---
type: Analog Component
title: "LT3042 — 20V, 200mA, Ultralow Noise, Ultrahigh PSRR RF Linear Regulator"
description: "20V, 200mA, Ultralow Noise, Ultrahigh PSRR RF Linear Regulator"
resource: "https://www.analog.com/en/products/lt3042.html"
tags: ["datasheet", "linear"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/lt3042.pdf"
    title: "LT3042 data sheet"
    author: "team:analog-devices"
    last_modified: "03/21"
tables:
  - file: "lt3042/tables/table-00-p2-abs_max.csv"
    title: "Absolute Maximum Ratings (Note 1)"
    page: 2
  - file: "lt3042/tables/table-01-p2-data.csv"
    title: "Order Information"
    page: 2
  - file: "lt3042/tables/table-03-p3-spec.csv"
    title: "Electrical Characteristics"
    page: 3
  - file: "lt3042/tables/table-04-p14-data.csv"
    title: "Table 1. 1% Resistor for Common Output Voltages"
    page: 14
  - file: "lt3042/tables/table-05-p20-data.csv"
    title: "Table 2. PC Board Trace Resistance"
    page: 20
  - file: "lt3042/tables/table-06-p21-data.csv"
    title: "Table 3. Measured Thermal Resistance for DFN Package"
    page: 21
  - file: "lt3042/tables/table-07-p21-data.csv"
    title: "Table 4. Measured Thermal Resistance for MSOP Package"
    page: 21
  - file: "lt3042/tables/table-08-p28-data.csv"
    title: "table-08-p28-data.csv"
    page: 28
  - file: "lt3042/tables/table-09-p31-data.csv"
    title: "Revision History"
    page: 31
  - file: "lt3042/tables/table-10-p32-data.csv"
    title: "Related Parts"
    page: 32
figures:
  - file: "lt3042/figures/lt3042-f001.png"
    caption: "Typical Application"
    type: "application_circuit"
    page: 1
  - file: "lt3042/figures/lt3042-f002.png"
    caption: "Power Supply Ripple Rejection (p. 1)"
    type: "characteristic_curve"
    page: 1
  - file: "lt3042/figures/lt3042-f003.png"
    caption: "Pin Configuration"
    type: "pinout"
    page: 2
  - file: "lt3042/figures/lt3042-f004.png"
    caption: "Pin Configuration"
    type: "pinout"
    page: 2
  - file: "lt3042/figures/lt3042-f005.png"
    caption: "SET Pin Current (p. 5)"
    type: "characteristic_curve"
    page: 5
  - file: "lt3042/figures/lt3042-f006.png"
    caption: "SET Pin Current (p. 5, g. 2)"
    type: "characteristic_curve"
    page: 5
  - file: "lt3042/figures/lt3042-f007.png"
    caption: "Offset Voltage (VOUT – VSET) (p. 5)"
    type: "characteristic_curve"
    page: 5
  - file: "lt3042/figures/lt3042-f008.png"
    caption: "Offset Voltage (p. 6, g. 4)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f009.png"
    caption: "SET Pin Current (3042 G05)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f010.png"
    caption: "SET Pin Current (3042 G07)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f011.png"
    caption: "Offset Voltage (VOUT – VSET)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f012.png"
    caption: "Quiescent Current (3042 G10)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f013.png"
    caption: "Offset Voltage (VOUT – VSET)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f014.png"
    caption: "Load Regulation"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f015.png"
    caption: "Quiescent Current in Shutdown"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f016.png"
    caption: "Quiescent Current (3042 G12)"
    type: "characteristic_curve"
    page: 6
  - file: "lt3042/figures/lt3042-f017.png"
    caption: "Quiescent Current (p. 7)"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f018.png"
    caption: "GND Pin Current (3042 G16)"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f019.png"
    caption: "Minimum Input Voltage"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f020.png"
    caption: "Typical Dropout Voltage"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f021.png"
    caption: "GND Pin Current (3042 G17)"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f022.png"
    caption: "EN/UV Turn-On Threshold"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f023.png"
    caption: "Dropout Voltage"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f024.png"
    caption: "GND Pin Current (3042 G18)"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f025.png"
    caption: "EN/UV Pin Hysteresis"
    type: "characteristic_curve"
    page: 7
  - file: "lt3042/figures/lt3042-f026.png"
    caption: "Enable Pin Input Current"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f027.png"
    caption: "Input Pin Current"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f028.png"
    caption: "Internal Current Limit (3042 G28)"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f029.png"
    caption: "Enable Pin Current"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f030.png"
    caption: "Internal Current Limit (3042 G26)"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f031.png"
    caption: "Programmable Current Limit (3042 G29)"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f032.png"
    caption: "Negative Enable Pin Current"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f033.png"
    caption: "Internal Current Limit (3042 G27)"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f034.png"
    caption: "Programmable Current Limit (3042 G30)"
    type: "characteristic_curve"
    page: 8
  - file: "lt3042/figures/lt3042-f035.png"
    caption: "ILIM Pin Current"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f036.png"
    caption: "PG Output Low Voltage"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f037.png"
    caption: "ISET During Start-Up with Fast Start-Up Enabled (3042 G37)"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f038.png"
    caption: "PGFB Rising Threshold"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f039.png"
    caption: "PG Pin Leakage Current"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f040.png"
    caption: "Output Overshoot Recovery Current Sink (3042 G38)"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f041.png"
    caption: "PGFB Hysteresis"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f042.png"
    caption: "ISET During Start-Up with Fast Start-Up Enabled (3042 G36)"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f043.png"
    caption: "Output Overshoot Recovery Current Sink (3042 G39)"
    type: "characteristic_curve"
    page: 9
  - file: "lt3042/figures/lt3042-f044.png"
    caption: "VOUT Forced Above VOUT(NOMINAL)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f045.png"
    caption: "Power Supply Ripple Rejection (3042 G43)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f046.png"
    caption: "Integrated RMS Output Noise (10Hz to 100kHz) (3042 G46)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f048.png"
    caption: "Power Supply Ripple Rejection (3042 G41)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f049.png"
    caption: "Power Supply Ripple Rejection as a Function of Error Amplifier Input Pair"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f050.png"
    caption: "Integrated RMS Output Noise (10Hz to 100kHz) (3042 G47)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f051.png"
    caption: "Power Supply Ripple Rejection (3042 G42)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f052.png"
    caption: "Power Supply Ripple Rejection (3042 G45)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f053.png"
    caption: "Integrated RMS Output Noise (10Hz to 100kHz) (3042 G48)"
    type: "characteristic_curve"
    page: 10
  - file: "lt3042/figures/lt3042-f054.png"
    caption: "Noise Spectral Density (3042 G49)"
    type: "other"
    page: 11
  - file: "lt3042/figures/lt3042-f055.png"
    caption: "Noise Spectral Density as a Function of Error Amplifier Input Pair"
    type: "other"
    page: 11
  - file: "lt3042/figures/lt3042-f056.png"
    caption: "Line Transient Response"
    type: "scope_capture"
    page: 11
  - file: "lt3042/figures/lt3042-f057.png"
    caption: "Noise Spectral Density (3042 G50)"
    type: "other"
    page: 11
  - file: "lt3042/figures/lt3042-f058.png"
    caption: "Output Noise: 10Hz to 100kHz"
    type: "scope_capture"
    page: 11
  - file: "lt3042/figures/lt3042-f059.png"
    caption: "Noise Spectral Density (3042 G51)"
    type: "other"
    page: 11
  - file: "lt3042/figures/lt3042-f060.png"
    caption: "Load Transient Response"
    type: "scope_capture"
    page: 11
  - file: "lt3042/figures/lt3042-f061.png"
    caption: "Start-Up Time with and without Fast Start-Up Circuitry for Large CSET"
    type: "other"
    page: 11
  - file: "lt3042/figures/lt3042-f062.png"
    caption: "Input Supply Ramp-Up and Ramp-Down"
    type: "scope_capture"
    page: 11
  - file: "lt3042/figures/lt3042-f063.png"
    caption: "Block Diagram"
    type: "block_diagram"
    page: 13
  - file: "lt3042/figures/lt3042-f064.png"
    caption: "Figure 1. Basic Adjustable Regulator"
    type: "application_circuit"
    page: 14
  - file: "lt3042/figures/lt3042-f065.png"
    caption: "Figure 2. Guard Ring Layout"
    type: "layout_drawing"
    page: 15
  - file: "lt3042/figures/lt3042-f066.png"
    caption: "Figure 3. C OUT  and C SET  Connections for Stability"
    type: "application_circuit"
    page: 15
  - file: "lt3042/figures/lt3042-f067.png"
    caption: "Figure 4. Ceramic Capacitor DC Bias Characteristics"
    type: "characteristic_curve"
    page: 16
  - file: "lt3042/figures/lt3042-f068.png"
    caption: "Figure 5. Ceramic Capacitor Temperature Characteristics"
    type: "characteristic_curve"
    page: 16
  - file: "lt3042/figures/lt3042-f069.png"
    caption: "Figure 6. Capacitor Voltage Coefficient for Different Case Sizes"
    type: "characteristic_curve"
    page: 16
  - file: "lt3042/figures/lt3042-f070.png"
    caption: "Figure 7. Parallel Devices"
    type: "application_circuit"
    page: 20
  - file: "lt3042/figures/lt3042-f072.png"
    caption: "Figure 8. Example DFN Layout"
    type: "layout_drawing"
    page: 20
  - file: "lt3042/figures/lt3042-f073.png"
    caption: "12VIN  to 3.3V OUT  with 0.8µV RMS  Integrated Noise"
    type: "application_circuit"
    page: 23
  - file: "lt3042/figures/lt3042-f074.png"
    caption: "PGFB Disabled without Reverse Input Protection"
    type: "application_circuit"
    page: 23
  - file: "lt3042/figures/lt3042-f075.png"
    caption: "PGFB Disabled with Reverse Input Protection"
    type: "application_circuit"
    page: 23
  - file: "lt3042/figures/lt3042-f076.png"
    caption: "Low Noise CC/CV Lab Power Supply"
    type: "application_circuit"
    page: 23
  - file: "lt3042/figures/lt3042-f078.png"
    caption: "Programming Undervoltage Lockout"
    type: "application_circuit"
    page: 24
  - file: "lt3042/figures/lt3042-f079.png"
    caption: "Ratiometric Tracking"
    type: "application_circuit"
    page: 24
  - file: "lt3042/figures/lt3042-f080.png"
    caption: "Ultralow 1/f Noise Reference Buffer"
    type: "application_circuit"
    page: 25
  - file: "lt3042/figures/lt3042-f081.png"
    caption: "Paralleling Multiple Devices Using ILIM (Current Monitor) to Cancel Ballast Resistor Drop"
    type: "application_circuit"
    page: 25
  - file: "lt3042/figures/lt3042-f083.png"
    caption: "Paralleling Multiple LT3042s for Higher Output Current"
    type: "application_circuit"
    page: 26
  - file: "lt3042/figures/lt3042-f085.png"
    caption: "Ultralow Noise Higher Current Regulator with External PNP"
    type: "application_circuit"
    page: 27
  - file: "lt3042/figures/lt3042-f086.png"
    caption: "Ultralow Noise Higher Current Regulator with External NPN"
    type: "application_circuit"
    page: 27
  - file: "lt3042/figures/lt3042-f087.png"
    caption: "Low Noise Wheatstone Bridge Power Supply"
    type: "application_circuit"
    page: 28
  - file: "lt3042/figures/lt3042-f088.png"
    caption: "DD Package 10-Lead Plastic DFN (3mm × 3mm)"
    type: "other"
    page: 29
  - file: "lt3042/figures/lt3042-f090.png"
    caption: "MSE Package 10-Lead Plastic MSOP, Exposed Die Pad"
    type: "other"
    page: 30
  - file: "lt3042/figures/lt3042-f091.png"
    caption: "Parallel Devices"
    type: "application_circuit"
    page: 32
  - file: "lt3042/figures/lt3042-eq01.png"
    caption: "Equation as printed (p. 18)"
    type: equation
    page: 18
  - file: "lt3042/figures/lt3042-eq02.png"
    caption: "Equation as printed (p. 19)"
    type: equation
    page: 19
  - file: "lt3042/figures/lt3042-eq03.png"
    caption: "Equation as printed (p. 19)"
    type: equation
    page: 19
  - file: "lt3042/figures/lt3042-eq04.png"
    caption: "Equation as printed (p. 19)"
    type: equation
    page: 19
  - file: "lt3042/figures/lt3042-eq05.png"
    caption: "Equation as printed (p. 21)"
    type: equation
    page: 21
  - file: "lt3042/figures/lt3042-eq07.png"
    caption: "Equation as printed (p. 21)"
    type: equation
    page: 21
  - file: "lt3042/figures/lt3042-eq08.png"
    caption: "Equation as printed (p. 22)"
    type: equation
    page: 22
curves:
  - file: "lt3042/curves/capacitor-voltage-coefficient-for-different-case-sizes.csv"
    caption: "Figure 6. Capacitor Voltage Coefficient for Different Case Sizes"
    figure: "lt3042/figures/lt3042-f069.png"
    page: 16
    x_unit: "V"
    y_unit: "%"
    conditions: "MURATA: X7R, 25V, 4.7µF CERAMIC"
  - file: "lt3042/curves/ceramic-capacitor-dc-bias-characteristics.csv"
    caption: "Figure 4. Ceramic Capacitor DC Bias Characteristics"
    figure: "lt3042/figures/lt3042-f067.png"
    page: 16
    x_unit: "V"
    y_unit: "%"
    conditions: "BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10µF"
  - file: "lt3042/curves/ceramic-capacitor-temperature-characteristics.csv"
    caption: "Figure 5. Ceramic Capacitor Temperature Characteristics"
    figure: "lt3042/figures/lt3042-f068.png"
    page: 16
    x_unit: "°C"
    y_unit: "%"
    conditions: "BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10µF"
  - file: "lt3042/curves/curve-006.csv"
    caption: "SET Pin Current (p. 5, g. 2)"
    figure: "lt3042/figures/lt3042-f006.png"
    page: 5
    x_unit: "µA"
    y_unit: ""
    conditions: "N = 4354"
  - file: "lt3042/curves/curve-008.csv"
    caption: "Offset Voltage (p. 6, g. 4)"
    figure: "lt3042/figures/lt3042-f008.png"
    page: 6
    x_unit: "mV"
    y_unit: ""
  - file: "lt3042/curves/curve-011.csv"
    caption: "curve-011.csv"
    figure: "lt3042/figures/lt3042-f011.png"
    page: 6
    x_unit: "V"
    y_unit: "V"
    conditions: "I_L = 1mA, V_IN = 20V"
  - file: "lt3042/curves/dropout-voltage.csv"
    caption: "Dropout Voltage"
    figure: "lt3042/figures/lt3042-f023.png"
    page: 7
    x_unit: "°C"
    y_unit: "mV"
    conditions: "R_SET = 33.2kΩ"
  - file: "lt3042/curves/en-uv-pin-hysteresis.csv"
    caption: "EN/UV Pin Hysteresis"
    figure: "lt3042/figures/lt3042-f025.png"
    page: 7
    x_unit: "°C"
    y_unit: "mV"
  - file: "lt3042/curves/en-uv-turn-on-threshold.csv"
    caption: "EN/UV Turn-On Threshold"
    figure: "lt3042/figures/lt3042-f022.png"
    page: 7
    x_unit: "°C"
    y_unit: "V"
  - file: "lt3042/curves/enable-pin-current.csv"
    caption: "Enable Pin Current"
    figure: "lt3042/figures/lt3042-f029.png"
    page: 8
    x_unit: "V"
    y_unit: "µA"
  - file: "lt3042/curves/enable-pin-input-current.csv"
    caption: "Enable Pin Input Current"
    figure: "lt3042/figures/lt3042-f026.png"
    page: 8
    x_unit: "V"
    y_unit: "µA"
    conditions: "VIN = 20V"
  - file: "lt3042/curves/gnd-pin-current-3042-g16.csv"
    caption: "GND Pin Current (3042 G16)"
    figure: "lt3042/figures/lt3042-f018.png"
    page: 7
    x_unit: "°C"
    y_unit: "mA"
    conditions: "VIN = 5V, RSET = 33.2kΩ"
  - file: "lt3042/curves/gnd-pin-current-3042-g17.csv"
    caption: "GND Pin Current (3042 G17)"
    figure: "lt3042/figures/lt3042-f021.png"
    page: 7
    x_unit: "mA"
    y_unit: "mA"
    conditions: "VIN = 4.3V, RSET = 33.2kΩ"
  - file: "lt3042/curves/gnd-pin-current-3042-g18.csv"
    caption: "GND Pin Current (3042 G18)"
    figure: "lt3042/figures/lt3042-f024.png"
    page: 7
    x_unit: "V"
    y_unit: "mA"
    conditions: "RSET = 33.2kΩ"
  - file: "lt3042/curves/ilim-pin-current.csv"
    caption: "ILIM Pin Current"
    figure: "lt3042/figures/lt3042-f035.png"
    page: 9
    x_unit: "mA"
    y_unit: "µA"
    conditions: "V_ILIM = 0V, R_SET = 33.2kΩ"
  - file: "lt3042/curves/input-pair-p-10.csv"
    caption: "Power Supply Ripple Rejection as a Function of Error Amplifier Input Pair"
    figure: "lt3042/figures/lt3042-f049.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VIN = VOUT + 2V, IL = 200mA, COUT = 4.7µF, CSET = 0.47µF"
  - file: "lt3042/curves/input-pin-current.csv"
    caption: "Input Pin Current"
    figure: "lt3042/figures/lt3042-f027.png"
    page: 8
    x_unit: "V"
    y_unit: "mA"
    conditions: "VIN = 2V"
  - file: "lt3042/curves/integrated-rms-output-noise-10hz-to-100khz-3042-g46.csv"
    caption: "Integrated RMS Output Noise (10Hz to 100kHz) (3042 G46)"
    figure: "lt3042/figures/lt3042-f046.png"
    page: 10
    x_unit: "mA"
    y_unit: "µVRMS"
    conditions: "VIN = 5V, RSET = 33.2kΩ, COUT = 4.7µF, CSET = 4.7µF"
  - file: "lt3042/curves/integrated-rms-output-noise-10hz-to-100khz-3042-g47.csv"
    caption: "Integrated RMS Output Noise (10Hz to 100kHz) (3042 G47)"
    figure: "lt3042/figures/lt3042-f050.png"
    page: 10
    x_unit: "µF"
    y_unit: "µVRMS"
    conditions: "VIN = 5V, RSET = 33.2kΩ, COUT = 4.7µF, IL = 200mA"
  - file: "lt3042/curves/integrated-rms-output-noise-10hz-to-100khz-3042-g48.csv"
    caption: "Integrated RMS Output Noise (10Hz to 100kHz) (3042 G48)"
    figure: "lt3042/figures/lt3042-f053.png"
    page: 10
    x_unit: "V"
    y_unit: "µVRMS"
    conditions: "VIN = VOUT + 2V, CSET = 4.7µF, COUT = 4.7µF, ILOAD = 200mA"
  - file: "lt3042/curves/internal-current-limit-3042-g26.csv"
    caption: "Internal Current Limit (3042 G26)"
    figure: "lt3042/figures/lt3042-f030.png"
    page: 8
    x_unit: "°C"
    y_unit: "mA"
    conditions: "R_ILIM = 0Ω, V_OUT = 0V"
  - file: "lt3042/curves/internal-current-limit-3042-g27.csv"
    caption: "Internal Current Limit (3042 G27)"
    figure: "lt3042/figures/lt3042-f033.png"
    page: 8
    x_unit: "°C"
    y_unit: "mA"
    conditions: "V_IN = 20V, R_ILIM = 0Ω, V_OUT = 0V"
  - file: "lt3042/curves/internal-current-limit-3042-g28.csv"
    caption: "Internal Current Limit (3042 G28)"
    figure: "lt3042/figures/lt3042-f028.png"
    page: 8
    x_unit: "V"
    y_unit: "mA"
    conditions: "R_ILIM = 0Ω"
  - file: "lt3042/curves/iset-during-start-up-with-fast-start-up-enabled-3042-g36.csv"
    caption: "ISET During Start-Up with Fast Start-Up Enabled (3042 G36)"
    figure: "lt3042/figures/lt3042-f042.png"
    page: 9
    x_unit: "°C"
    y_unit: "mA"
    conditions: "V_IN = 2.5V, V_PGFB = 290mV, V_SET = 1.3V"
  - file: "lt3042/curves/iset-during-start-up-with-fast-start-up-enabled-3042-g37.csv"
    caption: "ISET During Start-Up with Fast Start-Up Enabled (3042 G37)"
    figure: "lt3042/figures/lt3042-f037.png"
    page: 9
    x_unit: "V"
    y_unit: "mA"
    conditions: "VPGFB = 290mV, VSET = 1.3V"
  - file: "lt3042/curves/load-regulation.csv"
    caption: "Load Regulation"
    figure: "lt3042/figures/lt3042-f014.png"
    page: 6
    x_unit: "°C"
    y_unit: "nA"
    conditions: "V_IN = 2.5V, ΔI_L = 1mA TO 200mA, V_OUT = 1.3V"
  - file: "lt3042/curves/minimum-input-voltage.csv"
    caption: "Minimum Input Voltage"
    figure: "lt3042/figures/lt3042-f019.png"
    page: 7
    x_unit: "°C"
    y_unit: "V"
  - file: "lt3042/curves/negative-enable-pin-current.csv"
    caption: "Negative Enable Pin Current"
    figure: "lt3042/figures/lt3042-f032.png"
    page: 8
    x_unit: "V"
    y_unit: "µA"
    conditions: "VIN = 2V"
  - file: "lt3042/curves/offset-voltage-vout-vset.csv"
    caption: "Offset Voltage (VOUT – VSET)"
    figure: "lt3042/figures/lt3042-f013.png"
    page: 6
    x_unit: "V"
    y_unit: "mV"
    conditions: "IL = 1mA, VOUT = 1.3V"
  - file: "lt3042/curves/offset-voltage-vout-vset-p-5.csv"
    caption: "Offset Voltage (VOUT – VSET) (p. 5)"
    figure: "lt3042/figures/lt3042-f007.png"
    page: 5
    x_unit: "°C"
    y_unit: "mV"
    conditions: "VIN = 2V, IL = 1mA, VOUT = 1.3V"
  - file: "lt3042/curves/output-overshoot-recovery-current-sink-3042-g38.csv"
    caption: "Output Overshoot Recovery Current Sink (3042 G38)"
    figure: "lt3042/figures/lt3042-f040.png"
    page: 9
    x_unit: "mV"
    y_unit: "mA"
    conditions: "VIN = 5V, RSET = 33.2kΩ"
  - file: "lt3042/curves/output-overshoot-recovery-current-sink-3042-g39.csv"
    caption: "Output Overshoot Recovery Current Sink (3042 G39)"
    figure: "lt3042/figures/lt3042-f043.png"
    page: 9
    x_unit: "°C"
    y_unit: "mA"
    conditions: "VIN = 5V, RSET = 33.2kΩ, VOUT – VSET > 5mV"
  - file: "lt3042/curves/pg-output-low-voltage.csv"
    caption: "PG Output Low Voltage"
    figure: "lt3042/figures/lt3042-f036.png"
    page: 9
    x_unit: "°C"
    y_unit: "mV"
    conditions: "VIN = 2V, VPGFB = 290mV, IPG = 100µA"
  - file: "lt3042/curves/pg-pin-leakage-current.csv"
    caption: "PG Pin Leakage Current"
    figure: "lt3042/figures/lt3042-f039.png"
    page: 9
    x_unit: "°C"
    y_unit: "nA"
    conditions: "V_PG = 2V, V_PGFB = 310mV"
  - file: "lt3042/curves/pgfb-hysteresis.csv"
    caption: "PGFB Hysteresis"
    figure: "lt3042/figures/lt3042-f041.png"
    page: 9
    x_unit: "°C"
    y_unit: "mV"
    conditions: "VIN = 2V"
  - file: "lt3042/curves/pgfb-rising-threshold.csv"
    caption: "PGFB Rising Threshold"
    figure: "lt3042/figures/lt3042-f038.png"
    page: 9
    x_unit: "°C"
    y_unit: "mV"
    conditions: "VIN = 2V"
  - file: "lt3042/curves/power-supply-ripple-rejection-3042-g41.csv"
    caption: "Power Supply Ripple Rejection (3042 G41)"
    figure: "lt3042/figures/lt3042-f048.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VIN = 5V, RSET = 33.2kΩ, COUT = 4.7µF, IL = 200mA"
  - file: "lt3042/curves/power-supply-ripple-rejection-3042-g42.csv"
    caption: "Power Supply Ripple Rejection (3042 G42)"
    figure: "lt3042/figures/lt3042-f051.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VIN = 5V, RSET = 33.2kΩ, CSET = 0.47µF, IL = 200mA"
  - file: "lt3042/curves/power-supply-ripple-rejection-3042-g43.csv"
    caption: "Power Supply Ripple Rejection (3042 G43)"
    figure: "lt3042/figures/lt3042-f045.png"
    page: 10
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VIN = 5V, RSET = 33.2kΩ, COUT = 4.7µF, CSET = 0.47µF"
  - file: "lt3042/curves/power-supply-ripple-rejection-3042-g45.csv"
    caption: "Power Supply Ripple Rejection (3042 G45)"
    figure: "lt3042/figures/lt3042-f052.png"
    page: 10
    x_unit: "V"
    y_unit: "dB"
    conditions: "IL = 200mA, RSET = 33.2kΩ, COUT = 4.7µF, CSET = 0.47µF"
  - file: "lt3042/curves/power-supply-ripple-rejection-p-1.csv"
    caption: "Power Supply Ripple Rejection (p. 1)"
    figure: "lt3042/figures/lt3042-f002.png"
    page: 1
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "VIN = 5V, RSET = 33.2kΩ, CSET = 4.7µF, COUT = 4.7µF, IL = 200mA"
  - file: "lt3042/curves/programmable-current-limit-3042-g29.csv"
    caption: "Programmable Current Limit (3042 G29)"
    figure: "lt3042/figures/lt3042-f031.png"
    page: 8
    x_unit: "°C"
    y_unit: "mA"
    conditions: "R_ILIM = 625Ω, V_OUT = 0V"
  - file: "lt3042/curves/programmable-current-limit-3042-g30.csv"
    caption: "Programmable Current Limit (3042 G30)"
    figure: "lt3042/figures/lt3042-f034.png"
    page: 8
    x_unit: "°C"
    y_unit: "mA"
    conditions: "R_ILIM = 2.49kΩ, V_OUT = 0V, V_IN = 7.5V and V_IN = 2.5V"
  - file: "lt3042/curves/quiescent-current-3042-g10.csv"
    caption: "Quiescent Current (3042 G10)"
    figure: "lt3042/figures/lt3042-f012.png"
    page: 6
    x_unit: "°C"
    y_unit: "mA"
    conditions: "VIN = 2V, VEN/UV = VIN, IL = 10µA, RSET = 13kΩ"
  - file: "lt3042/curves/quiescent-current-3042-g12.csv"
    caption: "Quiescent Current (3042 G12)"
    figure: "lt3042/figures/lt3042-f016.png"
    page: 6
    x_unit: "V"
    y_unit: "mA"
    conditions: "I_L = 10µA, R_SET = 33.2kΩ"
  - file: "lt3042/curves/quiescent-current-in-shutdown.csv"
    caption: "Quiescent Current in Shutdown"
    figure: "lt3042/figures/lt3042-f015.png"
    page: 6
    x_unit: "°C"
    y_unit: "µA"
    conditions: "VEN/UV = 0V"
  - file: "lt3042/curves/quiescent-current-p-7.csv"
    caption: "Quiescent Current (p. 7)"
    figure: "lt3042/figures/lt3042-f017.png"
    page: 7
    x_unit: "V"
    y_unit: "mA"
    conditions: "VIN = 20V, VEN/UV = VIN, IL = 10µA"
  - file: "lt3042/curves/set-pin-current-3042-g05.csv"
    caption: "SET Pin Current (3042 G05)"
    figure: "lt3042/figures/lt3042-f009.png"
    page: 6
    x_unit: "V"
    y_unit: "µA"
    conditions: "I_L = 1mA, V_OUT = 1.3V"
  - file: "lt3042/curves/set-pin-current-3042-g07.csv"
    caption: "SET Pin Current (3042 G07)"
    figure: "lt3042/figures/lt3042-f010.png"
    page: 6
    x_unit: "V"
    y_unit: "µA"
    conditions: "IL = 1mA, VIN = 20V"
  - file: "lt3042/curves/set-pin-current-p-5.csv"
    caption: "SET Pin Current (p. 5)"
    figure: "lt3042/figures/lt3042-f005.png"
    page: 5
    x_unit: "°C"
    y_unit: "µA"
    conditions: "VIN = 2V, IL = 1mA, VOUT = 1.3V"
  - file: "lt3042/curves/typical-dropout-voltage.csv"
    caption: "Typical Dropout Voltage"
    figure: "lt3042/figures/lt3042-f020.png"
    page: 7
    x_unit: "mA"
    y_unit: "mV"
    conditions: "RSET = 33.2kΩ"
  - file: "lt3042/curves/vout-forced-above-vout-nominal.csv"
    caption: "VOUT Forced Above VOUT(NOMINAL)"
    figure: "lt3042/figures/lt3042-f044.png"
    page: 10
    x_unit: "V"
    y_unit: "mA"
    conditions: "VIN = 5V, RSET = 33.2kΩ"
agentforge:
  part_number: "LT3042"
  datasheet_revision: "C"
  repairs: 1
  reading_order: "geometry"
---

# LT3042 — 20V, 200mA, Ultralow Noise, Ultrahigh PSRR RF Linear Regulator

*Datasheet: [LT3042 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/lt3042.pdf)*

### FEATURES
<!-- page: 1 -->

- **Ultralow RMS Noise: 0.8 $\mu V_{RMS}$ (10Hz to 100kHz)**
- **Ultralow Spot Noise: 2nV/√Hz at 10kHz**
- **Ultrahigh PSRR: 79dB at 1MHz**
- **Output Current: 200mA**
- **Wide Input Voltage Range: 1.8V to 20V**
- **Single Capacitor Improves Noise and PSRR**
- **100µA SET Pin Current: ±1% Initial Accuracy**
- Single Resistor Programs Output Voltage
- High Bandwidth: 1MHz
- Programmable Current Limit
- Low Dropout Voltage: 350mV
- Output Voltage Range: 0V to 15V
- Programmable Power Good
- Fast Start-Up Capability
- Precision Enable/UVLO
- Parallelable for Lower Noise and Higher Current
- Internal Current Limit with Foldback
- Minimum Output Capacitor: 4.7µF Ceramic
- Reverse Battery and Reverse Current Protection
- 10-Lead MSOP and 3mm × 3mm DFN Packages
- AEC-Q100 Qualified for Automotive Applications

### APPLICATIONS

- RF Power Supplies: PLLs, VCOs, Mixers, LNAs
- Very Low Noise Instrumentation
- High Speed/High Precision Data Converters
- Medical Applications: Imaging, Diagnostics
- Precision Power Supplies
- Post-Regulator for Switching Supplies

### DESCRIPTION

The [LT®3042](https://www.analog.com/LT3042?doc=LT3042.pdf) is a high performance low dropout linear regulator featuring LTC's ultralow noise and ultrahigh PSRR architecture for powering noise sensitive RF applications. Designed as a precision current reference followed by a high performance voltage buffer, the LT3042 can be easily paralleled to further reduce noise, increase output current and spread heat on the PCB.

The device supplies 200mA at a typical 350mV dropout voltage. Operating quiescent current is nominally 2mA and drops to <<1µA in shutdown. The LT3042's wide output voltage range (0V to 15V) while maintaining unitygain operation provides virtually constant output noise, PSRR, bandwidth and load regulation, independent of the programmed output voltage. Additionally, the regulator features programmable current limit, fast start-up capability and programmable power good to indicate output voltage regulation.

The LT3042 is stable with a minimum 4.7µF ceramic output capacitor. Built-in protection includes reverse battery protection, reverse current protection, internal current limit with foldback and thermal limit with hysteresis. The LT3042 is available in thermally enhanced 10-Lead MSOP and 3mm × 3mm DFN packages.

All registered trademarks and trademarks are the property of their respective owners. Patents Pending.

### TYPICAL APPLICATION

![Typical Application](lt3042/figures/lt3042-f001.png)

![Power Supply Ripple Rejection (p. 1)](lt3042/figures/lt3042-f002.png)

*Power Supply Ripple Rejection (p. 1)*

Digitized data: [power-supply-ripple-rejection-p-1.csv](lt3042/curves/power-supply-ripple-rejection-p-1.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

### ABSOLUTE MAXIMUM RATINGS (Note 1)
<!-- page: 2 -->

**Absolute Maximum Ratings (Note 1)** ([table-00-p2-abs_max.csv](lt3042/tables/table-00-p2-abs_max.csv), p. 2)

| PARAMETER | RATING |
|---|---|
| IN Pin Voltage | ±22V |
| EN/UV Pin Voltage | ±22V |
| IN-to-EN/UV Differential | ±22V |
| PG Pin Voltage (Note 10) | −0.3V, 22V |
| ILIM Pin Voltage (Note 10) | −0.3V, 1V |
| PGFB Pin Voltage (Note 10) | −0.3V, 22V |
| SET Pin Voltage (Note 10) | −0.3V, 16V |
| SET Pin Current (Note 7) | ±20mA |
| OUTS Pin Voltage (Note 10) | −0.3V, 16V |
| OUTS Pin Current (Note 7) | ±20mA |
| OUT Pin Voltage (Note 10) | −0.3V, 16V |
| OUT-to-OUTS Differential (Note 14) | ±1.2V |
| IN-to-OUT Differential | ±22V |
| IN-to-OUTS Differential | ±22V |
| Output Short-Circuit Duration | Indefinite |
| **Operating Junction Temperature Range (Note 9)** |  |
| E-, I-Grade | −40°C to 125°C |
| H-Grade | −40°C to 150°C |
| MP-Grade | −55°C to 150°C |
| Storage Temperature Range | −65°C to 150°C |
| **Lead Temperature (Soldering, 10 Sec)** |  |
| MSE Package | 300°C |

### PIN CONFIGURATION
<!-- page: 2 -->

![pinout (p. 2)](lt3042/figures/lt3042-f003.png)

![pinout (p. 2)](lt3042/figures/lt3042-f004.png)

### ORDER INFORMATION
<!-- pages: 2-3 -->

**Order Information** ([table-01-p2-data.csv](lt3042/tables/table-01-p2-data.csv), p. 2)

| LEAD FREE FINISH | TAPE AND REEL | PART MARKING* | PACKAGE DESCRIPTION | TEMPERATURE RANGE |
|---|---|---|---|---|
| LT3042EDD#PBF | LT3042EDD#TRPBF | LGSJ | 10-Lead (3mm × 3mm) Plastic DFN | –40°C to 125°C |
| LT3042IDD#PBF | LT3042IDD#TRPBF | LGSJ | 10-Lead (3mm × 3mm) Plastic DFN | –40°C to 125°C |
| LT3042HDD#PBF | LT3042HDD#TRPBF | LGSJ | 10-Lead (3mm × 3mm) Plastic DFN | –40°C to 150°C |
| LT3042MPDD#PBF | LT3042MPDD#TRPBF | LGSJ | 10-Lead (3mm × 3mm) Plastic DFN | –55°C to 150°C |
| LT3042EMSE#PBF | LT3042EMSE#TRPBF | LTGSH | 10-Lead Plastic MSOP | –40°C to 125°C |
| LT3042IMSE#PBF | LT3042IMSE#TRPBF | LTGSH | 10-Lead Plastic MSOP | –40°C to 125°C |
| LT3042HMSE#PBF | LT3042HMSE#TRPBF | LTGSH | 10-Lead Plastic MSOP | –40°C to 150°C |
| LT3042MPMSE#PBF | LT3042MPMSE#TRPBF | LTGSH | 10-Lead Plastic MSOP | –55°C to 150°C |
| **AUTOMOTIVE PRODUCTS**** |  |  |  |  |
| LT3042EMSE#WPBF | LT3042EMSE#WTRPBF | LTGSH | 10-Lead Plastic MSOP | −40°C to 125°C |
| LT3042IMSE#WPBF | LT3042IMSE#WTRPBF | LTGSH | 10-Lead Plastic MSOP | −40°C to 125°C |
| LT3042HMSE#WPBF | LT3042HMSE#WTRPBF | LTGSH | 10-Lead Plastic MSOP | −40°C to 150°C |

- Contact the factory for parts specified with wider operating temperature ranges. **\*:** The temperature grade is identified by a label on the shipping container.
- [Tape and reel specifications](https://www.analog.com/media/en/package-pcb-resources/package/tape-reel-rev-n.pdf). Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix
- **\*\*:** Versions of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These models are designated with a #W suffix. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models.

### ELECTRICAL CHARACTERISTICS
<!-- pages: 3-12 -->

The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at $T_{A}$ = 25°C.

**Electrical Characteristics** ([table-03-p3-spec.csv](lt3042/tables/table-03-p3-spec.csv), p. 3)

| PARAMETER | CONDITIONS | | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| Minimum IN Pin Voltage (Note 2) | $I_{LOAD}$ = 200mA, $V_{IN}$ UVLO Rising | ● |  | 1.78 | 2 | V |
| Minimum IN Pin Voltage (Note 2) | $V_{IN}$ UVLO Hysteresis |  |  | 75 |  | mV |
| SET Pin Current ($I_{SET}$) | $V_{IN}$ = 2V, $I_{LOAD}$ = 1mA, $V_{OUT}$ = 1.3V |  | 99 | 100 | 101 | µA |
| SET Pin Current ($I_{SET}$) | 2V < $V_{IN}$ < 20V, 0V < $V_{OUT}$ < 15V, 1mA < $I_{LOAD}$ < 200mA (Note 3) | ● | 98 | 100 | 102 | µA |
| Fast Start-Up Set Pin Current | $V_{PGFB}$ = 289mV, $V_{IN}$ = 2.8V, $V_{SET}$ = 1.3V |  |  | 2 |  | mA |
| Output Offset Voltage $V_{OS}$ ($V_{OUT}$ − $V_{SET}$) (Note 4) | $V_{IN}$ = 2V, $I_{LOAD}$ = 1mA, $V_{OUT}$ = 1.3V |  | −1 |  | 1 | mV |
| Output Offset Voltage $V_{OS}$ ($V_{OUT}$ − $V_{SET}$) (Note 4) | 2V < $V_{IN}$ < 20V, 0V < $V_{OUT}$ < 15V, 1mA < $I_{LOAD}$ < 200mA (Note 3) | ● | −2 |  | 2 | mV |
| Line Regulation: Δ$I_{SET}$ | $V_{IN}$ = 2V to 20V, $I_{LOAD}$ = 1mA, $V_{OUT}$ = 1.3V | ● |  | 0.5 | ±2 | nA/V |
| Line Regulation: Δ$V_{OS}$ | $V_{IN}$ = 2V to 20V, $I_{LOAD}$ = 1mA, $V_{OUT}$ = 1.3V (Note 4) | ● |  | 0.5 | ±3 | µV/V |
| Load Regulation: Δ$I_{SET}$ | $I_{LOAD}$ = 1mA to 200mA, $V_{IN}$ = 2V, $V_{OUT}$ = 1.3V |  |  | 3 |  | nA |
| Load Regulation: Δ$V_{OS}$ | $I_{LOAD}$ = 1mA to 200mA, $V_{IN}$ = 2V, $V_{OUT}$ = 1.3V (Note 4) | ● |  | 0.1 | 0.5 | mV |
| Change in $I_{SET}$ with $V_{SET}$ | $V_{SET}$ = 1.3V to 15V, $V_{IN}$ = 20V, $I_{LOAD}$ = 1mA | ● |  | 30 | 400 | nA |
| Change in $V_{OS}$ with $V_{SET}$ | $V_{SET}$ = 1.3V to 15V, $V_{IN}$ = 20V, $I_{LOAD}$ = 1mA (Note 4) | ● |  | 0.03 | 0.6 | mV |
| Change in $I_{SET}$ with $V_{SET}$ | $V_{SET}$ = 0V to 1.3V, $V_{IN}$ = 20V, $I_{LOAD}$ = 1mA | ● |  | 150 | 600 | nA |
| Change in $V_{OS}$ with $V_{SET}$ | $V_{SET}$ = 0V to 1.3V, $V_{IN}$ = 20V, $I_{LOAD}$ = 1mA (Note 4) | ● |  | 0.3 | 2 | mV |
| Dropout Voltage | $I_{LOAD}$ = 1mA, 50mA |  |  | 220 | 270 | mV |
| Dropout Voltage | $I_{LOAD}$ = 1mA, 50mA | ● |  |  | 300 | mV |
| Dropout Voltage | $I_{LOAD}$ = 150mA (Note 5) |  |  | 270 |  | mV |
| Dropout Voltage | $I_{LOAD}$ = 200mA (Note 5) |  |  | 350 |  | mV |
| GND Pin Current $V_{IN}$ = $V_{OUT(NOMINAL)}$ (Note 6) | $I_{LOAD}$ = 10µA |  |  | 1.9 |  | mA |
| GND Pin Current $V_{IN}$ = $V_{OUT(NOMINAL)}$ (Note 6) | $I_{LOAD}$ = 1mA | ● |  | 2 | 3.5 | mA |
| GND Pin Current $V_{IN}$ = $V_{OUT(NOMINAL)}$ (Note 6) | $I_{LOAD}$ = 50mA | ● |  | 3.2 | 5 | mA |
| GND Pin Current $V_{IN}$ = $V_{OUT(NOMINAL)}$ (Note 6) | $I_{LOAD}$ = 100mA | ● |  | 4.5 | 7 | mA |
| GND Pin Current $V_{IN}$ = $V_{OUT(NOMINAL)}$ (Note 6) | $I_{LOAD}$ = 200mA | ● |  | 7.6 | 13 | mA |
| Output Noise Spectral Density (Notes 4, 8) | $I_{LOAD}$ = 200mA, Frequency = 10Hz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF, $V_{OUT}$ = 3.3V |  |  | 300 |  | nV/√Hz |
| Output Noise Spectral Density (Notes 4, 8) | $I_{LOAD}$ = 200mA, Frequency = 10Hz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 4.7µF, 1.3V ≤ $V_{OUT}$ ≤ 15V |  |  | 60 |  | nV/√Hz |
| Output Noise Spectral Density (Notes 4, 8) | $I_{LOAD}$ = 200mA, Frequency = 10kHz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF, 1.3V ≤ $V_{OUT}$ ≤ 15V |  |  | 2 |  | nV/√Hz |
| Output Noise Spectral Density (Notes 4, 8) | $I_{LOAD}$ = 200mA, Frequency = 10kHz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF, 0V ≤ $V_{OUT}$ < 1.3V |  |  | 5 |  | nV/√Hz |
| Output RMS Noise (Notes 4, 8) | $I_{LOAD}$ = 200mA, BW = 10Hz to 100kHz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF, $V_{OUT}$ = 3.3V |  |  | 1.9 |  | $\mu V_{RMS}$ |
| Output RMS Noise (Notes 4, 8) | $I_{LOAD}$ = 200mA, BW = 10Hz to 100kHz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 4.7µF, 1.3V ≤ $V_{OUT}$ ≤ 15V |  |  | 0.8 |  | $\mu V_{RMS}$ |
| Output RMS Noise (Notes 4, 8) | $I_{LOAD}$ = 200mA, BW = 10Hz to 100kHz, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 4.7µF, 0V ≤ $V_{OUT}$ < 1.3V |  |  | 1.6 |  | $\mu V_{RMS}$ |
| Reference Current RMS Output Noise (Notes 4, 8) | BW = 10Hz to 100kHz |  |  | 6 |  | $nA_{RMS}$ |
| Ripple Rejection 1.3V ≤ $V_{OUT}$ ≤ 15V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 15) | $V_{RIPPLE}$ = 500 $mV_{P-P}$, $f_{RIPPLE}$ = 120Hz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 4.7µF |  | 95 | 117 |  | dB |
| Ripple Rejection 1.3V ≤ $V_{OUT}$ ≤ 15V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 15) | $V_{RIPPLE}$ = 150 $mV_{P-P}$, $f_{RIPPLE}$ = 10kHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 91 |  | dB |
| Ripple Rejection 1.3V ≤ $V_{OUT}$ ≤ 15V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 15) | $V_{RIPPLE}$ = 150 $mV_{P-P}$, $f_{RIPPLE}$ = 100kHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 78 |  | dB |
| Ripple Rejection 1.3V ≤ $V_{OUT}$ ≤ 15V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 15) | $V_{RIPPLE}$ = 150 $mV_{P-P}$, $f_{RIPPLE}$ = 1MHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 79 |  | dB |
| Ripple Rejection 1.3V ≤ $V_{OUT}$ ≤ 15V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 15) | $V_{RIPPLE}$ = 80 $mV_{P-P}$, $f_{RIPPLE}$ = 10MHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 56 |  | dB |
| Ripple Rejection 0V ≤ $V_{OUT}$ < 1.3V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 8) | $V_{RIPPLE}$ = 500 $mV_{P-P}$, $f_{RIPPLE}$ = 120Hz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 104 |  | dB |
| Ripple Rejection 0V ≤ $V_{OUT}$ < 1.3V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 8) | $V_{RIPPLE}$ = 50 $mV_{P-P}$, $f_{RIPPLE}$ = 10kHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 85 |  | dB |
| Ripple Rejection 0V ≤ $V_{OUT}$ < 1.3V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 8) | $V_{RIPPLE}$ = 50 $mV_{P-P}$, $f_{RIPPLE}$ = 100kHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 73 |  | dB |
| Ripple Rejection 0V ≤ $V_{OUT}$ < 1.3V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 8) | $V_{RIPPLE}$ = 50 $mV_{P-P}$, $f_{RIPPLE}$ = 1MHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 72 |  | dB |
| Ripple Rejection 0V ≤ $V_{OUT}$ < 1.3V $V_{IN}$ − $V_{OUT}$ = 2V (Avg) (Notes 4, 8) | $V_{RIPPLE}$ = 50 $mV_{P-P}$, $f_{RIPPLE}$ = 10MHz, $I_{LOAD}$ = 200mA, $C_{OUT}$ = 4.7µF, $C_{SET}$ = 0.47µF |  |  | 57 |  | dB |
| EN/UV Pin Threshold | EN/UV Trip Point Rising (Turn-On), $V_{IN}$ = 2V | ● | 1.18 | 1.24 | 1.32 | V |
| EN/UV Pin Hysteresis | EN/UV Trip Point Hysteresis, $V_{IN}$ = 2V |  |  | 170 |  | mV |
| EN/UV Pin Current | $V_{EN/UV}$ = 0V, $V_{IN}$ = 20V | ● |  |  | ±1 | µA |
| EN/UV Pin Current | $V_{EN/UV}$ = 1.24V, $V_{IN}$ = 20V |  |  | 0.2 |  | µA |
| EN/UV Pin Current | $V_{EN/UV}$ = 20V, $V_{IN}$ = 0V | ● |  | 8 | 15 | µA |
| Quiescent Current in Shutdown ($V_{EN/UV}$ = 0V) | $V_{IN}$ = 6V |  |  | 0.3 | 1 | µA |
| Quiescent Current in Shutdown ($V_{EN/UV}$ = 0V) |  | ● |  |  | 10 | µA |
| Internal Current Limit (Note 12) | $V_{IN}$ = 2V, $V_{OUT}$ = 0V | ● | 220 | 270 | 320 | mA |
| Internal Current Limit (Note 12) | $V_{IN}$ = 12V, $V_{OUT}$ = 0V |  |  | 300 |  | mA |
| Internal Current Limit (Note 12) | $V_{IN}$ = 20V, $V_{OUT}$ = 0V | ● | 130 | 180 | 250 | mA |
| Programmable Current Limit | Programming Scale Factor: 2V< $V_{IN}$ < 20V (Note 11) |  |  | 125 |  | mA • kΩ |
| Programmable Current Limit | $V_{IN}$ = 2V, $V_{OUT}$ = 0V, $R_{ILIM}$ = 625Ω | ● | 180 | 200 | 220 | mA |
| Programmable Current Limit | $V_{IN}$ = 2V, $V_{OUT}$ = 0V, $R_{ILIM}$ = 2.5kΩ | ● | 45 | 50 | 55 | mA |
| PGFB Trip Point | PGFB Trip Point Rising | ● | 291 | 300 | 309 | mV |
| PGFB Hysteresis | PGFB Trip Point Hysteresis |  |  | 7 |  | mV |
| PGFB Pin Current | $V_{IN}$ = 2V, $V_{PGFB}$ = 300mV |  |  | 25 |  | nA |
| PG Output Low Voltage | $I_{PG}$ = 100µA | ● |  | 30 | 100 | mV |
| PG Leakage Current | $V_{PG}$ = 20V | ● |  |  | 1 | µA |
| Reverse Input Current | $V_{IN}$ = −20V, $V_{EN/UV}$ = 0V, $V_{OUT}$ = 0V, $V_{SET}$ = 0V | ● |  |  | 50 | µA |
| Reverse Output Current | $V_{IN}$ = 0, $V_{OUT}$ = 5V, SET = Open |  |  | 2 | 5 | µA |
| Minimum Load Required (Note 13) | $V_{OUT}$ < 1V | ● | 10 |  |  | µA |
| Thermal Shutdown | $T_{J}$ Rising |  |  | 162 |  | °C |
| Thermal Shutdown | Hysteresis |  |  | 8 |  | °C |
| Start-Up Time | $V_{OUT(NOM)}$ = 5V, $I_{LOAD}$ = 200mA, $C_{SET}$ = 0.47µF, $V_{IN}$ = 6V, $V_{PGFB}$ = 6V |  |  | 55 |  | ms |
| Start-Up Time | $V_{OUT(NOM)}$ = 5V, $I_{LOAD}$ = 200mA, $C_{SET}$ = 4.7µF, $V_{IN}$ = 6V, $V_{PGFB}$ = 6V |  |  | 550 |  | ms |
| Start-Up Time | $V_{OUT(NOM)}$ = 5V, $I_{LOAD}$ = 200mA, $C_{SET}$ = 4.7µF, $V_{IN}$ = 6V, $R_{PG1}$ = 50kΩ, $R_{PG2}$ = 700kΩ (with Fast Start-Up to 90% of $V_{OUT}$) |  |  | 10 |  | ms |
| Thermal Regulation | 10ms Pulse |  |  | −0.01 |  | %/W |


Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.

Note 2: The EN/UV pin threshold must be met to ensure device operation.

Note 3: Maximum junction temperature limits operating conditions. The regulated output voltage specification does not apply for all possible combinations of input voltage and output current, especially due to the internal current limit foldback which starts to decrease current limit at $V_{IN}$ − $V_{OUT}$ > 12V. If operating at maximum output current, limit the input voltage range. If operating at the maximum input voltage, limit the output current range.

Note 4: OUTS ties directly to OUT.

Note 5: Dropout voltage is the minimum input-to-output differential voltage needed to maintain regulation at a specified output current. The dropout voltage is measured when output is 1% out of regulation. This definition results in a higher dropout voltage compared to hard dropout — which is measured when $V_{IN}$ = $V_{OUT(NOMINAL)}$. For lower output voltages, below 1.5V, dropout voltage is limited by the minimum input voltage specification. **Linear Technology is unable to guarantee maximum dropout voltage specifications at high currents due to production test limitations with Kelvin-sensing the package pins.** Please consult the Typical Performance Characteristics for curves of dropout voltage as a function of output load current and temperature measured in a typical application circuit.

Note 6: GND pin current is tested with $V_{IN}$ = $V_{OUT(NOMINAL)}$ and a current source load. Therefore, the device is tested while operating in dropout. This is the worst-case GND pin current. GND pin current decreases at higher input voltages. Note that GND pin current does not include SET pin or ILIM pin current but Quiescent current does include them.

Note 7: SET and OUTS pins are clamped using diodes and two 25Ω series resistors. For less than 5ms transients, this clamp circuitry can carry more than the rated current. Refer to Applications Information for more information.

Note 8: Adding a capacitor across the SET pin resistor decreases output voltage noise. Adding this capacitor bypasses the SET pin resistor's thermal noise as well as the reference current's noise. The output noise then equals the error amplifier noise. Use of a SET pin bypass capacitor also increases start-up time.

Note 9: The LT3042 is tested and specified under pulsed load conditions such that $T_{J}$ ≈ $T_{A}$. The LT3042E is 100% tested at 25°C and performance is guaranteed from 0°C to 125°C. Specifications over the −40°C to 125°C operating temperature range are assured by design, characterization, and correlation with statistical process controls. The LT3042I is guaranteed over the full −40°C to 125°C operating temperature range. The LT3042MP is 100% tested and guaranteed over the full −55°C to 150°C operating temperature range. The LT3042H is 100% tested at the 150°C operating junction temperature. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C.

Note 10: Parasitic diodes exist internally between the ILIM, PG, PGFB, SET, OUTS, and OUT pins and the GND pin. Do not drive these pins more than 0.3V below the GND pin during a fault condition. These pins must remain at a voltage more positive than GND during normal operation.

Note 11: The current limit programming scale factor is specified while the internal backup current limit is not active. Note that the internal current limit has foldback protection for $V_{IN}$ − $V_{OUT}$ differentials greater than 12V.

Note 12: The internal back-up current limit circuitry incorporates foldback protection that decreases current limit for $V_{IN}$ − $V_{OUT}$ > 12V. Some level of output current is provided at all $V_{IN}$ − $V_{OUT}$ differential voltages. Consult the Typical Performance Characteristics graph for current limit vs $V_{IN}$ − $V_{OUT}$.

Note 13: For output voltages less than 1V, the LT3042 requires a 10µA minimum load current for stability.

Note 14: Maximum OUT-to-OUTS differential is guaranteed by design.

Note 15: The PSRR at 120Hz is guaranteed by design, characterization, and correlation with statistical process controls.

### TYPICAL PERFORMANCE CHARACTERISTICS $T_{J}$  = 25°C, unless otherwise noted.

![SET Pin Current (p. 5)](lt3042/figures/lt3042-f005.png)

*SET Pin Current (p. 5)*

Digitized data: [set-pin-current-p-5.csv](lt3042/curves/set-pin-current-p-5.csv) (x: °C; y: µA) — values read off the printed plot by the digitizer, not published data.

![SET Pin Current (p. 5, g. 2)](lt3042/figures/lt3042-f006.png)

*SET Pin Current (p. 5, g. 2)*

Digitized data: [curve-006.csv](lt3042/curves/curve-006.csv) (x: µA; y: ) — values read off the printed plot by the digitizer, not published data.

![Offset Voltage (VOUT – VSET) (p. 5)](lt3042/figures/lt3042-f007.png)

*Offset Voltage ($V_{OUT}$ – $V_{SET}$) (p. 5)*

Digitized data: [offset-voltage-vout-vset-p-5.csv](lt3042/curves/offset-voltage-vout-vset-p-5.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![Offset Voltage (p. 6, g. 4)](lt3042/figures/lt3042-f008.png)

*Offset Voltage (p. 6, g. 4)*

Digitized data: [curve-008.csv](lt3042/curves/curve-008.csv) (x: mV; y: ) — values read off the printed plot by the digitizer, not published data.

![SET Pin Current (3042 G05)](lt3042/figures/lt3042-f009.png)

*SET Pin Current (3042 G05)*

Digitized data: [set-pin-current-3042-g05.csv](lt3042/curves/set-pin-current-3042-g05.csv) (x: V; y: µA) — values read off the printed plot by the digitizer, not published data.

![SET Pin Current (3042 G07)](lt3042/figures/lt3042-f010.png)

*SET Pin Current (3042 G07)*

Digitized data: [set-pin-current-3042-g07.csv](lt3042/curves/set-pin-current-3042-g07.csv) (x: V; y: µA) — values read off the printed plot by the digitizer, not published data.

![Offset Voltage (VOUT – VSET)](lt3042/figures/lt3042-f011.png)

*Offset Voltage ($V_{OUT}$ – $V_{SET}$)*

Digitized data: [curve-011.csv](lt3042/curves/curve-011.csv) (x: V; y: V) — values read off the printed plot by the digitizer, not published data.

![Quiescent Current (3042 G10)](lt3042/figures/lt3042-f012.png)

*Quiescent Current (3042 G10)*

Digitized data: [quiescent-current-3042-g10.csv](lt3042/curves/quiescent-current-3042-g10.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Offset Voltage (VOUT – VSET)](lt3042/figures/lt3042-f013.png)

*Offset Voltage ($V_{OUT}$ – $V_{SET}$)*

Digitized data: [offset-voltage-vout-vset.csv](lt3042/curves/offset-voltage-vout-vset.csv) (x: V; y: mV) — values read off the printed plot by the digitizer, not published data.

![Load Regulation](lt3042/figures/lt3042-f014.png)

*Load Regulation*

Digitized data: [load-regulation.csv](lt3042/curves/load-regulation.csv) (x: °C; y: nA) — values read off the printed plot by the digitizer, not published data.

![Quiescent Current in Shutdown](lt3042/figures/lt3042-f015.png)

*Quiescent Current in Shutdown*

Digitized data: [quiescent-current-in-shutdown.csv](lt3042/curves/quiescent-current-in-shutdown.csv) (x: °C; y: µA) — values read off the printed plot by the digitizer, not published data.

![Quiescent Current (3042 G12)](lt3042/figures/lt3042-f016.png)

*Quiescent Current (3042 G12)*

Digitized data: [quiescent-current-3042-g12.csv](lt3042/curves/quiescent-current-3042-g12.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![Quiescent Current (p. 7)](lt3042/figures/lt3042-f017.png)

*Quiescent Current (p. 7)*

Digitized data: [quiescent-current-p-7.csv](lt3042/curves/quiescent-current-p-7.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![GND Pin Current (3042 G16)](lt3042/figures/lt3042-f018.png)

*GND Pin Current (3042 G16)*

Digitized data: [gnd-pin-current-3042-g16.csv](lt3042/curves/gnd-pin-current-3042-g16.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Minimum Input Voltage](lt3042/figures/lt3042-f019.png)

*Minimum Input Voltage*

Digitized data: [minimum-input-voltage.csv](lt3042/curves/minimum-input-voltage.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![Typical Dropout Voltage](lt3042/figures/lt3042-f020.png)

*Typical Dropout Voltage*

Digitized data: [typical-dropout-voltage.csv](lt3042/curves/typical-dropout-voltage.csv) (x: mA; y: mV) — values read off the printed plot by the digitizer, not published data.

![GND Pin Current (3042 G17)](lt3042/figures/lt3042-f021.png)

*GND Pin Current (3042 G17)*

Digitized data: [gnd-pin-current-3042-g17.csv](lt3042/curves/gnd-pin-current-3042-g17.csv) (x: mA; y: mA) — values read off the printed plot by the digitizer, not published data.

![EN/UV Turn-On Threshold](lt3042/figures/lt3042-f022.png)

*EN/UV Turn-On Threshold*

Digitized data: [en-uv-turn-on-threshold.csv](lt3042/curves/en-uv-turn-on-threshold.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![Dropout Voltage](lt3042/figures/lt3042-f023.png)

*Dropout Voltage*

Digitized data: [dropout-voltage.csv](lt3042/curves/dropout-voltage.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![GND Pin Current (3042 G18)](lt3042/figures/lt3042-f024.png)

*GND Pin Current (3042 G18)*

Digitized data: [gnd-pin-current-3042-g18.csv](lt3042/curves/gnd-pin-current-3042-g18.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![EN/UV Pin Hysteresis](lt3042/figures/lt3042-f025.png)

*EN/UV Pin Hysteresis*

Digitized data: [en-uv-pin-hysteresis.csv](lt3042/curves/en-uv-pin-hysteresis.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![Enable Pin Input Current](lt3042/figures/lt3042-f026.png)

*Enable Pin Input Current*

Digitized data: [enable-pin-input-current.csv](lt3042/curves/enable-pin-input-current.csv) (x: V; y: µA) — values read off the printed plot by the digitizer, not published data.

![Input Pin Current](lt3042/figures/lt3042-f027.png)

*Input Pin Current*

Digitized data: [input-pin-current.csv](lt3042/curves/input-pin-current.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![Internal Current Limit (3042 G28)](lt3042/figures/lt3042-f028.png)

*Internal Current Limit (3042 G28)*

Digitized data: [internal-current-limit-3042-g28.csv](lt3042/curves/internal-current-limit-3042-g28.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![Enable Pin Current](lt3042/figures/lt3042-f029.png)

*Enable Pin Current*

Digitized data: [enable-pin-current.csv](lt3042/curves/enable-pin-current.csv) (x: V; y: µA) — values read off the printed plot by the digitizer, not published data.

![Internal Current Limit (3042 G26)](lt3042/figures/lt3042-f030.png)

*Internal Current Limit (3042 G26)*

Digitized data: [internal-current-limit-3042-g26.csv](lt3042/curves/internal-current-limit-3042-g26.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Programmable Current Limit (3042 G29)](lt3042/figures/lt3042-f031.png)

*Programmable Current Limit (3042 G29)*

Digitized data: [programmable-current-limit-3042-g29.csv](lt3042/curves/programmable-current-limit-3042-g29.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Negative Enable Pin Current](lt3042/figures/lt3042-f032.png)

*Negative Enable Pin Current*

Digitized data: [negative-enable-pin-current.csv](lt3042/curves/negative-enable-pin-current.csv) (x: V; y: µA) — values read off the printed plot by the digitizer, not published data.

![Internal Current Limit (3042 G27)](lt3042/figures/lt3042-f033.png)

*Internal Current Limit (3042 G27)*

Digitized data: [internal-current-limit-3042-g27.csv](lt3042/curves/internal-current-limit-3042-g27.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Programmable Current Limit (3042 G30)](lt3042/figures/lt3042-f034.png)

*Programmable Current Limit (3042 G30)*

Digitized data: [programmable-current-limit-3042-g30.csv](lt3042/curves/programmable-current-limit-3042-g30.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![ILIM Pin Current](lt3042/figures/lt3042-f035.png)

*ILIM Pin Current*

Digitized data: [ilim-pin-current.csv](lt3042/curves/ilim-pin-current.csv) (x: mA; y: µA) — values read off the printed plot by the digitizer, not published data.

![PG Output Low Voltage](lt3042/figures/lt3042-f036.png)

*PG Output Low Voltage*

Digitized data: [pg-output-low-voltage.csv](lt3042/curves/pg-output-low-voltage.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![ISET During Start-Up with Fast Start-Up Enabled (3042 G37)](lt3042/figures/lt3042-f037.png)

*$I_{SET}$ During Start-Up with Fast Start-Up Enabled (3042 G37)*

Digitized data: [iset-during-start-up-with-fast-start-up-enabled-3042-g37.csv](lt3042/curves/iset-during-start-up-with-fast-start-up-enabled-3042-g37.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![PGFB Rising Threshold](lt3042/figures/lt3042-f038.png)

*PGFB Rising Threshold*

Digitized data: [pgfb-rising-threshold.csv](lt3042/curves/pgfb-rising-threshold.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![PG Pin Leakage Current](lt3042/figures/lt3042-f039.png)

*PG Pin Leakage Current*

Digitized data: [pg-pin-leakage-current.csv](lt3042/curves/pg-pin-leakage-current.csv) (x: °C; y: nA) — values read off the printed plot by the digitizer, not published data.

![Output Overshoot Recovery Current Sink (3042 G38)](lt3042/figures/lt3042-f040.png)

*Output Overshoot Recovery Current Sink (3042 G38)*

Digitized data: [output-overshoot-recovery-current-sink-3042-g38.csv](lt3042/curves/output-overshoot-recovery-current-sink-3042-g38.csv) (x: mV; y: mA) — values read off the printed plot by the digitizer, not published data.

![PGFB Hysteresis](lt3042/figures/lt3042-f041.png)

*PGFB Hysteresis*

Digitized data: [pgfb-hysteresis.csv](lt3042/curves/pgfb-hysteresis.csv) (x: °C; y: mV) — values read off the printed plot by the digitizer, not published data.

![ISET During Start-Up with Fast Start-Up Enabled (3042 G36)](lt3042/figures/lt3042-f042.png)

*$I_{SET}$ During Start-Up with Fast Start-Up Enabled (3042 G36)*

Digitized data: [iset-during-start-up-with-fast-start-up-enabled-3042-g36.csv](lt3042/curves/iset-during-start-up-with-fast-start-up-enabled-3042-g36.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Output Overshoot Recovery Current Sink (3042 G39)](lt3042/figures/lt3042-f043.png)

*Output Overshoot Recovery Current Sink (3042 G39)*

Digitized data: [output-overshoot-recovery-current-sink-3042-g39.csv](lt3042/curves/output-overshoot-recovery-current-sink-3042-g39.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![VOUT Forced Above VOUT(NOMINAL)](lt3042/figures/lt3042-f044.png)

*$V_{OUT}$ Forced Above $V_{OUT(NOMINAL)}$*

Digitized data: [vout-forced-above-vout-nominal.csv](lt3042/curves/vout-forced-above-vout-nominal.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![Power Supply Ripple Rejection (3042 G43)](lt3042/figures/lt3042-f045.png)

*Power Supply Ripple Rejection (3042 G43)*

Digitized data: [power-supply-ripple-rejection-3042-g43.csv](lt3042/curves/power-supply-ripple-rejection-3042-g43.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Integrated RMS Output Noise (10Hz to 100kHz) (3042 G46)](lt3042/figures/lt3042-f046.png)

*Integrated RMS Output Noise (10Hz to 100kHz) (3042 G46)*

Digitized data: [integrated-rms-output-noise-10hz-to-100khz-3042-g46.csv](lt3042/curves/integrated-rms-output-noise-10hz-to-100khz-3042-g46.csv) (x: mA; y: µVRMS) — values read off the printed plot by the digitizer, not published data.

![Power Supply Ripple Rejection (3042 G41)](lt3042/figures/lt3042-f048.png)

*Power Supply Ripple Rejection (3042 G41)*

Digitized data: [power-supply-ripple-rejection-3042-g41.csv](lt3042/curves/power-supply-ripple-rejection-3042-g41.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Power Supply Ripple Rejection as a Function of Error Amplifier Input Pair](lt3042/figures/lt3042-f049.png)

*Power Supply Ripple Rejection as a Function of Error Amplifier Input Pair*

Digitized data: [input-pair-p-10.csv](lt3042/curves/input-pair-p-10.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Integrated RMS Output Noise (10Hz to 100kHz) (3042 G47)](lt3042/figures/lt3042-f050.png)

*Integrated RMS Output Noise (10Hz to 100kHz) (3042 G47)*

Digitized data: [integrated-rms-output-noise-10hz-to-100khz-3042-g47.csv](lt3042/curves/integrated-rms-output-noise-10hz-to-100khz-3042-g47.csv) (x: µF; y: µVRMS) — values read off the printed plot by the digitizer, not published data.

![Power Supply Ripple Rejection (3042 G42)](lt3042/figures/lt3042-f051.png)

*Power Supply Ripple Rejection (3042 G42)*

Digitized data: [power-supply-ripple-rejection-3042-g42.csv](lt3042/curves/power-supply-ripple-rejection-3042-g42.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Power Supply Ripple Rejection (3042 G45)](lt3042/figures/lt3042-f052.png)

*Power Supply Ripple Rejection (3042 G45)*

Digitized data: [power-supply-ripple-rejection-3042-g45.csv](lt3042/curves/power-supply-ripple-rejection-3042-g45.csv) (x: V; y: dB) — values read off the printed plot by the digitizer, not published data.

![Integrated RMS Output Noise (10Hz to 100kHz) (3042 G48)](lt3042/figures/lt3042-f053.png)

*Integrated RMS Output Noise (10Hz to 100kHz) (3042 G48)*

Digitized data: [integrated-rms-output-noise-10hz-to-100khz-3042-g48.csv](lt3042/curves/integrated-rms-output-noise-10hz-to-100khz-3042-g48.csv) (x: V; y: µVRMS) — values read off the printed plot by the digitizer, not published data.

![Noise Spectral Density (3042 G49)](lt3042/figures/lt3042-f054.png)

*Noise Spectral Density (3042 G49)*

![Noise Spectral Density as a Function of Error Amplifier Input Pair](lt3042/figures/lt3042-f055.png)

*Noise Spectral Density as a Function of Error Amplifier Input Pair*

![Line Transient Response](lt3042/figures/lt3042-f056.png)

*Line Transient Response*

![Noise Spectral Density (3042 G50)](lt3042/figures/lt3042-f057.png)

*Noise Spectral Density (3042 G50)*

![Output Noise: 10Hz to 100kHz](lt3042/figures/lt3042-f058.png)

*Output Noise: 10Hz to 100kHz*

![Noise Spectral Density (3042 G51)](lt3042/figures/lt3042-f059.png)

*Noise Spectral Density (3042 G51)*

![Load Transient Response](lt3042/figures/lt3042-f060.png)

*Load Transient Response*

![Start-Up Time with and without Fast Start-Up Circuitry for Large CSET](lt3042/figures/lt3042-f061.png)

*Start-Up Time with and without Fast Start-Up Circuitry for Large $C_{SET}$*

![Input Supply Ramp-Up and Ramp-Down](lt3042/figures/lt3042-f062.png)

*Input Supply Ramp-Up and Ramp-Down*

### PIN FUNCTIONS
<!-- pages: 12-13 -->

**IN (Pins 1, 2):** Input. These pins supply power to the regulator. The LT3042 requires a bypass capacitor at the IN pin. In general, a battery's output impedance rises with frequency, so include a bypass capacitor in battery-powered applications. While a 4.7µF input bypass capacitor generally suffices, applications with large load transients may require higher input capacitance to prevent input supply droop. Consult the Applications Information section on the proper use of an input capacitor and its effect on circuit performance, in particular PSRR. The LT3042 withstands reverse voltages on IN with respect to GND, OUTS and OUT. In the case of a reversed input, which occurs if a battery is plugged-in backwards, the LT3042 acts as if a diode is in series with its input. Hence, no reverse current flows into the LT3042 and no negative voltage appears at the load. The device protects itself and the load.

**EN/UV (Pin 3):** Enable/UVLO. Pulling the LT3042's EN/UV pin low places the part in shutdown. Quiescent current in shutdown drops to less than 1µA and the output voltage turns off. Alternatively, the EN/UV pin can set an input supply undervoltage lockout (UVLO) threshold using a resistor divider between IN, EN/UV and GND. The LT3042 typically turns on when the EN/UV voltage exceeds 1.24V on its rising edge, with a 170mV hysteresis on its falling edge. The EN/UV pin can be driven above the input voltage and maintain proper functionality. If unused, tie EN/UV to IN. Do not float the EN/UV pin.

**PG (Pin 4):** Power Good. PG is an open-collector flag that indicates output voltage regulation. PG pulls low if PGFB is below 300mV. If the power good functionality is not needed, float the PG pin. A parasitic substrate diode exists between PG and GND pins of the LT3042; do not drive PG more than 0.3V below GND during normal operation or during a fault condition.

**ILIM (Pin 5):** Current Limit Programming Pin. Connecting a resistor between ILIM and GND programs the current limit. For best accuracy, Kelvin connect this resistor directly to the LT3042's GND pin. The programming scale factor is nominally 125mA·kΩ. The ILIM pin sources current proportional (1:400) to output current; therefore, it also serves as a current monitoring pin with a 0V to 300mV range. If the programmable current limit functionality is not needed, tie ILIM to GND. A parasitic substrate diode exists between ILIM and GND pins of the LT3042; do not drive ILIM more than 0.3V below GND during normal operation or during a fault condition.

**PGFB (Pin 6):** Power Good Feedback. The PG pin pulls high if PGFB increases beyond 300mV on its rising edge, with 7mV hysteresis on its falling edge. Connecting an external resistor divider between OUT, PGFB and GND sets the programmable power good threshold with the following transfer function: 0.3V · (1 + $R_{PG2}$/$R_{PG1}$). As discussed in the Applications Information section, PGFB also activates the fast start-up circuitry. Tie PGFB to IN if power good and fast start-up functionalities are not needed, and if reverse input protection is additionally required, tie the anode of a 1N4148 diode to IN and its cathode to PGFB. See the Typical Applications section for details. A parasitic substrate diode exists between PGFB and GND pins of the LT3042; do not drive PGFB more than 0.3V below GND during normal operation or during a fault condition.

**SET (Pin 7):** SET. This pin is the inverting input of the error amplifier and the regulation set-point for the LT3042. SET sources a precision 100µA current that flows through an external resistor connected between SET and GND. The LT3042's output voltage is determined by $V_{SET}$ = $I_{SET}$ · $R_{SET}$. Output voltage range is from zero to 15V. Adding a capacitor from SET to GND improves noise, PSRR and transient response at the expense of increased start-up time. For optimum load regulation, Kelvin connect the ground side of the SET pin resistor directly to the load. A parasitic substrate diode exists between SET and GND pins of the LT3042; do not drive SET more than 0.3V below GND during normal operation or during a fault condition.

**GND (Pin 8, Exposed Pad Pin 11):** Ground. The exposed backside is an electrical connection to GND. To ensure proper electrical and thermal performance, solder the exposed backside to the PCB ground and tie it directly to the GND pin.

**OUTS (Pin 9):** Output Sense. This pin is the noninverting input to the error amplifier. For optimal transient performance and load regulation, Kelvin connect OUTS directly to the output capacitor and the load. Also, tie the GND connections of the output capacitor and the SET pin capacitor directly together. Moreover, place the input and output capacitors (and their GND connections) very close together. A parasitic substrate diode exists between OUTS and GND pins of the LT3042; do not drive OUTS more than 0.3V below GND during normal operation or during a fault condition.

**OUT (Pin 10):** Output. This pin supplies power to the load. For stability, use a minimum 4.7µF output capacitor with an ESR below 50mΩ and an ESL below 2nH. Large load transients require larger output capacitance to limit peak voltage transients. Refer to the Applications Information section for more information on output capacitance. A parasitic substrate diode exists between OUT and GND pins of the LT3042; do not drive OUT more than 0.3V below GND during normal operation or during a fault condition.

### BLOCK DIAGRAM
<!-- pages: 13-14 -->

![block diagram (p. 13)](lt3042/figures/lt3042-f063.png)

### APPLICATIONS INFORMATION
<!-- pages: 14-23 -->

The LT3042 is a high performance low dropout linear regulator featuring LTC's ultralow noise (2nV/√Hz at 10kHz) and ultrahigh PSRR (79dB at 1MHz) architecture for powering noise sensitive applications. Designed as a precision current source followed by a high performance rail-to-rail voltage buffer, the LT3042 can be easily paralleled to further reduce noise, increase output current and spread heat on the PCB. The device additionally features programmable current limit, fast start-up capability and programmable power good.

The LT3042 is easy to use and incorporates all of the protection features expected in high performance regulators. Included are short-circuit protection, safe operating area protection, reverse battery protection, reverse current protection, and thermal shutdown with hysteresis.

#### Output Voltage
<!-- page: 14 -->

The LT3042 incorporates a precision 100µA current source flowing out of the SET pin, which also ties to the error amplifier's inverting input. Figure 1 illustrates that connecting a resistor from SET to ground generates a reference voltage for the error amplifier. This reference voltage is simply the product of the SET pin current and the SET pin resistor. The error amplifier's unity-gain configuration produces a low impedance version of this voltage on its noninverting input, i.e. the OUTS pin, which is externally tied to the OUT pin.

The LT3042's rail-to-rail error amplifier and current reference allows for a wide output voltage range from 0V (using a 0Ω resistor) to $V_{IN}$ minus dropout - up to 15V. A PNP-based input pair is active for 0V to 0.6V output and an NPN-based input pair is active for output voltages greater than 1.3V, with a smooth transition between the two input pairs from 0.6V to 1.3V output. While the NPN-based input pair is designed to offer the best overall performance, refer to the Electrical Characteristics Table for details on offset voltage, SET pin current, output noise and PSRR variation with the error amp input pair. Table 1 lists many common output voltages and their corresponding 1%  $R_{SET}$ resistors.

![Figure 1. Basic Adjustable Regulator](lt3042/figures/lt3042-f064.png)

*Figure 1. Basic Adjustable Regulator*

**Table 1. 1% Resistor for Common Output Voltages** ([table-04-p14-data.csv](lt3042/tables/table-04-p14-data.csv), p. 14)

| $V_{OUT}$ (V) | $R_{SET}$ (kΩ) |
|---|---|
| 2.5 | 24.9 |
| 3.3 | 33.2 |
| 5 | 49.9 |
| 12 | 121 |
| 15 | 150 |

The benefit of using a current reference compared with a voltage reference as used in conventional regulators is that the regulator always operates in unity gain configuration, independent of the programmed output voltage. This allows the LT3042 to have loop gain, frequency response and bandwidth independent of the output voltage. As a result, noise, PSRR and transient performance do not change with output voltage. Moreover, since none of the error amp gain is needed to amplify the SET pin voltage to a higher output voltage, output load regulation is more tightly specified in the hundreds of microvolts range and not as a fixed percentage of the output voltage.

Since the zero TC current source is highly accurate, the SET pin resistor can become the limiting factor in achieving high accuracy. Hence, it should be a precision resistor. Additionally, any leakage paths to or from the SET pin create errors in the output voltage. If necessary, use high quality insulation (e.g., Teflon, Kel-F); moreover, cleaning of all insulating surfaces to remove fluxes and other residues may be required. High humidity environments may require a surface coating at the SET pin to provide a moisture barrier.

Minimize board leakage by encircling the SET pin with a guard ring operated at a potential close to itself - ideally tied to the OUT pin. Guarding both sides of the circuit board is recommended. Bulk leakage reduction depends on the guard ring width. Leakages of 100nA into or out of the SET pin creates a 0.1% error in the reference voltage. Leakages of this magnitude, coupled with other sources of leakage, can cause significant errors in the output voltage, especially over wide operating temperature range. Figure 2 illustrates a typical guard ring layout technique.

![Figure 2. Guard Ring Layout](lt3042/figures/lt3042-f065.png)

*Figure 2. Guard Ring Layout*

Since the SET pin is a high impedance node, unwanted signals may couple into the SET pin and cause erratic behavior. This is most noticeable when operating with a minimum output capacitor at heavy load currents. Bypassing the SET pin with a small capacitance to ground resolves this issue - 10nF is sufficient.

For applications requiring higher accuracy or an adjustable output voltage, the SET pin may be actively driven by an external voltage source capable of sinking 100µA. Connecting a precision voltage reference to the SET pin eliminates any errors present in the output voltage due to the reference current and SET pin resistor tolerances.

#### Output Sensing and Stability
<!-- page: 15 -->

The LT3042's OUTS pin provides a Kelvin sense connection to the output. The SET pin resistor's GND side provides a Kelvin sense connection to the load's GND side.

Additionally, for ultrahigh PSRR, the LT3042 bandwidth is made quite high (~1MHz), making it close to a typical 4.7µF (1206 case size) ceramic output capacitor's self-resonance frequency (~2.3MHz). Therefore, it is very important to avoid adding extra impedance (ESR and ESL) outside the feedback loop. To that end, as shown in Figure 3, minimize the effects of PCB trace and solder inductance by tying the OUTS pin directly to $C_{OUT}$ and the GND side of $C_{SET}$ directly to the GND side of $C_{OUT}$, as well as keep the GND sides of $C_{IN}$ and $C_{OUT}$ reasonably close. Refer to the LT3042 demo board manual for more information on the recommended layout that meets these requirements. While the LT3042 is robust enough not to oscillate if the recommended layout is not followed, depending on the actual layout, phase/gain margin, noise and PSRR performance may degrade.

![Figure 3. C OUT  and C SET  Connections for Stability](lt3042/figures/lt3042-f066.png)

*Figure 3. $C_{OUT}$ and $C_{SET}$ Connections for Stability*

#### Stability and Output Capacitance
<!-- page: 15 -->

The LT3042 requires an output capacitor for stability. Given its high bandwidth, LTC recommends low ESR and ESL ceramic capacitors. A minimum 4.7µF output capacitor with an ESR below 50mΩ and an ESL below 2nH is required for stability.

Given the high PSRR and low noise performance attained using a single 4.7µF ceramic output capacitor, larger values of output capacitor only marginally improves the performance because the regulator bandwidth decreases with increasing output capacitance - hence, there is little to be gained by using larger than the minimum 4.7µF output capacitor. Nonetheless, larger values of output capacitance do decrease peak output deviations during a load transient. Note that bypass capacitors used to decouple individual components powered by the LT3042 increase the effective output capacitance.

Give extra consideration to the type of ceramic capacitors used. They are manufactured with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics used are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are good for providing high capacitance in the small packages, but they tend to have stronger voltage and temperature coefficients as shown in Figure 4 and Figure 5. When used with a 5V regulator, a 16V 10µF Y5V capacitor can exhibit an effective value as low as 1µF to 2µF for the DC bias voltage applied over the operating temperature range.

X5R and X7R dielectrics result in more stable characteristics and are thus more suitable for LT3042. The X7R dielectric has better stability across temperature, while the X5R is less expensive and is available in higher values. Nonetheless, care must still be exercised when using X5R and X7R capacitors. The X5R and X7R codes only specify operating temperature range and the maximum capacitance change over temperature. While capacitance change due to DC bias for X5R and X7R is better than Y5V and Z5U dielectrics, it can still be significant enough to drop capacitance below sufficient levels. As shown in Figure 6, capacitor DC bias characteristics tend to improve as component case size increases, but verification of expected capacitance at the operating voltage is highly recommended.

![Figure 4. Ceramic Capacitor DC Bias Characteristics](lt3042/figures/lt3042-f067.png)

*Figure 4. Ceramic Capacitor DC Bias Characteristics*

Digitized data: [ceramic-capacitor-dc-bias-characteristics.csv](lt3042/curves/ceramic-capacitor-dc-bias-characteristics.csv) (x: V; y: %) — values read off the printed plot by the digitizer, not published data.

![Figure 5. Ceramic Capacitor Temperature Characteristics](lt3042/figures/lt3042-f068.png)

*Figure 5. Ceramic Capacitor Temperature Characteristics*

Digitized data: [ceramic-capacitor-temperature-characteristics.csv](lt3042/curves/ceramic-capacitor-temperature-characteristics.csv) (x: °C; y: %) — values read off the printed plot by the digitizer, not published data.

![Figure 6. Capacitor Voltage Coefficient for Different Case Sizes](lt3042/figures/lt3042-f069.png)

*Figure 6. Capacitor Voltage Coefficient for Different Case Sizes*

Digitized data: [capacitor-voltage-coefficient-for-different-case-sizes.csv](lt3042/curves/capacitor-voltage-coefficient-for-different-case-sizes.csv) (x: V; y: %) — values read off the printed plot by the digitizer, not published data.


#### High Vibration Environments
<!-- page: 16 -->

Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress upon it, similar to how a piezoelectric microphone works. For a ceramic capacitor, this stress can be induced by mechanical vibrations within the system or due to thermal transients.

LT3042 applications in high vibration environments have three distinct piezoelectric noise generators: ceramic output, input, and SET pin capacitors. However, due to LT3042's very low output impedance over a wide frequency range, negligible output noise is generated using a ceramic output capacitor. Similarly, due to LT3042's ultrahigh PSRR, negligible output noise is generated using a ceramic input capacitor. Nonetheless, given the high SET pin impedance, any piezoelectric response from a ceramic SET pin capacitor generates significant output noise - peak-to-peak excursions of hundreds of µVs. However, due to the SET pin capacitor's high ESR and ESL tolerance, any non-piezoelectrically responsive (tantalum, electrolytic, or film) capacitor can be used at the SET pin - although electrolytic capacitors tend to have high 1/f noise. In any case, use of surface mount capacitor is highly recommended.

#### Stability and Input Capacitance
<!-- page: 17 -->

The LT3042 is stable with a minimum 4.7µF IN pin capacitor. LTC recommends using low ESR ceramic capacitors. In cases where long wires connect the power supply to the LT3042's input and ground terminals, the use of low value input capacitors combined with a large load current can result in instability. The resonant LC tank circuit formed by the wire inductance and the input capacitor is the cause and not because of LT3042's instability.

The self-inductance, or isolated inductance, of a wire is directly proportional to its length. The wire diameter, however, has less influence on its self-inductance. For example, the self-inductance of a 2-AWG isolated wire with a diameter of 0.26" is about half the inductance of a 30-AWG wire with a diameter of 0.01". One foot of 30-AWG wire has 465nH of self-inductance.

Several methods exist to reduce a wire's self-inductance. One method divides the current flowing towards the LT3042 between two parallel conductors. In this case, placing the wires further apart reduces the inductance; up to a 50% reduction when placed only a few inches apart. Splitting the wires connect two equal inductors in parallel. However, when placed in close proximity to each other, their mutual inductance adds to the overall self inductance of the wires - therefore a 50% reduction is not possible in such cases. The second and more effective technique to reduce the overall inductance is to place the forward and return current conductors (the input and ground wires) in close proximity. Two 30-AWG wires separated by 0.02" reduce the overall inductance to about one-fifth of a single wire.

If a battery mounted in close proximity powers the LT3042, a 4.7µF input capacitor suffices for stability. However, if a distantly located supply powers the LT3042, use a larger value input capacitor. Use a rough guideline of 1µF (in addition to the 4.7µF minimum) per 8" of wire length.

The minimum input capacitance needed to stabilize the application also varies with the output capacitance as well as the load current. Placing additional capacitance on the LT3042's output helps. However, this requires significantly more capacitance compared to additional input bypassing. Series resistance between the supply and the LT3042 input also helps stabilize the application; as little as 0.1Ω to 0.5Ω suffices. This impedance dampens the LC tank circuit at the expense of dropout voltage. A better alternative is to use a higher ESR tantalum or electrolytic capacitor at the LT3042 input in parallel with a 4.7µF ceramic capacitor.

#### PSRR and Input Capacitance
<!-- page: 17 -->

*For applications utilizing the LT3042 for post-regulating switching converters, placing a capacitor directly at the LT3042 input results in ac current (at the switching frequency) to flow near the LT3042. This relatively high frequency switching current generates a magnetic field that couples to the LT3042 output, thereby degrading its effective PSRR. While highly dependent on the PCB, the switching pre-regulator, the input capacitance, amongst other factors, the PSRR degradation can be easily over 30dB at 1MHz. This degradation is present even if the LT3042 is de-soldered from the board, because it effectively degrades the PSRR of the PC board itself. While negligible for conventional low PSRR LDOs, LT3042's ultrahigh PSRR requires careful attention to higher order parasitics in order to extract the full performance offered by the regulator.*

*To mitigate the flow of high-frequency switching current near the LT3042, the LT3042 input capacitor can be entirely removed-as long as the switching converter's output capacitor is located more than an inch away from the LT3042. Magnetic coupling rapidly decreases with increasing distance. Nonetheless, if the switching pre-regulator is placed too far away (conservatively more than a couple inches) from the LT3042, with no input capacitor present, as with any regulator, the LT3042 input will oscillate at the parasitic LC resonance frequency. Besides, it is generally a very common (and a preferred) practice to bypass regulator input with some capacitance. So this option is fairly limited in its scope and not the most palatable solution.*

*To that end, LTC recommends using the LT3042 demo board (DC2246B) layout for achieving the best possible PSRR performance. The LT3042 demo board layout utilizes magnetic field cancellation techniques to prevent PSRR degradation caused by this high-frequency current flow-while utilizing the input capacitor.*

#### Filtering High Frequency Spikes
<!-- page: 18 -->

For applications where the LT3042 is used to post-regulate a switching converter, its high PSRR effectively suppresses any 'noise' present at the switcher's switching frequency - typically 100kHz to 4MHz. However, the very high frequency (100s of MHz) 'spikes' - beyond the LT3042's bandwidth - associated with the switcher's power switch transition times will almost directly pass through the LT3042. While the output capacitor is partly intended to absorb these spikes, its ESL will limit its ability at these frequencies. A ferrite bead or even the inductance associated with a short (e.g. 0.5") PCB trace between the switcher's output and the LT3042's input can serve as an LC-filter to suppress these very high frequency spikes.

#### Output Noise
<!-- page: 18 -->

The LT3042 offers many advantages with respect to noise performance. Traditional linear regulators have several sources of noise. The most critical noise sources for a traditional regulator are its voltage reference, error amplifier, noise from the resistor divider network used for setting output voltage and the noise gain created by this resistor divider. Many low noise regulators pin out their voltage reference to allow for noise reduction by bypassing the reference voltage.

Unlike most linear regulators, the LT3042 does not use a voltage reference; instead, it uses a $100\,\mu\text{A}$ current reference. The current reference operates with typical noise current level of $20\,\text{pA}/\sqrt{\text{Hz}}$ ($6\,\text{nA}_\text{RMS}$ over a $10\,\text{Hz}$ to $100\,\text{kHz}$ bandwidth). The resultant voltage noise equals the current noise multiplied by the resistor value, which in turn is RMS summed with the error amplifier's noise and the resistor's own noise of $\sqrt{4kTR}$ — whereby $k$ = Boltzmann's constant $1.38 \times 10^{-23}\,\text{J/K}$ and $T$ is the absolute temperature.



One problem that conventional linear regulators face is that the resistor divider setting the output voltage gains up the reference noise. In contrast, the LT3042's unity-gain follower architecture presents no gain from the SET pin to the output. Therefore, if a capacitor bypasses the SET pin resistor, then the output noise is independent of the programmed output voltage. The resultant output noise is then set just by the error amplifier's noise — typically $2\,\text{nV}/\sqrt{\text{Hz}}$ from 10kHz to 1MHz and $0.8\,\mu\text{V}_{\text{RMS}}$ in a 10Hz to 100kHz bandwidth using a 4.7µF SET pin capacitor. Paralleling multiple LT3042s further reduces noise by $\sqrt{N}$, for $N$ parallel regulators.

Refer to the Typical Performance Characteristics section for noise spectral density and RMS integrated noise over various load currents and SET pin capacitances.

#### Set Pin (Bypass) Capacitance: Noise, PSRR, Transient Response and Soft-Start
<!-- page: 18 -->

In addition to reducing output noise, using a SET pin bypass capacitor also improves PSRR and transient performance. Note that any bypass capacitor leakage deteriorates the LT3042's DC regulation. Capacitor leakage of even 100nA is a 0.1% DC error. Therefore, LTC recommends the use of a good quality low leakage ceramic capacitor.

Using a SET pin bypass capacitor also soft-starts the output and limits inrush current. The RC time constant, formed by the SET pin resistor and capacitor, controls soft-start time. Ramp-up rate from 0 to 90% of nominal $V_{OUT}$ is:

![Equation as printed (p. 18)](lt3042/figures/lt3042-eq01.png)

$$t_{SS} \approx 2.3 \cdot R_{SET} \cdot C_{SET} \left( \text{fast start-up disabled} \right)$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Fast Start-Up
<!-- page: 18 -->

For ultralow noise applications that require low 1/f noise (i.e. at frequencies below 100Hz), a larger value SET pin capacitor is required, up to 22µF. While normally this would significantly increase the regulator's start-up time, the LT3042 incorporates fast start-up circuitry that increases the SET pin current to about 2mA during start-up.

As shown in the Block Diagram, the 2mA current source remains engaged while PGFB is below 300mV, unless the regulator is in current limit, dropout, thermal shutdown or input voltage is below minimum $V_{IN}$.

If fast start-up capability is not used, tie PGFB to IN or to OUT for output voltages above 300mV. Note that doing so also disables power good functionality.

#### ENABLE/UVLO
<!-- page: 19 -->

The EN/UV pin is used to put the regulator into a micropower shutdown state. The LT3042 has an accurate 1.24V turn-on threshold on the EN/UV pin with 170mV of hysteresis. This threshold can be used in conjunction with a resistor divider from the input supply to define an accurate undervoltage lockout (UVLO) threshold for the regulator. The EN/UV pin current ($I_{EN}$) at the threshold from the Electrical Characteristics table needs to be considered when calculating the resistor divider network:

![Equation as printed (p. 19)](lt3042/figures/lt3042-eq02.png)

$$V_{IN(UVLO)} = 1.24V \cdot \left(1 + \frac{R_{EN2}}{R_{EN1}}\right) + I_{EN} \cdot R_{EN2}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The EN/UV pin current ($I_{EN}$) can be ignored if $R_{EN1}$ is less than 100k. If unused, tie EN/UV pin to IN.

#### Programmable Power Good
<!-- page: 19 -->

As illustrated in the Block Diagram, power good threshold is user programmable using the ratio of two external resistors, $R_{PG2}$ and $R_{PG1}$:

![Equation as printed (p. 19)](lt3042/figures/lt3042-eq03.png)

$$V_{OUT(PG\_THRESHOLD)} = 0.3V \cdot \left(1 + \frac{R_{PG2}}{R_{PG1}}\right) - I_{PGFB} \cdot R_{PG2}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

If the PGFB pin increases above 300mV, the open-collector PG pin de-asserts and becomes high impedance. The power good comparator has 7mV hysteresis and 5µs of deglitching. The PGFB pin current ($I_{PGFB}$) from the Electrical Characteristics table must be considered when determining the resistor divider network. The PGFB pin current ($I_{PGFB}$) can be ignored if $R_{PG1}$ is less than 30k. If power good functionality is not used, float the PG pin. Please note that programmable power good and fast start-up capabilities are disabled for output voltages below 300mV or when the device is in shutdown.

The power good functionality is disabled in shutdown, i.e. when EN/UV is set to 0V. If power good functionality is desired in shutdown, tie the power good resistor (i.e. RPG in the Block Diagram) between the PG pin and either the EN/UV or OUT pins.

#### Externally Programmable Current Limit
<!-- page: 19 -->

The ILIM pin's current limit threshold is 300mV. Connecting a resistor from ILIM to GND sets the maximum current flowing out of the ILIM pin, which in turn programs the LT3042's current limit. With a 125mA · kΩ programming scale factor, the current limit can be calculated as follows:

![Equation as printed (p. 19)](lt3042/figures/lt3042-eq04.png)

$$\text{Current Limit} = 125\text{mA} \cdot \frac{\text{k}\Omega}{R_{ILIM}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

For example, a 1kΩ resistor programs the current limit to 125mA and a 2kΩ resistor programs the current limit to 62.5mA. For good accuracy, Kelvin connect this resistor to the LT3042's GND pin.

In cases where IN-to-OUT differential is greater than 12V, the LT3042's foldback circuitry decreases the internal current limit. As a result, internal current limit may override the externally programmed current limit level to keep the LT3042 within its safe-operating-area (SOA). See the Internal Current Limit vs Input-to-Output Differential graph in the Typical Performance Characteristics section.

As shown in the Block Diagram, the ILIM pin sources current proportional (1:400) to output current; therefore, it also serves as a current monitoring pin with a 0V to 300mV range. If external current limit or current monitoring is not used, tie ILIM to GND.

#### Output Overshoot Recovery
<!-- page: 19 -->

During a load step from full load to no load (or light load), the output voltage overshoots before the regulator responds to turn the power transistor OFF. Given that there is no load (or very light load) present at the output, it takes a long time to discharge the output capacitor.

As illustrated in the Block Diagram, the LT3042 incorporates an overshoot recovery circuitry that turns on a current sink to discharge the output capacitor in the event OUTS is higher than SET. This current is typically about 4mA. No load recovery is disabled for input voltages less than 2.5V or output voltages less than 1.5V.

If OUTS is externally held above SET, the current sink turns ON in an attempt to restore OUTS to its programmed voltage. The current sink remains ON until the external circuitry releases OUTS.

#### Direct Paralleling for Higher Current
<!-- page: 20 -->

Higher output current is obtained by paralleling multiple LT3042s. Tie all SET pins together and all IN pins together. Connect the OUT pins together using small pieces of PCB trace (used as a ballast resistor) to equalize currents in the LT3042s. PCB trace resistance in milliohms/inch is shown in Table 2.

**Table 2. PC Board Trace Resistance** ([table-05-p20-data.csv](lt3042/tables/table-05-p20-data.csv), p. 20)

| WEIGHT (oz) | 10mil WIDTH | 20mil WIDTH |
|---|---|---|
| 1 | 54.3 | 27.1 |
| 2 | 27.1 | 13.6 |

- Trace resistance is measured in mΩ/in.

The small worst-case offset of 2mV for each paralleled LT3042 minimizes the required ballast resistor value. Figure 7 illustrates that two LT3042s, each using a 50mΩ PCB trace ballast resistor, provide better than 20% accurate output current sharing at full load. The two 50mΩ external resistors only add 10mV of output regulation drop with a 400mA maximum current. With a 3.3V output, this only adds 0.3% to the regulation accuracy. As has been discussed previously, tie the OUTS pin directly to the output capacitor.

![Figure 7. Parallel Devices](lt3042/figures/lt3042-f070.png)

*Figure 7. Parallel Devices*

More than two LT3042s can also be paralleled for even higher output current and lower output noise. Paralleling multiple LT3042s is also useful for distributing heat on the PCB. For applications with high input-to-output voltage differential, an input series resistor or resistor in parallel with the LT3042 can also be used to spread heat.

#### PCB Layout Considerations
<!-- page: 20 -->

Given the LT3042's high bandwidth and ultrahigh PSRR, careful PCB layout must be employed to achieve full device performance. Figure 8 shows an example layout that delivers full performance of the regulator. Refer to the LT3042's DC2246B demo board manual for further details.

![Figure 8. Example DFN Layout](lt3042/figures/lt3042-f072.png)

*Figure 8. Example DFN Layout*

#### Thermal Considerations
<!-- page: 21 -->

The LT3042 has internal power and thermal limiting circuits that protect the device under overload conditions. The thermal shutdown temperature is nominally 162°C with about 8°C of hysteresis. For continuous normal load conditions, do not exceed the maximum junction temperature, (125°C for E-, I-grades and 150°C for H-, MP-grades). It is important to consider all sources of thermal resistance from junction to ambient. This includes junction-to-case, case-to-heat sink interface, heat sink resistance or circuit board-to-ambient as the application dictates. Additionally, consider all heat sources in close proximity to the LT3042.

The undersides of the DFN and MSOP packages have exposed metal from the lead frame to the die attachment. Both packages allow heat to directly transfer from the die junction to the PCB metal to limit maximum operating junction temperature. The dual-in-line pin arrangement allows metal to extend beyond the ends of the package on the topside (component side) of the PCB.

For surface mount devices, heat sinking is accomplished by using the heat spreading capabilities of the PCB and its copper traces. Copper board stiffeners and plated throughholes can also be used to spread the heat generated by the regulator.

Table 3 and Table 4 list thermal resistance as a function of copper area on a fixed board size. All measurements were taken in still air on a 4 layer FR-4 board with 1oz solid internal planes and 2oz top/bottom planes with a total board thickness of 1.6mm. The four layers were electrically isolated with no thermal vias present. PCB layers, copper weight, board layout and thermal vias affect the resultant thermal resistance. For more information on thermal resistance and high thermal conductivity test boards, refer to JEDEC standard JESD51, notably JESD51-7 and JESD51-12. Achieving low thermal resistance necessitates attention to detail and careful PCB layout.

**Table 3. Measured Thermal Resistance for DFN Package** ([table-06-p21-data.csv](lt3042/tables/table-06-p21-data.csv), p. 21)

| COPPER AREA – TOP SIDE* | COPPER AREA – BOTTOM SIDE | BOARD AREA | THERMAL RESISTANCE |
|---|---|---|---|
| 2500 $mm^{2}$ | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 34°C/W |
| 1000 $mm^{2}$ | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 34°C/W |
| 225 $mm^{2}$  | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 35°C/W |
| 100 $mm^{2}$  | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 36°C/W |

\* Device is mounted on topside

**Table 4. Measured Thermal Resistance for MSOP Package** ([table-07-p21-data.csv](lt3042/tables/table-07-p21-data.csv), p. 21)

| COPPER AREA – TOP SIDE* | COPPER AREA – BOTTOM SIDE | BOARD AREA | THERMAL RESISTANCE |
|---|---|---|---|
| 2500 $mm^{2}$ | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 33°C/W |
| 1000 $mm^{2}$ | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 33°C/W |
| 225 $mm^{2}$  | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 34°C/W |
| 100 $mm^{2}$  | 2500 $mm^{2}$ | 2500 $mm^{2}$ | 35°C/W |

\* Device is mounted on topside

#### Calculating Junction Temperature
<!-- page: 21 -->

Example: Given an output voltage of 2.5V and input voltage of 5V ± 5%, output current range from 1mA to 200mA, and a maximum ambient temperature of 85°C, what is the maximum junction temperature? 

The LT3042's power dissipation is:

![Equation as printed (p. 21)](lt3042/figures/lt3042-eq05.png)

$$
\begin{aligned}
&I_{OUT(MAX)} \cdot \left(V_{IN(MAX)} - V_{OUT}\right) + I_{GND} \cdot V_{IN(MAX)} \\
&\text{where:} \\
&\quad I_{OUT(MAX)} = 200\text{mA} \\
&\quad V_{IN(MAX)} = 5.25\text{V} \\
&\quad I_{GND} \ (\text{at } I_{OUT} = 200\text{mA and } V_{IN} = 5.25\text{V}) = 7.2\text{mA} \\
&\text{thus:} \\
&\quad P_{DISS} = 0.2\text{A} \cdot (5.25\text{V} - 2.5\text{V}) + 7.2\text{mA} \cdot 5.25\text{V} = 0.59\text{W}
\end{aligned}
$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Using a DFN package, the thermal resistance is in the range of 34°C/W to 36°C/W depending on the copper area. Therefore, the junction temperature rise above ambient approximately equals:

![Equation as printed (p. 21)](lt3042/figures/lt3042-eq07.png)

$$0.59W \cdot 35^{\circ}\text{C/W} = 20.7^{\circ}\text{C}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The maximum junction temperature equals the maximum ambient temperature plus the maximum junction temperature rise above ambient:

![Equation as printed (p. 22)](lt3042/figures/lt3042-eq08.png)

$$T_{JMAX} = 85^{\circ}\text{C} + 20.7^{\circ}\text{C} = 105.7^{\circ}\text{C}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Overload Recovery
<!-- page: 22 -->

Like many IC power regulators, the LT3042 incorporates safe-operating-area (SOA) protection. The SOA protection activates at input-to-output differential voltages greater than 12V. The SOA protection decreases the current limit as the input-to-output differential increases and keeps the power transistor inside a safe operating region for all values of input-to-output voltages up to the LT3042's absolute maximum ratings. The LT3042 provides some level of output current for all values of input-to-output differentials. Refer to the Current Limit curves in the Typical Performance Characteristics section. When power is first applied and input voltage rises, the output follows the input and keeps the input-to-output differential low to allow the regulator to supply large output current and start-up into high current loads.

Due to current limit foldback, however, at high input voltages a problem can occur if the output voltage is low and the load current is high. Such situations occur after the removal of a short-circuit or if the EN/UV pin is pulled high after the input voltage has already turned ON. The load line in such cases intersects the output current profile at two points. The regulator now has two stable operating points. With this double intersection, the input power supply may need to be cycled down to zero and brought back up again to make the output recover. Other linear regulators with foldback current limit protection (such as the LT1965 and LT1963A, etc.) also exhibit this phenomenon, so it is not unique to the LT3042.

#### Protection Features
<!-- page: 22 -->

The LT3042 incorporates several protection features for battery-powered applications. Precision current limit and thermal overload protection protect the LT3042 against overload and fault conditions at the device's output. For normal operation, do not allow the junction temperature to exceed 125°C (E-, I-grade) or 150°C (H-, MP-grade).

To protect the LT3042's low noise error amplifier, the SET-to-OUTS protection clamp limits the maximum voltage between SET and OUTS with a maximum DC current of 20mA through the clamp. So for applications where SET is actively driven by a voltage source, the voltage source must be current limited to 20mA or less. Moreover, to limit the transient current flowing through these clamps during a transient fault condition, limit the maximum value of the SET pin capacitor ($C_{SET}$) to 22µF.

The LT3042 also incorporates reverse input protection whereby the IN pin withstands reverse voltages of up to -20V without causing any input current flow and without developing negative voltages at the OUT pin. The regulator protects both itself and the load against batteries that are plugged-in backwards.

In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to GND, pulled to some intermediate voltage, or left opencircuit. In all of these cases, the reverse current protection circuitry prevents current flow from output to the input. Nonetheless, due to the OUTS-to-SET clamp, unless the SET pin is floating, current can flow to GND through the SET pin resistor as well as up to 15mA to GND through the output overshoot recovery circuitry. This current flow through the output overshoot recovery circuitry can be significantly reduced by placing a Schottky diode between OUTS and SET pins, with its anode at the OUTS pin.

### TYPICAL APPLICATIONS
<!-- pages: 23-29 -->

![12VIN  to 3.3V OUT  with 0.8µV RMS  Integrated Noise](lt3042/figures/lt3042-f073.png)

*12 $V_{IN}$ to 3.3 $V_{OUT}$ with 0.8 $\mu V_{RMS}$ Integrated Noise*

![PGFB Disabled without Reverse Input Protection](lt3042/figures/lt3042-f074.png)

*PGFB Disabled without Reverse Input Protection*

![PGFB Disabled with Reverse Input Protection](lt3042/figures/lt3042-f075.png)

*PGFB Disabled with Reverse Input Protection*

![Low Noise CC/CV Lab Power Supply](lt3042/figures/lt3042-f076.png)

*Low Noise CC/CV Lab Power Supply*

![Programming Undervoltage Lockout](lt3042/figures/lt3042-f078.png)

*Programming Undervoltage Lockout*

![Ratiometric Tracking](lt3042/figures/lt3042-f079.png)

*Ratiometric Tracking*

![Ultralow 1/f Noise Reference Buffer](lt3042/figures/lt3042-f080.png)

*Ultralow 1/f Noise Reference Buffer*

![Paralleling Multiple Devices Using ILIM (Current Monitor) to Cancel Ballast Resistor Drop](lt3042/figures/lt3042-f081.png)

*Paralleling Multiple Devices Using ILIM (Current Monitor) to Cancel Ballast Resistor Drop*

![Paralleling Multiple LT3042s for Higher Output Current](lt3042/figures/lt3042-f083.png)

*Paralleling Multiple LT3042s for Higher Output Current*

![Ultralow Noise Higher Current Regulator with External PNP](lt3042/figures/lt3042-f085.png)

*Ultralow Noise Higher Current Regulator with External PNP*

![Ultralow Noise Higher Current Regulator with External NPN](lt3042/figures/lt3042-f086.png)

*Ultralow Noise Higher Current Regulator with External NPN*

#### Low Noise Wheatstone Bridge Power Supply
<!-- page: 28 -->

**Table** ([table-08-p28-data.csv](lt3042/tables/table-08-p28-data.csv), p. 28)

| RESISTOR TOLERANCE | BRIDGE PSRR | NOISE AT $V_{BRIDGE}$ USING LT1763 | NOISE AT $V_{BRIDGE}$ USING LT3042 |
|---|---|---|---|
| PERFECT MATCHING | INFINITE | – | – |
| 1% | 40dB | 200 $nV_{RMS}$ | 8 $nV_{RMS}$ |
| 5% | 26dB | 1000 $nV_{RMS}$ | 42.5 $nV_{RMS}$ |

![Low Noise Wheatstone Bridge Power Supply](lt3042/figures/lt3042-f087.png)

*Low Noise Wheatstone Bridge Power Supply*

### PACKAGE DESCRIPTION
<!-- pages: 29-31 -->

![DD Package 10-Lead Plastic DFN (3mm × 3mm)](lt3042/figures/lt3042-f088.png)

*DD Package 10-Lead Plastic DFN (3mm × 3mm)*

![MSE Package 10-Lead Plastic MSOP, Exposed Die Pad](lt3042/figures/lt3042-f090.png)

*MSE Package 10-Lead Plastic MSOP, Exposed Die Pad*

### REVISION HISTORY
<!-- pages: 31-32 -->

**Revision History** ([table-09-p31-data.csv](lt3042/tables/table-09-p31-data.csv), p. 31)

| REV | DATE | DESCRIPTION | PAGE NUMBER |
|---|---|---|---|
| A | 06/15 | Updated text in the second paragraph. | 1 |
| A | 06/15 | Updated Line Reg Δ$V_{OS}$, Change in $V_{OS}$, Output Noise Spectral Density specs. | 3 |
| A | 06/15 | Updated text to clarify fast start-up test condition. | 4 |
| A | 06/15 | Updated text to clarify Notes 5, 6, and 7. | 4 |
| A | 06/15 | Updated text to clarify Note 10. | 5 |
| A | 06/15 | Updated Graph 10 and Graph 12. | 6 |
| A | 06/15 | Updated conditions on Graph 18 and Graph 24. | 7 |
| A | 06/15 | Updated conditions on Graph 28. | 8 |
| A | 06/15 | Updated title of Graph 40. | 9 |
| A | 06/15 | Updated Output Voltage section. | 14, 15 |
| A | 06/15 | Updated Fast Start-up section. | 18 |
| A | 06/15 | Modified Direct Paralleling for Higher Current section. | 19 |
| A | 06/15 | Updated Typical Application circuit TA02. | 22 |
| A | 06/15 | Added Equation text to the Typical Application circuit TA03. | 22 |
| A | 06/15 | Updated Typical Application circuit TA06 and TA13. | 24 |
| A | 06/15 | Updated text in the Typical Application circuit TA14 and TA07. | 25 |
| A | 06/15 | Updated text in the Typical Application circuit TA08. | 26 |
| B | 11/17 | Modified Typical Application schematic. | 1 |
| B | 11/17 | Removed Ripple Rejection minimum spec in the Electrical Characteristics table. | 3 |
| B | 11/17 | Modified Start-Up Time conditions in the Electrical Characteristics table. | 4 |
| B | 11/17 | Revised Graph 37. | 9 |
| B | 11/17 | Changed scale on Graph 55. | 11 |
| B | 11/17 | Revised PGFB pin description in the Pin Functions section. | 12 |
| B | 11/17 | Modified Figure 3, and 'Output Sensing and Stability' and 'Stability and Output Capacitance' sections. | 15 |
| B | 11/17 | Added High Vibration Environments section. | 16 |
| B | 11/17 | Added PSRR + Input Capacitance section. | 17 |
| B | 11/17 | Revised Externally Programmable Current Limit section. | 19 |
| B | 11/17 | Revised Figure 8. | 20 |
| B | 11/17 | Modified Protection Features section. | 22 |
| C | 03/21 | Added AEC-Q100 Qualified for Automotive Applications to features table. | 1 |
| C | 03/21 | Added AUTOMOTIVE PRODUCTS** table plus supplemental text. | 2 |
| C | 03/21 | Added information to Programmable Power Good. | 19 |
| C | 03/21 | Updated $V_{OUT(PG\_ THRESHOLD)}$ formula. | 19 |

### TYPICAL APPLICATION
<!-- page: 32 -->

![Parallel Devices](lt3042/figures/lt3042-f091.png)

*Parallel Devices*

### RELATED PARTS
<!-- page: 32 -->

**Related Parts** ([table-10-p32-data.csv](lt3042/tables/table-10-p32-data.csv), p. 32)

| PART NUMBER | DESCRIPTION | COMMENTS |
|---|---|---|
| [LT1761](https://www.analog.com/LT1761?doc=LT3042.pdf) | 100mA, Low Noise LDO | 300mV Dropout Voltage, Low Noise: 20 $\mu V_{RMS}$, $V_{IN}$ = 1.8V to 20V |
| [LT1763](https://www.analog.com/LT1763?doc=LT3042.pdf) | 500mA, Low Noise LDO | 300mV Dropout Voltage, Low Noise: 20 $\mu V_{RMS}$, $V_{IN}$ = 1.8V to 20V, SO-8 Package |
| [LT3050](https://www.analog.com/LT3050?doc=LT3042.pdf) | 100mA LDO with Diagnostics and Precision Current Limit | 340mV Dropout Voltage, Low Noise: 30 $\mu V_{RMS}$, $V_{IN}$ = 1.8V to 45V, 3mm × 2mm DFN and MSOP Packages |
| [LT3060](https://www.analog.com/LT3060?doc=LT3042.pdf) | 100mA Low Noise LDO with Soft-Start | 300mV Dropout Voltage, Low Noise: 30 $\mu V_{RMS}$, $V_{IN}$ = 1.8V to 45V, 2mm × 2mm DFN and ThinSOT Packages |
| [LT3080](https://www.analog.com/LT3080?doc=LT3042.pdf) | 1.1A, Parallelable, Low Noise, Low Dropout Linear Regulator | 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40 $\mu V_{RMS}$, $V_{IN}$: 1.2V to 36V, $V_{OUT}$: 0V to 35.7V, Current-Based Reference with 1-Resistor $V_{OUT}$ Set; Directly Parallelable (No Op Amp Required), Stable with Ceramic Capacitors; TO-220, DD-Pak, SOT-223, MSOP and 3mm × 3mm DFN-8 Packages; LT3080-1 Version Has Integrated Internal Ballast Resistor |
| [LT3082](https://www.analog.com/LT3082?doc=LT3042.pdf) | 200mA, Parallelable, Low Noise LDO | Outputs May Be Paralleled for Higher Output Current or Heat Spreading, Wide Input Voltage Range: 1.2V to 40V, Low Value Input/Output Capacitors Required: 2.2µF, Single Resistor Sets Output Voltage, 8-Lead SOT-23, 3-Lead SOT-223 and 8-Lead 3mm × 3mm DFN Packages |
| [LT3085](https://www.analog.com/LT3085?doc=LT3042.pdf) | 500mA, Parallelable, Low Noise, Low Dropout Linear Regulator | 275mV Dropout (2-Supply Operation), Low Noise: 40 $\mu V_{RMS}$, $V_{IN}$: 1.2V to 36V, $V_{OUT}$: 0V to 35.7V, Current-Based Reference with 1-Resistor $V_{OUT}$ Set, Directly Parallelable (No Op Amp Required), Stable with Ceramic Capacitors; MS8E and 2mm × 3mm DFN-6 Packages |

