---
type: Analog Component
title: "ADA4945-1 — High Speed, ±0.1 µV/˚C Offset Drift, Fully Differential ADC Driver"
description: "High Speed, ±0.1 µV/˚C Offset Drift, Fully Differential ADC Driver"
resource: "https://www.analog.com/en/products/ada4945-1.html"
tags: ["datasheet", "adi"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ada4945-1.pdf"
    title: "ADA4945-1 data sheet"
    author: "team:analog-devices"
tables:
  - file: "ada4945-1/tables/table-00-p4-data.csv"
    title: "Revision History"
    page: 4
  - file: "ada4945-1/tables/table-01-p5-spec.csv"
    title: "Table 1. Positive Input (+DIN) or Negative Input (–DIN) to Differential Output Voltage (VOUT, dm) Performance"
    page: 5
  - file: "ada4945-1/tables/table-02-p8-spec.csv"
    title: "Table 2. VOCM to Common-Mode Output Voltage (VOUT, cm) Performance"
    page: 8
  - file: "ada4945-1/tables/table-03-p9-spec.csv"
    title: "Table 3. General Performance"
    page: 9
  - file: "ada4945-1/tables/table-04-p10-spec.csv"
    title: "Table 4. +DIN or –DIN to VOUT, dm Performance"
    page: 10
  - file: "ada4945-1/tables/table-07-p15-spec.csv"
    title: "Table 7. +DIN or –DIN to VOUT, DM Performance"
    page: 15
  - file: "ada4945-1/tables/table-10-p21-abs_max.csv"
    title: "Table 10. Absolute Maximum Ratings"
    page: 21
  - file: "ada4945-1/tables/table-11-p21-data.csv"
    title: "Table 11. Thermal Resistance"
    page: 21
  - file: "ada4945-1/tables/table-12-p23-pin.csv"
    title: "Table 12.Pin Descriptions"
    page: 23
  - file: "ada4945-1/tables/table-13-p47-data.csv"
    title: "Table 13.Output Noise Voltage Density Calculations"
    page: 47
  - file: "ada4945-1/tables/table-14-p54-data.csv"
    title: "Table 14.SNR and THD for ADA4945-1 Driving AD7768 and AD4003"
    page: 54
  - file: "ada4945-1/tables/table-15-p55-data.csv"
    title: "Table 15. Recommended Converters"
    page: 55
  - file: "ada4945-1/tables/table-16-p56-data.csv"
    title: "Table 16. Ordering Guide"
    page: 56
  - file: "ada4945-1/tables/table-05-p13-spec.csv"
    title: "Table 5. VOCM to VOUT, CM Performance"
    page: 13
  - file: "ada4945-1/tables/table-06-p14-spec.csv"
    title: "Table 6. General Performance"
    page: 14
  - file: "ada4945-1/tables/table-08-p18-spec.csv"
    title: "Table 8. VOCM to VOUT, CM Performance"
    page: 18
  - file: "ada4945-1/tables/table-09-p19-spec.csv"
    title: "Table 9. General Performance"
    page: 19
figures:
  - file: "ada4945-1/figures/ada4945-1-f123.png"
    caption: "Figure 94. Equivalent Basic Test Circuit"
    type: "test_circuit"
    page: 40
  - file: "ada4945-1/figures/ada4945-1-f117-01.png"
    caption: "Figure 95. Test Circuit for Distortion Measurements"
    type: "test_circuit"
    page: 40
  - file: "ada4945-1/figures/ada4945-1-f117-02.png"
    caption: "Figure 96. Test Circuit for DISABLE Pin Turn Off Time Measurement"
    type: "test_circuit"
    page: 40
  - file: "ada4945-1/figures/ada4945-1-eqx02.png"
    caption: "Equation as printed (p. 42)"
    type: equation
    page: 42
  - file: "ada4945-1/figures/ada4945-1-f001.png"
    caption: "Figure 1. Functional Block Diagram"
    type: "block_diagram"
    page: 2
  - file: "ada4945-1/figures/ada4945-1-f004.png"
    caption: "Figure 2. Maximum Safe Power Dissipation vs. Ambient Temperature"
    type: "thermal"
    page: 22
  - file: "ada4945-1/figures/ada4945-1-f005.png"
    caption: "Figure 3. Pin Configuration"
    type: "pinout"
    page: 23
  - file: "ada4945-1/figures/ada4945-1-f006.png"
    caption: "Figure 4. Small Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 24
  - file: "ada4945-1/figures/ada4945-1-f007.png"
    caption: "Figure 5. Small Signal Frequency Response for Various Supplies"
    type: "characteristic_curve"
    page: 24
  - file: "ada4945-1/figures/ada4945-1-f008.png"
    caption: "Figure 6. Small Signal Frequency Response for Various Temperatures"
    type: "characteristic_curve"
    page: 24
  - file: "ada4945-1/figures/ada4945-1-f009.png"
    caption: "Figure 7. Large Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 24
  - file: "ada4945-1/figures/ada4945-1-f010.png"
    caption: "Figure 8. Large Signal Frequency Response for Various Supplies"
    type: "characteristic_curve"
    page: 24
  - file: "ada4945-1/figures/ada4945-1-f011.png"
    caption: "Figure 9.Large Signal Frequency Response for Various Temperatures"
    type: "characteristic_curve"
    page: 24
  - file: "ada4945-1/figures/ada4945-1-f012.png"
    caption: "Figure 10. Small Signal Frequency Response at Various VOCM Levels"
    type: "characteristic_curve"
    page: 25
  - file: "ada4945-1/figures/ada4945-1-f013.png"
    caption: "Figure 11. Large Signal Frequency Response at Various VOCM Levels"
    type: "characteristic_curve"
    page: 25
  - file: "ada4945-1/figures/ada4945-1-f014.png"
    caption: "Figure 12. Small Signal Frequency Response for Various Capacitive Loads"
    type: "characteristic_curve"
    page: 25
  - file: "ada4945-1/figures/ada4945-1-f015.png"
    caption: "Figure 13. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 25
  - file: "ada4945-1/figures/ada4945-1-f016.png"
    caption: "Figure 14. VOCM Small Signal Frequency Response"
    type: "characteristic_curve"
    page: 25
  - file: "ada4945-1/figures/ada4945-1-f017.png"
    caption: "Figure 15. Large Signal Frequency Response for Various Capacitive Loads"
    type: "characteristic_curve"
    page: 25
  - file: "ada4945-1/figures/ada4945-1-f018.png"
    caption: "Figure 16. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 26
  - file: "ada4945-1/figures/ada4945-1-f019.png"
    caption: "Figure 17. VOCM Large Signal Frequency Response"
    type: "characteristic_curve"
    page: 26
  - file: "ada4945-1/figures/ada4945-1-f020.png"
    caption: "Figure 18. Input Offset Voltage vs. Temperature for 50 Devices"
    type: "characteristic_curve"
    page: 26
  - file: "ada4945-1/figures/ada4945-1-f021.png"
    caption: "Figure 19. Input Offset Current vs. Temperature for 30 Devices"
    type: "characteristic_curve"
    page: 26
  - file: "ada4945-1/figures/ada4945-1-f022.png"
    caption: "Figure 20. Harmonic Distortion vs. Frequency for Various Loads"
    type: "characteristic_curve"
    page: 26
  - file: "ada4945-1/figures/ada4945-1-f023.png"
    caption: "Figure 21. Harmonic Distortion vs. Frequency for Various Supplies"
    type: "characteristic_curve"
    page: 26
  - file: "ada4945-1/figures/ada4945-1-f024.png"
    caption: "Figure 22. Harmonic Distortion vs. Frequency for Various Gains"
    type: "characteristic_curve"
    page: 27
  - file: "ada4945-1/figures/ada4945-1-f025.png"
    caption: "Figure 23. Harmonic Distortion vs. VOCM, f = 1 kHz, ±5 V Supplies"
    type: "characteristic_curve"
    page: 27
  - file: "ada4945-1/figures/ada4945-1-f026.png"
    caption: "Figure 24. Harmonic Distortion vs. VOCM, f = 1 kHz, ±2.5 V Supplies"
    type: "characteristic_curve"
    page: 27
  - file: "ada4945-1/figures/ada4945-1-f027.png"
    caption: "Figure 25. Harmonic Distortion vs. Frequency for Various VOUT, dm"
    type: "characteristic_curve"
    page: 27
  - file: "ada4945-1/figures/ada4945-1-f028.png"
    caption: "Figure 26. Harmonic Distortion vs. VOUT, dm for Various Supplies, f = 1 kHz"
    type: "characteristic_curve"
    page: 27
  - file: "ada4945-1/figures/ada4945-1-f029.png"
    caption: "Figure27. Harmonic Distortion vs. Frequency for Various RF and RG Values"
    type: "characteristic_curve"
    page: 27
  - file: "ada4945-1/figures/ada4945-1-f031.png"
    caption: "Figure 34. Input Current Noise Spectral Density"
    type: "characteristic_curve"
    page: 29
  - file: "ada4945-1/figures/ada4945-1-f032.png"
    caption: "Figure 35. DISABLE Pin Turn-Off Time"
    type: "characteristic_curve"
    page: 29
  - file: "ada4945-1/figures/ada4945-1-f033.png"
    caption: "Figure 36. 0.1% Settling Time"
    type: "characteristic_curve"
    page: 29
  - file: "ada4945-1/figures/ada4945-1-f034.png"
    caption: "Figure 37. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1"
    type: "characteristic_curve"
    page: 29
  - file: "ada4945-1/figures/ada4945-1-f035.png"
    caption: "Figure 38. DISABLE Pin Turn-On Time"
    type: "characteristic_curve"
    page: 29
  - file: "ada4945-1/figures/ada4945-1-f036.png"
    caption: "Figure 39. Small Signal Transient Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 29
  - file: "ada4945-1/figures/ada4945-1-f037.png"
    caption: "Figure 40. Small Signal Transient Response for Various Capacitive Loads, VS =10V"
    type: "characteristic_curve"
    page: 30
  - file: "ada4945-1/figures/ada4945-1-f038.png"
    caption: "Figure 41. Small Signal Transient Response for Various Capacitive Loads, VS=5V"
    type: "characteristic_curve"
    page: 30
  - file: "ada4945-1/figures/ada4945-1-f039.png"
    caption: "Figure 42. Small Signal Transient Response for Various Capacitive Loads, VS = 3V"
    type: "characteristic_curve"
    page: 30
  - file: "ada4945-1/figures/ada4945-1-f040.png"
    caption: "Figure 43. Large Signal Transient Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 30
  - file: "ada4945-1/figures/ada4945-1-f041.png"
    caption: "Figure 44. Large Signal Transient Response for Various Capacitive Loads, VS = 10 V"
    type: "characteristic_curve"
    page: 30
  - file: "ada4945-1/figures/ada4945-1-f042.png"
    caption: "Figure 45. Large Signal Transient Response for Various Capacitive Loads, VS= 5V"
    type: "characteristic_curve"
    page: 30
  - file: "ada4945-1/figures/ada4945-1-f043.png"
    caption: "Figure 46. Large Signal Transient Response for Various Capacitive Loads, VS=3V"
    type: "characteristic_curve"
    page: 31
  - file: "ada4945-1/figures/ada4945-1-f044.png"
    caption: "Figure 47. VOCM Small Signal Transient Response"
    type: "characteristic_curve"
    page: 31
  - file: "ada4945-1/figures/ada4945-1-f045.png"
    caption: "Figure 48. VOCM Large Signal Transient Response"
    type: "characteristic_curve"
    page: 31
  - file: "ada4945-1/figures/ada4945-1-f046.png"
    caption: "Figure 49. Small Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 32
  - file: "ada4945-1/figures/ada4945-1-f047.png"
    caption: "Figure 50. Small Signal Frequency Response for Various Supplies"
    type: "characteristic_curve"
    page: 32
  - file: "ada4945-1/figures/ada4945-1-f048.png"
    caption: "Figure 51. Small Signal Frequency Response for Various Temperatures"
    type: "characteristic_curve"
    page: 32
  - file: "ada4945-1/figures/ada4945-1-f049.png"
    caption: "Figure 52. Large Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 32
  - file: "ada4945-1/figures/ada4945-1-f050.png"
    caption: "Figure 53. Large Signal Frequency Response for Various Supplies"
    type: "characteristic_curve"
    page: 32
  - file: "ada4945-1/figures/ada4945-1-f051.png"
    caption: "Figure 54. Large Signal Frequency Response for Various Temperatures"
    type: "characteristic_curve"
    page: 32
  - file: "ada4945-1/figures/ada4945-1-f052.png"
    caption: "Figure 55. Small Signal Frequency Response at Various VOCM Levels"
    type: "characteristic_curve"
    page: 33
  - file: "ada4945-1/figures/ada4945-1-f053.png"
    caption: "Figure 56. Large Signal Frequency Response at Various VOCM Levels"
    type: "characteristic_curve"
    page: 33
  - file: "ada4945-1/figures/ada4945-1-f054.png"
    caption: "Figure 57. Small Signal Frequency Response for Various Capacitive Loads"
    type: "characteristic_curve"
    page: 33
  - file: "ada4945-1/figures/ada4945-1-f055.png"
    caption: "Figure 58. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 33
  - file: "ada4945-1/figures/ada4945-1-f056.png"
    caption: "Figure 59. VOCM Small Signal Frequency"
    type: "characteristic_curve"
    page: 33
  - file: "ada4945-1/figures/ada4945-1-f057.png"
    caption: "Figure 60. Large Signal Frequency Response for Various Capacitive Loads"
    type: "characteristic_curve"
    page: 33
  - file: "ada4945-1/figures/ada4945-1-f058.png"
    caption: "Figure 61. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 34
  - file: "ada4945-1/figures/ada4945-1-f059.png"
    caption: "Figure 62. VOCM Large Signal Frequency"
    type: "characteristic_curve"
    page: 34
  - file: "ada4945-1/figures/ada4945-1-f060.png"
    caption: "Figure 63. Input Offset Voltage vs. Temperature for 50 Devices"
    type: "characteristic_curve"
    page: 34
  - file: "ada4945-1/figures/ada4945-1-f061.png"
    caption: "Figure 64. Input Offset Current vs. Temperature for 30 Devices"
    type: "characteristic_curve"
    page: 34
  - file: "ada4945-1/figures/ada4945-1-f062.png"
    caption: "Figure 65. Harmonic Distortion vs. Frequency for Various Loads"
    type: "characteristic_curve"
    page: 34
  - file: "ada4945-1/figures/ada4945-1-f063.png"
    caption: "Figure 66. Harmonic Distortion vs. Frequency for Various Supplies"
    type: "characteristic_curve"
    page: 34
  - file: "ada4945-1/figures/ada4945-1-f064.png"
    caption: "Figure 67. Harmonic Distortion vs. Frequency for Various Gains"
    type: "characteristic_curve"
    page: 35
  - file: "ada4945-1/figures/ada4945-1-f065.png"
    caption: "Figure 68. Harmonic Distortion vs. VOCM, f = 1 kHz, ±5 V Supplies"
    type: "characteristic_curve"
    page: 35
  - file: "ada4945-1/figures/ada4945-1-f066.png"
    caption: "Figure 69. Harmonic Distortion vs. VOCM, f = 1 kHz, ±2.5 V Supplies"
    type: "characteristic_curve"
    page: 35
  - file: "ada4945-1/figures/ada4945-1-f067.png"
    caption: "Figure 70. Harmonic Distortion vs. Frequency for Various VOUT, dm"
    type: "characteristic_curve"
    page: 35
  - file: "ada4945-1/figures/ada4945-1-f068.png"
    caption: "Figure 71. Harmonic Distortion vs. VOUT, dm for Various Supplies, f = 1 kHz"
    type: "characteristic_curve"
    page: 35
  - file: "ada4945-1/figures/ada4945-1-f069.png"
    caption: "Figure 72. Harmonic Distortion vs. Frequency for Various RF and RG Values"
    type: "characteristic_curve"
    page: 35
  - file: "ada4945-1/figures/ada4945-1-f071.png"
    caption: "Figure 79. Current Noise Spectral Density"
    type: "characteristic_curve"
    page: 37
  - file: "ada4945-1/figures/ada4945-1-f072.png"
    caption: "Figure 80. DISABLE Pin Turn-Off Time"
    type: "characteristic_curve"
    page: 37
  - file: "ada4945-1/figures/ada4945-1-f073.png"
    caption: "Figure 81. 0.1% Settling Time"
    type: "characteristic_curve"
    page: 37
  - file: "ada4945-1/figures/ada4945-1-f074.png"
    caption: "Figure 82. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1"
    type: "characteristic_curve"
    page: 37
  - file: "ada4945-1/figures/ada4945-1-f075.png"
    caption: "Figure 83. DISABLE Pin Turn-On Time"
    type: "characteristic_curve"
    page: 37
  - file: "ada4945-1/figures/ada4945-1-f076.png"
    caption: "Figure 84. Small Signal Transient Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 37
  - file: "ada4945-1/figures/ada4945-1-f077.png"
    caption: "Figure 85. Small Signal Transient Response for Various Capacitive Loads, VS= 10V"
    type: "characteristic_curve"
    page: 38
  - file: "ada4945-1/figures/ada4945-1-f078.png"
    caption: "Figure 86. Small Signal Transient Response for Various Capacitive Loads, VS= 5V"
    type: "characteristic_curve"
    page: 38
  - file: "ada4945-1/figures/ada4945-1-f079.png"
    caption: "Figure 87. Small Signal Transient Response for Various Capacitive Loads, VS=3V"
    type: "characteristic_curve"
    page: 38
  - file: "ada4945-1/figures/ada4945-1-f080.png"
    caption: "Figure 88. Large Signal Transient Response for Various Gains and Loads"
    type: "characteristic_curve"
    page: 38
  - file: "ada4945-1/figures/ada4945-1-f081.png"
    caption: "Figure 89. Large Signal Transient Response for Various Capacitive Loads, VS= 10V"
    type: "characteristic_curve"
    page: 38
  - file: "ada4945-1/figures/ada4945-1-f082.png"
    caption: "Figure 90. Large Signal Transient Response for Various Capacitive Loads, VS= 5V"
    type: "characteristic_curve"
    page: 38
  - file: "ada4945-1/figures/ada4945-1-f083.png"
    caption: "Figure 91. Large Signal Transient Response for Various Capacitive Loads, VS=3V"
    type: "characteristic_curve"
    page: 39
  - file: "ada4945-1/figures/ada4945-1-f084.png"
    caption: "Figure 92. VOCM Small Signal Transient Response"
    type: "characteristic_curve"
    page: 39
  - file: "ada4945-1/figures/ada4945-1-f085.png"
    caption: "Figure 93. VOCM Large Signal Transient Response"
    type: "characteristic_curve"
    page: 39
  - file: "ada4945-1/figures/ada4945-1-f087.png"
    caption: "Figure 98. Circuit Definitions"
    type: "application_circuit"
    page: 42
  - file: "ada4945-1/figures/ada4945-1-f088.png"
    caption: "Figure 99. ADA4945-1 Architectural Block Diagram"
    type: "block_diagram"
    page: 43
  - file: "ada4945-1/figures/ada4945-1-f089.png"
    caption: "Figure 100. Common-Mode Clamp Block Diagram"
    type: "block_diagram"
    page: 44
  - file: "ada4945-1/figures/ada4945-1-f090.png"
    caption: "Figure 101. Differential Clamp Block Diagram"
    type: "block_diagram"
    page: 45
  - file: "ada4945-1/figures/ada4945-1-f091.png"
    caption: "Figure 102. ADA4945-1 Noise Model"
    type: "other"
    page: 46
  - file: "ada4945-1/figures/ada4945-1-f092.png"
    caption: "Figure 103. ADA4945-1 Configured for Balanced (Differential) Inputs"
    type: "application_circuit"
    page: 48
  - file: "ada4945-1/figures/ada4945-1-f093.png"
    caption: "Figure 104. ADA4945-1 with Unbalanced (Single-Ended) Input"
    type: "application_circuit"
    page: 48
  - file: "ada4945-1/figures/ada4945-1-f094.png"
    caption: "Figure 105. Single-Ended Input Impedance RIN"
    type: "application_circuit"
    page: 49
  - file: "ada4945-1/figures/ada4945-1-f095.png"
    caption: "Figure 106. Adding Termination Resistor, RT"
    type: "application_circuit"
    page: 49
  - file: "ada4945-1/figures/ada4945-1-f096.png"
    caption: "Figure 107. Thevenin Equivalent Circuit"
    type: "other"
    page: 49
  - file: "ada4945-1/figures/ada4945-1-f097.png"
    caption: "Figure 108. Thevenin Equivalent with Matched Gain Resistors"
    type: "application_circuit"
    page: 50
  - file: "ada4945-1/figures/ada4945-1-f098.png"
    caption: "Figure 109. Terminated Single-Ended-to-Differential System with G =1"
    type: "application_circuit"
    page: 50
  - file: "ada4945-1/figures/ada4945-1-f099.png"
    caption: "Figure 110. DISABLE Pin Circuit"
    type: "block_diagram"
    page: 51
  - file: "ada4945-1/figures/ada4945-1-f100.png"
    caption: "Figure 113. ADA4945-1 Output Voltage Clamp Usage"
    type: "application_circuit"
    page: 52
  - file: "ada4945-1/figures/ada4945-1-f103.png"
    caption: "Figure 116. ADA4945-1 Driving Precision ADC"
    type: "application_circuit"
    page: 54
  - file: "ada4945-1/figures/ada4945-1-f104.png"
    caption: "Figure 117. 16-Lead Lead Frame Chip Scale Package (LFCSP) 3 mm x 3mm Body and 0.75 mm Package Height (CP-16-22)"
    type: "other"
    page: 56
  - file: "ada4945-1/figures/ada4945-1-f105.png"
    caption: "Figure 28. CMRR vs. Frequency"
    type: "characteristic_curve"
    page: 28
  - file: "ada4945-1/figures/ada4945-1-f106.png"
    caption: "Figure 31. Open-Loop Gain and Phase vs. Frequency"
    type: "characteristic_curve"
    page: 28
  - file: "ada4945-1/figures/ada4945-1-f107.png"
    caption: "Figure 29. Output Balance vs. Frequency"
    type: "characteristic_curve"
    page: 28
  - file: "ada4945-1/figures/ada4945-1-f108.png"
    caption: "Figure 32. Output Overdrive Recovery, G = 2"
    type: "characteristic_curve"
    page: 28
  - file: "ada4945-1/figures/ada4945-1-f109.png"
    caption: "Figure 30. PSRR vs. Frequency"
    type: "characteristic_curve"
    page: 28
  - file: "ada4945-1/figures/ada4945-1-f110.png"
    caption: "Figure 33. Voltage Noise Spectral Density, Referred to Input"
    type: "characteristic_curve"
    page: 28
  - file: "ada4945-1/figures/ada4945-1-f111.png"
    caption: "Figure 73. CMRR vs. Frequency"
    type: "characteristic_curve"
    page: 36
  - file: "ada4945-1/figures/ada4945-1-f112.png"
    caption: "Figure 76. Open-Loop Gain and Phase vs. Frequency"
    type: "characteristic_curve"
    page: 36
  - file: "ada4945-1/figures/ada4945-1-f113.png"
    caption: "Figure 74. Output Balance vs. Frequency"
    type: "characteristic_curve"
    page: 36
  - file: "ada4945-1/figures/ada4945-1-f114.png"
    caption: "Figure 77. Output Overdrive Recovery, G = 2"
    type: "characteristic_curve"
    page: 36
  - file: "ada4945-1/figures/ada4945-1-f115.png"
    caption: "Figure 75. PSRR vs. Frequency"
    type: "characteristic_curve"
    page: 36
  - file: "ada4945-1/figures/ada4945-1-f116.png"
    caption: "Figure 78. Voltage Noise Spectral Density, Referred to Input"
    type: "characteristic_curve"
    page: 36
  - file: "ada4945-1/figures/ada4945-1-f118.png"
    caption: "Figure 97. Test Circuit for DISABLE Pin Turn On Time Measurement"
    type: "test_circuit"
    page: 40
  - file: "ada4945-1/figures/ada4945-1-f119.png"
    caption: "Figure 111. Series Resistance vs. Load Capacitance"
    type: "characteristic_curve"
    page: 52
  - file: "ada4945-1/figures/ada4945-1-f120.png"
    caption: "Figure 112. Series Resistance with a Capacitive Load Test Circuit"
    type: "test_circuit"
    page: 52
  - file: "ada4945-1/figures/ada4945-1-f121.png"
    caption: "Figure 114. Clamped Differential Signal Levels"
    type: "characteristic_curve"
    page: 53
  - file: "ada4945-1/figures/ada4945-1-f122.png"
    caption: "Figure 115. Clamped Common-Mode Signal Levels"
    type: "characteristic_curve"
    page: 53
  - file: "ada4945-1/figures/ada4945-1-eq01.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq02.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq03.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq04.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq05.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq06.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq07.png"
    caption: "Equation as printed (p. 41)"
    type: equation
    page: 41
  - file: "ada4945-1/figures/ada4945-1-eq08.png"
    caption: "Equation as printed (p. 43)"
    type: equation
    page: 43
  - file: "ada4945-1/figures/ada4945-1-eq09.png"
    caption: "Equation as printed (p. 43)"
    type: equation
    page: 43
  - file: "ada4945-1/figures/ada4945-1-eq10.png"
    caption: "Equation as printed (p. 43)"
    type: equation
    page: 43
  - file: "ada4945-1/figures/ada4945-1-eq11.png"
    caption: "Equation as printed (p. 44)"
    type: equation
    page: 44
  - file: "ada4945-1/figures/ada4945-1-eq12.png"
    caption: "Equation as printed (p. 44)"
    type: equation
    page: 44
  - file: "ada4945-1/figures/ada4945-1-eq13.png"
    caption: "Equation as printed (p. 44)"
    type: equation
    page: 44
  - file: "ada4945-1/figures/ada4945-1-eq14.png"
    caption: "Equation as printed (p. 44)"
    type: equation
    page: 44
  - file: "ada4945-1/figures/ada4945-1-eq16.png"
    caption: "Equation as printed (p. 46)"
    type: equation
    page: 46
  - file: "ada4945-1/figures/ada4945-1-eq17.png"
    caption: "Equation as printed (p. 46)"
    type: equation
    page: 46
  - file: "ada4945-1/figures/ada4945-1-eq18.png"
    caption: "Equation as printed (p. 46)"
    type: equation
    page: 46
  - file: "ada4945-1/figures/ada4945-1-eq19.png"
    caption: "Equation as printed (p. 46)"
    type: equation
    page: 46
  - file: "ada4945-1/figures/ada4945-1-eq20.png"
    caption: "Equation as printed (p. 47)"
    type: equation
    page: 47
  - file: "ada4945-1/figures/ada4945-1-eq21.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ada4945-1/figures/ada4945-1-eq22.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ada4945-1/figures/ada4945-1-eq23.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ada4945-1/figures/ada4945-1-eq24.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ada4945-1/figures/ada4945-1-eq25.png"
    caption: "Equation as printed (p. 48)"
    type: equation
    page: 48
  - file: "ada4945-1/figures/ada4945-1-eq26.png"
    caption: "Equation as printed (p. 49)"
    type: equation
    page: 49
curves:
  - file: "ada4945-1/curves/0-1-db-flatness-large-signal-frequency-response-for-various-gains-and-loads.csv"
    caption: "Figure 61. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads"
    figure: "ada4945-1/figures/ada4945-1-f058.png"
    page: 34
  - file: "ada4945-1/curves/0-1-db-flatness-small-signal-frequency-response-for-various-gains-and-loads.csv"
    caption: "Figure 58. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads"
    figure: "ada4945-1/figures/ada4945-1-f055.png"
    page: 33
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "V(OUT, dm) = 0.1V p-p"
  - file: "ada4945-1/curves/0-1-settling-time.csv"
    caption: "Figure 81. 0.1% Settling Time"
    figure: "ada4945-1/figures/ada4945-1-f073.png"
    page: 37
    x_unit: "ns"
    y_unit: "V"
    conditions: "VOUT, dm = 8V p-p"
  - file: "ada4945-1/curves/clamped-common-mode-signal-levels.csv"
    caption: "Figure 115. Clamped Common-Mode Signal Levels"
    figure: "ada4945-1/figures/ada4945-1-f122.png"
    page: 53
    x_unit: "µs"
    y_unit: "V"
    conditions: "+VS = +7V, -VS = -2V, +VCLAMP = +5V, -VCLAMP = 0V, +DIN = -DIN = 0V"
  - file: "ada4945-1/curves/clamped-differential-signal-levels.csv"
    caption: "Figure 114. Clamped Differential Signal Levels"
    figure: "ada4945-1/figures/ada4945-1-f121.png"
    page: 53
    x_unit: "µs"
    y_unit: "V"
    conditions: "+VS = +7V, −VS = −2V, +VCLAMP = +5V, −VCLAMP = 0V, VOCM = +2.5V"
  - file: "ada4945-1/curves/closed-loop-output-impedance-magnitude-vs-frequency-g-1.csv"
    caption: "Figure 82. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1"
    figure: "ada4945-1/figures/ada4945-1-f074.png"
    page: 37
    x_unit: "MHz"
    y_unit: "Ω"
  - file: "ada4945-1/curves/cmrr-vs-frequency.csv"
    caption: "Figure 73. CMRR vs. Frequency"
    figure: "ada4945-1/figures/ada4945-1-f111.png"
    page: 36
    x_unit: "MHz"
    y_unit: "dB"
  - file: "ada4945-1/curves/current-noise-spectral-density.csv"
    caption: "Figure 79. Current Noise Spectral Density"
    figure: "ada4945-1/figures/ada4945-1-f071.png"
    page: 37
    x_unit: "Hz"
    y_unit: "pA/√Hz"
    conditions: "10 AMPLIFIERS"
  - file: "ada4945-1/curves/disable-pin-turn-off-time.csv"
    caption: "Figure 80. DISABLE Pin Turn-Off Time"
    figure: "ada4945-1/figures/ada4945-1-f072.png"
    page: 37
    x_unit: "µs"
    y_unit: "mA"
  - file: "ada4945-1/curves/disable-pin-turn-on-time.csv"
    caption: "Figure 83. DISABLE Pin Turn-On Time"
    figure: "ada4945-1/figures/ada4945-1-f075.png"
    page: 37
    x_unit: "µs"
    y_unit: "V"
  - file: "ada4945-1/curves/figure27-harmonic-distortion-vs-frequency-for-various-rf-and-r-g-values.csv"
    caption: "Figure27. Harmonic Distortion vs. Frequency for Various RF and RG Values"
    figure: "ada4945-1/figures/ada4945-1-f029.png"
    page: 27
    x_unit: "Hz"
    y_unit: "dBc"
    conditions: "VOUT, dm = 8V p-p"
  - file: "ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-gains.csv"
    caption: "Figure 67. Harmonic Distortion vs. Frequency for Various Gains"
    figure: "ada4945-1/figures/ada4945-1-f064.png"
    page: 35
    x_unit: "Hz"
    y_unit: "dBc"
    conditions: "VOUT, dm = 8V p-p"
  - file: "ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-loads.csv"
    caption: "Figure 65. Harmonic Distortion vs. Frequency for Various Loads"
    figure: "ada4945-1/figures/ada4945-1-f062.png"
    page: 34
    x_unit: "Hz"
    y_unit: "dBc"
    conditions: "V(OUT, dm) = 8V p-p"
  - file: "ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-rf-and-r-g-values.csv"
    caption: "Figure 72. Harmonic Distortion vs. Frequency for Various RF and RG Values"
    figure: "ada4945-1/figures/ada4945-1-f069.png"
    page: 35
  - file: "ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-supplies.csv"
    caption: "Figure 66. Harmonic Distortion vs. Frequency for Various Supplies"
    figure: "ada4945-1/figures/ada4945-1-f063.png"
    page: 34
    x_unit: "Hz"
    y_unit: "dBc"
    conditions: "VOUT, dm = 8V p-p"
  - file: "ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-v-out-dm.csv"
    caption: "Figure 70. Harmonic Distortion vs. Frequency for Various VOUT, dm"
    figure: "ada4945-1/figures/ada4945-1-f067.png"
    page: 35
    x_unit: "Hz"
    y_unit: "dBc"
  - file: "ada4945-1/curves/harmonic-distortion-vs-v-ocm-f-1-khz-2-5-v-supplies.csv"
    caption: "Figure 69. Harmonic Distortion vs. VOCM, f = 1 kHz, ±2.5 V Supplies"
    figure: "ada4945-1/figures/ada4945-1-f066.png"
    page: 35
    x_unit: "V"
    y_unit: "dBc"
    conditions: "V_OUT, dm = 2V p-p"
  - file: "ada4945-1/curves/harmonic-distortion-vs-v-ocm-f-1-khz-5-v-supplies.csv"
    caption: "Figure 68. Harmonic Distortion vs. VOCM, f = 1 kHz, ±5 V Supplies"
    figure: "ada4945-1/figures/ada4945-1-f065.png"
    page: 35
    x_unit: "V"
    y_unit: "dBc"
    conditions: "VOUT, dm = 2V p-p"
  - file: "ada4945-1/curves/harmonic-distortion-vs-v-out-dm-for-various-supplies-f-1-khz.csv"
    caption: "Figure 71. Harmonic Distortion vs. VOUT, dm for Various Supplies, f = 1 kHz"
    figure: "ada4945-1/figures/ada4945-1-f068.png"
    page: 35
    x_unit: "V p-p"
    y_unit: "dBc"
    conditions: "f = 1kHz"
  - file: "ada4945-1/curves/input-current-noise-spectral-density.csv"
    caption: "Figure 34. Input Current Noise Spectral Density"
    figure: "ada4945-1/figures/ada4945-1-f031.png"
    page: 29
    x_unit: "Hz"
    y_unit: "pA/√Hz"
    conditions: "10 AMPLIFIERS"
  - file: "ada4945-1/curves/input-offset-current-vs-temperature-for-30-devices.csv"
    caption: "Figure 64. Input Offset Current vs. Temperature for 30 Devices"
    figure: "ada4945-1/figures/ada4945-1-f061.png"
    page: 34
    x_unit: "°C"
    y_unit: "nA"
    conditions: "NORMALIZED AT TA = 25°C"
  - file: "ada4945-1/curves/input-offset-voltage-vs-temperature-for-50-devices.csv"
    caption: "Figure 63. Input Offset Voltage vs. Temperature for 50 Devices"
    figure: "ada4945-1/figures/ada4945-1-f060.png"
    page: 34
    x_unit: "°C"
    y_unit: "µV"
    conditions: "NORMALIZED AT TA = 25°C"
  - file: "ada4945-1/curves/large-signal-frequency-response-at-various-vocm-levels.csv"
    caption: "Figure 56. Large Signal Frequency Response at Various VOCM Levels"
    figure: "ada4945-1/figures/ada4945-1-f053.png"
    page: 33
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOCM = 0V, ±1V; VOUT, dm = 2V p-p"
  - file: "ada4945-1/curves/large-signal-frequency-response-for-various-capacitive-loads.csv"
    caption: "Figure 60. Large Signal Frequency Response for Various Capacitive Loads"
    figure: "ada4945-1/figures/ada4945-1-f057.png"
    page: 33
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "CDIFF = 0pF, VOUT = 2V p-p"
  - file: "ada4945-1/curves/large-signal-frequency-response-for-various-gains-and-loads.csv"
    caption: "Figure 52. Large Signal Frequency Response for Various Gains and Loads"
    figure: "ada4945-1/figures/ada4945-1-f049.png"
    page: 32
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 2V p-p"
  - file: "ada4945-1/curves/large-signal-frequency-response-for-various-supplies.csv"
    caption: "Figure 53. Large Signal Frequency Response for Various Supplies"
    figure: "ada4945-1/figures/ada4945-1-f050.png"
    page: 32
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 2V p-p"
  - file: "ada4945-1/curves/large-signal-frequency-response-for-various-temperatures.csv"
    caption: "Figure 54. Large Signal Frequency Response for Various Temperatures"
    figure: "ada4945-1/figures/ada4945-1-f051.png"
    page: 32
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "V_OUT, dm = 2V p-p"
  - file: "ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-10-v.csv"
    caption: "Figure 44. Large Signal Transient Response for Various Capacitive Loads, VS = 10 V"
    figure: "ada4945-1/figures/ada4945-1-f041.png"
    page: 30
    x_unit: "ns"
    y_unit: "V"
    conditions: "CDIFF = 0pF, VOUT, dm = 8V p-p"
  - file: "ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-10v.csv"
    caption: "Figure 89. Large Signal Transient Response for Various Capacitive Loads, VS= 10V"
    figure: "ada4945-1/figures/ada4945-1-f081.png"
    page: 38
    x_unit: "µs"
    y_unit: "V"
    conditions: "C_DIFF = 0pF, V_OUT, dm = 8V p-p"
  - file: "ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-3v.csv"
    caption: "Figure 91. Large Signal Transient Response for Various Capacitive Loads, VS=3V"
    figure: "ada4945-1/figures/ada4945-1-f083.png"
    page: 39
    x_unit: "µs"
    y_unit: "V"
    conditions: "CDIFF = 0pF, VOUT, dm = 4V p-p"
  - file: "ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-5v.csv"
    caption: "Figure 90. Large Signal Transient Response for Various Capacitive Loads, VS= 5V"
    figure: "ada4945-1/figures/ada4945-1-f082.png"
    page: 38
    x_unit: "µs"
    y_unit: "V"
    conditions: "C_DIFF = 0pF, V_OUT, dm = 8V p-p"
  - file: "ada4945-1/curves/large-signal-transient-response-for-various-gains-and-loads.csv"
    caption: "Figure 88. Large Signal Transient Response for Various Gains and Loads"
    figure: "ada4945-1/figures/ada4945-1-f080.png"
    page: 38
    x_unit: "µs"
    y_unit: "V"
    conditions: "VOUT, dm = 8V p-p; G = 1, RL = 1kΩ; G = 1, RL = 100Ω; G = 2, RL = 1kΩ; G = 2, RL = 100Ω"
  - file: "ada4945-1/curves/maximum-safe-power-dissipation-vs-ambient-temperature.csv"
    caption: "Figure 2. Maximum Safe Power Dissipation vs. Ambient Temperature"
    figure: "ada4945-1/figures/ada4945-1-f004.png"
    page: 22
    x_unit: "°C"
    y_unit: "W"
  - file: "ada4945-1/curves/open-loop-gain-and-phase-vs-frequency.csv"
    caption: "Figure 76. Open-Loop Gain and Phase vs. Frequency"
    figure: "ada4945-1/figures/ada4945-1-f112.png"
    page: 36
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ada4945-1/curves/output-balance-vs-frequency.csv"
    caption: "Figure 74. Output Balance vs. Frequency"
    figure: "ada4945-1/figures/ada4945-1-f113.png"
    page: 36
    x_unit: "MHz"
    y_unit: "dB"
  - file: "ada4945-1/curves/output-overdrive-recovery-g-2.csv"
    caption: "Figure 77. Output Overdrive Recovery, G = 2"
    figure: "ada4945-1/figures/ada4945-1-f114.png"
    page: 36
    x_unit: "us"
    y_unit: "V"
    conditions: "G = +10"
  - file: "ada4945-1/curves/psrr-vs-frequency.csv"
    caption: "Figure 75. PSRR vs. Frequency"
    figure: "ada4945-1/figures/ada4945-1-f115.png"
    page: 36
    x_unit: "MHz"
    y_unit: "dB"
  - file: "ada4945-1/curves/series-resistance-vs-load-capacitance.csv"
    caption: "Figure 111. Series Resistance vs. Load Capacitance"
    figure: "ada4945-1/figures/ada4945-1-f119.png"
    page: 52
    x_unit: "pF"
    y_unit: "Ω"
  - file: "ada4945-1/curves/small-signal-frequency-response-at-various-vocm-levels.csv"
    caption: "Figure 55. Small Signal Frequency Response at Various VOCM Levels"
    figure: "ada4945-1/figures/ada4945-1-f052.png"
    page: 33
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-frequency-response-for-various-capacitive-loads.csv"
    caption: "Figure 57. Small Signal Frequency Response for Various Capacitive Loads"
    figure: "ada4945-1/figures/ada4945-1-f054.png"
    page: 33
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "CDIFF = 0pF, VOUT = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-frequency-response-for-various-gains-and-loads.csv"
    caption: "Figure 49. Small Signal Frequency Response for Various Gains and Loads"
    figure: "ada4945-1/figures/ada4945-1-f046.png"
    page: 32
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-frequency-response-for-various-supplies.csv"
    caption: "Figure 50. Small Signal Frequency Response for Various Supplies"
    figure: "ada4945-1/figures/ada4945-1-f047.png"
    page: 32
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-frequency-response-for-various-temperatures.csv"
    caption: "Figure 51. Small Signal Frequency Response for Various Temperatures"
    figure: "ada4945-1/figures/ada4945-1-f048.png"
    page: 32
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-v-s-10v.csv"
    caption: "Figure 85. Small Signal Transient Response for Various Capacitive Loads, VS= 10V"
    figure: "ada4945-1/figures/ada4945-1-f077.png"
    page: 38
    x_unit: "ns"
    y_unit: "mV"
    conditions: "CDIFF = 0pF, VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-v-s-3v.csv"
    caption: "Figure 87. Small Signal Transient Response for Various Capacitive Loads, VS=3V"
    figure: "ada4945-1/figures/ada4945-1-f079.png"
    page: 38
    x_unit: "ns"
    y_unit: "mV"
    conditions: "CDIFF = 0pF, VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-v-s-5v.csv"
    caption: "Figure 86. Small Signal Transient Response for Various Capacitive Loads, VS= 5V"
    figure: "ada4945-1/figures/ada4945-1-f078.png"
    page: 38
    x_unit: "ns"
    y_unit: "mV"
    conditions: "CDIFF = 0pF, VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-vs-10v.csv"
    caption: "Figure 40. Small Signal Transient Response for Various Capacitive Loads, VS =10V"
    figure: "ada4945-1/figures/ada4945-1-f037.png"
    page: 30
    x_unit: "ns"
    y_unit: "mV"
    conditions: "CDIFF = 0pF, VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/small-signal-transient-response-for-various-gains-and-loads.csv"
    caption: "Figure 84. Small Signal Transient Response for Various Gains and Loads"
    figure: "ada4945-1/figures/ada4945-1-f076.png"
    page: 37
    x_unit: "ns"
    y_unit: "mV"
    conditions: "VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/v-ocm-large-signal-frequency.csv"
    caption: "Figure 62. VOCM Large Signal Frequency"
    figure: "ada4945-1/figures/ada4945-1-f059.png"
    page: 34
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 2V p-p"
  - file: "ada4945-1/curves/v-ocm-large-signal-transient-response.csv"
    caption: "Figure 93. VOCM Large Signal Transient Response"
    figure: "ada4945-1/figures/ada4945-1-f085.png"
    page: 39
    x_unit: "µs"
    y_unit: "V"
    conditions: "V_OUT, dm = 2V p-p"
  - file: "ada4945-1/curves/v-ocm-small-signal-frequency.csv"
    caption: "Figure 59. VOCM Small Signal Frequency"
    figure: "ada4945-1/figures/ada4945-1-f056.png"
    page: 33
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "V_OUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/v-ocm-small-signal-frequency-response.csv"
    caption: "Figure 14. VOCM Small Signal Frequency Response"
    figure: "ada4945-1/figures/ada4945-1-f016.png"
    page: 25
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "V_OUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/v-ocm-small-signal-transient-response.csv"
    caption: "Figure 92. VOCM Small Signal Transient Response"
    figure: "ada4945-1/figures/ada4945-1-f084.png"
    page: 39
    x_unit: "ns"
    y_unit: "mV"
    conditions: "VOUT, dm = 0.1V p-p"
  - file: "ada4945-1/curves/vocm-large-signal-frequency-response.csv"
    caption: "Figure 17. VOCM Large Signal Frequency Response"
    figure: "ada4945-1/figures/ada4945-1-f019.png"
    page: 26
    x_unit: "MHz"
    y_unit: "dB"
    conditions: "VOUT, dm = 2V p-p"
  - file: "ada4945-1/curves/voltage-noise-spectral-density-referred-to-input.csv"
    caption: "Figure 78. Voltage Noise Spectral Density, Referred to Input"
    figure: "ada4945-1/figures/ada4945-1-f116.png"
    page: 36
    x_unit: "Hz"
    y_unit: "nV/√Hz"
    conditions: "10 AMPLIFIERS"
agentforge:
  part_number: "ADA4945-1"
  datasheet_revision: "A"
  repairs: 1
  reading_order: "structure-tree"
---

# ADA4945-1 — High Speed, ±0.1 µV/˚C Offset Drift, Fully Differential ADC Driver

*Datasheet: [ADA4945-1 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ada4945-1.pdf)*

### FEATURES
<!-- page: 1 -->

- Broad power supply range: 3 V to 10 V
- Wide input common-mode voltage range: −$V_{S}$ to +$V_{S}$ − 1.3 V
- Rail-to-rail output
- Fully specified dual power mode operation
  - 4 mA full power mode (145 MHz)
  - 1.4 mA low power mode (80 MHz)
- Full power mode
  - Low harmonic distortion
    - −133 dBc HD2 and −140 dBc HD3 at 1 kHz
    - −133 dBc HD2 and −116 dBc HD3 at 100 kHz
- Fast settling time
  - 18-bit: 100 ns
  - 16-bit: 50 ns
- Input voltage noise: 2.0 nV/√Hz, f = 100 kHz
- ±115 µV maximum offset voltage from −40°C to +125°C
- Adjustable output clamps for ADC input protection

### APPLICATIONS
<!-- page: 1 -->

- Low power Σ-Δ, PulSAR®, and SAR ADC drivers
- Single-ended to differential converters
- Differential buffers
- Medical imaging
- Process control
- Portable electronics

### GENERAL DESCRIPTION
<!-- pages: 1-2 -->

The ADA4945-1 is a low-noise, low-distortion, fully differential amplifier with two selectable power modes. The device operates over a broad power supply range of 3 V to 10 V. The low DC offset, DC offset drift, and excellent dynamic performance of the ADA4945-1 make it well suited for a variety of data acquisition and signal processing applications. The device is an ideal choice for driving high-resolution, high-performance successive approximation register (SAR) and Σ-Δ analog-to-digital converters (ADCs) on 4 mA of quiescent current (full power mode). The device can also be selected to operate on 1.4 mA of quiescent current (low power mode) to scale the power consumption to the desired performance necessary for an ADC drive application. The adjustable common-mode voltage allows the ADA4945-1 to match the input common-mode voltage of multiple ADCs. The internal common-mode feedback loop provides exceptional output balance, as well as suppression of even order harmonic distortion products.

With the ADA4945-1, differential gain configurations are achieved with a simple external feedback network of four resistors determining the closed-loop gain of the amplifier. The ADA4945-1 is fabricated using Analog Devices, Inc., proprietary, silicon germanium (SiGe), complementary bipolar process, enabling the device to achieve low levels of distortion with an input voltage noise of only 2.0 nV/√Hz (full power mode).

The ADA4945-1 is available in a RoHS-compliant, 3 mm × 3 mm, 16-lead LFCSP package. It is specified to operate from −40°C to +125°C.

**Rev. A** · [Document Feedback](https://form.analog.com/Form_Pages/feedback/documentfeedback.aspx) · [Technical Support](https://www.analog.com/en/support/technical-support.html)

One Analog Way, Wilmington, MA 01887-2356, U.S.A. · Tel: 781.329.4700 · ©2024 Analog Devices, Inc. All rights reserved.

### FUNCTIONAL BLOCK DIAGRAM
<!-- page: 2 -->

![Figure 1. Functional Block Diagram](ada4945-1/figures/ada4945-1-f001.png)

*Figure 1. Functional Block Diagram*

### TABLE OF CONTENTS
<!-- pages: 3-4 -->

- Features ... 1
- Applications ... 1
- General Description ... 1
- FUNCTIONAL BLOCK DIAGRAM ... 2
- Revision History ... 4
- Specifications ... 5
- Absolute Maximum Ratings ... 21
  - Thermal Resistance ... 21
  - Maximum Power Dissipation ... 21
  - ESD Caution ... 22
- Pin Configurations and Function Descriptions ... 23
- Typical Performance Characteristics (FULL POWER MODE) ... 24
- Typical Performance Characteristics (LOW POWER MODE) ... 32
- Test Circuits ... 40
- TERMINOLOGY ... 41
  - Differential Voltage ... 41
  - Common-Mode Voltage (CMV) ... 41
  - Common-Mode Offset Voltage ... 41
  - Differential $V_{OS}$, Differential CMRR, and $V_{OCM}$ CMRR ... 41
  - Balance ... 42
- Theory of Operation ... 43
  - Fully Differential and Common-Mode Signal Paths ... 43
  - Output Voltage Clamp ... 44
  - Power Modes ... 45
- Applications Information ... 46
  - Analyzing an Application Circuit ... 46
  - Setting the Closed-Loop Gain ... 46
  - Estimating the Output Noise Voltage ... 46
  - Impact of Mismatches in the Feedback Networks ... 47
  - Calculating the Input Impedance of an Application Circuit ... 47
  - Terminating a Single-Ended Input ... 48
  - Input Common-Mode Voltage Range ... 50
  - Input and Output Capacitive AC Coupling ... 50
  - Setting the Output Common-Mode Voltage ... 50
  - Disable Pin ... 51
  - Driving a Capacitive Load ... 51
  - Output Clamps ... 52
  - Driving a High Precision ADC ... 53
- LAYOUT, GROUNDING, AND BYPASSING ... 55
- OUTLINE DIMENSIONS ... 56
- Ordering Guide ... 56

### REVISION HISTORY
<!-- page: 4 -->

**Revision History** ([table-00-p4-data.csv](ada4945-1/tables/table-00-p4-data.csv), p. 4)

| Nature of Change | Page Number |
|---|---|
| **4/2019, Rev 0** |  |
| Initial release | — |
| **5/2024, Rev A** |  |
| Updated Features, General Description sections | 1 |
| Updated Electrical Characteristics (Table 1, Table 4, Table 7) | 5, 6, 7, 11, 12, 15, 16, 17 |
| Updated Driving a High Precision ADC section | 53 |
| Updated Table 14 | 54 |
| Updated Figure 33, Figure 34, Figure 78, Figure 79 | 28, 29, 36, 37 |

### SPECIFICATIONS
<!-- pages: 5-20 -->

**Table 1. Positive Input (+$D_{IN}$) or Negative Input (–$D_{IN}$) to Differential Output Voltage ($V_{OUT, dm}$) Performance** ([table-01-p5-spec.csv](ada4945-1/tables/table-01-p5-spec.csv), p. 5)

(SUPPLY VOLTAGE ($V_{S}$) = 10 V Output common-mode voltage ($V_{OCM}$) = midsupply, Gain (G) = 1, feedback resistance ($R_{F}$) = gain resistance ($R_{G}$) = 499 Ω, differential load resistance ($R_{L, dm}$) = 1 kΩ, and $T_{A}$ = 25°C, unless otherwise noted. All specifications refer to single-ended input and differential outputs, unless otherwise noted. Refer to Figure 98 for circuit definitions.)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **DYNAMIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 1 |  | 145 |  |  | 80 |  | MHz |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 2 |  | 95 |  |  | 40 |  | MHz |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 5 |  | 40 |  |  | 17 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 1 |  | 60 |  |  | 18 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 2 |  | 54 |  |  | 40 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 5 |  | 52 |  |  | 16 |  | MHz |
| Bandwidth for 0.1 dB Flatness | $f_{0.1dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 1 |  | 28 |  |  | 27 |  | MHz |
| Bandwidth for 0.1 dB Flatness | $f_{0.1dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 2 |  | 20 |  |  | 7 |  | MHz |
| Slew Rate | SR | $V_{OUT, dm}$ = 8 V step |  | 600 |  |  | 100 |  | V/µs |
| Settling Time to 0.1% | $t_{ST}$ | $V_{OUT, dm}$ = 8 V step |  | 35 |  |  | 85 |  | ns |
| Settling Time | $t_{ST}$ | 16-bit |  | 50 |  |  | 150 |  | ns |
| Settling Time | $t_{ST}$ | 18-bit |  | 100 |  |  | 300 |  | ns |
| Input Overdrive Recovery |  | G = 1, differential input voltage ($V_{IN, dm}$) = 10 V p-p, triangular waveform |  | 500 |  |  | 300 |  | ns |
| Output Overdrive Recovery |  | G = 10, $V_{IN, dm}$ = 2.4 V p-p, triangular waveform |  | 200 |  |  | 120 |  | ns |
| **NOISE/HARMONICE PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| NOISE/HARMONIC PERFORMANCE |  | $V_{OUT, dm}$ = 8 V p-p |  |  |  |  |  |  |  |
| Second Harmonic Distortion | HD2 | Center frequency ($f_{C}$) = 1 kHz |  | -133 |  |  | -133 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 100 kHz |  | -133 |  |  | -133 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 100 kHz, G = 2 |  | -128 |  |  | -128 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 1 MHz |  | -95 |  |  | -68 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 1 kHz |  | -140 |  |  | -138 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 100 kHz |  | -116 |  |  | -116 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 100 kHz, G = 2 |  | -123 |  |  | -122 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 1 MHz |  | -88 |  |  | -62 |  | dBc |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | f = 10 Hz |  | 5 |  |  | 6 |  | nV/√Hz |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | f = 100 kHz |  | 2.0 |  |  | 3.5 |  | nV/√Hz |
| Input Voltage Noise Differential |  | 1/f corner frequency |  | 100 |  |  | 40 |  | Hz |
| Common Mode | $V_{N, CM}$ | f = 10 Hz |  | 350 |  |  | 284 |  | nV/√Hz |
| Common Mode | $V_{N, CM}$ | f = 100 kHz |  | 30 |  |  | 38 |  | nV/√Hz |
| Common Mode |  | 1/f corner frequency |  | 1000 |  |  | 1000 |  | Hz |
| Integrated Voltage Noise |  | 0.1 Hz to 10 Hz |  | 35 |  |  | 35 |  | nV rms |
| Input Current Noise | $I_{N}$ | f = 10 Hz |  | 17 |  |  | 7 |  | pA/√Hz |
| Input Current Noise | $I_{N}$ | f = 100 kHz |  | 1.0 |  |  | 0.6 |  | pA/√Hz |
| Input Current Noise |  | 1/f corner frequency |  | 2000 |  |  | 1000 |  | Hz |
| **INPUT CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Input Offset Voltage | $V_{OS}$ | 25°C |  | ±10 | ±50 |  | ±10 | ±50 | µV |
| Input Offset Voltage | $V_{OS}$ | $T_{A}$ = 20°C to 85°C |  | ±15 | ±80 |  | ±15 | ±80 | µV |
| Input Offset Voltage | $V_{OS}$ | $T_{A}$ = −40°C to +125°C |  | ±30 | ±115 |  | ±30 | ±115 | µV |
| Input Offset Voltage Drift | $V_{OS\_TC}$ | $T_{A}$ = 20°C to 85°C |  | ±0.1 | ±0.5 |  | ±0.1 | ±0.5 | µV/°C |
| Input Offset Voltage Drift | $V_{OS\_TC}$ | $T_{A}$ = −40°C to +125°C |  | ±0.2 | ±1.0 |  | ±0.2 | ±1.0 | µV/°C |
| Input Bias Current | $I_{B}$ | $T_{A}$ = 25°C |  | −1.2 | −2.5 |  | −0.5 | −0.8 | µA |
| Input Bias Current | $I_{B}$ | $T_{A}$ = 20°C to 85°C |  | -1.5 | −3.0 |  | -0.6 | −1.0 | µA |
| Input Bias Current | $I_{B}$ | $T_{A}$ = −40°C to +125°C |  | -1.8 | −3.4 |  | -0.7 | −1.2 | µA |
| Input Bias Current Drift | $I_{B\_TC}$ | $T_{A}$ = 20°C to 85°C |  | -10 | −50 |  | -10 | −50 | nA/°C |
| Input Bias Current Drift | $I_{B\_TC}$ | $T_{A}$ = −40°C to +125°C |  | -10 | −50 |  | -10 | −50 | nA/°C |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = 25°C |  | ±20 | ±200 |  | ±10 | ±130 | nA |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = 20°C to 85°C |  | ±25 | ±250 |  | ±20 | ±150 | nA |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = −40°C to +125°C |  | ±40 | ±300 |  | ±25 | ±200 | nA |
| Input Offset Current Drift | $I_{OS\_TC}$ | $T_{A}$ = 20°C to 85°C |  | ±0.1 | ±0.6 |  | ±0.06 | ±0.38 | nA/°C |
| Input Offset Current Drift | $I_{OS\_TC}$ | $T_{A}$ = −40°C to +125°C |  | ±0.12 | ±0.7 |  | ±0.07 | ±0.4 | nA/°C |
| Input Common-Mode Voltage Range | $V_{CM}$ |  | −$V_{S}$ |  | +$V_{S}$ − 1.3 | −$V_{S}$ |  | +$V_{S}$ − 1.3 | V |
| Input Resistance | $R_{IN, DIFF}$ | Differential |  | 50 |  |  | 50 |  | kΩ |
| Input Resistance | $R_{IN, CM}$ | Common mode |  | 50 |  |  | 50 |  | MΩ |
| Input Capacitance | $C_{IN}$ |  |  | 1 |  |  | 1 |  | pF |
| Common-Mode Rejection Ratio | CMRR | $V_{CM}$ = 0.5 V to 8.7 V |  | -110 |  |  | -110 |  | dB |
| Open-Loop Gain | $A_{OL}$ | Output voltage ($V_{OUT}$) = ±4 V |  | 120 |  |  | 115 |  | dB |
| **OUTPUT CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Output Voltage Swing | $V_{OUT}$ | Load resistance ($R_{L}$) = 100 Ω for each single-ended output | −$V_{S}$ + 0.55 |  | +$V_{S}$ − 0.55 | −$V_{S}$ + 0.55 |  | +$V_{S}$ − 0.55 | V |
| Output Voltage Swing | $V_{OUT}$ | $R_{L}$ = 1 kΩ | −$V_{S}$ +0.1 |  | +$V_{S}$ −0.1 | −$V_{S}$ +0.1 |  | +$V_{S}$ −0.1 | V |
| Short-Circuit Current | $I_{SC}$ |  |  | 170 |  |  | 140 |  | mA peak |
| Output Balance Error |  | f = 100 kHz, Δ$V_{OUT,cm}$/Δ$V_{OUT,dm}$ |  | 100 |  |  | 100 |  | dB |

**Table 2. $V_{OCM}$ to Common-Mode Output Voltage ($V_{OUT, cm}$) Performance** ([table-02-p8-spec.csv](ada4945-1/tables/table-02-p8-spec.csv), p. 8)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **$V_{OCM}$ DYNAMIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| −3 dB Small Signal Bandwidth | $f_{3dB,VOCM}$ | $V_{OUT, cm}$ = 20 mV p-p |  | 35 |  |  | 15 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, cm}$ = 2 V p-p |  | 3.8 |  |  | 1.3 |  | MHz |
| Slew Rate | $SR_{VOCM}$ | $V_{OUT, cm}$ = 2 V p-p |  | 26 |  |  | 9 |  | V/µs |
| Input Voltage Noise | $V_{N, VOCM}$ | f = 100 kHz |  | 35 |  |  | 45 |  | nV/√Hz |
| Gain |  | Δ$V_{OUT, cm}$/Δ$V_{OCM}$, Δ$V_{OCM}$ = ±1 V | 0.99 | 1 | 1.01 | 0.99 | 1 | 1.01 | V/V |
| **$V_{OCM}$ CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Input Common-Mode Voltage Range | $V_{OCM}$ |  | −$V_{S}$ + 0.4 |  | +$V_{S}$ − 1.4 | −$V_{S}$ + 0.4 |  | +$V_{S}$ − 1.4 | V |
| Input Resistance | $R_{IN, VOCM}$ |  |  | 125 |  |  | 125 |  | kΩ |
| Offset Voltage | $V_{OS, VOCM}$ | Common mode offset ($V_{OS, cm}$) = $V_{OUT, cm}$ − $V_{OCM}$, positive input ($V_{IP}$) = negative input ($V_{IN}$) = $V_{OCM}$ = 0 V, 25°C |  | ±5 | ±60 |  | ±5 | ±60 | mV |
| Offset Voltage | $V_{OS, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | ±10 |  |  | ±10 |  | mV |
| Offset Voltage | $V_{OS, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | ±20 |  |  | ±20 |  | mV |
| Input Offset Voltage Drift | $V_{OS\_TC, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | ±5 |  |  | ±5 |  | µV/°C |
| Input Offset Voltage Drift | $V_{OS\_TC, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | ±10 |  |  | ±10 |  | µV/°C |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = 25°C |  | -220 |  |  | -160 |  | nA |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | -300 |  |  | -205 |  | nA |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | -350 |  |  | -230 |  | nA |
| Input Bias Current Drift | $I_{B\_TC, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | -1.3 |  |  | -0.75 |  | nA/°C |
| Input Bias Current Drift | $I_{B\_TC, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | -1.5 |  |  | -1.0 |  | nA/°C |
| CMRR | $CMRR_{VOCM}$ | Δ$V_{OS, dm}$/Δ$V_{OCM}$, Δ$V_{OCM}$ = ±1 V |  | -130 |  |  | -130 |  | dB |

**Table 3. General Performance** ([table-03-p9-spec.csv](ada4945-1/tables/table-03-p9-spec.csv), p. 9)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **CLAMP** |  |  |  |  |  |  |  |  |  |
| Clamp Output Voltage |  | Differential | −$V_{S}$ −0.5 |  | +$V_{S}$ +0.5 | −$V_{S}$ −0.5 |  | +$V_{S}$ +0.5 | V |
| Clamp Output Voltage |  | Common mode | −$V_{S}$ |  | +$V_{S}$ | −$V_{S}$ |  | +$V_{S}$ | V |
| Recovery Time |  |  |  | 100 |  |  | 100 |  | ns |
| Input Resistance |  | Resistance between +$V_{CLAMP}$ and −$V_{CLAMP}$ |  | 480 |  |  | 480 |  | kΩ |
| **DISABLE (D̅I̅S̅A̅B̅L̅E̅ PIN) MODE** |  |  |  |  |  |  |  |  |  |
| Input Voltage |  | Disabled | −$V_{S}$ −0.3 |  | $D_{GND}$ + 1 | −$V_{S}$ −0.3 |  | $D_{GND}$ + 1 | V |
| Input Voltage |  | Enabled | $D_{GND}$ +1.4 |  | +$V_{S}$ +0.3 | $D_{GND}$ +1.4 |  | +$V_{S}$ +0.3 | V |
| Turn Off Time | $t_{OFF}$ | Quiescent current<10% of enabled quiescent current |  | 6 |  |  | 6 |  | µs |
| Turn On Time | $t_{ON}$ | Turn on time($t_{o}$) >90% of final $V_{OUT}$ |  | 1.2 |  |  | 2 |  | µs |
| D̅I̅S̅A̅B̅L̅E̅ Pin Bias Current Enabled |  | D̅I̅S̅A̅B̅L̅E̅ = 10 V |  | 50 |  |  | 50 |  | nA |
| D̅I̅S̅A̅B̅L̅E̅ Pin Bias Current Disabled |  | D̅I̅S̅A̅B̅L̅E̅ = 0 V |  | 50 |  |  | 50 |  | nA |
| **$D_{GND}$ PIN** |  |  |  |  |  |  |  |  |  |
| VOLTAGE RANGE | $IVR_{DGND}$ |  | −$V_{S}$ |  | +$V_{S}$ −2.5 | −$V_{S}$ |  | +$V_{S}$ −2.5 | V |
| **POWER SUPPLY** |  |  |  |  |  |  |  |  |  |
| Operating Range | ±$V_{S}$ |  | 3 |  | 10 | 3 |  | 10 | V |
| Quiescent Current Enabled | $I_{q}$ | Full power mode, MODE = +$V_{S}$ |  | 4 | 4.2 |  |  |  | mA |
| Quiescent Current Enabled | $I_{q}$ | Low power mode, MODE = −$V_{S}$ |  |  |  |  | 1.4 | 1.6 | mA |
| Quiescent Current Disabled |  | Full power mode, MODE = +$V_{S}$ |  | 60 | 70 |  |  |  | µA |
| Quiescent Current Disabled |  | Low power mode, MODE = −$V_{S}$ |  |  |  |  | 60 | 70 | µA |
| Positive Power Supply Rejection Ratio | +PSRR | Δ$V_{OS, dm}$/Δ$V_{S}$, Δ$V_{S}$ = 1 V p-p |  | -120 |  |  | -120 |  | dB |
| Negative Power Supply Rejection Ratio | -PSRR | Δ$V_{OS, dm}$/Δ$V_{S}$, Δ$V_{S}$ = 1 V p-p |  | -120 |  |  | -120 |  | dB |
| OPERATING TEMPERATURE RANGE |  |  | -40 |  | +125 | -40 |  | +125 | °C |

**Table 4. +$D_{IN}$ or –$D_{IN}$ to $V_{OUT, dm}$ Performance** ([table-04-p10-spec.csv](ada4945-1/tables/table-04-p10-spec.csv), p. 10)

($V_{S}$ = 5 V $V_{OCM}$ = midsupply, G = 1, $R_{F}$ = $R_{G}$ = 499 Ω, $R_{L, dm}$ = 1 kΩ, $T_{A}$ = 25°C, unless otherwise noted. All specifications refer to single-ended input and differential outputs, unless otherwise noted. Refer to Figure 98 for circuits definitions.)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **DYNAMIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 1 |  | 145 |  |  | 80 |  | MHz |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 2 |  | 95 |  |  | 40 |  | MHz |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 5 |  | 40 |  |  | 17 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 1 |  | 60 |  |  | 18 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 2 |  | 54 |  |  | 40 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 5 |  | 52 |  |  | 16 |  | MHz |
| Bandwidth for 0.1 dB Flatness | $f_{0.1dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 1 |  | 28 |  |  | 27 |  | MHz |
| Bandwidth for 0.1 dB Flatness | $f_{0.1dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 2 |  | 20 |  |  | 7 |  | MHz |
| Slew Rate | SR | $V_{OUT, dm}$ = 8 V step |  | 600 |  |  | 100 |  | V/µs |
| Settling Time to 0.1% | $t_{ST}$ | $V_{OUT, dm}$ = 8 V step |  | 35 |  |  | 85 |  | ns |
| Settling Time | $t_{ST}$ | 16-bit |  | 50 |  |  | 150 |  | ns |
| Settling Time | $t_{ST}$ | 18-bit |  | 100 |  |  | 300 |  | ns |
| Input Overdrive Recovery |  | G = 1, $V_{IN, dm}$ = 10 V p-p, triangular waveform |  | 300 |  |  | 500 |  | ns |
| Output Overdrive Recovery |  | G = 2, $V_{IN, dm}$ = 6 V p-p, triangular waveform |  | 145 |  |  | 80 |  | ns |
| **NOISE/HARMONIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| NOISE/HARMONIC PERFORMANCE |  | $V_{OUT, dm}$ = 8 V p-p |  |  |  |  |  |  |  |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 1 kHz |  | -133 |  |  | -133 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 100 kHz |  | -133 |  |  | -133 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 100 kHz, G = 2 |  | -128 |  |  | -128 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 1 MHz |  | -95 |  |  | -68 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 1 kHz |  | -140 |  |  | -138 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 100 kHz |  | -116 |  |  | -116 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 100 kHz, G = 2 |  | -123 |  |  | -122 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 1 MHz |  | -88 |  |  | -62 |  | dBc |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | f = 10 Hz |  | 5 |  |  | 6 |  | nV/√Hz |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | f = 100 kHz |  | 2.0 |  |  | 3.5 |  | nV/√Hz |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | 1/f corner frequency |  | 100 |  |  | 40 |  | Hz |
| Input Voltage Noise Common Mode | $V_{N, CM}$ | f = 10 Hz |  | 350 |  |  | 284 |  | nV/√Hz |
| Input Voltage Noise Common Mode | $V_{N, CM}$ | f = 100 kHz |  | 30 |  |  | 38 |  | nV/√Hz |
| Input Voltage Noise Common Mode | $V_{N, CM}$ | 1/f corner frequency |  | 1000 |  |  | 1000 |  | Hz |
| Integrated Voltage Noise |  | 0.1 Hz to 10 Hz |  | 35 |  |  | 35 |  | nV rms |
| Input Current Noise | $I_{N}$ | f = 10 Hz |  | 17 |  |  | 7 |  | pA/√Hz |
| Input Current Noise | $I_{N}$ | f= 100 kHz |  | 1.0 |  |  | 0.6 |  | pA/√Hz |
| Input Current Noise | $I_{N}$ | 1/f corner frequency |  | 2000 |  |  | 1000 |  | Hz |
| **INPUT CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Input Offset Voltage | $V_{OS}$ | 25°C |  | ±10 | ±50 |  | ±10 | ±50 | µV |
| Input Offset Voltage | $V_{OS}$ | $T_{A}$ = 20°C to 85°C |  | ±15 | ±80 |  | ±15 | ±80 | µV |
| Input Offset Voltage | $V_{OS}$ | $T_{A}$ = −40°C to +125°C |  | ±30 | ±115 |  | ±30 | ±115 | µV |
| Input Offset Voltage Drift | $V_{OS\_TC}$ | $T_{A}$ = 20°C to 85°C |  | ±0.1 | ±0.5 |  | ±0.1 | ±0.5 | µV/°C |
| Input Offset Voltage Drift | $V_{OS\_TC}$ | $T_{A}$ = −40°C to +125°C |  | ±0.2 | ±1.0 |  | ±0.2 | ±1.0 | µV/°C |
| Input Bias Current | $I_{B}$ | $T_{A}$ = 25°C |  | −1.2 | −2.5 |  | −0.5 | −0.8 | µA |
| Input Bias Current | $I_{B}$ | $T_{A}$ = 20°C to 85°C |  | −1.5 | −3.0 |  | −0.6 | −1.0 | µA |
| Input Bias Current | $I_{B}$ | $T_{A}$ = −40°C to +125°C |  | −1.8 | −3.4 |  | −0.7 | −1.2 | µA |
| Input Bias Current Drift | $I_{B\_TC}$ | $T_{A}$ = 20°C to 85°C |  | −10 | −50 |  | −10 | −50 | nA/°C |
| Input Bias Current Drift | $I_{B\_TC}$ | $T_{A}$ = −40°C to +125°C |  | −10 | −50 |  | −10 | −50 | nA/°C |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = 25°C |  | ±20 | ±200 |  | ±10 | ±130 | nA |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = 20°C to 85°C |  | ±25 | ±250 |  | ±20 | ±150 | nA |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = −40°C to +125°C |  | ±40 | ±300 |  | ±25 | ±200 | nA |
| Input Offset Current Drift | $I_{OS\_TC}$ | $T_{A}$ = 20°C to 85°C |  | ±0.1 | ±0.6 |  | ±0.06 | ±0.38 | nA/°C |
| Input Offset Current Drift | $I_{OS\_TC}$ | $T_{A}$ = −40°C to +125°C |  | ±0.12 | ±0.7 |  | ±0.07 | ±0.4 | nA/°C |
| $V_{CM}$ Range | $V_{CM}$ |  | −$V_{S}$ |  | +$V_{S}$ −1.3 | −$V_{S}$ |  | +$V_{S}$ −1.3 | V |
| Input Resistance | $R_{IN, DIFF}$ | Differential |  | 50 |  |  | 50 |  | kΩ |
| Input Resistance | $R_{IN, CM}$ | Common mode |  | 50 |  |  | 50 |  | MΩ |
| Input Capacitance | $C_{IN}$ |  |  | 1 |  |  | 1 |  | pF |
| CMRR |  | $V_{CM}$ = 0.5 V to 3.7 V |  | −110 |  |  | −110 |  | dB |
| Open-Loop Gain | $A_{OL}$ | $V_{OUT}$ = ±4 V |  | 120 |  |  | 115 |  | dB |
| **OUTPUT CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Output Voltage Swing | $V_{OUT}$ | $R_{L}$ = 100 Ω | −$V_{S}$ + 0.55 |  | +$V_{S}$ − 0.55 | −$V_{S}$ + 0.55 |  | +$V_{S}$ − 0.55 | V |
| Output Voltage Swing | $V_{OUT}$ | $R_{L}$ = 1 kΩ | −$V_{S}$ +0.1 |  | +$V_{S}$ −0.1 | −$V_{S}$ +0.1 |  | +$V_{S}$ −0.1 | V |
| Short-Circuit Current | $I_{SC}$ |  |  | 170 |  |  | 140 |  | mA peak |
| Output Balance Error |  | f = 100 kHz, Δ$V_{OUT,cm}$/Δ$V_{OUT,dm}$ |  | 100 |  |  | 100 |  | dB |

**Table 5. VOCM to VOUT, CM Performance** ([table-05-p13-spec.csv](ada4945-1/tables/table-05-p13-spec.csv), p. 13)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **$V_{OCM}$ DYNAMIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| −3 dB Small Signal Bandwidth | $f_{3dB, VOCM}$ | $V_{OUT, cm}$ = 20 mV p-p |  | 35 |  |  | 15 |  | MHz |
| −3 dB Small Signal Bandwidth |  | $V_{OUT, cm}$ = 2 V p-p |  | 3.8 |  |  | 1.3 |  | MHz |
| Slew Rate | $SR_{VOCM}$ | $V_{OUT, cm}$ = 2 V p-p |  | 26 |  |  | 9 |  | V/µs |
| Input Voltage Noise | $V_{N, VOCM}$ | f = 100 kHz |  | 35 |  |  | 45 |  | nV/√Hz |
| Gain |  | Δ$V_{OUT, cm}$/Δ$V_{OCM}$, Δ$V_{OCM}$ = ±1 V | 0.99 | 1 | 1.01 | 0.99 | 1 | 1.01 | V/V |
| **$V_{OCM}$ CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Input Common-Mode Voltage Range | $V_{OCM}$ |  | −$V_{S}$ +0.4 |  | +$V_{S}$ −1.4 | −$V_{S}$ +0.4 |  | +$V_{S}$ −1.4 | V |
| Input Resistance | $R_{IN, VOCM}$ |  |  | 125 |  |  | 125 |  | kΩ |
| Offset Voltage | $V_{OS, VOCM}$ | $V_{OS, cm}$ = $V_{OUT, cm}$ − $V_{OCM}$, $V_{IP}$ = $V_{IN}$ = $V_{OCM}$ = 0 V, 25°C |  | ±10 | ±60 |  | ±10 | ±60 | mV |
| Offset Voltage | $V_{OS, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | ±10 |  |  | ±10 |  | mV |
| Offset Voltage | $V_{OS, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | ±20 |  |  | ±20 |  | mV |
| Input Offset Voltage Drift | $V_{OS\_TC, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | ±5 |  |  | ±5 |  | µV/°C |
| Input Offset Voltage Drift | $V_{OS\_TC, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | ±10 |  |  | ±10 |  | µV/°C |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = 25°C |  | −220 |  |  | −160 |  | nA |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | −300 |  |  | −205 |  | nA |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | −350 |  |  | −230 |  | nA |
| Input Bias Current Drift | $I_{B\_TC, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | −1.3 |  |  | −0.75 |  | nA/°C |
| Input Bias Current Drift | $I_{B\_TC, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | −1.5 |  |  | −1.0 |  | nA/°C |
| CMRR | $CMRR_{VOCM}$ | Δ$V_{OS, dm}$/Δ$V_{OCM}$, Δ$V_{OCM}$ = ±1 V |  | −130 |  |  | −130 |  | dB |

**Table 6. General Performance** ([table-06-p14-spec.csv](ada4945-1/tables/table-06-p14-spec.csv), p. 14)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **CLAMP** |  |  |  |  |  |  |  |  |  |
| Clamp Output Voltage |  | Differential | −$V_{S}$ −0.5 |  | +$V_{S}$ +0.5 | −$V_{S}$ −0.5 |  | +$V_{S}$ +0.5 | V |
| Clamp Output Voltage |  | Common mode | −$V_{S}$ |  | +$V_{S}$ | −$V_{S}$ |  | +$V_{S}$ | V |
| Recovery Time |  |  |  | 100 |  |  | 100 |  | ns |
| Input Resistance |  | Resistance between +$V_{CLAMP}$ and −$V_{CLAMP}$ |  | 480 |  |  | 480 |  | kΩ |
| **DISABLE (D̅I̅S̅A̅B̅L̅E̅ PIN) MODE** |  |  |  |  |  |  |  |  |  |
| Input Voltage |  | Disabled | −$V_{S}$ −0.3 |  | $D_{GND}$ + 1 | −$V_{S}$ −0.3 |  | $D_{GND}$ + 1 | V |
| Input Voltage |  | Enabled | $D_{GND}$ +1.4 |  | +$V_{S}$ + 0.3 | $D_{GND}$ +1.4 |  | +$V_{S}$ + 0.3 | V |
| Turn Off Time | $t_{OFF}$ | Quiescent current<10% of enabled quiescent current |  | 6 |  |  | 6 |  | µs |
| Turn On Time | $t_{ON}$ | $t_{O}$ >90% of final $V_{OUT}$ |  | 1.2 |  |  | 2 |  | µs |
| D̅I̅S̅A̅B̅L̅E̅ Pin Bias Current Enabled |  | D̅I̅S̅A̅B̅L̅E̅ = 5 V |  | 50 |  |  | 50 |  | nA |
| D̅I̅S̅A̅B̅L̅E̅ Pin Bias Current Disabled |  | D̅I̅S̅A̅B̅L̅E̅ = 0 V |  | 50 |  |  | 50 |  | nA |
| **$D_{GND}$ PIN** |  |  |  |  |  |  |  |  |  |
| VOLTAGE RANGE | $IVR_{DGND}$ |  | −$V_{S}$ |  | +$V_{S}$ − 2.5 | −$V_{S}$ |  | +$V_{S}$ − 2.5 | V |
| **POWER SUPPLY** |  |  |  |  |  |  |  |  |  |
| Operating Range | ±$V_{S}$ |  | 3 |  | 10 | 3 |  | 10 | V |
| Quiescent Current Enabled | $I_{q}$ | Full power mode, MODE = +$V_{S}$ |  | 4 | 4.2 |  |  |  | mA |
| Quiescent Current Enabled | $I_{q}$ | Low power mode, MODE = −$V_{S}$ |  |  |  |  | 1.4 | 1.6 | mA |
| Quiescent Current Disabled |  | Full power mode, MODE = +$V_{S}$ |  | 60 | 70 |  |  |  | µA |
| Quiescent Current Disabled |  | Low power mode, MODE = −$V_{S}$ |  |  |  |  | 60 | 70 | µA |
| +PSRR | +PSRR | Δ$V_{OS, dm}$/Δ$V_{S}$, Δ$V_{S}$ = 1 V p-p |  | -120 |  |  | -120 |  | dB |
| −PSRR | -PSRR | Δ$V_{OS, dm}$/Δ$V_{S}$, Δ$V_{S}$ = 1 V p-p |  | -120 |  |  | -120 |  | dB |
| OPERATING TEMPERATURE RANGE |  |  | -40 |  | +125 | -40 |  | +125 | °C |

**Table 7. +$D_{IN}$ or –$D_{IN}$ to $V_{OUT, DM}$ Performance** ([table-07-p15-spec.csv](ada4945-1/tables/table-07-p15-spec.csv), p. 15)

($V_{S}$ = 3 V $V_{OCM}$ = midsupply, G = 1, $R_{F}$ = $R_{G}$ = 499 Ω, $R_{L, dm}$ = 1 kΩ, $T_{A}$ = 25°C, unless otherwise noted. All specifications refer to single-ended input and differential outputs, unless otherwise noted. Refer to Figure 98 for circuit definitions.)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **DYNAMIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 1 |  | 145 |  |  | 80 |  | MHz |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 2 |  | 95 |  |  | 40 |  | MHz |
| −3 dB Small Signal Bandwidth | $f_{3dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 5 |  | 40 |  |  | 17 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, dm}$ = 2 V p-p, G = 1 |  | 22 |  |  | 11 |  | MHz |
| Bandwidth for 0.1 dB Flatness | $f_{0.1dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 1 |  | 28 |  |  | 27 |  | MHz |
| Bandwidth for 0.1 dB Flatness | $f_{0.1dB}$ | $V_{OUT, dm}$ = 20 mV p-p, G = 2 |  | 20 |  |  | 7 |  | MHz |
| Slew Rate | SR | $V_{OUT, dm}$ = 4 V step |  | 600 |  |  | 100 |  | V/µs |
| Settling Time to 0.1% | $t_{ST}$ | $V_{OUT, dm}$ = 4 V step |  | 35 |  |  | 85 |  | ns |
| Settling Time | $t_{ST}$ | 16-bit |  | 50 |  |  | 150 |  | ns |
| Settling Time | $t_{ST}$ | 18-bit |  | 100 |  |  | 300 |  | ns |
| Input Overdrive Recovery |  | G = 1, $V_{IN, dm}$ = 3 V p-p, triangular waveform |  | 500 |  |  | 300 |  | ns |
| Output Overdrive Recovery |  | G = 2, $V_{IN, dm}$ = 3 V p-p, triangular waveform |  | 200 |  |  | 120 |  | ns |
| **NOISE/HARMONIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| NOISE/HARMONIC PERFORMANCE |  | $V_{OUT, dm}$ = 4 V p-p |  |  |  |  |  |  |  |
| Second Harmonic Distortion | HD2 | Center frequency ($f_{C}$) = 1 kHz |  | -133 |  |  | -133 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 100 kHz |  | -133 |  |  | -133 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 100 kHz, G = 2 |  | -128 |  |  | -128 |  | dBc |
| Second Harmonic Distortion | HD2 | $f_{C}$ = 1 MHz |  | -95 |  |  | -68 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 1 kHz |  | -140 |  |  | -138 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 100 kHz |  | -116 |  |  | -116 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 100 kHz, G = 2 |  | -123 |  |  | -122 |  | dBc |
| Third Harmonic Distortion | HD3 | $f_{C}$ = 1 MHz |  | -88 |  |  | -62 |  | dBc |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | f = 10 Hz |  | 5 |  |  | 6 |  | nV/√Hz |
| Input Voltage Noise Differential | $V_{N, DIFF}$ | f = 100 kHz |  | 2.0 |  |  | 3.5 |  | nV/√Hz |
| Input Voltage Noise Differential |  | 1/f corner frequency |  | 100 |  |  | 40 |  | Hz |
| Common Mode | $V_{N, CM}$ | f = 10 Hz |  | 350 |  |  | 284 |  | nV/√Hz |
| Common Mode | $V_{N, CM}$ | f = 100 kHz |  | 30 |  |  | 38 |  | nV/√Hz |
| Common Mode |  | 1/f corner frequency |  | 1000 |  |  | 1000 |  | Hz |
| Integrated Voltage Noise |  | 0.1 Hz to 10 Hz |  | 35 |  |  | 35 |  | nV rms |
| Input Current Noise | $I_{N}$ | f = 10 Hz |  | 17 |  |  | 7 |  | pA/√Hz |
| Input Current Noise | $I_{N}$ | f = 100 kHz |  | 1.0 |  |  | 0.6 |  | pA/√Hz |
| Input Current Noise |  | 1/f corner frequency |  | 2000 |  |  | 1000 |  | Hz |
| **INPUT CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Input Offset Voltage | $V_{OS}$ | 25°C |  | ±10 | ±50 |  | ±10 | ±50 | µV |
| Input Offset Voltage | $V_{OS}$ | $T_{A}$ = 20°C to 85°C |  | ±15 | ±80 |  | ±15 | ±80 | µV |
| Input Offset Voltage | $V_{OS}$ | $T_{A}$ = −40°C to +125°C |  | ±30 | ±115 |  | ±30 | ±115 | µV |
| Input Offset Voltage Drift | $V_{OS\_TC}$ | $T_{A}$ = 20°C to 85°C |  | ±0.1 | ±0.5 |  | ±0.1 | ±0.5 | µV/°C |
| Input Offset Voltage Drift | $V_{OS\_TC}$ | $T_{A}$ = −40°C to +125°C |  | ±0.2 | ±1.0 |  | ±0.2 | ±1.0 | µV/°C |
| Input Bias Current | $I_{B}$ | $T_{A}$ = 25°C |  | −1.2 | −2.5 |  | −0.5 | −0.8 | µA |
| Input Bias Current | $I_{B}$ | $T_{A}$ = 20°C to 85°C |  | −1.5 | −3.0 |  | −0.6 | −1.0 | µA |
| Input Bias Current | $I_{B}$ | $T_{A}$ = −40°C to +125°C |  | −1.8 | −3.4 |  | −0.7 | −1.2 | µA |
| Input Bias Current Drift | $I_{B\_TC}$ | $T_{A}$ = 20°C to 85°C |  | −10 | −50 |  | −10 | −50 | nA/°C |
| Input Bias Current Drift | $I_{B\_TC}$ | $T_{A}$ = −40°C to +125°C |  | −10 | −50 |  | −10 | −50 | nA/°C |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = 25°C |  | ±20 | ±200 |  | ±10 | ±130 | nA |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = 20°C to 85°C |  | ±25 | ±250 |  | ±20 | ±150 | nA |
| Input Offset Current | $I_{OS}$ | $T_{A}$ = −40°C to +125°C |  | ±40 | ±300 |  | ±25 | ±200 | nA |
| Input Offset Current Drift | $I_{OS\_TC}$ | $T_{A}$ = 20°C to 85°C |  | ±0.1 | ±0.6 |  | ±0.06 | ±0.38 | nA/°C |
| Input Offset Current Drift | $I_{OS\_TC}$ | $T_{A}$ = −40°C to +125°C |  | ±0.12 | ±0.7 |  | ±0.07 | ±0.4 | nA/°C |
| $V_{CM}$ Range | $V_{CM}$ |  | −$V_{S}$ |  | +$V_{S}$ −1.3 | −$V_{S}$ |  | +$V_{S}$ −1.3 | V |
| Input Resistance | $R_{IN, DIFF}$ | Differential |  | 50 |  |  | 50 |  | kΩ |
| Input Resistance | $R_{IN, CM}$ | Common mode |  | 50 |  |  | 50 |  | MΩ |
| Input Capacitance | $C_{IN}$ |  |  | 1 |  |  | 1 |  | pF |
| CMRR |  | $V_{CM}$ = 0.5 V to 1.7 V |  | −110 |  |  | −110 |  | dB |
| Open-Loop Gain | $A_{OL}$ | $V_{OUT}$ = ±2 V |  | 120 |  |  | 115 |  | dB |
| **OUTPUT CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Output Voltage Swing | $V_{OUT}$ | $R_{L}$ = 100 Ω | −$V_{S}$ + 0.55 |  | +$V_{S}$ − 0.55 | −$V_{S}$ + 0.55 |  | +$V_{S}$ − 0.55 | V |
| Output Voltage Swing | $V_{OUT}$ | $R_{L}$ = 1 kΩ | −$V_{S}$ +0.1 |  | +$V_{S}$ − 0.1 | −$V_{S}$ +0.1 |  | +$V_{S}$ −0.1 | V |
| Short-Circuit Current | $I_{SC}$ |  |  | 170 |  |  | 140 |  | mA peak |
| Output Balance Error |  | f = 100 kHz, Δ$V_{OUT,cm}$/Δ$V_{OUT,dm}$ |  | 100 |  |  | 100 |  | dB |

**Table 8. $V_{OCM}$ to $V_{OUT, CM}$ Performance** ([table-08-p18-spec.csv](ada4945-1/tables/table-08-p18-spec.csv), p. 18)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **$V_{OCM}$ DYNAMIC PERFORMANCE** |  |  |  |  |  |  |  |  |  |
| −3 dB Small Signal Bandwidth | $f_{3dB, VOCM}$ | $V_{OUT, cm}$ = 20 mV p-p |  | 35 |  |  | 15 |  | MHz |
| −3 dB Large Signal Bandwidth |  | $V_{OUT, cm}$ = 2 V p-p |  | 3.8 |  |  | 1.3 |  | MHz |
| Slew Rate | $SR_{VOCM}$ | $V_{OUT, cm}$ = 2 V p-p |  | 26 |  |  | 9 |  | V/µs |
| Input Voltage Noise | $V_{N, VOCM}$ | f = 100 kHz |  | 35 |  |  | 45 |  | nV/√Hz |
| Gain |  | Δ$V_{OUT, cm}$/Δ$V_{OCM}$, Δ$V_{OCM}$ = ±1 V | 0.99 | 1 | 1.01 | 0.99 | 1 | 1.01 | V/V |
| **$V_{OCM}$ CHARACTERISTICS** |  |  |  |  |  |  |  |  |  |
| Input Common-Mode Voltage Range | $V_{OCM}$ |  | −$V_{S}$ +0.4 |  | +$V_{S}$ −1.4 | −$V_{S}$ +0.4 |  | +$V_{S}$ −1.4 | V |
| Input Resistance | $R_{IN, VOCM}$ |  |  | 125 |  |  | 125 |  | kΩ |
| Offset Voltage | $V_{OS, VOCM}$ | $V_{OS, cm}$ = $V_{OUT, cm}$ − $V_{OCM}$, $V_{IP}$ = $V_{IN}$ = $V_{OCM}$ = 0 V, 25°C |  | ±10 | ±60 |  | ±10 | ±60 | mV |
| Offset Voltage | $V_{OS, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | ±10 |  |  | ±10 |  | mV |
| Offset Voltage | $V_{OS, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | ±20 |  |  | ±20 |  | mV |
| Input Offset Voltage Drift | $V_{OS\_TC, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | ±5 |  |  | ±5 |  | µV/°C |
| Input Offset Voltage Drift | $V_{OS\_TC, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | ±10 |  |  | ±10 |  | µV/°C |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = 25°C |  | −220 |  |  | −160 |  | nA |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | −300 |  |  | −205 |  | nA |
| Input Bias Current | $I_{B, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | −350 |  |  | −230 |  | nA |
| Input Bias Current Drift | $I_{B\_TC, VOCM}$ | $T_{A}$ = 20°C to 85°C |  | −1.3 |  |  | −0.75 |  | nA/°C |
| Input Bias Current Drift | $I_{B\_TC, VOCM}$ | $T_{A}$ = −40°C to +125°C |  | −1.5 |  |  | −1.0 |  | nA/°C |
| CMRR | $CMRR_{VOCM}$ | Δ$V_{OS, dm}$/Δ$V_{OCM}$, Δ$V_{OCM}$ = ±1 V |  | −130 |  |  | −130 |  | dB |

**Table 9. General Performance** ([table-09-p19-spec.csv](ada4945-1/tables/table-09-p19-spec.csv), p. 19)

| PARAMETER | SYMBOL | TEST CONDITIONS/COMMENTS | FULL POWER MODE – MIN | FULL POWER MODE – TYP | FULL POWER MODE – MAX | LOW POWER MODE – MIN | LOW POWER MODE – TYP | LOW POWER MODE – MAX | UNIT |
|---|---|---|---|---|---|---|---|---|---|
| **CLAMP** |  |  |  |  |  |  |  |  |  |
| Clamp Output Voltage |  | Differential | −$V_{S}$ −0.5 |  | +$V_{S}$ +0.5 | −$V_{S}$ −0.5 |  | +$V_{S}$ +0.5 | V |
| Clamp Output Voltage |  | Common mode | −$V_{S}$ |  | +$V_{S}$ | −$V_{S}$ |  | +$V_{S}$ | V |
| Recovery Time |  |  |  | 100 |  |  | 100 |  | ns |
| Input Resistance |  | Resistance between +$V_{CLAMP}$ and −$V_{CLAMP}$ |  | 480 |  |  | 480 |  | kΩ |
| **DISABLE (D̅I̅S̅A̅B̅L̅E̅ PIN) MODE** |  |  |  |  |  |  |  |  |  |
| Input Voltage |  | Disabled | −$V_{S}$ −0.3 |  | $D_{GND}$ + 1 | −$V_{S}$ −0.3 |  | $D_{GND}$ + 1 | V |
| Input Voltage |  | Enabled | $D_{GND}$ +1.4 |  | +$V_{S}$ +0.3 | $D_{GND}$ +1.4 |  | +$V_{S}$ +0.3 | V |
| Turn Off Time | $t_{OFF}$ | Quiescent current<10% of enabled quiescent current |  | 6 |  |  | 6 |  | µs |
| Turn On Time | $t_{ON}$ | ($t_{O}$) >90% of final $V_{OUT}$ |  | 1.2 |  |  | 2 |  | µs |
| D̅I̅S̅A̅B̅L̅E̅ Pin Bias Current Enabled |  | D̅I̅S̅A̅B̅L̅E̅ = 3 V |  | 50 |  |  | 50 |  | nA |
| D̅I̅S̅A̅B̅L̅E̅ Pin Bias Current Disabled |  | D̅I̅S̅A̅B̅L̅E̅ = 0 V |  | 50 |  |  | 50 |  | nA |
| **$D_{GND}$ PIN** |  |  |  |  |  |  |  |  |  |
| VOLTAGE RANGE | $IVR_{DGND}$ |  | −$V_{S}$ |  | +$V_{S}$ − 2.5 | −$V_{S}$ |  | +$V_{S}$ − 2.5 | V |
| **POWER SUPPLY** |  |  |  |  |  |  |  |  |  |
| Operating Range | ±$V_{S}$ |  | 3 |  | 10 | 3 |  | 10 | V |
| Quiescent Current Enabled | $I_{q}$ | Full power mode, MODE = +$V_{S}$ |  | 4 | 4.2 |  |  |  | mA |
| Quiescent Current Enabled | $I_{q}$ | Low power mode, MODE = −$V_{S}$ |  |  |  |  | 1.4 | 1.6 | mA |
| Quiescent Current Disabled |  | Full power mode, MODE = +$V_{S}$ |  | 60 | 70 |  |  |  | µA |
| Quiescent Current Disabled |  | Low power mode, MODE = −$V_{S}$ |  |  |  |  | 60 | 70 | µA |
| +PSRR | +PSRR | Δ$V_{OS, dm}$/Δ$V_{S}$, Δ$V_{S}$ = 1 V p-p |  | -120 |  |  | -120 |  | dB |
| −PSRR | -PSRR | Δ$V_{OS, dm}$/Δ$V_{S}$, Δ$V_{S}$ = 1 V p-p |  | -120 |  |  | -120 |  | dB |
| OPERATING TEMPERATURE RANGE |  |  | -40 |  | +125 | -40 |  | +125 | °C |

### ABSOLUTE MAXIMUM RATINGS
<!-- pages: 21-22 -->

$T_{A}$ = 25°C unless otherwise specified.

**Table 10. Absolute Maximum Ratings** ([table-10-p21-abs_max.csv](ada4945-1/tables/table-10-p21-abs_max.csv), p. 21)

| PARAMETER | RATING |
|---|---|
| Supply Voltage | 11V |
| $V_{OCM}$ | ±$V_{S}$ |
| Differential Input Voltage | ±1V |
| Operating Temperature Range | −40°C to +125°C |
| Storage Temperature Range | −65°C to +150°C |
| Lead Temperature (Soldering, 10 sec) | 300°C |
| Junction Temperature | 150°C |
| Electrostatic Discharge (ESD) Field Induced Charged Device Model (FICDM) | 1250V |
| Electrostatic Discharge (ESD)Human Body Model (HBM) | 4000V |

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

#### Thermal Resistance
<!-- page: 21 -->

Thermal performance is directly linked to printed circuit board (PCB) design and operating environment. Careful attention to PCB thermal design is required.

$\theta_{JA}$ is the natural convection, junction to ambient, thermal resistance measured in a one cubic foot sealed enclosure. $\theta_{JC}$ is the junction to case thermal resistance.

**Table 11. Thermal Resistance** ([table-11-p21-data.csv](ada4945-1/tables/table-11-p21-data.csv), p. 21)

| Package Type | $\theta_{JA}$ | $\theta_{JC}$ | Unit |
|---|---|---|---|
| CP-16-22 | 70 | 15 | °C/W |

#### Maximum Power Dissipation
<!-- page: 21 -->

The maximum safe power dissipation in the ADA4945-1 package is limited by the associated rise in junction temperature ($T_{J}$) on the die. At approximately 150°C, which is the glass transition temperature, the properties of the plastic change. Even temporarily exceeding this temperature limit can change the stresses that the package exerts on the die, permanently shifting the parametric performance of ADA4945-1. Exceeding a junction temperature of 150°C for an extended period can result in changes in the silicon devices, potentially causing failure.

The power dissipated in the package (PD) is the sum of the quiescent power dissipation and the power dissipated in the package due to the load drive for all outputs. The quiescent power dissipation is the voltage between the supply pins (±$V_{S}$) times the quiescent current ($I_{q}$). The load current consists of the differential and common-mode currents flowing to the load, as well as currents flowing through the external feedback networks and internal common-mode feedback loop. The internal resistor tap used in the common-mode feedback loop places a negligible differential load on the output. Consider RMS voltages and currents when dealing with ac signals.

Airflow reduces $\theta_{JA}$. In addition, more metal directly in contact with the package leads from metal traces through holes, ground, and power planes reduces the $\theta_{JA}$.

Figure 2 shows the maximum safe power dissipation in the package vs. the ambient temperature for the 16-lead LFCSP ($\theta_{JA}$ = 70°C/W) package on a JEDEC standard 4-layer board. $\theta_{JA}$ values are approximations.

![Figure 2. Maximum Safe Power Dissipation vs. Ambient Temperature](ada4945-1/figures/ada4945-1-f004.png)

*Figure 2. Maximum Safe Power Dissipation vs. Ambient Temperature*

Digitized data: [maximum-safe-power-dissipation-vs-ambient-temperature.csv](ada4945-1/curves/maximum-safe-power-dissipation-vs-ambient-temperature.csv) (x: °C; y: W) — values read off the printed plot by the digitizer, not published data.

#### ESD Caution
<!-- page: 22 -->

**ESD (electrostatic discharge) sensitive device.** Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

### PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
<!-- page: 23 -->

![Figure 3. Pin Configuration](ada4945-1/figures/ada4945-1-f005.png)

*Figure 3. Pin Configuration*

**Table 12.Pin Descriptions** ([table-12-p23-pin.csv](ada4945-1/tables/table-12-p23-pin.csv), p. 23)

| PIN | NAME | DESCRIPTION |
|---|---|---|
| 1 | −FB | Negative Output for Feedback Component Connection. |
| 2 | +IN | Positive Input Summing Node. |
| 3 | −IN | Negative Input Summing Node. |
| 4 | +FB | Positive Output for Feedback Component Connection. |
| 5 | MODE | Selects Between Full Power Mode and Low Power Mode. |
| 6, 7 | +$V_{S}$ | Positive Supply Voltage. |
| 8 | +$V_{CLAMP}$ | Positive Clamp Level. |
| 9 | $V_{OCM}$ | Output Common-Mode Voltage. |
| 10 | +OUT | Positive Output for Load Connection. |
| 11 | −OUT | Negative Output for Load Connection. |
| 12 | D̅I̅S̅A̅B̅L̅E̅ | Disable Pin. |
| 13 | −$V_{CLAMP}$ | Negative Clamp Level. |
| 14, 15 | −$V_{S}$ | Negative Supply Voltage. |
| 16 | $D_{GND}$ | Digital Ground Level. |
|  | Exposed pad (EPAD) | Exposed Pad. Connect the exposed pad to −$V_{S}$. |

### TYPICAL PERFORMANCE CHARACTERISTICS (FULL POWER MODE)
<!-- pages: 24-31 -->

($T_{A}$ = +25°C, $V_{S}$ = ±5 V, G = 1, $R_{F}$ = $R_{G}$ = 499 Ω, $R_{T}$ = 53.6 Ω (when used), and $R_{L}$ = 1 kΩ, unless otherwise noted. See Figure 94, Figure 95, Figure 96, and Figure 97 for the test circuits.)

![Figure 4. Small Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f006.png)

*Figure 4. Small Signal Frequency Response for Various Gains and Loads*

![Figure 5. Small Signal Frequency Response for Various Supplies](ada4945-1/figures/ada4945-1-f007.png)

*Figure 5. Small Signal Frequency Response for Various Supplies*

![Figure 6. Small Signal Frequency Response for Various Temperatures](ada4945-1/figures/ada4945-1-f008.png)

*Figure 6. Small Signal Frequency Response for Various Temperatures*

![Figure 7. Large Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f009.png)

*Figure 7. Large Signal Frequency Response for Various Gains and Loads*

![Figure 8. Large Signal Frequency Response for Various Supplies](ada4945-1/figures/ada4945-1-f010.png)

*Figure 8. Large Signal Frequency Response for Various Supplies*

![Figure 9.Large Signal Frequency Response for Various Temperatures](ada4945-1/figures/ada4945-1-f011.png)

*Figure 9.Large Signal Frequency Response for Various Temperatures*

![Figure 10. Small Signal Frequency Response at Various VOCM Levels](ada4945-1/figures/ada4945-1-f012.png)

*Figure 10. Small Signal Frequency Response at Various $V_{OCM}$ Levels*

![Figure 11. Large Signal Frequency Response at Various VOCM Levels](ada4945-1/figures/ada4945-1-f013.png)

*Figure 11. Large Signal Frequency Response at Various $V_{OCM}$ Levels*

![Figure 12. Small Signal Frequency Response for Various Capacitive Loads](ada4945-1/figures/ada4945-1-f014.png)

*Figure 12. Small Signal Frequency Response for Various Capacitive Loads*

![Figure 13. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f015.png)

*Figure 13. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads*

![Figure 14. VOCM Small Signal Frequency Response](ada4945-1/figures/ada4945-1-f016.png)

*Figure 14. $V_{OCM}$ Small Signal Frequency Response*

Digitized data: [v-ocm-small-signal-frequency-response.csv](ada4945-1/curves/v-ocm-small-signal-frequency-response.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 15. Large Signal Frequency Response for Various Capacitive Loads](ada4945-1/figures/ada4945-1-f017.png)

*Figure 15. Large Signal Frequency Response for Various Capacitive Loads*

![Figure 16. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f018.png)

*Figure 16. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads*

![Figure 17. VOCM Large Signal Frequency Response](ada4945-1/figures/ada4945-1-f019.png)

*Figure 17. $V_{OCM}$ Large Signal Frequency Response*

Digitized data: [vocm-large-signal-frequency-response.csv](ada4945-1/curves/vocm-large-signal-frequency-response.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 18. Input Offset Voltage vs. Temperature for 50 Devices](ada4945-1/figures/ada4945-1-f020.png)

*Figure 18. Input Offset Voltage vs. Temperature for 50 Devices*

![Figure 19. Input Offset Current vs. Temperature for 30 Devices](ada4945-1/figures/ada4945-1-f021.png)

*Figure 19. Input Offset Current vs. Temperature for 30 Devices*

![Figure 20. Harmonic Distortion vs. Frequency for Various Loads](ada4945-1/figures/ada4945-1-f022.png)

*Figure 20. Harmonic Distortion vs. Frequency for Various Loads*

![Figure 21. Harmonic Distortion vs. Frequency for Various Supplies](ada4945-1/figures/ada4945-1-f023.png)

*Figure 21. Harmonic Distortion vs. Frequency for Various Supplies*

![Figure 22. Harmonic Distortion vs. Frequency for Various Gains](ada4945-1/figures/ada4945-1-f024.png)

*Figure 22. Harmonic Distortion vs. Frequency for Various Gains*

![Figure 23. Harmonic Distortion vs. VOCM, f = 1 kHz, ±5 V Supplies](ada4945-1/figures/ada4945-1-f025.png)

*Figure 23. Harmonic Distortion vs. $V_{OCM}$, f = 1 kHz, ±5 V Supplies*

![Figure 24. Harmonic Distortion vs. VOCM, f = 1 kHz, ±2.5 V Supplies](ada4945-1/figures/ada4945-1-f026.png)

*Figure 24. Harmonic Distortion vs. $V_{OCM}$, f = 1 kHz, ±2.5 V Supplies*

![Figure 25. Harmonic Distortion vs. Frequency for Various VOUT, dm](ada4945-1/figures/ada4945-1-f027.png)

*Figure 25. Harmonic Distortion vs. Frequency for Various $V_{OUT, dm}$*

![Figure 26. Harmonic Distortion vs. VOUT, dm for Various Supplies, f = 1 kHz](ada4945-1/figures/ada4945-1-f028.png)

*Figure 26. Harmonic Distortion vs. $V_{OUT, dm}$ for Various Supplies, f = 1 kHz*

![Figure27. Harmonic Distortion vs. Frequency for Various RF and RG Values](ada4945-1/figures/ada4945-1-f029.png)

*Figure27. Harmonic Distortion vs. Frequency for Various $R_{F}$ and $R_{G}$ Values*

Digitized data: [figure27-harmonic-distortion-vs-frequency-for-various-rf-and-r-g-values.csv](ada4945-1/curves/figure27-harmonic-distortion-vs-frequency-for-various-rf-and-r-g-values.csv) (x: Hz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 28. CMRR vs. Frequency](ada4945-1/figures/ada4945-1-f105.png)

*Figure 28. CMRR vs. Frequency*

![Figure 29. Output Balance vs. Frequency](ada4945-1/figures/ada4945-1-f107.png)

*Figure 29. Output Balance vs. Frequency*

![Figure 30. PSRR vs. Frequency](ada4945-1/figures/ada4945-1-f109.png)

*Figure 30. PSRR vs. Frequency*

![Figure 31. Open-Loop Gain and Phase vs. Frequency](ada4945-1/figures/ada4945-1-f106.png)

*Figure 31. Open-Loop Gain and Phase vs. Frequency*

![Figure 32. Output Overdrive Recovery, G = 2](ada4945-1/figures/ada4945-1-f108.png)

*Figure 32. Output Overdrive Recovery, G = 2*

![Figure 33. Voltage Noise Spectral Density, Referred to Input](ada4945-1/figures/ada4945-1-f110.png)

*Figure 33. Voltage Noise Spectral Density, Referred to Input*

![Figure 34. Input Current Noise Spectral Density](ada4945-1/figures/ada4945-1-f031.png)

*Figure 34. Input Current Noise Spectral Density*

Digitized data: [input-current-noise-spectral-density.csv](ada4945-1/curves/input-current-noise-spectral-density.csv) (x: Hz; y: pA/√Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 35. DISABLE Pin Turn-Off Time](ada4945-1/figures/ada4945-1-f032.png)

*Figure 35. D̅I̅S̅A̅B̅L̅E̅ Pin Turn-Off Time*

![Figure 36. 0.1% Settling Time](ada4945-1/figures/ada4945-1-f033.png)

*Figure 36. 0.1% Settling Time*

![Figure 37. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1](ada4945-1/figures/ada4945-1-f034.png)

*Figure 37. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1*

![Figure 38. DISABLE Pin Turn-On Time](ada4945-1/figures/ada4945-1-f035.png)

*Figure 38. D̅I̅S̅A̅B̅L̅E̅ Pin Turn-On Time*

![Figure 39. Small Signal Transient Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f036.png)

*Figure 39. Small Signal Transient Response for Various Gains and Loads*

![Figure 40. Small Signal Transient Response for Various Capacitive Loads, VS =10V](ada4945-1/figures/ada4945-1-f037.png)

*Figure 40. Small Signal Transient Response for Various Capacitive Loads, $V_{S}$ =10V*

Digitized data: [small-signal-transient-response-for-various-capacitive-loads-vs-10v.csv](ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-vs-10v.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 41. Small Signal Transient Response for Various Capacitive Loads, VS=5V](ada4945-1/figures/ada4945-1-f038.png)

*Figure 41. Small Signal Transient Response for Various Capacitive Loads, $V_{S}$=5V*

![Figure 42. Small Signal Transient Response for Various Capacitive Loads, VS = 3V](ada4945-1/figures/ada4945-1-f039.png)

*Figure 42. Small Signal Transient Response for Various Capacitive Loads, $V_{S}$ = 3V*

![Figure 43. Large Signal Transient Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f040.png)

*Figure 43. Large Signal Transient Response for Various Gains and Loads*

![Figure 44. Large Signal Transient Response for Various Capacitive Loads, VS = 10 V](ada4945-1/figures/ada4945-1-f041.png)

*Figure 44. Large Signal Transient Response for Various Capacitive Loads, $V_{S}$ = 10 V*

Digitized data: [large-signal-transient-response-for-various-capacitive-loads-v-s-10-v.csv](ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-10-v.csv) (x: ns; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 45. Large Signal Transient Response for Various Capacitive Loads, VS= 5V](ada4945-1/figures/ada4945-1-f042.png)

*Figure 45. Large Signal Transient Response for Various Capacitive Loads, $V_{S}$= 5V*

![Figure 46. Large Signal Transient Response for Various Capacitive Loads, VS=3V](ada4945-1/figures/ada4945-1-f043.png)

*Figure 46. Large Signal Transient Response for Various Capacitive Loads, $V_{S}$=3V*

![Figure 47. VOCM Small Signal Transient Response](ada4945-1/figures/ada4945-1-f044.png)

*Figure 47. $V_{OCM}$ Small Signal Transient Response*

![Figure 48. VOCM Large Signal Transient Response](ada4945-1/figures/ada4945-1-f045.png)

*Figure 48. $V_{OCM}$ Large Signal Transient Response*

### TYPICAL PERFORMANCE CHARACTERISTICS (LOW POWER MODE)
<!-- pages: 32-39 -->

![Figure 49. Small Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f046.png)

*Figure 49. Small Signal Frequency Response for Various Gains and Loads*

Digitized data: [small-signal-frequency-response-for-various-gains-and-loads.csv](ada4945-1/curves/small-signal-frequency-response-for-various-gains-and-loads.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 50. Small Signal Frequency Response for Various Supplies](ada4945-1/figures/ada4945-1-f047.png)

*Figure 50. Small Signal Frequency Response for Various Supplies*

Digitized data: [small-signal-frequency-response-for-various-supplies.csv](ada4945-1/curves/small-signal-frequency-response-for-various-supplies.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 51. Small Signal Frequency Response for Various Temperatures](ada4945-1/figures/ada4945-1-f048.png)

*Figure 51. Small Signal Frequency Response for Various Temperatures*

Digitized data: [small-signal-frequency-response-for-various-temperatures.csv](ada4945-1/curves/small-signal-frequency-response-for-various-temperatures.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 52. Large Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f049.png)

*Figure 52. Large Signal Frequency Response for Various Gains and Loads*

Digitized data: [large-signal-frequency-response-for-various-gains-and-loads.csv](ada4945-1/curves/large-signal-frequency-response-for-various-gains-and-loads.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 53. Large Signal Frequency Response for Various Supplies](ada4945-1/figures/ada4945-1-f050.png)

*Figure 53. Large Signal Frequency Response for Various Supplies*

Digitized data: [large-signal-frequency-response-for-various-supplies.csv](ada4945-1/curves/large-signal-frequency-response-for-various-supplies.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 54. Large Signal Frequency Response for Various Temperatures](ada4945-1/figures/ada4945-1-f051.png)

*Figure 54. Large Signal Frequency Response for Various Temperatures*

Digitized data: [large-signal-frequency-response-for-various-temperatures.csv](ada4945-1/curves/large-signal-frequency-response-for-various-temperatures.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 55. Small Signal Frequency Response at Various VOCM Levels](ada4945-1/figures/ada4945-1-f052.png)

*Figure 55. Small Signal Frequency Response at Various $V_{OCM}$ Levels*

Digitized data: [small-signal-frequency-response-at-various-vocm-levels.csv](ada4945-1/curves/small-signal-frequency-response-at-various-vocm-levels.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 56. Large Signal Frequency Response at Various VOCM Levels](ada4945-1/figures/ada4945-1-f053.png)

*Figure 56. Large Signal Frequency Response at Various $V_{OCM}$ Levels*

Digitized data: [large-signal-frequency-response-at-various-vocm-levels.csv](ada4945-1/curves/large-signal-frequency-response-at-various-vocm-levels.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 57. Small Signal Frequency Response for Various Capacitive Loads](ada4945-1/figures/ada4945-1-f054.png)

*Figure 57. Small Signal Frequency Response for Various Capacitive Loads*

Digitized data: [small-signal-frequency-response-for-various-capacitive-loads.csv](ada4945-1/curves/small-signal-frequency-response-for-various-capacitive-loads.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 58. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f055.png)

*Figure 58. 0.1 dB Flatness Small Signal Frequency Response for Various Gains and Loads*

Digitized data: [0-1-db-flatness-small-signal-frequency-response-for-various-gains-and-loads.csv](ada4945-1/curves/0-1-db-flatness-small-signal-frequency-response-for-various-gains-and-loads.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 59. VOCM Small Signal Frequency](ada4945-1/figures/ada4945-1-f056.png)

*Figure 59. $V_{OCM}$ Small Signal Frequency*

Digitized data: [v-ocm-small-signal-frequency.csv](ada4945-1/curves/v-ocm-small-signal-frequency.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 60. Large Signal Frequency Response for Various Capacitive Loads](ada4945-1/figures/ada4945-1-f057.png)

*Figure 60. Large Signal Frequency Response for Various Capacitive Loads*

Digitized data: [large-signal-frequency-response-for-various-capacitive-loads.csv](ada4945-1/curves/large-signal-frequency-response-for-various-capacitive-loads.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 61. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f058.png)

*Figure 61. 0.1 dB Flatness Large Signal Frequency Response for Various Gains and Loads*

Digitized data: [0-1-db-flatness-large-signal-frequency-response-for-various-gains-and-loads.csv](ada4945-1/curves/0-1-db-flatness-large-signal-frequency-response-for-various-gains-and-loads.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 62. VOCM Large Signal Frequency](ada4945-1/figures/ada4945-1-f059.png)

*Figure 62. $V_{OCM}$ Large Signal Frequency*

Digitized data: [v-ocm-large-signal-frequency.csv](ada4945-1/curves/v-ocm-large-signal-frequency.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 63. Input Offset Voltage vs. Temperature for 50 Devices](ada4945-1/figures/ada4945-1-f060.png)

*Figure 63. Input Offset Voltage vs. Temperature for 50 Devices*

Digitized data: [input-offset-voltage-vs-temperature-for-50-devices.csv](ada4945-1/curves/input-offset-voltage-vs-temperature-for-50-devices.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 64. Input Offset Current vs. Temperature for 30 Devices](ada4945-1/figures/ada4945-1-f061.png)

*Figure 64. Input Offset Current vs. Temperature for 30 Devices*

Digitized data: [input-offset-current-vs-temperature-for-30-devices.csv](ada4945-1/curves/input-offset-current-vs-temperature-for-30-devices.csv) (x: °C; y: nA) — values read off the printed plot by the digitizer, not published data.

![Figure 65. Harmonic Distortion vs. Frequency for Various Loads](ada4945-1/figures/ada4945-1-f062.png)

*Figure 65. Harmonic Distortion vs. Frequency for Various Loads*

Digitized data: [harmonic-distortion-vs-frequency-for-various-loads.csv](ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-loads.csv) (x: Hz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 66. Harmonic Distortion vs. Frequency for Various Supplies](ada4945-1/figures/ada4945-1-f063.png)

*Figure 66. Harmonic Distortion vs. Frequency for Various Supplies*

Digitized data: [harmonic-distortion-vs-frequency-for-various-supplies.csv](ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-supplies.csv) (x: Hz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 67. Harmonic Distortion vs. Frequency for Various Gains](ada4945-1/figures/ada4945-1-f064.png)

*Figure 67. Harmonic Distortion vs. Frequency for Various Gains*

Digitized data: [harmonic-distortion-vs-frequency-for-various-gains.csv](ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-gains.csv) (x: Hz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 68. Harmonic Distortion vs. VOCM, f = 1 kHz, ±5 V Supplies](ada4945-1/figures/ada4945-1-f065.png)

*Figure 68. Harmonic Distortion vs. $V_{OCM}$, f = 1 kHz, ±5 V Supplies*

Digitized data: [harmonic-distortion-vs-v-ocm-f-1-khz-5-v-supplies.csv](ada4945-1/curves/harmonic-distortion-vs-v-ocm-f-1-khz-5-v-supplies.csv) (x: V; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 69. Harmonic Distortion vs. VOCM, f = 1 kHz, ±2.5 V Supplies](ada4945-1/figures/ada4945-1-f066.png)

*Figure 69. Harmonic Distortion vs. $V_{OCM}$, f = 1 kHz, ±2.5 V Supplies*

Digitized data: [harmonic-distortion-vs-v-ocm-f-1-khz-2-5-v-supplies.csv](ada4945-1/curves/harmonic-distortion-vs-v-ocm-f-1-khz-2-5-v-supplies.csv) (x: V; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 70. Harmonic Distortion vs. Frequency for Various VOUT, dm](ada4945-1/figures/ada4945-1-f067.png)

*Figure 70. Harmonic Distortion vs. Frequency for Various $V_{OUT, dm}$*

Digitized data: [harmonic-distortion-vs-frequency-for-various-v-out-dm.csv](ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-v-out-dm.csv) (x: Hz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 71. Harmonic Distortion vs. VOUT, dm for Various Supplies, f = 1 kHz](ada4945-1/figures/ada4945-1-f068.png)

*Figure 71. Harmonic Distortion vs. $V_{OUT, dm}$ for Various Supplies, f = 1 kHz*

Digitized data: [harmonic-distortion-vs-v-out-dm-for-various-supplies-f-1-khz.csv](ada4945-1/curves/harmonic-distortion-vs-v-out-dm-for-various-supplies-f-1-khz.csv) (x: V p-p; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 72. Harmonic Distortion vs. Frequency for Various RF and RG Values](ada4945-1/figures/ada4945-1-f069.png)

*Figure 72. Harmonic Distortion vs. Frequency for Various $R_{F}$ and $R_{G}$ Values*

Digitized data: [harmonic-distortion-vs-frequency-for-various-rf-and-r-g-values.csv](ada4945-1/curves/harmonic-distortion-vs-frequency-for-various-rf-and-r-g-values.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 73. CMRR vs. Frequency](ada4945-1/figures/ada4945-1-f111.png)

*Figure 73. CMRR vs. Frequency*

Digitized data: [cmrr-vs-frequency.csv](ada4945-1/curves/cmrr-vs-frequency.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 74. Output Balance vs. Frequency](ada4945-1/figures/ada4945-1-f113.png)

*Figure 74. Output Balance vs. Frequency*

Digitized data: [output-balance-vs-frequency.csv](ada4945-1/curves/output-balance-vs-frequency.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 75. PSRR vs. Frequency](ada4945-1/figures/ada4945-1-f115.png)

*Figure 75. PSRR vs. Frequency*

Digitized data: [psrr-vs-frequency.csv](ada4945-1/curves/psrr-vs-frequency.csv) (x: MHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 76. Open-Loop Gain and Phase vs. Frequency](ada4945-1/figures/ada4945-1-f112.png)

*Figure 76. Open-Loop Gain and Phase vs. Frequency*

Digitized data: [open-loop-gain-and-phase-vs-frequency.csv](ada4945-1/curves/open-loop-gain-and-phase-vs-frequency.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 77. Output Overdrive Recovery, G = 2](ada4945-1/figures/ada4945-1-f114.png)

*Figure 77. Output Overdrive Recovery, G = 2*

Digitized data: [output-overdrive-recovery-g-2.csv](ada4945-1/curves/output-overdrive-recovery-g-2.csv) (x: us; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 78. Voltage Noise Spectral Density, Referred to Input](ada4945-1/figures/ada4945-1-f116.png)

*Figure 78. Voltage Noise Spectral Density, Referred to Input*

Digitized data: [voltage-noise-spectral-density-referred-to-input.csv](ada4945-1/curves/voltage-noise-spectral-density-referred-to-input.csv) (x: Hz; y: nV/√Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 79. Current Noise Spectral Density](ada4945-1/figures/ada4945-1-f071.png)

*Figure 79. Current Noise Spectral Density*

Digitized data: [current-noise-spectral-density.csv](ada4945-1/curves/current-noise-spectral-density.csv) (x: Hz; y: pA/√Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 80. DISABLE Pin Turn-Off Time](ada4945-1/figures/ada4945-1-f072.png)

*Figure 80. D̅I̅S̅A̅B̅L̅E̅ Pin Turn-Off Time*

Digitized data: [disable-pin-turn-off-time.csv](ada4945-1/curves/disable-pin-turn-off-time.csv) (x: µs; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 81. 0.1% Settling Time](ada4945-1/figures/ada4945-1-f073.png)

*Figure 81. 0.1% Settling Time*

Digitized data: [0-1-settling-time.csv](ada4945-1/curves/0-1-settling-time.csv) (x: ns; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 82. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1](ada4945-1/figures/ada4945-1-f074.png)

*Figure 82. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1*

Digitized data: [closed-loop-output-impedance-magnitude-vs-frequency-g-1.csv](ada4945-1/curves/closed-loop-output-impedance-magnitude-vs-frequency-g-1.csv) (x: MHz; y: Ω) — values read off the printed plot by the digitizer, not published data.

![Figure 83. DISABLE Pin Turn-On Time](ada4945-1/figures/ada4945-1-f075.png)

*Figure 83. D̅I̅S̅A̅B̅L̅E̅ Pin Turn-On Time*

Digitized data: [disable-pin-turn-on-time.csv](ada4945-1/curves/disable-pin-turn-on-time.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 84. Small Signal Transient Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f076.png)

*Figure 84. Small Signal Transient Response for Various Gains and Loads*

Digitized data: [small-signal-transient-response-for-various-gains-and-loads.csv](ada4945-1/curves/small-signal-transient-response-for-various-gains-and-loads.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 85. Small Signal Transient Response for Various Capacitive Loads, VS= 10V](ada4945-1/figures/ada4945-1-f077.png)

*Figure 85. Small Signal Transient Response for Various Capacitive Loads, $V_{S}$= 10V*

Digitized data: [small-signal-transient-response-for-various-capacitive-loads-v-s-10v.csv](ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-v-s-10v.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 86. Small Signal Transient Response for Various Capacitive Loads, VS= 5V](ada4945-1/figures/ada4945-1-f078.png)

*Figure 86. Small Signal Transient Response for Various Capacitive Loads, $V_{S}$= 5V*

Digitized data: [small-signal-transient-response-for-various-capacitive-loads-v-s-5v.csv](ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-v-s-5v.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 87. Small Signal Transient Response for Various Capacitive Loads, VS=3V](ada4945-1/figures/ada4945-1-f079.png)

*Figure 87. Small Signal Transient Response for Various Capacitive Loads, $V_{S}$=3V*

Digitized data: [small-signal-transient-response-for-various-capacitive-loads-v-s-3v.csv](ada4945-1/curves/small-signal-transient-response-for-various-capacitive-loads-v-s-3v.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 88. Large Signal Transient Response for Various Gains and Loads](ada4945-1/figures/ada4945-1-f080.png)

*Figure 88. Large Signal Transient Response for Various Gains and Loads*

Digitized data: [large-signal-transient-response-for-various-gains-and-loads.csv](ada4945-1/curves/large-signal-transient-response-for-various-gains-and-loads.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 89. Large Signal Transient Response for Various Capacitive Loads, VS= 10V](ada4945-1/figures/ada4945-1-f081.png)

*Figure 89. Large Signal Transient Response for Various Capacitive Loads, $V_{S}$= 10V*

Digitized data: [large-signal-transient-response-for-various-capacitive-loads-v-s-10v.csv](ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-10v.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 90. Large Signal Transient Response for Various Capacitive Loads, VS= 5V](ada4945-1/figures/ada4945-1-f082.png)

*Figure 90. Large Signal Transient Response for Various Capacitive Loads, $V_{S}$= 5V*

Digitized data: [large-signal-transient-response-for-various-capacitive-loads-v-s-5v.csv](ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-5v.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 91. Large Signal Transient Response for Various Capacitive Loads, VS=3V](ada4945-1/figures/ada4945-1-f083.png)

*Figure 91. Large Signal Transient Response for Various Capacitive Loads, $V_{S}$=3V*

Digitized data: [large-signal-transient-response-for-various-capacitive-loads-v-s-3v.csv](ada4945-1/curves/large-signal-transient-response-for-various-capacitive-loads-v-s-3v.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 92. VOCM Small Signal Transient Response](ada4945-1/figures/ada4945-1-f084.png)

*Figure 92. $V_{OCM}$ Small Signal Transient Response*

Digitized data: [v-ocm-small-signal-transient-response.csv](ada4945-1/curves/v-ocm-small-signal-transient-response.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 93. VOCM Large Signal Transient Response](ada4945-1/figures/ada4945-1-f085.png)

*Figure 93. $V_{OCM}$ Large Signal Transient Response*

Digitized data: [v-ocm-large-signal-transient-response.csv](ada4945-1/curves/v-ocm-large-signal-transient-response.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

### TEST CIRCUITS
<!-- page: 40 -->

![Figure 94. Equivalent Basic Test Circuit](ada4945-1/figures/ada4945-1-f123.png)

*Figure 94. Equivalent Basic Test Circuit*

![Figure 95. Test Circuit for Distortion Measurements](ada4945-1/figures/ada4945-1-f117-01.png)

*Figure 95. Test Circuit for Distortion Measurements*

![Figure 96. Test Circuit for DISABLE Pin Turn Off Time Measurement](ada4945-1/figures/ada4945-1-f117-02.png)

*Figure 96. Test Circuit for D̅I̅S̅A̅B̅L̅E̅ Pin Turn Off Time Measurement*

![Figure 97. Test Circuit for DISABLE Pin Turn On Time Measurement](ada4945-1/figures/ada4945-1-f118.png)

*Figure 97. Test Circuit for D̅I̅S̅A̅B̅L̅E̅ Pin Turn On Time Measurement*

### TERMINOLOGY
<!-- pages: 41-42 -->

#### Differential Voltage
<!-- page: 41 -->

Differential voltage is the difference between two node voltages. For example, the differential output voltage (or equivalently, output differential mode voltage) is defined as

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq01.png)

$$V_{OUT , dm} = ( V_{+ OUT} - V_{-OUT} )$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where $V_{+OUT}$ and $V_{-OUT}$ refer to the voltages at the +OUT and −OUT terminals with respect to a common reference. Similarly, the differential input voltage is defined as

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq02.png)

$$V_{IN , dm} = ( + D_{IN} - ( - D_{IN} ) )$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Common-Mode Voltage (CMV)
<!-- page: 41 -->

CMV is the average of two node voltages. The output common mode voltage is defined as

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq03.png)

$$V_{OUT , cm} = ( V_{+OUT} + V_{-OUT} ) / 2$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Similarly, the input common-mode voltage is defined as

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq04.png)

$$V_{IN , cm} = ( + D_{IN} + ( - D_{IN} ) ) / 2$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Common-Mode Offset Voltage
<!-- page: 41 -->

Common-mode offset voltage is the difference between the voltage applied to the VOCM terminal and the common mode of the output voltage.

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq05.png)

$$V_{OS , cm} = V_{OUT , cm} - V_{OCM}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Differential $V_{OS}$, Differential CMRR, and $V_{OCM}$ CMRR
<!-- page: 41 -->

The differential mode and common-mode voltages each have their own error sources. The differential offset ($V_{OS, dm}$) is the voltage error between the +IN and −IN terminals of the amplifier. Differential CMRR reflects the change of $V_{OS}$, dm in response to changes to the common-mode voltage at +$D_{IN}$ and −$D_{IN}$ (see Figure 98).

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq06.png)

$$CMRR_{DFF} = \frac{\Delta V_{IN , cm}}{\Delta V_{OS , dm}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

$V_{OCM}$ CMRR reflects the change of VOS, dm in response to changes to the common-mode voltage at the output terminals.

![Equation as printed (p. 41)](ada4945-1/figures/ada4945-1-eq07.png)

$$\text{CMRR}_{V_{OCM}} = \frac{\Delta V_{OCM}}{\Delta V_{OS,dm}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Balance
<!-- page: 42 -->

Balance is a measure of how well the differential signals are matched in amplitude. The differential signals are exactly 180° apart in phase. By this definition, the output balance is the magnitude of the output common-mode voltage divided by the magnitude of the output differential mode voltage.

![Equation as printed (p. 42)](ada4945-1/figures/ada4945-1-eqx02.png)

$$\text{Output Balance Error} = \left| \frac{V_{OUT,cm}}{V_{OUT,dm}} \right|$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Figure 98. Circuit Definitions](ada4945-1/figures/ada4945-1-f087.png)

*Figure 98. Circuit Definitions*

### THEORY OF OPERATION
<!-- pages: 43-45 -->

![Figure 99. ADA4945-1 Architectural Block Diagram](ada4945-1/figures/ada4945-1-f088.png)

*Figure 99. ADA4945-1 Architectural Block Diagram*

The ADA4945-1 is a high speed, low power differential amplifier fabricated on Analog Devices advanced dielectrically isolated SiGe bipolar process. The device provides two closely balanced differential outputs in response to either differential or single-ended input signals. An external feedback network that is similar to a voltage feedback operational amplifier sets the differential gain. The output common-mode voltage is independent of the input common-mode voltage and is set by an external voltage at the $V_{OCM}$ terminal. The PNP input stage allows input common-mode voltages between the negative supply and 1.3 V less than the positive supply. A rail-to-rail output stage supplies a wide output voltage range. The D̅I̅S̅A̅B̅L̅E̅ pin can reduce the supply current ($I_{q}$) of the amplifier to 50 µA.

#### Fully Differential and Common-Mode Signal Paths
<!-- page: 43 -->

Figure 99 shows a simplified diagram of the ADA4945-1 architecture. The differential feedback loop consists of the differential transconductance ($G_{DIFF}$) working through the $G_{O}$ output buffers and the $R_{F}$/$R_{G}$ feedback networks. The common-mode feedback loop is set up with a voltage divider across the two differential outputs to create an output voltage midpoint ($V_{OUT(CM)}$) and a common-mode transconductance ($G_{CM}$).

The differential feedback loop forces the voltages at +IN and −IN to equal each other. This voltage equalization sets the following relationships:

![Equation as printed (p. 43)](ada4945-1/figures/ada4945-1-eq08.png)

$$\frac{+D_{IN}}{R_G} = -\frac{V_{-OUT}}{R_F}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 43)](ada4945-1/figures/ada4945-1-eq09.png)

$$\frac{-D_{IN}}{R_{G}} = - \frac{V_{+OUT}}{R_{F}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Subtracting the previous equations gives the relationship that shows $R_{F}$ and $R_{G}$ setting the differential gain.

![Equation as printed (p. 43)](ada4945-1/figures/ada4945-1-eq10.png)

$$( V_{+ OUT} - V_{-OUT} ) = ( + D_{IN} - ( - D_{IN} ) ) \times \frac{R_{F}}{R_{G}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The common-mode feedback loop drives the output common mode voltage that is sampled at the midpoint of the output voltage divider to equal the voltage at $V_{OCM}$. This voltage equalization results in the following relationships:

![Equation as printed (p. 44)](ada4945-1/figures/ada4945-1-eq11.png)

$$V_{+OUT} = V_{OCM} + \frac{V_{OUT,dm}}{2}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 44)](ada4945-1/figures/ada4945-1-eq12.png)

$$V_{-OUT} = V_{OCM} - \frac{V_{OUT , dm}}{2}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Note that the summing junction input voltages of the differential amplifier (+IN and −IN in Figure 99) are set by both the output voltages and the input voltages.

![Equation as printed (p. 44)](ada4945-1/figures/ada4945-1-eq13.png)

$$V_{+IN} = +D_{IN}\left(\frac{R_{F}}{R_{F} + R_{G}}\right) + V_{-OUT}\left(\frac{R_{G}}{R_{F} + R_{G}}\right)$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 44)](ada4945-1/figures/ada4945-1-eq14.png)

$$V_{-IN} = -D_{IN}\left(\frac{R_F}{R_F+R_G}\right) + V_{+OUT}\left(\frac{R_G}{R_F+R_G}\right)$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

#### Output Voltage Clamp
<!-- pages: 44-45 -->

In addition to the differential and common-mode signal paths, the ADA4945-1 implements clamping circuits to protect the input devices of circuits being driven by the ADA4945-1, hereafter assumed to be an ADC, from being overdriven and potentially damaged. These clamping circuits use both differential and common-mode feedback to limit the output voltages to a range defined by the voltage applied to two reference pins, +$V_{CLAMP}$ and −$V_{CLAMP}$. These high impedance pins are typically connected to potentials that define the allowable input range of the ADC, which are the ADC reference voltages (+$V_{REF}$ and −$V_{REF}$) for most ADCs.

As shown in Figure 100, the common-mode clamping circuit senses the output voltage midpoint and applies a common mode feedback signal to prevent $V_{OUT}$, cm from exceeding +$V_{CLAMP}$ or going below −$V_{CLAMP}$.

![Figure 100. Common-Mode Clamp Block Diagram](ada4945-1/figures/ada4945-1-f089.png)

*Figure 100. Common-Mode Clamp Block Diagram*

The differential clamping circuit, shown in Figure 101, senses each output (+OUT and −OUT) and applies a differential feedback signal to prevent either output from exceeding (+$V_{CLAMP}$ + 0.5 V) or going below (−$V_{CLAMP}$ − 0.5 V). The approximately 500 mV offset voltage is designed to allow the outputs to fully use the input range of the ADC without any clamp engagement, while providing input protection prior to the turn on of the ADC input protection diodes. This feature allows the ADA4945-1 to provide a full-scale signal to the ADC without incurring any clamp induced distortion, thus maximizing signal-to-noise ratio (SNR) and linearity while protecting the ADC inputs.

![Figure 101. Differential Clamp Block Diagram](ada4945-1/figures/ada4945-1-f090.png)

*Figure 101. Differential Clamp Block Diagram*

By applying a differential feedback signal in response to one or both outputs exceeding the clamp reference voltages, both outputs are limited equally, even if only one output exceeds one of the clamp reference voltages. This feature allows the ADA4945- 1 to maintain a constant output common-mode voltage even while clamping the differential outputs, which enables a faster system recovery from a clamped condition.

In systems where output clamping is not desired, the upper output clamp can be disabled by connecting +$V_{CLAMP}$ to +$V_{S}$, and the lower output clamp can be disabled by connecting −$V_{CLAMP}$ to −$V_{S}$. If one clamp is disabled (for example, −$V_{S}$ = −$V_{CLAMP}$ = 0 V), the other can be remain active, and the output is limited when either or both outputs reaches the active clamp reference.

An additional feature of the ADA4945-1 is the use of a resistor divider between the +$V_{CLAMP}$ and −$V_{CLAMP}$ pins, as shown in Figure 99, to set the default potential on the $V_{OCM}$ pin when the pin is not externally driven. Because the +$V_{CLAMP}$ and −$V_{CLAMP}$ pins are typically set to the maximum and minimum desired input voltage of the ADC (for example, +$V_{REF}$ and −$V_{REF}$), respectively, this resistor divider sets the output common-mode voltage of the ADA4945-1 at the midpoint of the ADC input range by default. By contrast, most fully-differential amplifiers use a resistor divider between the amplifier supply voltages to set the default output common-mode voltage, which may not be optimal for maximizing ADC input range usage.

#### Power Modes
<!-- page: 45 -->

The ADA4945-1 implements two fully characterized active power modes (full power, low power) and a disable mode to optimize system power and performance trade-offs. The transition time from disable mode to either of the active power modes is fast (<2µs), allowing additional power savings by dynamically placing the ADA4945-1 in disable mode when the output voltage is not needed (for example, between ADC samples in low data rate systems).

### APPLICATIONS INFORMATION
<!-- pages: 46-55 -->

#### Analyzing an Application Circuit
<!-- page: 46 -->

The ADA4945-1 uses open-loop gain and negative feedback to force the differential and common-mode output voltages to minimize the differential and common-mode error voltages. The differential error voltage is the voltage between the differential inputs labeled +IN and −IN (see Figure 98). For most purposes, this voltage is 0 V. Similarly, the difference between the actual output common-mode voltage and the voltage applied to $V_{OCM}$ is also 0 V. Starting from these two assumptions, any application circuit can be analyzed.

#### Setting the Closed-Loop Gain
<!-- page: 46 -->

Determine the differential mode gain of the circuit in Figure 98 by using the following equation:

![Equation as printed (p. 46)](ada4945-1/figures/ada4945-1-eq16.png)

$$\left| \frac{V_{OUT , dm}}{V_{IN , dm}} \right| = \frac{R_{F}}{R_{G}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

This calculation assumes that the input resistors ($R_{G}$) and feedback resistors ($R_{F}$) on each side are equal.

#### Estimating the Output Noise Voltage
<!-- pages: 46-47 -->

The differential output noise of the ADA4945-1 can be estimated by using the noise model in Figure 102. The input-referred noise voltage density, $v_{nIN}$, is modeled as a differential input, and the noise currents, $i_{nIN-}$ and $i_{nIN+}$, appear between each input and ground. The noise currents are assumed equal and produce a voltage across the parallel combination of the gain and feedback resistances. $v_{nCM}$ is the noise voltage density at the $V_{OCM}$ pin. Each of the four resistors contributes $(4kTR_{x})^{1/2}$. Table 13 summarizes the input noise sources, the multiplication factors, and the output referred noise density terms. For more noise calculation information, go to the Analog Devices Differential Amplifier Calculator ([DiffAmpCalc™](https://www.analog.com/en/resources/interactive-design-tools/adi-diffampcalc.html)), click ADIDiffAmpCalculator.zip, and follow the on-screen prompts.

![Figure 102. ADA4945-1 Noise Model](ada4945-1/figures/ada4945-1-f091.png)

*Figure 102. ADA4945-1 Noise Model*

As with conventional op amps, the output noise voltage densities can be estimated by multiplying the input referred terms at +IN and −IN by the appropriate output factor, where:

![Equation as printed (p. 46)](ada4945-1/figures/ada4945-1-eq17.png)

$$G_{N} = \frac{2}{( \beta_{1} + \beta_{2} )} \text{is the circuit noise gain.}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 46)](ada4945-1/figures/ada4945-1-eq18.png)

$$\beta_{1} = \frac{R_{G 1}}{R_{F 1} + R_{G 1}} \text{ and } \beta_{2} = \frac{R_{G 2}}{R_{F 2} + R_{G 2}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

are the feedback factors. When $R_{F1}$/$R_{G1}$ = $R_{F2}$/$R_{G2}$, then β1 = β2 = β, and the noise gain becomes

![Equation as printed (p. 46)](ada4945-1/figures/ada4945-1-eq19.png)

$$G_{N} = \frac{1}{\beta} = 1 + \frac{R_{F}}{R_{G}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Note that the output noise from $V_{OCM}$ goes to zero in this case. The total differential output noise density, $v_{nOD}$, is the root-sum square of the individual output noise terms

![Equation as printed (p. 47)](ada4945-1/figures/ada4945-1-eq20.png)

$$v_{nOD} = \sqrt{\sum_{i = 1}^{8} v^{2}_{nOi}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

**Table 13.Output Noise Voltage Density Calculations** ([table-13-p47-data.csv](ada4945-1/tables/table-13-p47-data.csv), p. 47)

| Input Noise Contribution | Input Noise Term | Input Noise Voltage Density | Output Multiplication Factor | Output-Referred Noise Voltage Density Term |
|---|---|---|---|---|
| Differential Input | $v_{nIN}$ | $v_{nIN}$ | $G_{N}$ | $v_{nO1}$ = $G_{N}$ ($v_{nIN}$) |
| Inverting Input | $i_{nIN-}$ | $i_{nIN-}$ × ($R_{G2}$\|\|$R_{F2}$) | $G_{N}$ | $v_{nO2}$ = $G_{N}$ [$i_{nIN-}$ × ($R_{G2}$\|\|$R_{F2}$)] |
| Noninverting Input | $i_{nIN+}$ | $i_{nIN+}$ × ($R_{G1}$\|\|$R_{F1}$) | $G_{N}$ | $v_{nO3}$ = GN [$i_{nIN+}$ × ($R_{G1}$\|\|$R_{F1}$)] |
| $V_{OCM}$ Input | $v_{nCM}$ | $v_{nCM}$ | $G_{N}$ ($\beta_{1}$ − $\beta_{2}$) | $v_{nO4}$ = $G_{N}$ ($\beta_{1}$ − $\beta_{2}$)($v_{nCM}$) |
| Gain Resistor, $R_{G1}$ | $v_{nRG1}$ | $(4kTR_{G1})^{1/2}$ | $G_{N}$ (1 − $\beta_{2}$) | $v_{nO5}$ = $G_{N}$ (1 − $\beta_{2}$)$(4kTR_{G1})^{1/2}$ |
| Gain Resistor, $R_{G2}$ | $v_{nRG2}$ | $(4kTR_{G2})^{1/2}$ | $G_{N}$ (1 − $\beta_{1}$) | $v_{nO6}$ = $G_{N}$ (1 − $\beta_{1}$)$(4kTR_{G2})^{1/2}$ |
| Feedback Resistor, $R_{F1}$ | $v_{nRF1}$ | $(4kTR_{F1})^{1/2}$ | 1 | $v_{nO7}$ = $(4kTR_{F1})^{1/2}$ |
| Feedback Resistor, $R_{F2}$ | $v_{nRF2}$ | $(4kTR_{F2})^{1/2}$ | 1 | $v_{nO8}$ = $(4kTR_{F2})^{1/2}$ |

#### Impact of Mismatches in the Feedback Networks
<!-- page: 47 -->

Even if the external feedback networks ($R_{F}$/$R_{G}$) are mismatched, the internal common-mode feedback loop still forces the outputs to remain balanced. The amplitudes of the signals at each output remain equal and 180° out of phase. The input-to-output, differential mode gain varies proportionately to the feedback mismatch, but the output balance is unaffected.

As well as causing a noise contribution from $V_{OCM}$, ratio matching errors in the external resistors result in a degradation of the ability of the circuit to reject input common-mode signals, similar to a four resistors difference amplifier made from a conventional op amp.

In addition, if the dc levels of the input and output common mode voltages are different, matching errors result in a small differential mode, output offset voltage. When G = 1, with a ground referenced input signal and the output common-mode level set to 2.5 V, an output offset of as much as 25 mV (1% of the difference in common-mode levels) can result if 1% tolerance resistors are used. Resistors of 1% tolerance result in a worst case input CMRR of about 40 dB, a worst case differential mode output offset of 25 mV due to the 2.5 V level shift, and no significant degradation in output balance error.

#### Calculating the Input Impedance of an Application Circuit
<!-- pages: 47-48 -->

The effective input impedance depends on whether the signal source is single-ended or differential. For a balanced differential input signal, as shown in Figure 103, the input impedance ($R_{IN, dm}$) between the inputs (+$D_{IN}$ and −$D_{IN}$) is $R_{IN, dm}$ = 2 × $R_{G}$.

![Figure 103. ADA4945-1 Configured for Balanced (Differential) Inputs](ada4945-1/figures/ada4945-1-f092.png)

*Figure 103. ADA4945-1 Configured for Balanced (Differential) Inputs*

For an unbalanced single-ended input signal, as shown in Figure 104, the input impedance is

![Equation as printed (p. 48)](ada4945-1/figures/ada4945-1-eq21.png)

$$R_{IN , SE} = R_{GI} \frac{\beta 1 + \beta 2}{\beta 1 ( \beta 2 + 1 )}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

where:

![Equation as printed (p. 48)](ada4945-1/figures/ada4945-1-eq22.png)

$$\beta 1 = \frac{R_{G 1}}{R_{G 1} + R_{F 1}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Equation as printed (p. 48)](ada4945-1/figures/ada4945-1-eq23.png)

$$\beta 2 = \frac{R_{G 2}}{R_{G 2} + R_{F 2}}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Figure 104. ADA4945-1 with Unbalanced (Single-Ended) Input](ada4945-1/figures/ada4945-1-f093.png)

*Figure 104. ADA4945-1 with Unbalanced (Single-Ended) Input*

For a balanced system where $R_{G1}$ = $R_{G2}$ = $R_{G}$ and $R_{F1}$ = $R_{F2}$ = $R_{F}$, the equations simplify to

![Equation as printed (p. 48)](ada4945-1/figures/ada4945-1-eq24.png)

$$\beta 1 = \beta 2 = \frac{R_{G}}{R_{G} + R_{F}} \, \text{and} \, R_{\text{IN,SE}} = \left( \frac{R_{G}}{1 - \frac{R_{F}}{2 ( R_{G} + R_{F} )}} \right)$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

The input impedance of the circuit is effectively higher than it would be for a conventional op amp connected as an inverter because a fraction of the differential output voltage appears at the inputs as a common-mode signal, partially bootstrapping the voltage across the $R_{G1}$ input resistor.

#### Terminating a Single-Ended Input
<!-- pages: 48-50 -->

This section describes how to properly terminate a single-ended input to the ADA4945-1. Assume a system gain of 1 where $R_{F1}$ = $R_{F2}$ = $R_{G1}$ = $R_{G2}$ = 499 Ω, an input source with an open-circuit output voltage of 2 $V_{p-p}$, and a source resistance of 50 Ω. Figure 105 shows the circuit.

1. Calculate the input impedance.

![Equation as printed (p. 48)](ada4945-1/figures/ada4945-1-eq25.png)

$$\beta 1 = \beta 2 = 499 / 998 = 0.5 \text{and} R_{\text{IN}} = 665.33 \ \Omega$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Figure 105. Single-Ended Input Impedance RIN](ada4945-1/figures/ada4945-1-f094.png)

*Figure 105. Single-Ended Input Impedance $R_{IN}$*

2. Add a termination resistor ($R_{T}$) to match the 50 Ω source resistance. Because $R_{T}$||665.33 Ω = 50 Ω, $R_{T}$ = 54.06 Ω.

![Figure 106. Adding Termination Resistor, RT](ada4945-1/figures/ada4945-1-f095.png)

*Figure 106. Adding Termination Resistor, RT*

3. Replace the source termination resistor combination with the Thevenin equivalent. The Thevenin equivalent of the source resistance, $R_{S}$, and the termination resistance, $R_{T}$, is $R_{TH}$ = $R_{S}$||$R_{T}$ = 25.976 Ω. The Thevenin equivalent of the source voltage is

![Equation as printed (p. 49)](ada4945-1/figures/ada4945-1-eq26.png)

$$V_{TH} = V_{S} \frac{R_{T}}{R_{S} + R_{S}} = 1.039 \, V_{p - p}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Figure 107. Thevenin Equivalent Circuit](ada4945-1/figures/ada4945-1-f096.png)

*Figure 107. Thevenin Equivalent Circuit*

4. Set $R_{F1}$ = $R_{F2}$ = $R_{F}$ to maintain a balanced system. Compensate the imbalance caused by $R_{TH}$. There are two methods available to compensate, as follows:
   - Add $R_{TH}$ to $R_{G2}$ to maintain balanced gain resistances and increase $R_{F1}$ and $R_{F2}$ to $R_F = \frac{V_S}{V_{TH}}$ Gain($R_{G}$ + $R_{TH}$) to maintain the system gain.
   - Decrease $R_{G2}$ to $R_{G2} = \frac{R_F \times V_{TH}}{V_S \times \text{Gain}}$ to maintain system gain and decrease $R_{G1}$ to ($R_{G2}$ − $R_{TH}$) to maintain balanced gain resistances.

The first compensation method is used in the Analog Devices [DiffAmpCalc™](https://www.analog.com/en/resources/interactive-design-tools/adi-diffampcalc.html) tool. Using the second compensation method, $R_{G2}$ =259.241 Ω and $R_{G1}$ = 259.241 − 25.976 = 233.265 Ω. The modified circuit is shown in Figure 108

![Figure 108. Thevenin Equivalent with Matched Gain Resistors](ada4945-1/figures/ada4945-1-f097.png)

*Figure 108. Thevenin Equivalent with Matched Gain Resistors*

Figure 108 shows an easily manageable circuit with matched feedback loops that can be easily evaluated.

5. The modified gain resistor, $R_{G1}$, changes the input impedance. Repeat Step 1 through Step 4 several times using the modified value of $R_{G1}$ from the previous iteration until the value of $R_{T}$ does not change from the previous iteration. After three additional iterations, the change in $R_{G1}$ is less than 0.1%. The final circuit is shown in Figure 109 with the closest 1% resistor values.

![Figure 109. Terminated Single-Ended-to-Differential System with G =1](ada4945-1/figures/ada4945-1-f098.png)

*Figure 109. Terminated Single-Ended-to-Differential System with G =1*

#### Input Common-Mode Voltage Range
<!-- page: 50 -->

The input common-mode range at the summing nodes of the ADA4945-1 is specified as −$V_{S}$ to +$V_{S}$ − 1.3 V. By extending the input common-mode range down to −$V_{S}$, the ADA4945-1 is especially well suited to dc-coupled, single-ended-to-differential, and single-supply applications, such as ADC driving.

#### Input and Output Capacitive AC Coupling
<!-- page: 50 -->

Although the ADA4945-1 is best suited to dc-coupled applications, it is possible to use the device in ac-coupled circuits. Input ac coupling capacitors can be inserted between the source and $R_{G}$. This ac coupling blocks the flow of the dc common-mode feedback current and causes the ADA4945-1 dc input common-mode voltage to equal the dc output common-mode voltage. These ac coupling capacitors must be placed in both loops to keep the feedback factors matched. Output ac coupling capacitors can be placed in series between each output and the respective load of each output.

#### Setting the Output Common-Mode Voltage
<!-- pages: 50-51 -->

The $V_{OCM}$ pin of the ADA4945-1 is internally biased at a voltage approximately equal to the midway between the output voltage clamps, ((+$V_{CLAMP}$) + (−$V_{CLAMP}$))/2. Relying on this internal bias results in an output common-mode voltage that is within approximately 100 mV of the expected value.

When more accurate control of the output common-mode level is required, it is recommended that an external source, or resistor divider (10 kΩ or greater resistors), be used. The output common-mode offset listed in Table 2, Table 5, and Table 8 assumes that the $V_{OCM}$ input is driven by a low impedance voltage source.

It is also possible to connect the $V_{OCM}$ input to a common-mode level (CML) output of an ADC. However, care must be taken to ensure that the output has sufficient drive capability. The input impedance of the $V_{OCM}$ pin is approximately 125 kΩ.

#### Disable Pin
<!-- page: 51 -->

The ADA4945-1 features a D̅I̅S̅A̅B̅L̅E̅ pin that can be used to minimize the quiescent current consumed when the device is not being used. D̅I̅S̅A̅B̅L̅E̅ is asserted by applying a low logic level to the D̅I̅S̅A̅B̅L̅E̅ pin. The logic level for the D̅I̅S̅A̅B̅L̅E̅ pin is referenced to $D_{GND}$. See Table 3, Table 6, and Table 9 for the threshold limits.

The D̅I̅S̅A̅B̅L̅E̅ pin features an internal pull-up network that enables the amplifier for normal operation. The ADA4945-1 D̅I̅S̅A̅B̅L̅E̅ pin can be left floating (that is, no external connection is required) and does not require an external pullup resistor to ensure normal on operation (see Figure 110). When the ADA4945-1 is disabled, the output is high impedance. Note that the outputs are tied to the inputs through the feedback resistors and to the source using the gain resistors. In addition, there are back to back diodes on the input pins that limit the differential voltage to 1.2 V.

![Figure 110. DISABLE Pin Circuit](ada4945-1/figures/ada4945-1-f099.png)

*Figure 110. D̅I̅S̅A̅B̅L̅E̅ Pin Circuit*

#### Driving a Capacitive Load
<!-- pages: 51-52 -->

A purely capacitive load reacts with the bond wire and pin inductance of the ADA4945-1, resulting in high frequency ringing in the transient response and loss of phase margin. One way to minimize this effect is to place a resistor in series with each output to buffer the load capacitance. The resistor and load capacitance form a first-order, low-pass filter. Therefore, the resistor value must be as small as possible. In some cases, the ADCs require small series resistors to be added on their inputs.

Figure 111 shows the capacitive load vs. the series resistance required to maintain a minimum 45° of phase margin. The test circuit is shown in Figure 112.

![Figure 111. Series Resistance vs. Load Capacitance](ada4945-1/figures/ada4945-1-f119.png)

*Figure 111. Series Resistance vs. Load Capacitance*

Digitized data: [series-resistance-vs-load-capacitance.csv](ada4945-1/curves/series-resistance-vs-load-capacitance.csv) (x: pF; y: Ω) — values read off the printed plot by the digitizer, not published data.

![Figure 112. Series Resistance with a Capacitive Load Test Circuit](ada4945-1/figures/ada4945-1-f120.png)

*Figure 112. Series Resistance with a Capacitive Load Test Circuit*

#### Output Clamps
<!-- pages: 52-53 -->

The ADA4945-1 implements output voltage clamps to effectively limit the differential and common-mode signal levels, thereby protecting circuitry following the ADA4945-1 from being overdriven. The operation of these clamps is discussed in the Theory of Operation section. Figure 113 shows an example where the output voltage clamp may be used while driving an ADC. In this example, the ADA4945-1 is operating from +7 V and −2 V supplies, and the ADC is using +5 V reference. In such a scenario, the ADC input can potentially be overdriven if no clamping were present. By connecting the clamps to the positive and negative references of the ADC, the differential and common-mode signal levels are limited as shown in Figure 114 and Figure 115. Note that the differential signals are clamped ~500 mV beyond the clamp set voltage to allow full swing to the references. The common-mode signal is clamped right at the clamp set voltages.

![Figure 113. ADA4945-1 Output Voltage Clamp Usage](ada4945-1/figures/ada4945-1-f100.png)

*Figure 113. ADA4945-1 Output Voltage Clamp Usage*

![Figure 114. Clamped Differential Signal Levels](ada4945-1/figures/ada4945-1-f121.png)

*Figure 114. Clamped Differential Signal Levels*

Digitized data: [clamped-differential-signal-levels.csv](ada4945-1/curves/clamped-differential-signal-levels.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 115. Clamped Common-Mode Signal Levels](ada4945-1/figures/ada4945-1-f122.png)

*Figure 115. Clamped Common-Mode Signal Levels*

Digitized data: [clamped-common-mode-signal-levels.csv](ada4945-1/curves/clamped-common-mode-signal-levels.csv) (x: µs; y: V) — values read off the printed plot by the digitizer, not published data.

#### Driving a High Precision ADC
<!-- pages: 53-55 -->

The ADA4945-1 is ideally suited for broadband dc-coupled applications. The recommended list of precision converters is shown in Table 15. The circuit in Figure 116 shows an example of the ADA4945-1 driving a precision ADC such as the AD4003 (an 18-bit, 2 MSPS, successive approximation ADC), or the AD7768 (a 24-bit, 256 kSPS, sigma-delta ADC). The ADA4945-1 is dc-coupled on the input and the output, which eliminates the need for a transformer to drive the ADC. In this example, the ADA4945-1 is applied in a differential input to differential output configuration, with a gain of 1, and with dual supplies of +7 V and −2 V. The output of the ADA4945-1 is level shifted to match the input common mode of the ADC. The gain is set by the ratio of the feedback resistor to the gain resistor. In addition, the circuit can be used in a single-ended input to differential output configuration. If needed, a termination resistor in parallel with the source input can be used. When a single-ended input is used, the input impedance of the amplifier can be calculated as shown in the Terminating a Single-Ended Input section. If the feedback and gain resistors are all 1 kΩ, as in Figure 116, the single-ended input impedance is approximately 1.33 kΩ, which, in parallel with a 52.3 Ω termination resistor, provides a 50 Ω termination for the source. An additional 25.5 Ω (1025.5 Ω total) at the inverting input balances the parallel impedance of the 50 Ω source and the termination resistor driving the noninverting input. However, if a differential source input is used, the differential input impedance is 2 kΩ. In this case, two 52.3 Ω termination resistors are used to terminate the inputs.

When driving the AD7768 in this example, the ADA4945-1 is driven by a signal generator having an 8 $V_{p-p}$ symmetric, bipolar output. The $V_{OCM}$ input of the ADA4945-1 is bypassed for noise reduction and is driven via the common-mode source of the AD7768 to 2.5 V. With an output common-mode voltage of 2.5 V, each ADA4945-1 output swings between 0.5 V and 4.5 V, opposite in phase, providing a gain of 1 and a 8 V p-p differential signal to the ADC input. The differential RC section between the ADA4945-1 output and the ADC input provides a single-pole, low-pass filter to help reduce current spikes due to ADC input switching.

Table 14 shows the SNR and total distortion (THD) of the ADA4945-1 driving the AD7768 and AD4003 for various input frequencies at a near full-scale signal. The RC filter values in Figure 116 are also shown, as well as the reference voltage (REF) level.

![Figure 116. ADA4945-1 Driving Precision ADC](ada4945-1/figures/ada4945-1-f103.png)

*Figure 116. ADA4945-1 Driving Precision ADC*

**Table 14.SNR and THD for ADA4945-1 Driving AD7768 and AD4003** ([table-14-p54-data.csv](ada4945-1/tables/table-14-p54-data.csv), p. 54)

| ADC | Frequency (kHz) | Signal Level (V p-p) | REF (V) | R (Ω) | C (pF) | $C_{DIFF}$ (pF) | SNR (dB) | THD (dB) |
|---|---|---|---|---|---|---|---|---|
| [AD7768](https://www.analog.com/AD7768?doc=ADA4945-1.pdf) | 1 | 8.0 | 4.096 | 10 | 270 | 680 | 106.7 | −115.9 |
| [AD7768](https://www.analog.com/AD7768?doc=ADA4945-1.pdf) | 2 | 8.0 | 4.096 | 10 | 270 | 680 | 106.5 | −115.5 |
| [AD7768](https://www.analog.com/AD7768?doc=ADA4945-1.pdf) | 10 | 8.0 | 4.096 | 10 | 270 | 680 | 105.8 | −116.9 |
| [AD7768](https://www.analog.com/AD7768?doc=ADA4945-1.pdf) | 20 | 7.98 | 4.096 | 10 | 270 | 680 | 104.7 | −116.2 |
| [AD4003](https://www.analog.com/AD4003?doc=ADA4945-1.pdf) | 1 | 9.5 | 5.0 | 200 | 180 | Not applicable | 98.5 | −123.5 |
| [AD4003](https://www.analog.com/AD4003?doc=ADA4945-1.pdf) | 10 | 9.5 | 5.0 | 200 | 180 | Not applicable | 98.3 | −117.0 |
| [AD4003](https://www.analog.com/AD4003?doc=ADA4945-1.pdf) | 100 | 9.1 | 5.0 | 200 | 180 | Not applicable | 96.3 | −100.3 |

**Table 15. Recommended Converters** ([table-15-p55-data.csv](ada4945-1/tables/table-15-p55-data.csv), p. 55)

| Product | Power (mW) | Throughput (MSPS) | Resolution (Bits) | SNR (dB) |
|---|---|---|---|---|
| [AD4001](http://www.analog.com/AD4001?doc=ADA4945-1.pdf) | 16 | 2 | 16 | 96 |
| [AD4003](http://www.analog.com/AD4003?doc=ADA4945-1.pdf) | 16 | 2 | 18 | 100 |
| [AD4005](http://www.analog.com/AD4005?doc=ADA4945-1.pdf) | 8 | 1 | 16 | 96 |
| [AD4007](http://www.analog.com/AD4007?doc=ADA4945-1.pdf) | 8 | 1 | 18 | 100 |
| [AD4011](http://www.analog.com/AD4011?doc=ADA4945-1.pdf) | 4 | 0.5 | 18 | 100 |
| [AD4020](http://www.analog.com/AD4020?doc=ADA4945-1.pdf) | 20 | 2 | 20 | 100 |

### LAYOUT, GROUNDING, AND BYPASSING
<!-- page: 55 -->

As a high speed device, the ADA4945-1 is sensitive to the PCB environment in which it operates. Using the superior performance of the ADA4945-1 requires attention to the details of high speed PCB design.

Ensure that signal routing is short and direct to avoid parasitic effects. Wherever complementary signals exist, provide a symmetrical layout to maximize balanced performance. When routing differential signals over a long distance, ensure that PCB traces are close together, and twist any differential wiring such that loop area is minimized. This configuration reduces radiated energy and makes the circuit less susceptible to interference.

Bypass the power supply pins as near to the device as possible and directly to a nearby ground plane. Use high frequency ceramic chip capacitors. Use two parallel bypass capacitors (0.1 µF and 10 µF) for each supply. Place the 0.1 µF capacitor as near to the device as possible. Further away, provide low frequency bypassing using 10 µF tantalum capacitors from each supply to ground.

The ground plane must be as continuous and unbroken as possible to provide a low impedance path for return currents to the supply. As such, the ground plane should be kept free of any signal traces or other interruptions.

### OUTLINE DIMENSIONS
<!-- page: 56 -->

![Figure 117. 16-Lead Lead Frame Chip Scale Package (LFCSP) 3 mm x 3mm Body and 0.75 mm Package Height (CP-16-22)](ada4945-1/figures/ada4945-1-f104.png)

*Figure 117. 16-Lead Lead Frame Chip Scale Package (LFCSP) 3 mm x 3mm Body and 0.75 mm Package Height (CP-16-22)*

*Dimensions shown in millimeters*

### ORDERING GUIDE
<!-- page: 56 -->

**Table 16. Ordering Guide** ([table-16-p56-data.csv](ada4945-1/tables/table-16-p56-data.csv), p. 56)

| Model $[^1]$ | Temperature Range | Package Description | Package Option | Ordering Quantity | Marking Code |
|---|---|---|---|---|---|
| ADA4945-1ACPZ-R2 | −40°C to +125°C | 16-Lead LFCSP | CP-16-22 | 250 | C9D |
| ADA4945-1ACPZ-RL | −40°C to +125°C | 16-Lead LFCSP | CP-16-22 | 5,000 | C9D |
| ADA4945-1ACPZ-R7 | −40°C to +125°C | 16-Lead LFCSP | CP-16-22 | 1,500 | C9D |
| ADA4945-1CP-EBZ |  | Evaluation Board |  |  |  |
| AMC-ADA4945-1EBZ |  | ADC Mezzanine Card |  |  |  |

$[^1]$ Z = RoHS-compliant part.

ALL INFORMATION CONTAINED HEREIN IS PROVIDED “AS IS” WITHOUT REPRESENTATION OR WARRANTY. NO RESPONSIBILITY IS ASSUMED BY ANALOG DEVICES FOR ITS USE, NOR FOR ANY INFRINGEMENTS OF PATENTS OR OTHER RIGHTS OF THIRD PARTIES THAT MAY RESULT FROM ITS USE. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. NO LICENCE, EITHER EXPRESSED OR IMPLIED, IS GRANTED UNDER ANY ADI PATENT RIGHT, COPYRIGHT, MASK WORK RIGHT, OR ANY OTHER ADI INTELLECTUAL PROPERTY RIGHT RELATING TO ANY COMBINATION, MACHINE, OR PROCESS WHICH ADI PRODUCTS OR SERVICES ARE USED. TRADEMARKS AND REGISTERED TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS.
