---
type: Analog Component
title: "ADAQ4224 — 24-Bit, 2 MSPS, μModule Data-Acquisition Solution"
description: "24-Bit, 2 MSPS, μModule Data-Acquisition Solution"
resource: "https://www.analog.com/en/products/adaq4224.html"
tags: ["datasheet", "adi"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/adaq4224.pdf"
    title: "ADAQ4224 data sheet"
    author: "team:analog-devices"
    last_modified: "2/2026"
tables:
  - file: "adaq4224/tables/table-00-p5-spec.csv"
    title: "Table 1. Specifications"
    page: 5
  - file: "adaq4224/tables/table-01-p9-spec.csv"
    title: "Table 2. Digital Timing Interface"
    page: 9
  - file: "adaq4224/tables/table-02-p9-spec.csv"
    title: "Table 3. Register Read/Write Timing"
    page: 9
  - file: "adaq4224/tables/table-03-p10-spec.csv"
    title: "Table 4. SPI-Compatible Mode Timing"
    page: 10
  - file: "adaq4224/tables/table-04-p11-spec.csv"
    title: "Table 5. Echo-Clock Mode Timing, SDR, 1-Lane"
    page: 11
  - file: "adaq4224/tables/table-06-p12-spec.csv"
    title: "Table 7. Host-Clock Mode Timing"
    page: 12
  - file: "adaq4224/tables/table-05-p12-spec.csv"
    title: "Table 6. Echo-Clock Mode Timing, DDR, 1-Lane"
    page: 12
  - file: "adaq4224/tables/table-07-p13-spec.csv"
    title: "Table 8. Temperature Sensor I2C Timing"
    page: 13
  - file: "adaq4224/tables/table-08-p14-abs_max.csv"
    title: "Table 9. Absolute Maximum Ratings"
    page: 14
  - file: "adaq4224/tables/table-09-p14-data.csv"
    title: "Table 10. Thermal Resistance"
    page: 14
  - file: "adaq4224/tables/table-10-p14-data.csv"
    title: "Table 11. ADAQ4224, 178-Ball CSP_BGA"
    page: 14
  - file: "adaq4224/tables/table-11-p15-pin.csv"
    title: "Table 12. Pin Function Descriptions"
    page: 15
  - file: "adaq4224/tables/table-12-p34-data.csv"
    title: "Table 13. Input Voltage to Output Code Mapping"
    page: 34
  - file: "adaq4224/tables/table-15-p36-data.csv"
    title: "Table 16. Temperature Data Format (S = Sign Bit)"
    page: 36
  - file: "adaq4224/tables/table-13-p36-data.csv"
    title: "Table 14. RSEL Resistor Selection of Device Address Bits[A4:A0]"
    page: 36
  - file: "adaq4224/tables/table-16-p37-register.csv"
    title: "Table 17. Conversion Rate Selection"
    page: 37
  - file: "adaq4224/tables/table-17-p37-register.csv"
    title: "Table 18. Resolution Selection"
    page: 37
  - file: "adaq4224/tables/table-18-p38-register.csv"
    title: "Table 19. Fault Queue Selection"
    page: 38
  - file: "adaq4224/tables/table-19-p47-data.csv"
    title: "Table 20. BUSY_SCKOUT Pin Behavior vs. Clocking Mode"
    page: 47
  - file: "adaq4224/tables/table-20-p52-data.csv"
    title: "Table 21. ADAQ4224 Supported Data Output Modes"
    page: 52
  - file: "adaq4224/tables/table-21-p53-spec.csv"
    title: "Table 22. Conversion Cycle Timing Parameters"
    page: 53
  - file: "adaq4224/tables/table-22-p59-register.csv"
    title: "Table 23. ADAQ4224 Register Summary"
    page: 59
  - file: "adaq4224/tables/table-23-p60-register.csv"
    title: "Table 24. Bit Descriptions for INTERFACE_CONFIG_A"
    page: 60
  - file: "adaq4224/tables/table-24-p60-register.csv"
    title: "Table 25. Bit Descriptions for INTERFACE_CONFIG_B"
    page: 60
  - file: "adaq4224/tables/table-25-p61-register.csv"
    title: "Table 26. Bit Descriptions for DEVICE_CONFIG"
    page: 61
  - file: "adaq4224/tables/table-26-p61-register.csv"
    title: "Table 27. Bit Descriptions for CHIP_TYPE"
    page: 61
  - file: "adaq4224/tables/table-27-p61-register.csv"
    title: "Table 28. Bit Descriptions for PRODUCT_ID_L"
    page: 61
  - file: "adaq4224/tables/table-28-p62-register.csv"
    title: "Table 29. Bit Descriptions for PRODUCT_ID_H"
    page: 62
  - file: "adaq4224/tables/table-29-p62-register.csv"
    title: "Table 30. Bit Descriptions for CHIP_GRADE"
    page: 62
  - file: "adaq4224/tables/table-30-p62-register.csv"
    title: "Table 31. Bit Descriptions for SCRATCH_PAD"
    page: 62
  - file: "adaq4224/tables/table-31-p62-register.csv"
    title: "Table 32. Bit Descriptions for SPI_REVISION"
    page: 62
  - file: "adaq4224/tables/table-32-p63-register.csv"
    title: "Table 33. Bit Descriptions for VENDOR_L"
    page: 63
  - file: "adaq4224/tables/table-33-p63-register.csv"
    title: "Table 34. Bit Descriptions for VENDOR_H"
    page: 63
  - file: "adaq4224/tables/table-34-p63-register.csv"
    title: "Table 35. Bit Descriptions for STREAM_MODE"
    page: 63
  - file: "adaq4224/tables/table-35-p63-register.csv"
    title: "Table 36. Bit Descriptions for INTERFACE_STATUS_A"
    page: 63
  - file: "adaq4224/tables/table-36-p64-register.csv"
    title: "Table 37. Bit Descriptions for EXIT_CFG_MD"
    page: 64
  - file: "adaq4224/tables/table-37-p64-register.csv"
    title: "Table 38. Bit Descriptions for AVG"
    page: 64
  - file: "adaq4224/tables/table-38-p65-register.csv"
    title: "Table 39. Bit Descriptions for OFFSET_LB"
    page: 65
  - file: "adaq4224/tables/table-39-p65-register.csv"
    title: "Table 40. Bit Descriptions for OFFSET_MB"
    page: 65
  - file: "adaq4224/tables/table-40-p65-register.csv"
    title: "Table 41. Bit Descriptions for OFFSET_HB"
    page: 65
  - file: "adaq4224/tables/table-41-p65-register.csv"
    title: "Table 42. Bit Descriptions for GAIN_LB"
    page: 65
  - file: "adaq4224/tables/table-42-p66-register.csv"
    title: "Table 43. Bit Descriptions for GAIN_HB"
    page: 66
  - file: "adaq4224/tables/table-43-p66-register.csv"
    title: "Table 44. Bit Descriptions for MODES"
    page: 66
  - file: "adaq4224/tables/table-44-p66-register.csv"
    title: "Table 45. Bit Descriptions for OSCILLATOR"
    page: 66
  - file: "adaq4224/tables/table-45-p67-register.csv"
    title: "Table 46. Bit Descriptions for IO"
    page: 67
  - file: "adaq4224/tables/table-46-p67-register.csv"
    title: "Table 47. Bit Descriptions for TEST_PAT_BYTE0"
    page: 67
  - file: "adaq4224/tables/table-47-p67-register.csv"
    title: "Table 48. Bit Descriptions for TEST_PAT_BYTE1"
    page: 67
  - file: "adaq4224/tables/table-48-p67-register.csv"
    title: "Table 49. Bit Descriptions for TEST_PAT_BYTE2"
    page: 67
  - file: "adaq4224/tables/table-49-p68-register.csv"
    title: "Table 50. Bit Descriptions for TEST_PAT_BYTE3"
    page: 68
  - file: "adaq4224/tables/table-50-p68-register.csv"
    title: "Table 51. Bit Descriptions for DIG_DIAG"
    page: 68
  - file: "adaq4224/tables/table-51-p68-register.csv"
    title: "Table 52. Bit Descriptions for DIG_ERR"
    page: 68
  - file: "adaq4224/tables/table-52-p69-register.csv"
    title: "Table 53. Temperature Sensor Register Summary"
    page: 69
  - file: "adaq4224/tables/table-53-p70-register.csv"
    title: "Table 54. Bit Descriptions for CONFIGURATION/STATUS Register"
    page: 70
  - file: "adaq4224/tables/table-54-p71-data.csv"
    title: "Ordering Guide"
    page: 71
  - file: "adaq4224/tables/table-55-p71-data.csv"
    title: "Evaluation Boards"
    page: 71
figures:
  - file: "adaq4224/figures/adaq4224-f110-01.png"
    caption: "Figure 108. Reference with Noise Filter"
    type: "other"
    page: 44
  - file: "adaq4224/figures/adaq4224-f110-02.png"
    caption: "Figure 109. CNV Waveform Showing Burst Sampling"
    type: "other"
    page: 44
  - file: "adaq4224/figures/adaq4224-f001.png"
    caption: "Figure 1. ADAQ4224 Functional Block Diagram"
    type: "block_diagram"
    page: 1
  - file: "adaq4224/figures/adaq4224-f002.png"
    caption: ""
    type: "other"
    page: 1
  - file: "adaq4224/figures/adaq4224-f003.png"
    caption: "Figure 2. Voltage Levels for Timing"
    type: "timing_diagram"
    page: 9
  - file: "adaq4224/figures/adaq4224-f004.png"
    caption: "Figure 3. Register Configuration Mode Write Timing"
    type: "timing_diagram"
    page: 10
  - file: "adaq4224/figures/adaq4224-f005.png"
    caption: "Figure 4. Register Configuration Mode Read Timing"
    type: "timing_diagram"
    page: 10
  - file: "adaq4224/figures/adaq4224-f006.png"
    caption: "Figure 5. Register Configuration Mode Command Timing"
    type: "timing_diagram"
    page: 10
  - file: "adaq4224/figures/adaq4224-f007.png"
    caption: "Figure 6. SPI Clocking Mode 1-Lane SDR Timing"
    type: "timing_diagram"
    page: 11
  - file: "adaq4224/figures/adaq4224-f008.png"
    caption: "Figure 7. Echo-Clock Mode Timing, SDR, 1-Lane"
    type: "timing_diagram"
    page: 12
  - file: "adaq4224/figures/adaq4224-f009.png"
    caption: "Figure 8. Echo-Clock Mode Timing, DDR, 1-Lane"
    type: "timing_diagram"
    page: 12
  - file: "adaq4224/figures/adaq4224-f010.png"
    caption: "Figure 9. Host-Clock Mode Timing, SDR, 1-Lane"
    type: "timing_diagram"
    page: 13
  - file: "adaq4224/figures/adaq4224-f011.png"
    caption: "Figure 10. Host-Clock Mode Timing, DDR, 1-Lane"
    type: "timing_diagram"
    page: 13
  - file: "adaq4224/figures/adaq4224-f012.png"
    caption: "Figure 11. Temperature Sensor I 2 C Timing Diagram"
    type: "timing_diagram"
    page: 13
  - file: "adaq4224/figures/adaq4224-f014.png"
    caption: "Figure 12. Pin Configuration (Top View)"
    type: "pinout"
    page: 15
  - file: "adaq4224/figures/adaq4224-f015.png"
    caption: "Figure 13. INL Error vs. Output Code, Differential Input, REFIN = 5 V"
    type: "characteristic_curve"
    page: 17
  - file: "adaq4224/figures/adaq4224-f016.png"
    caption: "Figure 14. INL Error vs. Output Code, Single-Ended Input, REFIN = 5 V"
    type: "characteristic_curve"
    page: 17
  - file: "adaq4224/figures/adaq4224-f017.png"
    caption: "Figure 15. INL Error vs. Output Code across Temperature, G = 1/3"
    type: "characteristic_curve"
    page: 17
  - file: "adaq4224/figures/adaq4224-f018.png"
    caption: "Figure 16. INL Error vs. Output Code, Differential Input, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 17
  - file: "adaq4224/figures/adaq4224-f019.png"
    caption: "Figure 17. INL Error vs. Output Code, Single-Ended Input, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 17
  - file: "adaq4224/figures/adaq4224-f020.png"
    caption: "Figure 18. INL Error vs. Output Code across Temperature, G = 5/9"
    type: "characteristic_curve"
    page: 17
  - file: "adaq4224/figures/adaq4224-f021.png"
    caption: "Figure 19. INL Error vs. Output Code across Temperature, G = 20/9"
    type: "characteristic_curve"
    page: 18
  - file: "adaq4224/figures/adaq4224-f022.png"
    caption: "Figure 20. Code Histogram for Shorted Inputs, REFIN = 5 V"
    type: "characteristic_curve"
    page: 18
  - file: "adaq4224/figures/adaq4224-f023.png"
    caption: "Figure 21. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 1/3"
    type: "characteristic_curve"
    page: 18
  - file: "adaq4224/figures/adaq4224-f024.png"
    caption: "Figure 22. INL Error vs. Output Code across Temperature, G = 20/3"
    type: "characteristic_curve"
    page: 18
  - file: "adaq4224/figures/adaq4224-f025.png"
    caption: "Figure 23. Code Histogram for Shorted Inputs, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 18
  - file: "adaq4224/figures/adaq4224-f026.png"
    caption: "Figure 24. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 1/3"
    type: "characteristic_curve"
    page: 18
  - file: "adaq4224/figures/adaq4224-f027.png"
    caption: "Figure 25. FFT, 2 MSPS, f_{IN} = 1 kHz , Differential Input = -0.5 dBFS, G = 5/9"
    type: "characteristic_curve"
    page: 19
  - file: "adaq4224/figures/adaq4224-f028.png"
    caption: "Figure 26. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/9"
    type: "characteristic_curve"
    page: 19
  - file: "adaq4224/figures/adaq4224-f029.png"
    caption: "Figure 27. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/3"
    type: "characteristic_curve"
    page: 19
  - file: "adaq4224/figures/adaq4224-f030.png"
    caption: "Figure 28. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 5/9"
    type: "characteristic_curve"
    page: 19
  - file: "adaq4224/figures/adaq4224-f031.png"
    caption: "Figure 29. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/9"
    type: "characteristic_curve"
    page: 19
  - file: "adaq4224/figures/adaq4224-f032.png"
    caption: "Figure 30. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/3"
    type: "characteristic_curve"
    page: 19
  - file: "adaq4224/figures/adaq4224-f033.png"
    caption: "Figure 31. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz"
    type: "characteristic_curve"
    page: 20
  - file: "adaq4224/figures/adaq4224-f034.png"
    caption: "Figure 32. SNR vs. Input Amplitude at f_{IN} = 20 kHz"
    type: "characteristic_curve"
    page: 20
  - file: "adaq4224/figures/adaq4224-f035.png"
    caption: "Figure 33. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 20
  - file: "adaq4224/figures/adaq4224-f036.png"
    caption: "Figure 34. SNR vs. Input Amplitude at f_{IN} = 50 kHz"
    type: "characteristic_curve"
    page: 20
  - file: "adaq4224/figures/adaq4224-f037.png"
    caption: "Figure 35. SNR vs. Input Amplitude at f_{IN} = 100 kHz"
    type: "characteristic_curve"
    page: 20
  - file: "adaq4224/figures/adaq4224-f038.png"
    caption: "Figure 36. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz Single-Ended"
    type: "characteristic_curve"
    page: 20
  - file: "adaq4224/figures/adaq4224-f039.png"
    caption: "Figure 37. THD vs. Input Frequency, Various Amplitudes, G = 1/3"
    type: "characteristic_curve"
    page: 21
  - file: "adaq4224/figures/adaq4224-f040.png"
    caption: "Figure 38. THD vs. Input Frequency, Various Amplitudes, G = 5/9"
    type: "characteristic_curve"
    page: 21
  - file: "adaq4224/figures/adaq4224-f041.png"
    caption: "Figure 39. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 5 V"
    type: "characteristic_curve"
    page: 21
  - file: "adaq4224/figures/adaq4224-f042.png"
    caption: "Figure 40. THD vs. Input Frequency, Various Amplitudes, G = 20/9"
    type: "characteristic_curve"
    page: 21
  - file: "adaq4224/figures/adaq4224-f043.png"
    caption: "Figure 41. THD vs. Input Frequency, Various Amplitudes, G = 20/3"
    type: "characteristic_curve"
    page: 21
  - file: "adaq4224/figures/adaq4224-f044.png"
    caption: "Figure 42. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 21
  - file: "adaq4224/figures/adaq4224-f045.png"
    caption: "Figure 43. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V"
    type: "characteristic_curve"
    page: 22
  - file: "adaq4224/figures/adaq4224-f046.png"
    caption: "Figure 44. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V"
    type: "characteristic_curve"
    page: 22
  - file: "adaq4224/figures/adaq4224-f047.png"
    caption: "Figure 45. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V"
    type: "characteristic_curve"
    page: 22
  - file: "adaq4224/figures/adaq4224-f048.png"
    caption: "Figure 46. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 22
  - file: "adaq4224/figures/adaq4224-f049.png"
    caption: "Figure 47. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 22
  - file: "adaq4224/figures/adaq4224-f050.png"
    caption: "Figure 48. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 22
  - file: "adaq4224/figures/adaq4224-f051.png"
    caption: "Figure 49. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V"
    type: "characteristic_curve"
    page: 23
  - file: "adaq4224/figures/adaq4224-f052.png"
    caption: "Figure 50. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 5 V"
    type: "characteristic_curve"
    page: 23
  - file: "adaq4224/figures/adaq4224-f053.png"
    caption: "Figure 51. Transition Noise vs. Temperature, REFIN = 5 V"
    type: "characteristic_curve"
    page: 23
  - file: "adaq4224/figures/adaq4224-f054.png"
    caption: "Figure 52. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 23
  - file: "adaq4224/figures/adaq4224-f055.png"
    caption: "Figure 53. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 23
  - file: "adaq4224/figures/adaq4224-f056.png"
    caption: "Figure 54. Transition Noise vs. Temperature, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 23
  - file: "adaq4224/figures/adaq4224-f057.png"
    caption: "Figure 55. RMS Noise vs. Temperature, REFIN = 5 V"
    type: "characteristic_curve"
    page: 24
  - file: "adaq4224/figures/adaq4224-f058.png"
    caption: "Figure 56. Offset Error vs. Temperature"
    type: "characteristic_curve"
    page: 24
  - file: "adaq4224/figures/adaq4224-f059.png"
    caption: "Figure 57. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 5 V"
    type: "characteristic_curve"
    page: 24
  - file: "adaq4224/figures/adaq4224-f060.png"
    caption: "Figure 58. RMS Noise vs. Temperature, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 24
  - file: "adaq4224/figures/adaq4224-f061.png"
    caption: "Figure 59. Gain Error vs. Temperature"
    type: "characteristic_curve"
    page: 24
  - file: "adaq4224/figures/adaq4224-f062.png"
    caption: "Figure 60. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 24
  - file: "adaq4224/figures/adaq4224-f063.png"
    caption: "Figure 61. Low Frequency Noise (Output Data Rate = 256 SPS After Averaging Blocks of 4096 Samples), REFIN = 5 V"
    type: "characteristic_curve"
    page: 25
  - file: "adaq4224/figures/adaq4224-f064.png"
    caption: "Figure 62. AC CMRR vs. Input Frequency, REFIN = 5 V"
    type: "characteristic_curve"
    page: 25
  - file: "adaq4224/figures/adaq4224-f065.png"
    caption: "Figure 63. Input Current vs. Input Voltage across Temperature"
    type: "characteristic_curve"
    page: 25
  - file: "adaq4224/figures/adaq4224-f066.png"
    caption: "Figure 64. Low Frequency Noise (Output Data Rate = 256 SPS After Averaging Blocks of 4096 Samples), REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 25
  - file: "adaq4224/figures/adaq4224-f067.png"
    caption: "Figure 65. AC CMRR vs. Input Frequency, REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 25
  - file: "adaq4224/figures/adaq4224-f068.png"
    caption: "Figure 66. Input Bias Current vs. Temperature"
    type: "characteristic_curve"
    page: 25
  - file: "adaq4224/figures/adaq4224-f069.png"
    caption: "Figure 67. Reference Buffer Offset vs. Temperature"
    type: "characteristic_curve"
    page: 26
  - file: "adaq4224/figures/adaq4224-f070.png"
    caption: "Figure 68. Operating Current PGA and FDA vs. Temperature"
    type: "characteristic_curve"
    page: 26
  - file: "adaq4224/figures/adaq4224-f071.png"
    caption: "Figure 69. Operating Current PGA and FDA vs. Sample Rate"
    type: "characteristic_curve"
    page: 26
  - file: "adaq4224/figures/adaq4224-f072.png"
    caption: "Figure 70. REFIN Current Normal Operation vs. Temperature"
    type: "characteristic_curve"
    page: 26
  - file: "adaq4224/figures/adaq4224-f073.png"
    caption: "Figure 71. Operating Current ADC vs. Temperature"
    type: "characteristic_curve"
    page: 26
  - file: "adaq4224/figures/adaq4224-f074.png"
    caption: "Figure 72. Operating Current ADC vs. Sample Rate"
    type: "characteristic_curve"
    page: 26
  - file: "adaq4224/figures/adaq4224-f075.png"
    caption: "Figure 73. Standby Current PGA and FDA vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "adaq4224/figures/adaq4224-f076.png"
    caption: "Figure 74. Shutdown Current vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "adaq4224/figures/adaq4224-f077.png"
    caption: "Figure 75. Power Dissipation vs. Throughput"
    type: "characteristic_curve"
    page: 27
  - file: "adaq4224/figures/adaq4224-f078.png"
    caption: "Figure 76. Standby Current ADC vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "adaq4224/figures/adaq4224-f079.png"
    caption: "Figure 77. VIO Operating Current vs. Sample Rate"
    type: "characteristic_curve"
    page: 27
  - file: "adaq4224/figures/adaq4224-f080.png"
    caption: "Figure 78. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 5 V, All Gains"
    type: "characteristic_curve"
    page: 27
  - file: "adaq4224/figures/adaq4224-f081.png"
    caption: "Figure 79. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 4.096 V, All Gains"
    type: "characteristic_curve"
    page: 28
  - file: "adaq4224/figures/adaq4224-f082.png"
    caption: "Figure 80. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Positive, All Gains"
    type: "characteristic_curve"
    page: 28
  - file: "adaq4224/figures/adaq4224-f083.png"
    caption: "Figure 81. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Negative, All Gains"
    type: "characteristic_curve"
    page: 28
  - file: "adaq4224/figures/adaq4224-f084.png"
    caption: "Figure 82. AC PSRR vs. Frequency, VDD_FDA"
    type: "characteristic_curve"
    page: 28
  - file: "adaq4224/figures/adaq4224-f085.png"
    caption: "Figure 83. AC PSRR vs. Frequency, V_{DDH}"
    type: "characteristic_curve"
    page: 28
  - file: "adaq4224/figures/adaq4224-f086.png"
    caption: "Figure 84. AC PSRR vs. Frequency, VDD_5V"
    type: "characteristic_curve"
    page: 28
  - file: "adaq4224/figures/adaq4224-f087.png"
    caption: "Figure 85. AC PSRR vs. Frequency, VSS_FDA"
    type: "characteristic_curve"
    page: 29
  - file: "adaq4224/figures/adaq4224-f088.png"
    caption: "Figure 86. AC PSRR vs. Frequency, V_{SSH}"
    type: "characteristic_curve"
    page: 29
  - file: "adaq4224/figures/adaq4224-f089.png"
    caption: "Figure 87. FFT, Grounded Inputs REFIN = 5 V"
    type: "characteristic_curve"
    page: 29
  - file: "adaq4224/figures/adaq4224-f090.png"
    caption: "Figure 88. FFT, Grounded Inputs REFIN = 4.096 V"
    type: "characteristic_curve"
    page: 29
  - file: "adaq4224/figures/adaq4224-f091.png"
    caption: "Figure 89. Output Overdrive Recovery, IN = 1 kHz"
    type: "characteristic_curve"
    page: 29
  - file: "adaq4224/figures/adaq4224-f092.png"
    caption: "Figure 90. Long Term Drift, Offset Error RTO, G = 1/3"
    type: "characteristic_curve"
    page: 29
  - file: "adaq4224/figures/adaq4224-f093.png"
    caption: "Figure 91. Long Term Drift, Offset Error RTO, G = 5/9"
    type: "characteristic_curve"
    page: 30
  - file: "adaq4224/figures/adaq4224-f094.png"
    caption: "Figure 92. Long Term Drift, Offset Error RTO, G = 20/9"
    type: "characteristic_curve"
    page: 30
  - file: "adaq4224/figures/adaq4224-f095.png"
    caption: "Figure 93. Long Term Drift, Offset Error RTO, G = 20/3"
    type: "characteristic_curve"
    page: 30
  - file: "adaq4224/figures/adaq4224-f096.png"
    caption: "Figure 94. AAF Frequency Response"
    type: "characteristic_curve"
    page: 30
  - file: "adaq4224/figures/adaq4224-f097.png"
    caption: "Figure 95. ADAQ4224 Functional Block Diagram"
    type: "block_diagram"
    page: 33
  - file: "adaq4224/figures/adaq4224-f098.png"
    caption: "Figure 96. ADC Ideal Transfer Function for the Differential Output Codes (FSR Is Full-Scale Range)"
    type: "other"
    page: 34
  - file: "adaq4224/figures/adaq4224-f099.png"
    caption: "Figure 97. Frequency Response Examples for the Block Averaging Filter"
    type: "characteristic_curve"
    page: 35
  - file: "adaq4224/figures/adaq4224-f100.png"
    caption: "Figure 98. Summary of Selectable Output Sample Formats"
    type: "other"
    page: 35
  - file: "adaq4224/figures/adaq4224-f101.png"
    caption: "Figure 99. Functional Block Diagram of a Fully Isolated Data-Acquisition System"
    type: "application_circuit"
    page: 39
  - file: "adaq4224/figures/adaq4224-f102.png"
    caption: "Figure 100. Differential Input Configuration with G = 1/3 V/V"
    type: "application_circuit"
    page: 40
  - file: "adaq4224/figures/adaq4224-f103.png"
    caption: "Figure 101. Differential Input Configuration with G = 5/9 V/V"
    type: "application_circuit"
    page: 40
  - file: "adaq4224/figures/adaq4224-f104.png"
    caption: "Figure 102. Differential Input Configuration with G = 20/9 V/V"
    type: "application_circuit"
    page: 41
  - file: "adaq4224/figures/adaq4224-f105.png"
    caption: "Figure 103. Differential Input Configuration with G = 20/3 V/V"
    type: "application_circuit"
    page: 41
  - file: "adaq4224/figures/adaq4224-f106.png"
    caption: "Figure 104. Single-Ended Input Configuration with G = 1/3 V/V"
    type: "application_circuit"
    page: 42
  - file: "adaq4224/figures/adaq4224-f107.png"
    caption: "Figure 105. Single-Ended Input Configuration with G = 5/9 V/V"
    type: "application_circuit"
    page: 42
  - file: "adaq4224/figures/adaq4224-f108.png"
    caption: "Figure 106. Single-Ended Input Configuration with G = 20/9 V/V"
    type: "application_circuit"
    page: 43
  - file: "adaq4224/figures/adaq4224-f109.png"
    caption: "Figure 107. Single-Ended Input Configuration with G = 20/3 V/V"
    type: "application_circuit"
    page: 43
  - file: "adaq4224/figures/adaq4224-f111.png"
    caption: "Figure 110. Power-On Reset (POR) Timing"
    type: "timing_diagram"
    page: 45
  - file: "adaq4224/figures/adaq4224-f112.png"
    caption: "Figure 111. Power Supply Sequence"
    type: "timing_diagram"
    page: 45
  - file: "adaq4224/figures/adaq4224-f113.png"
    caption: "Figure 112. VDD_5V Minimum and Maximum Values for REFIN"
    type: "characteristic_curve"
    page: 45
  - file: "adaq4224/figures/adaq4224-f114.png"
    caption: "Figure 113. ADAQ4224 Multilane SPI"
    type: "block_diagram"
    page: 47
  - file: "adaq4224/figures/adaq4224-f115.png"
    caption: "Figure 114. Stream Mode Bulk Register Readback Operation"
    type: "timing_diagram"
    page: 48
  - file: "adaq4224/figures/adaq4224-f116.png"
    caption: "Figure 115. Example Timing for Data Transfer Zones"
    type: "timing_diagram"
    page: 49
  - file: "adaq4224/figures/adaq4224-f117.png"
    caption: "Figure 116. Typical Sample Cycle for SPI Clocking Mode"
    type: "timing_diagram"
    page: 50
  - file: "adaq4224/figures/adaq4224-f118.png"
    caption: "Figure 117. Echo Clock Mode Signal Path Diagram"
    type: "block_diagram"
    page: 51
  - file: "adaq4224/figures/adaq4224-f119.png"
    caption: "Figure 118. Host Clock Mode Signal Path Example"
    type: "block_diagram"
    page: 51
  - file: "adaq4224/figures/adaq4224-f120.png"
    caption: "Figure 119. Basic Single Sample Conversion Cycle"
    type: "timing_diagram"
    page: 53
  - file: "adaq4224/figures/adaq4224-f121.png"
    caption: "Figure 120. Example Conversion Cycle for Averaging Mode"
    type: "timing_diagram"
    page: 53
  - file: "adaq4224/figures/adaq4224-f122.png"
    caption: "Figure 121. Example of Different Zones in Averaging Mode (64 Samples Averaged)"
    type: "timing_diagram"
    page: 54
  - file: "adaq4224/figures/adaq4224-f123.png"
    caption: "Figure 122. Example of Zone 2 in Averaging Mode (1 Bit per Sample)"
    type: "timing_diagram"
    page: 54
  - file: "adaq4224/figures/adaq4224-f124.png"
    caption: "Figure 123. Example of Zone 2 in Averaging Mode (N Bits per Cycle)"
    type: "timing_diagram"
    page: 54
  - file: "adaq4224/figures/adaq4224-f125.png"
    caption: "Figure 124. 2-Lane Mode, SDR Timing Diagram"
    type: "timing_diagram"
    page: 55
  - file: "adaq4224/figures/adaq4224-f126.png"
    caption: "Figure 125. 4-Lane, SDR Timing Diagram"
    type: "timing_diagram"
    page: 56
  - file: "adaq4224/figures/adaq4224-f127.png"
    caption: ""
    type: "register_bitfield"
    page: 60
  - file: "adaq4224/figures/adaq4224-f128.png"
    caption: ""
    type: "register_bitfield"
    page: 60
  - file: "adaq4224/figures/adaq4224-f129.png"
    caption: ""
    type: "register_bitfield"
    page: 61
  - file: "adaq4224/figures/adaq4224-f130.png"
    caption: ""
    type: "register_bitfield"
    page: 61
  - file: "adaq4224/figures/adaq4224-f131.png"
    caption: ""
    type: "register_bitfield"
    page: 61
  - file: "adaq4224/figures/adaq4224-f132.png"
    caption: ""
    type: "register_bitfield"
    page: 61
  - file: "adaq4224/figures/adaq4224-f133.png"
    caption: ""
    type: "register_bitfield"
    page: 62
  - file: "adaq4224/figures/adaq4224-f134.png"
    caption: ""
    type: "register_bitfield"
    page: 62
  - file: "adaq4224/figures/adaq4224-f135.png"
    caption: ""
    type: "register_bitfield"
    page: 62
  - file: "adaq4224/figures/adaq4224-f136.png"
    caption: ""
    type: "register_bitfield"
    page: 63
  - file: "adaq4224/figures/adaq4224-f137.png"
    caption: ""
    type: "register_bitfield"
    page: 63
  - file: "adaq4224/figures/adaq4224-f138.png"
    caption: ""
    type: "register_bitfield"
    page: 63
  - file: "adaq4224/figures/adaq4224-f140.png"
    caption: ""
    type: "register_bitfield"
    page: 64
  - file: "adaq4224/figures/adaq4224-f141.png"
    caption: ""
    type: "register_bitfield"
    page: 64
  - file: "adaq4224/figures/adaq4224-f142.png"
    caption: ""
    type: "register_bitfield"
    page: 64
  - file: "adaq4224/figures/adaq4224-f143.png"
    caption: ""
    type: "register_bitfield"
    page: 65
  - file: "adaq4224/figures/adaq4224-f144.png"
    caption: ""
    type: "register_bitfield"
    page: 65
  - file: "adaq4224/figures/adaq4224-f145.png"
    caption: ""
    type: "register_bitfield"
    page: 65
  - file: "adaq4224/figures/adaq4224-f146.png"
    caption: ""
    type: "register_bitfield"
    page: 65
  - file: "adaq4224/figures/adaq4224-f147.png"
    caption: ""
    type: "register_bitfield"
    page: 66
  - file: "adaq4224/figures/adaq4224-f148.png"
    caption: ""
    type: "register_bitfield"
    page: 66
  - file: "adaq4224/figures/adaq4224-f149.png"
    caption: ""
    type: "register_bitfield"
    page: 67
  - file: "adaq4224/figures/adaq4224-f150.png"
    caption: ""
    type: "register_bitfield"
    page: 67
  - file: "adaq4224/figures/adaq4224-f151.png"
    caption: ""
    type: "register_bitfield"
    page: 67
  - file: "adaq4224/figures/adaq4224-f152.png"
    caption: ""
    type: "register_bitfield"
    page: 67
  - file: "adaq4224/figures/adaq4224-f153.png"
    caption: ""
    type: "register_bitfield"
    page: 68
  - file: "adaq4224/figures/adaq4224-f154.png"
    caption: ""
    type: "register_bitfield"
    page: 68
  - file: "adaq4224/figures/adaq4224-f155.png"
    caption: ""
    type: "register_bitfield"
    page: 68
  - file: "adaq4224/figures/adaq4224-f156.png"
    caption: "Figure 126. 178-Ball Chip-Scale Package, Ball Grid Array [CSP_BGA] (BC-178-2) Dimensions Shown in millimeters"
    type: "other"
    page: 71
  - file: "adaq4224/figures/adaq4224-eq01.png"
    caption: "Equation as printed (p. 31)"
    type: equation
    page: 31
  - file: "adaq4224/figures/adaq4224-eq02.png"
    caption: "Equation as printed (p. 31)"
    type: equation
    page: 31
  - file: "adaq4224/figures/adaq4224-eq03.png"
    caption: "Equation as printed (p. 53)"
    type: equation
    page: 53
  - file: "adaq4224/figures/adaq4224-eq04.png"
    caption: "Equation as printed (p. 53)"
    type: equation
    page: 53
  - file: "adaq4224/figures/adaq4224-eq05.png"
    caption: "Equation as printed (p. 53)"
    type: equation
    page: 53
curves:
  - file: "adaq4224/curves/aaf-frequency-response.csv"
    caption: "Figure 94. AAF Frequency Response"
    figure: "adaq4224/figures/adaq4224-f096.png"
    page: 30
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "IN = 100 mV p-p"
  - file: "adaq4224/curves/ac-cmrr-vs-input-frequency-refin-4-096-v.csv"
    caption: "Figure 65. AC CMRR vs. Input Frequency, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f067.png"
    page: 25
    x_unit: "MHz"
    y_unit: "dB"
  - file: "adaq4224/curves/ac-cmrr-vs-input-frequency-refin-5-v.csv"
    caption: "Figure 62. AC CMRR vs. Input Frequency, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f064.png"
    page: 25
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "REFIN = 5 V"
  - file: "adaq4224/curves/ac-psrr-vs-frequency-v-ddh.csv"
    caption: "Figure 83. AC PSRR vs. Frequency, V_{DDH}"
    figure: "adaq4224/figures/adaq4224-f085.png"
    page: 28
    x_unit: "Hz"
    y_unit: "dB"
  - file: "adaq4224/curves/ac-psrr-vs-frequency-v-ssh.csv"
    caption: "Figure 86. AC PSRR vs. Frequency, V_{SSH}"
    figure: "adaq4224/figures/adaq4224-f088.png"
    page: 29
    x_unit: "Hz"
    y_unit: "dB"
  - file: "adaq4224/curves/ac-psrr-vs-frequency-vdd-5v.csv"
    caption: "Figure 84. AC PSRR vs. Frequency, VDD_5V"
    figure: "adaq4224/figures/adaq4224-f086.png"
    page: 28
    x_unit: "Hz"
    y_unit: "dB"
  - file: "adaq4224/curves/ac-psrr-vs-frequency-vdd-fda.csv"
    caption: "Figure 82. AC PSRR vs. Frequency, VDD_FDA"
    figure: "adaq4224/figures/adaq4224-f084.png"
    page: 28
    x_unit: "Hz"
    y_unit: "dB"
  - file: "adaq4224/curves/ac-psrr-vs-frequency-vss-fda.csv"
    caption: "Figure 85. AC PSRR vs. Frequency, VSS_FDA"
    figure: "adaq4224/figures/adaq4224-f087.png"
    page: 29
    x_unit: "Hz"
    y_unit: "dB"
  - file: "adaq4224/curves/code-histogram-for-shorted-inputs-refin-4-096-v.csv"
    caption: "Figure 23. Code Histogram for Shorted Inputs, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f025.png"
    page: 18
    x_unit: "CODES"
    y_unit: "k"
    conditions: "NORMALIZED 1048575 SAMPLES"
  - file: "adaq4224/curves/code-histogram-for-shorted-inputs-refin-5-v.csv"
    caption: "Figure 20. Code Histogram for Shorted Inputs, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f022.png"
    page: 18
    x_unit: "CODES"
    y_unit: "G = 20/3; σ = 44.3"
    conditions: "NORMALIZED 1048575 SAMPLES"
  - file: "adaq4224/curves/dynamic-range-vs-number-of-averages-input-60-dbfs-refin-4-096-v.csv"
    caption: "Figure 60. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f062.png"
    page: 24
    x_unit: "samples"
    y_unit: "dB"
  - file: "adaq4224/curves/dynamic-range-vs-number-of-averages-input-60-dbfs-refin-5-v.csv"
    caption: "Figure 57. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f059.png"
    page: 24
    x_unit: "samples"
    y_unit: "dB"
  - file: "adaq4224/curves/frequency-response-examples-for-the-block-averaging-filter.csv"
    caption: "Figure 97. Frequency Response Examples for the Block Averaging Filter"
    figure: "adaq4224/figures/adaq4224-f099.png"
    page: 35
    x_unit: "f_{IN}/f_{S}"
    y_unit: "dB"
  - file: "adaq4224/curves/gain-error-vs-temperature.csv"
    caption: "Figure 59. Gain Error vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f061.png"
    page: 24
    x_unit: "°C"
    y_unit: "%FS"
  - file: "adaq4224/curves/inl-error-vs-output-code-across-temperature-g-1-3.csv"
    caption: "Figure 15. INL Error vs. Output Code across Temperature, G = 1/3"
    figure: "adaq4224/figures/adaq4224-f017.png"
    page: 17
    x_unit: "M"
    y_unit: "ppm"
    conditions: "REFIN = 5V; G =1/3"
  - file: "adaq4224/curves/inl-error-vs-output-code-across-temperature-g-20-3.csv"
    caption: "Figure 22. INL Error vs. Output Code across Temperature, G = 20/3"
    figure: "adaq4224/figures/adaq4224-f024.png"
    page: 18
    x_unit: "M"
    y_unit: "ppm"
    conditions: "REFIN = 5V; G =20/3"
  - file: "adaq4224/curves/inl-error-vs-output-code-across-temperature-g-20-9.csv"
    caption: "Figure 19. INL Error vs. Output Code across Temperature, G = 20/9"
    figure: "adaq4224/figures/adaq4224-f021.png"
    page: 18
    x_unit: "M"
    y_unit: "ppm"
    conditions: "REFIN = 5V; G =20/9"
  - file: "adaq4224/curves/inl-error-vs-output-code-across-temperature-g-5-9.csv"
    caption: "Figure 18. INL Error vs. Output Code across Temperature, G = 5/9"
    figure: "adaq4224/figures/adaq4224-f020.png"
    page: 17
    x_unit: "M (output codes)"
    y_unit: "ppm"
    conditions: "REFIN = 5V; G =5/9"
  - file: "adaq4224/curves/inl-error-vs-output-code-differential-input-refin-4-096-v.csv"
    caption: "Figure 16. INL Error vs. Output Code, Differential Input, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f018.png"
    page: 17
    x_unit: "M"
    y_unit: "ppm"
    conditions: "REFIN = 4.096V; T_{A} = 25°C"
  - file: "adaq4224/curves/inl-error-vs-output-code-differential-input-refin-5-v.csv"
    caption: "Figure 13. INL Error vs. Output Code, Differential Input, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f015.png"
    page: 17
    x_unit: "M (output codes)"
    y_unit: "ppm"
    conditions: "REFIN = 5V; TA = 25°C"
  - file: "adaq4224/curves/inl-error-vs-output-code-single-ended-input-refin-4-096-v.csv"
    caption: "Figure 17. INL Error vs. Output Code, Single-Ended Input, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f019.png"
    page: 17
    x_unit: "M"
    y_unit: "ppm"
    conditions: "REFIN = 4.096V; TA = 25°C"
  - file: "adaq4224/curves/inl-error-vs-output-code-single-ended-input-refin-5-v.csv"
    caption: "Figure 14. INL Error vs. Output Code, Single-Ended Input, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f016.png"
    page: 17
    x_unit: "M"
    y_unit: "ppm"
    conditions: "REFIN = 5V; TA = 25°C"
  - file: "adaq4224/curves/input-bias-current-vs-temperature.csv"
    caption: "Figure 66. Input Bias Current vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f068.png"
    page: 25
    x_unit: "°C"
    y_unit: "pA"
  - file: "adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-refin-4-096-v-all-gains.csv"
    caption: "Figure 79. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 4.096 V, All Gains"
    figure: "adaq4224/figures/adaq4224-f081.png"
    page: 28
    x_unit: "V"
    y_unit: "V"
    conditions: "VDDH = 18V, VSSH = -18V, VDD_FDA = 5.0V, VSS_FDA = 0V, REF = 4.096V"
  - file: "adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-refin-5-v-all-gains.csv"
    caption: "Figure 78. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 5 V, All Gains"
    figure: "adaq4224/figures/adaq4224-f080.png"
    page: 27
    x_unit: "V"
    y_unit: "V"
    conditions: "VDDH = 18V, VSSH = -18V, VDD_FDA = 5.4V, VSS_FDA = -1V, REF = 5V"
  - file: "adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-vin-negative-all-gains.csv"
    caption: "Figure 81. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Negative, All Gains"
    figure: "adaq4224/figures/adaq4224-f083.png"
    page: 28
    x_unit: "V"
    y_unit: "V"
    conditions: "VDDH = 5.4V, VSSH = -32V, VDD_FDA = 5.4V, VSS_FDA = -4.6V, REF = 5V"
  - file: "adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-vin-positive-all-gains.csv"
    caption: "Figure 80. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Positive, All Gains"
    figure: "adaq4224/figures/adaq4224-f082.png"
    page: 28
    x_unit: "V"
    y_unit: "V"
    conditions: "VDDH = 32V, VSSH = -5.4V, VDD_FDA = 9V, VSS_FDA = -1V, REF = 5V"
  - file: "adaq4224/curves/input-current-vs-input-voltage-across-temperature.csv"
    caption: "Figure 63. Input Current vs. Input Voltage across Temperature"
    figure: "adaq4224/figures/adaq4224-f065.png"
    page: 25
    x_unit: "V"
    y_unit: "pA"
  - file: "adaq4224/curves/offset-error-vs-temperature.csv"
    caption: "Figure 56. Offset Error vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f058.png"
    page: 24
    x_unit: "°C"
    y_unit: "µV"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/operating-current-adc-vs-sample-rate.csv"
    caption: "Figure 72. Operating Current ADC vs. Sample Rate"
    figure: "adaq4224/figures/adaq4224-f074.png"
    page: 26
    x_unit: "MSPS"
    y_unit: "mA"
  - file: "adaq4224/curves/operating-current-adc-vs-temperature.csv"
    caption: "Figure 71. Operating Current ADC vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f073.png"
    page: 26
    x_unit: "°C"
    y_unit: "mA"
  - file: "adaq4224/curves/operating-current-pga-and-fda-vs-sample-rate.csv"
    caption: "Figure 69. Operating Current PGA and FDA vs. Sample Rate"
    figure: "adaq4224/figures/adaq4224-f071.png"
    page: 26
    x_unit: "MSPS"
    y_unit: "mA"
  - file: "adaq4224/curves/operating-current-pga-and-fda-vs-temperature.csv"
    caption: "Figure 68. Operating Current PGA and FDA vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f070.png"
    page: 26
    x_unit: "°C"
    y_unit: "mA"
  - file: "adaq4224/curves/power-dissipation-vs-throughput.csv"
    caption: "Figure 75. Power Dissipation vs. Throughput"
    figure: "adaq4224/figures/adaq4224-f077.png"
    page: 27
    x_unit: "MSPS"
    y_unit: "mW"
  - file: "adaq4224/curves/reference-buffer-offset-vs-temperature.csv"
    caption: "Figure 67. Reference Buffer Offset vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f069.png"
    page: 26
    x_unit: "°C"
    y_unit: "µV"
  - file: "adaq4224/curves/refin-current-normal-operation-vs-temperature.csv"
    caption: "Figure 70. REFIN Current Normal Operation vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f072.png"
    page: 26
    x_unit: "°C"
    y_unit: "µA"
  - file: "adaq4224/curves/rms-noise-vs-temperature-refin-4-096-v.csv"
    caption: "Figure 58. RMS Noise vs. Temperature, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f060.png"
    page: 24
    x_unit: "°C"
    y_unit: "µV"
  - file: "adaq4224/curves/rms-noise-vs-temperature-refin-5-v.csv"
    caption: "Figure 55. RMS Noise vs. Temperature, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f057.png"
    page: 24
    x_unit: "°C"
    y_unit: "µV"
    conditions: "REFIN = 5 V"
  - file: "adaq4224/curves/sfdr-vs-input-frequency-0-5-dbfs-refin-4-096-v.csv"
    caption: "Figure 42. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f044.png"
    page: 21
    x_unit: "kHz"
    y_unit: "dBc"
    conditions: "REFIN = 4.096V"
  - file: "adaq4224/curves/sfdr-vs-input-frequency-0-5-dbfs-refin-5-v.csv"
    caption: "Figure 39. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f041.png"
    page: 21
    x_unit: "kHz"
    y_unit: "dBc"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/sfdr-vs-temperature-f-in-1-khz-refin-4-096-v.csv"
    caption: "Figure 53. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f055.png"
    page: 23
  - file: "adaq4224/curves/sfdr-vs-temperature-f-in-1-khz-refin-5-v.csv"
    caption: "Figure 50. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f052.png"
    page: 23
    x_unit: "°C"
    y_unit: "dBc"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/shutdown-current-vs-temperature.csv"
    caption: "Figure 74. Shutdown Current vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f076.png"
    page: 27
    x_unit: "°C"
    y_unit: "µA"
  - file: "adaq4224/curves/snr-sinad-vs-input-amplitude-at-f-in-1-khz.csv"
    caption: "Figure 31. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz"
    figure: "adaq4224/figures/adaq4224-f033.png"
    page: 20
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "adaq4224/curves/snr-sinad-vs-input-amplitude-at-f-in-1-khz-refin-4-096-v.csv"
    caption: "Figure 33. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f035.png"
    page: 20
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "adaq4224/curves/snr-sinad-vs-input-amplitude-at-f-in-1-khz-single-ended.csv"
    caption: "Figure 36. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz Single-Ended"
    figure: "adaq4224/figures/adaq4224-f038.png"
    page: 20
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-differential-input-refin-4-096-v.csv"
    caption: "Figure 46. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f048.png"
    page: 22
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "REFIN = 4.096V"
  - file: "adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-differential-input-refin-5-v.csv"
    caption: "Figure 43. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f045.png"
    page: 22
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-single-ended-input-refin-4-096-v.csv"
    caption: "Figure 47. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f049.png"
    page: 22
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "REFIN = 4.096V"
  - file: "adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-single-ended-input-refin-5-v.csv"
    caption: "Figure 44. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f046.png"
    page: 22
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/snr-vs-input-amplitude-at-f-in-100-khz.csv"
    caption: "Figure 35. SNR vs. Input Amplitude at f_{IN} = 100 kHz"
    figure: "adaq4224/figures/adaq4224-f037.png"
    page: 20
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "adaq4224/curves/snr-vs-input-amplitude-at-f-in-20-khz.csv"
    caption: "Figure 32. SNR vs. Input Amplitude at f_{IN} = 20 kHz"
    figure: "adaq4224/figures/adaq4224-f034.png"
    page: 20
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "adaq4224/curves/snr-vs-input-amplitude-at-f-in-50-khz.csv"
    caption: "Figure 34. SNR vs. Input Amplitude at f_{IN} = 50 kHz"
    figure: "adaq4224/figures/adaq4224-f036.png"
    page: 20
  - file: "adaq4224/curves/standby-current-adc-vs-temperature.csv"
    caption: "Figure 76. Standby Current ADC vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f078.png"
    page: 27
    x_unit: "°C"
    y_unit: "µA"
  - file: "adaq4224/curves/standby-current-pga-and-fda-vs-temperature.csv"
    caption: "Figure 73. Standby Current PGA and FDA vs. Temperature"
    figure: "adaq4224/figures/adaq4224-f075.png"
    page: 27
    x_unit: "°C"
    y_unit: "mA"
  - file: "adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-1-3.csv"
    caption: "Figure 37. THD vs. Input Frequency, Various Amplitudes, G = 1/3"
    figure: "adaq4224/figures/adaq4224-f039.png"
    page: 21
    x_unit: "kHz"
    y_unit: "dBc"
    conditions: "G = 1/3 V/V; REFIN = 5V"
  - file: "adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-20-3.csv"
    caption: "Figure 41. THD vs. Input Frequency, Various Amplitudes, G = 20/3"
    figure: "adaq4224/figures/adaq4224-f043.png"
    page: 21
    x_unit: "kHz"
    y_unit: "dBc"
    conditions: "G = 20/3 V/V; REFIN = 5V"
  - file: "adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-20-9.csv"
    caption: "Figure 40. THD vs. Input Frequency, Various Amplitudes, G = 20/9"
    figure: "adaq4224/figures/adaq4224-f042.png"
    page: 21
    x_unit: "kHz"
    y_unit: "dBc"
    conditions: "G = 20/9 V/V; REFIN = 5V"
  - file: "adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-5-9.csv"
    caption: "Figure 38. THD vs. Input Frequency, Various Amplitudes, G = 5/9"
    figure: "adaq4224/figures/adaq4224-f040.png"
    page: 21
    x_unit: "kHz"
    y_unit: "dBc"
    conditions: "G = 5/9 V/V; REFIN = 5V; INPUT = -0.5dBFS, -1dBFS, -3dBFS, -6dBFS, -10dBFS"
  - file: "adaq4224/curves/thd-vs-temperature-f-in-1-khz-differential-input-refin-4-096-v.csv"
    caption: "Figure 48. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f050.png"
    page: 22
    x_unit: "°C"
    y_unit: "dBc"
    conditions: "REFIN = 4.096V"
  - file: "adaq4224/curves/thd-vs-temperature-f-in-1-khz-differential-input-refin-5-v.csv"
    caption: "Figure 45. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f047.png"
    page: 22
    x_unit: "°C"
    y_unit: "dBc"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/thd-vs-temperature-f-in-1-khz-single-ended-input-refin-4-096-v.csv"
    caption: "Figure 52. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f054.png"
    page: 23
  - file: "adaq4224/curves/thd-vs-temperature-f-in-1-khz-single-ended-input-refin-5-v.csv"
    caption: "Figure 49. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f051.png"
    page: 23
    x_unit: "°C"
    y_unit: "dBc"
    conditions: "REFIN = 5V"
  - file: "adaq4224/curves/transition-noise-vs-temperature-refin-4-096-v.csv"
    caption: "Figure 54. Transition Noise vs. Temperature, REFIN = 4.096 V"
    figure: "adaq4224/figures/adaq4224-f056.png"
    page: 23
    x_unit: "°C"
    y_unit: "LSBrms"
    conditions: "REFIN = 4.096 V"
  - file: "adaq4224/curves/transition-noise-vs-temperature-refin-5-v.csv"
    caption: "Figure 51. Transition Noise vs. Temperature, REFIN = 5 V"
    figure: "adaq4224/figures/adaq4224-f053.png"
    page: 23
    x_unit: "°C"
    y_unit: "LSBrms"
  - file: "adaq4224/curves/vdd-5v-minimum-and-maximum-values-for-refin.csv"
    caption: "Figure 112. VDD_5V Minimum and Maximum Values for REFIN"
    figure: "adaq4224/figures/adaq4224-f113.png"
    page: 45
    x_unit: ""
    y_unit: "V"
    conditions: "≥250mV"
  - file: "adaq4224/curves/vio-operating-current-vs-sample-rate.csv"
    caption: "Figure 77. VIO Operating Current vs. Sample Rate"
    figure: "adaq4224/figures/adaq4224-f079.png"
    page: 27
    x_unit: "MSPS"
    y_unit: "mA"
agentforge:
  part_number: "ADAQ4224"
  datasheet_revision: "C"
  repairs: 2
  reading_order: "geometry"
---

![other (p. 1)](adaq4224/figures/adaq4224-f002.png)

# ADAQ4224 — 24-Bit, 2 MSPS, µModule Data-Acquisition Solution

*Datasheet: [ADAQ4224 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/adaq4224.pdf)*

### FEATURES
<!-- page: 1 -->

- High performance
  - Throughput: 2 MSPS, no latency
  - INL: ±1 ppm maximum from -40 °C to 105 °C
  - Total system dynamic range: 128 dB typical
  - SNR: 106.5 dBFS typical, THD: -122 dBc typical
  - Offset error drift: +4.1 µV/°C maximum
  - Gain error drift: +1.50 ppm/°C maximum
- Ease of use features reduce system complexity
  - Second-order, 270 kHz anti-aliasing filter
  - High-Z PGIA gain options: 1/3, 5/9, 20/9, 20/3
  - Flexible external reference voltage: 4.096 V or 5 V
  - Differential Input Voltage ranges, ±REFIN/Gain: ±15 V, ±9 V, ±2.25 V, ±0.75 V
  - Wide input common-mode voltage range: -8 V to +10 V
  - Low input bias current: ±20 pA typical
- High density solution reduces system footprint
  - 14 mm × 9 mm, 0.8 mm pitch, 178-ball CSP BGA
  - 4× footprint reduction vs. equivalent discrete solution
  - On-board reference buffer with an internal VCM generation
- Total power dissipation: 446 mW typical at 2 MSPS
- Electrically isolated, 1.8 V I^{2}C-compatible temperature sensor
- Flexi-SPI digital interface
  - 1, 2, or 4 SDO lanes allows slower SCK
  - Echo clock mode simplifies use of digital isolator
  - Compatible with 1.2 V to 1.8 V logic
  - PGIA gain control (A0, A1) interface
  - Extended sample resolution to 30-bits
  - Overrange and synchronization bits

### APPLICATIONS
<!-- pages: 1-4 -->

- Automatic test equipment
- Machine automation
- Process controls
- Medical and industrial instrumentation
- Digital control loops

### FUNCTIONAL BLOCK DIAGRAM
<!-- page: 1 -->

![Figure 1. ADAQ4224 Functional Block Diagram](adaq4224/figures/adaq4224-f001.png)

*Figure 1. ADAQ4224 Functional Block Diagram*


### TABLE OF CONTENTS

- Features...1
- Applications...1
- Functional Block Diagram...1
- General Description...4
- Specifications...5
  - Timing Specifications...9
- Absolute Maximum Ratings...14
  - Thermal Resistance...14
  - Electrostatic Discharge (ESD) Ratings...14
  - ESD Caution...14
- Pin Configurations and Function Descriptions...15
- Typical Performance Characteristics...17
- Terminology...31
- Theory of Operation...33
  - Overview...33
  - Transfer Function...33
  - Signal Chain Operation...34
  - Digital Sample Processing Features...34
  - Temperature Sensor Operation...35
- Applications Information...39
  - Typical Application Diagram...39
  - Reference Circuitry Design...44
  - ADC Reset...45
  - Power Supplies...45
- Serial Interface...47
  - SPI Signals...47
  - Sample Conversion Timing and Data Transfer...49
  - Clocking Modes...50
  - Data Clocking Requirements and Timing...53
- Layout Guidelines...58
- Registers...59
- Register Details...60
  - Interface Configuration A Register...60
  - Interface Configuration B Register...60
  - Device Configuration Register...61
  - Chip Type Register...61
  - Product ID Low Register...61
  - Product ID High Register...61
  - Chip Grade Register...62
  - Scratch Pad Register...62
  - SPI Revision Register...62
  - Vendor ID Low Register...63
  - Vendor ID High Register...63
  - Stream Mode Register...63
  - Interface Status A Register...63
  - EXIT Configuration Mode Register...64
  - Averaging Mode Register...64
  - Offset Registers...64
  - Gain Registers...65
  - Modes Register...66
  - Internal Oscillator Register...66
  - Output Driver Register...67
  - Test Pattern Registers...67
  - Digital Diagnostics Register...68
  - Digital Errors Register...68
- Temperature Sensor Registers...69
- Temperature Sensor Register Details...70
  - Configuration and Status Register...70
- Outline Dimensions...71
  - Ordering Guide...71
  - Evaluation Boards...71
### REVISION HISTORY
-   2/2026-Rev. B to Rev. C
- Changes to Table 1...5
- Changes to Table 12...15
- Changes to Figure 78 and 79...27
- Added Figure 80 and Figure 81; Renumbered Sequentially...28
- Added Figure 90 to Figure 94...29

- 7/2025-Rev. A to Rev. B
- Changes to Transition Noise Parameter and Noise Spectral Density (NSD) Parameter, Table 1...5
- Changes to Figure 12 and Figure 12 Caption...15
- Changes to Figure 20 and Figure 23...18
- Added Figure 85 and Figure 86; Renumbered Sequentially...29
- Added Least Significant Bit (LSB) Section...31
- Added Transition Noise Section...31
- Change to Transient Response Section...31
- Change to Common-Mode Rejection Ratio (CMRR) Section...31
- 5/2025-Rev. 0 to Rev. A
- Changes to Features Section...1
- Changes to General Description Section...4
- Changes to Table 1...5
- Changes to Figure 12...15
- Changes to Typical Performance Characteristics Section...17
- Added Figure 66; Renumbered Sequentially...25
- Added Figure 80 to Figure 84...28
- Moved Figure 85...29
- Changes to Spurious-Free Dynamic Range (SFDR) Section...31
- Changes to Total Harmonic Distortion (THD) Section...31
- Changes to Signal-to-Noise Ratio (SNR) Section...31
- Changes to Signal-to-Noise-and-Distortion (SINAD) Ratio Section...31
- 9/2024-Revision 0: Initial Version

### GENERAL DESCRIPTION
<!-- pages: 4-5 -->

The ADAQ4224 is a µModule®  precision data acquisition (DAQ) signal chain solution that reduces the development cycle of a precision measurement system by transferring the signal-chain design challenge of component selection, optimization, and layout from the designer to the device. With a guaranteed maximum ±1.0 ppm INL and no missing codes at 24 bits, the ADAQ4224 achieves unparalleled precision performance from -40°C to +105°C.

Using system-in-package (SIP) technology, the ADAQ4224 combines the common signal processing blocks required in a data acquisition solution in a small footprint, 14 mm × 9 mm, 0.8 mm pitch, 178-ball CSP\_BGA package.

The ADAQ4224 integrates the following:

- A low noise, high-bandwidth programmable gain instrumentation amplifier (PGIA).
- A second-order anti-aliasing filter.
- A low-noise, low-distortion, high-bandwidth ADC driver.
- A high precision 24-bit, 2 MSPS successive approximation register (SAR) ADC.
- An electrically isolated, I^{2}C compatible temperature sensor with excellent accuracy of ±1°C maximum.
- A 1.8 V low dropout (LDO) regulator.
- Performance critical passives.

The ADAQ4224 incorporates the critical passive components with superior matching and drift characteristics using Analog Devices, Inc., iPassives®  technology to minimize temperature-dependent error sources and to offer optimized performance. Integrating the critical power supply and reference bypass capacitors reduce sensitivity to the system level board layout. Reducing the solution footprint enables addition of more functions within the system and hence the smaller form factor instruments without sacrificing performance.

The system integration solves many design challenges while the µModule still provides the flexibility of a configurable PGIA: allowing gain or attenuation and supporting the acquisition of differential or single-ended input signal. The fast settling of the PGIA and ADC driver stage and no latency of the SAR ADC provide a unique solution for high channel count, multiplexed signal-chain architectures and control loop applications.

The digital features include Flexi-SPI serial-peripheral interface (SPI), which allow data access by multiple SPI modes as well as offset correction, gain adjustment, and averaging. The digital features reduces the burden on the host processor. A wide-data clocking window, multiple SDO lanes, and optional DDR data clocking reduce the serial clock frequency while operating at full speed of 2 MSPS and make it easier to isolate the DAQ solution, which reduces power dissipation and EMI. The echo clock mode and host clock mode of the ADAQ4224 relax the timing requirements and simplify the use of digital isolators.

The Flexi-SPI, PGIA gain control, and I^{2}C-compatible temperature sensor serial-user interface is compatible with 1.2 V to 1.8 V logic using a separate VIO supply. The ADAQ4224 operation is specified from -40°C to +105°C.

### SPECIFICATIONS
<!-- pages: 5-14 -->
V_{DDH} = 18 V, V_{SSH} = −18 V, VDD_FDA = 5.4 V, VSS_FDA = 0, VDD_5V = 5.4 V, V_{LDO} = 5.4 V, V_{IO} = 1.8 V, V_{DD} = 3.3 V, REFIN = 5 V, sampling
frequency (f_{S}) = 2 MSPS, all gains, and all specifications T_{MIN} to T_{MAX}, unless otherwise noted.

**Table 1. Specifications** ([table-00-p5-spec.csv](adaq4224/tables/table-00-p5-spec.csv), p. 5)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| RESOLUTION |  | 24 |  |  | Bits |
| **DIFFERENTIAL INPUT VOLTAGE RANGE, V_{IN}[^1]** | V_{IN} = ± REFIN/Gain, VSS_FDA = −1 V |  |  |  |  |
| DIFFERENTIAL INPUT VOLTAGE RANGE, V_{IN}[^1] | Gain = 1/3 | −15 |  | +15 | V |
| DIFFERENTIAL INPUT VOLTAGE RANGE, V_{IN}[^1] | Gain = 5/9 | −9 |  | +9 | V |
| DIFFERENTIAL INPUT VOLTAGE RANGE, V_{IN}[^1] | Gain = 20/9 | −2.25 |  | +2.25 | V |
| DIFFERENTIAL INPUT VOLTAGE RANGE, V_{IN}[^1] | Gain = 20/3 | −0.75 |  | +0.75 | V |
| Analog Front-End Gain (G) | A0 = low, A1 = low |  | 1/3 |  | V/V |
| Analog Front-End Gain (G) | A0 = high, A1 = low |  | 5/9 |  | V/V |
| Analog Front-End Gain (G) | A0 = low, A1 = high |  | 20/9 |  | V/V |
| Analog Front-End Gain (G) | A0 = high, A1 = high |  | 20/3 |  | V/V |
| Input Common-Mode Voltage Range | All gains | −8 |  | +10 | V |
| Common-Mode Rejection Ratio (CMRR) | DC |  | 95 |  | dB |
| Input Bias Current | INP, INN, T_{A} = +25°C |  | ±20 | ±100 | pA |
| Input Bias Current | T_{A} = −40°C to +60°C |  |  | ±350 | pA |
| Input Bias Current | T_{A} = −40°C to +105°C |  |  | ±3.5 | nA |
| Input Offset Current | T_{A} = +25°C |  | ±3 | ±25 | pA |
| Input Offset Current | T_{A} = −40°C to +60°C |  |  | ±30 | pA |
| Input Offset Current | T_{A} = −40°C to +105°C |  |  | ±250 | pA |
| Input Resistance | INP, INN |  | 10^{12} |  | Ω |
| Input Capacitance | INP, INN |  | 13.8 |  | pF |
| **THROUGHPUT** |  |  |  |  |  |
| Complete Cycle |  | 500 |  |  | ns |
| Conversion Time |  | 264 | 282 | 300 | ns |
| Acquisition Phase[^2] |  | 244 | 260 | 275 | ns |
| Throughput Rate |  | 0 |  | 2 | MSPS |
| **DC ACCURACY** |  |  |  |  |  |
| No Missing Codes |  | 24 |  |  | Bits |
| Integral Nonlinearity Error (INL)[^3][^4] | All gains. VSS_FDA = 0 V | −1 | ±0.4 | +1 | ppm |
| Differential Nonlinearity Error (DNL)[^3] | All gains |  | ±0.5 |  | LSB |
| Transition Noise | G = 1/3 |  | 24.44 |  | LSBrms |
| Transition Noise | G = 5/9 |  | 25.01 |  | LSBrms |
| Transition Noise | G = 20/9 |  | 29.72 |  | LSBrms |
| Transition Noise | G = 20/3 |  | 44.48 |  | LSBrms |
| Offset Error | G = 1/3 | −0.8 | ±0.10 | +0.8 | mV |
| Offset Error | G = 5/9 | −0.8 | ±0.11 | +0.8 | mV |
| Offset Error | G = 20/9 | −0.95 | ±0.13 | +0.95 | mV |
| Offset Error | G = 20/3 | −1.4 | ±0.23 | +1.4 | mV |
| **Offset Error Drift** | T= −40°C to +105°C, End point method |  |  |  |  |
| Offset Error Drift | G = 1/3, 5/9, 20/9 | −7.1 | ±1.7 | +4.1 | µV/°C |
| Offset Error Drift | G = 20/3 | −9.2 | ±1.2 | +6.8 | µV/°C |
| Gain Error | REFIN = 5 V | −0.06 | ±0.006 | +0.06 | %FS |
| **Gain Error Drift** | T = −40°C to +105°C, End point method |  |  |  |  |
|  | All gains | −1.25 | 0.1 | 1.50 | ppm/°C |
| Power-Supply Rejection Ratio (PSRR) | V_{DDH} = +15 V to +18 V step |  | 122 |  | dB |
| Power-Supply Rejection Ratio (PSRR) | V_{SSH} = −15 V to −18 V step |  | 129 |  | dB |
| Power-Supply Rejection Ratio (PSRR) | VDD_FDA = +4.5 V to +5.5 V step |  | 109 |  | dB |
| Power-Supply Rejection Ratio (PSRR) | VSS_FDA = 0 V to −1 V step |  | 104 |  | dB |
| Power-Supply Rejection Ratio (PSRR) | VDD_5V = +5.3 V to +5.5 V step |  | 109 |  | dB |
| Power-Supply Rejection Ratio (PSRR) | V_{LDO} = +5.3 V to +5.5 V step |  | 113 |  | dB |
| Low Frequency Noise[^5] | Referred to input, bandwidth = 0.1 Hz to 10 Hz, all gains |  | 6 |  | µV p-p |
| **AC ACCURACY** |  |  |  |  |  |
| Dynamic Range | G = 1/3 |  | 107.7 |  | dB |
| Dynamic Range | G = 5/9 |  | 107.5 |  | dB |
| Dynamic Range | G = 20/9 |  | 106 |  | dB |
| Dynamic Range | G = 20/3 |  | 102.5 |  | dB |
| Total-System Dynamic Range |  |  | 128 |  | dB |
| Input Voltage Noise Density | f_{IN} = 1 kHz |  |  |  |  |
| Input Voltage Noise Density | G = 1/3 |  | 43.7 |  | nV/√Hz |
| Input Voltage Noise Density | G = 5/9 |  | 26.8 |  | nV/√Hz |
| Input Voltage Noise Density | G = 20/9 |  | 8 |  | nV/√Hz |
| Input Voltage Noise Density | G = 20/3 |  | 4 |  | nV/√Hz |
| Total RMS Noise, RTI | G = 1/3 |  | 43.7 |  | µV RMS |
| Total RMS Noise, RTI | G = 5/9 |  | 26.8 |  | µV RMS |
| Total RMS Noise, RTI | G = 20/9 |  | 8 |  | µV RMS |
| Total RMS Noise, RTI | G = 20/3 |  | 4 |  | µV RMS |
| Signal-to-Noise Ratio (SNR) | f_{IN} = 1 kHz, −0.5 dBFS |  |  |  |  |
| Signal-to-Noise Ratio (SNR) | G = 1/3 | 105 | 106.5 |  | dBFS |
| Signal-to-Noise Ratio (SNR) | G = 5/9 | 104 | 106 |  | dBFS |
| Signal-to-Noise Ratio (SNR) | G = 20/9 | 103.2 | 105 |  | dBFS |
| Signal-to-Noise Ratio (SNR) | G = 20/3 | 98.8 | 101 |  | dBFS |
| Spurious-Free Dynamic Range (SFDR) | f_{IN} = 1 kHz, −0.5 dBFS |  |  |  |  |
| Spurious-Free Dynamic Range (SFDR) | G = 1/3 |  | 122 |  | dBc |
| Spurious-Free Dynamic Range (SFDR) | G = 5/9 |  | 118 |  | dBc |
| Spurious-Free Dynamic Range (SFDR) | G = 20/9 |  | 122 |  | dBc |
| Spurious-Free Dynamic Range (SFDR) | G = 20/3 |  | 122 |  | dBc |
| Total Harmonic Distortion (THD) | f_{IN} = 1 kHz, −0.5 dBFS |  |  |  |  |
| Total Harmonic Distortion (THD) | G = 1/3 | −114 | −122 |  | dBc |
| Total Harmonic Distortion (THD) | G = 5/9 | −105.5 | −118 |  | dBc |
| Total Harmonic Distortion (THD) | G = 20/9 | −115.5 | −122 |  | dBc |
| Total Harmonic Distortion (THD) | G = 20/3 | −115.5 | −122 |  | dBc |
| Signal-to-Noise-and-Distortion (SINAD) Ratio | f_{IN} = 1 kHz, −0.5 dBFS |  |  |  |  |
| Signal-to-Noise-and-Distortion (SINAD) Ratio | G = 1/3 | 104.7 | 106.4 |  | dBFS |
| Signal-to-Noise-and-Distortion (SINAD) Ratio | G = 5/9 | 103.7 | 105.9 |  | dBFS |
| Signal-to-Noise-and-Distortion (SINAD) Ratio | G = 20/9 | 103 | 104.9 |  | dBFS |
| Signal-to-Noise-and-Distortion (SINAD) Ratio | G = 20/3 | 98.6 | 100.9 |  | dBFS |
| Oversampled Dynamic Range | OSR = 2 |  | 108 |  | dB |
| Oversampled Dynamic Range | OSR = 1024 |  | 134 |  | dB |
| −3 dB Input Bandwidth | V_{OUTDIFF} = 2 V p-p |  |  |  |  |
| −3 dB Input Bandwidth | G = 1/3 |  | 270 |  | kHz |
| −3 dB Input Bandwidth | G = 5/9 |  | 270 |  | kHz |
| −3 dB Input Bandwidth | G = 20/9 |  | 250 |  | kHz |
| −3 dB Input Bandwidth | G = 20/3 |  | 225 |  | kHz |
| Aperture Delay |  |  | 0.7 |  | ns |
| Aperture Jitter |  |  | 1.4 |  | ps RMS |
| **INTERNAL REFERENCE BUFFER** | External reference drives REFIN  |  |  |  |  |
REFIN Voltage Range | 5.3 V ≤ VDD_5V ≤ 5.5 V | 4.95 | 5 | 5.05 | V |
| REFIN Voltage Range | 4.75 V ≤ VDD_5V ≤ 5.25 V | 4.046 | 4.096 | 4.146 | V |
| REFIN Bias Current | REFIN = 5 V |  | 10 | 13.5 | µA |
| REFIN Input Impedance |  |  | 500 |  | kΩ |
| REFIN Input Capacitance |  |  | 40 |  | pF |
| Reference Buffer Offset-Error | REFIN = 5 V or 4.096 V, T_{A} = 25°C | −150 | ±20 | +150 | µV |
| Reference Buffer Offset-Drift |  |  | ±0.3 |  | µV/°C |
| Power-On Settling Time |  |  | 3 |  | ms |
| **DIGITAL INPUTS, ADC** | 1.14 V ≤ V_{IO} ≤ 1.89 V |  |  |  |  |
| Logic Levels |  |  |  |  |  |
| Input Voltage Low (V_{IL}) |  | −0.3 |  | +0.35 × V_{IO} | V |
| Input Voltage High (V_{IH}) |  | 0.65 × V_{IO} |  | V_{IO} + 0.3 | V |
| Input Current Low (I_{IL}) |  | −10 |  | +10 | µA |
| Input Current High (I_{IH}) |  | −10 |  | +10 | µA |
| Input Pin Capacitance |  |  | 2 |  | pF |
| **DIGITAL INPUTS, A0 and A1** |  |  |  |  |  |
| Logic Levels |  |  |  |  |  |
| Input Voltage Low (V_{IL}) |  |  |  | 0.8 | V |
| Input Voltage High (V_{IH}) |  | 2 |  |  | V |
| Input Current (I_{IL} or I_{IH}) |  |  | 0.002 |  | µA |
| Input Pin Capacitance |  |  | 2 |  | pF |
| **DIGITAL INPUTS, FDA** |  |  |  |  |  |
| PDB_FDA Input Current | PDB_FDA = VDD_FDA or 0 V |  | 50 |  | µA |
| **DIGITAL INPUTS, TEMPERATURE SENSOR (SDA AND SCL)** |  |  |  |  |  |
| Logic Levels |  |  |  |  |  |
| Input Voltage Low (V_{IL}) |  | −0.5 |  | V_{DD} × 0.3 | V |
| Input Voltage High (V_{IH}) | V_{DD} = 3.3 V | V_{DD} × 0.7 |  | 3.6 | V |
| Input Voltage High (V_{IH}) | V_{DD} = 1.6 V | V_{DD} × 0.8 |  | 3.6 | V |
| Input High-Leakage Current |  |  |  | +1 | µA |
| Input Low-Leakage Current |  | −1 | ±0.005 | +1 | µA |
| Input Capacitance |  |  | 5 |  | pF |
| **DIGITAL OUTPUTS** | 1.14 V ≤ V_{IO} ≤ 1.89 V | Conversion results available immediately after completed conversion |  |  |  |
| Pipeline Delay |  |  |  |  |  |
| Output Voltage Low (V_{OL}) | Sink current (I_{SINK}) = 2 mA |  |  | 0.25 × V_{IO} | V |
| Output Voltage High (V_{OH}) | Source current (I_{SOURCE}) = 2 mA | 0.75 × V_{IO} |  |  | V |
| **LDO CHARACTERISTICS** |  |  |  |  |  |
| VDD_1.8V Output Voltage |  | 1.71 | 1.8 | 1.89 | V |
| Load Regulation | Output current (I_{OUT}) = 1 mA to 100 mA |  | 0.003 |  | %/mA |
| Dropout Voltage[^6] | I_{OUT} = 100 mA |  | 45 |  | mV |
| Start-up Time[^7] |  |  | 200 |  | µs |
| Current Limit Threshold |  |  | 260 |  | mA |
| EN_LDO Input Current | EN_LDO = V_{LDO} |  | 0.001 | 1 | µA |
| Thermal Shutdown Threshold |  |  | 150 |  | °C |
| Thermal Shutdown Hysteresis |  |  | 15 |  | °C |
| **TEMPERATURE SENSOR CHARACTERISTICS** |  |  |  |  |  |
| Temperature Measurement Error | T = −40°C to +105°C | −1 | ±0.3 | +1 | °C |
| Conversion Time | 10-bit resolution, T = 25°C |  | 35 | 150 | ms |
| Temperature Resolution | 12-bit (Configuration Bits[D6:D5] = 11) |  | 0.0625 |  | °C |
| Temperature Resolution | 10-bit (Configuration Bits[D6:D5] = 10) |  | 0.25 |  | °C |
| Temperature Resolution | 9-bit (Configuration Bits[D6:D5] = 01) |  | 0.5 |  | °C |
| Temperature Resolution | 8-bit (Configuration Bits[D6:D5] = 00) |  | 1.0 |  | °C |
| First Conversion Completed | After V_{DD} exceeds 1.6 V |  |  | 500 | ms |
| ISOLATION LEAKAGE CURRENT | ±250 V between GND and TMP_GND planes |  | 1 |  | nA |
| **POWER SUPPLIES** |  |  |  |  |  |
| V_{DDH} |  |  | 18 |  | V |
| V_{SSH} |  |  | −18 |  | V |
| VDD_FDA |  | 3 | 5.4 | VSS_FDA + 10 | V |
| VSS_FDA |  | VDD_FDA − 10 | 0 | +0.1 | V |
| VDD_5V | REF = 5 V | 5.3 | 5.4 | 5.5 | V |
| VDD_5V | REF = 4.096 V | 4.75 | 5 | 5.25 | V |
| VDD_1.8V |  | 1.71 | 1.8 | 1.89 | V |
| V_{IO}[^8] |  | 1.14 | 1.8 | 1.89 | V |
| VDD |  | 1.6 | 3.3 | 3.6 | V |
| VLDO |  | 2.2 | 5.4 | 5.5 | V |
| Standby Current | Inputs grounded |  |  |  |  |
| V_{DDH} |  |  | 8 |  | mA |
| V_{SSH} |  |  | −9 |  | mA |
| VDD_FDA |  |  | 4.8 |  | mA |
| VSS_FDA |  |  | −3.5 |  | mA |
| VDD_5V |  |  | 525 |  | µA |
| V_{IO} |  |  | <1 |  | µA |
| V_{DD} |  |  | 1.5 | 4.5 | µA |
| V_{LDO} |  |  | 108 |  | µA |
| Shutdown Current | Inputs grounded |  |  |  |  |
| VDD_FDA | PDB_FDA = 0 V |  | 32 |  | µA |
| VSS_FDA | PDB_FDA = 0 V |  | −25.5 |  | µA |
| VDD_5V | ADC in Shutdown Mode |  | 5 |  | µA |
| V_{IO} |  |  | <1 |  | µA |
| V_{LDO} | EN_LDO = 0 V, ADC in shutdown mode |  | 0.8 |  | µA |
| Operating Current | 2 MSPS, Input = −0.5 dBFS |  |  |  |  |
| V_{DDH} | V_{DDH} = +18 V |  | 10 |  | mA |
| V_{SSH} | V_{SSH} = −18 V |  | −9.8 |  | mA |
| VDD_5V | VDD_5V = 5.4 V |  | 2.5 | 3.2 | mA |
| VDD_FDA | VDD_FDA = 5 V |  | 5.6 | 7.5 | mA |
| VSS_FDA | VSS_FDA = 0 V | −7.5 | −5.6 |  | mA |
| V_{IO} | V_{IO} = 1.8 V, 1-lane SDO |  | 1.3 |  | mA |
| V_{LDO} | V_{LDO} = 5.4 V |  | 8.2 | 10.5 | mA |
| V_{DD} | V_{DD} = 3.3 V |  | 80 | 150 | µA |
| Power Dissipation | 2 MSPS |  | 446 |  | mW |
| t_{RESET_DELAY} | After power-on, delay from VDD_5V and VDD_1.8V valid to R̅S̅T̅ assertion | 3 |  |  | ms |
| t_{RESET_PW} | R̅S̅T̅ pulse width | 50 |  |  | ns |
| **TEMPERATURE RANGE** |  |  |  |  |  |
| Specified Performance | T_{MIN} to T_{MAX} | −40 |  | +105 | °C |

- **Note 1:** The differential input ranges, V_{IN}, must be within the allowed input common-mode range as per Figure 78 to Figure 81. VDDH should have a +3.5 V headroom from the peak input voltage.
- **Note 2:** The acquisition phase is the time available for the input sampling capacitors to acquire a new input with the ADC running at a throughput rate of 2 MSPS.
- **Note 3:** These specifications are not production tested but are supported by characterization data during the initial product release.
- **Note 4:** Tested at 95% of full scale input.
- **Note 5:** See the low-frequency noise plot in Figure 61. 1/f noise is canceled internally by auto-zeroing. Noise spectral density is substantially uniform from DC to f_{S}/2.
- **Note 6:** Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage.
- **Note 7:** Start-up time is defined as the time between the rising edge of EN_LDO to VDD_1.8V being at 90% of its nominal value.
- **Note 8:** When V_{IO} < 1.4 V, Bit IO2X must be set to 1. For more details, see the Output Driver Register section.

### TIMING SPECIFICATIONS
<!-- page: 9 -->

V_{DDH}  = 18 V, V_{SSH} = -18 V, VDD\_FDA = 5.4 V, VSS\_FDA = 0 V, VDD\_5V = 5.4 V, V_{LDO} = 5.4 V, V_{IO} = 1.8 V, REFIN = 5 V, V_{DD} = 3.3 V, f_{S} = 2 MSPS and all specifications are T_{MIN} to T_{MAX} , unless otherwise noted. For the timing voltage levels, see Figure 2. For V_{IO} < 1.4 V, Bit IO2X must be set to 1.

**Table 2. Digital Timing Interface** ([table-01-p9-spec.csv](adaq4224/tables/table-01-p9-spec.csv), p. 9)

| PARAMETER[^1] | SYMBOL | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| Conversion Time: CNV Rising Edge to Data Available | t_{CONV} | 264 | 282 | 300 | ns |
| Acquisition Phase[^2] | t_{ACQ} | 244 | 260 | 275 | ns |
| Time Between Conversions | t_{CYC} | 500 |  |  | ns |
| CNV High Time | t_{CNVH} | 10 |  |  | ns |
| CNV Low Time | t_{CNVL} | 20 |  |  | ns |
| Internal Oscillator Frequency | f_{OSC} | 75.1 | 80 | 84.7 | MHz |

- **Note 1:** Timing specifications assume a 5 pF load capacitance on digital output pins. t_{CONV}, t_{CYC}, t_{SCK}, and t_{SCKOUT} are production tested. All other timing specifications are guaranteed by characterization and design.
- **Note 2:** The acquisition phase is the time available for the input sampling capacitors to acquire a new input with the ADC running at a throughput rate of 2 MSPS.

  ![Figure 2. Voltage Levels for Timing](adaq4224/figures/adaq4224-f003.png)

*Figure 2. Voltage Levels for Timing*

**Table 3. Register Read/Write Timing** ([table-02-p9-spec.csv](adaq4224/tables/table-02-p9-spec.csv), p. 9)

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNITS | CONDITIONS |
|---|---|---|---|---|---|---|
| C̅S̅ Pulse Width | t_{CSPW} | 10 |  |  | ns |  |
| **SCK Period** | t_{SCK} |  |  |  |  |  |
| V_{IO} > 1.71 V |  | 11.6 |  |  | ns |  |
| V_{IO} > 1.14 V |  | 12.3 |  |  | ns |  |
| SCK Low Time | t_{SCKL} | 5.2 |  |  | ns |  |
| SCK High Time | t_{SCKH} | 5.2 |  |  | ns |  |
| SCK Falling Edge to Data Remains Valid | t_{HSDO} | 2.1 |  |  | ns |  |
| SCK Falling Edge to Data Valid Delay | t_{DSDO} |  |  |  |  |  |
| SCK Falling Edge to Data Valid Delay | t_{DSDO} |  |  | 9.4 | ns | V_{IO} > 1.71 V |
| SCK Falling Edge to Data Valid Delay | t_{DSDO} |  |  | 11.8 | ns | V_{IO} > 1.14 V |
| C̅S̅ Rising Edge to SDO High Impedance | t_{CSDIS} |  |  | 9 | ns |  |
| SDI Valid Setup Time to SCK Rising Edge | t_{SSDI} | 1.5 |  |  | ns |  |
| SDI Valid Hold Time from SCK Rising Edge | t_{HSDI} | 1.5 |  |  | ns |  |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} |  |  |  |  |  |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} |  |  | 11.6 | ns | V_{IO} > 1.71 V |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} |  |  | 12.3 | ns | V_{IO} > 1.14 V |
| Last SCK Edge to C̅S̅ Rising Edge | t_{SCKCS} | 5.2 |  |  | ns |  |


![Figure 3. Register Configuration Mode Write Timing](adaq4224/figures/adaq4224-f004.png)

*Figure 3. Register Configuration Mode Write Timing*

![Figure 4. Register Configuration Mode Read Timing](adaq4224/figures/adaq4224-f005.png)

*Figure 4. Register Configuration Mode Read Timing*

![Figure 5. Register Configuration Mode Command Timing](adaq4224/figures/adaq4224-f006.png)

*Figure 5. Register Configuration Mode Command Timing*

**Table 4. SPI-Compatible Mode Timing** ([table-03-p10-spec.csv](adaq4224/tables/table-03-p10-spec.csv), p. 10)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| SCK Period | t_{SCK} |  |  |  |  |  |
| SCK Period | t_{SCK} | V_{IO} > 1.71 V | 9.8 |  |  | ns |
| SCK Period | t_{SCK} | V_{IO} > 1.14 V | 12.3 |  |  | ns |
| SCK Low Time | t_{SCKL} |  |  |  |  |  |
| SCK Low Time | t_{SCKL} | V_{IO} > 1.71 V | 4.2 |  |  | ns |
| SCK Low Time | t_{SCKL} | V_{IO} > 1.14 V | 5.2 |  |  | ns |
| SCK High Time | t_{SCKH} |  |  |  |  |  |
| SCK High Time | t_{SCKH} | V_{IO} > 1.71 V | 4.2 |  |  | ns |
| SCK High Time | t_{SCKH} | V_{IO} > 1.14 V | 5.2 |  |  | ns |
| SCK Falling Edge to Data Remains Valid | t_{HSDO} |  | 1.4 |  |  | ns |
| SCK Falling Edge to Data Valid Delay | t_{DSDO} |  |  |  |  |  |
| SCK Falling Edge to Data Valid Delay | t_{DSDO} | V_{IO} > 1.71 V |  |  | 5.6 | ns |
| SCK Falling Edge to Data Valid Delay | t_{DSDO} | V_{IO} > 1.14 V |  |  | 8.1 | ns |
| C̅S̅ Falling Edge to SDO Valid | t_{CSEN} |  |  |  |  | ns |
| C̅S̅ Falling Edge to SDO Valid | t_{CSEN} | V_{IO} > 1.71 V |  |  | 6.8 | ns |
| C̅S̅ Falling Edge to SDO Valid | t_{CSEN} | V_{IO} > 1.14 V |  |  | 9.3 | ns |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} |  |  |  |  |  |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} | V_{IO} > 1.71 V | 9.8 |  |  | ns |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} | V_{IO} > 1.14 V | 12.3 |  |  | ns |
| Last SCK Edge to C̅S̅ Rising Edge | t_{SCKCS} |  | 4.2 |  |  | ns |
| C̅S̅ Rising Edge to SDO High Impedance | t_{CSDIS} |  |  |  | 9 | ns |
| C̅S̅ Falling Edge to BUSY Rising Edge | t_{CSBUSY} |  |  | 6 |  | ns |


![Figure 6. SPI Clocking Mode 1-Lane SDR Timing](adaq4224/figures/adaq4224-f007.png)

*Figure 6. SPI Clocking Mode 1-Lane SDR Timing*

**Table 5. Echo-Clock Mode Timing, SDR, 1-Lane** ([table-04-p11-spec.csv](adaq4224/tables/table-04-p11-spec.csv), p. 11)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| SCK Period | t_{SCK} | V_{IO} > 1.71 V | 9.8 |  |  | ns |
| SCK Period | t_{SCK} | V_{IO} > 1.14 V | 12.3 |  |  | ns |
| SCK Low Time, SCK High Time | t_{SCKL}, t_{SCKH} | V_{IO} > 1.71 V | 4.2 |  |  | ns |
| SCK Low Time, SCK High Time | t_{SCKL}, t_{SCKH} | V_{IO} > 1.14 V | 5.2 |  |  | ns |
| SCK Rising Edge to Data/SCKOUT Remains Valid | t_{HSDO} |  | 1.1 |  |  | ns |
| SCK Rising Edge to Data/SCKOUT Valid Delay | t_{DSDO} | V_{IO} > 1.71 V |  |  | 5.6 | ns |
| SCK Rising Edge to Data/SCKOUT Valid Delay | t_{DSDO} | V_{IO} > 1.14 V |  |  | 8.1 | ns |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} | V_{IO} > 1.71 V | 9.8 |  |  | ns |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} | V_{IO} > 1.14 V | 12.3 |  |  | ns |
| Skew Between Data and SCKOUT | t_{SKEW} |  | −0.4 | 0 | +0.4 | ns |
| Last SCK Edge to C̅S̅ Rising Edge | t_{SCKCS} |  | 4.2 |  |  | ns |
| C̅S̅ Rising Edge to SDO High Impedance | t_{CSDIS} |  |  |  | 9 | ns |


![Figure 7. Echo-Clock Mode Timing, SDR, 1-Lane](adaq4224/figures/adaq4224-f008.png)

*Figure 7. Echo-Clock Mode Timing, SDR, 1-Lane*

**Table 6. Echo-Clock Mode Timing, DDR, 1-Lane** ([table-05-p12-spec.csv](adaq4224/tables/table-05-p12-spec.csv), p. 12)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| SCK Period | t_{SCK} |  | 12.3 |  |  | ns |
| SCK Low Time, SCK High Time | t_{SCKL}, t_{SCKH} |  | 5.2 |  |  | ns |
| SCK Edge to Data/SCKOUT Remains Valid | t_{HSDO} |  | 1.1 |  |  | ns |
| SCK Edge to Data/SCKOUT Valid Delay | t_{DSDO} |  |  |  |  |  |
| SCK Edge to Data/SCKOUT Valid Delay | t_{DSDO} | V_{IO} > 1.71 V |  |  | 6.2 | ns |
| SCK Edge to Data/SCKOUT Valid Delay | t_{DSDO} | V_{IO} > 1.14 V |  |  | 8.7 | ns |
| C̅S̅ Falling Edge to First SCK Rising Edge | t_{CSSCK} |  | 12.3 |  |  | ns |
| Skew Between Data and SCKOUT | t_{SKEW} |  | −0.4 | 0 | +0.4 | ns |
| Last SCK Edge to C̅S̅ Rising Edge | t_{SCKCS} |  | 9 |  |  | ns |
| C̅S̅ Rising Edge to SDO High Impedance | t_{CSDIS} |  |  |  | 9 | ns |


![Figure 8. Echo-Clock Mode Timing, DDR, 1-Lane](adaq4224/figures/adaq4224-f009.png)

*Figure 8. Echo-Clock Mode Timing, DDR, 1-Lane*

**Table 7. Host-Clock Mode Timing** ([table-06-p12-spec.csv](adaq4224/tables/table-06-p12-spec.csv), p. 12)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| SCK Period | t_{SCKOUT} |  |  |  |  |  |
| SCK Period | t_{SCKOUT} | OSC_DIV = No Divide | 11.8 | 12.5 | 13.3 | ns |
| SCK Period | t_{SCKOUT} | OSC_DIV = Divide by 2 | 23.6 | 25 | 26.6 | ns |
| SCK Period | t_{SCKOUT} | OSC_DIV = Divide by 4 | 47.4 | 50 | 53.2 | ns |
| SCK Low Time | t_{SCKOUTL} |  | 0.45 × t_{SCKOUT} |  | 0.55 × t_{SCKOUT} | ns |
| SCK High Time | t_{SCKOUTH} |  | 0.45 × t_{SCKOUT} |  | 0.55 × t_{SCKOUT} | ns |
| C̅S̅ Falling Edge to First SCKOUT Rising Edge | t_{DSCKOUT} |  |  |  |  |  |
| C̅S̅ Falling Edge to First SCKOUT Rising Edge | t_{DSCKOUT} | V_{IO} > 1.71 V | 10 | 13.6 | 19 | ns |
| C̅S̅ Falling Edge to First SCKOUT Rising Edge | t_{DSCKOUT} | V_{IO} > 1.14 V | 10 | 15 | 21 | ns |
| Skew Between Data and SCKOUT | t_{SKEW} |  | −0.4 | 0 | +0.4 | ns |
| Last SCKOUT Edge to C̅S̅ Rising Edge | t_{SCKOUTCS} |  | 5.2 |  |  | ns |
| C̅S̅ Rising Edge to SDO High Impedance | t_{CSDIS} |  |  |  | 9 | ns |

![Figure 9. Host-Clock Mode Timing, SDR, 1-Lane](adaq4224/figures/adaq4224-f010.png)

*Figure 9. Host-Clock Mode Timing, SDR, 1-Lane*

![Figure 10. Host-Clock Mode Timing, DDR, 1-Lane](adaq4224/figures/adaq4224-f011.png)

*Figure 10. Host-Clock Mode Timing, DDR, 1-Lane*

**Table 8. Temperature Sensor I^{2}C Timing** ([table-07-p13-spec.csv](adaq4224/tables/table-07-p13-spec.csv), p. 13)

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| Serial Clock Frequency | f_{SCL} | 20 |  | 1M | Hz |
| Bus Free Time Between Start and Stop Conditions | t_{BUF} | 0.5 |  |  | µs |
| START Condition Hold Time | t_{HD:STA} | 0.26 |  |  | µs |
| STOP Condition Setup Time[^1] | t_{SU:STO} | 0.26 |  |  | µs |
| Clock Low Period | t_{LOW} | 0.5 |  |  | µs |
| Clock High Period | t_{HIGH} | 0.26 |  |  | µs |
| Start Condition Setup Time[^2] | t_{SU:STA} | 0.26 |  |  | µs |
| Data Setup Time[^3] | t_{SU:DAT} | 50 |  |  | ns |
| Data In Hold Time[^4] | t_{HD:DAT} | 0 |  |  | µs |
| SCL/SDA Rise Time | t_{R} |  |  | 120 | ns |
| SCL/SDA Fall Time[^5] | t_{F} | 20 × (V_{DD}/5.5 V) |  | 120 | ns |
| SCL Time Low for Reset of Serial Interface[^6] | t_{TIMEOUT} | 10 |  | 85 | ms |

- **Note 1:** 90% of SCL to 10% of SDA.
- **Note 2:** 90% of SCL to 90% of SDA.
- **Note 3:** 10% of SDA to 10% of SCL.
- **Note 4:** 10% of SCL to 10% of SDA.
- **Note 5:** C_{B} = total capacitance of one bus line in pF. Tested with C_{B} = 400 pF.
- **Note 6:** Holding the SCL line low for a time greater than t_{TIMEOUT} causes the device to reset SDA to the idle state of the serial bus communication (SDA released).


![Figure 11. Temperature Sensor I 2 C Timing Diagram](adaq4224/figures/adaq4224-f012.png)

*Figure 11. Temperature Sensor I^{2}C Timing Diagram*

### ABSOLUTE MAXIMUM RATINGS
<!-- page: 14 -->

### Table 9. Absolute Maximum Ratings
<!-- page: 14 -->

**Table 9. Absolute Maximum Ratings** ([table-08-p14-abs_max.csv](adaq4224/tables/table-08-p14-abs_max.csv), p. 14)

| PARAMETER | RATING |
|---|---|
| **Analog Inputs** |  |
| Input Voltage, INP, INN | V_{SSH} − 0.2 V to V_{DDH} + 0.2 V |
| REFIN to GND | −0.3 V to VDD_5V + 0.3 V |
| Input Current[^1] | ±20 mA |
| **Supply Voltage** |  |
| V_{DDH} to V_{SSH} | 40 V |
| VDD_FDA to GND | 11 V |
| VDD_5V to GND | −0.3 V to +6.0 V |
| V_{IO} to GND | −0.3 V to +2.1 V |
| V_{LDO} to GND | −0.3 V to +6.5 V |
| V_{DD} to TMP_GND | −0.3 V to +4 V |
| Digital Inputs to GND | −0.3 V to V_{IO} + 0.3 V |
| CNV to GND | −0.3 V to V_{IO} + 0.3 V |
| RSEL, ALARM, SCL, SDA to TMP_GND | −0.3 V to +4 V |
| Digital Outputs to GND | −0.3 V to V_{IO} + 0.3 V |
| **Temperature** |  |
| Storage Range | −55°C to +150°C |
| Operating Junction Range | −40°C to +105°C |
| Maximum Reflow (Package Body) | 260°C |

- **Note 1:** The input pins have clamp diodes connected to the power supply pins. Whenever input signals exceed the power supply rail by 0.3 V, limit the input current to 20 mA or less.

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

### THERMAL RESISTANCE
<!-- page: 14 -->

Thermal performance is directly linked to printed circuit board (PCB) design and operating environment. Careful attention to PCB thermal design is required. θ_{JA} is the natural convection junction-toambient thermal resistance measured in a one cubic foot sealed enclosure. θ_{JC} is the junction-to-case thermal resistance.

### Table 10. Thermal Resistance
<!-- page: 14 -->

**Table 10. Thermal Resistance** ([table-09-p14-data.csv](adaq4224/tables/table-09-p14-data.csv), p. 14)

| Package Type | θ_{JA} | θ_{JC_TOP} | θ_{JC_BOT} | Ψ_{JT} | Unit |
|---|---|---|---|---|---|
| BC-178-2 | 28.96 | 22.60 | 14.09 | 14.03 | °C/W |

### ELECTROSTATIC DISCHARGE (ESD) RATINGS
<!-- page: 14 -->

The following ESD information is provided for handling of ESD-sensitive devices in an ESD protected area only.

Human body model (HBM) per ANSI/ESDA/JEDEC JS-001.  
Field-induced charged device model (FICDM) per ANSI/ESDA/JEDEC JS-002.

### ESD Ratings for ADAQ4224
<!-- page: 14 -->

**Table 11. ADAQ4224, 178-Ball CSP_BGA** ([table-10-p14-data.csv](adaq4224/tables/table-10-p14-data.csv), p. 14)

| ESD Model | Withstand Threshold (kV) | Class |
|---|---|---|
| HBM | ±4 | 3A |
| FICDM | ±1 | C3 |

### ESD CAUTION
<!-- pages: 14-15 -->

ESD (electrostatic discharge) sensitive device . Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

### PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
<!-- pages: 15-17 -->

![Figure 12. Pin Configuration (Top View)](adaq4224/figures/adaq4224-f014.png)

*Figure 12. Pin Configuration (Top View)*

**Table 12. Pin Function Descriptions** ([table-11-p15-pin.csv](adaq4224/tables/table-11-p15-pin.csv), p. 15)

| NUMBER | NAME | TYPE[^1] | DESCRIPTION |
|---|---|---|---|
| A1 to A4, A7 to A11, A17, B1 to B11, B17, C2, C5, C8 to C11, C17, D2 to D10, D13 to D14, E1 to E2, E5, E7 to E8, E11, E13 to E14, F1 to F5, F7 to F8, F11 to F14, G1 to G2, G5 to G6, G8 to G10, G13 to G14, H1 to H6, H8 to H10, H13 to H14, J1 to J2, J5, J7 to J9, J11 to J14, K1 to K5, K7 to K9, K11, K13 to K14, L1 to L6, L9 to L11, L13 | GND | P | Power Supply Ground. |
| A5 to A6, J3 to J4 | VDDH | P | PGIA Positive Power Supply. This pin has a 0.1 µF bypass capacitor inside the package. |
| A13 | TMP_GND | P | Temperature Sensor Ground Return Path. Connect to GND if the VDD pin is connected to the VIO pin. |
| A14 | VDD | P | Temperature Sensor Power Supply. Supply can range from 1.6 V to 3.6 V or connect to VIO (1.8 V only) for fewer supply rails. This pin has a 0.1 µF bypass capacitor connected to TMP_GND inside the package. |
| A15 | ALARM | DO | Temperature Sensor Alarm Output. Active when the temperature measured is above the TH or below TL thresholds. Configurable active high/low. It is an open-drain output and requires a pull-up resistor to operate. |
| B13 | RSEL | DI | Connect a resistor between this pin and TMP_GND. Used to uniquely identify up to 32 target devices connected on the same temperature sensor I^{2}C bus. Connect to TMP_GND if only one device is used. |
| B14 | SCL | DI | Temperature Sensor I^{2}C Clock. |
| B15 | SDA | DI | Temperature Sensor I^{2}C Bus Data Line. |
| C1, D1 | INP | AI | Positive Analog Input. Do not leave the INP pin floating. Leaving the INP pin floating can cause the PGIA to draw a larger current from the VDDH and VSSH supply. |
| C3 to C4, G3 to G4 | VSSH | P | PGIA Negative Power Supply. This pin has a 0.1 µF bypass capacitor inside the package. |
| C6 to C7 | INN | AI | Negative Analog Input. Do not leave the INN pin floating. Leaving the INN pin floating can cause the PGIA to draw a larger current from the VDDH and VSSH supply. |
| D11 | REFIN | AI | Reference Input. Drive REFIN with 4.096 V to 5 V (referred to ground). This pin has the input of the internal reference buffer and has an internal 2 µF bypass capacitor connected to the output of the buffer. |
| D12, E12 | VDD_5V | P | 5 V Power Supply. The range of VDD_5V depends on the reference value, 5.3 V to 5.5 V for a 5 V reference, and 4.75 V to 5.25 V for a 4.096 V reference. This pin has a 1 µF and 0.1 µF bypass capacitors inside the package. |
| D15 | CNV | DI | Convert Input. A rising edge on this input powers up the device and initiates a new conversion. This signal must have low jitter to achieve the specified performance of the ADC. Logic levels are determined by the VIO pin. |
| D16 | RSTB | DI | Reset Input (Active Low). Asynchronous ADC reset. |
| D17, E17 | VIO | P | Input/Output Interface Digital Power. Nominally, this pin is at the same supply as the host interface (1.8 V, 1.5 V, or 1.2 V). This pin has a 0.2 µF bypass capacitor inside the package. For VIO < 1.4 V, Bit IO2X of the output driver register must be set to 1. |
| E3 | A1 | DI | PGIA Gain-Control Logic Input 1. |
| E4 | A0 | DI | PGIA Gain-Control Logic Input 0. |
| E6, F6 | VDD_FDA | P | FDA Positive Power Supply. This pin has a 0.1 µF bypass capacitor inside the package. Bypass this pin to GND with at least 2.2 µF (0402, X5R) ceramic capacitor. |
| E9 | OUTP | AO | Positive FDA Output. Connect to ADCP pin. |
| E10 | ADCP | AI | Positive ADC Input. Connect to OUTP pin. |
| E15 to E16, F15, G15, H15 to H16, J15, K15, L17 | IOGND | P | VIO Ground. Connect to the same ground plane as all GND pins. |
| F9 | OUTN | AO | Negative FDA Output. Connect to ADCN pin. |
| F10 | ADCN | AI | Negative ADC Input. Connect to OUTN pin. |
| F16 | SDO3 | DO | Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. |
| F17 | SDO1 | DO | Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. |
| G7, G11 to G12, H11 to H12 | DNC |  | Do Not Connect. |
| G16 | SDO2 | DO | Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. |
| G17 | SDO0 | DO | Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. |
| H7 | PDB_FDA | DI | Power-Down FDA. Active low. Connect the PDB_FDA pin to GND to power down the FDA. Otherwise, connect the PDB_FDA pin to VDD_FDA logic high supply. |
| H17 | BUSY_SCKOUT | DO | BUSY Indicator in SPI Clocking Mode. This pin goes high at the start of a new conversion and returns low when the conversion finishes. Logic levels are determined by the VIO pin. When SCKOUT is enabled, this pin function is either an echo of the incoming SCK from the host controller or a clock sourced by the internal oscillator. |
| J6, K6 | VSS_FDA | P | FDA Negative Supply. This pin has a 0.1 µF bypass capacitor inside the package. Bypass this pin to GND with at least 2.2 µF (0402, X5R) ceramic capacitor. Connect to GND for fewer power supply rails. |
| J10, K10 | NIC |  | Not Internally Connected. These pins are not connected internally. |
| J16 to J17, K16 to K17 | DNC |  | Do Not Connect. These pins are internally connected to digital output drivers in high-Z mode. |
| K12, L12 | VDD_1.8V | P | LDO Voltage Output. The output is typically at 1.8 V. This pin has a 1 µF and 0.1 µF bypass capacitors inside the package. |
| L7 | EN_LDO | DI | Enable LDO pin. For automatic start-up, connect EN_LDO to VLDO. |
| L8 | VLDO | P | Internal LDO Input Supply. This pin has a 1 µF bypass capacitor inside the package. The input range for VLDO is 2.2 V to 5.5 V. |
| L14 | CSB | DI | Chip Select Input (Active Low). |
| L15 | SDI | DI | Serial Data Input. |
| L16 | SCK | DI | Serial-Data Clock Input. When the device is selected (CSB = low), the conversion result is shifted out by this clock. |

- **Note 1:** AI is analog input, AO is analog output, P is power, DI is digital input, and DO is digital output.


### TYPICAL PERFORMANCE CHARACTERISTICS
<!-- pages: 17-31 -->
V_{DDH} = 18 V, V_{SSH} = −18 V, VDD_FDA = 5.4 V, VSS_FDA = 0 V, VDD_5V = 5.4 V, V_{LDO} = 5.4 V, VDD_1.8V = 1.8 V, V_{IO} = 1.8 V, REFIN = 5 V,
f_{S} = 2 MSPS, and all specifications T_{MIN} to T_{MAX}, unless otherwise noted.

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

0:0

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

*[Equation not captured in extraction — see the PDF.]*

![Figure 13. INL Error vs. Output Code, Differential Input, REFIN = 5 V](adaq4224/figures/adaq4224-f015.png)

*Figure 13. INL Error vs. Output Code, Differential Input, REFIN = 5 V*

Digitized data: [inl-error-vs-output-code-differential-input-refin-5-v.csv](adaq4224/curves/inl-error-vs-output-code-differential-input-refin-5-v.csv) (x: M (output codes); y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 14. INL Error vs. Output Code, Single-Ended Input, REFIN = 5 V](adaq4224/figures/adaq4224-f016.png)

*Figure 14. INL Error vs. Output Code, Single-Ended Input, REFIN = 5 V*

Digitized data: [inl-error-vs-output-code-single-ended-input-refin-5-v.csv](adaq4224/curves/inl-error-vs-output-code-single-ended-input-refin-5-v.csv) (x: M; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 15. INL Error vs. Output Code across Temperature, G = 1/3](adaq4224/figures/adaq4224-f017.png)

*Figure 15. INL Error vs. Output Code across Temperature, G = 1/3*

Digitized data: [inl-error-vs-output-code-across-temperature-g-1-3.csv](adaq4224/curves/inl-error-vs-output-code-across-temperature-g-1-3.csv) (x: M; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 16. INL Error vs. Output Code, Differential Input, REFIN = 4.096 V](adaq4224/figures/adaq4224-f018.png)

*Figure 16. INL Error vs. Output Code, Differential Input, REFIN = 4.096 V*

Digitized data: [inl-error-vs-output-code-differential-input-refin-4-096-v.csv](adaq4224/curves/inl-error-vs-output-code-differential-input-refin-4-096-v.csv) (x: M; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 17. INL Error vs. Output Code, Single-Ended Input, REFIN = 4.096 V](adaq4224/figures/adaq4224-f019.png)

*Figure 17. INL Error vs. Output Code, Single-Ended Input, REFIN = 4.096 V*

Digitized data: [inl-error-vs-output-code-single-ended-input-refin-4-096-v.csv](adaq4224/curves/inl-error-vs-output-code-single-ended-input-refin-4-096-v.csv) (x: M; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 18. INL Error vs. Output Code across Temperature, G = 5/9](adaq4224/figures/adaq4224-f020.png)

*Figure 18. INL Error vs. Output Code across Temperature, G = 5/9*

Digitized data: [inl-error-vs-output-code-across-temperature-g-5-9.csv](adaq4224/curves/inl-error-vs-output-code-across-temperature-g-5-9.csv) (x: M (output codes); y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 19. INL Error vs. Output Code across Temperature, G = 20/9](adaq4224/figures/adaq4224-f021.png)

*Figure 19. INL Error vs. Output Code across Temperature, G = 20/9*

Digitized data: [inl-error-vs-output-code-across-temperature-g-20-9.csv](adaq4224/curves/inl-error-vs-output-code-across-temperature-g-20-9.csv) (x: M; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 20. Code Histogram for Shorted Inputs, REFIN = 5 V](adaq4224/figures/adaq4224-f022.png)

*Figure 20. Code Histogram for Shorted Inputs, REFIN = 5 V*

Digitized data: [code-histogram-for-shorted-inputs-refin-5-v.csv](adaq4224/curves/code-histogram-for-shorted-inputs-refin-5-v.csv) (x: CODES; y: G = 20/3; σ = 44.3) — values read off the printed plot by the digitizer, not published data.

![Figure 21. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 1/3](adaq4224/figures/adaq4224-f023.png)

*Figure 21. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 1/3*

![Figure 22. INL Error vs. Output Code across Temperature, G = 20/3](adaq4224/figures/adaq4224-f024.png)

*Figure 22. INL Error vs. Output Code across Temperature, G = 20/3*

Digitized data: [inl-error-vs-output-code-across-temperature-g-20-3.csv](adaq4224/curves/inl-error-vs-output-code-across-temperature-g-20-3.csv) (x: M; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 23. Code Histogram for Shorted Inputs, REFIN = 4.096 V](adaq4224/figures/adaq4224-f025.png)

*Figure 23. Code Histogram for Shorted Inputs, REFIN = 4.096 V*

Digitized data: [code-histogram-for-shorted-inputs-refin-4-096-v.csv](adaq4224/curves/code-histogram-for-shorted-inputs-refin-4-096-v.csv) (x: CODES; y: k) — values read off the printed plot by the digitizer, not published data.

![Figure 24. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 1/3](adaq4224/figures/adaq4224-f026.png)

*Figure 24. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 1/3*

![Figure 25. FFT, 2 MSPS, f_{IN} = 1 kHz , Differential Input = -0.5 dBFS, G = 5/9](adaq4224/figures/adaq4224-f027.png)

*Figure 25. FFT, 2 MSPS, f_{IN} = 1 kHz , Differential Input = -0.5 dBFS, G = 5/9*

![Figure 26. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/9](adaq4224/figures/adaq4224-f028.png)

*Figure 26. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/9*

![Figure 27. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/3](adaq4224/figures/adaq4224-f029.png)

*Figure 27. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/3*

![Figure 28. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 5/9](adaq4224/figures/adaq4224-f030.png)

*Figure 28. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 5/9*

![Figure 29. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/9](adaq4224/figures/adaq4224-f031.png)

*Figure 29. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/9*

![Figure 30. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/3](adaq4224/figures/adaq4224-f032.png)

*Figure 30. FFT, 2 MSPS, f_{IN} = 1 kHz, Differential Input = -0.5 dBFS, G = 20/3*

![Figure 31. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz](adaq4224/figures/adaq4224-f033.png)

*Figure 31. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz*

Digitized data: [snr-sinad-vs-input-amplitude-at-f-in-1-khz.csv](adaq4224/curves/snr-sinad-vs-input-amplitude-at-f-in-1-khz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 32. SNR vs. Input Amplitude at f_{IN} = 20 kHz](adaq4224/figures/adaq4224-f034.png)

*Figure 32. SNR vs. Input Amplitude at f_{IN} = 20 kHz*

Digitized data: [snr-vs-input-amplitude-at-f-in-20-khz.csv](adaq4224/curves/snr-vs-input-amplitude-at-f-in-20-khz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 33. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz, REFIN = 4.096 V](adaq4224/figures/adaq4224-f035.png)

*Figure 33. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz, REFIN = 4.096 V*

Digitized data: [snr-sinad-vs-input-amplitude-at-f-in-1-khz-refin-4-096-v.csv](adaq4224/curves/snr-sinad-vs-input-amplitude-at-f-in-1-khz-refin-4-096-v.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 34. SNR vs. Input Amplitude at f_{IN} = 50 kHz](adaq4224/figures/adaq4224-f036.png)

*Figure 34. SNR vs. Input Amplitude at f_{IN} = 50 kHz*

Digitized data: [snr-vs-input-amplitude-at-f-in-50-khz.csv](adaq4224/curves/snr-vs-input-amplitude-at-f-in-50-khz.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 35. SNR vs. Input Amplitude at f_{IN} = 100 kHz](adaq4224/figures/adaq4224-f037.png)

*Figure 35. SNR vs. Input Amplitude at f_{IN} = 100 kHz*

Digitized data: [snr-vs-input-amplitude-at-f-in-100-khz.csv](adaq4224/curves/snr-vs-input-amplitude-at-f-in-100-khz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 36. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz Single-Ended](adaq4224/figures/adaq4224-f038.png)

*Figure 36. SNR, SINAD vs. Input Amplitude at f_{IN} = 1 kHz Single-Ended*

Digitized data: [snr-sinad-vs-input-amplitude-at-f-in-1-khz-single-ended.csv](adaq4224/curves/snr-sinad-vs-input-amplitude-at-f-in-1-khz-single-ended.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 37. THD vs. Input Frequency, Various Amplitudes, G = 1/3](adaq4224/figures/adaq4224-f039.png)

*Figure 37. THD vs. Input Frequency, Various Amplitudes, G = 1/3*

Digitized data: [thd-vs-input-frequency-various-amplitudes-g-1-3.csv](adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-1-3.csv) (x: kHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 38. THD vs. Input Frequency, Various Amplitudes, G = 5/9](adaq4224/figures/adaq4224-f040.png)

*Figure 38. THD vs. Input Frequency, Various Amplitudes, G = 5/9*

Digitized data: [thd-vs-input-frequency-various-amplitudes-g-5-9.csv](adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-5-9.csv) (x: kHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 39. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 5 V](adaq4224/figures/adaq4224-f041.png)

*Figure 39. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 5 V*

Digitized data: [sfdr-vs-input-frequency-0-5-dbfs-refin-5-v.csv](adaq4224/curves/sfdr-vs-input-frequency-0-5-dbfs-refin-5-v.csv) (x: kHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 40. THD vs. Input Frequency, Various Amplitudes, G = 20/9](adaq4224/figures/adaq4224-f042.png)

*Figure 40. THD vs. Input Frequency, Various Amplitudes, G = 20/9*

Digitized data: [thd-vs-input-frequency-various-amplitudes-g-20-9.csv](adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-20-9.csv) (x: kHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 41. THD vs. Input Frequency, Various Amplitudes, G = 20/3](adaq4224/figures/adaq4224-f043.png)

*Figure 41. THD vs. Input Frequency, Various Amplitudes, G = 20/3*

Digitized data: [thd-vs-input-frequency-various-amplitudes-g-20-3.csv](adaq4224/curves/thd-vs-input-frequency-various-amplitudes-g-20-3.csv) (x: kHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 42. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 4.096 V](adaq4224/figures/adaq4224-f044.png)

*Figure 42. SFDR vs. Input Frequency, -0.5 dBFS, REFIN = 4.096 V*

Digitized data: [sfdr-vs-input-frequency-0-5-dbfs-refin-4-096-v.csv](adaq4224/curves/sfdr-vs-input-frequency-0-5-dbfs-refin-4-096-v.csv) (x: kHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 43. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V](adaq4224/figures/adaq4224-f045.png)

*Figure 43. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V*

Digitized data: [snr-sinad-vs-temperature-f-in-1-khz-differential-input-refin-5-v.csv](adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-differential-input-refin-5-v.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 44. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V](adaq4224/figures/adaq4224-f046.png)

*Figure 44. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V*

Digitized data: [snr-sinad-vs-temperature-f-in-1-khz-single-ended-input-refin-5-v.csv](adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-single-ended-input-refin-5-v.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 45. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V](adaq4224/figures/adaq4224-f047.png)

*Figure 45. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 5 V*

Digitized data: [thd-vs-temperature-f-in-1-khz-differential-input-refin-5-v.csv](adaq4224/curves/thd-vs-temperature-f-in-1-khz-differential-input-refin-5-v.csv) (x: °C; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 46. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V](adaq4224/figures/adaq4224-f048.png)

*Figure 46. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V*

Digitized data: [snr-sinad-vs-temperature-f-in-1-khz-differential-input-refin-4-096-v.csv](adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-differential-input-refin-4-096-v.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 47. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V](adaq4224/figures/adaq4224-f049.png)

*Figure 47. SNR, SINAD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V*

Digitized data: [snr-sinad-vs-temperature-f-in-1-khz-single-ended-input-refin-4-096-v.csv](adaq4224/curves/snr-sinad-vs-temperature-f-in-1-khz-single-ended-input-refin-4-096-v.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 48. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V](adaq4224/figures/adaq4224-f050.png)

*Figure 48. THD vs. Temperature, f_{IN} = 1 kHz Differential Input, REFIN = 4.096 V*

Digitized data: [thd-vs-temperature-f-in-1-khz-differential-input-refin-4-096-v.csv](adaq4224/curves/thd-vs-temperature-f-in-1-khz-differential-input-refin-4-096-v.csv) (x: °C; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 49. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V](adaq4224/figures/adaq4224-f051.png)

*Figure 49. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 5 V*

Digitized data: [thd-vs-temperature-f-in-1-khz-single-ended-input-refin-5-v.csv](adaq4224/curves/thd-vs-temperature-f-in-1-khz-single-ended-input-refin-5-v.csv) (x: °C; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 50. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 5 V](adaq4224/figures/adaq4224-f052.png)

*Figure 50. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 5 V*

Digitized data: [sfdr-vs-temperature-f-in-1-khz-refin-5-v.csv](adaq4224/curves/sfdr-vs-temperature-f-in-1-khz-refin-5-v.csv) (x: °C; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 51. Transition Noise vs. Temperature, REFIN = 5 V](adaq4224/figures/adaq4224-f053.png)

*Figure 51. Transition Noise vs. Temperature, REFIN = 5 V*

Digitized data: [transition-noise-vs-temperature-refin-5-v.csv](adaq4224/curves/transition-noise-vs-temperature-refin-5-v.csv) (x: °C; y: LSBrms) — values read off the printed plot by the digitizer, not published data.

![Figure 52. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V](adaq4224/figures/adaq4224-f054.png)

*Figure 52. THD vs. Temperature, f_{IN} = 1 kHz Single-Ended Input, REFIN = 4.096 V*

Digitized data: [thd-vs-temperature-f-in-1-khz-single-ended-input-refin-4-096-v.csv](adaq4224/curves/thd-vs-temperature-f-in-1-khz-single-ended-input-refin-4-096-v.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 53. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 4.096 V](adaq4224/figures/adaq4224-f055.png)

*Figure 53. SFDR vs. Temperature, f_{IN} = 1 kHz, REFIN = 4.096 V*

Digitized data: [sfdr-vs-temperature-f-in-1-khz-refin-4-096-v.csv](adaq4224/curves/sfdr-vs-temperature-f-in-1-khz-refin-4-096-v.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 54. Transition Noise vs. Temperature, REFIN = 4.096 V](adaq4224/figures/adaq4224-f056.png)

*Figure 54. Transition Noise vs. Temperature, REFIN = 4.096 V*

Digitized data: [transition-noise-vs-temperature-refin-4-096-v.csv](adaq4224/curves/transition-noise-vs-temperature-refin-4-096-v.csv) (x: °C; y: LSBrms) — values read off the printed plot by the digitizer, not published data.

![Figure 55. RMS Noise vs. Temperature, REFIN = 5 V](adaq4224/figures/adaq4224-f057.png)

*Figure 55. RMS Noise vs. Temperature, REFIN = 5 V*

Digitized data: [rms-noise-vs-temperature-refin-5-v.csv](adaq4224/curves/rms-noise-vs-temperature-refin-5-v.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 56. Offset Error vs. Temperature](adaq4224/figures/adaq4224-f058.png)

*Figure 56. Offset Error vs. Temperature*

Digitized data: [offset-error-vs-temperature.csv](adaq4224/curves/offset-error-vs-temperature.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 57. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 5 V](adaq4224/figures/adaq4224-f059.png)

*Figure 57. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 5 V*

Digitized data: [dynamic-range-vs-number-of-averages-input-60-dbfs-refin-5-v.csv](adaq4224/curves/dynamic-range-vs-number-of-averages-input-60-dbfs-refin-5-v.csv) (x: samples; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 58. RMS Noise vs. Temperature, REFIN = 4.096 V](adaq4224/figures/adaq4224-f060.png)

*Figure 58. RMS Noise vs. Temperature, REFIN = 4.096 V*

Digitized data: [rms-noise-vs-temperature-refin-4-096-v.csv](adaq4224/curves/rms-noise-vs-temperature-refin-4-096-v.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 59. Gain Error vs. Temperature](adaq4224/figures/adaq4224-f061.png)

*Figure 59. Gain Error vs. Temperature*

Digitized data: [gain-error-vs-temperature.csv](adaq4224/curves/gain-error-vs-temperature.csv) (x: °C; y: %FS) — values read off the printed plot by the digitizer, not published data.

![Figure 60. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 4.096 V](adaq4224/figures/adaq4224-f062.png)

*Figure 60. Dynamic Range vs. Number of Averages, Input = -60 dBFS, REFIN = 4.096 V*

Digitized data: [dynamic-range-vs-number-of-averages-input-60-dbfs-refin-4-096-v.csv](adaq4224/curves/dynamic-range-vs-number-of-averages-input-60-dbfs-refin-4-096-v.csv) (x: samples; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 61. Low Frequency Noise (Output Data Rate = 256 SPS After Averaging Blocks of 4096 Samples), REFIN = 5 V](adaq4224/figures/adaq4224-f063.png)

*Figure 61. Low Frequency Noise (Output Data Rate = 256 SPS After Averaging Blocks of 4096 Samples), REFIN = 5 V*

![Figure 62. AC CMRR vs. Input Frequency, REFIN = 5 V](adaq4224/figures/adaq4224-f064.png)

*Figure 62. AC CMRR vs. Input Frequency, REFIN = 5 V*

Digitized data: [ac-cmrr-vs-input-frequency-refin-5-v.csv](adaq4224/curves/ac-cmrr-vs-input-frequency-refin-5-v.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 63. Input Current vs. Input Voltage across Temperature](adaq4224/figures/adaq4224-f065.png)

*Figure 63. Input Current vs. Input Voltage across Temperature*

Digitized data: [input-current-vs-input-voltage-across-temperature.csv](adaq4224/curves/input-current-vs-input-voltage-across-temperature.csv) (x: V; y: pA) — values read off the printed plot by the digitizer, not published data.

![Figure 64. Low Frequency Noise (Output Data Rate = 256 SPS After Averaging Blocks of 4096 Samples), REFIN = 4.096 V](adaq4224/figures/adaq4224-f066.png)

*Figure 64. Low Frequency Noise (Output Data Rate = 256 SPS After Averaging Blocks of 4096 Samples), REFIN = 4.096 V*

![Figure 65. AC CMRR vs. Input Frequency, REFIN = 4.096 V](adaq4224/figures/adaq4224-f067.png)

*Figure 65. AC CMRR vs. Input Frequency, REFIN = 4.096 V*

Digitized data: [ac-cmrr-vs-input-frequency-refin-4-096-v.csv](adaq4224/curves/ac-cmrr-vs-input-frequency-refin-4-096-v.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 66. Input Bias Current vs. Temperature](adaq4224/figures/adaq4224-f068.png)

*Figure 66. Input Bias Current vs. Temperature*

Digitized data: [input-bias-current-vs-temperature.csv](adaq4224/curves/input-bias-current-vs-temperature.csv) (x: °C; y: pA) — values read off the printed plot by the digitizer, not published data.

![Figure 67. Reference Buffer Offset vs. Temperature](adaq4224/figures/adaq4224-f069.png)

*Figure 67. Reference Buffer Offset vs. Temperature*

Digitized data: [reference-buffer-offset-vs-temperature.csv](adaq4224/curves/reference-buffer-offset-vs-temperature.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 68. Operating Current PGA and FDA vs. Temperature](adaq4224/figures/adaq4224-f070.png)

*Figure 68. Operating Current PGA and FDA vs. Temperature*

Digitized data: [operating-current-pga-and-fda-vs-temperature.csv](adaq4224/curves/operating-current-pga-and-fda-vs-temperature.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 69. Operating Current PGA and FDA vs. Sample Rate](adaq4224/figures/adaq4224-f071.png)

*Figure 69. Operating Current PGA and FDA vs. Sample Rate*

Digitized data: [operating-current-pga-and-fda-vs-sample-rate.csv](adaq4224/curves/operating-current-pga-and-fda-vs-sample-rate.csv) (x: MSPS; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 70. REFIN Current Normal Operation vs. Temperature](adaq4224/figures/adaq4224-f072.png)

*Figure 70. REFIN Current Normal Operation vs. Temperature*

Digitized data: [refin-current-normal-operation-vs-temperature.csv](adaq4224/curves/refin-current-normal-operation-vs-temperature.csv) (x: °C; y: µA) — values read off the printed plot by the digitizer, not published data.

![Figure 71. Operating Current ADC vs. Temperature](adaq4224/figures/adaq4224-f073.png)

*Figure 71. Operating Current ADC vs. Temperature*

Digitized data: [operating-current-adc-vs-temperature.csv](adaq4224/curves/operating-current-adc-vs-temperature.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 72. Operating Current ADC vs. Sample Rate](adaq4224/figures/adaq4224-f074.png)

*Figure 72. Operating Current ADC vs. Sample Rate*

Digitized data: [operating-current-adc-vs-sample-rate.csv](adaq4224/curves/operating-current-adc-vs-sample-rate.csv) (x: MSPS; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 73. Standby Current PGA and FDA vs. Temperature](adaq4224/figures/adaq4224-f075.png)

*Figure 73. Standby Current PGA and FDA vs. Temperature*

Digitized data: [standby-current-pga-and-fda-vs-temperature.csv](adaq4224/curves/standby-current-pga-and-fda-vs-temperature.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 74. Shutdown Current vs. Temperature](adaq4224/figures/adaq4224-f076.png)

*Figure 74. Shutdown Current vs. Temperature*

Digitized data: [shutdown-current-vs-temperature.csv](adaq4224/curves/shutdown-current-vs-temperature.csv) (x: °C; y: µA) — values read off the printed plot by the digitizer, not published data.

![Figure 75. Power Dissipation vs. Throughput](adaq4224/figures/adaq4224-f077.png)

*Figure 75. Power Dissipation vs. Throughput*

Digitized data: [power-dissipation-vs-throughput.csv](adaq4224/curves/power-dissipation-vs-throughput.csv) (x: MSPS; y: mW) — values read off the printed plot by the digitizer, not published data.

![Figure 76. Standby Current ADC vs. Temperature](adaq4224/figures/adaq4224-f078.png)

*Figure 76. Standby Current ADC vs. Temperature*

Digitized data: [standby-current-adc-vs-temperature.csv](adaq4224/curves/standby-current-adc-vs-temperature.csv) (x: °C; y: µA) — values read off the printed plot by the digitizer, not published data.

![Figure 77. VIO Operating Current vs. Sample Rate](adaq4224/figures/adaq4224-f079.png)

*Figure 77. VIO Operating Current vs. Sample Rate*

Digitized data: [vio-operating-current-vs-sample-rate.csv](adaq4224/curves/vio-operating-current-vs-sample-rate.csv) (x: MSPS; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 78. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 5 V, All Gains](adaq4224/figures/adaq4224-f080.png)

*Figure 78. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 5 V, All Gains*

Digitized data: [input-common-mode-voltage-vs-differential-input-voltage-refin-5-v-all-gains.csv](adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-refin-5-v-all-gains.csv) (x: V; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 79. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 4.096 V, All Gains](adaq4224/figures/adaq4224-f081.png)

*Figure 79. Input Common-Mode Voltage vs. Differential Input Voltage, REFIN = 4.096 V, All Gains*

Digitized data: [input-common-mode-voltage-vs-differential-input-voltage-refin-4-096-v-all-gains.csv](adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-refin-4-096-v-all-gains.csv) (x: V; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 80. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Positive, All Gains](adaq4224/figures/adaq4224-f082.png)

*Figure 80. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Positive, All Gains*

Digitized data: [input-common-mode-voltage-vs-differential-input-voltage-vin-positive-all-gains.csv](adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-vin-positive-all-gains.csv) (x: V; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 81. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Negative, All Gains](adaq4224/figures/adaq4224-f083.png)

*Figure 81. Input Common-Mode Voltage vs. Differential Input Voltage, VIN = Negative, All Gains*

Digitized data: [input-common-mode-voltage-vs-differential-input-voltage-vin-negative-all-gains.csv](adaq4224/curves/input-common-mode-voltage-vs-differential-input-voltage-vin-negative-all-gains.csv) (x: V; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 82. AC PSRR vs. Frequency, VDD_FDA](adaq4224/figures/adaq4224-f084.png)

*Figure 82. AC PSRR vs. Frequency, VDD_FDA*

Digitized data: [ac-psrr-vs-frequency-vdd-fda.csv](adaq4224/curves/ac-psrr-vs-frequency-vdd-fda.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 83. AC PSRR vs. Frequency, V_{DDH}](adaq4224/figures/adaq4224-f085.png)

*Figure 83. AC PSRR vs. Frequency, V_{DDH}*

Digitized data: [ac-psrr-vs-frequency-v-ddh.csv](adaq4224/curves/ac-psrr-vs-frequency-v-ddh.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 84. AC PSRR vs. Frequency, VDD_5V](adaq4224/figures/adaq4224-f086.png)

*Figure 84. AC PSRR vs. Frequency, VDD_5V*

Digitized data: [ac-psrr-vs-frequency-vdd-5v.csv](adaq4224/curves/ac-psrr-vs-frequency-vdd-5v.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 85. AC PSRR vs. Frequency, VSS_FDA](adaq4224/figures/adaq4224-f087.png)

*Figure 85. AC PSRR vs. Frequency, VSS_FDA*

Digitized data: [ac-psrr-vs-frequency-vss-fda.csv](adaq4224/curves/ac-psrr-vs-frequency-vss-fda.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 86. AC PSRR vs. Frequency, V_{SSH}](adaq4224/figures/adaq4224-f088.png)

*Figure 86. AC PSRR vs. Frequency, V_{SSH}*

Digitized data: [ac-psrr-vs-frequency-v-ssh.csv](adaq4224/curves/ac-psrr-vs-frequency-v-ssh.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 87. FFT, Grounded Inputs REFIN = 5 V](adaq4224/figures/adaq4224-f089.png)

*Figure 87. FFT, Grounded Inputs REFIN = 5 V*

![Figure 88. FFT, Grounded Inputs REFIN = 4.096 V](adaq4224/figures/adaq4224-f090.png)

*Figure 88. FFT, Grounded Inputs REFIN = 4.096 V*

![Figure 89. Output Overdrive Recovery, IN = 1 kHz](adaq4224/figures/adaq4224-f091.png)

*Figure 89. Output Overdrive Recovery, IN = 1 kHz*

![Figure 90. Long Term Drift, Offset Error RTO, G = 1/3](adaq4224/figures/adaq4224-f092.png)

*Figure 90. Long Term Drift, Offset Error RTO, G = 1/3*

![Figure 91. Long Term Drift, Offset Error RTO, G = 5/9](adaq4224/figures/adaq4224-f093.png)

*Figure 91. Long Term Drift, Offset Error RTO, G = 5/9*

![Figure 92. Long Term Drift, Offset Error RTO, G = 20/9](adaq4224/figures/adaq4224-f094.png)

*Figure 92. Long Term Drift, Offset Error RTO, G = 20/9*

![Figure 93. Long Term Drift, Offset Error RTO, G = 20/3](adaq4224/figures/adaq4224-f095.png)

*Figure 93. Long Term Drift, Offset Error RTO, G = 20/3*

![Figure 94. AAF Frequency Response](adaq4224/figures/adaq4224-f096.png)

*Figure 94. AAF Frequency Response*

Digitized data: [aaf-frequency-response.csv](adaq4224/curves/aaf-frequency-response.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

### TERMINOLOGY
<!-- pages: 31-33 -->

### INTEGRAL NONLINEARITY ERROR (INL)
<!-- page: 31 -->

INL is the deviation of each individual code from a line drawn from negative full scale through positive full scale. The point used as negative full scale occurs ½ LSB before the first code transition. Positive full scale is defined as a level 1½ LSB beyond the last code transition. The deviation is measured from the middle of each code to the true straight line (see Figure 96).

### DIFFERENTIAL NONLINEARITY ERROR (DNL)
<!-- page: 31 -->

In an ideal ADC, code transitions are 1 LSB apart. DNL is the maximum deviation from this ideal value. It is often specified in terms of resolution for which no missing codes are guaranteed.

### OFFSET ERROR
<!-- page: 31 -->

Offset error is the difference between the ideal midscale voltage, 0 V, and the actual voltage producing the midscale output code, 0 LSB.

### GAIN ERROR
<!-- page: 31 -->

The first transition (from 100 ... 00 to 100 ... 01) occurs at a level ½ LSB above nominal negative full scale. The last transition (from 011 … 10 to 011 … 11) occurs for an analog voltage 1½ LSB below the nominal full scale. The gain error is the deviation of the difference between the actual level of the last transition and the actual level of the first transition from the difference between the ideal levels.

### LEAST SIGNIFICANT BIT (LSB)
<!-- page: 31 -->

The smallest increment that can be represented by a converter. For a fully differential input µModule with N bits of resolution, the LSB expressed in volts is:


$$ LSB(V)=(VREF×2)/2^N × AFE Gain $$


### SPURIOUS-FREE DYNAMIC RANGE (SFDR)
<!-- page: 31 -->

SFDR is the difference, in decibels relative to the carrier (dBc), between the rms amplitude of the input signal and the peak spurious signal.

### EFFECTIVE NUMBER OF BITS (ENOB)
<!-- page: 31 -->

ENOB is a measurement of the resolution with a sine wave input. It is related to SINAD as follows: ENOB = (SINADdB - 1.76)/6.02. ENOB is expressed in bits.

### TOTAL HARMONIC DISTORTION (THD)
<!-- page: 31 -->

THD is the ratio of the rms sum of the first five harmonic components to the rms value of the input signal and is expressed in decibels relative to the carrier (dBc).

### DYNAMIC RANGE
<!-- page: 31 -->

Dynamic range is the rms voltage of a full-scale sine wave to the total rms voltage of the noise measured. The value for dynamic range is expressed in decibels. It is measured with a signal at -60 dBFS so that it includes all noise sources and DNL artifacts.

### TOTAL SYSTEM DYNAMIC RANGE
<!-- page: 31 -->

The ratio of the root-mean-square (RMS) value of the full scale input at Gain = 1/3 V/V to the input referred RMS noise measured when input pins are shorted together at Gain = 20/3 V/V. The value is expressed in decibels.

### SIGNAL-TO-NOISE RATIO (SNR)
<!-- page: 31 -->

SNR is the ratio of the rms voltage of a full-scale sine wave to the rms sum of all other spectral components below the Nyquist frequency, excluding harmonics and DC. The value for SNR is expressed in decibels relative to the full scale (dBFS).

### SIGNAL-TO-NOISE-AND-DISTORTION (SINAD) RATIO
<!-- page: 31 -->

SINAD is the ratio of the rms voltage of a full-scale sine wave to the rms sum of all other spectral components that are less than the Nyquist frequency, including harmonics but excluding DC. The value of SINAD is expressed in decibels relative to the full scale (dBFS).

### TRANSITION NOISE
<!-- page: 31 -->

Transition noise is the noise generated when the µModule inputs are grounded or are connected to a precise voltage source. Transition noise is calculated as:

$$ Transition Noise (LSB) = RTI RMS Noise / LSB (V) $$

### APERTURE DELAY
<!-- page: 31 -->

Aperture delay is the measure of the acquisition performance and is the time between the rising edge of the CNV input and when the input signal is held for a conversion.

### TRANSIENT RESPONSE
<!-- page: 31 -->

Transient response is the time required for the µModule to acquire a full-scale input step to ±1 LSB accuracy.

### COMMON-MODE REJECTION RATIO (CMRR)
<!-- page: 31 -->

CMRR is the ratio of the power in the µModule output at the frequency, f, to the power of a 4.5 V p-p sine wave applied to the input common-mode voltage of frequency, f.

![Equation as printed (p. 31)](adaq4224/figures/adaq4224-eq02.png)

$$\mathit{CMRR}\ \text{(dB)} = 10\times \log(P_{\mu Module\_IN}/P_{\mu Module\_OUT})$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where:

PµModule\_OUT is the power at the frequency, f, in the µModule output.

PµModule\_IN is the common-mode power at the frequency, f, applied to the inputs.

### POWER-SUPPLY REJECTION RATIO (PSRR)
<!-- page: 31 -->

PSRR is the ratio of the power in the µModule output at the frequency, f, to the power of a 200 mV p-p sine wave applied to the

µModule supply (VDD\_5V, VDD\_FDA, VSS\_FDA, VDDH, VSSH) of frequency, f.

PSRR (dB) = 10 × log( PSUPPLY\_IN / PµModule\_OUT )

### where:

PSUPPLY\_IN is the power at the frequency, f, at the supply pin.
PµModule\_OUT is the power at the frequency, f, in the µModule output.


### THEORY OF OPERATION
<!-- pages: 33-39 -->

![Figure 95. ADAQ4224 Functional Block Diagram](adaq4224/figures/adaq4224-f097.png)

*Figure 95. ADAQ4224 Functional Block Diagram*

### OVERVIEW

The ADAQ4224 is a precision µModule data-acquisition signal chain SiP solution that reduces the development cycle of precision measurement systems by transferring the design burden of component selection, optimization, and layout from the designer to the device. The ADAQ4224 reduces the end system component count by combining multiple common signal processing and conditioning blocks in a single device, including a low noise, high input impedance PGIA, a second order linear phase anti-aliasing filter, low distortion, wide-bandwidth ADC driver, a high precision 24-bit, 2MSPS SAR ADC with an integrated reference buffer, and a fully-electrically isolated temperature sensor. The device also incorporates the Analog Devices proprietary iPassives technology components necessary for optimum performance. The superior matching and drift characteristics of the resistors minimizes the temperature dependent error sources. The analog front end of the ADAQ4224 features a wide common-mode range of -8 V to +10 V and supports both single-ended and differential signals that eases level shifting requirements as well.

The ADAQ4224 does not exhibit any pipeline delay or latency, which makes this µModule ideal for control loops and high speed applications. The digital features include offset correction, gain adjustment, and averaging, which offload the host processor. The user can configure the device for one of several output code formats (for more details, see the Summary of Selectable Output Data Formats section).

The ADAQ4224 uses a Flexi-SPI, which allows the data to be accessed by multiple SPI lanes, which relaxes clocking requirements for the host SPI controller. An echo clock mode is also available to assist in data clocking, which simplifies the use of isolated data interfaces. The PGIA gain of the ADAQ4224 can be controlled through A0 and A1 pins. The ADAQ4224 includes an electrically isolated temperature sensor, which has a 1.8 V, I^{2}C compatible interface. The leakage current between the temperature sensor ground (TMP\_GND) and ADC ground (GND) is 1 nA with ±250 V across the ground planes. The ADAQ4224 has a valid first conversion after exiting power-down mode. The architecture achieves ±1 ppm INL maximum, with no missing codes at 24-bits and 106.5 dB SNR. The ADAQ4224 dissipates only 446 mW at 2 MSPS.
### TRANSFER FUNCTION
<!-- page: 33 -->

In the default configuration, the ADAQ4224 digitizes the full-scale difference voltage of 2 × V_{REFIN} into 2^{24} levels, which results in an LSB size of 0.596 µV with V_{REFIN} = 5 V. Note that 1 LSB at 24 bits is approximately 0.06 ppm. The ideal transfer function is shown in Figure 96. The differential output data is in twos complement format. Table 13 summarizes the mapping of input voltages to differential output codes.

![Figure 96. ADC Ideal Transfer Function for the Differential Output Codes (FSR Is Full-Scale Range)](adaq4224/figures/adaq4224-f098.png)

*Figure 96. ADC Ideal Transfer Function for the Differential Output Codes (FSR Is Full-Scale Range)*


**Table 13. Input Voltage to Output Code Mapping** ([table-12-p34-data.csv](adaq4224/tables/table-12-p34-data.csv), p. 34)

| Description | Analog Input Voltage Difference | Digital Output Code (Twos Complement, Hex) |
|---|---|---|
| FSR − 1LSB | (8388607 × V_{REF})/(G × 8388608) | 0x7FFFFF |
| Midscale + 1LSB | V_{REF}/(G × 8388608) | 0x000001 |
| Midscale | 0 V | 0x000000 |
| Midscale − 1LSB | −V_{REF}/(G × 8388608) | 0xFFFFFF |
| −FSR + 1LSB | −(8388607 × V_{REF})/(G × 8388608) | 0x800001 |
| −FSR | −V_{REF}/G | 0x800000 |


### SIGNAL CHAIN OPERATION
<!-- page: 34 -->

The ADAQ4224 operates in two phases, the acquisition and the conversion phase. In the acquisition phase, the voltage present on each input pin (INP and INN) of PGIA is sampled independently. Issuing a rising edge pulse on the CNV pin initiates a conversion. The rising edge pulse on the CNV pin also asserts the BUSY signal to indicate a conversion in progress. At the end of the conversion, the BUSY signal is deasserted. The conversion result is a 24-bit code representing the input voltage difference and an 8-bit code representing the input common-mode voltage. Depending on the device configuration, this conversion result can be processed digitally and latched into the internal output register. The internal ADC acquisition circuit on each input pin is also precharged to the previous sample voltage, which minimizes the kick-back charge to the input driver stage (PGIA). The host processor retrieves the output code by the SDO pins that are internally connected to the internal output register.

### DIGITAL SAMPLE PROCESSING FEATURES
<!-- page: 34 -->


The ADAQ4224 supports several digital and data processing features that can be applied to the signal samples. These features are enabled and disabled by the control registers of the ADAQ4224.

### Full-Scale Saturation
<!-- page: 34 -->

The conversion results saturate digitally (before any post-processing) when either or both inputs exceed the analog limits specified herein. After applying offset and gain scaling, the results are reduced to 24-bit representation (saturating at maximum 0x7FFFFF and minimum 0x800000). A user must avoid unintentional saturation, especially, when applying digital offset and/or gain scaling. For more details on the use of these features, see the Digital Offset Adjust and Digital Gain sections.

### Common-Mode Output
<!-- page: 34 -->

When the host controller writes 0x1 or 0x2 to the OUT\_DATA\_MD bit field of the modes register (for more details, see the Modes Register section), an 8-bit code representing the input common-mode voltage is appended to the 16-bit or 24-bit code representing the input voltage difference. The LSB size of the 8-bit code is V_{REF} /256. The 8-bit code saturates at 0 and 255 when the common-mode input voltage is 0 V and V_{REF} , respectively. The 8-bit code is not affected by digital offset and gain scaling, which is applied only to the code representing the input voltage difference.

### Block Averaging
<!-- page: 34 -->

The ADAQ4224 provides a block averaging filter (SINC1) with programmable block length 2^{N}, N = 1, 2, 3, …, 16. The filter is reset after processing each block of 2^{N} samples. The filter is enabled by writing 0x3 to the OUT\_DATA\_MD bit field of the modes register (for more details, see the Modes Register section) as well as a value (1 ≤ N ≤ 16) to the AVG\_VAL bit field in the averaging mode register (for more details, see the Averaging Mode Register section). In this configuration, the output sample word is 32 bits. The 30 most significant bits (MSBs) represent the numerical value of the 24-bit codes averaged in blocks of 2^{N} samples. The automatic scaling allows the 24 MSBs of the 30-bit code to be equal to the 24-bit codes when averaging blocks of constant values. The 31^{st} bit (OR) is an overrange warning bit that is high when one or more samples in the block are subject to saturation. The 32^{nd} bit (SYNC) is high once every 2^{N} conversion cycles to indicate when the average values are updated at the end of each block of samples. For more details, see the Digital Sample Processing Features section.

The effective data rate in averaging mode is f_{CNV}/2^{N}. The reset value of N in the AVG\_VAL bit field is 0x00 (no averaging). Figure 120 shows an example timing diagram in averaging mode. Figure 97 shows the frequency response of the filter for an N = 1, 2, 3, 4, 5.

![Figure 97. Frequency Response Examples for the Block Averaging Filter](adaq4224/figures/adaq4224-f099.png)

*Figure 97. Frequency Response Examples for the Block Averaging Filter*

### Digital Offset Adjust
<!-- page: 34 -->

The ADC can be programmed to add a 24-bit signed offset value to the sample data (for more details, see the Register Details section). When adding an offset to the samples, it is possible to cause the sample data to saturate numerically. The user must take this into account when using the offset feature. The default value is 0x000000. For more details, see the Offset Registers section.

### Digital Gain
<!-- page: 34 -->

The ADC can be programmed to apply a 16-bit unsigned digital gain (Register 0x1C and Register 0x1D) to the digital samples (for more details, see the Register Details section). The gain is applied to each sample based on the following equation: 

$$ \textit{Code}_{\text{out}} = \textit{Code}_{\text{in}} \times (\text{USER\_GAIN}/0x8000) $$

where:

0x0000 ≤ USER\_GAIN ≤ 0xFFFF.

The effective gain range is 0 to 1.99997. Note that applying gain to the samples may cause numerical saturation. The default value is 0x8000 (gain = 1). To measure input voltage differences exceeding ±VREF , set the gain less than the unity to avoid the numerical saturation of the 24-bit, 16-bit, or 30-bit output differential codes. For more details, see the Gain Registers section.


### Test Pattern
<!-- page: 35 -->

To facilitate functional testing and debugging of the SPI, the host controller can write a 32-bit test pattern to the ADAQ4224 (for more details, see the Test Pattern Registers section). The value written to the test pattern registers is output using the normal sample cycle timing. The 32-bit test pattern output mode is enabled by writing 0x4 to the OUT\_DATA\_MD bit field of the modes register (for more details, see the Modes Register section). The default value stored in the test pattern registers is 0x5A5A0F0F.

### Summary of Selectable Output Data Formats
<!-- page: 35 -->

Figure 98 summarizes the output data formats that are available on the ADAQ4224, which are selected in the modes register (for more details, see the Modes Register section). Note that the OR and SYNC flags are each 1-bit.

![Figure 98. Summary of Selectable Output Sample Formats](adaq4224/figures/adaq4224-f100.png)

*Figure 98. Summary of Selectable Output Sample Formats*

### TEMPERATURE SENSOR OPERATION
<!-- page: 35 -->

The ADAQ4224 includes a temperature sensor that is electrically isolated from the data-acquisition signal path within the µModule. In applications, where the ADAQ4224 is isolated, the ground of the data-acquisition signal path can float to any voltage level (for example, 200 V) while the temperature sensor stays at ground and its digital input/output pins do not need to be isolated. The temperature sensor enables predictable drift measurement of complete data-acquisition signal path and simplifies system-level calibration of the signal path vs. temperature change. The 1.8 V, I^{2}C-compatible serial interface accepts standard write and read commands to read the temperature data and configure the behavior of the sensor. It offers 12-bit temperature measurements with excellent accuracy of ±1°C maximum from -40°C to +105°C. Multiple register settings allow a host to configure the temperature sensor for automatic temperature measurements, change the ALARM thresholds and hysteresis, and configure the polarity of the ALARM output. The temperature sensor includes an RSEL address pin, which can be connected to an external resistor to uniquely identify up to 32 devices connected on the same I^{2}C bus.

The temperature sensor provides 12-bit temperature measurements and asserts the ALARM output when the measured temperature is outside of the programmed range defined by the low and high temperature registers, TL and TH, respectively. The temperature data is also available to read by a host microcontroller using the I^{2}C bus. Multiple register settings allow a host to configure the part for automatic temperature measurements, change ALARM thresholds and hysteresis, and configure the polarity of the ALARM output.

### Measuring Temperature
<!-- page: 35 -->

A resolution of 8-, 9-, 10-, or 12-bits can be selected using the configuration register. 8-bit resolution corresponds to a least significant bit (LSB) value of +1°C, while 12-bit resolution corresponds to an LSB value of +0.0625°C. The sensor powers of up in a preconfigured state. For the default/power-up settings, see the Device Configuration Register section.


Digitized data: [frequency-response-examples-for-the-block-averaging-filter.csv](adaq4224/curves/frequency-response-examples-for-the-block-averaging-filter.csv) (x: f_{IN}/f_{S}; y: dB) — values read off the printed plot by the digitizer, not published data.


### Temperature Sensor Device Address
<!-- page: 36 -->

The temperature sensor employs an I^{2}C 7-bit addressing scheme. An external resistor connected to the RSEL pin is measured upon power up of the VDD pin. The value of the resistor defines the device address and the value can be used to identify up to 32 devices connected to the same I^{2}C bus. Mapping the address selection resistor value to Bits[A4:A0] is shown in Table 14. Connect the RSEL pin to TMP\_GND if only one device is used.

The upper two bits are fixed to the values 10. For example, a device that uses a value of 905 kΩ responds to the target address 1000000.

*Table 14. RSEL Resistor Selection of Device Address Bits[A4:A0]: the full table ([table-13-p36-data.csv](adaq4224/tables/table-13-p36-data.csv)) is rendered in this section.*


**Table 14. RSEL Resistor Selection of Device Address Bits[A4:A0]** ([table-13-p36-data.csv](adaq4224/tables/table-13-p36-data.csv), p. 36)

| Bits [A4:A0] | 1% Resistor Value (kΩ) | Bits [A4:A0] | 1% Resistor Value (kΩ) |
|---|---|---|---|
| 11111 | 4.2 | 01111 | 67.3 |
| 11110 | 5 | 01110 | 80 |
| 11101 | 5.9 | 01101 |  95.1 |
| 11100 | 7.1 | 01100 | 113.1 |
| 11011 | 8.4 | 01011 | 134.5 |
| 11010 | 10 | 01010 | 160 |
| 11001 | 11.9 | 01001 | 190.3 |
| 11000 | 14.1 | 01000 | 226.3 |
| 10111 | 16.8 | 00111 | 269.1 |
| 10110 | 20 | 00110 | 320 |
| 10101 | 23.8 | 00101 | 380.5 |
| 10100 | 28.3 | 00100 | 452.5 |
| 10011 | 33.6 | 00011 | 538.2 |
| 10010 | 40 | 00010 | 640 |
| 10001 | 47.6 | 00001 | 761.1 |
| 10000 | 56.6 | 00000 | 905.1 |

### Temperature Sensor Data
<!-- page: 36 -->

The temperature data format produces values up to and beyond the +105°C operating limit.

Table 15. Temperature/Data Relationship for 12-Bit Resolution

|                  | Data Format         | Data Format   |
|------------------|---------------------|---------------|
| Temperature (°C) | Binary              | Hexadecimal   |
| +150             | 0000 1001 0110 0000 | 0960h         |
| +128             | 0000 1000 0000 0000 | 0800h         |
| +125             | 0000 0111 1101 0000 | 07D0h         |
| +85              | 0000 0101 0101 0000 | 0550h         |
| +25.0625         | 0000 0001 1001 0001 | 0191h         |
| +10.125          | 0000 0000 1010 0010 | 00A2h         |
| +0.5             | 0000 0000 0000 1000 | 0008h         |
| 0                | 0000 0000 0000 0000 | 0000h         |
| -0.5             | 1111 1111 1111 1000 | FFF8h         |
| -10.125          | 1111 1111 1111 1000 | FFF8h         |
| -25.0625         | 1111 1110 0110 1111 | FE6Fh         |
| -55              | 1111 1100 1001 0000 | FC90h         |

**Table 16. Temperature Data Format (S = Sign Bit)** ([table-15-p36-data.csv](adaq4224/tables/table-15-p36-data.csv), p. 36)

| D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| **Most Significant Byte (°C)** |  |  |  |  |  |  |  |  |  |  |  |  |  | **Least Significant Byte (°C)**  |  |
| S | S | S | S | 128 | 64 | 32 | 16 | 8 | 4 | 2 | 1 | 0.5 | 0.25 | 0.125 | 0.0625 |

### Temperature Sensor Configuration and Status
<!-- page: 37 -->

### One Shot
<!-- page: 37 -->

The one-shot function helps to reduce the average supply current when continuous conversions are not necessary. Before setting this bit, the application needs to reset the Conversion Period bits. Writing a 1 to D0 while in shutdown mode immediately prompts a new temperature conversion. After the conversion is complete, the device returns to shutdown mode and D0 automatically resets. If needed, the host can check the status of the one-shot bit to detect when the conversion is complete. If the device is configured for automatic sampling mode, and a conversion is in progress at the time a one-shot command is issued, it waits for the current conversion to complete before starting a new sequence. If the part is in automatic sampling mode but a conversion is not in progress, the one-shot command starts immediately. The host is able to reset the automatic conversion period and set the one-shot bit using a single write command to the configuration/status register.

### Conversion Rate
<!-- page: 37 -->

The Conversion Rate bits, D3:D1, select the rate for automatic continuous conversions. Rates between 1 conversion/64 sec and 8 conversions/sec are available. The nominal conversion time is 35 ms at the default resolution of 10 bits. In automatic conversion mode, shutdown mode is entered between conversions to reduce the average power-supply current. Writing a value of 0b000 to this field causes the temperature sensor to enter shutdown mode. If a conversion is in progress at the time the value in this field is set to 0b000, the state of the machine allows the conversion to finish before entering shutdown.

**Table 17. Conversion Rate Selection** ([table-16-p37-register.csv](adaq4224/tables/table-16-p37-register.csv), p. 37)

| D3 | D2 | D1 | Conversion Rate |
|---|---|---|---|
| 0 | 0 | 0 | 0 (shutdown) |
| 0 | 0 | 1 | 1 conversion/64 second |
| 0 | 1 | 0 | 1 conversion/32 second |
| 0 | 1 | 1 | 1 conversion/16 second |
| 1 | 0 | 0 | 1 conversion/4 second |
| 1 | 0 | 1 | 1 conversion/second (default) |
| 1 | 1 | 0 | 4 conversion/second |
| 1 | 1 | 1 | 8 conversion/second |
### Packet Error Checking (PEC)
<!-- page: 37 -->

Set D4 to enable PEC. When enabled, a PEC byte is appended to the end of each message transfer. This is a CRC-8 byte that is calculated on all of the message bytes (including the address/read/ write byte). The last device to transmit a data byte also transmits the PEC byte. The controller transmits the PEC byte after a write transaction, and the temperature sensor transmits the PEC byte after a read transaction.

### Timeout

Write 1 to D5 to disable bus timeout. Write 0 to D5 to enable bus timeout. Bus timeout resets the I^{2}C-compatible interface when SCL is low for more than 30 ms (nominal).

### Resolution
<!-- page: 37 -->

The resolution bits (Bits[D7:D6]) select the conversion resolution. The conversion time doubles with every bit of increased resolution. For example, the nominal 10-bit conversion time is 35 ms. Increasing the resolution to 12 bits increases the conversion time to 140 ms. The resolution bits allow resolution, conversion time, and supply current to be optimized for the application's requirements. The bits in this field must only be changed when the temperature sensor is in shutdown mode.

**Table 18. Resolution Selection** ([table-17-p37-register.csv](adaq4224/tables/table-17-p37-register.csv), p. 37)

| D7 | D6 | Resolution |
|---|---|---|
| 0 | 0 | 8-bit |
| 0 | 1 | 9-bit |
| 1 | 0 | 10-bit |
| 1 | 1 | 12-bit (default) |

### ALARM Polarity
<!-- page: 37 -->

When D8 is 0, the ALARM active state is low. The ALARM output is driven low when the temperature is above TH or below TL. When D8 is 1, the ALARM active state is high. The ALARM pin is pulled high when the temperature is above TH or below TL. If the hysteresis thresholds are programmed, after a temperature alarm, the ALARM pin status changes when the temperature falls below TH\_HYST or above TL\_HYST. Note that the behavior for both settings is dependent on the Fault Queue setting. The ALARM pin is an open-drain output and requires a pull-up resistor to operate.

### Comparator and Interrupt
<!-- page: 37 -->

Set the D9 comparator and interrupt bit to 0 to make the overtemperature status (OT and UT status) bits operate in comparator mode. In comparator mode, the OT/UT status bits have a value of 1 when the temperature rises above the TH value or falls below TL, which is also subject to the fault queue selection. OT status returns to 0 when the temperature drops below the TH\_HYST value or when shutdown mode is entered. Similarly, UT status returns to 0 when the temperature rises above TL\_HYST value or when shutdown mode is entered.

Set bit D9 to 1 to operate OT/UT status bits in interrupt mode. Exceeding TH in this mode also sets OT status to 1, which remains set until a read operation is performed on the configuration/status register, at this point, it returns to 0. Once OT status is set to 1 from exceeding TH and reset, it is set to 1 again only when the temperature drops below TH\_HYST. The output remains asserted until it is reset by a read. It is set again if the temperature rises above TH, and so on. The same logic applies to the operation of the UT status bit.

Putting the temperature sensor into shutdown mode also resets the OT/UT status bits. Note that if the mode is changed while OT/UT status bits are set, an OT/UT status reset may be required before it begins to behave normally. To prevent this, it is recommended to perform a read of the configuration/status register to clear the status bits before changing the operating mode.

### Fault Queue
<!-- page: 37 -->

The fault queue bits (Bits[D11:D10]) select how many consecutive temperature faults must occur before overtemperature or undertemperature faults are TH indicated in the corresponding status bits. The fault queue selection applies to both comparator and interrupt modes. The fault queue counter resets any time the temperature falls below TH or rises above TL. The fault counter does not change when the measured temperature drops below TH\_HYST or is above TL\_HYST thresholds. In interrupt mode, clearing the fault conditions is done using an I^{2}C transaction by reading the configuration/status register. In comparator mode, the flags reset when the temperature measured is between TL\_HYST and TH\_HYST thresholds.

**Table 19. Fault Queue Selection** ([table-18-p38-register.csv](adaq4224/tables/table-18-p38-register.csv), p. 38)

| D11 | D10 | Number of Faults |
|---|---|---|
| 0 | 0 | 1 (default) |
| 0 | 1 | 2 |
| 1 | 0 | 4 |
| 1 | 1 | 8 |

### PEC Error
<!-- page: 38 -->

This bit is read-only. It is set to 1 by the device when the PEC enable bit is set. During an I^{2}C transaction, the PEC value calculated by the device does not match the value sent by the host. When the PEC enable bit is 0, it remains 0.

### Undertemperature Status
<!-- page: 38 -->

D14 is a read-only bit that indicates the temperature value is under the TL threshold. Its behavior is controlled by the comparator and interrupt and fault queue bits.

### Overtemperature Status
<!-- page: 38 -->

D15 is a read-only bit that indicates that the temperature value is exceeding the value in the TH register. Its behavior is controlled by the comparator and interrupt and fault queue bits.

### Temperature Threshold Alarm
<!-- page: 38 -->

Addresses 0x04 and 0x06 contain the 16-bit alarm thresholds, TH and TL. The default values for these registers are loaded at power up. The data format is the same as that of the temperature register. Once the part is powered up, the values can be changed using the I 2 C interface. The memory used to store the settings is volatile, and the content of the registers is not retained if the power is powered down.

Before the register values are changed over I^{2}C, the part must be in shutdown mode. For more details, see the Configuration and Status Register section. Operation in automatic mode can resume after the register update.

### Alarm Hysteresis Thresholds
<!-- page: 38 -->

Addresses 0x08 and 0x0A contain the 16-bit alarm hysteresis thresholds, TH\_HYST, and TL\_HYST. The default values for these registers are loaded at power up and depend on the part option selected. The data format is the same as that of the temperature register. Once the part is powered up, the values can be changed using the I^{2}C interface. The memory used to store the settings is volatile and the content of the registers is not stored upon power down.

TH\_HYST is intended to have values less than or equal to TH, and TL\_HYST value has to be equal of higher than TL for the part to operate correctly. Before the register values are changed over I^{2}C, the part must be in shutdown mode. For more details, see the Configuration and Status Register Conversion Rate field. Operation in automatic mode can resume after the register update.

### APPLICATIONS INFORMATION
<!-- pages: 39-47 -->

### TYPICAL APPLICATION DIAGRAM
<!-- page: 39 -->

Figure 99 shows the typical system-level block diagram of a floating voltmeter including power tree and digital isolators. Echo clock mode and controller clock mode relax the timing requirements and simplify the use of digital isolators. Figure 99 to Figure 107 shows the typical application examples of differential signals applied to each of the ADAQ4224 inputs for a given gain.

![Figure 99. Functional Block Diagram of a Fully Isolated Data-Acquisition System](adaq4224/figures/adaq4224-f101.png)

*Figure 99. Functional Block Diagram of a Fully Isolated Data-Acquisition System*

![Figure 100. Differential Input Configuration with G = 1/3 V/V](adaq4224/figures/adaq4224-f102.png)

*Figure 100. Differential Input Configuration with G = 1/3 V/V*

![Figure 101. Differential Input Configuration with G = 5/9 V/V](adaq4224/figures/adaq4224-f103.png)

*Figure 101. Differential Input Configuration with G = 5/9 V/V*

![Figure 102. Differential Input Configuration with G = 20/9 V/V](adaq4224/figures/adaq4224-f104.png)

*Figure 102. Differential Input Configuration with G = 20/9 V/V*

![Figure 103. Differential Input Configuration with G = 20/3 V/V](adaq4224/figures/adaq4224-f105.png)

*Figure 103. Differential Input Configuration with G = 20/3 V/V*

![Figure 104. Single-Ended Input Configuration with G = 1/3 V/V](adaq4224/figures/adaq4224-f106.png)

*Figure 104. Single-Ended Input Configuration with G = 1/3 V/V*

![Figure 105. Single-Ended Input Configuration with G = 5/9 V/V](adaq4224/figures/adaq4224-f107.png)

*Figure 105. Single-Ended Input Configuration with G = 5/9 V/V*

![Figure 106. Single-Ended Input Configuration with G = 20/9 V/V](adaq4224/figures/adaq4224-f108.png)

*Figure 106. Single-Ended Input Configuration with G = 20/9 V/V*

![Figure 107. Single-Ended Input Configuration with G = 20/3 V/V](adaq4224/figures/adaq4224-f109.png)

*Figure 107. Single-Ended Input Configuration with G = 20/3 V/V*

### REFERENCE CIRCUITRY DESIGN
<!-- page: 44 -->

The ADAQ4224 requires an external reference to define its input range. This reference must be within 4.096 V to 5 V. The optimal choice for a 4.096 V reference is the ADR4540 or the LTC6655LN-4.096, for a 5 V, use the ADR4550 reference or the LTC6655LN-5. The µModule has several features that reduce the charge pulled from the reference, which makes the ADAQ4224 much easier to use than the discrete implementations. The external reference is connected to the REFIN pin, which has an internal precision buffer that isolates the reference from the µModule circuitry. The buffer has a high-input impedance and draws a small input current (5 nA typical). The REFIN pin is also connected a 500 kΩ voltage divider that generates the VOCM of the ADC driver, which draws an input current (10 µA typical). An internal 2 µF capacitor on the output of the buffer provides optimal reference bypassing and simplifies PCB design by reducing component count and layout sensitivity. An RC circuit between the reference and the REFIN pin can be used to filter reference noise (see Figure 108). Suggested values are 100 Ω < R < 1 kΩ, and C ≥ 10 µF.

In applications where a burst of samples is taken after idling for long periods, as shown in Figure 109, the reference current (I_{REF} ) changes from approximately 10 µA to about 12 µA at 2 MSPS. This step in DC current draw triggers a transient response in the reference that must be considered because any deviation in the reference output voltage affects the accuracy of the output code. If the reference is driving the REFIN pins, the internal buffer is able to handle these transitions.

![Figure 108. Reference with Noise Filter](adaq4224/figures/adaq4224-f110-01.png)

*Figure 108. Reference with Noise Filter*

![Figure 109. CNV Waveform Showing Burst Sampling](adaq4224/figures/adaq4224-f110-02.png)

*Figure 109. CNV Waveform Showing Burst Sampling*

### ADC RESET
<!-- page: 45 -->

The ADAQ4224 provides two options for performing an ADC reset using the serial interface. A hardware reset is initiated by pulsing the voltage on the RST pin low. A software reset is initiated by setting both the SW\_RESET and SW\_RESETX bits in the Interface Configuration A register to 1 in the same write instruction (for more details, see the Interface Configuration A Register section).

Performing a hardware or software reset asserts the RESET\_OC-CURRED bit in the digital diagnostics register (for more details, see the Digital Diagnostics Register section). The RESET\_OCCURRED bit is cleared by writing the bit with a 1. RESET\_OCCURRED can be used by the digital host to confirm that the ADAQ4224 has executed a device reset.

The ADAQ4224 is designed to generate a power-on reset (POR) when VDD\_5V and VDD\_1.8V are first applied. A POR resets the state of the user configuration registers and asserts the RE-SET\_OCCURRED bit. If VDD\_5V or VDD\_1.8V drops below its specified operating range, a POR occurs. It is recommended to perform a hardware or software reset after a POR.

Figure 110 shows the timing diagram for performing an ADC reset using the RST input. The minimum RST pulse width is 50 ns, represented by t RESET\_PW in Figure 110 and Table 1. A reset must be performed no sooner than 3 ms after the power supplies are valid and stable (this delay is represented by t RESET\_DELAY in Figure 110 and Table 1).

After a hardware or software reset, no SPI commands or conversions can be started for 750 µs.

![Figure 110. Power-On Reset (POR) Timing](adaq4224/figures/adaq4224-f111.png)

*Figure 110. Power-On Reset (POR) Timing*

### POWER SUPPLIES
<!-- page: 45 -->

The recommended power-up sequence for the supply pins of the ADAQ4224 is shown in Figure 111. The recommended sequence is to power up the PGIA (VDDH and VSSH) first, then the FDA (VDD\_FDA and VSS\_FDA) along with the supplies of the ADC (VDD\_5V, VLDO, and VIO), then bring up the reference voltage (REFIN) and lastly turn on the input signal at INP and INN pins. A user must adhere to the maximum voltage relationships described in the Absolute Maximum Ratings section.

![Figure 111. Power Supply Sequence](adaq4224/figures/adaq4224-f112.png)

*Figure 111. Power Supply Sequence*
TIME

The voltage range for the VDD\_5V supply depends on the chosen reference voltage (see the parameter Internal Reference Buffer in Table 1). Figure 112 shows the minimum and maximum values for VDD\_5V with respect to REFIN. VDD\_5V voltage values above the maximum or below the minimum result in either damage to the device or degraded performance.

![Figure 112. VDD_5V Minimum and Maximum Values for REFIN](adaq4224/figures/adaq4224-f113.png)

*Figure 112. VDD_5V Minimum and Maximum Values for REFIN*

The ADAQ4224 has a POR circuit that resets the ADAQ4224 at initial power-up or whenever VDD\_5V or VDD\_1.8V drops below its specified operating range.

Note that the VDD\_5V and the VLDO supplies have internal 1 µF bypass capacitors inside the package, VIO has an internal 0.2 µF bypass capacitor, while the VDDH, VSSH, VDD\_FDA, VSS\_FDA, and VDD have an internal 0.1 µF bypass capacitor. These internal capacitors reduce BOM count and solution size. If the bulk-supply bypass capacitors are not close to the ADC, add external capacitors next to the ADC. The minimum rise time for all supplies is 100 µs.

Digitized data: [vdd-5v-minimum-and-maximum-values-for-refin.csv](adaq4224/curves/vdd-5v-minimum-and-maximum-values-for-refin.csv) (x: ; y: V) — values read off the printed plot by the digitizer, not published data.

### Power Consumption States
<!-- page: 46 -->

During a conversion, the power consumption of the ADAQ4224 is at its highest. When the conversion is complete, it enters a standby state and much of the internal circuitry is powered down, and current consumption drops to less than 20% relative to the conversion state. To ensure full accuracy, some circuitry, including the reference buffer, remains powered on during the standby state.

The device can be placed into a lower power shutdown state during periods when the convert clock is idle by writing 0x3 to the OPERATING\_MODES bit field of the device configuration register (for more details, see the Device Configuration Register section). The default value of this bit field is [00] for normal operating mode. In the shutdown state, the current consumption typically drops to less than 10 µA.

### Shutdown Mode
<!-- page: 46 -->

When the ADC enters shutdown mode, the internal reference buffer is disabled and a 500 Ω switch connects REFIN to the output of the internal reference buffer. The which keeps the 2 µF capacitor on the output of the internal buffer charged up to allow fast recovery when the ADC exits shutdown mode. Because of this keep-alive switch, there is some charge injected to the REFIN pin when the ADC enters shutdown mode (400 pC) and exits shutdown mode (5 pC). When leaving shutdown mode, the output of the internal buffer is accurate after 30 µs.

### SERIAL INTERFACE
<!-- pages: 47-58 -->

The ADAQ4224 supports a multilane SPI serial digital interface with a common bit clock (SCK). The flexible VIO pins supply allows the ADAQ4224 to communicate with any digital logic operating between 1.2 V and 1.8 V. However, for the VIO pins levels less than 1.4 V, the IO2X bit in the output driver register must be set to 1 (for more details, see the Output Driver Register section). The serial output data is clocked out on up to 4 SDO lanes (see Figure 113). An echo clock mode that is synchronous with the output data is available to ease timing requirements when using isolation on the digital interface. A host clock mode is also available and uses an internal oscillator to clock out the data bits. The SPI Clocking Mode, Echo Clock Mode, Host Clock Mode, Single-Data Rate Mode, Dual-Data Rate Mode, 1-Lane Output Data Clocking Mode, 2-Lane Output Data Clocking Mode, 4-Lane Output Data Clocking Mode, and Data Output Modes Summary sections describe the operation of the ADAQ4224 SPI.

The default communication mode upon power up is 1-Lane Mode, SPI Mode, SDR mode, and 24-bit differential data.


![Figure 113. ADAQ4224 Multilane SPI](adaq4224/figures/adaq4224-f114.png)

*Figure 113. ADAQ4224 Multilane SPI*

### SPI SIGNALS
<!-- page: 47 -->

The SPI is a multilane interface that is used to both configure the ADC as well as retrieve sampled data. It consists of the following signals:

- CS (input) (chip select). CS must be set to low to initiate and enable a data transfer to or from the SDI pins or SDOx pins of the ADC. CS timing for reading sample data can be moderated by observing the state of the BUSY pin. For echo clock mode and host clock mode, CS timing must be controlled by the host processor because the BUSY\_SCKOUT pin is used as the bit clock output for these clocking modes.
- SDI (input). Serial data input stream from the host controller to the ADC. The SDI signal is only used when writing data into one of the user registers of the ADAQ4224.
- CNV (input). The CNV signal is sourced by the host controller and initiates a sample conversion. The frequency of the CNV signal determines the sampling rate of the ADAQ4224. The maximum frequency of the CNV clock is 2 MSPS.
- SCK (input). Serial data clock sourced by the host controller. The maximum SCK rate supported for output data transfer is 100 MHz. For register reads and writes, the maximum SCK rate is 86 MHz for the VIO pins > 1.71 V, and 81 MHz for 1.14 V ≤ the VIO pins < 1.71 V.
- SDO0 through SDO3 (outputs). Data lanes to the host controller. The number of active data lanes can be either 1-lane, 2-lane, or 4-lane (see Table 21). The number of data lanes is configured in the Modes Register section.
- BUSY\_SCKOUT (output). The behavior of the BUSY\_SCKOUT pin is dependent on the selected clocking mode. Table 20 defines the behavior of the BUSY\_SCKOUT pin for each clocking mode.

**Table 20. BUSY_SCKOUT Pin Behavior vs. Clocking Mode** ([table-19-p47-data.csv](adaq4224/tables/table-19-p47-data.csv), p. 47)

| Clocking Mode | Behavior |
|---|---|
| SPI Clocking Mode | Valid BUSY_SCKOUT pin signal for the ADC conversion status. The busy signal on the BUSY_SCKOUT pin goes high when a conversion is triggered by the CNV signal. The busy signal on the BUSY_SCKOUT pin goes low when the conversion is complete. |
| Echo Clock Mode | Bit clock. The BUSY_SCKOUT pin is a delayed version of SCK input. |
| Host Clock Mode | Bit clock. The BUSY_SCKOUT pin sources the clock signal from the internal oscillator. |

### Register Access Mode
<!-- page: 47 -->

The ADAQ4224 offers programmable user registers that are used to configure the device, as shown in the Registers section. By default, the device is in conversion mode during power-up. Therefore, to access the user registers, a special access command must be sent by the host controller over the SPI, as shown in Figure 5. When this register access command is sent over the SPI, the device enters the register configuration mode. To readback the values from one of the user registers listed in the Registers section, the host controller must send the pattern shown in Figure 4. To write to one of the user registers, the host controller must send the pattern shown in Figure 3. In either case (read/write), the host controller must always issue 24 clock pulses on SCK line and pull CS low for the entire transaction.

After writing to/reading from the appropriate user registers, the host controller must exit the register configuration mode by writing 0x01 to register address 0x0014 as detailed in the EXIT Configuration Mode Register section. An algorithm for register read/write access is as follows:

1. Perform a readback from a dummy register address 0x3FFF, to enter the register configuration mode.
2. Readback from or write to the required user register addresses.
3. Exit the register configuration mode by writing 0x01 to register address 0x0014. Exiting register configuration mode causes the register updates to take effect.

### Stream Mode
<!-- page: 48 -->

The ADAQ4224 also offers a way to perform bulk register read/write transactions while the ADAQ4224 is in register configuration mode. To perform bulk read/write registers transactions, CS must be kept low and SCK pulses must be issued in multiples of 8 as each register is only one byte (8 bits) wide. In stream mode, only address decrementing is allowed, which means that the user can read back from/write to the initial register address and register addresses that are directly below the initial register address. It is recommended that register accesses in stream mode be applied to register blocks with contiguous addresses. However, it is possible to address registers that are not present in the register map. To do so, simply write all zeros to these registers, or, when reading back, simply discard the contents read from these registers since it is random data. To see which register address is valid and continuous, see the Registers section. For example, to readback a 24-bit offset value in one shot, the user must issue 24 SCK pulses starting from Register Address 0x0018. Figure 114 shows timing diagram for bulk read starting at a given address.

![Figure 114. Stream Mode Bulk Register Readback Operation](adaq4224/figures/adaq4224-f115.png)

*Figure 114. Stream Mode Bulk Register Readback Operation*

### SAMPLE CONVERSION TIMING AND DATA TRANSFER
<!-- page: 49 -->

A conversion is started on the rising edge of the CNV signal, as shown in Figure 115. Once the conversion is complete, CS can be asserted, which causes the current conversion result to be loaded into the output shift register.

As shown in Figure 115, there are two optional data transfer zones for sample N. Zone 1 represents the use case where CS is asserted immediately following the deassertion of BUSY signal for the sample N conversion (in SPI conversion mode), or after 300 ns for echo and host clock modes. For Zone 1, the available time to read out sample N is given by:

Zone 1 Data Read Window
 $$ = t_{CYC} - t_{CONV} - t_{QUIET\, CNV\_ADV} $$
 
 For example, if F CNV is 2 MSPS (t_{CYC} = 500 ns) and using the typical value of t_{CONV} (282 ns), the available window width is 198.4 ns (= 500 ns - 282 ns - 19.6 ns).

Zone 2 represents the case where assertion of CS to read sample N is delayed until after the conversion for sample N+1 has been initiated.

To prevent data corruption, a quiet zone must be observed before and after each rising edge of the CNV signal, as shown in Figure 115. The quiet zone immediately before the rising edge of CNV is labeled as t_{QUIET_CNV_ADV} , and is equal to 19.6 ns. The quiet zone immediately after the rising edge of CNV is labeled t_{QUIET_CNV_DE-LAY} , and is equal to 9.8 ns. Assuming that the CS is asserted immediately after the quiet zone around the rising edge of CNV, the amount of time available to clock out the data is:

Zone 2 Data Read Window
$$ = t_{CYC} - t_{QUIET\_CNV\_DELAY} - t_{QUIET\_CNV\_ADV} $$

For example, if F CNV is 2 MSPS (t_{CYC} = 500 ns) and using the typical value of t_{CONV} (282 ns), the available window width is 470.6 ns (= 500 ns - 9.8 ns - 19.6 ns). The Zone 2 transfer window is longer than the Zone 1 window. This can enable the use of a slower SCK on the SPI and ease the timing requirements for the interface. When using Zone 2 for the data transfer, it is recommended to assert CS immediately after the quiet zone. However, it must be asserted at least 25 ns before the falling edge of BUSY for sample N+1. If not, then sample N is overwritten with sample N+1.

![Figure 115. Example Timing for Data Transfer Zones](adaq4224/figures/adaq4224-f116.png)

*Figure 115. Example Timing for Data Transfer Zones*

### CLOCKING MODES
<!-- page: 50 -->

This section covers the various clocking modes supported by the ADAQ4224 SPI. These modes are available for 1-lane, 2-lane, and 4-lane. The clocking mode is configured in the modes register (for register descriptions, see Table 23).

### SPI Clocking Mode
<!-- page: 50 -->

SPI clocking mode is the default clocking mode of the ADAQ4224 and is equivalent to a host-sourced bit clock (SCK), in which the host controller uses its own clock to latch the output data. The SPIcompatible clocking mode is enabled by writing 0x0 to the CLK\_MD bit field of the modes register (for more details, see the Modes Register section). The interface connection is shown in Figure 113. In this mode, the BUSY\_SCKOUT pin signal is valid and indicates that the completion of a conversion (high-to-low transition of the BUSY\_SCKOUT pin). A simplified sample cycle is shown in Figure 116. When not in averaging mode, if the host controller does not use the BUSY\_SCKOUT pin signal to detect the completion of a conversion and instead uses an internal timer to retrieve the data, the host controller must wait at least 300 ns after the rising edge of the CNV pulse before asserting CS low. When operating in block averaging mode, the host controller must assert CS low no sooner than 300 ns after the rising edge of the CNV pulse for the last sample in the block.

![Figure 116. Typical Sample Cycle for SPI Clocking Mode](adaq4224/figures/adaq4224-f117.png)

*Figure 116. Typical Sample Cycle for SPI Clocking Mode*

### Echo Clock Mode
<!-- page: 51 -->

Figure 117 shows the signal connections for the echo clock mode. The echo clock mode is enabled by writing 0x1 to the CLK\_MD bit field of the modes register (for more details, see the Modes Register section). In this mode, the BUSY\_SCKOUT pin cannot be used to detect a conversion completion. The BUSY\_SCKOUT pin becomes a bit clock output and is sourced by looping through the SCK of the host controller to the BUSY\_SCKOUT pin (with some fixed delay, 5.4 ns to 7.9 ns, which depends on the voltage of the VIO pins). To begin retrieving the conversion data in nonaveraging mode, the host controller must assert CS low no sooner than 300 ns after the rising edge of the CNV pulse. When the ADC is configured for block averaging mode, the host controller must assert CS low no sooner than 300 ns after the rising edge of the CNV pulse for the last sample in the block. Example timing diagrams are shown in the Data Clocking Requirements and Timing section. When echo clock mode is enabled, the BUSY\_SCKOUT pin is aligned with the SDOx pins transitions, which makes the data and clock timing insensitive to asymmetric propagation delays in the paths of the SDOx pins and SCK pins.

![Figure 117. Echo Clock Mode Signal Path Diagram](adaq4224/figures/adaq4224-f118.png)

*Figure 117. Echo Clock Mode Signal Path Diagram*
### Host Clock Mode
<!-- page: 51 -->

When enabled, host clock mode uses the internal oscillator as the bit clock source. The host clock mode is enabled by writing 0x2 to the CLK\_MD bit field of the modes register. The bit clock frequency can be programmed in the OSC\_DIV bit field in the internal oscillator register, with available divisor values of 1, 2, or 4 (for more details, see the Internal Oscillator Register section). Figure 118 shows the signal connections for the host clock mode. In this mode, the BUSY\_SCKOUT pin provides the bit clock output and cannot be used to detect a conversion completion. The ADAQ4224 automatically calculates the number of clock pulses required to clock out the conversion data based on word size, number of active lanes, and choice of single-data rate mode or dual-data rate mode. The number of clock pulses can be read from the OSC\_LIMIT bit field of the internal oscillator register. The SCK\_IN from the host must not be active. When retrieving the conversion data in nonaveraging mode, the host must not assert CS low sooner than 300 ns after the rising edge of the CNV pulse. When the ADC is configured in averaging mode for 2^{N} averages, the host must not assert CS low sooner than 300 ns after the rising edge of the CNV pulse for the last sample in the block.

![Figure 118. Host Clock Mode Signal Path Example](adaq4224/figures/adaq4224-f119.png)

*Figure 118. Host Clock Mode Signal Path Example*
### Single-Data Rate Mode
<!-- page: 51 -->

Single-data rate clocking (SDR), in which one bit (per active lane) is clocked out during a single clock cycle, is supported for all output configurations and sample formats (see Table 21). The SDR clocking mode is enabled by default at power-up or can be enabled by writing 0 to the DDR\_MD bit of the modes register (for more details, see the Modes Register section).

### Dual-Data Rate Mode
<!-- page: 51 -->

Dual-data rate (DDR) mode (two data bit transitions per clock cycle per active lane) is available only for host clock mode and echo clock mode.

The DDR clocking mode is enabled by writing 1 to the DDR\_MD bit of the modes register (for more details, see the Modes Register section). The DDR mode uses half the number of SCK pulses to clock out conversion data in comparison to SDR mode.

### 1-Lane Output Data Clocking Mode
<!-- page: 51 -->

1-lane is the default output data clocking mode at power-up. The 1-lane output data clocking mode is enabled by writing 0x0 to the LANE\_MD bit of the modes register (for more details, see the Modes Register section). The active lane is SDO0. Example timing diagrams for 1-lane mode using SPI clocking mode, echo clock mode, and host clock mode are shown in the Data Clocking Requirements and Timing section.

### 2-Lane Output Data Clocking Mode
<!-- page: 51 -->

When 2-lane output data clocking mode is enabled, the sample word bits are split between two SDO lanes. Figure 124 shows how the bits are allocated between the lanes for 2-lane mode. The bit arrangement is the same for SPI clock mode, echo clock mode, and host clock mode. A 2-lane output data clocking mode is enabled by writing 0x1 to the LANE\_MD bit of the modes register (for more details, see the Modes Register section). The host controller must recombine the data coming from the SDO lanes to reconstruct the original sample word. The number of SCK pulses required to clock out the conversion data is reduced by one-half with respect to the 1-lane mode. Table 21 lists the active SDO lanes for 2-lane mode. Example timing diagrams for 2-lane mode using SPI clock mode, echo clock mode, and host clock mode are shown in the Data Clocking Requirements and Timing section.

### 4-Lane Output Data Clocking Mode
<!-- page: 52 -->

When 4-lane output data clocking mode is enabled, the sample word bits are split between four SDO lanes. Figure 125 shows how the bits are allocated between the lanes for 4-lane mode. The bit arrangement is the same for SPI clock mode, echo clock mode, and host clock mode. A 4-lane output data clocking mode is enabled by writing 0x2 to the LANE\_MD bit of the modes register (for more details, see the Modes Register section). The host controller must recombine the data coming from the SDO lanes to reconstruct the original sample word. The number of SCK pulses required to clock out the conversion data is reduced by one-fourth with respect to the 1-lane output data clocking. The active SDO lanes for 4-lane mode are shown in Table 21. Example timing diagrams for 4-lane mode using SPI clock mode, echo clock mode, and host clock mode are shown in the Data Clocking Requirements and Timing section.

### Data Output Modes Summary
<!-- page: 52 -->

Table 21 is a summary of the supported data output modes of the ADAQ4224.

**Table 21. ADAQ4224 Supported Data Output Modes** ([table-20-p52-data.csv](adaq4224/tables/table-20-p52-data.csv), p. 52)

| Number of Lanes | Active SDO Lanes | Clock Mode | Supported Data Clocking Mode | Output Sample Data-Word Length |
|---|---|---|---|---|
| 1 | SDO0 | SPI | SDR only | 24 or 32 |
| 1 | SDO0 | Echo | SDR and DDR | 24 or 32 |
| 1 | SDO0 | Host | SDR and DDR | 24 or 32 |
| 2 | SDO0, SDO1 | SPI | SDR only | 24 or 32 |
| 2 | SDO0, SDO1 | Echo | SDR and DDR | 24 or 32 |
| 2 | SDO0, SDO1 | Host | SDR and DDR | 24 or 32 |
| 4 | SDO0, SDO1, SDO2, SDO3 | SPI | SDR only | 24 or 32 |
| 4 | SDO0, SDO1, SDO2, SDO3 | Echo | SDR and DDR | 24 or 32 |
| 4 | SDO0, SDO1, SDO2, SDO3 | Host | SDR and DDR | 24 or 32 |

### DATA CLOCKING REQUIREMENTS AND TIMING
<!-- page: 52 -->

### Basic and Averaging Conversion Cycles
<!-- page: 53 -->

Figure 119 shows the basic conversion cycle for a single sample. This cycle applies to SPI clocking mode. When using echo clock mode and host clock mode, the BUSY\_SCKOUT pin function is disabled and the bit clock is sourced on the BUSY\_SCKOUT pin. The data transfer must meet the requirements described in the Sample Conversion Timing and Data Transfer section.

Table 22 contains the minimum and maximum values for the conversion timing parameters, which apply to all clocking modes.

**Table 22. Conversion Cycle Timing Parameters** ([table-21-p53-spec.csv](adaq4224/tables/table-21-p53-spec.csv), p. 53)

| PARAMETER | MIN | MAX |
|---|---|---|
| t_{CNVH} | 10 ns | No specific maximum |
| t_{CNVL} | 20 ns | No specific maximum |
| t_{CONV} | 264 ns | 300 ns |

The duration of the data transfer period is dependent on the sample resolution, number of active lanes, SCK frequency, and data clocking mode (SDR or DDR). The nominal value of the transfer duration is given by:

![Equation as printed (p. 53)](adaq4224/figures/adaq4224-eq03.png)

$$ \\ \quad \ Data \, \ Transfer \, \ Duration = t_{TRANS} = \frac{N_{BITS}}{M_{LANES}} \\ \times \frac{1}{f_{SCK}} \times \frac{1}{K} \, \ seconds$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where:

NBITS = number of bits to clock out.  

MLANES = number of lanes used to clock out the data (1, 2, or 4). f_{SCK} = SCK clock frequency, in Hz.

K = 1 (SDR only, DDR not available for SPI mode clocking).

For a given f_{SCK} , number of data lanes, sample word size, and SDR/DDR mode, the minimum sample period when using Zone 1 for the data transfer is as follows:

![Equation as printed (p. 53)](adaq4224/figures/adaq4224-eq04.png)

$$ t_{CYC} \geq \left( \frac{N_{BITS}}{M_{LANES} \times f_{SCK} \times K} \right) + t_{CONV} + t_{QUIET\_CNV\_ADV} $$

The minimum sample period when using Zone 2 for data transfer is as follows:

![Equation as printed (p. 53)](adaq4224/figures/adaq4224-eq05.png)

$$ t_{CYC} \geq \left( \frac{N_{BITS}}{M_{LANES} \times f_{SCK} \times K} \right) + t_{QUIET\_CNV\_DELAY} + t_{QUIET\_CNV\_ADV}  $$
Figure 120 shows a typical conversion cycle when the averaging mode is active and SPI clocking mode is used. The BUSY signal is asserted for a number of CNV clock periods that is equal to the configured number of samples to be averaged. The averaged sample is then available when the BUSY signal is de-asserted. Similar to non-averaged mode, if the configured clocking mode is either echo clock or host clock, the BUSY signal is replaced by the output bit clock (SCKOUT). The host controller must manage the timing for asserting C̅S̅.

![Figure 119. Basic Single Sample Conversion Cycle](adaq4224/figures/adaq4224-f120.png)

*Figure 119. Basic Single Sample Conversion Cycle*

![Figure 120. Example Conversion Cycle for Averaging Mode](adaq4224/figures/adaq4224-f121.png)

*Figure 120. Example Conversion Cycle for Averaging Mode*

The two transfer zones that exist in nonaveraging mode also exist in averaging mode (see Figure 121, Figure 122, and Figure 123).

To prevent data corruption, it is necessary to avoid SPI rising and falling edges signals taking place during quiet zones.


![Figure 121. Example of Different Zones in Averaging Mode (64 Samples Averaged)](adaq4224/figures/adaq4224-f122.png)

*Figure 121. Example of Different Zones in Averaging Mode (64 Samples Averaged)*

![Figure 122. Example of Zone 2 in Averaging Mode (1 Bit per Sample)](adaq4224/figures/adaq4224-f123.png)

*Figure 122. Example of Zone 2 in Averaging Mode (1 Bit per Sample)*

![Figure 123. Example of Zone 2 in Averaging Mode (N Bits per Cycle)](adaq4224/figures/adaq4224-f124.png)

*Figure 123. Example of Zone 2 in Averaging Mode (N Bits per Cycle)*

### SPI Clocking Mode Timing Diagrams
### 1-Lane, SDR Mode
<!-- page: 55 -->

Figure 6 shows a conversion cycle for 1-lane data output, SDR clocking mode (1-bit per clock cycle).

### 2-Lane, SDR Mode
<!-- page: 55 -->

Figure 124 shows a conversion cycle for 2-lane data output using SDR clocking mode. For more details, see the 2-Lane Output Data Clocking Mode section.

![Figure 124. 2-Lane Mode, SDR Timing Diagram](adaq4224/figures/adaq4224-f125.png)

*Figure 124. 2-Lane Mode, SDR Timing Diagram*

### 4-Lane, SDR Mode
<!-- page: 56 -->

Figure 125 shows a conversion cycle for 4-lane data output using SDR clocking mode. For more details, see the 4-Lane Output Data Clocking Mode section.

![Figure 125. 4-Lane, SDR Timing Diagram](adaq4224/figures/adaq4224-f126.png)

*Figure 125. 4-Lane, SDR Timing Diagram*

### Echo Clock Timing Diagrams
<!-- page: 57 -->

### 1-Lane, SDR Mode, Echo Clock Mode
<!-- page: 57 -->

Figure 7 shows the timing relationships for SDR mode (1-bit per SCK period) in 1-lane echo clock mode. The timing relationships between the signals apply to both 24-bit and 32-bit sample word formats.

SCKOUT is a delayed version of the incoming SCK. The delay (t_{DSDO} ) has a maximum value of 5.6 ns (at V_{IO} > 1.71 V). Changes in SDOx logic states are aligned to the rising edges of SCKOUT. The clock and data edge alignments are the same for 1-lane, 2-lane, and 4-lane output data modes.

### 1-Lane, DDR Mode, Echo Clock Mode
<!-- page: 57 -->

Figure 8 shows the timing relationships for DDR mode (2-bit transitions per SCKOUT period) in 1-lane mode echo clock mode. The timing relationships between the signals apply to both 24-bit and 32-bit sample word formats.

Similar to SDR mode, SCKOUT is a delayed version of the incoming SCK. Changes in SDOx logic states are aligned to both rising and falling edges of SCKOUT.

### Host Clock Mode Timing
<!-- page: 57 -->

### 1-Lane, Host Clock Mode, SDR
<!-- page: 57 -->

Figure 9 shows the timing relationships for host clock mode when using SDR mode and 1-lane output data clocking mode. Similar to echo clock mode, the clock rising edges are aligned to the data bit transitions. The frequency of SCKOUT signal is controlled by the OSC\_DIV value programmed in the internal oscillator register (for more details, see the Internal Oscillator Register section).

### 1-Lane, Host Clock Mode, DDR
<!-- page: 57 -->

Figure 10 shows the timing relationships for host clock mode when using DDR mode. Similar to echo clock mode, the rising and falling clock edges are aligned to the data bit transitions. The frequency of SCKOUT signal is controlled by the OSC\_DIV value programmed in the internal oscillator register (for more details, see the Internal Oscillator Register section).

### LAYOUT GUIDELINES
<!-- pages: 58-59 -->

The following layout guidelines are recommended to achieve maximum performance of the ADAQ4224:

- The ADAQ4224 contains internal 1 µF bypass capacitors for VDD\_5V and VDD\_1.8V, and VIO contains an internal 0.2 µF capacitor. Therefore, no external bypass capacitors are required. This saves the board space and reduces the bill of materials (BOM) count and layout sensitivity.
- It is recommended to have all the analog signals flow in from the left side of the ADAQ4224 and all the digital signals to flow in and out from the right side of the ADAQ4224 because to help isolate analog signals from digital signals.
- Use a solid ground plane under the ADAQ4224 and connect all the analog ground (GND) pins and digital ground (IOGND) pins to the shared ground plane to avoid formation of ground loops.
- Traces routed to the REFIN pin must be isolated and shielded from other signals. Avoid routing signals beneath the reference trace (REFIN). If a noise reduction filter is placed between the output of the reference (or buffer) and the chosen reference input, it must be placed as close as possible to the ADAQ4224.

### REGISTERS
<!-- pages: 59-60 -->

The ADAQ4224 has programmable user registers that are used to configure the device. These registers can be accessed while the ADAQ4224 is in register configuration mode. Table 23 shows the complete list of the ADAQ4224 user registers and bit fields in the registers. The Register Details section shows the functions of each of the bit fields. The access mode specifies whether the register is comprised only of read-only bits (R) or a mix of read-only and read/write bits (R/W). Read-only bits cannot be overwritten by an SPI write transaction, but read/write bits can.

**Table 23. ADAQ4224 Register Summary** ([table-22-p59-register.csv](adaq4224/tables/table-22-p59-register.csv), p. 59)

| Reg | Name | Bits | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 | Reset | R/W |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 0x00 | INTERFACE_CONFIG_A | [7:0] | SW_RESET | RESERVED | ADDR_ASCENSION | SDO_ENABLE | RESERVED | RESERVED | RESERVED | SW_RESETX | 0x10 | R/W |
| 0x01 | INTERFACE_CONFIG_B | [7:0] | SINGLE_INST | STALLING | RESERVED | RESERVED | SHORT_INSTRUCTION | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x02 | DEVICE_CONFIG | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | OPERATING_MODES | OPERATING_MODES | 0x00 | R/W |
| 0x03 | CHIP_TYPE | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CHIP_TYPE | CHIP_TYPE | CHIP_TYPE | CHIP_TYPE | 0x07 | R |
| 0x04 | PRODUCT_ID_L | [7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | 0x00 | R |
| 0x05 | PRODUCT_ID_H | [7:0] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | 0x20 | R |
| 0x06 | CHIP_GRADE | [7:0] | GRADE | GRADE | GRADE | GRADE | GRADE | DEVICE_REVISION | DEVICE_REVISION | DEVICE_REVISION | 0x00 | R |
| 0x0A | SCRATCH_PAD | [7:0] | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | 0x00 | R/W |
| 0x0B | SPI_REVISION | [7:0] | SPI_TYPE | SPI_TYPE | VERSION | VERSION | VERSION | VERSION | VERSION | VERSION | 0x81 | R |
| 0x0C | VENDOR_L | [7:0] | VID[7:0] | VID[7:0] | VID[7:0] | VID[7:0] | VID[7:0] | VID[7:0] | VID[7:0] | VID[7:0] | 0x56 | R |
| 0x0D | VENDOR_H | [7:0] | VID[15:8] | VID[15:8] | VID[15:8] | VID[15:8] | VID[15:8] | VID[15:8] | VID[15:8] | VID[15:8] | 0x04 | R |
| 0x0E | STREAM_MODE | [7:0] | LOOP_COUNT | LOOP_COUNT | LOOP_COUNT | LOOP_COUNT | LOOP_COUNT | LOOP_COUNT | LOOP_COUNT | LOOP_COUNT | 0x00 | R/W |
| 0x11 | INTERFACE_STATUS_A | [7:0] | RESERVED | RESERVED | RESERVED | CLOCK_COUNT_ERR | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x14 | EXIT_CFG_MD | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | EXIT_CONFIG_MD | 0x00 | R/W |
| 0x15 | AVG | [7:0] | AVG_SYNC | RESERVED | RESERVED | AVG_VAL | AVG_VAL | AVG_VAL | AVG_VAL | AVG_VAL | 0x00 | R/W |
| 0x16 | OFFSET_LB | [7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | USER_OFFSET[7:0] | 0x00 | R/W |
| 0x17 | OFFSET_MB | [7:0] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | USER_OFFSET[15:8] | 0x00 | R/W |
| 0x18 | OFFSET_HB | [7:0] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | USER_OFFSET[23:16] | 0x00 | R/W |
| 0x19 | UNUSED1_LB | [7:0] | UNUSED1[7:0] | UNUSED1[7:0] | UNUSED1[7:0] | UNUSED1[7:0] | UNUSED1[7:0] | UNUSED1[7:0] | UNUSED1[7:0] | UNUSED1[7:0] | 0x00 | R/W |
| 0x1A | UNUSED1_MB | [7:0] | UNUSED1[15:8] | UNUSED1[15:8] | UNUSED1[15:8] | UNUSED1[15:8] | UNUSED1[15:8] | UNUSED1[15:8] | UNUSED1[15:8] | UNUSED1[15:8] | 0x00 | R/W |
| 0x1B | UNUSED1_HB | [7:0] | UNUSED1[23:16] | UNUSED1[23:16] | UNUSED1[23:16] | UNUSED1[23:16] | UNUSED1[23:16] | UNUSED1[23:16] | UNUSED1[23:16] | UNUSED1[23:16] | 0x00 | R/W |
| 0x1C | GAIN_LB | [7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | USER_GAIN[7:0] | 0x00 | R/W |
| 0x1D | GAIN_HB | [7:0] | USER_GAIN[15:8] | USER_GAIN[15:8] | USER_GAIN[15:8] | USER_GAIN[15:8] | USER_GAIN[15:8] | USER_GAIN[15:8] | USER_GAIN[15:8] | USER_GAIN[15:8] | 0x80 | R/W |
| 0x1E | UNUSED2_LB | [7:0] | UNUSED2[7:0] | UNUSED2[7:0] | UNUSED2[7:0] | UNUSED2[7:0] | UNUSED2[7:0] | UNUSED2[7:0] | UNUSED2[7:0] | UNUSED2[7:0] | 0x00 | R/W |
| 0x1F | UNUSED2_HB | [7:0] | UNUSED2[15:8] | UNUSED2[15:8] | UNUSED2[15:8] | UNUSED2[15:8] | UNUSED2[15:8] | UNUSED2[15:8] | UNUSED2[15:8] | UNUSED2[15:8] | 0x80 | R/W |
| 0x20 | MODES | [7:0] | LANE_MD | LANE_MD | CLK_MD | CLK_MD | DDR_MD | OUT_DATA_MD | OUT_DATA_MD | OUT_DATA_MD | 0x00 | R/W |
| 0x21 | OSCILLATOR | [7:0] | OSC_LIMIT | OSC_LIMIT | OSC_LIMIT | OSC_LIMIT | OSC_DIV | OSC_DIV | OSC_DIV | OSC_DIV | 0x00 | R/W |
| 0x22 | IO | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | IO2X | 0x00 | R/W |
| 0x23 | TEST_PAT_BYTE0 | [7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | TEST_DATA_PAT[7:0] | 0x0F | R/W |
| 0x24 | TEST_PAT_BYTE1 | [7:0] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | TEST_DATA_PAT[15:8] | 0x0F | R/W |
| 0x25 | TEST_PAT_BYTE2 | [7:0] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | TEST_DATA_PAT[23:16] | 0x5A | R/W |
| 0x26 | TEST_PAT_BYTE3 | [7:0] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | TEST_DATA_PAT[31:24] | 0x5A | R/W |
| 0x34 | DIG_DIAG | [7:0] | POWERUP_COMPLETED | RESET_OCCURRED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | FUSE_CRC_EN | 0x40 | R/W |
| 0x35 | DIG_ERR | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | FUSE_CRC_ERR | 0x00 | R/W |

### REGISTER DETAILS
<!-- pages: 60-69 -->

### INTERFACE CONFIGURATION A REGISTER
<!-- page: 60 -->

Address: 0x00, Reset: 0x10, Name: INTERFACE\_CONFIG\_A

Interface configuration settings.


![register bitfield (p. 60)](adaq4224/figures/adaq4224-f127.png)

**Table 24. Bit Descriptions for INTERFACE_CONFIG_A** ([table-23-p60-register.csv](adaq4224/tables/table-23-p60-register.csv), p. 60)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | SW_RESET | One of two of SW_RESET bits. This bit appears in two locations in this register. Both locations must be written at the same time to trigger a software reset of the part. All registers except for this register are reset to their default values. | 0x0 | R/W |
| 6 | RESERVED | Reserved. | 0x0 | R |
| 5 | ADDR_ASCENSION | Determines sequential addressing behavior. 0: Address accessed is decremented by one for each data byte when streaming. 1: Not a valid option. | 0x0 | R |
| 4 | SDO_ENABLE | SDO Pin Enable. | 0x1 | R |
| [3:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | SW_RESETX | Two of two of SW_RESET bits. This bit appears in two locations in this register. Both locations must be written at the same time to trigger a software reset of the part. All registers except for this register are reset to their default values. | 0x0 | R/W |

### INTERFACE CONFIGURATION B REGISTER
<!-- page: 60 -->

Address: 0x01, Reset: 0x00, Name: INTERFACE\_CONFIG\_B

Additional interface configuration settings.

![register bitfield (p. 60)](adaq4224/figures/adaq4224-f128.png)


**Table 25. Bit Descriptions for INTERFACE_CONFIG_B** ([table-24-p60-register.csv](adaq4224/tables/table-24-p60-register.csv), p. 60)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | SINGLE_INST | Select streaming or single instruction mode. 0: Streaming mode is enabled. The address decrements as successive data bytes are received. 1: Single instruction mode is enabled. | 0x0 | R/W |
| 6 | STALLING | Reserved for Stalling Feature. | 0x0 | R/W |
| [5:4] | RESERVED | Reserved. | 0x0 | R |
| 3 | SHORT_INSTRUCTION | Set the instruction phase address to 7 bits or 15 bits. 0: 15-bit addressing. 1: 7-bit addressing. | 0x0 | R |
| [2:0] | RESERVED | Reserved. | 0x0 | R |


### DEVICE CONFIGURATION REGISTER
<!-- page: 61 -->

Address: 0x02, Reset: 0x00, Name: DEVICE\_CONFIG

![register bitfield (p. 61)](adaq4224/figures/adaq4224-f129.png)

**Table 26. Bit Descriptions for DEVICE_CONFIG** ([table-25-p61-register.csv](adaq4224/tables/table-25-p61-register.csv), p. 61)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:2] | RESERVED | Reserved. | 0x0 | R |
| [1:0] | OPERATING_MODES | Power modes. 00: Normal operating mode. 11: Shutdown mode. | 0x0 | R/W |

### CHIP TYPE REGISTER
<!-- page: 61 -->

### Address: 0x03, Reset: 0x07, Name: CHIP\_TYPE
<!-- page: 61 -->

The chip type is used to identify the family of Analog Devices products a given device belongs to. Use the chip type with the product ID to uniquely identify a given product.

![register bitfield (p. 61)](adaq4224/figures/adaq4224-f130.png)

**Table 27. Bit Descriptions for CHIP_TYPE** ([table-26-p61-register.csv](adaq4224/tables/table-26-p61-register.csv), p. 61)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:4] | RESERVED | Reserved. | 0x0 | R |
| [3:0] | CHIP_TYPE | Precision ADC. | 0x7 | R |

### PRODUCT ID LOW REGISTER
<!-- page: 61 -->

Address: 0x04, Reset: 0x00, Name: PRODUCT\_ID\_L

Low byte of the product ID.

![register bitfield (p. 61)](adaq4224/figures/adaq4224-f131.png)


**Table 28. Bit Descriptions for PRODUCT_ID_L** ([table-27-p61-register.csv](adaq4224/tables/table-27-p61-register.csv), p. 61)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | PRODUCT_ID[7:0] | This is the device chip type/family. Use the product ID with the chip type to identify a product. | 0x0 | R |

### PRODUCT ID HIGH REGISTER
<!-- page: 61 -->

Address: 0x05, Reset: 0x20, Name: PRODUCT\_ID\_H

High byte of the product ID.

![register bitfield (p. 61)](adaq4224/figures/adaq4224-f132.png)

### Table 29. Bit Descriptions for PRODUCT\_ID\_H
<!-- page: 62 -->

**Table 29. Bit Descriptions for PRODUCT_ID_H** ([table-28-p62-register.csv](adaq4224/tables/table-28-p62-register.csv), p. 62)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | PRODUCT_ID[15:8] | This is the device chip type/family. Use the product ID with the chip type to identify a product. | 0x20 | R |

### CHIP GRADE REGISTER
<!-- page: 62 -->

Address: 0x06, Reset: 0x81, Name: CHIP\_GRADE

Identifies product variations and device revisions.

### Table 30. Bit Descriptions for CHIP\_GRADE
<!-- page: 62 -->

![register bitfield (p. 62)](adaq4224/figures/adaq4224-f133.png)

**Table 30. Bit Descriptions for CHIP_GRADE** ([table-29-p62-register.csv](adaq4224/tables/table-29-p62-register.csv), p. 62)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:3] | GRADE | This is the device performance grade. ADAQ4224: 0b11100. | 0x1C | R |
| [2:0] | DEVICE_REVISION | This is the device hardware revision. | 0x1 | R |

### SCRATCH PAD REGISTER
<!-- page: 62 -->

Address: 0x0A, Reset: 0x00, Name: SCRATCH\_PAD

This register can be used to test writes and reads.

![register bitfield (p. 62)](adaq4224/figures/adaq4224-f134.png)

### Table 31. Bit Descriptions for SCRATCH\_PAD
<!-- page: 62 -->

**Table 31. Bit Descriptions for SCRATCH_PAD** ([table-30-p62-register.csv](adaq4224/tables/table-30-p62-register.csv), p. 62)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | SCRATCH_VALUE | Software Scratchpad. Software can write to and read from this location without any device side effects. | 0x0 | R/W |

### SPI REVISION REGISTER
<!-- page: 62 -->

Address: 0x0B, Reset: 0x81, Name: SPI\_REVISION

Indicates the SPI revision.

![register bitfield (p. 62)](adaq4224/figures/adaq4224-f135.png)

**Table 32. Bit Descriptions for SPI_REVISION** ([table-31-p62-register.csv](adaq4224/tables/table-31-p62-register.csv), p. 62)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:6] | SPI_TYPE | Always reads as 0x2. | 0x2 | R |
| [5:0] | VERSION | SPI Version. | 0x1 | R |


### VENDOR ID LOW REGISTER
<!-- page: 63 -->

Address: 0x0C, Reset: 0x56, Name: VENDOR\_L

Low byte of the vendor ID.

![register bitfield (p. 63)](adaq4224/figures/adaq4224-f136.png)

**Table 33. Bit Descriptions for VENDOR_L** ([table-32-p63-register.csv](adaq4224/tables/table-32-p63-register.csv), p. 63)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | VID[7:0] | Analog Devices Vendor ID. | 0x56 | R |

### VENDOR ID HIGH REGISTER
<!-- page: 63 -->

Address: 0x0D, Reset: 0x04, Name: VENDOR\_H

High byte of the vendor ID.

![register bitfield (p. 63)](adaq4224/figures/adaq4224-f137.png)

**Table 34. Bit Descriptions for VENDOR_H** ([table-33-p63-register.csv](adaq4224/tables/table-33-p63-register.csv), p. 63)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | VID[15:8] | Analog Devices Vendor ID. | 0x4 | R |

### STREAM MODE REGISTER
<!-- page: 63 -->

Address: 0x0E, Reset: 0x00, Name: STREAM\_MODE

Defines the length of the loop when streaming data.

[7:0] LOOP\_COUNT (R/W) Sets the Data Byte Count Before Looping to Start Address

**Table 35. Bit Descriptions for STREAM_MODE** ([table-34-p63-register.csv](adaq4224/tables/table-34-p63-register.csv), p. 63)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | LOOP_COUNT | Sets the data byte count before looping to start address. Not enabled in the ADAQ4224. | 0x0 | R/W |

### INTERFACE STATUS A REGISTER
<!-- page: 63 -->

Address: 0x11, Reset: 0x00, Name: INTERFACE\_STATUS\_A

Status bits are set to 1 to indicate an active condition. The status bits can be cleared by writing a 1 to the corresponding bit location.

![register bitfield (p. 63)](adaq4224/figures/adaq4224-f138.png)

**Table 36. Bit Descriptions for INTERFACE_STATUS_A** ([table-35-p63-register.csv](adaq4224/tables/table-35-p63-register.csv), p. 63)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:5] | RESERVED | Reserved. | 0x0 | R |
| 4 | CLOCK_COUNT_ERR | 0 = No error. 1 = Incorrect Number of Clocks Detected in a Transaction. Write 1 to clear. | 0x0 | R/W1C |
| [3:0] | RESERVED | Reserved. | 0x0 | R |

### EXIT CONFIGURATION MODE REGISTER
<!-- page: 64 -->

Address: 0x14, Reset: 0x00, Name: EXIT\_CFG\_MD

![register bitfield (p. 64)](adaq4224/figures/adaq4224-f140.png)

**Table 37. Bit Descriptions for EXIT_CFG_MD** ([table-36-p64-register.csv](adaq4224/tables/table-36-p64-register.csv), p. 64)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | EXIT_CONFIG_MD | Exit Register Config Mode. Write 1 to exit register config mode. Self clearing upon C̅S̅ = 1. | 0x0 | R/W |

### AVERAGING MODE REGISTER
<!-- page: 64 -->

Address: 0x15, Reset: 0x00, Name: AVG

![register bitfield (p. 64)](adaq4224/figures/adaq4224-f141.png)

**Table 38. Bit Descriptions for AVG** ([table-37-p64-register.csv](adaq4224/tables/table-37-p64-register.csv), p. 64)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | AVG_SYNC | Averaging Filter Reset. 1 = Reset, self clearing. | 0x0 | R/W |
| [6:5] | RESERVED | Reserved. | 0x0 | R |
| [4:0] | AVG_VAL | Averaging Filter Frame Length, 2^{N}. 0x00 = No averaging. Use only 0x01 through 0x10 for averaging mode. 0x01 = 2^{1} samples. 0x02 = 2^{2} samples. 0x03 = 2^{3} samples. 0x04 = 2^{4} samples. 0x05 = 2^{5} samples. … 0x0F = 2^{15} samples. 0x10 = 2^{16} samples. 0x11 through 0x1F = Invalid. | 0x0 | R/W |

### OFFSET REGISTERS
<!-- page: 64 -->

Address: 0x16, Reset: 0x00, Name: OFFSET\_LB

![register bitfield (p. 64)](adaq4224/figures/adaq4224-f142.png)

**Table 39. Bit Descriptions for OFFSET_LB** ([table-38-p65-register.csv](adaq4224/tables/table-38-p65-register.csv), p. 65)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | USER_OFFSET[7:0] | 24-Bit Offset. Twos complement (signed). $$ 1 LSB = \frac{V_{REF}}{2^{23}} / GAIN.$$ | 0x0 | R/W |


**Address: 0x17, Reset: 0x00, Name: OFFSET\_MB**

![register bitfield (p. 65)](adaq4224/figures/adaq4224-f143.png)

**Table 40. Bit Descriptions for OFFSET_MB** ([table-39-p65-register.csv](adaq4224/tables/table-39-p65-register.csv), p. 65)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | USER_OFFSET[15:8] | 24-Bit Offset. Twos complement (signed). $$ 1 LSB = \frac{V_{REF}}{2^{23}} / GAIN.$$  | 0x0 | R/W |

**Address: 0x18, Reset: 0x00, Name: OFFSET\_HB**

![register bitfield (p. 65)](adaq4224/figures/adaq4224-f144.png)


**Table 41. Bit Descriptions for OFFSET_HB** ([table-40-p65-register.csv](adaq4224/tables/table-40-p65-register.csv), p. 65)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | USER_OFFSET[23:16] | 24-Bit Offset. Twos complement (signed). $$ 1 LSB = \frac{V_{REF}}{2^{23}} / GAIN.$$  | 0x0 | R/W |

### GAIN REGISTERS
<!-- page: 65 -->

**Address: 0x1C, Reset: 0x00, Name: GAIN\_LB**

![register bitfield (p. 65)](adaq4224/figures/adaq4224-f145.png)

**Table 42. Bit Descriptions for GAIN_LB** ([table-41-p65-register.csv](adaq4224/tables/table-41-p65-register.csv), p. 65)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | USER_GAIN[7:0] | Gain Word (Unsigned). Multiplier output = input × gain word/0x8000. Maximum effective gain = 0xFFFF/0x8000 = 1.99997. | 0x0 | R/W |

**Address: 0x1D, Reset: 0x80, Name: GAIN\_HB**

![register bitfield (p. 65)](adaq4224/figures/adaq4224-f146.png)

**Table 43. Bit Descriptions for GAIN_HB** ([table-42-p66-register.csv](adaq4224/tables/table-42-p66-register.csv), p. 66)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | USER_GAIN[15:8] | Gain Word (Unsigned). Multiplier output = input × gain word/0x8000. Maximum effective gain = 0xFFFF/0x8000 = 1.99997. | 0x80 | R/W |


### MODES REGISTER
<!-- page: 66 -->

**Address: 0x20, Reset: 0x00, Name: MODES**

![register bitfield (p. 66)](adaq4224/figures/adaq4224-f147.png)

**Table 44. Bit Descriptions for MODES** ([table-43-p66-register.csv](adaq4224/tables/table-43-p66-register.csv), p. 66)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:6] | LANE_MD | Lane Mode Select. 00 = One lane. 01 = Two lanes. 10 = Four lanes. 11 = Invalid setting. | 0x0 | R/W |
| [5:4] | CLK_MD | Clock Mode Select. 00 = SPI clocking mode. 01 = Echo clock mode. 10 = Host clock mode. 11 = Invalid setting. | 0x0 | R/W |
| 3 | DDR_MD | DDR Mode Enable/Disable. 0 = SDR. 1 = DDR (only valid for echo clock mode and host clock mode). | 0x0 | R/W |
| [2:0] | OUT_DATA_MD | Output Data Mode Select. 000 = 24-bit differential data. 001 = 16-bit differential data + 8-bit common-mode data. 010 = 24-bit differential data + 8-bit common-mode data. 011 = 30-bit averaged differential data + OR bit + SYNC bit. 100 = 32-bit test data pattern (TEST_DATA_PAT). | 0x0 | R/W |

### INTERNAL OSCILLATOR REGISTER
<!-- page: 66 -->

**Address: 0x21, Reset: 0x00, Name: OSCILLATOR**

![register bitfield (p. 66)](adaq4224/figures/adaq4224-f148.png)

**Table 45. Bit Descriptions for OSCILLATOR** ([table-44-p66-register.csv](adaq4224/tables/table-44-p66-register.csv), p. 66)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:2] | OSC_LIMIT | Oscillator Limit Setting. Oscillator is limited to this number of clock pulses plus one. Automatically calculated by the ADAQ4224 based on the data-word size, number of active SDO lanes, and data rate mode (SDR or DDR). | 0x0 | R |
| [1:0] | OSC_DIV | Oscillator Divider Setting. 00 = No divide (divide by 1). 01 = Divide by 2. | 0x0 | R/W |
|  |  | 10 = Divide by 4. |  |  |
|  |  | 11 = Invalid setting. |  |  |


### OUTPUT DRIVER REGISTER
<!-- page: 67 -->

**Address: 0x22, Reset: 0x00, Name: IO**

![register bitfield (p. 67)](adaq4224/figures/adaq4224-f149.png)

### Table 46. Bit Descriptions for IO
<!-- page: 67 -->

**Table 46. Bit Descriptions for IO** ([table-45-p67-register.csv](adaq4224/tables/table-45-p67-register.csv), p. 67)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | IO2X | Double Output Driver Strength. | 0x0 | R/W |
|  |  | 1 = Double output driver strength. |  |  |
|  |  | 0 = Normal output driver strength. |  |  |

### TEST PATTERN REGISTERS
<!-- page: 67 -->

**Address: 0x23, Reset: 0x0F, Name: TEST\_PAT\_BYTE0**

![register bitfield (p. 67)](adaq4224/figures/adaq4224-f150.png)

**Table 47. Bit Descriptions for TEST_PAT_BYTE0** ([table-46-p67-register.csv](adaq4224/tables/table-46-p67-register.csv), p. 67)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | TEST_DATA_PAT[7:0] | 32-Bit Test Pattern. Applied when OUT_DATA_MD = 4. | 0xF | R/W |

**Address: 0x24, Reset: 0x0F, Name: TEST\_PAT\_BYTE1**

![register bitfield (p. 67)](adaq4224/figures/adaq4224-f151.png)

**Table 48. Bit Descriptions for TEST_PAT_BYTE1** ([table-47-p67-register.csv](adaq4224/tables/table-47-p67-register.csv), p. 67)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | TEST_DATA_PAT[15:8] | 32-Bit Test Pattern. Applied when OUT_DATA_MD = 4. | 0xF | R/W |

**Address: 0x25, Reset: 0x5A, Name: TEST\_PAT\_BYTE2**

![register bitfield (p. 67)](adaq4224/figures/adaq4224-f152.png)

### Table 49. Bit Descriptions for TEST\_PAT\_BYTE2
<!-- page: 67 -->

**Table 49. Bit Descriptions for TEST_PAT_BYTE2** ([table-48-p67-register.csv](adaq4224/tables/table-48-p67-register.csv), p. 67)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | TEST_DATA_PAT[23:16] | 32-Bit Test Pattern. Applied when OUT_DATA_MD = 4. | 0x5A | R/W |

**Address: 0x26, Reset: 0x5A, Name: TEST\_PAT\_BYTE3**

![register bitfield (p. 68)](adaq4224/figures/adaq4224-f153.png)

**Table 50. Bit Descriptions for TEST_PAT_BYTE3** ([table-49-p68-register.csv](adaq4224/tables/table-49-p68-register.csv), p. 68)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | TEST_DATA_PAT[31:24] | 32-Bit Test Pattern. Applied when OUT_DATA_MD = 4. | 0x5A | R/W |

### DIGITAL DIAGNOSTICS REGISTER
<!-- page: 68 -->

**Address: 0x34, Reset: 0x40, Name: DIG\_DIAG**

![register bitfield (p. 68)](adaq4224/figures/adaq4224-f154.png)

**Table 51. Bit Descriptions for DIG_DIAG** ([table-50-p68-register.csv](adaq4224/tables/table-50-p68-register.csv), p. 68)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | POWERUP_COMPLETED | 1 = Power-Up Completed. Self clearing. | 0x0 | R |
| 6 | RESET_OCCURRED | Reset Occurred. This bit is set to 1 upon a reset event. Write 1 to clear (useful for detecting brownouts). | 0x1 | R/W1C |
| [5:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | FUSE_CRC_EN | Fuse CRC Enable. Write a 1 to force recheck of CRC. | 0x0 | R/W |

### DIGITAL ERRORS REGISTER
<!-- page: 68 -->

**Address: 0x35, Reset: 0x00, Name: DIG\_ERR**

![register bitfield (p. 68)](adaq4224/figures/adaq4224-f155.png)

**Table 52. Bit Descriptions for DIG_ERR** ([table-51-p68-register.csv](adaq4224/tables/table-51-p68-register.csv), p. 68)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | FUSE_CRC_ERR | Fuse CRC Error. This bit is set to 1 upon a fuse CRC error. Write 1 to clear. | 0x0 | R/W1C |

### TEMPERATURE SENSOR REGISTERS
<!-- pages: 69-70 -->

The ADAQ4224 has programmable user registers that are used to control and configure the temperature sensor. The registers are organized, as shown in Table 53. All memory commands are described in detail in the Function Commands column.

### Table 53. Temperature Sensor Register Summary
<!-- page: 69 -->

**Table 53. Temperature Sensor Register Summary** ([table-52-p69-register.csv](adaq4224/tables/table-52-p69-register.csv), p. 69)

| Offset | Read or Write | Register Name | Function Commands |
|---|---|---|---|
| 0x00 | R | T_{MSB}, T_{LSB} | Temperature 16-bit word. |
| 0x02 | R/W | CONFIGURATION/STATUS | Configuration/Status. |
| 0x04 | R/W | TH_MSB, TH_LSB | Alarm threshold high 16-bit word. |
| 0x06 | R/W | TL_MSB, TL_LSB | Alarm threshold low 16-bit word. |
| 0x08 | R/W | TH_HYST_MSB, TH_HYST_LSB | Hysteresis high threshold 16-bit word. |
| 0x0A | R/W | TL_HYST_MSB, TL_HYST_LSB | Hysteresis low threshold 16-bit word. |

### TEMPERATURE SENSOR REGISTER DETAILS
<!-- pages: 70-71 -->

### CONFIGURATION AND STATUS REGISTER
<!-- page: 70 -->

**Address 0x02, Name: CONFIGURATION/STATUS**

**Table 54. Bit Descriptions for CONFIGURATION/STATUS Register** ([table-53-p70-register.csv](adaq4224/tables/table-53-p70-register.csv), p. 70)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 15 | OVER TEMP STATUS | Indicates that the measured temperature is above the high threshold temperature. Behavior is set by the COMPARATOR/INTERRUPT and FAULT QUEUE bits. | 0b0 | R |
| 14 | UNDER TEMP STATUS | Indicates that the measured temperature is under the low threshold temperature. Behavior is set by the COMPARATOR/INTERRUPT and FAULT QUEUE bits. | 0b0 | R |
| 13 | PEC ERROR | 1 = When PEC enable bit is 1. 0 = When PEC enable bit is 0. | 0b0 | R |
| 12 | RESERVED | Reserved. | 0b0 | R |
| [11:10] | FAULT QUEUE | Sets how many consecutive temperature faults must occur before over temperature or under temperature faults are indicated in the status bits. | 0b00 | R/W |
| 9 | COMP/INT | 1 = OT and UT status bits in interrupt mode. 0 = OT and UT status bits in comparator mode. | 0b0 | R/W |
| 8 | ALARM POLARITY | 1 = ALARM pin active state is low. 0 = ALARM pin active state is high. | 0b0 | R/W |
| [7:6] | RESOLUTION | Sets the temperature conversion resolution. | 0b11 | R/W |
| 5 | TIMEOUT | 1 = Disables bus timeout. 0 = Enable bus timeout. | 0b0 | R/W |
| 4 | PEC ENABLE | 1 = A PEC byte is appended to the end of each message transfer. | 0b0 | R/W |
| [3:1] | CONVERSION RATE | 0b000 = Shutdown mode, else automatic conversion mode. If conversion is on going when this field is set to 0b000, the device completes the conversion first before entering shutdown mode. | 0b101 | R/W |
| 0 | ONE-SHOT | Set CONVERSION RATE bits first before setting this bit to 1. 1 = Prompts a new temperature conversion. Shutdown mode : Returns to 0 after temperature conversion. Automatic sampling mode: Complete ongoing conversion before starting a new sequence. | 0b0 | R/W |

### OUTLINE DIMENSIONS
<!-- page: 71 -->

14.10

![Figure 126. 178-Ball Chip-Scale Package, Ball Grid Array (CSP_BGA) (BC-178-2) Dimensions Shown in millimeters](adaq4224/figures/adaq4224-f156.png)

*Figure 126. 178-Ball Chip-Scale Package, Ball Grid Array [CSP_BGA] (BC-178-2) Dimensions Shown in millimeters*

### ORDERING GUIDE
<!-- page: 71 -->

**Ordering Guide** ([table-54-p71-data.csv](adaq4224/tables/table-54-p71-data.csv), p. 71)

| Model[^1] | Temperature Range | Package Description | Packing Quantity | Package Option |
|---|---|---|---|---|
| ADAQ4224BBCZ | −40°C to +105°C | 178-Lead, BGA (14 mm × 9 mm × 0.8 mm) | Tray, 182 | BC-178-2 |

- **Note 1:** Z = RoHS-Compliant Part.

### EVALUATION BOARDS
<!-- page: 71 -->

**Evaluation Boards** ([table-55-p71-data.csv](adaq4224/tables/table-55-p71-data.csv), p. 71)

| Evaluation Board[^1] | Description |
|---|---|
| EVAL-ADAQ4224-FMCZ | Evaluation Board |

- **Note 1:** Z = RoHS-Compliant Part.