configuration Register Group A is reset. All of Configuration Register Group B is reset. The PWM Register Group is reset. The S Control Register Group is reset. The PWM/S Control Register Group is reset. The COMM Register Group is reset. |
| Discharge Timeout (while Watchdog Timeout has Elapsed) | Transition to SLEEP state. Same behavior as the previous case above. |
| Discharge Timeout (while Watchdog Timeout is not Elapsed) | Cell discharge is disabled. The PWM Register Group is reset. The S Control Register Group is reset. The PWM/S Control Register Group is reset. If DTMEN (in Configuration Register Group B) = 1 then CFGAR1, CFGAR2 and CFGAR3 of Configuration Register Group A are reset. CFGAR4 and CFGAR5 of Configuration Register Group A are reset. Bits [7:4] of CFGBR0 of Configuration Register Group B are reset. All of CFGBR1 of Configuration Register Group B is reset except the MUTE bit. |

### S PIN PULSE-WIDTH MODULATION FOR CELL BALANCING
<!-- page: 36 -->

For additional control of cell discharging, the host may configure the S pins to operate using pulse-width modulation. While the watchdog timer is not expired, the DCC bits in the Configuration Register Groups control the S pins directly. After the watchdog timer expires, PWM operation begins and continues for the remainder of the selected discharge time or until a wake-up event occurs (and the watchdog timer is reset). During PWM operation, the DCC bits must be set to 1 for the PWM feature to operate.

Once PWM operation begins, the configurations in the PWM register may cause some or all S pins to be periodically de-asserted to achieve the desired duty cycle as shown in Table 18. Each PWM signal operates on a 30 second period. For each cycle, the duty cycle can be programmed from 0% to 100% in increments of 1/15 = 6.67% (2 seconds).

Each S pin PWM signal is sequenced at different intervals to ensure that no two pins switch on or off at the same time. The switching interval between channels is 62.5ms, and 1.125s is required for all eighteen pins to switch (18 · 62.5ms).

The default values of the PWM control settings (located in  PWM Register Group and PWM/S Control Register Group B) are all 1s. Upon entering sleep mode, the PWM control settings will be initialized to their default values.

### DISCHARGE TIMER MONITOR
<!-- page: 36 -->

The LTC6813-1 has the ability to periodically monitor cell voltages while the discharge timer is active. The host should write the DTMEN bit in Configuration Register Group B to 1 to enable this feature.

When the discharge timer monitor is enabled and the watchdog timer has expired, the LTC6813-1 will perform a conversion of all cell voltages in 7kHz (Normal) mode every 30 seconds. The overvoltage and undervoltage comparisons will be performed and flags will be set if cells have crossed a threshold. For any undervoltage cells the discharge timer monitor will automatically clear the associated DCC bit in Configuration Register Group A or Configuration Register Group B so that the cell will no longer be discharged. Clearing the DCC bit will also disable PWM discharge. With this feature, the host can write the undervoltage threshold to the desired discharge level and use the discharge timer monitor to discharge all, or selected, cells (using either constant discharge or PWM discharge) down to that level.

During discharge timer monitoring, digital redundancy checking will be performed on the cell voltage measurements. If a digital redundancy failure occurs, all DCC bits will be cleared.

### Table 18. S Pin Pulse-Width Modulation Settings
<!-- page: 37 -->

**Table 18. S Pin Pulse-Width Modulation Settings** ([table-24-p37-data.csv](ltc6813-1/tables/table-24-p37-data.csv), p. 37)

| DCC BIT (CONFIG REGISTER GROUPS) | PWMC SETTING | ON TIME (SECONDS) | OFF TIME (SECONDS) | DUTY CYCLE (%) |
|---|---|---|---|---|
| 0 | 4'bXXXX | 0 | Continuously Off | 0 |
| 1 | 4'b1111 | Continuously On | 0 | 100.0 |
| 1 | 4'b1110 | 28 | 2 | 93.3 |
| 1 | 4'b1101 | 26 | 4 | 86.7 |
| 1 | 4'b1100 | 24 | 6 | 80.0 |
| 1 | 4'b1011 | 22 | 8 | 73.3 |
| 1 | 4'b1010 | 20 | 10 | 66.7 |
| 1 | 4'b1001 | 18 | 12 | 60.0 |
| 1 | 4'b1000 | 16 | 14 | 53.3 |
| 1 | 4'b0111 | 14 | 16 | 46.7 |
| 1 | 4'b0110 | 12 | 18 | 40.0 |
| 1 | 4'b0101 | 10 | 20 | 33.3 |
| 1 | 4'b0100 | 8 | 22 | 26.7 |
| 1 | 4'b0011 | 6 | 24 | 20.0 |
| 1 | 4'b0010 | 4 | 26 | 13.3 |
| 1 | 4'b0001 | 2 | 28 | 6.7 |
| 1 | 4'b0000 | 0 | Continuously Off | 0 |

### $I^{2}C$/SPI MASTER ON LTC6813-1 USING GPIOs
<!-- page: 39 -->

The I/O ports GPIO3, GPIO4 and GPIO5 on LTC6813-1 can be used as an $I^{2}C$ or SPI master port to communicate to an $I^{2}C$ or SPI slave. In the case of an $I^{2}C$ master , GPIO4 and GPIO5 form the SDA and SCL ports of the $I^{2}C$ interface, respectively. In the case of a SPI master , GPIO3, GPIO4 and GPIO5 become the CSBM, SDIOM and SCKM ports of the SPI interface respectively. The SPI master on LTC6813-1 supports SPI mode 3 (CHPA = 1, CPOL = 1).

The GPIOs are open-drain outputs, so an external pullup is required on these ports to operate as an $I^{2}C$ or SPI master. It is also important to write the GPIO bits to 1 in the Configuration Register Groups so these ports are not pulled low internally by the device.

### COMM Register
<!-- page: 39 -->

LTC6813-1 has a 6-byte COMM register as shown in Table 19. This register stores all data and control bits required for $I^{2}C$ or SPI communication to a slave. The COMM register  contains  three  bytes  of  data  Dn[7:0] to be transmitted to or received from the slave device. ICOMn[3:0] specify control actions before transmitting/ receiving each data byte. FCOMn[3:0] specify control actions after transmitting/receiving each data byte.

If the bit ICOMn[3] in the COMM register is set to 1, the part becomes a SPI master and if the bit is set to 0, the part becomes an $I^{2}C$ master .

**Table 19. COMM Register Memory Map** ([table-25-p38-register.csv](ltc6813-1/tables/table-25-p38-register.csv), p. 38)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| COMM0 | RD/WR | ICOM0[3] | ICOM0[2] | ICOM0[1] | ICOM0[0] | D0[7] | D0[6] | D0[5] | D0[4] |
| COMM1 | RD/WR | D0[3] | D0[2] | D0[1] | D0[0] | FCOM0[3] | FCOM0[2] | FCOM0[1] | FCOM0[0] |
| COMM2 | RD/WR | ICOM1[3] | ICOM1[2] | ICOM1[1] | ICOM1[0] | D1[7] | D1[6] | D1[5] | D1[4] |
| COMM3 | RD/WR | D1[3] | D1[2] | D1[1] | D1[0] | FCOM1[3] | FCOM1[2] | FCOM1[1] | FCOM1[0] |
| COMM4 | RD/WR | ICOM2[3] | ICOM2[2] | ICOM2[1] | ICOM2[0] | D2[7] | D2[6] | D2[5] | D2[4] |
| COMM5 | RD/WR | D2[3] | D2[2] | D2[1] | D2[0] | FCOM2[3] | FCOM2[2] | FCOM2[1] | FCOM2[0] |

**Table 20. Write Codes for ICOMn[3:0] and FCOMn[3:0] on $I^{2}C$ Master** ([table-26-p38-register.csv](ltc6813-1/tables/table-26-p38-register.csv), p. 38)

| CONTROL BITS | CODE | ACTION | DESCRIPTION |
|---|---|---|---|
| ICOMn[3:0] | 0110 | START | Generate a START Signal on $I^{2}C$ Port Followed by Data Transmission |
|  | 0001 | STOP | Generate a STOP Signal on $I^{2}C$ Port |
|  | 0000 | BLANK | Proceed Directly to Data Transmission on $I^{2}C$ Port |
|  | 0111 | No Transmit | Release SDA and SCL and Ignore the Rest of the Data |
| FCOMn[3:0] | 0000 | Master ACK | Master Generates an ACK Signal on Ninth Clock Cycle |
|  | 1000 | Master NACK | Master Generates a NACK Signal on Ninth Clock Cycle |
|  | 1001 | Master NACK + STOP | Master Generates a NACK Signal Followed by STOP Signal |

**Table 21. Write Codes for ICOMn[3:0] and FCOMn[3:0] on SPI Master** ([table-27-p38-register.csv](ltc6813-1/tables/table-27-p38-register.csv), p. 38)

| CONTROL BITS | CODE | ACTION | DESCRIPTION |
|---|---|---|---|
| ICOMn[3:0] | 1000 | CSBM Low | Generates a CSBM Low Signal on SPI Port (GPIO3) |
|  | 1010 | CSBM Falling Edge | Drives CSBM (GPIO3) High, then Low |
|  | 1001 | CSBM High | Generates a CSBM High Signal on SPI Port (GPIO3) |
|  | 1111 | No Transmit | Releases the SPI Port and Ignores the Rest of the Data |
| FCOMn[3:0] | X000 | CSBM Low | Holds CSBM Low at the End of Byte Transmission |
|  | 1001 | CSBM High | Transitions CSBM High at the End of Byte Transmission |

Table 20 describes the valid write codes for ICOMn[3:0] and FCOMn[3:0] and their behavior when using the part as an $I^{2}C$ master .

Table 21 describes the valid write codes for ICOMn[3:0] and FCOMn[3:0] and their behavior when using the part as a SPI master .

Note that only the codes listed in Table 20 and Table 21 are valid for ICOMn[3:0] and FCOMn[3:0]. Writing any other code that is not listed in Table 20 and Table 21 to ICOMn[3:0] and FCOMn[3:0] may result in unexpected behavior on the $I^{2}C$ or SPI port.

### COMM Commands
<!-- page: 39 -->

Three commands help accomplish $I^{2}C$ or SPI communication to the slave device: WRCOMM, STCOMM and RDCOMM.

WRCOMM Command: This command is used to write data to the COMM register . This command writes 6 bytes of data to the COMM register . The PEC needs to be written at the end of the data. If the PEC does not match, all data in the COMM register is cleared to 1s when CSB goes high. See the section Bus Protocols for more details on a write command format.

STCOMM Command: This  command initiates $I^{2}C$/SPI communication on the GPIO ports. The COMM register contains 3 bytes of data to be transmitted to the slave. During this command, the data bytes stored in the COMM register are transmitted to the slave $I^{2}C$ or SPI device and the data received from the $I^{2}C$ or SPI device is stored in the COMM register. This command uses GPIO4 (SDA) and  GPIO5  (SCL)  for  $I^{2}C$  communication  or  GPIO3 (CSBM), GPIO4 (SDIOM) and GPIO5 (SCKM) for SPI communication.

The STCOMM command is to be followed by 24 clock cycles for each byte of data to be transmitted to the slave device while holding CSB low. For example, to transmit three bytes of data to the slave, send STCOMM command and its PEC followed by 72 clock cycles. Pull CSB high at the end of the 72 clock cycles of STCOMM command. During $I^{2}C$ or SPI communication, the data received from the slave device is updated in the COMM register .

RDCOMM Command: The data received from the slave device can be read back from the COMM register using the RDCOMM command. The command reads back six bytes of data followed by the PEC. See the section Bus Protocols for more details on a read command format.

Table  22  describes  the  possible  read  back  codes  for ICOMn[3:0] and FCOMn[3:0] when using the part as an $I^{2}C$ master . Dn[7:0] contains the data byte transmitted by the $I^{2}C$ slave.

**Table 22. Read Codes for ICOMn[3:0] and FCOMn[3:0] on $I^{2}C$ Master** ([table-28-p39-register.csv](ltc6813-1/tables/table-28-p39-register.csv), p. 39)

| CONTROL BITS | CODE | DESCRIPTION |
|---|---|---|
| ICOMn[3:0] | 0110 | Master Generated a START Signal |
|  | 0001 | Master Generated a STOP Signal |
|  | 0000 | Blank, SDA Was Held Low Between Bytes |
|  | 0111 | Blank, SDA Was Held High Between Bytes |
| FCOMn[3:0] | 0000 | Master Generated an ACK Signal |
|  | 0111 | Slave Generated an ACK Signal |
|  | 1111 | Slave Generated a NACK Signal |
|  | 0001 | Slave Generated an ACK Signal, Master Generated a STOP Signal |
|  | 1001 | Slave Generated a NACK Signal, Master Generated a STOP Signal |

In  case  of  the  SPI  master ,  the  read  back  codes  for ICOMn[3:0] and FCOMn[3:0] are always 0111 and 1111, respectively. Dn[7:0] contains the data byte transmitted by the SPI slave.

Figure 12 illustrates the operation of LTC6813-1 as an $I^{2}C$ or SPI master using the GPIOs.

Any number of bytes can be transmitted to the slave in groups of 3 bytes using these commands. The GPIO ports will not get reset between different STCOMM commands. However, if the wait time between the commands is greater than 2s, the watchdog will time out and reset the ports to their default values.

![Figure 12. LTC6813-1 I 2 C/SPI Master Using GPIOs](ltc6813-1/figures/ltc6813-1-f066.png)

*Figure 12. LTC6813-1 $I^{2}C$/SPI Master Using GPIOs*

To transmit several bytes of data using an $I^{2}C$ master, a START signal is only required at the beginning of the entire data stream. A STOP signal is only required at the end of the data stream. All intermediate data groups can use a BLANK code before the data byte and an ACK/NACK signal as appropriate after the data byte. SDA and SCL will not get reset between different STCOMM commands.

To transmit several bytes of data using SPI master , a CSBM low signal is sent at the beginning of the 1st data byte. CSBM can be held low or taken high for intermediate data groups using the appropriate code on FCOMn[3:0]. A CSBM high signal is sent at the end of the last byte of data. CSBM, SDIOM and SCKM will not get reset between different STCOMM commands.

Figure 13 shows the 24 clock cycles following STCOMM command for an $I^{2}C$ master in different cases. Note that if ICOMn[3:0] specified a STOP condition, after the STOP signal is sent, the SDA and SCL lines are held high and all data in the rest of the word is ignored. If ICOMn[3:0] is a NO TRANSMIT , both SDA and SCL lines are released, and the rest of the data in the word is ignored. This is used when a particular device in the stack does not have to communicate to a slave.

Figure 14 shows the 24 clock cycles following STCOMM command for a SPI master. Similar to the $I^{2}C$ master , if ICOMn[3:0] specified a CSBM HIGH or a NO TRANSMIT condition, the CSBM, SCKM and SDIOM lines of the SPI master are released and the rest of the data in the word is ignored.

![Figure 13. STCOMM Timing Diagram for an I2C Master](ltc6813-1/figures/ltc6813-1-f138.png)

*Figure 13. STCOMM Timing Diagram for an $I^{2}C$ Master*

![Figure 14. STCOMM Timing Diagram for a SPI Master](ltc6813-1/figures/ltc6813-1-f139.png)

*Figure 14. STCOMM Timing Diagram for a SPI Master*

### Timing Specifications of $I^{2}C$ and SPI Master
<!-- page: 41 -->

The timing of the LTC6813-1 $I^{2}C$ or SPI master will be controlled by the timing of the communication at the LTC6813-1's primary SPI interface. Table 23 shows the $I^{2}C$ master timing relationship to the primary SPI clock. Table 24 shows the SPI master timing specifications.

**Table 23. $I^{2}C$ Master Timing** ([table-29-p41-spec.csv](ltc6813-1/tables/table-29-p41-spec.csv), p. 41)

| $I^{2}C$ MASTER PARAMETER | TIMING RELATIONSHIP TO PRIMARY SPI INTERFACE | TIMING SPECIFICATIONS AT $t_{CLK}$ = 1µs |
|---|---|---|
| SCL Clock Frequency | 1/(2 • $t_{CLK}$) | Max 500kHz |
| $t_{HD}$;STA | $t_{3}$ | Min 200ns |
| $t_{LOW}$ | $t_{CLK}$ | Min 1µs |
| $t_{HIGH}$ | $t_{CLK}$ | Min 1µs |
| $t_{SU}$;STA | $t_{CLK}$ + $t_{4}$* | Min 1.03µs |
| $t_{HD}$;DAT | $t_{4}$* | Min 30ns |
| $t_{SU}$;DAT | $t_{3}$ | Min 200ns |
| $t_{SU}$;STO | $t_{CLK}$ + $t_{4}$* | Min 1.03µs |
| $t_{BUF}$ | 3 • $t_{CLK}$ | Min 3µs |

- **\*:** Note: When using isoSPI, $t_{4}$ is generated internally and is a minimum of 30ns. Also, $t_{3}$ = $t_{CLK}$ – $t_{4}$. When using SPI, $t_{3}$ and $t_{4}$ are the low and high times of the SCK input, each with a specified minimum of 200ns.

**Table 24. SPI Master Timing** ([table-30-p41-spec.csv](ltc6813-1/tables/table-30-p41-spec.csv), p. 41)

| SPI MASTER PARAMETER | TIMING RELATIONSHIP TO PRIMARY SPI INTERFACE | TIMING SPECIFICATIONS AT $t_{CLK}$ = 1µs |
|---|---|---|
| SDIOM Valid to SCKM Rising Setup | $t_{3}$ | Min 200ns |
| SDIO Valid from SCKM Rising Hold | $t_{CLK}$ + $t_{4}$* | Min 1.03µs |
| SCKM Low | $t_{CLK}$ | Min 1µs |
| SCKM High | $t_{CLK}$ | Min 1µs |
| SCKM Period (SCKM_Low + SCKM_High) | 2 • $t_{CLK}$ | Min 2µs |
| CSBM Pulse Width | 3 • $t_{CLK}$ | Min 3µs |
| SCKM Rising to CSBM Rising | 5 • $t_{CLK}$ + $t_{4}$* | Min 5.03µs |
| CSBM Falling to SCKM Falling | $t_{3}$ | Min 200ns |
| CSBM Falling to SCKM Rising | $t_{CLK}$ + $t_{3}$ | Min 1.2µs |
| SCKM Falling to SDIOM Valid | Master Requires < $t_{CLK}$ |  |

- **\*:** Note: When using isoSPI, $t_{4}$ is generated internally and is a minimum of 30ns. Also, $t_{3}$ = $t_{CLK}$ – $t_{4}$. When using SPI, $t_{3}$ and $t_{4}$ are the low and high times of the SCK input, each with a specified minimum of 200ns.

### S PIN PULSING USING THE S PIN CONTROL SETTINGS
<!-- page: 42 -->

The S pins of the LTC6813-1 can be used as a simple serial interface. This is particularly useful for controlling Analog Devices LT8584, a monolithic flyback DC/ DC converter , designed to actively balance large battery stacks. The LT8584 has several operating modes which are controlled through a serial interface. The LTC6813-1 can communicate to an LT8584 by sending a sequence of pulses on each S pin to select a specific LT8584 mode. The S pin control settings (located in S Control Register Group and PWM/S Control Register Group B) are used to specify the behavior for each of the 18 S pins, where each nibble specifies whether the S pin should drive high, drive low, or send a pulse sequence of between 1 and 7 pulses. Table 25 shows the possible S pin behaviors that can be sent to the LT8584.

The S pin pulses occur at a pulse rate of 6.44kHz (155µs period). The pulse width will be 77.6µs. The S pin pulsing begins when the STSCTRL command is sent, after the last command PEC clock, provided that the command PEC matches. The host may then continue to clock SCK in order to poll the status of the pulsing. This polling works similarly to the ADC polling feature. The data out will remain logic low until the S pin pulsing sequence has completed.

![Table 25. S Pin Pulsing Behavior](ltc6813-1/figures/ltc6813-1-f069.png)

*Table 25. S Pin Pulsing Behavior*

While the S pin pulsing is in progress, new STSCTRL, WRSCTRL or WRPSB commands are ignored. The PLADC command may be used to determine when the S pin pulsing has completed.

If the WRSCTRL (or WRPSB) command and command PEC are received correctly but the data PEC does not match, then the S pin control settings will be cleared.

If  a  DCC  bit  in  Configuration  Register  Group  A  or Configuration Register Group B is asserted, the LTC6813-1 will drive the selected S pin low, regardless of the S pin control settings. The host should leave the DCC bits set to 0 when using the S pin control settings.

The CLRSCTRL command can be used to quickly reset the S pin control settings to all 0s and force the pulsing machine to release control of the S pins. This command may be helpful in reducing the diagnostic control loop time in an automotive application.

### S PIN MUTING
<!-- page: 43 -->

The S pins may be disabled by sending the MUTE command and re-enabled by sending the UNMUTE command. The MUTE and UNMUTE commands do not require any subsequent data and thus the commands will propagate quickly through a stack of LTC6813-1 devices. This allows the host to quickly (<100µs) disable and re-enable discharging without disturbing register contents. This can be useful, for instance, to allow for a specific settling time before taking cell measurements. The mute status is reported in the read-only MUTE bit in Configuration Register Group B.

### SERIAL INTERFACE OVERVIEW
<!-- page: 43 -->

There are two types of serial ports on the LTC6813-1: a standard 4-wire serial peripheral interface (SPI) and a 2-wire isolated interface (isoSPI). The state of the ISOMD pin determines whether pins 53, 54, 61 and 62 are a 2-wire or 4-wire serial port.

The LTC6813-1 is used in a daisy-chain configuration. A second isoSPI interface uses pins 57, 58, 63 and 64.

### 4-WIRE SERIAL PERIPHERAL INTERFACE (SPI) PHYSICAL LAYER
<!-- page: 43 -->

### External Connections
<!-- page: 43 -->

Connecting ISOMD to $V^{-}$ configures serial Port A for 4-wire SPI. The SDO pin is an open drain output which requires a pull-up resistor tied to the appropriate supply voltage (Figure 15).

### Timing

The 4-wire serial port is configured to operate in a SPI system using CPHA = 1 and CPOL = 1. Consequently, data on SDI must be stable during the rising edge of SCK. The timing is depicted in Figure 16. The maximum data rate is 1Mbps; however the device is tested at a higher data rate in production in order to guarantee operation at the maximum specified data rate.

### 2-WIRE ISOLATED INTERFACE (isoSPI) PHYSICAL LAYER
<!-- page: 43 -->

The 2-wire interface provides a means to interconnect LTC6813-1 devices using simple twisted pair cabling. The interface is designed for low packet error rates when the cabling is subjected to high RF fields. Isolation is achieved through an external transformer .

Standard SPI signals are encoded into differential pulses. The strength of the transmission pulse and the threshold level of the receiver are set by two external resistors. The values of the resistors allow the user to trade-off power dissipation for noise immunity.

Figure 17 illustrates how the isoSPI circuit operates. A 2V reference drives the IBIAS pin. External resistors $R_{B1}$ and $R_{B2}$ create the reference current $I_{B}$. This current sets the drive strength of the transmitter . $R_{B1}$ and $R_{B2}$ also form a voltage divider to supply a fraction of the 2V reference for the ICMP pin. The receiver circuit threshold is half of the voltage at the ICMP pin.


### External Connections
<!-- page: 43 -->

The LTC6813-1 has 2 serial ports which are called Port B and Port A. Port B is always configured as a 2-wire interface. Port A is either a 2-wire or 4-wire interface, depending on the connection of the ISOMD pin.

When Port A is configured as a 4-wire interface, Port A is always the SLAVE port and Port B is the MASTER port. Communication is always initiated on Port A of the first device in the daisy-chain configuration. The final device in the daisy chain does not use Port B, and it should be terminated into $R_{M}$. Figure 18 shows the simplest port connections possible when the microprocessor and the LTC6813-1s are located on the same PCB. In this figure capacitors are used to couple signals between the LTC6813-1s.

When Port A is configured as a 2-wire interface, communication can be initiated on either Port A or Port B. If communication is initiated on Port A, LTC6813-1 configures Port A as slave and Port B as master . Likewise, if communication is initiated on Port B, LTC6813-1 configures Port B as slave and Port A as master . See the section Reversible isoSPI for a detailed description of reversible isoSPI.

Figure 19 is an example of a robust interconnection of multiple identical PCBs, each containing one LTC6813-1 configured for operation in a daisy chain. The microprocessor  is  located  on  a  separate  PCB.  To  achieve 2-wire isolation between the microprocessor PCB and the 1st LTC6813-1 PCB, use the LTC6820 support IC. The LTC6820 is functionally equivalent to the diagram in Figure 17. In this example, communication is initiated on Port A. So the LTC6813-1 configures Port A as slave and Port B as master .

![Figure 15. 4-Wire SPI Configuration](ltc6813-1/figures/ltc6813-1-f070.png)

*Figure 15. 4-Wire SPI Configuration*

![Figure 16. Timing Diagram of 4-Wire Serial Peripheral Interface](ltc6813-1/figures/ltc6813-1-f071.png)

*Figure 16. Timing Diagram of 4-Wire Serial Peripheral Interface*

![Figure 17. isoSPI Interface](ltc6813-1/figures/ltc6813-1-f072.png)

*Figure 17. isoSPI Interface*

### Using a Single LTC6813-1
<!-- page: 45 -->

When only one LTC6813-1 is needed, it can be used as a single (non daisy-chained) device if the second isoSPI port (Port B) is properly biased and terminated, as shown in Figure 20 and Figure 21. ICMP should not be tied to GND, but can be tied directly to IBIAS. A bias resistance (2k to 20k) is required for IBIAS. Do not tie IBIAS directly to $V_{REG}$ or $V^{-}$. Finally, IPB and IMB should be terminated into a 100Ω resistor ( not tied to $V_{REG}$ or $V^{-}$).

68131 F19

68131 F20

![Figure 18.  Capacitive-Coupled Daisy-Chain Configuration](ltc6813-1/figures/ltc6813-1-f073.png)

*Figure 18.  Capacitive-Coupled Daisy-Chain Configuration*

![Figure 19.  T ransformer-Isolated Daisy-Chain Configuration](ltc6813-1/figures/ltc6813-1-f074.png)

*Figure 19.  T ransformer-Isolated Daisy-Chain Configuration*

![Figure 20. Single Device Using 2-Wire Port A](ltc6813-1/figures/ltc6813-1-f076.png)

*Figure 20. Single Device Using 2-Wire Port A*

![Figure 21. Single Device Using 4-Wire Port A](ltc6813-1/figures/ltc6813-1-f077.png)

*Figure 21. Single Device Using 4-Wire Port A*

### Selecting Bias Resistors
<!-- page: 48 -->

The adjustable signal amplitude allows the system to trade power consumption for communication robustness, and the adjustable comparator threshold allows the system to account for signal losses.

The  isoSPI  transmitter  drive  current  and  comparator voltage threshold are set by a resistor divider ($R_{BIAS}$ = $R_{B1}$ + $R_{B2}$) between IBIAS and $V^{-}$.  The divided voltage is connected to the ICMP pin, which sets the comparator threshold to half of this voltage ($V_{ICMP}$). When either isoSPI interface is enabled (not IDLE) IBIAS is held at 2V, causing a current $I_{B}$ to flow out of the IBIAS pin. The IP and IM pin drive currents are 20 · $I_{B}$.

As an example, if divider resistor $R_{B1}$ is 2.8k and resistor $R_{B2}$ is 1.21k (so that $R_{BIAS}$ = 4k), then:

![Equation as printed (p. 48)](ltc6813-1/figures/ltc6813-1-eq04.png)

$$I_{B} = \frac{2 V}{R_{B 1} + R_{B 2}} = \ 0.5 mA$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 48)](ltc6813-1/figures/ltc6813-1-eq05.png)

$$V_{ICMP} = 2 V \cdot \frac{R_{B 2}}{R_{B 1} + R_{B 2}} = I_{B} \cdot R_{B 2} = \ 603 mV$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 48)](ltc6813-1/figures/ltc6813-1-eq06.png)

$$I_{B} = \frac{2 V}{R_{B 1} + R_{B 2}} = \, 0.5 mA \\ I_{DRV} = I_{IP} = I_{IM} = 20 \, \cdot \, I_{B} = 10 mA \\ \cdot \\ V_{ICMP} = 2 V \, \cdot \, \frac{R_{B 2}}{R_{B 1} + R_{B 2}} = I_{B} \, \cdot \, R_{B 2} = \, 603 \\$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 48)](ltc6813-1/figures/ltc6813-1-eq07.png)

$$V_{TCMP} = 0.5 \cdot V_{ICMP} = 302 mV$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

In this example, the pulse drive current $I_{DRV}$ will be 10mA, and the receiver comparators will detect pulses with IPIM amplitudes greater than ±302mV.

If the isolation barrier uses 1:1 transformers connected by a twisted pair and terminated with 120Ω resistors on each end, then the transmitted differential signal amplitude (±) will be:

![Equation as printed (p. 48)](ltc6813-1/figures/ltc6813-1-eq08.png)

$$V_{A} = I_{DRV} \cdot \frac{R_{M}}{2} = \ 0.6 V$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

(This result ignores transformer and cable losses, which may reduce the amplitude).

### isoSPI Pulse Detail
<!-- page: 48 -->

Two LTC6813-1 devices can communicate by transmitting and receiving differential pulses back and forth through an isolation barrier . The transmitter can output three voltage levels: +$V_{A}$, 0V and -$V_{A}$. A positive output results from IP sourcing current and IM sinking current across load resistor $R_{M}$. A negative voltage is developed by IP sinking and IM sourcing. When both outputs are off, the load resistance forces the differential output to 0V.

To eliminate the DC signal component and enhance reliability, the isoSPI uses two different pulse lengths. This allows four types of pulses to be transmitted, as shown in Table 26. A +1 pulse will be transmitted as a positive pulse followed by a negative pulse. A -1 pulse will be transmitted as a negative pulse followed by a positive pulse. The duration of each pulse is defined as $t_{1/2PW}$, since each is half of the required symmetric pair . (The total isoSPI pulse duration is 2 · $t_{1/2PW}$).

**Table 26. isoSPI Pulse Types** ([table-32-p48-data.csv](ltc6813-1/tables/table-32-p48-data.csv), p. 48)

| PULSE TYPE | FIRST LEVEL ($t_{1/2PW}$) | SECOND LEVEL ($t_{1/2PW}$) | ENDING LEVEL |
|---|---|---|---|
| Long +1 | +$V_{A}$ (150ns) | −$V_{A}$ (150ns) | 0V |
| Long −1 | −$V_{A}$ (150ns) | +$V_{A}$ (150ns) | 0V |
| Short +1 | +$V_{A}$ (50ns) | −$V_{A}$ (50ns) | 0V |
| Short −1 | −$V_{A}$ (50ns) | +$V_{A}$ (50ns) | 0V |

The receiver is designed to detect each of these isoSPI pulse  types.  For  successful  detection,  the  incoming isoSPI pulses (CSB or data) should meet the following requirements:

1. $t_{1/2PW}$ of incoming pulse > $t_{FILT}$ of the receiver and 
2. $t_{INV}$ of incoming pulse < $t_{WNDW}$ of the receiver

The worst-case margin (margin 1) for the first condition is the difference between minimum $t_{1/2PW}$ of the incoming pulse and maximum $t_{FILT}$ of the receiver . Likewise, the worst-case margin (margin 2) for the second condition is the difference between minimum $t_{WNDW}$ of the receiver and maximum $t_{INV}$ of the incoming pulse. These timing relations are illustrated in Figure 22.

A host microcontroller does not have to generate isoSPI pulses to use this 2-wire interface. The first LTC6813-1 in the system can communicate to the microcontroller using the 4-wire SPI interface on its Port A, then daisy chain to other LTC6813-1s using the 2-wire isoSPI interface on its Port B. Alternatively, the LTC6820 can be used to translate the SPI signals into isoSPI pulses.

![Figure 22. isoSPI Pulse Detail](ltc6813-1/figures/ltc6813-1-f078.png)

*Figure 22. isoSPI Pulse Detail*

### Operation with Port A Configured for SPI
<!-- page: 49 -->

Table 28. Port A (Slave) isoSPI Port Function

When the LTC6813-1 is operating with Port A as a SPI (ISOMD = $V^{-}$), the SPI detects one of four communication events: CSB falling, CSB rising, SCK rising with SDI = 0 and SCK rising with SDI = 1. Each event is converted into one of the four pulse types for transmission through the daisy chain. Long pulses are used to transmit CSB changes and short pulses are used to transmit data, as explained in Table 27.

**Table 27. Port B (Master) isoSPI Port Function** ([table-33-p49-data.csv](ltc6813-1/tables/table-33-p49-data.csv), p. 49)

| COMMUNICATION EVENT (PORT A SPI) | TRANSMITTED PULSE (PORT B isoSPI) |
|---|---|
| CSB Rising | Long + 1 |
| CSB Falling | Long - 1 |
| SCK Rising Edge, SDI = 1 | Short + 1 |
| SCL Rising Edge, SDI = 0 | Short −1 |

### Operation with Port A Configured for isoSPI
<!-- page: 49 -->

On the other side of the isolation barrier (i.e., at the other end of the cable), the 2nd LTC6813-1 will have ISOMD = $V_{REG}$ so that its Port A is configured for isoSPI. The slave isoSPI port (Port A or B) receives each transmitted pulse and reconstructs the SPI signals internally, as shown in Table 28. In addition, during a READ command this port may transmit return data pulses.

**Table 28. Port A (Slave) isoSPI Port Function** ([table-34-p49-data.csv](ltc6813-1/tables/table-34-p49-data.csv), p. 49)

| RECEIVED PULSE (PORT A isoSPI) | INTERNAL SPI PORT ACTION | RETURN PULSE |
|---|---|---|
| Long +1 | Drive CSB High | None |
| Long −1 | Drive CSB Low | None |
| Short +1 | 1. Set SDI = 1 | Short - 1 Pulse, if Reading a 0 Bit, (No Return Pulse if not in READ Mode or if Reading a 1 Bit) |
| Short +1 | 2. Pulse SCK | Short - 1 Pulse, if Reading a 0 Bit, (No Return Pulse if not in READ Mode or if Reading a 1 Bit) |
| Short −1 | 1. Set SDI = 0 | Short - 1 Pulse, if Reading a 0 Bit, (No Return Pulse if not in READ Mode or if Reading a 1 Bit) |
| Short −1 | 2. Pulse SCK | Short - 1 Pulse, if Reading a 0 Bit, (No Return Pulse if not in READ Mode or if Reading a 1 Bit) |

The slave isoSPI port never transmits long (CSB) pulses. Furthermore, a slave isoSPI port will only transmit short -1 pulses, never a +1 pulse. The master port recognizes a null response as a logic 1.

### Reversible isoSPI
<!-- page: 49 -->

When the LTC6813-1 is operating with Port A configured for isoSPI, communication can be initiated from either Port A or Port B. In other words, LTC6813-1 can configure either Port A or Port B as slave or master , depending on the direction of communication. The reversible isoSPI feature permits communication from both directions in a stack of daisy-chained devices. See Figure 23 for an example schematic. Figure 24 illustrates the operation of reversible isoSPI.

68131 F23

When LTC6813-1 is in SLEEP state, it will respond to a valid WAKE-UP signal on either Port A or Port B. This is true for either configuration of the ISOMD pin.

If the WAKE-UP signal was sent on Port A, LTC6813-1 transmits a long +1 isoSPI pulse (CSB rising) on Port B after the isoSPI is powered up. If the WAKE-UP signal was sent on Port B, LTC6813-1 powers up the isoSPI but does not transmit a long +1 isoSPI pulse on Port A.

When LTC6813-1 is in READY state, communication can be initiated by sending a long -1 isoSPI pulse (CSB falling) on either Port A or Port B. The LTC6813-1 automatically configures the port that receives the long -1 isoSPI pulse as the slave and the other port is configured as the master. The isoSPI pulses are transmitted through the master port to the rest of the devices in the daisy chain.

In ACTIVE state, the LTC6813-1 is in the middle of communication and CSB of the internal SPI port is low. At the end of communication a long +1 pulse (CSB rising) on the SLAVE port returns the part to the READY state. Although it is not part of a normal communication routine, the LTC6813-1 allows ports A and B to be swapped inside the ACTIVE state. This feature is useful for the master controller to reclaim control of the slave port of LTC6813-1 irrespective of the current state of the ports. This can be done by sending a long -1 isoSPI pulse on the master port after a time delay of $t_{BLOCK}$ from the last isoSPI signal that was transmitted by the part. Any long isoSPI pulse sent to the master port inside $t_{BLOCK}$ is rejected by the part. This ensures the LTC6813-1 cannot switch ports because of signal reflections from poorly terminated cables (<100m cable length).

![Figure 23. Reversible isoSPI Daisy Chain](ltc6813-1/figures/ltc6813-1-f079.png)

*Figure 23. Reversible isoSPI Daisy Chain*

![Figure 24. Reversible isoSPI State Diagram](ltc6813-1/figures/ltc6813-1-f081.png)

*Figure 24. Reversible isoSPI State Diagram*

### Timing Diagrams
<!-- page: 51 -->

Figure 25 shows the isoSPI timing diagram for a READ command to daisy-chained LTC6813-1 parts. The ISOMD pin is tied to V -on the bottom part so its Port A is configured as a SPI port (CSB, SCK, SDI and SDO). The isoSPI signals of three stacked devices are shown labeled with the port (A or B) and part number . Note that ISO B1 and ISO A2 is actually the same signal, but shown on each end of the transmission cable that connects Parts 1 and 2. Likewise, ISO B2 and ISO A3 is the same signal, but with the cable delay shown between Parts 2 and 3.

Bits $W_{N}$ -$W_{0}$ refer to the 16-bit command code and the 16-bit PEC of a READ command. At the end of Bit $W_{0}$, the three parts decode the READ command and begin shifting out data, which is valid on the next rising edge of clock SCK. Bits $X_{N}$ -$X_{0}$ refer to the data shifted out by Part 1. Bits $Y_{N}$ -$Y_{0}$ refer to the data shifted out by Part 2 and bits $Z_{N}$ -$Z_{0}$ refer to the data shifted out by Part 3. All this data is read back from the SDO port on Part 1 in a daisy-chained fashion.

![Figure 25. isoSPI Timing Diagram](ltc6813-1/figures/ltc6813-1-f082.png)

*Figure 25. isoSPI Timing Diagram*

### Waking Up the Serial Interface
<!-- page: 53 -->

The serial ports (SPI or isoSPI) will enter the low power IDLE state if there is no activity on Port A or Port B for a time of $t_{IDLE}$. The WAKE-UP circuit monitors activity on pins 61 through 64.

If ISOMD = $V^{-}$, Port A is in SPI mode. Activity on the CSB or SCK pin will wake up the SPI interface. If ISOMD = $V_{REG}$, Port A is in isoSPI mode. Differential activity on IPA-IMA (or IPB-IMB) wakes up the isoSPI interface. The LTC6813-1 will be ready to communicate when the isoSPI state changes to READY within $t_{WAKE}$ or $t_{READY}$, depending on the Core state (see Figure 1 and state descriptions for details).

Figure  26  illustrates  the  timing  and  the  functionally equivalent circuit (only Port A shown). Common mode signals will not wake up the serial interface. The interface is designed to wake up after receiving a large signal single-ended pulse, or a low-amplitude symmetric pulse. The differential signal |SCK(IPA) - CSB(IMA)|, must be at least $V_{WAKE}$ = 200mV for a minimum duration of $t_{DWELL}$ = 240ns to qualify as a WAKE-UP signal that powers up the serial interface.

### Waking a Daisy Chain-Method 1
<!-- page: 53 -->

The LTC6813-1 sends a long +1 pulse on Port B after it is ready to communicate. In a daisy-chained configuration, this pulse wakes up the next device in the stack which will, in turn, wake up the next device. If there are 'N' devices in the stack, all the devices are powered up within the time N · $t_{WAKE}$ or N · $t_{READY}$, depending on the Core state. For large stacks, the time N · $t_{WAKE}$ may be equal to or larger than $t_{IDLE}$. In this case, after waiting longer than the time of N · $t_{WAKE}$, the host may send another dummy byte and wait for the time N · $t_{READY}$, in order to ensure that all devices are in the READY state.

Method 1 can be used when all devices on the daisy chain are in the IDLE state. This guarantees that they propagate the WAKE-UP signal up the daisy chain. However , this method will fail to wake up all devices when a device in the middle of the chain is in the READY state instead of IDLE. When this happens, the device in READY state will not propagate the wake-up pulse, so the devices above it will remain IDLE. This situation can occur when attempting to wake up the daisy chain after only $t_{IDLE}$ of idle time (some devices may be IDLE, some may not).

![Figure 26. Wake-Up Detection and IDLE Timer](ltc6813-1/figures/ltc6813-1-f084.png)

*Figure 26. Wake-Up Detection and IDLE Timer*

### Waking a Daisy Chain-Method 2
<!-- page: 54 -->

A more robust wake-up method does not rely on the builtin wake-up pulse, but manually sends isoSPI traffic for enough time to wake the entire daisy chain. At minimum, a pair of long isoSPI pulses (-1 and +1) is needed for each device, separated by more than $t_{READY}$ or $t_{WAKE}$ (if the Core state is STANDBY or SLEEP , respectively), but less than $t_{IDLE}$. This allows each device to wake up and propagate the next pulse to the following device. This method works even if some devices in the chain are not in the IDLE state. In practice, implementing method 2 requires toggling the CSB pin (of the LTC6820, or bottom LTC6813-1 with ISOMD = 0) to generate the long isoSPI pulses. Alternatively, dummy commands (such as RDCFGA) can be executed to generate the long isoSPI pulses.

### DATA LINK LAYER
<!-- page: 54 -->

All data transfers on LTC6813-1 occur in byte groups. Every byte consists of 8 bits. Bytes are transferred with the most significant bit (MSB) first. CSB must remain low for the entire duration of a command sequence, including between a command byte and subsequent data. On a write command, data is latched in on the rising edge of CSB.

### NETWORK LAYER
<!-- page: 54 -->

### Packet Error Code
<!-- page: 54 -->

The Packet Error Code (PEC) is a 15-bit cyclic redundancy check (CRC) value calculated for all of the bits in a register group in the order they are passed, using the initial PEC value of 000000000010000 and the following characteristic polynomial: $x^{15} + x^{14} + x^{10} + x^{8} + x^{7} + x^{4} + x^{3} + 1$ . To calculate the 15-bit PEC value, a simple procedure can be established:

1. Initialize  the  PEC  to  000000000010000 (PEC is a 15-bit register group).
2. For each bit DIN coming into the PEC register group, set;

```
IN0 = DIN XOR PEC[14]
IN3 = IN0 XOR PEC[2]
IN4 = IN0 XOR PEC[3]
IN7 = IN0 XOR PEC[6]
IN8 = IN0 XOR PEC[7]
IN10 = IN) XOR PEC[9]
IN14 = IN0 XOR PEC[13]
```

3. Update the 15-bit PEC as follows:

```
PEC[14] = IN14 
PEC[13] = PEC[12]
PEC[12] = PEC[11]
PEC[11] = PEC[10]
PEC[10] = IN10 
PEC[9] = PEC[8] 
PEC[8] = IN8 
PEC[7] = IN7 
PEC[6] = PEC[5] 
PEC[5] = PEC[4] 
PEC[4] = IN4 
PEC[3] = IN3 
PEC[2] = PEC[1] 
PEC[1] = PEC[0] 
PEC[0] = IN0
```

4. Go back to step 2 until all the data is shifted. The final PEC (16 bits) is the 15-bit value in the PEC register with a 0 bit appended to its LSB.

Figure 27 illustrates the algorithm described above. An example to calculate the PEC for a 16-bit word (0x0001) is listed in Table 29. The PEC for 0x0001 is computed as 0x3D6E after stuffing a 0 bit at the LSB. For longer data streams, the PEC is valid at the end of the last bit of data sent to the PEC register .

LTC6813-1 calculates PEC for any command or data received and compares it with the PEC following the command or data. The command or data is regarded as valid only if the PEC matches. LTC6813-1 also attaches the calculated PEC at the end of the data it shifts out. Table 30 shows the format of PEC while writing to or reading from LTC6813-1.

### Table 29. PEC Calculation for 0x0001
<!-- page: 55 -->

**Table 29. PEC Calculation for 0x0001** ([table-35-p55-data.csv](ltc6813-1/tables/table-35-p55-data.csv), p. 55)

|  | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | PEC Word |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PEC[14] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 |
| PEC[13] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 0 |
| PEC[12] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 1 |
| PEC[11] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 1 |
| PEC[10] | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 1 | 1 |
| PEC[9] | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 1 |
| PEC[8] | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 | 0 |
| PEC[7] | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 1 | 1 | 1 |
| PEC[6] | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 |
| PEC[5] | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 1 |
| PEC[4] | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 1 | 1 |
| PEC[3] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 0 | 0 | 0 |
| PEC[2] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 |
| PEC[1] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 |
| PEC[0] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| IN14 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | | 0 |
| IN10 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 1 | | PEC Word |
| IN8 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 | | |
| IN7 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 1 | 1 | | |
| IN4 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 1 |  |  |
| IN3 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 0 | 0 | | |
| IN0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 |  |  |
| DIN | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 |  |  |
| Clock Cycle | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |  |

### Table 30. Write/Read PEC Format
<!-- page: 55 -->

**Table 30. Write/Read PEC Format** ([table-36-p55-register.csv](ltc6813-1/tables/table-36-p55-register.csv), p. 55)

| NAME | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| PEC0 | RD/WR | PEC[14] | PEC[13] | PEC[12] | PEC[11] | PEC[10] | PEC[9] | PEC[8] | PEC[7] |
| PEC1 | RD/WR | PEC[6] | PEC[5] | PEC[4] | PEC[3] | PEC[2] | PEC[1] | PEC[0] | 0 |

While writing any command to LTC6813-1, the command bytes CMD0 and CMD1 (see Table 37 and Table 38) and the PEC bytes PEC0 and PEC1 are sent on Port A in the following order:

```
CMD0, CMD1, PEC0, PEC1
```

After  a  write  command  to  daisy-chained  LTC6813-1 devices,  data  is  sent  to  each  device  followed  by  the PEC. For example, when writing Configuration Register Group A to two daisy-chained devices (primary device P , stacked device S), the data will be sent to the primary device on Port A in the following order:

```
CFGAR0(S), … , CFGAR5(S), PEC0(S), PEC1(S), 
CFGAR0(P), … , CFGAR5(P), PEC0(P), PEC1(P)
```

After a read command for daisy-chained devices, each device shifts out its data and the PEC that it computed for its data on Port A followed by the data received on Port B. For example, when reading Status Register Group B from two daisy-chained devices (primary device P , stacked device S), the primary device sends out data on port A in the following order:

```
STBR0(P), … , STBR5(P), PEC0(P), PEC1(P), 
STBR0(S), … , STBR5(S), PEC0(S), PEC1(S)
```
See Bus Protocols for command format.

All devices in a daisy-chained configuration receive the command bytes simultaneously. For example, to initiate ADC conversions in a stack of devices, a single ADCV command is sent, and all devices will start conversions at the same time. For read and write commands, a single command is sent, and then the stacked devices effectively turn into a cascaded shift register , in which data is shifted through each device to the next higher (on a write) or the next lower (on a read) device in the stack. See the Serial Interface Overview section.

![Figure 27. 15-Bit PEC Computation Circuit](ltc6813-1/figures/ltc6813-1-f085.png)

*Figure 27. 15-Bit PEC Computation Circuit*

### Polling Methods
<!-- page: 56 -->

The simplest method to determine ADC completion is for the controller to start an ADC conversion and wait for the specified conversion time to pass before reading the results.

If using a single LTC6813-1 that communicates in SPI mode (ISOMD pin tied low), there are two methods of polling. The first method is to hold CSB low after an ADC conversion command is sent. After entering a conversion command, the SDO line is driven low when the device is busy performing conversions. SDO is pulled high when the device completes conversions. However , SDO will also go back high when CSB goes high even if the device has not completed the conversion (Figure 28). A problem with this method is that the controller is not free to do other serial communication while waiting for ADC conversions to complete.

The next method overcomes this limitation. The controller can send an ADC start command, perform other tasks, and then send a poll ADC converter status (PLADC) command to determine the status of the ADC conversions (Figure 29). After entering the PLADC command, SDO will go low if the device is busy performing conversions. SDO is pulled high at the end of conversions. However , SDO will also go high when CSB goes high even if the device has not completed the conversion.

If using a single LTC6813-1 that communicates in isoSPI mode, the low side port transmits a data pulse only in response to a master isoSPI pulse received by it. So, after entering the command in either method of polling described above, isoSPI data pulses are sent to the part to update the conversion status. These pulses can be sent using LTC6820 by simply clocking its SCK pin. In response to this pulse, the LTC6813-1 sends back a low isoSPI pulse if it is still busy performing conversions or a high data pulse if it has completed the conversions. If a CSB high isoSPI pulse is sent to the device, it exits the polling command.

In a daisy-chained configuration of N stacked devices, the same two polling methods can be used. If the bottom device communicates in SPI mode, the SDO of the bottom device indicates the conversion status of the entire stack. i.e., SDO will remain low until all the devices in the stack have completed the conversions. In the first method of polling, after an ADC conversion command is sent, clock pulses are sent on SCK while keeping CSB low. The SDO status becomes valid only at the end of N clock pulses on SCK. During the first N clock pulses, the bottom LTC6813-1 in the daisy chain will output a 0 or a low data pulse. After N clock pulses, the output data from the bottom LTC6813-1 gets updated for every clock pulse that follows (Figure 30). In the second method, the PLADC command is sent followed by clock pulses on SCK while keeping CSB low. Similar to the first method, the SDO status is valid only after N clock cycles on SCK and gets updated after every clock cycle that follows (Figure 31). If  the  bottom  device  communicates  in  isoSPI  mode, isoSPI data pulses are sent to the device to update the conversion status. Using LTC6820, this can be achieved by just clocking its SCK pin. The conversion status is valid only after the bottom LTC6813-1 device receives N isoSPI data pulses and the status gets updated for every isoSPI data pulse that follows. The device returns a low data pulse if any of the devices in the stack is busy performing conversions and returns a high data pulse if all the devices are free.

![Figure 28. SDO Polling After an ADC Conversion Command (Single LTC6813-1)](ltc6813-1/figures/ltc6813-1-f088.png)

*Figure 28. SDO Polling After an ADC Conversion Command (Single LTC6813-1)*

![Figure 29. SDO Polling Using PLADC Command (Single LTC6813-1)](ltc6813-1/figures/ltc6813-1-f089.png)

*Figure 29. SDO Polling Using PLADC Command (Single LTC6813-1)*

![Figure 30. SDO Polling After an ADC Conversion Command (Daisy-Chain Configuration)](ltc6813-1/figures/ltc6813-1-f090.png)

*Figure 30. SDO Polling After an ADC Conversion Command (Daisy-Chain Configuration)*

![Figure 31. SDO Polling Using PLADC Command (Daisy-Chain Configuration)](ltc6813-1/figures/ltc6813-1-f091.png)

*Figure 31. SDO Polling Using PLADC Command (Daisy-Chain Configuration)*

### Bus Protocols
<!-- page: 56 -->

Protocol Format: The protocol formats for commands are depicted in Tables 32 through 34. Table 31 is the key for reading the protocol diagrams.

### Table 31. Protocol Key
<!-- page: 59 -->

**Table 31. Protocol Key** ([table-37-p59-data.csv](ltc6813-1/tables/table-37-p59-data.csv), p. 59)

| PARAMETER | DESCRIPTION |
|---|---|
| CMD0 | Command Byte 0 (See Table 35) |
| CMD1 | Command Byte 1 (See Table 35) |
| PEC0 | Packet Error Code Byte 0 (See Table 30) |
| PEC1 | Packet Error Code Byte 1 (See Table 30) |
| n | Number of Bytes |
| … | Continuation of Protocol |
|  | Master to Slave |
|  | Slave to Master |

**Table 32. Poll Command** ([table-38-p59-data.csv](ltc6813-1/tables/table-38-p59-data.csv), p. 59)

| CMD0 | CMD1 | PEC0 | PEC1 | Poll Data |
|---|---|---|---|---|
| 8 | 8 | 8 | 8 |  |

### Table 33. Write Command
<!-- page: 59 -->

| 8    | 8    | 8    | 8    | 8             |    | 8              | 8    | 8    | 8            |    | 8            |
|------|------|------|------|---------------|----|----------------|------|------|--------------|----|--------------|
| CMD0 | CMD1 | PEC0 | PEC1 | Data Byte Low | …  | Data Byte High | PEC0 | PEC1 | Shift Byte 1 | …  | Shift Byte n |

### Table 34. Read Command
<!-- page: 59 -->

| 8    | 8    | 8    | 8    | 8             |    | 8              | 8    | 8    | 8            |    | 8            |
|------|------|------|------|---------------|----|----------------|------|------|--------------|----|--------------|
| CMD0 | CMD1 | PEC0 | PEC1 | Data Byte Low | …  | Data Byte High | PEC0 | PEC1 | Shift Byte 1 | …  | Shift Byte n |

### Table 35. Command Format
<!-- page: 59 -->

**Table 35. Command Format** ([table-41-p59-register.csv](ltc6813-1/tables/table-41-p59-register.csv), p. 59)

| NAME | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CMD0 | WR | 0 | 0 | 0 | 0 | 0 | CC[10] | CC[9] | CC[8] |
| CMD1 | WR | CC[7] | CC[6] | CC[5] | CC[4] | CC[3] | CC[2] | CC[1] | CC[0] |

### Commands
<!-- page: 59 -->

Command Format: The format for the commands is shown in Table 35. CC[10:0] is the 11-bit command code. A list of all the command codes is shown in Table 36. All commands have a value 0 for CMD0[7] through CMD0[3]. The PEC must be computed on the entire 16-bit command (CMD0 and CMD1).

Table 36 lists all the commands and their options.

| COMMAND DESCRIPTION                  |         |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |   CC[10:0] - COMMAND CODE |
|--------------------------------------|---------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|---------------------------|
| COMMAND DESCRIPTION                  | NAME    |                        10 |                         9 |                         8 |                         7 |                         6 |                         5 |                         4 |                         3 |                         2 |                         1 |                         0 |
| Write Configuration Register Group A | WRCFGA  |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |
| Write Configuration Register Group B | WRCFGB  |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         1 |                         0 |                         0 |
| Read Configuration Register Group A  | RDCFGA  |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |
| Read Configuration Register Group B  | RDCFGB  |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         1 |                         1 |                         0 |
| Read Cell Voltage Register Group A   | RDCVA   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |
| Read Cell Voltage Register Group B   | RDCVB   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         0 |
| Read Cell Voltage Register Group C   | RDCVC   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         0 |
| Read Cell Voltage Register Group D   | RDCVD   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         1 |                         0 |
| Read Cell Voltage Register Group E   | RDCVE   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         1 |
| Read Cell Voltage Register Group F   | RDCVF   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         1 |                         1 |
| Read Auxiliary Register Group A      | RDAUXA  |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         0 |                         0 |
| Read Auxiliary Register Group B      | RDAUXB  |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         1 |                         0 |
| Read Auxiliary Register Group C      | RDAUXC  |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         0 |                         1 |
| Read Auxiliary Register Group D      | RDAUXD  |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         1 |                         1 |
| Read Status Register Group A         | RDSTATA |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         0 |                         0 |
| Read Status Register Group B         | RDSTATB |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         1 |                         0 |
| Write S Control Register Group       | WRSCTRL |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         1 |                         0 |                         0 |
| Write PWM Register Group             | WRPWM   |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         0 |                         0 |                         0 |
| Write PWM/S Control Register Group B | WRPSB   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         1 |                         0 |                         0 |
| Read S Control Register Group        | RDSCTRL |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         1 |                         1 |                         0 |
| Read PWM Register Group              | RDPWM   |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         0 |                         0 |                         0 |                         1 |                         0 |
| Read PWM/S Control Register Group B  | RDPSB   |                         0 |                         0 |                         0 |                         0 |                         0 |                         0 |                         1 |                         1 |                         1 |                         1 |                         0 |

**Table 36. Command Codes** ([table-42-p60-data.csv](ltc6813-1/tables/table-42-p60-data.csv), p. 60)

| COMMAND DESCRIPTION | NAME | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| **CC[10:0] – COMMAND CODE** |  |  |  |  |  |  |  |  |  |  |  |  |
| Write Configuration Register Group A | WRCFGA | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 |
| Write Configuration Register Group B | WRCFGB | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 0 | 0 |
| Read Configuration Register Group A | RDCFGA | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 |
| Read Configuration Register Group B | RDCFGB | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 | 0 |
| Read Cell Voltage Register Group A | RDCVA | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 |
| Read Cell Voltage Register Group B | RDCVB | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 0 |
| Read Cell Voltage Register Group C | RDCVC | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 |
| Read Cell Voltage Register Group D | RDCVD | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 |
| Read Cell Voltage Register Group E | RDCVE | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 |
| Read Cell Voltage Register Group F | RDCVF | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 1 |
| Read Auxiliary Register Group A | RDAUXA | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 0 |
| Read Auxiliary Register Group B | RDAUXB | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 0 |
| Read Auxiliary Register Group C | RDAUXC | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 1 |
| Read Auxiliary Register Group D | RDAUXD | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 |
| Read Status Register Group A | RDSTATA | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 |
| Read Status Register Group B | RDSTATB | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 0 |
| Write S Control Register Group | WRSCTRL | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 0 |
| Write PWM Register Group | WRPWM | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 |
| Write PWM/S Control Register Group B | WRPSB | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 0 |
| Read S Control Register Group | RDSCTRL | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 1 | 0 |
| Read PWM Register Group | RDPWM | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 |
| Read PWM/S Control Register Group B | RDPSB | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 0 |
| Start S Control Pulsing and Poll Status | STSCTRL | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 1 |
| Clear S Control Register Group | CLRSCTRL | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 0 |
| Start Cell Voltage ADC Conversion and Poll Status | ADCV | 0 | 1 | MD[1] | MD[0] | 1 | 1 | DCP | 0 | CH[2] | CH[1] | CH[0] |
| Start Open Wire ADC Conversion and Poll Status | ADOW | 0 | 1 | MD[1] | MD[0] | PUP | 1 | DCP | 1 | CH[2] | CH[1] | CH[0] |
| Start Self Test Cell Voltage Conversion and Poll Status | CVST | 0 | 1 | MD[1] | MD[0] | ST[1] | ST[0] | 0 | 0 | 1 | 1 | 1 |
| Start Overlap Measurements of Cell 7 and Cell 13 Voltages | ADOL | 0 | 1 | MD[1] | MD[0] | 0 | 0 | DCP | 0 | 0 | 0 | 1 |
| Start GPIOs ADC Conversion and Poll Status | ADAX | 1 | 0 | MD[1] | MD[0] | 1 | 1 | 0 | 0 | CHG[2] | CHG[1] | CHG[0] |
| Start GPIOs ADC Conversion with Digital Redundancy and Poll Status | ADAXD | 1 | 0 | MD[1] | MD[0] | 0 | 0 | 0 | 0 | CHG[2] | CHG[1] | CHG[0] |
| Start GPIOs Open Wire ADC Conversion and Poll Status | AXOW | 1 | 0 | MD[1] | MD[0] | PUP | 0 | 1 | 0 | CHG[2] | CHG[1] | CHG[0] |
| Start Self Test GPIOs Conversion and Poll Status | AXST | 1 | 0 | MD[1] | MD[0] | ST[1] | ST[0] | 0 | 0 | 1 | 1 | 1 |
| Start Status Group ADC Conversion and Poll Status | ADSTAT | 1 | 0 | MD[1] | MD[0] | 1 | 1 | 0 | 1 | CHST[2] | CHST[1] | CHST[0] |
| Start Status Group ADC Conversion with Digital Redundancy and Poll Status | ADSTATD | 1 | 0 | MD[1] | MD[0] | 0 | 0 | 0 | 1 | CHST[2] | CHST[1] | CHST[0] |
| Start Self Test Status Group Conversion and Poll Status | STATST | 1 | 0 | MD[1] | MD[0] | ST[1] | ST[0] | 0 | 1 | 1 | 1 | 1 |
| Start Combined Cell Voltage and GPIO1, GPIO2 Conversion and Poll Status | ADCVAX | 1 | 0 | MD[1] | MD[0] | 1 | 1 | DCP | 1 | 1 | 1 | 1 |
| Start Combined Cell Voltage and SC Conversion and Poll Status | ADCVSC | 1 | 0 | MD[1] | MD[0] | 1 | 1 | DCP | 0 | 1 | 1 | 1 |
| Clear Cell Voltage Register Groups | CLRCELL | 1 | 1 | 1 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 |
| Clear Auxiliary Register Groups | CLRAUX | 1 | 1 | 1 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 0 |
| Clear Status Register Groups | CLRSTAT | 1 | 1 | 1 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 |
| Poll ADC Conversion Status | PLADC | 1 | 1 | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 0 |
| Diagnose MUX and Poll Status | DIAGN | 1 | 1 | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 |
| Write COMM Register Group | WRCOMM | 1 | 1 | 1 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 |
| Read COMM Register Group | RDCOMM | 1 | 1 | 1 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 |
| Start $I^{2}C$/SPI Communication | STCOMM | 1 | 1 | 1 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 1 |
| Mute Discharge | MUTE | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 0 | 0 |
| Unmute Discharge | UNMUTE | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 0 | 1 |

### Table 37. Command Bit Descriptions
<!-- page: 62 -->

**Table 37. Command Bit Descriptions** ([table-43-p62-register.csv](ltc6813-1/tables/table-43-p62-register.csv), p. 62)

| NAME | DESCRIPTION | VALUES | SETTING | 27kHz | 14kHz | 7kHz | 3kHz | 2kHz | 1kHz | 422Hz | 26Hz |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MD[1:0] | ADC Mode | MD | ADCOPT(CFGAR0[0]) = 0 | ADCOPT(CFGAR0[0]) = 1 |  |  |  |  |  |  |  |
| MD[1:0] | ADC Mode | 00 | 422Hz Mode | 1kHz Mode |  |  |  |  |  |  |  |
| MD[1:0] | ADC Mode | 01 | 27kHz Mode (Fast) | 14kHz Mode |  |  |  |  |  |  |  |
| MD[1:0] | ADC Mode | 10 | 7kHz Mode (Normal) | 3kHz Mode |  |  |  |  |  |  |  |
| MD[1:0] | ADC Mode | 11 | 26Hz Mode (Filtered) | 2kHz Mode |  |  |  |  |  |  |  |
| DCP | Discharge Permitted | DCP |  |  |  |  |  |  |  |  |  |
| DCP | Discharge Permitted | 0 | Discharge Not Permitted |  |  |  |  |  |  |  |  |
| DCP | Discharge Permitted | 1 | Discharge Permitted |  |  |  |  |  |  |  |  |
| CH[2:0] | Cell Selection for ADC Conversion |  |  | Total Conversion Time in the 8 ADC Modes |  |  |  |  |  |  |  |
| CH[2:0] | Cell Selection for ADC Conversion | CH |  | 27kHz | 14kHz | 7kHz | 3kHz | 2kHz | 1kHz | 422Hz | 26Hz |
| CH[2:0] | Cell Selection for ADC Conversion | 000 | All Cells | 1.1ms | 1.3ms | 2.3ms | 3.0ms | 4.4ms | 7.2ms | 12.8ms | 201ms |
| CH[2:0] | Cell Selection for ADC Conversion | 001 | Cells 1, 7, 13 | 203µs | 232µs | 407µs | 523µs | 756µs | 1.2ms | 2.2ms | 34ms |
| CH[2:0] | Cell Selection for ADC Conversion | 010 | Cells 2, 8, 14 | 203µs | 232µs | 407µs | 523µs | 756µs | 1.2ms | 2.2ms | 34ms |
| CH[2:0] | Cell Selection for ADC Conversion | 011 | Cells 3, 9, 15 | 203µs | 232µs | 407µs | 523µs | 756µs | 1.2ms | 2.2ms | 34ms |
| CH[2:0] | Cell Selection for ADC Conversion | 100 | Cells 4, 10, 16 | 203µs | 232µs | 407µs | 523µs | 756µs | 1.2ms | 2.2ms | 34ms |
| CH[2:0] | Cell Selection for ADC Conversion | 101 | Cells 5, 11, 17 | 203µs | 232µs | 407µs | 523µs | 756µs | 1.2ms | 2.2ms | 34ms |
| CH[2:0] | Cell Selection for ADC Conversion | 110 | Cells 6, 12, 18 | 203µs | 232µs | 407µs | 523µs | 756µs | 1.2ms | 2.2ms | 34ms |
| PUP | Pull-Up/Pull-Down Current for Open Wire Conversions | PUP |  |  |  |  |  |  |  |  |  |
| PUP | Pull-Up/Pull-Down Current for Open Wire Conversions | 0 | Pull-Down Current |  |  |  |  |  |  |  |  |
| PUP | Pull-Up/Pull-Down Current for Open Wire Conversions | 1 | Pull-Up Current |  |  |  |  |  |  |  |  |
| ST[1:0] | Self Test Mode Selection |  |  | Self Test Conversion Result |  |  |  |  |  |  |  |
| ST[1:0] | Self Test Mode Selection | ST |  | 27kHz | 14kHz | 7kHz | 3kHz | 2kHz | 1kHz | 422Hz | 26Hz |
| ST[1:0] | Self Test Mode Selection | 01 | Self Test 1 | 0x9565 | 0x9553 | 0x9555 | 0x9555 | 0x9555 | 0x9555 | 0x9555 | 0x9555 |
| ST[1:0] | Self Test Mode Selection | 10 | Self test 2 | 0x6A9A | 0x6AAC | 0x6AAA | 0x6AAA | 0x6AAA | 0x6AAA | 0x6AAA | 0x6AAA |
| CHG[2:0] | GPIO Selection for ADC Conversion |  |  | Total Conversion Time in the 8 ADC Modes |  |  |  |  |  |  |  |
| CHG[2:0] | GPIO Selection for ADC Conversion | CHG |  | 27kHz | 14kHz | 7kHz | 3kHz | 2kHz | 1kHz | 422Hz | 26Hz |
| CHG[2:0] | GPIO Selection for ADC Conversion | 000 | GPIO 1–5, 2nd Reference, GPIO 6–9 | 1.8ms | 2.1ms | 3.9ms | 5.0ms | 7.4ms | 12.0ms | 21.3ms | 335ms |
| CHG[2:0] | GPIO Selection for ADC Conversion | 001 | GPIO 1 and GPIO 6 | 380µs | 439µs | 788µs | 1.0ms | 1.5ms | 2.4ms | 4.3ms | 67.1ms |
| CHG[2:0] | GPIO Selection for ADC Conversion | 010 | GPIO 2 and GPIO 7 | 380µs | 439µs | 788µs | 1.0ms | 1.5ms | 2.4ms | 4.3ms | 67.1ms |
| CHG[2:0] | GPIO Selection for ADC Conversion | 011 | GPIO 3 and GPIO 8 | 380µs | 439µs | 788µs | 1.0ms | 1.5ms | 2.4ms | 4.3ms | 67.1ms |
| CHG[2:0] | GPIO Selection for ADC Conversion | 100 | GPIO 4 and GPIO 9 | 380µs | 439µs | 788µs | 1.0ms | 1.5ms | 2.4ms | 4.3ms | 67.1ms |
| CHG[2:0] | GPIO Selection for ADC Conversion | 101 | GPIO 5 | 200µs | 229µs | 403µs | 520µs | 753µs | 1.2ms | 2.1ms | 34ms |
| CHG[2:0] | GPIO Selection for ADC Conversion | 110 | 2nd Reference | 200µs | 229µs | 403µs | 520µs | 753µs | 1.2ms | 2.1ms | 34ms |
| CHST[2:0]* | Status Group Selection |  |  | Total Conversion Time in the 8 ADC Modes |  |  |  |  |  |  |  |
| CHST[2:0]* | Status Group Selection | CHST |  | 27kHz | 14kHz | 7kHz | 3kHz | 2kHz | 1kHz | 422Hz | 26Hz |
| CHST[2:0]* | Status Group Selection | 000 | SC, ITMP, VA, VD | 742µs | 858µs | 1.6ms | 2.0ms | 3.0ms | 4.8ms | 8.5ms | 134ms |
| CHST[2:0]* | Status Group Selection | 001 | SC | 200µs | 229µs | 403µs | 520µs | 753µs | 1.2ms | 2.1ms | 34ms |
| CHST[2:0]* | Status Group Selection | 010 | ITMP | 200µs | 229µs | 403µs | 520µs | 753µs | 1.2ms | 2.1ms | 34ms |
| CHST[2:0]* | Status Group Selection | 011 | VA | 200µs | 229µs | 403µs | 520µs | 753µs | 1.2ms | 2.1ms | 34ms |
| CHST[2:0]* | Status Group Selection | 100 | VD | 200µs | 229µs | 403µs | 520µs | 753µs | 1.2ms | 2.1ms | 34ms |

- **\*:** Note: Valid options for CHST in ADSTAT command are 0–4. If CHST is set to 5/6 in ADSTAT command, the LTC6813-1 ignores the command.

### Memory Map
<!-- page: 63 -->

### Table 38. Configuration Register Group A
<!-- page: 63 -->

**Table 38. Configuration Register Group A** ([table-44-p63-register.csv](ltc6813-1/tables/table-44-p63-register.csv), p. 63)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CFGAR0 | RD/WR | GPIO5 | GPIO4 | GPIO3 | GPIO2 | GPIO1 | REFON | DTEN | ADCOPT |
| CFGAR1 | RD/WR | VUV[7] | VUV[6] | VUV[5] | VUV[4] | VUV[3] | VUV[2] | VUV[1] | VUV[0] |
| CFGAR2 | RD/WR | VOV[3] | VOV[2] | VOV[1] | VOV[0] | VUV[11] | VUV[10] | VUV[9] | VUV[8] |
| CFGAR3 | RD/WR | VOV[11] | VOV[10] | VOV[9] | VOV[8] | VOV[7] | VOV[6] | VOV[5] | VOV[4] |
| CFGAR4 | RD/WR | DCC8 | DCC7 | DCC6 | DCC5 | DCC4 | DCC3 | DCC2 | DCC1 |
| CFGAR5 | RD/WR | DCTO[3] | DCTO[2] | DCTO[1] | DCTO[0] | DCC12 | DCC11 | DCC10 | DCC9 |

### Table 39. Configuration Register Group B
<!-- page: 63 -->

**Table 39. Configuration Register Group B** ([table-45-p63-register.csv](ltc6813-1/tables/table-45-p63-register.csv), p. 63)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CFGBR0 | RD/WR | DCC16 | DCC15 | DCC14 | DCC13 | GPIO9 | GPIO8 | GPIO7 | GPIO6 |
| CFGBR1 | RD/WR | MUTE | FDRF | PS[1] | PS[0] | DTMEN | DCC0 | DCC18 | DCC17 |
| CFGBR2 | RD/WR | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 |
| CFGBR3 | RD/WR | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 |
| CFGBR4 | RD/WR | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 |
| CFGBR5 | RD/WR | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 | RSVD0 |

### Table 40. Cell Voltage Register Group A
<!-- page: 63 -->

**Table 40. Cell Voltage Register Group A** ([table-46-p63-register.csv](ltc6813-1/tables/table-46-p63-register.csv), p. 63)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CVAR0 | RD | C1V[7] | C1V[6] | C1V[5] | C1V[4] | C1V[3] | C1V[2] | C1V[1] | C1V[0] |
| CVAR1 | RD | C1V[15] | C1V[14] | C1V[13] | C1V[12] | C1V[11] | C1V[10] | C1V[9] | C1V[8] |
| CVAR2 | RD | C2V[7] | C2V[6] | C2V[5] | C2V[4] | C2V[3] | C2V[2] | C2V[1] | C2V[0] |
| CVAR3 | RD | C2V[15] | C2V[14] | C2V[13] | C2V[12] | C2V[11] | C2V[10] | C2V[9] | C2V[8] |
| CVAR4 | RD | C3V[7] | C3V[6] | C3V[5] | C3V[4] | C3V[3] | C3V[2] | C3V[1] | C3V[0] |
| CVAR5 | RD | C3V[15] | C3V[14] | C3V[13] | C3V[12] | C3V[11] | C3V[10] | C3V[9] | C3V[8] |

### Table 41. Cell Voltage Register Group B
<!-- page: 63 -->

**Table 41. Cell Voltage Register Group B** ([table-47-p63-register.csv](ltc6813-1/tables/table-47-p63-register.csv), p. 63)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CVBR0 | RD | C4V[7] | C4V[6] | C4V[5] | C4V[4] | C4V[3] | C4V[2] | C4V[1] | C4V[0] |
| CVBR1 | RD | C4V[15] | C4V[14] | C4V[13] | C4V[12] | C4V[11] | C4V[10] | C4V[9] | C4V[8] |
| CVBR2 | RD | C5V[7] | C5V[6] | C5V[5] | C5V[4] | C5V[3] | C5V[2] | C5V[1] | C5V[0] |
| CVBR3 | RD | C5V[15] | C5V[14] | C5V[13] | C5V[12] | C5V[11] | C5V[10] | C5V[9] | C5V[8] |
| CVBR4 | RD | C6V[7] | C6V[6] | C6V[5] | C6V[4] | C6V[3] | C6V[2] | C6V[1] | C6V[0] |
| CVBR5 | RD | C6V[15] | C6V[14] | C6V[13] | C6V[12] | C6V[11] | C6V[10] | C6V[9] | C6V[8] |

### Table 42. Cell Voltage Register Group C
<!-- page: 64 -->

**Table 42. Cell Voltage Register Group C** ([table-48-p64-register.csv](ltc6813-1/tables/table-48-p64-register.csv), p. 64)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CVCR0 | RD | C7V[7] | C7V[6] | C7V[5] | C7V[4] | C7V[3] | C7V[2] | C7V[1] | C7V[0] |
| CVCR1 | RD | C7V[15] | C7V[14] | C7V[13] | C7V[12] | C7V[11] | C7V[10] | C7V[9] | C7V[8] |
| CVCR2* | RD | C8V[7]* | C8V[6]* | C8V[5]* | C8V[4]* | C8V[3]* | C8V[2]* | C8V[1]* | C8V[0]* |
| CVCR3* | RD | C8V[15]* | C8V[14]* | C8V[13]* | C8V[12]* | C8V[11]* | C8V[10]* | C8V[9]* | C8V[8]* |
| CVCR4 | RD | C9V[7] | C9V[6] | C9V[5] | C9V[4] | C9V[3] | C9V[2] | C9V[1] | C9V[0] |
| CVCR5 | RD | C9V[15] | C9V[14] | C9V[13] | C9V[12] | C9V[11] | C9V[10] | C9V[9] | C9V[8] |

- **\*:** After performing the ADOL command, CVCR2 and CVCR3 of Cell Voltage Register Group C will contain the result of measuring Cell 7 from ADC1.

### Table 43. Cell Voltage Register Group D
<!-- page: 64 -->

**Table 43. Cell Voltage Register Group D** ([table-49-p64-register.csv](ltc6813-1/tables/table-49-p64-register.csv), p. 64)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CVDR0 | RD | C10V[7] | C10V[6] | C10V[5] | C10V[4] | C10V[3] | C10V[2] | C10V[1] | C10V[0] |
| CVDR1 | RD | C10V[15] | C10V[14] | C10V[13] | C10V[12] | C10V[11] | C10V[10] | C10V[9] | C10V[8] |
| CVDR2 | RD | C11V[7] | C11V[6] | C11V[5] | C11V[4] | C11V[3] | C11V[2] | C11V[1] | C11V[0] |
| CVDR3 | RD | C11V[15] | C11V[14] | C11V[13] | C11V[12] | C11V[11] | C11V[10] | C11V[9] | C11V[8] |
| CVDR4 | RD | C12V[7] | C12V[6] | C12V[5] | C12V[4] | C12V[3] | C12V[2] | C12V[1] | C12V[0] |
| CVDR5 | RD | C12V[15] | C12V[14] | C12V[13] | C12V[12] | C12V[11] | C12V[10] | C12V[9] | C12V[8] |

### Table 44. Cell Voltage Register Group E
<!-- page: 64 -->

**Table 44. Cell Voltage Register Group E** ([table-50-p64-register.csv](ltc6813-1/tables/table-50-p64-register.csv), p. 64)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CVER0 | RD | C13V[7] | C13V[6] | C13V[5] | C13V[4] | C13V[3] | C13V[2] | C13V[1] | C13V[0] |
| CVER1 | RD | C13V[15] | C13V[14] | C13V[13] | C13V[12] | C13V[11] | C13V[10] | C13V[9] | C13V[8] |
| CVER2* | RD | C14V[7]* | C14V[6]* | C14V[5]* | C14V[4]* | C14V[3]* | C14V[2]* | C14V[1]* | C14V[0]* |
| CVER3* | RD | C14V[15]* | C14V[14]* | C14V[13]* | C14V[12]* | C14V[11]* | C14V[10]* | C14V[9]* | C14V[8]* |
| CVER4 | RD | C15V[7] | C15V[6] | C15V[5] | C15V[4] | C15V[3] | C15V[2] | C15V[1] | C15V[0] |
| CVER5 | RD | C15V[15] | C15V[14] | C15V[13] | C15V[12] | C15V[11] | C15V[10] | C15V[9] | C15V[8] |

- **\*:** After performing the ADOL command, CVER2 and CVER3 of Cell Voltage Register Group E will contain the result of measuring Cell 13 from ADC2.

### Table 45. Cell Voltage Register Group F
<!-- page: 64 -->

**Table 45. Cell Voltage Register Group F** ([table-51-p64-register.csv](ltc6813-1/tables/table-51-p64-register.csv), p. 64)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| CVFR0 | RD | C16V[7] | C16V[6] | C16V[5] | C16V[4] | C16V[3] | C16V[2] | C16V[1] | C16V[0] |
| CVFR1 | RD | C16V[15] | C16V[14] | C16V[13] | C16V[12] | C16V[11] | C16V[10] | C16V[9] | C16V[8] |
| CVFR2 | RD | C17V[7] | C17V[6] | C17V[5] | C17V[4] | C17V[3] | C17V[2] | C17V[1] | C17V[0] |
| CVFR3 | RD | C17V[15] | C17V[14] | C17V[13] | C17V[12] | C17V[11] | C17V[10] | C17V[9] | C17V[8] |
| CVFR4 | RD | C18V[7] | C18V[6] | C18V[5] | C18V[4] | C18V[3] | C18V[2] | C18V[1] | C18V[0] |
| CVFR5 | RD | C18V[15] | C18V[14] | C18V[13] | C18V[12] | C18V[11] | C18V[10] | C18V[9] | C18V[8] |

### Table 46. Auxiliary Register Group A
<!-- page: 65 -->

**Table 46. Auxiliary Register Group A** ([table-52-p65-register.csv](ltc6813-1/tables/table-52-p65-register.csv), p. 65)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| AVAR0 | RD | G1V[7] | G1V[6] | G1V[5] | G1V[4] | G1V[3] | G1V[2] | G1V[1] | G1V[0] |
| AVAR1 | RD | G1V[15] | G1V[14] | G1V[13] | G1V[12] | G1V[11] | G1V[10] | G1V[9] | G1V[8] |
| AVAR2 | RD | G2V[7] | G2V[6] | G2V[5] | G2V[4] | G2V[3] | G2V[2] | G2V[1] | G2V[0] |
| AVAR3 | RD | G2V[15] | G2V[14] | G2V[13] | G2V[12] | G2V[11] | G2V[10] | G2V[9] | G2V[8] |
| AVAR4 | RD | G3V[7] | G3V[6] | G3V[5] | G3V[4] | G3V[3] | G3V[2] | G3V[1] | G3V[0] |
| AVAR5 | RD | G3V[15] | G3V[14] | G3V[13] | G3V[12] | G3V[11] | G3V[10] | G3V[9] | G3V[8] |

**Table 47. Auxiliary Register Group B** ([table-53-p65-register.csv](ltc6813-1/tables/table-53-p65-register.csv), p. 65)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| AVBR0 | RD | G4V[7] | G4V[6] | G4V[5] | G4V[4] | G4V[3] | G4V[2] | G4V[1] | G4V[0] |
| AVBR1 | RD | G4V[15] | G4V[14] | G4V[13] | G4V[12] | G4V[11] | G4V[10] | G4V[9] | G4V[8] |
| AVBR2 | RD | G5V[7] | G5V[6] | G5V[5] | G5V[4] | G5V[3] | G5V[2] | G5V[1] | G5V[0] |
| AVBR3 | RD | G5V[15] | G5V[14] | G5V[13] | G5V[12] | G5V[11] | G5V[10] | G5V[9] | G5V[8] |
| AVBR4 | RD | REF[7] | REF[6] | REF[5] | REF[4] | REF[3] | REF[2] | REF[1] | REF[0] |
| AVBR5 | RD | REF[15] | REF[14] | REF[13] | REF[12] | REF[11] | REF[10] | REF[9] | REF[8] |

**Table 48. Auxiliary Register Group C** ([table-54-p65-register.csv](ltc6813-1/tables/table-54-p65-register.csv), p. 65)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| AVCR0 | RD | G6V[7] | G6V[6] | G6V[5] | G6V[4] | G6V[3] | G6V[2] | G6V[1] | G6V[0] |
| AVCR1 | RD | G6V[15] | G6V[14] | G6V[13] | G6V[12] | G6V[11] | G6V[10] | G6V[9] | G6V[8] |
| AVCR2 | RD | G7V[7] | G7V[6] | G7V[5] | G7V[4] | G7V[3] | G7V[2] | G7V[1] | G7V[0] |
| AVCR3 | RD | G7V[15] | G7V[14] | G7V[13] | G7V[12] | G7V[11] | G7V[10] | G7V[9] | G7V[8] |
| AVCR4 | RD | G8V[7] | G8V[6] | G8V[5] | G8V[4] | G8V[3] | G8V[2] | G8V[1] | G8V[0] |
| AVCR5 | RD | G8V[15] | G8V[14] | G8V[13] | G8V[12] | G8V[11] | G8V[10] | G8V[9] | G8V[8] |

**Table 49. Auxiliary Register Group D** ([table-55-p65-register.csv](ltc6813-1/tables/table-55-p65-register.csv), p. 65)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| AVDR0 | RD | G9V[7] | G9V[6] | G9V[5] | G9V[4] | G9V[3] | G9V[2] | G9V[1] | G9V[0] |
| AVDR1 | RD | G9V[15] | G9V[14] | G9V[13] | G9V[12] | G9V[11] | G9V[10] | G9V[9] | G9V[8] |
| AVDR2 | RD | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 |
| AVDR3 | RD | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 | RSVD1 |
| AVDR4 | RD | C16OV | C16UV | C15OV | C15UV | C14OV | C14UV | C13OV | C13UV |
| AVDR5 | RD | RSVD1 | RSVD1 | RSVD1 | RSVD1 | C18OV | C18UV | C17OV | C17UV |

### Table 50. Status Register Group A
<!-- page: 66 -->

**Table 50. Status Register Group A** ([table-56-p66-register.csv](ltc6813-1/tables/table-56-p66-register.csv), p. 66)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| STAR0 | RD | SC[7] | SC[6] | SC[5] | SC[4] | SC[3] | SC[2] | SC[1] | SC[0] |
| STAR1 | RD | SC[15] | SC[14] | SC[13] | SC[12] | SC[11] | SC[10] | SC[9] | SC[8] |
| STAR2 | RD | ITMP[7] | ITMP[6] | ITMP[5] | ITMP[4] | ITMP[3] | ITMP[2] | ITMP[1] | ITMP[0] |
| STAR3 | RD | ITMP[15] | ITMP[14] | ITMP[13] | ITMP[12] | ITMP[11] | ITMP[10] | ITMP[9] | ITMP[8] |
| STAR4 | RD | VA[7] | VA[6] | VA[5] | VA[4] | VA[3] | VA[2] | VA[1] | VA[0] |
| STAR5 | RD | VA[15] | VA[14] | VA[13] | VA[12] | VA[11] | VA[10] | VA[9] | VA[8] |

### Table 51. Status Register Group B
<!-- page: 66 -->

**Table 51. Status Register Group B** ([table-57-p66-register.csv](ltc6813-1/tables/table-57-p66-register.csv), p. 66)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| STBR0 | RD | VD[7] | VD[6] | VD[5] | VD[4] | VD[3] | VD[2] | VD[1] | VD[0] |
| STBR1 | RD | VD[15] | VD[14] | VD[13] | VD[12] | VD[11] | VD[10] | VD[9] | VD[8] |
| STBR2 | RD | C4OV | C4UV | C3OV | C3UV | C2OV | C2UV | C1OV | C1UV |
| STBR3 | RD | C8OV | C8UV | C7OV | C7UV | C6OV | C6UV | C5OV | C5UV |
| STBR4 | RD | C12OV | C12UV | C11OV | C11UV | C10OV | C10UV | C9OV | C9UV |
| STBR5 | RD | REV[3] | REV[2] | REV[1] | REV[0] | RSVD | RSVD | MUXFAIL | THSD |

### Table 52. COMM Register Group
<!-- page: 66 -->

**Table 52. COMM Register Group** ([table-58-p66-register.csv](ltc6813-1/tables/table-58-p66-register.csv), p. 66)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| COMM0 | RD/WR | ICOM0[3] | ICOM0[2] | ICOM0[1] | ICOM0[0] | D0[7] | D0[6] | D0[5] | D0[4] |
| COMM1 | RD/WR | D0[3] | D0[2] | D0[1] | D0[0] | FCOM0[3] | FCOM0[2] | FCOM0[1] | FCOM0[0] |
| COMM2 | RD/WR | ICOM1[3] | ICOM1[2] | ICOM1[1] | ICOM1[0] | D1[7] | D1[6] | D1[5] | D1[4] |
| COMM3 | RD/WR | D1[3] | D1[2] | D1[1] | D1[0] | FCOM1[3] | FCOM1[2] | FCOM1[1] | FCOM1[0] |
| COMM4 | RD/WR | ICOM2[3] | ICOM2[2] | ICOM2[1] | ICOM2[0] | D2[7] | D2[6] | D2[5] | D2[4] |
| COMM5 | RD/WR | D2[3] | D2[2] | D2[1] | D2[0] | FCOM2[3] | FCOM2[2] | FCOM2[1] | FCOM2[0] |

### Table 53. S Control Register Group
<!-- page: 66 -->

**Table 53. S Control Register Group** ([table-59-p66-register.csv](ltc6813-1/tables/table-59-p66-register.csv), p. 66)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| SCTRL0 | RD/WR | SCTL2[3] | SCTL2[2] | SCTL2[1] | SCTL2[0] | SCTL1[3] | SCTL1[2] | SCTL1[1] | SCTL1[0] |
| SCTRL1 | RD/WR | SCTL4[3] | SCTL4[2] | SCTL4[1] | SCTL4[0] | SCTL3[3] | SCTL3[2] | SCTL3[1] | SCTL3[0] |
| SCTRL2 | RD/WR | SCTL6[3] | SCTL6[2] | SCTL6[1] | SCTL6[0] | SCTL5[3] | SCTL5[2] | SCTL5[1] | SCTL5[0] |
| SCTRL3 | RD/WR | SCTL8[3] | SCTL8[2] | SCTL8[1] | SCTL8[0] | SCTL7[3] | SCTL7[2] | SCTL7[1] | SCTL7[0] |
| SCTRL4 | RD/WR | SCTL10[3] | SCTL10[2] | SCTL10[1] | SCTL10[0] | SCTL9[3] | SCTL9[2] | SCTL9[1] | SCTL9[0] |
| SCTRL5 | RD/WR | SCTL12[3] | SCTL12[2] | SCTL12[1] | SCTL12[0] | SCTL11[3] | SCTL11[2] | SCTL11[1] | SCTL11[0] |

### Table 54. PWM Register Group
<!-- page: 67 -->

**Table 54. PWM Register Group** ([table-60-p67-register.csv](ltc6813-1/tables/table-60-p67-register.csv), p. 67)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| PWMR0 | RD/WR | PWM2[3] | PWM2[2] | PWM2[1] | PWM2[0] | PWM1[3] | PWM1[2] | PWM1[1] | PWM1[0] |
| PWMR1 | RD/WR | PWM4[3] | PWM4[2] | PWM4[1] | PWM4[0] | PWM3[3] | PWM3[2] | PWM3[1] | PWM3[0] |
| PWMR2 | RD/WR | PWM6[3] | PWM6[2] | PWM6[1] | PWM6[0] | PWM5[3] | PWM5[2] | PWM5[1] | PWM5[0] |
| PWMR3 | RD/WR | PWM8[3] | PWM8[2] | PWM8[1] | PWM8[0] | PWM7[3] | PWM7[2] | PWM7[1] | PWM7[0] |
| PWMR4 | RD/WR | PWM10[3] | PWM10[2] | PWM10[1] | PWM10[0] | PWM9[3] | PWM9[2] | PWM9[1] | PWM9[0] |
| PWMR5 | RD/WR | PWM12[3] | PWM12[2] | PWM12[1] | PWM12[0] | PWM11[3] | PWM11[2] | PWM11[1] | PWM11[0] |

### Table 55. PWM/S Control Register Group B
<!-- page: 67 -->

**Table 55. PWM/S Control Register Group B** ([table-61-p67-register.csv](ltc6813-1/tables/table-61-p67-register.csv), p. 67)

| REGISTER | RD/WR | BIT 7 | BIT 6 | BIT 5 | BIT 4 | BIT 3 | BIT 2 | BIT 1 | BIT 0 |
|---|---|---|---|---|---|---|---|---|---|
| PSR0 | RD/WR | PWM14[3] | PWM14[2] | PWM14[1] | PWM14[0] | PWM13[3] | PWM13[2] | PWM13[1] | PWM13[0] |
| PSR1 | RD/WR | PWM16[3] | PWM16[2] | PWM16[1] | PWM16[0] | PWM15[3] | PWM15[2] | PWM15[1] | PWM15[0] |
| PSR2 | RD/WR | PWM18[3] | PWM18[2] | PWM18[1] | PWM18[0] | PWM17[3] | PWM17[2] | PWM7[1] | PWM17[0] |
| PSR3 | RD/WR | SCTL14[3] | SCTL14[2] | SCTL14[1] | SCTL14[0] | SCTL13[3] | SCTL13[2] | SCTL13[1] | SCTL13[0] |
| PSR4 | RD/WR | SCTL16[3] | SCTL16[2] | SCTL16[1] | SCTL16[0] | SCTL15[3] | SCTL15[2] | SCTL15[1] | SCTL15[0] |
| PSR5 | RD/WR | SCTL18[3] | SCTL18[2] | SCTL18[1] | SCTL18[0] | SCTL17[3] | SCTL17[2] | SCTL17[1] | SCTL17[0] |

### Table 56. Memory Bit Descriptions
<!-- page: 68 -->

**Table 56. Memory Bit Descriptions** ([table-62-p68-register.csv](ltc6813-1/tables/table-62-p68-register.csv), p. 68)

| NAME | DESCRIPTION | VALUES |
|---|---|---|
| GPIOx | GPIOx Pin Control | Write: 0 → GPIOx Pin Pull-Down ON; 1 → GPIOx Pin Pull-Down OFF (Default) Read: 0 → GPIOx Pin at Logic 0; 1 → GPIOx Pin at Logic 1 |
| REFON | References Powered Up | 1 → References Remain Powered Up Until Watchdog Timeout 0 → References Shut Down After Conversions (Default) |
| DTEN | Discharge Timer Enable (READ ONLY) | 1 → Enables the Discharge Timer for Discharge Switches 0 → Disables Discharge Timer |
| ADCOPT | ADC Mode Option Bit | ADCOPT: 0 → Selects Modes 27kHz, 7kHz, 422Hz or 26Hz with MD[1:0] Bits in ADC Conversion Commands (Default) 1 → Selects Modes 14kHz, 3kHz, 1kHz or 2kHz with MD[1:0] Bits in ADC Conversion Commands |
| VUV | Undervoltage Comparison Voltage* | Comparison Voltage = (VUV + 1) • 16 • 100µV Default: VUV = 0x000 |
| VOV | Overvoltage Comparison Voltage* | Comparison Voltage = VOV • 16 • 100µV Default: VOV = 0x000 |
| DCC[x] | Discharge Cell x | x = 1 to 18: 1 → Turn ON Shorting Switch for Cell x 0 → Turn OFF Shorting Switch for Cell x (Default) x = 0: 1 → Turn ON GPIO9 Pull-Down 0 → Turn OFF GPIO9 Pull-Down (Default) |
| DCTO | Discharge Time Out Value | DCTO(Write): 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F Time (Min): Disabled, 0.5, 1, 2, 3, 4, 5, 10, 15, 20, 30, 40, 60, 75, 90, 120 DCTO (Read): 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F Time Left (Min): Disabled or Timeout, 0–0.5, 0.5–1, 1–2, 2–3, 3–4, 4–5, 5–10, 10–15, 15–20, 20–30, 30–40, 40–60, 60–75, 75–90, 90–120 |
| MUTE | Mute Status (READ ONLY) | 1 → Mute is Activated and Discharging is Disabled 0 → Mute is Deactivated |
| FDRF | Force Digital Redundancy Failure | 1 → Forces the Digital Redundancy Comparison for ADC Conversions to Fail 0 → Enables the Normal Redundancy Comparison |
| PS[1:0] | Digital Redundancy Path Selection | 11 → Redundancy is Applied Only to ADC3 Digital Path 10 → Redundancy is Applied Only to ADC2 Digital Path 01 → Redundancy is Applied Only to ADC1 Digital Path 00 → Redundancy is Applied Sequentially to ADC1, ADC2 and ADC3 Digital Paths During Cell Conversions and Applied to ADC1 During AUX and STATUS Conversions |
| DTMEN | Enable Discharge Timer Monitor | 1 → Enables the Discharge Timer Monitor Function if the DTEN Pin is Asserted 0 → Disables the Discharge Timer Monitor Function. The Normal Discharge Timer Function Will Be Enabled if the DTEN Pin is Asserted |
| CxV | Cell x Voltage* | x = 1 to 18 16-Bit ADC Measurement Value for Cell x Cell Voltage for Cell x = CxV • 100µV CxV is Reset to 0xFFFF on Power-Up and After Clear Command |
| GxV | GPIO x Voltage* | x = 1 to 9 16-Bit ADC Measurement Value for GPIOx Voltage for GPIOx = GxV • 100µV GxV is Reset to 0xFFFF on Power-Up and After Clear Command |
| REF | 2nd Reference Voltage* | 16-Bit ADC Measurement Value for 2nd Reference Voltage for 2nd Reference = REF • 100µV Normal Range is within 2.990V to 3.014V (2.992V to 3.012V for LTC6813I), Allowing for Variations of $V_{REF2}$ Voltage and ADC TME as Well as Additional Margin to Prevent a False Fault from Being Reported |
| SC | Sum of All Cells Measurement* | 16-Bit ADC Measurement Value of the Sum of All Cell Voltages Sum of All Cells Voltage = SC • 100µV • 30 |
| ITMP | Internal Die Temperature* | 16-Bit ADC Measurement Value of Internal Die Temperature Temperature Measurement Voltage = ITMP • 100µV/7.6mV/°C – 276°C |
| VA | Analog Power Supply Voltage* | 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to 5.5V for Normal Operation |
| VD | Digital Power Supply Voltage* | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V |
| CxOV | Cell x Over-voltage Flag | x = 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 → Cell x Not Flagged for Overvoltage Condition; 1 → Cell x Flagged |
| CxUV | Cell x Under-voltage Flag | x = 1 to 18 Cell Voltage Compared to VUV Comparison Voltage 0 → Cell x Not Flagged for Undervoltage Condition; 1 → Cell x Flagged |
| REV | Revision Code | Device Revision Code |
| RSVD | Reserved Bits | Read: Read Back Value Can Be 1 or 0 |
| RSVD0 | Reserved Bits | Read: Read Back Value is Always 0 |
| RSVD1 | Reserved Bits | Read: Read Back Value is Always 1 |
| MUXFAIL | Multiplexer Self Test Result | Read: 0 → Multiplexer Passed Self Test; 1 → Multiplexer Failed Self Test |
| THSD | Thermal Shutdown Status | Read: 0 → Thermal Shutdown Has Not Occurred; 1 → Thermal Shutdown Has Occurred THSD Bit Cleared to 0 on Read of Status Register Group B |
| SCTLx[x] | S Pin Control Bits | 0000 – Drive S Pin High (De-Asserted) 0001 – Send 1 High Pulse on S Pin 0010 – Send 2 High Pulses on S Pin 0011 – Send 3 High Pulses on S Pin 0100 – Send 4 High Pulses on S Pin 0101 – Send 5 High Pulses on S Pin 0110 – Send 6 High Pulses on S Pin 0111 – Send 7 High Pulses on S Pin 1XXX – Drive S Pin Low (Asserted) |
| PWMx[x] | PWM Discharge Control | 0000 – Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 – Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 – Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . . . 1110 – Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 – Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired |
| ICOMn | Initial Communication Control Bits | Write \| $I^{2}C$ \| 0110 \| 0001 \| 0000 \| 0111 Write \| $I^{2}C$ \| START \| STOP \| BLANK \| NO TRANSMIT Write \| SPI \| 1000 \| 1010 \| 1001 \| 1111 Write \| SPI \| CSB Low \| CSB Falling Edge \| CSB High \| NO TRANSMIT Read \| $I^{2}C$ \| 0110 \| 0001 \| 0000 \| 0111 Read \| $I^{2}C$ \| START from Master \| STOP from Master \| SDA Low Between Bytes \| SDA High Between Bytes Read \| SPI \| 0111 |
| Dn | $I^{2}C$/SPI Communication Data Byte | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device |
| FCOMn | Final Communication Control Bits | Write \| $I^{2}C$ \| 0000 \| 1000 \| 1001 Write \| $I^{2}C$ \| Master ACK \| Master NACK \| Master NACK + STOP Write \| SPI \| X000 \| 1001 Write \| SPI \| CSB Low \| CSB High Read \| $I^{2}C$ \| 0000 \| 0111 \| 1111 \| 0001 \| 1001 Read \| $I^{2}C$ \| ACK from Master \| ACK from Slave \| NACK from Slave \| ACK from Slave + STOP from Master \| NACK from Slave + STOP from Master Read \| SPI \| 1111 |

- **\*:** Voltage equations use the decimal value of registers, 0 to 4095 for 12 bits and 0 to 65535 for 16 bits.

| NAME        | DESCRIPTION                        | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           | VALUES                                                                                                                                                                                                                                                                                                                                                                                                                           |
|-------------|------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|
| VA          | Analog Power Supply                | Voltage* 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to                                                                                                                                                                                                                                   | Voltage* 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to                                                                                                                                                                                                                                   | Voltage* 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to                                                                                                                                                                                                                                   | Voltage* 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to                                                                                                                                                                                                                                   | Voltage* 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to                                                                                                                                                                                                                                   | Voltage* 16-Bit ADC Measurement Value of Analog Power Supply Voltage Analog Power Supply Voltage = VA • 100µV The Value of VA is Set by External Components and Should Be in the Range 4.5V to                                                                                                                                                                                                                                   | 5.5V for Normal                                                                                                                                                                                                                                                                                                                                                                                                                  | Operation                                                                                                                                                                                                                                                                                                                                                                                                                        |
| VD          | Digital Power Supply Voltage*      | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       | 16-Bit ADC Measurement Value of Digital Power Supply Voltage Digital Power Supply Voltage = VD • 100µV Normal Range is within 2.7V to 3.6V                                                                                                                                                                                                                                                                                       |
| CxOV        | Cell x Over- voltage Flag          | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     | 1 to 18 Cell Voltage Compared to VOV Comparison Voltage 0 Cell x Not Flagged for Overvoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                     |
| CxUV        | Cell x Under- voltage Flag         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         | 18 Cell Voltage Compared to VUV Comparison Voltage 0 Cell x Not Flagged for Undervoltage Condition; 1 Cell x Flagged                                                                                                                                                                                                                                                                                                         |
| REV         | Revision Code                      | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             | Device Revision Code                                                                                                                                                                                                                                                                                                                                                                                                             |
| RSVD        | Reserved Bits                      | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              | Read: Read Back Value Can Be 1 or 0                                                                                                                                                                                                                                                                                                                                                                                              |
|             | Reserved Bits                      | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 0                                                                                                                                                                                                                                                                                                                                                                                                |
| RSVD0 RSVD1 | Reserved Bits                      | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                | Read: Read Back Value is Always 1                                                                                                                                                                                                                                                                                                                                                                                                |
| MUXFAIL     | Multiplexer Self Test Result       | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         | Read: 0 Multiplexer Passed Self Test; 1 Multiplexer Failed Self Test                                                                                                                                                                                                                                                                                                                                                         |
| THSD        | Thermal Shutdown Status            | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               | Read: 0 Thermal Shutdown Has Not Occurred; 1 Thermal Shutdown Has Occurred Bit Cleared to 0 on Read of Status Register Group B                                                                                                                                                                                                                                                                                               |
| SCTLx[x]    | S Pin Control Bits                 | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            | THSD 0000 - Drive S Pin High (De-Asserted) 0001 - Send 1 High Pulse on S Pin 0010 - Send 2 High Pulses on S Pin 0011 - Send 3 High Pulses on S Pin 0100 - Send 4 High Pulses on S Pin 0101 - Send 5 High Pulses on S Pin 0110 - Send 6 High Pulses on S Pin 0111 - Send 7 High Pulses on S Pin 1XXX - Drive S Pin Low (Asserted) 0000                                                                                            |
| PWMx[x]     | PWM Discharge Control              | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired | - Selects 0% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0001 - Selects 6.7% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 0010 - Selects 13.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired . 1110 - Selects 93.3% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired 1111 - Selects 100% Discharge Duty Cycle if DCCx = 1 and Watchdog Timer Has Expired |
| ICOMn       | Initial Communication Control Bits |                                                                                                                                                                                                                                                                                                                                                                                                                                  | $I^{2}C$ | 0110                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  | 0000                                                                                                                                                                                                                                                                                                                                                                                                                             | 0111                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                                                                                                                                                                                                                                                                                                                                                                                  |
| ICOMn       | Initial Communication Control Bits |                                                                                                                                                                                                                                                                                                                                                                                                                                  | $I^{2}C$ | START                                                                                                                                                                                                                                                                                                                                                                                                                            | STOP BLANK NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                                           | STOP BLANK NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                                           | STOP BLANK NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                                           | STOP BLANK NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                                           | STOP BLANK NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                                           |
| ICOMn       | Initial Communication Control Bits |                                                                                                                                                                                                                                                                                                                                                                                                                                  | SPI                                                                                                                                                                                                                                                                                                                                                                                                                              | 1000                                                                                                                                                                                                                                                                                                                                                                                                                             | 1010 1001 1111                                                                                                                                                                                                                                                                                                                                                                                                                   | 1010 1001 1111                                                                                                                                                                                                                                                                                                                                                                                                                   | 1010 1001 1111                                                                                                                                                                                                                                                                                                                                                                                                                   | 1010 1001 1111                                                                                                                                                                                                                                                                                                                                                                                                                   | 1010 1001 1111                                                                                                                                                                                                                                                                                                                                                                                                                   |
| ICOMn       | Initial Communication Control Bits |                                                                                                                                                                                                                                                                                                                                                                                                                                  | $I^{2}C$ | CSB Low                                                                                                                                                                                                                                                                                                                                                                                                                          | CSB Falling Edge CSB High NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                            | CSB Falling Edge CSB High NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                            | CSB Falling Edge CSB High NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                            | CSB Falling Edge CSB High NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                            | CSB Falling Edge CSB High NO TRANSMIT                                                                                                                                                                                                                                                                                                                                                                                            |
| ICOMn       | Initial Communication Control Bits | Read                                                                                                                                                                                                                                                                                                                                                                                                                             | $I^{2}C$ | 0110                                                                                                                                                                                                                                                                                                                                                                                                                             | 0001 0000 0111                                                                                                                                                                                                                                                                                                                                                                                                                   | 0001 0000 0111                                                                                                                                                                                                                                                                                                                                                                                                                   | 0001 0000 0111                                                                                                                                                                                                                                                                                                                                                                                                                   | 0001 0000 0111                                                                                                                                                                                                                                                                                                                                                                                                                   | 0001 0000 0111                                                                                                                                                                                                                                                                                                                                                                                                                   |
| ICOMn       | Initial Communication Control Bits | Read                                                                                                                                                                                                                                                                                                                                                                                                                             | $I^{2}C$ | START from Master                                                                                                                                                                                                                                                                                                                                                                                                                | STOP from Master SDA Low Between Bytes SDA High Between Bytes                                                                                                                                                                                                                                                                                                                                                                    | STOP from Master SDA Low Between Bytes SDA High Between Bytes                                                                                                                                                                                                                                                                                                                                                                    | STOP from Master SDA Low Between Bytes SDA High Between Bytes                                                                                                                                                                                                                                                                                                                                                                    | STOP from Master SDA Low Between Bytes SDA High Between Bytes                                                                                                                                                                                                                                                                                                                                                                    | STOP from Master SDA Low Between Bytes SDA High Between Bytes                                                                                                                                                                                                                                                                                                                                                                    |
| ICOMn       | Initial Communication Control Bits | Read                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  | SPI 0111                                                                                                                                                                                                                                                                                                                                                                                                                         | SPI 0111                                                                                                                                                                                                                                                                                                                                                                                                                         | SPI 0111                                                                                                                                                                                                                                                                                                                                                                                                                         | SPI 0111                                                                                                                                                                                                                                                                                                                                                                                                                         | SPI 0111                                                                                                                                                                                                                                                                                                                                                                                                                         |
| Dn          | $I^{2}C$/SPI Communication Data Byte  | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     | Data Transmitted (Received) to (from) $I^{2}C$/SPI Slave Device                                                                                                                                                                                                                                                                                                                                                                     |
| FCOMn       | Final Communication Control Bits   | Write                                                                                                                                                                                                                                                                                                                                                                                                                            | $I^{2}C$ | 1000                                                                                                                                                                                                                                                                                                                                                                                                                             | 1000                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  | 1001                                                                                                                                                                                                                                                                                                                                                                                                                             | 1001                                                                                                                                                                                                                                                                                                                                                                                                                             |
| FCOMn       | Final Communication Control Bits   | Write                                                                                                                                                                                                                                                                                                                                                                                                                            | $I^{2}C$ | Master ACK                                                                                                                                                                                                                                                                                                                                                                                                                       | Master ACK                                                                                                                                                                                                                                                                                                                                                                                                                       | Master NACK                                                                                                                                                                                                                                                                                                                                                                                                                      | Master NACK                                                                                                                                                                                                                                                                                                                                                                                                                      | Master NACK + STOP                                                                                                                                                                                                                                                                                                                                                                                                               | Master NACK + STOP                                                                                                                                                                                                                                                                                                                                                                                                               |
| FCOMn       | Final Communication Control Bits   | Write                                                                                                                                                                                                                                                                                                                                                                                                                            | SPI                                                                                                                                                                                                                                                                                                                                                                                                                              | X000                                                                                                                                                                                                                                                                                                                                                                                                                             | X000                                                                                                                                                                                                                                                                                                                                                                                                                             | 1001                                                                                                                                                                                                                                                                                                                                                                                                                             | 1001                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  |
| FCOMn       | Final Communication Control Bits   | Write                                                                                                                                                                                                                                                                                                                                                                                                                            | SPI                                                                                                                                                                                                                                                                                                                                                                                                                              | CSB Low                                                                                                                                                                                                                                                                                                                                                                                                                          | CSB Low                                                                                                                                                                                                                                                                                                                                                                                                                          | CSB High                                                                                                                                                                                                                                                                                                                                                                                                                         | CSB High                                                                                                                                                                                                                                                                                                                                                                                                                         |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  |
| FCOMn       | Final Communication Control Bits   | Read                                                                                                                                                                                                                                                                                                                                                                                                                             | $I^{2}C$ | 0000                                                                                                                                                                                                                                                                                                                                                                                                                             | 0111 1111                                                                                                                                                                                                                                                                                                                                                                                                                        | 0111 1111                                                                                                                                                                                                                                                                                                                                                                                                                        |                                                                                                                                                                                                                                                                                                                                                                                                                                  | 0001                                                                                                                                                                                                                                                                                                                                                                                                                             | 1001                                                                                                                                                                                                                                                                                                                                                                                                                             |
| FCOMn       | Final Communication Control Bits   | Read                                                                                                                                                                                                                                                                                                                                                                                                                             | $I^{2}C$ | ACK from Master                                                                                                                                                                                                                                                                                                                                                                                                                  | ACK from Slave NACK                                                                                                                                                                                                                                                                                                                                                                                                              | ACK from Slave NACK                                                                                                                                                                                                                                                                                                                                                                                                              | from Slave                                                                                                                                                                                                                                                                                                                                                                                                                       | ACK from Slave + STOP from Master                                                                                                                                                                                                                                                                                                                                                                                                | NACK from Slave + STOP from Master                                                                                                                                                                                                                                                                                                                                                                                               |
| FCOMn       | Final Communication Control Bits   | Read                                                                                                                                                                                                                                                                                                                                                                                                                             | SPI                                                                                                                                                                                                                                                                                                                                                                                                                              | 1111                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  |                                                                                                                                                                                                                                                                                                                                                                                                                                  |

### APPLICATIONS INFORMATION
<!-- pages: 70-88 -->

### PROVIDING DC POWER
<!-- page: 70 -->

### Simple Linear Regulator
<!-- page: 70 -->

The  primary  supply  pin  for  the  LTC6813-1  is  the  5V (±0.5V) $V_{REG}$ input pin. To generate the required 5V supply for $V_{REG}$, the DRIVE pin can be used to form a discrete regulator with the addition of a few external components, as shown in Figure 32. The DRIVE pin provides a 5.7V output, capable of sourcing 1mA. When buffered with an NPN transistor , this provides a stable 5V over temperature. The NPN transistor should be chosen to have a sufficient Beta over temperature (> 40) to supply the necessary supply current. The peak $V_{REG}$ current requirement of the LTC6813-1 approaches 35mA when simultaneously communicating over isoSPI and making ADC conversions. If the $V_{REG}$ pin is required to support any additional load, a transistor with an even higher Beta may be required.

The NPN collector can be powered from any voltage source that is a minimum 6V above V . This includes the cells that are being monitored, or an unregulated power supply. A 100Ω/100nF RC decoupling network is recommended for the collector power connection to protect the NPN from transients. The emitter of the NPN should be bypassed with a 1µF capacitor . Larger capacitance should be avoided since this will increase the wake-up time of the LTC6813-1. Some attention should be given to the thermal characteristic of the NPN, as there can be significant heating with a high collector voltage.

### Improved Regulator Power Efficiency
<!-- page: 70 -->

For improved efficiency when powering the LTC6813-1 from the cell stack, $V_{REG}$ may be powered from a DC/DC converter , rather than the NPN pass transistor . An ideal circuit is based on Analog Devices LT8631 step-down regulator , as shown in Figure 33. A 100Ω resistor is recommended between the battery stack and the LT8631 input; this will prevent in-rush current when connecting to the stack and it will reduce conducted EMI. The EN/UVLO pin should be connected to the DRIVE pin, which will put the LT8631 into a low power state when the LTC6813-1 is in the SLEEP state.

![Figure 32. Simple V REG  Power Source Using NPN Pass Transistor](ltc6813-1/figures/ltc6813-1-f099.png)

*Figure 32. Simple $V_{REG}$ Power Source Using NPN Pass Transistor*

![Figure 33. V REG  Powered From Cell Stack with High Efficiency Regulator](ltc6813-1/figures/ltc6813-1-f100.png)

*Figure 33. $V_{REG}$ Powered From Cell Stack with High Efficiency Regulator*

### INTERNAL PROTECTION AND FILTERING
<!-- page: 71 -->

### Internal Protection Features
<!-- page: 71 -->

The LTC6813-1 incorporates various ESD safeguards to ensure robust performance. An equivalent circuit showing the specific protection structures is shown in Figure 34. Zener-like  suppressors  are  shown  with  their  nominal clamp voltage, and the unmarked diodes exhibit standard PN junction behavior .

### Filtering of Cell and GPIO Inputs
<!-- page: 71 -->

The LTC6813-1 uses a delta-sigma ADC, which includes a delta-sigma modulator followed by a SINC3 finite impulse response (FIR) digital filter . This greatly relaxes input filtering  requirements.  Furthermore,  the  programmable oversampling ratio allows the user to determine the best trade-off between measurement speed and filter cutoff frequency. Even with this high order low pass filter , fast transient noise can still induce some residual noise in measurements, especially in the faster conversion modes. This can be minimized by adding an RC low pass decoupling to each ADC input, which also helps reject potentially damaging high energy transients. Adding more than about 100Ω to the ADC inputs begins to introduce a systematic error in the measurement, which can be improved by raising the filter capacitance or mathematically compensating in software with a calibration procedure. For situations that demand the highest level of battery voltage ripple rejection, grounded capacitor filtering is recommended. This configuration has a series resistance and capacitors that decouple HF noise to V .  In systems where noise is less periodic or higher oversample rates are in use, a differential capacitor filter structure is adequate. In this configuration there are series resistors to each input, but the capacitors connect between the adjacent C pins. However, the differential capacitor sections interact. As a result, the filter response is less consistent and results in less attenuation than predicted by the RC, by approximately a decade. Note that the capacitors only see one cell of applied voltage (thus smaller and lower cost) and tend to distribute transient energy uniformly across the IC (reducing stress events on the internal protection structure). Figure 35 shows the two methods schematically. ADC accuracy varies with R, C as shown in the Typical Performance curves, but error is minimized if R = 100Ω and C = 10nF. The GPIO pins will always use a grounded capacitor configuration because the measurements are all with respect to $V^{-}$.

NOTE: ZENER VOLTAGE IS 8V UNLESS MARKED OTHERWISE.

![Figure 34. Internal ESD Protection Structures of the LTC6813-1](ltc6813-1/figures/ltc6813-1-f101.png)

*Figure 34. Internal ESD Protection Structures of the LTC6813-1*

![Figure 35. Input Filter Structure Configurations](ltc6813-1/figures/ltc6813-1-f102.png)

*Figure 35. Input Filter Structure Configurations*

### Using Nonstandard Cell Input Filters
<!-- page: 73 -->

A cell pin filter of 100Ω and 10nF is recommended for all applications. This filter provides the best combination of noise rejection and Total Measurement Error (TME) performance. In applications that use C pin RC filters larger than 100Ω/10nF there may be additional measurement error . Figure 36a shows how both total TME and TME variation increase as the RC time constant increases. The increased error is related to the MUX settling. It is possible to reduce TME levels to near data sheet specifications by implementing an extra single channel conversion before issuing a standard all channel ADCV command. Figure 37a shows the standard ADCV command sequence. Figure 37b andFigure 37c show the recommended command sequence and timing that will allow the MUX to settle. The purpose of the modified procedure is to allow the MUX to settle at C1/C7/C13 before the start of the measurement cycle. The delay between the C1/C7/C13 ADCV command and the All Channel ADCV command is dependent on the time constant of the RC being used. The general guidance is to wait 6 τ between the C1/C7/C13 ADCV command and the All Channel ADCV command. Figure 36b shows the expected TME when using the recommended command sequence.

![Figure 36. Cell Measurement TME](ltc6813-1/figures/ltc6813-1-f103.png)

*Figure 36 (a). Cell Measurement TME vs Input RC Values*

Digitized data: [cell-measurement-tme.csv](ltc6813-1/curves/cell-measurement-tme.csv) (x: Ω; y: mV) — values read off the printed plot by the digitizer, not published data.

![(b) Cell Measurement Error vs Input RC Values (Extra Conversion and Delay Before Measurement)](ltc6813-1/figures/ltc6813-1-f104.png)

*Figure 36 (b) Cell Measurement Error vs Input RC Values (Extra Conversion and Delay Before Measurement)*

![Figure 37. ADC Command Order](ltc6813-1/figures/ltc6813-1-f105.png)

*Figure 37. ADC Command Order*

### CELL BALANCING
<!-- page: 74 -->

### Cell Balancing with Internal MOSFETs
<!-- page: 74 -->

With  passive  balancing,  if  one  cell  in  a  series  stack becomes overcharged, an S output can slowly discharge this cell by connecting it to a resistor . Each S output is connected to an internal N-channel MOSFET with a maximum on resistance of 10Ω. An external resistor should be connected in series with these MOSFETs to allow most of the heat to be dissipated outside of the LTC6813-1 package, as illustrated in Figure 38a.

The internal discharge switches (MOSFETs) S1 through S18 can be used to passively balance cells as shown in Figure 38a with balancing current of 200mA or less (80mA or less if the die temperature is over 95°C). Balancing current larger than 200mA is not recommended for the internal switches due to excessive die heating. When discharging cells with the internal discharge switches, the die temperature should be monitored. See the Thermal Shutdown section.

Note that the anti-aliasing filter resistor is part of the discharge path, so it should be removed or reduced. Use of an RC for added cell voltage measurement filtering is OK but the filter resistor must remain small, typically around 10Ω to reduce the effect on the balance current.

![Figure 38. Internal/External Discharge Circuits](ltc6813-1/figures/ltc6813-1-f106.png)

*Figure 38. Internal/External Discharge Circuits*

### Cell Balancing with External T ransistors
<!-- page: 74 -->

For applications that require balancing currents above 200mA or large cell filters, the S outputs can be used to control external transistors. The LTC6813-1 includes an internal pull-up PMOS transistor with a 1k series resistor .  The  S  pins  can  act  as  digital  outputs  suitable  for driving the gate of an external MOSFET as illustrated in Figure 38b. Figure 35 shows external MOSFET circuits that include RC filtering. For applications with very low cell voltages the PMOS in Figure 38b can be replaced with a PNP . When a PNP is used, the resistor in series with the base should be reduced.

### Choosing a Discharge Resistor
<!-- page: 74 -->

When sizing the balancing resistor , it is important to know the typical battery imbalance and the allowable time for cell balancing. In most small battery applications, it is reasonable for the balancing circuitry to be able to correct for a 5% SOC (State of Charge) error with 5 hours of balancing. For example a 5AHr battery with a 5% SOC imbalance will have approximately 250mA Hrs of imbalance. Using a 50mA balancing current this could be corrected in 5 hours. With a 100mA balancing current, the error would be corrected in 2.5 hours. In systems with very large batteries, it becomes difficult to use passive balancing to correct large SOC imbalances in short periods of time. The excessive heat created during balancing generally limits the balancing current. In large capacity battery applications, if short balancing times are required, an active balancing solution should be considered. When choosing a balance resistor , the following equations can be used to help determine a resistor value:

![other (p. 74)](ltc6813-1/figures/ltc6813-1-f107.png)

### Active Cell Balancing
<!-- page: 75 -->

![Figure 39. 18-Cell Battery Stack Module with Active Balancing](ltc6813-1/figures/ltc6813-1-f108.png)

*Figure 39. 18-Cell Battery Stack Module with Active Balancing*

Applications that require 1A or greater of cell balancing current should consider implementing an active balancing  system.  Active  balancing  allows  for  much  higher balancing currents without the generation of excessive heat. Active balancing also allows for energy recovery since most of the balance current will be redistributed back to the battery pack. Figure 39 shows a simple active balancing implementation using Analog Devices LT8584. The LT8584 also has advanced features which can be controlled via the LTC6813-1. See S Pin Pulsing Using the S Pin Control Settings in this data sheet and the LT8584 data sheet for more details.

### DISCHARGE CONTROL DURING CELL MEASUREMENTS
<!-- page: 75 -->

If the discharge permitted (DCP) bit is high at the time of a cell measurement command, the S pin discharge states do not change during cell measurements. If the DCP bit is low, S pin discharge states will be disabled while the corresponding cell or adjacent cells are being measured. If using an external discharge transistor , the relatively low 1kΩ impedance of the internal LTC6813-1 PMOS transistors should allow the discharge currents to fully turn off before the cell measurement. Table 57 illustrates the ADCV command with DCP = 0. In this table, OFF indicates that the S pin discharge is forced off irrespective of the state of the corresponding DCC[x] bit. ON indicates that the S pin discharge will remain on during the measurement period if it was ON prior to the measurement command.

In some cases, it is not possible for the automatic discharge control to eliminate all measurement error caused by running the discharges. This is due to the discharge transistor not turning off fast enough for the cell voltage to completely settle before the measurement starts. For the best measurement accuracy when running discharge, the MUTE and UNMUTE commands should be used. The MUTE command can be issued to temporarily disable all discharge transistors before the ADCV command is issued. After the cell conversion completes, an UNMUTE can be sent to re-enable all discharge transistors that were previously ON. Using this method maximizes the measurement accuracy with a very small time penalty.

### Method to Verify Discharge Circuits
<!-- page: 75 -->

When using the internal discharge feature, the ability to verify discharge functionality can be implemented in software.  In  applications  using  an  external  discharge MOSFET, an additional resistor can be added between the battery cell and the source of the discharge MOSFET . This will allow the system to test discharge functionality.

**Table 57. Discharge Control During an ADCV Command with DCP = 0** ([table-63-p76-data.csv](ltc6813-1/tables/table-63-p76-data.csv), p. 76)

| PARAMETER | CELL 1/7/13 | CELL 2/8/14 | CELL 3/9/15 | CELL 4/10/16 | CELL 5/11/17  | CELL 6/12/18 | CELL 1/7/13 | CELL 2/8/14 | CELL 3/9/15 | CELL 4/10/16 | CELL 5/11/17 | CELL 6/12/18 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| **DISCHARGE PIN** | $t_{0}$ – $t_{1M}$ | $t_{1M}$ – $t_{2M}$ | $t_{2M}$ – $t_{3M}$ | $t_{3M}$ – $t_{4M}$ | $t_{4M}$ – $t_{5M}$ | $t_{5M}$ – $t_{6M}$ | $t_{6M}$ – $t_{1C}$ | $t_{1C}$ – $t_{2C}$ | $t_{2C}$ – $t_{3C}$ | $t_{3C}$ – $t_{4C}$ | $t_{4C}$ – $t_{5C}$ | $t_{5C}$ – $t_{6C}$ |
| S1 | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF |
| S2 | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON |
| S3 | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON |
| S4 | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON |
| S5 | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF |
| S6 | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF |
| S7 | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF |
| S8 | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON |
| S9 | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON |
| S10 | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON |
| S11 | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF |
| S12 | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF |
| S13 | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF |
| S14 | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON |
| S15 | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON |
| S16 | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF | ON |
| S17 | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF | OFF |
| S18 | OFF | ON | ON | ON | OFF | OFF | OFF | ON | ON | ON | OFF | OFF |

Both circuits are shown in Figure 40. The functionality of the discharge circuits can be verified by conducting cell measurements and comparing measurements when the discharge is off to measurements when the discharge is on. The measurement taken when the discharge is on requires that the discharge permit bit (DCP) be set. The change in the measurement when the discharge is turned on is calculable based on the resistor values. The following algorithm can be used in conjunction with Figure 40 to verify each discharge circuit:

1. Measure all cells with no discharging (all S outputs off) and read and store the results.
2. Turn on S1, S7 and S13.
3. Measure C1-C0, C7-C6, C13-C12.
4. Turn off S1, S7 and S13.
5. Turn on S2, S8 and S14.
6. Measure C2-C1, C8-C7, C14-C13.
7. Turn off S2, S8 and S14.

17. Turn on S6, S12 and S18.
18. Measure C6-C5, C12-C11, C18-C17.
19. Turn off S6, S12 and S18.
20. Read the Cell Voltage Register Groups to get the results of Steps 2 thru 19.
21. Compare new readings with old readings. Each cell voltage  reading  should  have  decreased  by  a  fixed percentage set by $R_{DISCHARGE}$ and $R_{FILTER}$ for internal designs and $R_{DISCHARGE1}$ and $R_{DISCHARGE2}$ for external  MOSFET  designs.  The  exact  amount  of decrease depends on the resistor values and MOSFET characteristics.

![other (p. 77)](ltc6813-1/figures/ltc6813-1-f109.png)

*Figure 40 Balancing Self Test Circuit (a) Internal Discharge Circuit*

![Figure 40. Balancing Self Test Circuit](ltc6813-1/figures/ltc6813-1-f110.png)

*Figure 40 Balancing Self Test Circuit (b) External Discharge Circuit*

### DIGITAL COMMUNICATIONS
<!-- page: 78 -->

### PEC Calculation
<!-- page: 78 -->

The Packet Error Code (PEC) can be used to ensure that the serial data read from the LTC6813-1 is valid and has not been corrupted. This is a critical feature for reliable communication,  particularly  in  environments  of  high noise. The LTC6813-1 requires that a PEC be calculated for all data being read from, and written to, the LTC6813-1. For this reason it is important to have an efficient method for calculating the PEC.

/************************************

Copyright 2012 Analog Devices, Inc. (ADI) Permission to freely use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies: THIS SOFTWARE IS PROVIDED 'AS IS' AND ADI DISCLAIMS ALL WARRANTIES INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL ADI BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM ANY USE OF SAME, INCLUDING ANY LOSS OF USE OR DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTUOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

***************************************/
```
int16 pec15Table[256];
int16 CRC15_POLY = 0x4599;
void init_PEC15_Table()
{
for (int i = 0; i < 256; i++)
{
remainder = i << 7;
for (int bit = 8; bit > 0; --bit)
{
if (remainder & 0x4000)
{
remainder = ((remainder << 1));
remainder = (remainder ^ CRC15_POLY)
}
else
{
remainder = ((remainder << 1));
}
}
pec15Table[i] = remainder&0xFFFF;
}
}
unsigned int16 pec15 (char *data , int len)
{
int16 remainder,address;
remainder = 16;//PEC seed
for (int i = 0; i < len; i++)
{
address = ((remainder >> 7) ^ data[i]) & 0xff;//calculate PEC table address
remainder = (remainder << 8 ) ^ pec15Table[address];
}
return (remainder*2);//The CRC15 has a 0 in the LSB so the final value must be multiplied by 2
}
```

***************************************/

The C code below provides a simple implementation of a lookup-table-derived PEC calculation method. There are two functions. The first function init\_PEC15\_Table() should only be called once when the microcontroller starts and will initialize a PEC15 table array called pec15Table[]. This table will be used in all future PEC calculations. The PEC15 table can also be hard coded into the microcontroller rather than running the init\_PEC15\_Table() function at startup. The pec15() function calculates the PEC and will return the correct 15-bit PEC for byte arrays of any given length.

### isoSPI IBIAS and ICMP Setup
<!-- page: 79 -->

The LTC6813-1 allows the isoSPI links of each application to be optimized for power consumption or for noise immunity. The power and noise immunity of an isoSPI system is determined by the programmed $I_{B}$ current, which controls the isoSPI signaling currents. Bias current $I_{B}$ can range from 100µA to 1mA. Internal circuitry scales up this bias current to create the isoSPI signal currents equal to be 20 · $I_{B}$. A low $I_{B}$ reduces the isoSPI power consumption in the READY and ACTIVE states, while a high $I_{B}$ increases the amplitude of the differential signal voltage $V_{A}$ across the matching termination resistor , $R_{M}$. The $I_{B}$ current is programmed by the sum of the $R_{B1}$ and $R_{B2}$ resistors connected between the 2V IBIAS pin and GND as shown in Figure 41. The receiver input threshold is set by the ICMP voltage that is programmed with the resistor divider created by the $R_{B1}$ and $R_{B2}$ resistors. The receiver threshold will be half of the voltage present on the ICMP pin.

The following guidelines should be used when setting the bias current (100µA to 1mA) $I_{B}$ and the receiver comparator threshold voltage $V_{ICMP}$/2:

$R_{M}$ = Transmission Line Characteristic Impedance $Z_{0}$

Signal Amplitude $V_{A}$ = (20 · $I_{B}$) · ($R_{M}$/2)

$V_{TCMP}$ (Receiver Comparator Threshold) = K · $V_{A}$

![Equation as printed (p. 79)](ltc6813-1/figures/ltc6813-1-eqx03.png)

$V_{ICMP}$ (voltage on ICMP pin) = 2 · $V_{TCMP}$

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

Select  $I_{B}$ and  K  (Signal  Amplitude  $V_{A}$ to  Receiver Comparator Threshold ratio) according to the application:

For lower power links: $I_{B}$ = 0.5mA and K = 0.5

For full power links: $I_{B}$ = 1mA and K = 0.5

For long links (>50m): $I_{B}$ = 1mA and K = 0.25

For applications with little system noise, setting $I_{B}$ to 0.5mA is a good compromise between power consumption and noise immunity. Using this $I_{B}$ setting with a 1:1 transformer and $R_{M}$ = 100Ω, $R_{B1}$ should be set to 3.01k and $R_{B2}$ set to 1k. With typical CAT5 twisted pair , these settings will allow for communication up to 50m. For applications in very noisy environments or that require cables longer than 50m it is recommended to increase $I_{B}$ to  1mA.  Higher  drive  current  compensates  for  the increased insertion loss in the cable and provides high noise immunity. When using cables over 50m and a transformer with a 1:1 turns ratio and $R_{M}$ = 100Ω, $R_{B1}$ would be 1.5k and $R_{B2}$ would be 499Ω.

The maximum clock rate of an isoSPI link is determined by the length of the isoSPI cable. For cables 10m or less, the maximum 1MHz SPI clock frequency is possible. As the length of the cable increases, the maximum possible SPI clock rate decreases. This dependence is a result of the increased propagation delays that can create possible timing violations. Figure 42 shows how the maximum data rate reduces as the cable length increases when using a CAT5 twisted pair .

Cable delay affects three timing specifications: $t_{CLK}$, $t_{6}$ and $t_{7}$. In the Electrical Characteristics table, each of these specifications is de-rated by 100ns to allow for 50ns of cable delay. For longer cables, the minimum timing parameters may be calculated as shown below:

![Equation as printed (p. 80)](ltc6813-1/figures/ltc6813-1-eqx04.png)

$t_{CLK}$, $t_{6}$ and $t_{7}$ > 0.9µs + 2 · $t_{CABLE}$ (0.2m per ns)

![Figure 41. isoSPI Circuit](ltc6813-1/figures/ltc6813-1-f112.png)

*Figure 41. isoSPI Circuit*

![Figure 42. Data Rate vs Cable Length](ltc6813-1/figures/ltc6813-1-f113.png)

*Figure 42. Data Rate vs Cable Length*

Digitized data: [data-rate-vs-cable-length.csv](ltc6813-1/curves/data-rate-vs-cable-length.csv) (x: METERS; y: Mbps) — values read off the printed plot by the digitizer, not published data.

### Implementing a Modular isoSPI Daisy Chain
<!-- page: 80 -->

The hardware design of a daisy-chain isoSPI bus is identical for each device in the network due to the daisy-chain point-to-point architecture. The simple design as shown in Figure 41 is functional, but inadequate for most designs. The termination resistor $R_{M}$ should be split and bypassed with a capacitor as shown in Figure 43. This change provides both a differential and a common mode termination, and as such, increases the system noise immunity.

The use of cables between battery modules, particularly in automotive applications, can lead to increased noise susceptibility in the communication lines. For high levels of electromagnetic interference (EMC), additional filtering is recommended. The circuit example in Figure 43 shows the use of common mode chokes (CMC) to add common mode noise rejection from transients on the battery lines. The use of a center tapped transformer will also provide additional noise performance. A bypass capacitor connected to the center tap creates a low impedance for common mode noise (Figure 43b). Since transformers without a center tap can be less expensive, they may be preferred. In this case, the addition of a split termination resistor and a bypass capacitor (Figure 43a) can enhance the isoSPI performance. Large center tap capacitors greater than 10nF should be avoided as they may prevent the isoSPI common mode voltage from settling. Common mode chokes similar to those used in Ethernet or CANbus applications are recommended. Specific examples are provided in Table 59.

An  important  daisy  chain  design  consideration  is  the number of devices in the isoSPI network. Both the number of devices in a daisy chain and the length of wire between devices  determines  the  serial  timing  and  affects  data latency and throughput.

For  a  daisy  chain,  it  is  necessary  to  extend  minimum required $t_{5}$, the time from a rising chip select to the next falling chip select (between commands), from 0.65µs to 2µs (see Figure 25).

This timing for $t_{5}$ is set by the MCU on the SPI interface of LTC6820 or the SPI interface of the bottom LTC6813-1 device if it is configured to operate in SPI mode. If necessary, LTC6813-1 will internally adjust the timing for $t_{6}$ and $t_{5}$ while transmitting on the Master isoSPI port such that $t_{6}$ (Master port) > $t_{6(GOV)}$ and $t_{5}$ (Master port) > $t_{5(GOV)}$. This satisfies the timing requirement for the Slave port of the next device.

If  the  $t_{5}$ requirement  of  2µs  is  satisfied  on  the  SPI  interface, there is no strict limitation on the maximum number of devices in the daisy chain.

However, it is important to note that the serial read back time,  and  the  increased  current  consumption,  might  dictate a practical limitation in the size of the network.

![Figure 43. Daisy Chain Interface Components](ltc6813-1/figures/ltc6813-1-f114.png)

*Figure 43. Daisy Chain Interface Components*

### Connecting Multiple LTC6813-1s on the Same PCB
<!-- page: 81 -->

When connecting multiple LTC6813-1 devices on the same PCB, only a single transformer is required between the LTC6813-1 isoSPI ports. The absence of the cable also reduces the noise levels on the communication lines and often only a split termination is required. Figure 44 shows an example application that has multiple LTC6813-1s on the same PCB, communicating to the bottom MCU through an LTC6820 isoSPI driver . If a transformer with a center tap is used, a capacitor can be added for better noise rejection. Additional noise filtering can be provided with discrete common mode chokes (not shown) placed to both sides of the single transformer .

On single board designs with low noise requirements, it is possible for a simplified capacitor-isolated coupling as shown in Figure 45 to replace the transformer .

In this circuit, the transformer is directly replaced by two 10nF capacitors. A common mode choke (CMC) provides noise rejection similar to application circuits usng transformers. The circuit is designed to use IBIAS/ICMP settings identical to the transformer circuit.

![Figure 44. Daisy Chain Interface Components on Single Board](ltc6813-1/figures/ltc6813-1-f116.png)

*Figure 44. Daisy Chain Interface Components on Single Board*

### Connecting an MCU to an LTC6813-1 with an isoSPI Data Link
<!-- page: 82 -->

The LTC6820 will convert standard 4-wire SPI into a 2-wire isoSPI link that can communicate directly with the LTC6813-1. An example is shown in Figure 46. The LTC6820 can be used in applications to provide isolation between the microcontroller and the stack of LTC6813-1s. The LTC6820 also enables system configurations that have the BMS controller at a remote location relative to the LTC6813-1 devices and the battery pack.

### Transformer Selection Guide
<!-- page: 82 -->

As shown in Figure 41, a transformer or pair of transformers isolates the isoSPI signals between two isoSPI ports. The isoSPI signals have programmable pulse amplitudes up to 1.6 $V_{P-P}$ and pulse widths of 50ns and 150ns. To be able to transmit these pulses with the necessary fidelity, the system requires that the transformers have primary inductances above 60µH and a 1:1 turns ratio. It is also necessary to use a transformer with less than 2.5µH of leakage inductance. In terms of pulse shape the primary inductance will mostly affect the pulse droop of the 50ns and 150ns pulses. If the primary inductance is too low, the pulse amplitude will begin to droop and decay over the pulse period. When the pulse droop is severe enough, the effective pulse width seen by the receiver will drop substantially, reducing noise margin. Some droop is acceptable as long as it is a relatively small percentage of the total pulse amplitude. The leakage inductance primarily affects the rise and fall times of the pulses. Slower rise and fall times will effectively reduce the pulse width. Pulse width is determined by the receiver as the time the signal is above the threshold set at the ICMP pin. Slow rise and fall times cut into the timing margins. Generally it is best to keep pulse edges as fast as possible. When evaluating transformers, it is also worth noting the parallel winding capacitance. While transformers have very good CMRR at low frequency, this rejection will degrade at higher frequencies, largely due to the winding to winding capacitance. When choosing a transformer, it is best to pick one with less parallel winding capacitance when possible.

![Figure 45. Capacitive Isolation Coupling for LTC6813-1s on the Same PCB](ltc6813-1/figures/ltc6813-1-f117.png)

*Figure 45. Capacitive Isolation Coupling for LTC6813-1s on the Same PCB*

When choosing a transformer, it is equally important to pick a part that has an adequate isolation rating for the application. The working voltage rating of a transformer is a key spec when selecting a part for an application. Interconnecting daisy-chain links between LTC6813-1 devices see <90V stress in typical applications; ordinary pulse and LAN type transformers will suffice. Connections to the LTC6820, in general, may need much higher working voltage ratings for good long-term reliability. Usually, matching the working voltage to the voltage of the entire battery stack is conservative. Unfortunately, transformer vendors will often only specify one-second HV testing, and this is not equal to the long-term ('permanent') rating of the part. For example, according to most safety standards a 1.5kV rated transformer is expected to handle 230V continuously, and a 3kV device is capable of 1100V long-term, though manufacturers may not always certify to those levels (refer to actual vendor data for specifics). Usually, the higher voltage transformers are called 'high-isolation' or 'reinforced insulation' types by the suppliers. Table 58 shows a list of transformers that have been evaluated in isoSPI links.

In most applications a common mode choke is also necessary for noise rejection. Table 59 includes a list of suitable CMCs if the CMC is not already integrated into the transformer being used.

![Figure 46. Interfacing an LTC6813-1 with a µC Using an LTC6820 for Isolated SPI Control](ltc6813-1/figures/ltc6813-1-f118.png)

*Figure 46. Interfacing an LTC6813-1 with a µC Using an LTC6820 for Isolated SPI Control*

### Table 58. Recommended Transformers
<!-- page: 84 -->

**Table 58. Recommended Transformers** ([table-64-p84-data.csv](ltc6813-1/tables/table-64-p84-data.csv), p. 84)

| SUPPLIER | PART NUMBER | TEMP RANGE | $V_{WORKING}$ | $V_{HIPOT}$/60S | CT | CMC | H | L | W (W/ LEADS) | PINS | AEC-Q200 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| **Recommended Dual Transformers** |  |  |  |  |  |  |  |  |  |  |  |
| Bourns | SM91501AL | –40°C to 125°C | 1000V | 4.3kVdc | ● | ● | 5.0mm | 15.0mm | 14.7mm | 12SMT | ● |
| Bourns | SM13105L (AS4562) | –40°C to 125°C | 1600V | 4.3kVrms | ● | ● | 5.0mm | 15.0mm | 27.9mm | 12SMT | – |
| Bourns | US4374 | –40°C to 125°C | 950V | 4.3kVdc | ● | ● | 4.9mm | 15.6mm | 24.0mm | 12SMT | ● |
| Jingweida | S12502BA | –40°C to 125°C | 1000V | 4.3kVdc | ● | ● | 5.0mm | 14.8mm | 14.8mm | 12SMT | ● |
| Halo | TG110–AE050N5LF | –40°C to 85/125°C | 60V (est) | 1.5kVrms | ● | ● | 6.4mm | 12.7mm | 9.5mm | 16SMT | ● |
| Sumida | CLP178–C20114 | –40°C to 125°C | 1000V (est) | 3.75kVrms | ● | ● | 9mm | 17.5mm | 15.1mm | 12SMT | – |
| Sumida | CLP0612–C20115 |  | 600Vrms | 3.75kVrms | ● | – | 5.7mm | 12.7mm | 9.4mm | 16SMT | – |
| Pulse | HM2100NL | –40°C to 105°C | 1000V | 4.3kVdc | – | ● | 3.5mm | 14.7mm | 15.0mm | 10SMT | ● |
| Pulse | HM2112ZNL | –40°C to 125°C | 1600V | 4.3kVdc | ● | ● | 3.5mm | 14.7mm | 15.5mm | 12SMT | ● |
| Pulse | HX1188FNL | –40°C to 85°C | 60V (est) | 1.5kVrms | ● | ● | 6.0mm | 12.7mm | 9.7mm | 16SMT | – |
| Pulse | HX0068ANL | –40°C to 85°C | 60V (est) | 1.5kVrms | ● | ● | 2.1mm | 12.7mm | 9.7mm | 16SMT | – |
| Wurth | 7490140110 | –40°C to 85°C | 250Vrms | 4kVrms | ● | ● | 10.9mm | 24.6mm | 17.0mm | 16SMT | – |
| Wurth | 7490140111 | 0°C to 70°C | 1000V (est) | 4.5kVrms | ● | – | 8.4mm | 17.1mm | 15.2mm | 12SMT | – |
| Wurth | 749014018 | 0°C to 70°C | 250Vrms | 4kVrms | ● | ● | 8.4mm | 17.1mm | 15.2mm | 12SMT | – |
| **Recommended Single Transformers** |  |  |  |  |  |  |  |  |  |  |  |
| Bourns | SM91502AL | –40°C to 125°C | 1000V | 4.3kVdc | ● | ● | 6.5mm | 8.5mm | 8.9mm | 6SMT | ● |
| Bourns | SM13102AL (US4195) | –40°C to 125°C | 800V | 4kVrms | ● | ● | 3.8mm | 11.6mm | 21.1mm | 6SMT | – |
| Halo | TD04–QXLTAW | –40°C to 85°C | 1000V (est) | 5kVrms | ● | – | 8.6mm | 8.9mm | 16.6mm | 6TH | – |
| Halo | TGR04–6506V6LF | –40°C to 125°C | 300V | 3kVrms | ● | – | 10mm | 9.5mm | 12.1mm | 6SMT | – |
| Halo | TGR04–A6506NA6NL | –40°C to 125°C | 300V | 3kVrms | ● | – | 9.4mm | 8.9mm | 12.1mm | 6SMT | ● |
| Halo | TDR04–A550ALLF | –40°C to 105°C | 1000V | 5kVrms | ● | – | 6.4mm | 8.9mm | 16.6mm | 6TH | ● |
| Jingweida | S06107BA | –40°C to 125°C | 1000V (est) | 4.3kVdc | ● | ● | 6.3mm | 7.6mm | 9.9mm | 6SMT | – |
| Pulse | HM2101NL | –40°C to 105°C | 1000V | 4.3kVdc | – | ● | 5.7mm | 7.6mm | 9.3mm | 6SMT | ● |
| Pulse | HM2113ZNL | –40°C to 125°C | 1600V | 4.3kVdc | ● | ● | 3.5mm | 9mm | 15.5mm | 6SMT | ● |
| Sumida | CEEH96BNP–LTC6804/11 | –40°C to 125°C | 600V | 2.5kVrms | – | – | 7mm | 9.2mm | 12.0mm | 4SMT | – |
| Sumida | CEP99NP–LTC6804 | –40°C to 125°C | 600V | 2.5kVrms | ● | – | 10mm | 9.2mm | 12.0mm | 8SMT | – |
| Sumida | ESMIT–4180/A | –40°C to 105°C | 250Vrms | 3kVrms | – | – | 3.5mm | 5.2mm | 9.1mm | 4SMT | ● |
| Sumida | ESMIT–4187 | –40°C to 105°C | >400Vrms (est) | 2.5kVrms | – | – | 3.5mm | 7.5mm | 12.8mm | 4SMT | ● |
| TDK | VMT40DR–201S2P4 | –40°C to 125°C | 600V (est) | 3.4kVdc | ● | – | 4.0mm | 8.5mm | 13.8mm | 6SMT | ● |
| TDK | ALT4532V–201–T001 | –40°C to 105°C | 80V | ~1kV | ● | – | 2.9mm | 3.2mm | 4.5mm | 6SMT | ● |
| TDK | VGT10/9EE–204S2P4 | –40°C to 125°C | 700V | 2.8kVrms | ● | – | 10.6mm | 10.4mm | 12.6mm | 8SMT | ● |
| Sunlord | ALTW0806C–C03 | –40°C to 125°C | 300V (est) | 3kVrms | ● | – | 8.8mm | 6.3mm | 8.9mm | 6SMT | ● |
| Wurth | 750340848 | –40°C to 105°C | 250V | 3kVrms | – | – | 2.2mm | 4.4mm | 9.1mm | 4SMT | – |
| XFMRS | XFBMC29–BA09 | –40°C to 85°C | 1600V (est) | 2.9kVrms | ● | ● | 5.0mm | 10.0mm | 19.5mm | 6SMT | ● |

**Table 59. Recommended Common Mode Chokes** ([table-65-p84-data.csv](ltc6813-1/tables/table-65-p84-data.csv), p. 84)

| MANUFACTURER | PART NUMBER |
|---|---|
| TDK | ACT45B-101-2P |
| Murata | DLW43SH101XK2 |

### isoSPI Layout Guidelines
<!-- page: 85 -->

Layout of the isoSPI signal lines also plays a significant role in maximizing the noise immunity of a data link. The following layout guidelines are recommended:

1. The transformer should be placed as close to the isoSPI cable connector as possible. The distance should be kept less than 2cm. The LTC6813-1 should be placed close to but at least 1cm to 2cm away from the transformer to help isolate the IC from magnetic field coupling.
2. A $V^{-}$ ground plane should not extend under the transformer , the isoSPI connector or in between the transformer and the connector .
3. The isoSPI signal traces should be as direct as possible while isolated from adjacent circuitry by ground metal or space. No traces should cross the isoSPI signal lines, unless separated by a ground plane on an inner layer .

### System Supply Current
<!-- page: 85 -->

The LTC6813-1 has various supply current specifications for the different states of operation. The average supply current depends on the control loop in the system. It is necessary to know which commands are being executed each control loop cycle, and the duration of the control loop cycle. From this information it is possible to determine the percentage of time the LTC6813-1 is in the MEASURE state versus the low power SLEEP state. The amount of isoSPI or SPI communication will also affect the average supply current.

### Calculating Serial Throughput
<!-- page: 85 -->

For any given LTC6813-1 the calculation to determine communication time is simple: it is the number of bits in the transmission multiplied by the SPI clock period Rev. B

**Table 60. Daisy Chain Serial Time Equations** ([table-66-p85-data.csv](ltc6813-1/tables/table-66-p85-data.csv), p. 85)

| COMMAND TYPE | CMD BYTES + CMD PEC | DATA BYTES + DATA PEC PER IC | TOTAL BITS | COMMUNICATION TIME |
|---|---|---|---|---|
| Read | 4 | 8 | (4 + (8 • #ICs)) • 8 | Total Bits • Clock Period |
| Write | 4 | 8 | (4 + (8 • #ICs)) • 8 | Total Bits • Clock Period |
| Operation | 4 | 0 | 4 • 8 = 32 | 32 • Clock Period |

being used. The control protocol of the LTC6813-1 is very uniform so almost all commands can be categorized as a write, read or an operation. Table 60 can be used to determine the number of bits in a given LTC6813-1 command.

### ENHANCED APPLICATIONS
<!-- page: 85 -->

### Using the LTC6813-1 with Fewer than 18 Cells
<!-- page: 85 -->

Cells can be connected in a conventional bottom (C1) to top (C18) sequence with all unused C inputs either shorted to the highest connected cell or left open. The unused S pins can simply be left unconnected.

Alternatively, to optimize measurement synchronization in applications with fewer than eighteen cells, the unused C pins may be equally distributed between the top of the third MUX (C18), the top of the second MUX (C12) and the top of the first MUX (C6). See Figure 47. If the number of cells being measured is not a multiple of three, the top MUX(es) should have fewer cells connected. The unused cell inputs should be tied to the other unused inputs on the same MUX and then connected to the battery stack through a 100Ω resistor . The unused inputs will result in a reading of 0.0V for those cells.

### Current Measurement with a Hall-Effect Sensor
<!-- page: 85 -->

The LTC6813-1 auxiliary ADC inputs (GPIO pins) may be used for any analog signal, including active sensors with 0V to 5V analog outputs. For battery current measurements, Hall-effect sensors provide an isolated, low power solution. Figure 48 shows schematically a typical Hall-effect sensor that produces two outputs that proportion to the $V_{CC}$ provided. The sensor in Figure 48 has two bidirectional outputs centered at half of $V_{CC}$. CH1 is a 0A to 50A low range and CH2 is a 0A to 200A high range. The sensor is powered from a 5V source and produces analog outputs that are connected to GPIO pins or inputs of the

MUX application shown in Figure 50. The use of GPIO1 and GPIO2 as the ADC inputs has the possibility of being digitized within the same conversion sequence as the cell inputs (using the ADCVAX command), thus synchronizing cell voltage and cell current measurements.

![Figure 47. Cell Connection Schemes for 16 and 14 Cells](ltc6813-1/figures/ltc6813-1-f119.png)

*Figure 47. Cell Connection Schemes for 16 and 14 Cells*

![Figure 48. Interfacing a Typical Hall-Effect Battery Current Sensor to Auxiliary ADC Inputs](ltc6813-1/figures/ltc6813-1-f120.png)

*Figure 48. Interfacing a Typical Hall-Effect Battery Current Sensor to Auxiliary ADC Inputs*

### READING EXTERNAL TEMPERATURE PROBES
<!-- page: 87 -->

Figure 49 shows the typical biasing circuit for a negative temperature coefficient (NTC) thermistor . The 10k at 25°C is the most popular sensor value and the $V_{REF2}$ output stage is designed to provide the current required to bias several of these probes. The biasing resistor is selected to correspond to the NTC value so the circuit will provide 1.5V at 25°C ($V_{REF2}$ is 3V nominal). The overall circuit response is approximately -1%/°C in the range of typical cell temperatures, as shown in the chart of Figure 49.

### Expanding the Number of Auxiliary Measurements
<!-- page: 87 -->

The LTC6813-1 has nine GPIO pins that can be used as ADC inputs. In applications that need to measure more than nine signals, a multiplexer (MUX) circuit can be implemented to expand the analog measurements to sixteen different signals (Figure 50). The GPIO1 ADC input is used for measurement and MUX control is provided by the $I^{2}C$ port on GPIO 4 and 5. The buffer amplifier was selected for fast settling and will increase the usable throughput rate.

![Figure 49. Typical Temperature Probe Circuit and Relative Output](ltc6813-1/figures/ltc6813-1-f122.png)

*Figure 49. Typical Temperature Probe Circuit and Relative Output*

![Figure 50. MUX Circuit Supports Sixteen Additional Analog Measurements](ltc6813-1/figures/ltc6813-1-f123.png)

*Figure 50. MUX Circuit Supports Sixteen Additional Analog Measurements*

### PACKAGE DESCRIPTION
<!-- pages: 88-90 -->

![other (p. 88)](ltc6813-1/figures/ltc6813-1-f124.png)

### Typical Application

![application circuit (p. 90)](ltc6813-1/figures/ltc6813-1-f126.png)

### RELATED PARTS
<!-- page: 90 -->

**Related Parts** ([table-68-p90-data.csv](ltc6813-1/tables/table-68-p90-data.csv), p. 90)

| PART NUMBER | DESCRIPTION | COMMENTS |
|---|---|---|
| LTC6810-1/ LTC6810-2 | 4th Generation 6-Cell Battery Stack Monitor and Balancing IC | Measures Cell Voltages for Up to 6 Series Battery Cells. Daisy-Chain Capability Allows Multiple Devices to Be Connected to Measure Many Battery Cells Simultaneously. The isoSPI Bus Can Operate Up to 1MHz and Can Be Operated Bidirectionally for Fault Conditions, Such As a Broken Wire or Connector. Includes Internal Passive Cell Balancing of up to 150mA. Each Cell Measurement Channel Includes Redundant Measurement Capability. |
| LTC6811-1/ LTC6811-2 | 4th Generation 12-Cell Battery Stack Monitor and Balancing IC | Measures Cell Voltages for Up to 12 Series Battery Cells. Daisy-Chain Capability Allows Multiple Devices to Be Connected to Measure Many Battery Cells Simultaneously Via the Built-In 1MHz, 2-Wire Isolated Communication (isoSPI). Includes Capability for Passive Cell Balancing. |
| LTC6812-1 | 4th Generation 15-Cell Battery Stack Monitor and Balancing IC | Measures Cell Voltages for Up to 15 Series Battery Cells. The isoSPI Daisy-Chain Capability Allows Multiple Devices to Be Connected to Measure Many Battery Cells Simultaneously. The isoSPI Bus Can Operate Up to 1MHz and Can Be Operated Bidirectionally for Fault Conditions, Such As a Broken Wire or Connector. Includes Internal Passive Cell Balancing Capability of Up to 200mA. |
| LTC6820 | isoSPI Isolated Communications Interface | Provides an Isolated Interface for SPI Communication Up to 100 Meters, Using a Twisted Pair. Companion to the LTC6806, LTC6810, LTC6811, LTC6812 and LTC6813. |
