---
type: Analog Component
title: "AD9081 — MxFE Quad, 16-Bit, 12 GSPS RF DAC and Quad, 12-Bit, 4 GSPS RF ADC"
description: "MxFE Quad, 16-Bit, 12 GSPS RF DAC and Quad, 12-Bit, 4 GSPS RF ADC"
resource: "https://www.analog.com/en/products/ad9081.html"
tags: ["datasheet", "adi"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ad9081.pdf"
    title: "AD9081 data sheet"
    author: "team:analog-devices"
    last_modified: "4/2021"
tables:
  - file: "ad9081/tables/table-00-p4-spec.csv"
    title: "Table 1."
    page: 4
  - file: "ad9081/tables/table-01-p4-spec.csv"
    title: "Table 2. Power Consumption"
    page: 4
  - file: "ad9081/tables/table-02-p5-spec.csv"
    title: "Table 3. DAC DC Specifications"
    page: 5
  - file: "ad9081/tables/table-03-p6-spec.csv"
    title: "Table 4. ADC DC Specifications"
    page: 6
  - file: "ad9081/tables/table-04-p7-spec.csv"
    title: "Table 5. Clock Inputs and Outputs"
    page: 7
  - file: "ad9081/tables/table-05-p7-spec.csv"
    title: "Table 6. Clock Input and PLL Frequency Specifications"
    page: 7
  - file: "ad9081/tables/table-06-p8-spec.csv"
    title: "Table 7. DAC Sample Rate Specifications"
    page: 8
  - file: "ad9081/tables/table-07-p9-spec.csv"
    title: "Table 8. ADC Sample Rate Specifications"
    page: 9
  - file: "ad9081/tables/table-08-p10-spec.csv"
    title: "Table 9. Input Data Rate Specifications"
    page: 10
  - file: "ad9081/tables/table-09-p11-spec.csv"
    title: "Table 10. NCO Frequency Specifications"
    page: 11
  - file: "ad9081/tables/table-10-p11-spec.csv"
    title: "Table 11. Serial Interface Rate Specifications"
    page: 11
  - file: "ad9081/tables/table-11-p11-spec.csv"
    title: "Table 12. JESD204 Receiver (JRx) Electrical Specifications"
    page: 11
  - file: "ad9081/tables/table-12-p12-spec.csv"
    title: "Table 13. JESD204 Transmitter (JTx) Electrical Specifications"
    page: 12
  - file: "ad9081/tables/table-13-p12-spec.csv"
    title: "Table 14. SYSREF Electrical Specifications"
    page: 12
  - file: "ad9081/tables/table-14-p13-spec.csv"
    title: "Table 15. CMOS Pin Specifications"
    page: 13
  - file: "ad9081/tables/table-15-p13-spec.csv"
    title: "Table 16. DAC AC Specifications"
    page: 13
  - file: "ad9081/tables/table-16-p16-spec.csv"
    title: "Table 17. ADC AC Specifications"
    page: 16
  - file: "ad9081/tables/table-17-p19-spec.csv"
    title: "Table 18. Timing Specifications"
    page: 19
  - file: "ad9081/tables/table-18-p21-abs_max.csv"
    title: "Table 19."
    page: 21
  - file: "ad9081/tables/table-19-p21-data.csv"
    title: "Table 20. Simulated Thermal Resistance[^1]"
    page: 21
  - file: "ad9081/tables/table-20-p22-pin.csv"
    title: "Table 21. Pin Function Descriptions"
    page: 22
  - file: "ad9081/tables/table-21-p45-data.csv"
    title: "Ordering Guide"
    page: 45
  - file: "ad9081/tables/table-22-p45-data.csv"
    title: "Evaluation Boards"
    page: 45
figures:
  - file: "ad9081/figures/ad9081-f001.png"
    caption: "Figure 1."
    type: "block_diagram"
    page: 3
  - file: "ad9081/figures/ad9081-f002.png"
    caption: "Figure 2. Timing Diagram for 3-Wire Write Operation"
    type: "timing_diagram"
    page: 19
  - file: "ad9081/figures/ad9081-f003.png"
    caption: "Figure 4. Timing Diagram for 4-Wire Read Operation"
    type: "timing_diagram"
    page: 20
  - file: "ad9081/figures/ad9081-f005.png"
    caption: "Figure 5. Pin Configuration"
    type: "pinout"
    page: 22
  - file: "ad9081/figures/ad9081-f006.png"
    caption: "Figure 6. HD2 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C"
    type: "characteristic_curve"
    page: 27
  - file: "ad9081/figures/ad9081-f007.png"
    caption: "Figure 7. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C"
    type: "characteristic_curve"
    page: 27
  - file: "ad9081/figures/ad9081-f008.png"
    caption: "Figure 8. HD3 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C"
    type: "characteristic_curve"
    page: 27
  - file: "ad9081/figures/ad9081-f009.png"
    caption: "Figure 9. HD2 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C"
    type: "characteristic_curve"
    page: 27
  - file: "ad9081/figures/ad9081-f010.png"
    caption: "Figure 10. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B"
    type: "characteristic_curve"
    page: 27
  - file: "ad9081/figures/ad9081-f011.png"
    caption: "Figure 11. HD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C"
    type: "characteristic_curve"
    page: 27
  - file: "ad9081/figures/ad9081-f012.png"
    caption: "Figure 12. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C"
    type: "characteristic_curve"
    page: 28
  - file: "ad9081/figures/ad9081-f013.png"
    caption: "Figure 13. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C"
    type: "characteristic_curve"
    page: 28
  - file: "ad9081/figures/ad9081-f014.png"
    caption: "Figure 14. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C"
    type: "characteristic_curve"
    page: 28
  - file: "ad9081/figures/ad9081-f015.png"
    caption: "Figure 15. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B"
    type: "characteristic_curve"
    page: 28
  - file: "ad9081/figures/ad9081-f016.png"
    caption: "Figure 16. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C"
    type: "characteristic_curve"
    page: 28
  - file: "ad9081/figures/ad9081-f017.png"
    caption: "Figure 17. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B"
    type: "characteristic_curve"
    page: 28
  - file: "ad9081/figures/ad9081-f018.png"
    caption: "Figure 18. IMD3 vs. f_{OUT} over Digital Scale (Mode 17B), 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C,"
    type: "characteristic_curve"
    page: 29
  - file: "ad9081/figures/ad9081-f019.png"
    caption: "Figure 19. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital"
    type: "characteristic_curve"
    page: 29
  - file: "ad9081/figures/ad9081-f020.png"
    caption: "Figure 20. IMD3 vs. f_{OUT} over f_{DAC} , Digital Scale -7 dBFS, IMD3 is a Two-Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital Scale"
    type: "characteristic_curve"
    page: 29
  - file: "ad9081/figures/ad9081-f021.png"
    caption: "Figure 21. IMD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital"
    type: "characteristic_curve"
    page: 29
  - file: "ad9081/figures/ad9081-f022.png"
    caption: "Figure 22. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital"
    type: "characteristic_curve"
    page: 29
  - file: "ad9081/figures/ad9081-f023.png"
    caption: "Figure 23. SFDR, Worst In-Band Spurious vs. f_{OUT} over f_{DAC} , with 0 dBFS Tone Level"
    type: "characteristic_curve"
    page: 29
  - file: "ad9081/figures/ad9081-f024.png"
    caption: "Figure 24. DAC0 Fundamental Output Power vs. f_{OUT} Across f_{DAC}, at 0 dBFS"
    type: "characteristic_curve"
    page: 30
  - file: "ad9081/figures/ad9081-f025.png"
    caption: "Figure 25. Single Sideband Phase Noise vs. Frequency Offset for Different Clock Input Power (P_{CLK} ), f_{OUT} = 1.8 GHz, External 12 GHz Clock Input with Clock PLL Disabled"
    type: "characteristic_curve"
    page: 30
  - file: "ad9081/figures/ad9081-f026.png"
    caption: "Figure 26. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , Shuffle On, 16-Bit Resolution, Mode 15C"
    type: "characteristic_curve"
    page: 30
  - file: "ad9081/figures/ad9081-f027.png"
    caption: "Figure 27. Single Sideband Phase Noise vs. Frequency Offset for Different"
    type: "characteristic_curve"
    page: 30
  - file: "ad9081/figures/ad9081-f028.png"
    caption: "Figure 28. Single Sideband Phase Noise vs. Frequency Offset for Different DAC Output Frequencies (f_{OUT} ), External 12 GHz Clock Input with Clock PLL Disabled"
    type: "characteristic_curve"
    page: 30
  - file: "ad9081/figures/ad9081-f029.png"
    caption: "Figure 29. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , 12-Bit Resolution, Shuffle On, Mode 24C"
    type: "characteristic_curve"
    page: 30
  - file: "ad9081/figures/ad9081-f030.png"
    caption: "Figure 30. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 16-Bit Resolution, Mode 15C"
    type: "characteristic_curve"
    page: 31
  - file: "ad9081/figures/ad9081-f031.png"
    caption: "Figure 31. Dual Band ACLR Performance for Two 20 MHz LTE carriers at f_{OUT}"
    type: "scope_capture"
    page: 31
  - file: "ad9081/figures/ad9081-f032.png"
    caption: "Figure 32. Dual Band Wideband Plot for Two 20 MHz LTE Carriers at f_{OUT} = 1.88 GHz and f_{OUT} = 2.145 GHz (3GPP Bands, B1 and B3, Respectively),"
    type: "scope_capture"
    page: 31
  - file: "ad9081/figures/ad9081-f033.png"
    caption: "Figure 33. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 12-Bit Resolution, Mode 24C"
    type: "characteristic_curve"
    page: 31
  - file: "ad9081/figures/ad9081-f034.png"
    caption: "Figure 34. Dual Band ACLR Performance for two 20 MHz LTE carriers at f_{OUT}"
    type: "scope_capture"
    page: 31
  - file: "ad9081/figures/ad9081-f035.png"
    caption: "Figure 35. ACLR Performance for 100 MHz 5G Test Vector at f_{OUT} = 3.9 GHz"
    type: "scope_capture"
    page: 31
  - file: "ad9081/figures/ad9081-f036.png"
    caption: "Figure 36. Single-Tone FFT at f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 32
  - file: "ad9081/figures/ad9081-f037.png"
    caption: "Figure 37. Single-Tone FFT at f_{IN} = 900 MHz"
    type: "characteristic_curve"
    page: 32
  - file: "ad9081/figures/ad9081-f038.png"
    caption: "Figure 38. Single-Tone FFT at f_{IN} = 1800 MHz"
    type: "characteristic_curve"
    page: 32
  - file: "ad9081/figures/ad9081-f039.png"
    caption: "Figure 39. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 32
  - file: "ad9081/figures/ad9081-f040.png"
    caption: "Figure 40. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz"
    type: "characteristic_curve"
    page: 32
  - file: "ad9081/figures/ad9081-f041.png"
    caption: "Figure 41. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz"
    type: "characteristic_curve"
    page: 32
  - file: "ad9081/figures/ad9081-f042.png"
    caption: "Figure 42. Single-Tone FFT at f_{IN} = 2700 MHz"
    type: "characteristic_curve"
    page: 33
  - file: "ad9081/figures/ad9081-f043.png"
    caption: "Figure 43. Single-Tone FFT at f_{IN} = 3600 MHz"
    type: "characteristic_curve"
    page: 33
  - file: "ad9081/figures/ad9081-f044.png"
    caption: "Figure 44. Single-Tone FFT at f_{IN} = 4500 MHz"
    type: "characteristic_curve"
    page: 33
  - file: "ad9081/figures/ad9081-f045.png"
    caption: "Figure 45. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz"
    type: "characteristic_curve"
    page: 33
  - file: "ad9081/figures/ad9081-f046.png"
    caption: "Figure 46. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz"
    type: "characteristic_curve"
    page: 33
  - file: "ad9081/figures/ad9081-f047.png"
    caption: "Figure 47. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz"
    type: "characteristic_curve"
    page: 33
  - file: "ad9081/figures/ad9081-f048.png"
    caption: "Figure 48. Single-Tone FFT at f_{IN} = 5400 MHz"
    type: "characteristic_curve"
    page: 34
  - file: "ad9081/figures/ad9081-f049.png"
    caption: "Figure 49. Single-Tone FFT at f_{IN} = 6300 MHz"
    type: "characteristic_curve"
    page: 34
  - file: "ad9081/figures/ad9081-f050.png"
    caption: "Figure 50. Single-Tone FFT at f_{IN} = 7200 MHz"
    type: "characteristic_curve"
    page: 34
  - file: "ad9081/figures/ad9081-f051.png"
    caption: "Figure 51. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz"
    type: "characteristic_curve"
    page: 34
  - file: "ad9081/figures/ad9081-f052.png"
    caption: "Figure 52. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz"
    type: "characteristic_curve"
    page: 34
  - file: "ad9081/figures/ad9081-f053.png"
    caption: "Figure 53. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz"
    type: "characteristic_curve"
    page: 34
  - file: "ad9081/figures/ad9081-f054.png"
    caption: "Figure 54. Two-Tone FFT, f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz, A_{IN1} and A_{IN2} = -7 dBFS (IMD3L = 2f_{IN1} - f_{IN2} , and IMD3H = 2f_{IN2} - f_{IN1} )"
    type: "characteristic_curve"
    page: 35
  - file: "ad9081/figures/ad9081-f055.png"
    caption: "Figure 55. Two-Tone FFT, f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 35
  - file: "ad9081/figures/ad9081-f056.png"
    caption: "Figure 56. Two-Tone FFT, f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 35
  - file: "ad9081/figures/ad9081-f057.png"
    caption: "Figure 57. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz"
    type: "characteristic_curve"
    page: 35
  - file: "ad9081/figures/ad9081-f058.png"
    caption: "Figure 58. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz"
    type: "characteristic_curve"
    page: 35
  - file: "ad9081/figures/ad9081-f059.png"
    caption: "Figure 59. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz"
    type: "characteristic_curve"
    page: 35
  - file: "ad9081/figures/ad9081-f060.png"
    caption: "Figure 60. Two-Tone FFT, f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 36
  - file: "ad9081/figures/ad9081-f061.png"
    caption: "Figure 61. SNR and SFDR vs. Input Frequency with A_{IN} =-1 dBFS"
    type: "characteristic_curve"
    page: 36
  - file: "ad9081/figures/ad9081-f062.png"
    caption: "Figure 62. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS"
    type: "characteristic_curve"
    page: 36
  - file: "ad9081/figures/ad9081-f063.png"
    caption: "Figure 63. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz"
    type: "characteristic_curve"
    page: 36
  - file: "ad9081/figures/ad9081-f064.png"
    caption: "Figure 64. SNR vs. Input Frequency, Direct Clock vs. On-Chip PLL Clock,  f_{S}  = 4 GHz, A_{IN} = -1 dBFS"
    type: "characteristic_curve"
    page: 36
  - file: "ad9081/figures/ad9081-f065.png"
    caption: "Figure 65. FFT Close-In Comparison, Direct Clock vs. On-Chip PLL Clock,  f_{S} = 4 GHz, f_{IN} = 2.7 GHz, A_{IN} = -1 dBFS"
    type: "characteristic_curve"
    page: 36
  - file: "ad9081/figures/ad9081-f066.png"
    caption: "Figure 66. SNR and SFDR vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS"
    type: "characteristic_curve"
    page: 37
  - file: "ad9081/figures/ad9081-f067.png"
    caption: "Figure 67. SNR and SFDR vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 37
  - file: "ad9081/figures/ad9081-f068.png"
    caption: "Figure 68. Power vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS"
    type: "characteristic_curve"
    page: 37
  - file: "ad9081/figures/ad9081-f069.png"
    caption: "Figure 69. Harmonics (HD2, HD3, and Interleaving) vs. Die Temperature, f_{IN} = 1.85 GHz"
    type: "characteristic_curve"
    page: 37
  - file: "ad9081/figures/ad9081-f070.png"
    caption: "Figure 70. Harmonics (HD2 and HD3) vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 37
  - file: "ad9081/figures/ad9081-f071.png"
    caption: "Figure 71. Power vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 37
  - file: "ad9081/figures/ad9081-f072.png"
    caption: "Figure 72. Input Referred Noise Histogram"
    type: "characteristic_curve"
    page: 38
  - file: "ad9081/figures/ad9081-f073.png"
    caption: "Figure 73. DNL, f_{IN} = 255 MHz"
    type: "characteristic_curve"
    page: 38
  - file: "ad9081/figures/ad9081-f074.png"
    caption: "Figure 74. Measured Input Bandwidth ADC Input on AD9081-FMCA-EBZ (No Matching Network)"
    type: "characteristic_curve"
    page: 38
  - file: "ad9081/figures/ad9081-f075.png"
    caption: "Figure 75. INL, f_{IN} = 255 MHz"
    type: "characteristic_curve"
    page: 38
  - file: "ad9081/figures/ad9081-f076.png"
    caption: "Figure 76. Single-Tone FFT at f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 39
  - file: "ad9081/figures/ad9081-f077.png"
    caption: "Figure 77. Single-Tone FFT at f_{IN} = 900 MHz"
    type: "characteristic_curve"
    page: 39
  - file: "ad9081/figures/ad9081-f078.png"
    caption: "Figure 78. Single-Tone FFT at f_{IN} = 1800 MHz"
    type: "characteristic_curve"
    page: 39
  - file: "ad9081/figures/ad9081-f079.png"
    caption: "Figure 79. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz"
    type: "characteristic_curve"
    page: 39
  - file: "ad9081/figures/ad9081-f080.png"
    caption: "Figure 80. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz"
    type: "characteristic_curve"
    page: 39
  - file: "ad9081/figures/ad9081-f081.png"
    caption: "Figure 81. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz"
    type: "characteristic_curve"
    page: 39
  - file: "ad9081/figures/ad9081-f082.png"
    caption: "Figure 82. Single-Tone FFT at f_{IN} = 2700 MHz"
    type: "characteristic_curve"
    page: 40
  - file: "ad9081/figures/ad9081-f083.png"
    caption: "Figure 83. Single-Tone FFT at f_{IN} = 3600 MHz"
    type: "characteristic_curve"
    page: 40
  - file: "ad9081/figures/ad9081-f084.png"
    caption: "Figure 84. Single-Tone FFT at f_{IN} = 4500 MHz"
    type: "characteristic_curve"
    page: 40
  - file: "ad9081/figures/ad9081-f085.png"
    caption: "Figure 85. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz"
    type: "characteristic_curve"
    page: 40
  - file: "ad9081/figures/ad9081-f086.png"
    caption: "Figure 86. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz"
    type: "characteristic_curve"
    page: 40
  - file: "ad9081/figures/ad9081-f087.png"
    caption: "Figure 87. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz"
    type: "characteristic_curve"
    page: 40
  - file: "ad9081/figures/ad9081-f088.png"
    caption: "Figure 88. Single-Tone FFT at f_{IN} = 5400 MHz"
    type: "characteristic_curve"
    page: 41
  - file: "ad9081/figures/ad9081-f089.png"
    caption: "Figure 89. Single-Tone FFT at f_{IN} = 6300 MHz"
    type: "characteristic_curve"
    page: 41
  - file: "ad9081/figures/ad9081-f090.png"
    caption: "Figure 90. Single-Tone FFT at f_{IN} = 7200 MHz"
    type: "characteristic_curve"
    page: 41
  - file: "ad9081/figures/ad9081-f091.png"
    caption: "Figure 91. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz"
    type: "characteristic_curve"
    page: 41
  - file: "ad9081/figures/ad9081-f092.png"
    caption: "Figure 92. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz"
    type: "characteristic_curve"
    page: 41
  - file: "ad9081/figures/ad9081-f093.png"
    caption: "Figure 93. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz"
    type: "characteristic_curve"
    page: 41
  - file: "ad9081/figures/ad9081-f094.png"
    caption: "Figure 94. Two-Tone FFT, f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 42
  - file: "ad9081/figures/ad9081-f095.png"
    caption: "Figure 95. Two-Tone FFT, f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 42
  - file: "ad9081/figures/ad9081-f096.png"
    caption: "Figure 96. SNR and SFDR  vs. Input Frequency with A_{IN} =-1 dBFS"
    type: "characteristic_curve"
    page: 42
  - file: "ad9081/figures/ad9081-f097.png"
    caption: "Figure 97. Two-Tone FFT, f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 42
  - file: "ad9081/figures/ad9081-f098.png"
    caption: "Figure 98. Two-Tone FFT, f_{IN1} = 5.575 GHz, f_{IN2} = 5.425 GHz, A_{IN1} and A_{IN2} = -7 dBFS"
    type: "characteristic_curve"
    page: 42
  - file: "ad9081/figures/ad9081-f099.png"
    caption: "Figure 99. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS"
    type: "characteristic_curve"
    page: 42
  - file: "ad9081/figures/ad9081-f101.png"
    caption: "Figure 100. 324-Ball Ball Grid Array, Thermally Enhanced [BGA_ED] (BP-324-3) Dimensions shown in millimeters"
    type: "other"
    page: 45
  - file: "ad9081/figures/ad9081-f102.png"
    caption: "Figure 3. Timing Diagram for 3-Wire Read Operation"
    type: "timing_diagram"
    page: 20
curves:
  - file: "ad9081/curves/dac0-fundamental-output-power-vs-fout-across-fdac-at-0-dbfs.csv"
    caption: "Figure 24. DAC0 Fundamental Output Power vs. f_{OUT} Across f_{DAC}, at 0 dBFS"
    figure: "ad9081/figures/ad9081-f024.png"
    page: 30
    x_unit: "MHz"
    y_unit: "dBm"
    conditions: "0 dBFS"
  - file: "ad9081/curves/harmonics-hd2-and-hd3-vs-input-frequency-with-a-in-1-dbfs.csv"
    caption: "Figure 99. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS"
    figure: "ad9081/figures/ad9081-f099.png"
    page: 42
    x_unit: "MHz"
    y_unit: "dBc"
    conditions: "A_{IN} = -1 dBFS"
  - file: "ad9081/curves/harmonics-hd2-and-hd3-vs-sample-frequency-f-s-f-in-450-mhz.csv"
    caption: "Figure 70. Harmonics (HD2 and HD3) vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz"
    figure: "ad9081/figures/ad9081-f070.png"
    page: 37
    x_unit: "GHz"
    y_unit: "dBFS"
  - file: "ad9081/curves/harmonics-hd2-hd3-and-interleaving-vs-die-temperature-f-in-1-85-ghz.csv"
    caption: "Figure 69. Harmonics (HD2, HD3, and Interleaving) vs. Die Temperature, f_{IN} = 1.85 GHz"
    figure: "ad9081/figures/ad9081-f069.png"
    page: 37
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "f_{IN} = 1.85 GHz"
  - file: "ad9081/curves/hd2-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv"
    caption: "Figure 7. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C"
    figure: "ad9081/figures/ad9081-f007.png"
    page: 27
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd2-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv"
    caption: "Figure 10. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B"
    figure: "ad9081/figures/ad9081-f010.png"
    page: 27
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd2-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-interpolation-1-m.csv"
    caption: "Figure 6. HD2 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C"
    figure: "ad9081/figures/ad9081-f006.png"
    page: 27
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd2-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv"
    caption: "Figure 9. HD2 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C"
    figure: "ad9081/figures/ad9081-f009.png"
    page: 27
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd3-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv"
    caption: "Figure 12. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C"
    figure: "ad9081/figures/ad9081-f012.png"
    page: 28
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd3-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv"
    caption: "Figure 15. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B"
    figure: "ad9081/figures/ad9081-f015.png"
    page: 28
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd3-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-interpolation-1-m.csv"
    caption: "Figure 8. HD3 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C"
    figure: "ad9081/figures/ad9081-f008.png"
    page: 27
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/hd3-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv"
    caption: "Figure 11. HD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C"
    figure: "ad9081/figures/ad9081-f011.png"
    page: 27
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/imd3-vs-f-out-over-f-dac-digital-scale-7-dbfs-imd3-is-a-two-tone-test-and-the-sc.csv"
    caption: "Figure 20. IMD3 vs. f_{OUT} over f_{DAC} , Digital Scale -7 dBFS, IMD3 is a Two-Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital Scale"
    figure: "ad9081/figures/ad9081-f020.png"
    page: 29
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/imd3-vs-fout-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv"
    caption: "Figure 19. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital"
    figure: "ad9081/figures/ad9081-f019.png"
    page: 29
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/imd3-vs-fout-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv"
    caption: "Figure 22. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital"
    figure: "ad9081/figures/ad9081-f022.png"
    page: 29
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/imd3-vs-fout-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv"
    caption: "Figure 21. IMD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital"
    figure: "ad9081/figures/ad9081-f021.png"
    page: 29
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/imd3-vs-fout-over-digital-scale-mode-17b-6-gsps-dac-sample-rate-channel-interpol.csv"
    caption: "Figure 18. IMD3 vs. f_{OUT} over Digital Scale (Mode 17B), 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C,"
    figure: "ad9081/figures/ad9081-f018.png"
    page: 29
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/measured-input-bandwidth-adc-input-on-ad9081-fmca-ebz-no-matching-network.csv"
    caption: "Figure 74. Measured Input Bandwidth ADC Input on AD9081-FMCA-EBZ (No Matching Network)"
    figure: "ad9081/figures/ad9081-f074.png"
    page: 38
    x_unit: "GHz"
    y_unit: "dB"
  - file: "ad9081/curves/power-vs-die-temperature-f-in-1-85-ghz-a-in-1-dbfs.csv"
    caption: "Figure 68. Power vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS"
    figure: "ad9081/figures/ad9081-f068.png"
    page: 37
    x_unit: "°C"
    y_unit: "A"
  - file: "ad9081/curves/power-vs-sample-frequency-f-s-f-in-450-mhz.csv"
    caption: "Figure 71. Power vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz"
    figure: "ad9081/figures/ad9081-f071.png"
    page: 37
    x_unit: "GHz"
    y_unit: "A"
    conditions: "f_{IN} = 450 MHz"
  - file: "ad9081/curves/sfdr-worst-in-band-spurious-vs-f-out-over-f-dac-with-0-dbfs-tone-level.csv"
    caption: "Figure 23. SFDR, Worst In-Band Spurious vs. f_{OUT} over f_{DAC} , with 0 dBFS Tone Level"
    figure: "ad9081/figures/ad9081-f023.png"
    page: 29
    x_unit: "MHz"
    y_unit: "dBc"
    conditions: "0 dBFS tone level"
  - file: "ad9081/curves/sfdr-worst-spurious-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-.csv"
    caption: "Figure 17. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B"
    figure: "ad9081/figures/ad9081-f017.png"
    page: 28
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/sfdr-worst-spurious-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-i.csv"
    caption: "Figure 13. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C"
    figure: "ad9081/figures/ad9081-f013.png"
    page: 28
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/sfdr-worst-spurious-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-i.csv"
    caption: "Figure 16. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C"
    figure: "ad9081/figures/ad9081-f016.png"
    page: 28
    x_unit: "MHz"
    y_unit: "dBc"
  - file: "ad9081/curves/single-sideband-phase-noise-vs-frequency-offset-for-different.csv"
    caption: "Figure 27. Single Sideband Phase Noise vs. Frequency Offset for Different"
    figure: "ad9081/figures/ad9081-f027.png"
    page: 30
    x_unit: "Hz"
    y_unit: "dBc/Hz"
  - file: "ad9081/curves/single-sideband-phase-noise-vs-frequency-offset-for-different-clock-input-power-.csv"
    caption: "Figure 25. Single Sideband Phase Noise vs. Frequency Offset for Different Clock Input Power (P_{CLK} ), f_{OUT} = 1.8 GHz, External 12 GHz Clock Input with Clock PLL Disabled"
    figure: "ad9081/figures/ad9081-f025.png"
    page: 30
    x_unit: "Hz"
    y_unit: "dBc/Hz"
  - file: "ad9081/curves/single-sideband-phase-noise-vs-frequency-offset-for-different-dac-output-frequen.csv"
    caption: "Figure 28. Single Sideband Phase Noise vs. Frequency Offset for Different DAC Output Frequencies (f_{OUT} ), External 12 GHz Clock Input with Clock PLL Disabled"
    figure: "ad9081/figures/ad9081-f028.png"
    page: 30
    x_unit: "Hz"
    y_unit: "dBc/Hz"
  - file: "ad9081/curves/single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-over-f-dac-12-bit-reso.csv"
    caption: "Figure 29. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , 12-Bit Resolution, Shuffle On, Mode 24C"
    figure: "ad9081/figures/ad9081-f029.png"
    page: 30
    x_unit: "MHz"
    y_unit: "dBc/Hz"
  - file: "ad9081/curves/single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-over-f-dac-shuffle-on-.csv"
    caption: "Figure 26. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , Shuffle On, 16-Bit Resolution, Mode 15C"
    figure: "ad9081/figures/ad9081-f026.png"
    page: 30
    x_unit: "MHz"
    y_unit: "dBc/Hz"
  - file: "ad9081/curves/single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-shuffle-off-vs-shuffle.csv"
    caption: "Figure 33. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 12-Bit Resolution, Mode 24C"
    figure: "ad9081/figures/ad9081-f033.png"
    page: 31
    x_unit: "MHz"
    y_unit: "dBc/Hz"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-1800-mhz.csv"
    caption: "Figure 81. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz"
    figure: "ad9081/figures/ad9081-f081.png"
    page: 39
    x_unit: "dBFS"
    y_unit: "dBc and dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-2700-mhz.csv"
    caption: "Figure 85. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz"
    figure: "ad9081/figures/ad9081-f085.png"
    page: 40
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-3600-mhz.csv"
    caption: "Figure 86. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz"
    figure: "ad9081/figures/ad9081-f086.png"
    page: 40
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-450-mhz.csv"
    caption: "Figure 39. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz"
    figure: "ad9081/figures/ad9081-f039.png"
    page: 32
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-4500-mhz.csv"
    caption: "Figure 87. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz"
    figure: "ad9081/figures/ad9081-f087.png"
    page: 40
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-5400-mhz.csv"
    caption: "Figure 91. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz"
    figure: "ad9081/figures/ad9081-f091.png"
    page: 41
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-6300-mhz.csv"
    caption: "Figure 92. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz"
    figure: "ad9081/figures/ad9081-f092.png"
    page: 41
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-7200-mhz.csv"
    caption: "Figure 93. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz"
    figure: "ad9081/figures/ad9081-f093.png"
    page: 41
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-900-mhz.csv"
    caption: "Figure 80. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz"
    figure: "ad9081/figures/ad9081-f080.png"
    page: 39
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/single-tone-sfdr-and-snr-vs-ain-at-fin-450-mhz.csv"
    caption: "Figure 79. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz"
    figure: "ad9081/figures/ad9081-f079.png"
    page: 39
    x_unit: "dBFS"
    y_unit: "dBc AND dBFS"
  - file: "ad9081/curves/snr-and-sfdr-vs-die-temperature-f-in-1-85-ghz-a-in-1-dbfs.csv"
    caption: "Figure 66. SNR and SFDR vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS"
    figure: "ad9081/figures/ad9081-f066.png"
    page: 37
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS"
  - file: "ad9081/curves/snr-and-sfdr-vs-input-frequency-with-a-in-1-dbfs.csv"
    caption: "Figure 96. SNR and SFDR  vs. Input Frequency with A_{IN} =-1 dBFS"
    figure: "ad9081/figures/ad9081-f096.png"
    page: 42
    x_unit: "MHz"
    y_unit: "dBFS"
  - file: "ad9081/curves/snr-and-sfdr-vs-sample-frequency-f-s-f-in-450-mhz.csv"
    caption: "Figure 67. SNR and SFDR vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz"
    figure: "ad9081/figures/ad9081-f067.png"
    page: 37
    x_unit: "GHz"
    y_unit: "dBFS"
  - file: "ad9081/curves/snr-vs-input-frequency-direct-clock-vs-on-chip-pll-clock-f-s-4-ghz-a-in-1-dbfs.csv"
    caption: "Figure 64. SNR vs. Input Frequency, Direct Clock vs. On-Chip PLL Clock,  f_{S}  = 4 GHz, A_{IN} = -1 dBFS"
    figure: "ad9081/figures/ad9081-f064.png"
    page: 36
    x_unit: "MHz"
    y_unit: "dBFS"
  - file: "ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-1-775-ghz-f-in2-1-825-ghz.csv"
    caption: "Figure 57. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz"
    figure: "ad9081/figures/ad9081-f057.png"
    page: 35
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-2-675-ghz-f-in2-2-725-ghz.csv"
    caption: "Figure 58. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz"
    figure: "ad9081/figures/ad9081-f058.png"
    page: 35
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-3-575-ghz-f-in2-3-625-ghz.csv"
    caption: "Figure 59. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz"
    figure: "ad9081/figures/ad9081-f059.png"
    page: 35
    x_unit: "dBFS"
    y_unit: "dBFS"
  - file: "ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-5-375-ghz-f-in2-5-425-ghz.csv"
    caption: "Figure 63. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz"
    figure: "ad9081/figures/ad9081-f063.png"
    page: 36
    x_unit: "dBFS"
    y_unit: "dBFS"
agentforge:
  part_number: "AD9081"
  datasheet_revision: "0"
  repairs: 8
  reading_order: "geometry"
---

# AD9081 — MxFE Quad, 16-Bit, 12 GSPS RF DAC and Quad, 12-Bit, 4 GSPS RF ADC

*Datasheet: [AD9081 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ad9081.pdf)*

### FEATURES

- Flexible, reconfigurable common platform design
  - 4 DACs and 4 ADCs (4D4A)
  - Supports single, dual, and quad band
  - Datapaths and DSP blocks are fully bypassable
  - DAC to ADC sample rate ratios of 1, 2, 3, and 4
  - On-chip PLL with multichip synchronization
    - External RFCLK input option for off-chip PLL
- Maximum DAC sample rate up to 12 GSPS
  - Maximum data rate up to 12 GSPS using JESD204C
  - Useable analog bandwidth to 8 GHz
- Maximum ADC sample rate up to 4 GSPS
  - Maximum data rate up to 4 GSPS using JESD204C
  - 7.5 GHz analog input full power bandwidth (-3 dB)
- ADC ac performance at 4 GSPS, input at -2.7 GHz, -1 dBFS
  - Full-scale input voltage: 1.4 V p-p
  - Noise density: -147.5 dBFS/Hz
  - Noise figure: 26.8 dB
  - HD2: -67 dBFS
  - HD3: -73 dBFS
  - Worst other (excluding HD2 and HD3): -79 dBFS at 2.7 GHz
- DAC ac performance at 12 GSPS
  - Full-scale output current range: 6.43 mA to 37.75 mA
  - Two-tone IMD3 (-7 dBFS per tone): -78.9 dBc
  - NSD, single-tone at 3.7 GHz: -155.1 dBc/Hz
  - SFDR, single-tone at 3.7 GHz: -70 dBc
- Versatile digital features
  - Configurable or bypassable DDCs and DUCs
    - 8 fine complex DUCs and 4 coarse complex DUCs
    - 8 fine complex DDCs and 4 coarse complex DDCs
    - 48-bit NCO per DUC or DDC
- Programmable 192-tap PFIR filter for receive equalization
  - Supports 4 different profile settings loaded via GPIO
- Programmable delay per datapath
- Receive AGC support
  - Fast detect with low latency for fast AGC control
  - Signal monitor for slow AGC control
- Transmit DPD support
  - Fine DUC channel gain control and delay adjust
  - Coarse DDC delay adjust for DPD observation path
- Auxiliary features
  - Fast frequency hopping and direct digital synthesis (DDS)
  - Low latency loopback mode (receive datapath data can be routed to the transmit datapaths)
  - ADC clock driver with selectable divide ratios
  - Power amplifier downstream protection circuitry
  - On-chip temperature monitoring unit
  - Flexible GPIO pins
  - TDD power savings option and sharing ADCs
- SERDES JESD204B/JESD204C interface, 16 lanes up to 24.75 Gbps
  - 8 lanes JESD204B/C transmitter (JTx) and 8 lanes JESD204B/C receiver (JRx)
  - JESD204B compliance with the maximum 15.5 Gbps
  - JESD204C compliance with the maximum 24.75 Gbps
  - Supports real or complex digital data (8-, 12-, 16-, or 24-bit)
- 15 mm × 15 mm, 324-ball BGA with 0.8 mm pitch

### APPLICATIONS

- Wireless communications infrastructure
- Microwave point to point, E-band, and 5G mmWave
- Broadband communications systems
- DOCSIS 3.1 and 4.0 CMTS
- Phased array radar and electronic warfare
- Electronic test and measurement systems

### GENERAL DESCRIPTION

The AD9081 mixed signal front end (MxFE®) is a highly integrated device with four 16-bit, 12 GSPS maximum sample rate, RF digitalto-analog converter (DAC) cores, and four 12-bit, 4 GSPS rate, RF analog-to-digital converter (ADC) cores. The AD9081 is well suited for applications requiring both wideband ADCs and DACs to process signal(s) that have wide instantaneous bandwidth. The device features eight transmit and eight receive lanes that support 24.75 Gbps/lane JESD204C or 15.5 Gbps/lane JESD204B standards. The device also has an on-chip clock multiplier, and a digital signal processing (DSP) capability targeted at either wideband or multiband direct to RF applications. The DSP datapaths can be bypassed to allow a direct connection between the converter cores and the JESD204 data transceiver port. The device also features low latency loopback and frequency hopping modes targeted at phase array radar system and electronic warfare applications. Two models for the AD9081 are offered. The 4D4AC model supports the full instantaneous channel bandwidth, whereas the 4D4AB model supports a maximum instantaneous bandwidth of 600 MHz per channel by automatically configuring the DSP to limit the instantaneous bandwidth at startup. See the Ordering Guide for more information.

### TABLE OF CONTENTS

- Features...1
- Applications...1
- General Description...1
- Functional Block Diagram...3
- Specifications...4
  - Recommended Operating Conditions...4
  - Power Consumption...4
  - DAC DC Specifications...5
  - ADC DC Specifications...6
  - Clock Inputs and Outputs...7
  - Clock Input and Phase-Locked Loop (PLL) Frequency Specifications...7
- DAC Sample Rate Specifications...8
- ADC Sample Rate Specifications...9
- Input Data Rate Specifications...10
- NCO Frequency Specifications...11
- JESD204B and JESD204C Interface Electrical and Speed Specifications...11
  - CMOS Pin Specifications...13
  - DAC AC Specifications...13
  - ADC AC Specifications...16
  - Timing Specifications...19
- Absolute Maximum Ratings...21
  - Thermal Resistance...21
  - ESD Caution...21
- Pin Configuration and Function Descriptions...22
- Typical Performance Characteristics...27
  - DAC...27
  - ADC: 4 GSPS...32
  - ADC: 3 GSPS...39
- Theory of Operation...43
- Applications Information...44
- Outline Dimensions...45
  - Ordering Guide...45
- Evaluation Boards...45

### REVISION HISTORY

4/2021-Revision 0: Initial Version

### FUNCTIONAL BLOCK DIAGRAM

Figure 1.

![Figure 1.](ad9081/figures/ad9081-f001.png)

*Figure 1.*

### SPECIFICATIONS

### RECOMMENDED OPERATING CONDITIONS

Successful DAC calibration is required during the device initialization phase that occurs shortly after power-up to ensure long-term reliability of the DAC core circuitry. Refer to the UG-1578 user guide for more information on device initialization.

**Table 1.** ([table-00-p4-spec.csv](ad9081/tables/table-00-p4-spec.csv), p. 4)

| PARAMETER | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|
| OPERATING JUNCTION TEMPERATURE (T_{J}) | −40 |  | +120 | °C |
| **ANALOG SUPPLY VOLTAGE RANGE** |  |  |  |  |
| AVDD2, BVDD2, RVDD2 | 1.9 | 2.0 | 2.1 | V |
| AVDD1, AVDD1_ADC, CLKVDD1, FVDD1, VDD1_NVG1 | 0.95 | 1.0 | 1.05 | V |
| **DIGITAL SUPPLY VOLTAGE RANGE** |  |  |  |  |
| DVDD1, DVDD1_RT, DCLKVDD1, DAVDD1 | 0.95 | 1.0 | 1.05 | V |
| DVDD1P8 | 1.7 | 1.8 | 2.1 | V |
| **SERIALIZER/DESERIALIZER (SERDES) SUPPLY VOLTAGE RANGE** |  |  |  |  |
| SVDD2_PLL | 1.9 | 2.0 | 2.1 | V |
| SVDD1, SVDD1_PLL | 0.95 | 1.0 | 1.05 | V |

### POWER CONSUMPTION

Typical at nominal supplies and maximum at 5% supplies. For the minimum and maximum values, T_{J} varies between -40°C and +120°C. For the typical values, T_{A} = 25°C, which corresponds to T_{J} = 80°C, unless otherwise noted.

DAC datapath with a complex I/Q data rate frequency (f_{IQ_DATA} ) = 2 GSPS, interpolation of 6×, and DAC frequency (f_{DAC} ) of 12 GSPS. JESD204C mode of 24C (L = 8, M = 8, F = 3, S = 2, K = 256, E = 3, N = 12, NP = 12).

ADC datapath with DDC bypassed (no decimation), and f_{ADC} of 4 GSPS. JESD204C mode of 27C (L = 8, M = 4, F = 3, S = 4, K = 256, E = 3, N = 12, NP = 12).

See the UG-1578 user guide for further information on the JESD204B and JESD204C mode configurations and a detailed description of the settings referenced throughout this data sheet. A table showing other operational modes and the corresponding typical and maximum power consumption numbers is included.

### Table 2. Power Consumption

**Table 2. Power Consumption** ([table-01-p4-spec.csv](ad9081/tables/table-01-p4-spec.csv), p. 4)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **CURRENTS** |  |  |  |  |  |
| AVDD2 (I_{AVDD2}) | 2.0 V supply |  | 190 | 205 | mA |
| BVDD2 (I_{BVDD2}) + RVDD2 (I_{RVDD2}) | 2.0 V supply |  | 295 | 355 | mA |
| AVDD2_PLL (I_{AVDD2_PLL}) +SVDD2_PLL (I_{SVDD2_PLL}) | 2.0 V supply |  | 45 | 55 | mA |
| Power Dissipation for 2 V Supplies | 2.0 V supply total power dissipation |  | 1.1 | 1.2 | W |
| PLLCLKVDD1 (I_{PLLCLKVDD1}) | 1.0 V supply |  | 15 | 25 | mA |
| AVDD1 (I_{AVDD1}) + DCLKVDD1(I_{DCLKVDD1}) | 1.0 V supply |  | 1000 | 1185 | mA |
| AVDD1_ADC (I_{AVDD1_ADC}) | 1.0 V supply |  | 1825 | 2155 | mA |
| CLKVDD1 (I_{CLKVDD1}) | 1.0 V supply |  | 70 | 125 | mA |
| FVDD1 (I_{FVDD1}) | 1.0 V supply |  | 45 | 70 | mA |
| VDD1_NVG (I_{VDD1_NVG}) | 1.0 V supply |  | 280 | 345 | mA |
| DAVDD1 (I_{DAVDD1}) | 1.0 V supply |  | 1600 | 1835 | mA |
| DVDD1 (I_{DVDD1}) | 1.0 V supply |  | 2580 | 3530 | mA |
| DVDD1_RT (I_{DVDD1_RT}) | 1.0 V supply |  | 720 | 840 | mA |
| SVDD1 (I_{SVDD1}) + SVDD1_PLL (I_{SVDD1_PLL}) | 1.0 V supply |  | 1920 | 2570 | mA |
| Power Dissipation for 1 V Supplies | 1.0 V supply total power dissipation |  | 10.1 | 13.1 | W |
| DVDD1P8 (I_{DVDD1P8}) | 1.8 V supply |  | 7 | 10 | mA |
| Total Power Dissipation | Total power dissipation of 2 V and 1 V supplies |  | 11.2 | 14.3 | W |

### DAC DC SPECIFICATIONS

Nominal supplies with DAC full-scale output current (I_{OUTFS} ) = 26 mA, unless otherwise noted. ADC setup in 4 GSPS, full bandwidth mode (all digital downconverters bypassed). For the minimum and maximum values, T_{J} = -40°C to +120°C, and for the typical values, T_{A} = 25°C, which corresponds to T_{J} = 80°C, unless otherwise noted.

**Table 3. DAC DC Specifications** ([table-02-p5-spec.csv](ad9081/tables/table-02-p5-spec.csv), p. 5)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| DAC RESOLUTION |  | 16 |  |  | Bit |
| **DAC ACCURACY** |  |  |  |  |  |
| Gain Error |  |  | 1.5 |  | % FSR |
| Gain Matching |  |  | 0.7 |  | % FSR |
| Integral Nonlinearity (INL) | Shuffling disabled |  | 8.0 |  | LSB |
| Differential Nonlinearity (DNL) | Shuffling disabled |  | 3.5 |  | LSB |
| **DAC ANALOG OUTPUTS** | DACxP and DACxN |  |  |  |  |
| **Full-Scale Output Current Range** | AC coupling, setting resistance (R_{SET}) = 5 kΩ |  |  |  |  |
| AC Coupling | Output common-mode voltage (V_{CM}) = 0 V | 6.43 | 26.5 | 37.75 | mA |
| DC Coupling | 50 Ω shunt to a negative supply, forcing V_{CM} = 0 V | 6.43 |  | 37.75 | mA |
| DC Coupling | 50 Ω shunt to GND, forcing V_{CM} = 0.3 V | 6.43 |  | 20[^1] | mA |
| Full-Scale Sine Wave Output Power with AC Coupling[^2] | Ideal 2:1 balun interface to 50 Ω |  |  |  |  |
| I_{OUTFS} = 26.5 mA |  |  | 3.3 |  | dBm |
| I_{OUTFS} = 37.75 mA |  |  | 7 |  | dBm |
| Common-Mode Output Voltage (VCM_{OUT}) |  |  | 0 |  | V |
| AC Coupling | Bias each output to GND across a shunt inductor |  | 0 |  | V |
| DC Coupling | Bias each output to a negative voltage rail across a 25 Ω to 200 Ω resistor, selected such that VCM_{OUT} = 0 V, VCM_{OUT} = 0.3 V is with a 25 Ω resistor to GND and I_{OUTFS} = 20 mA |  | 0 | 0.3 | V |
| Differential Resistance |  |  | 100 |  | Ω |

- **Note 1:** For dc-coupled applications, the maximum full-scale output current is limited by the maximum VCM_{OUT} specification.
- **Note 2:** The actual measured full-scale power is frequency dependent due to DAC sinc response, impedance mismatch loss, and balun insertion loss.

### ADC DC SPECIFICATIONS

Nominal supplies with DAC I_{OUTFS} = 26 mA, unless otherwise noted. ADC setup in 4 GSPS, full bandwidth mode (all digital downconverters bypassed). For the minimum and maximum values, T_{J} = -40°C to +120°C, and for the typical values, T_{A} = 25°C, which corresponds to T_{J} = 80°C, unless otherwise noted.

**Table 4. ADC DC Specifications** ([table-03-p6-spec.csv](ad9081/tables/table-03-p6-spec.csv), p. 6)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| ADC RESOLUTION |  | 12 |  |  | Bit |
| **ADC ACCURACY** |  |  |  |  |  |
| No Missing Codes |  |  | Guaranteed |  |  |
| Offset Error |  |  | −0.20 |  | % FSR |
| Offset Matching |  |  | 0.05 |  | % FSR |
| Gain Error |  |  | −0.71 |  | % FSR |
| Gain Matching |  |  | 1.2 |  | % FSR |
| DNL |  |  | ±1.9 |  | LSB |
| INL |  |  | ±0.5 |  | LSB |
| **ADC ANALOG INPUTS** | ADCxP and ADCxN |  |  |  |  |
| Differential Input Voltage |  |  | 1.4 |  | V p-p |
| Full-Scale Sine Wave Input Power | Input power level resulting 0 dBFS tone level on fast Fourier transform (FFT) |  | 3.9 |  | dBm |
| Common-Mode Input Voltage (VCM_{IN}) | AC-coupled, equal to voltage at VCMx for ADCx input |  | 1 |  | V |
| Differential Input Resistance |  |  | 100 |  | Ω |
| Differential Input Capacitance |  |  | 0.4 |  | pF |
| Return Loss | <2.7 GHz |  | −4.3 |  | dB |
| Return Loss | 2.7 GHz to 3.8 GHz |  | −3.6 |  | dB |
| Return Loss | 3.8 GHz to 5.4 GHz |  | −2.9 |  | dB |

### CLOCK INPUTS AND OUTPUTS

For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply, unless otherwise noted.

**Table 5. Clock Inputs and Outputs** ([table-04-p7-spec.csv](ad9081/tables/table-04-p7-spec.csv), p. 7)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **CLOCK INPUTS** | CLKINP and CLKINN |  |  |  |  |
| Differential Input Power | Direct RF clock |  |  |  |  |
| Minimum |  |  |  | 0 | dBm |
| Maximum |  |  |  | 6 | dBm |
| Common-Mode Voltage | AC-coupled |  |  | 0.5 | V |
| Differential Input Resistance |  |  |  | 100 | Ω |
| Differential Input Capacitance |  |  |  | 0.3 | pF |
| **CLOCK OUTPUTS (ADC CLOCK DRIVER)** | ADCDRVP and ADCDRVN |  |  |  |  |
| Differential Output Voltage Magnitude[^1] | 1.5 GHz |  |  | 740 | mV p-p |
| Differential Output Voltage Magnitude[^1] | 2.0 GHz |  |  | 690 | mV p-p |
| Differential Output Voltage Magnitude[^1] | 3.0 GHz |  |  | 640 | mV p-p |
| Differential Output Voltage Magnitude[^1] | 6.0 GHz |  |  | 490 | mV p-p |
| Differential Output Resistance |  |  |  | 100 | Ω |
| Common-Mode Voltage | AC-coupled |  |  | 0.5 | V |

- **Note 1:** Measured with differential 100 Ω load and less than 2 mm of printed circuit board (PCB) trace from package ball.

### CLOCK INPUT AND PHASE-LOCKED LOOP (PLL) FREQUENCY SPECIFICATIONS

For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply, unless otherwise noted.

**Table 6. Clock Input and PLL Frequency Specifications** ([table-05-p7-spec.csv](ad9081/tables/table-05-p7-spec.csv), p. 7)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| CLOCK INPUTS (CLKINP, CLKINN) FREQUENCY RANGES |  | 25 |  | 12000 | MHz |
| PHASE FREQUENCY DETECTOR (PFD) INPUT FREQUENCY RANGES |  | 25 |  | 750 | MHz |
| **FREQUENCY RANGES ACCORDING TO CLOCK PATH CONFIGURATION** |  |  |  |  |  |
| Direct Clock (PLL Off) |  | 2900[^1] |  | 12000 | MHz |
| PLL Reference Clock (PLL On) | M divider set to divide by 1 | 25 |  | 750 | MHz |
| PLL Reference Clock (PLL On) | M divider set to divide by 2 | 50 |  | 1500 | MHz |
| PLL Reference Clock (PLL On) | M divider set to divide by 3 | 75 |  | 2250 | MHz |
| PLL Reference Clock (PLL On) | M divider set to divide by 4 | 100 |  | 3000 | MHz |
| **PLL VOLTAGE CONTROLLED OSCILLATOR (VCO) FREQUENCY RANGES** |  |  |  |  |  |
| **VCO Output** |  |  |  |  |  |
| Divide by | D divider set to divide by 1 | 5.8 |  | 12 | GHz |
| Divide by 2 | D divider set to divide by 2 | 2.9 |  | 6 | GHz |
| Divide by 3 | D divider set to divide by 3 | 1.93333 |  | 4 | GHz |
| Divide by 4 | D divider set to divide by 4 | 1.45 |  | 3 | GHz |

- **Note 1:** The minimum direct clock frequency is limited by the minimum DAC (core) sample rate, as specified in  Table 7. The clock receiver can accommodate the full range between the minimum PLL reference clock frequency and the maximum direct clock frequency.

### DAC SAMPLE RATE SPECIFICATIONS

Nominal supplies. For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply. For the typical values, T_{A} = 25°C, which corresponds to T_{J} = 80°C, unless otherwise noted.

**Table 7. DAC Sample Rate Specifications** ([table-06-p8-spec.csv](ad9081/tables/table-06-p8-spec.csv), p. 8)

| PARAMETER | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|
| **DAC SAMPLE RATE[^1]** |  |  |  |  |
| Minimum |  |  | 2.9 | GSPS |
| Maximum | 12 |  |  | GSPS |

- **Note 1:** Pertains to the update rate of the DAC core, independent of the datapath and JESD204 mode configuration.

### ADC SAMPLE RATE SPECIFICATIONS

Nominal supplies. For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply. For the typical values, T_{A} = 25°C, which corresponds to T_{J} = 80°C, unless otherwise noted.

**Table 8. ADC Sample Rate Specifications** ([table-07-p9-spec.csv](ad9081/tables/table-07-p9-spec.csv), p. 9)

| PARAMETER | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|
| **ADC SAMPLE RATE[^1]** |  |  |  |  |
| Minimum |  |  | 1.45 | GSPS |
| Maximum | 4 |  |  | GSPS |
| Aperture Jitter[^2] |  | 65 |  | fs rms |

- **Note 1:** Pertains to the update rate of the ADC core, independent of the datapath and JESD204 mode configuration.
- **Note 2:** Measured using a signal-to-noise ratio (SNR) degradation method with the DAC disabled, clock divider = 1, ADC frequency (f_{ADC}) = 4 GSPS, and input frequency (f_{IN}) = 5.55 GHz.

### INPUT DATA RATE SPECIFICATIONS

For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply, unless otherwise noted.

### Table 9. Input Data Rate Specifications

**Table 9. Input Data Rate Specifications** ([table-08-p10-spec.csv](ad9081/tables/table-08-p10-spec.csv), p. 10)

| PARAMETER[^1][^2] | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **MAXIMUM DATA RATE PER NUMBER OF ACTIVE DAC OUTPUTS** |  |  |  |  |  |
| MAXIMUM DATA RATE PER NUMBER OF ACTIVE DAC OUTPUTS | Single DAC, fine digital upconverter (FDUC) and coarse digital upconverter (CDUC) bypassed (1× interpolation), 16-bit resolution, limited by the maximum DAC clock rate |  |  | 12000 | MSPS |
| MAXIMUM DATA RATE PER NUMBER OF ACTIVE DAC OUTPUTS | Quad DAC, FDUC and CDUC bypassed (1× interpolation), 12-bit resolution, limited by the maximum JESD204C link throughput (M = 4, L = 8) |  |  | 4000 | MSPS |
| **MAXIMUM COMPLEX (I/Q) DATA RATE PER NUMBER OF ACTIVE INPUT DATA CHANNELS** |  |  |  |  |  |
| MAXIMUM COMPLEX (I/Q) DATA RATE PER NUMBER OF ACTIVE INPUT DATA CHANNELS | 1 channel: FDUC bypassed, 1 CDUC enabled, 12-bit or 16-bit resolution, limited by the maximum CDUC NCO clock rate |  |  | 6000 | MSPS |
| MAXIMUM COMPLEX (I/Q) DATA RATE PER NUMBER OF ACTIVE INPUT DATA CHANNELS | 2 channels: FDUC bypassed, 2 CDUCs enabled, 12-bit resolution, limited by the maximum JESD204C link throughput (M = 4, L = 8) |  |  | 4000 | MSPS |
| MAXIMUM COMPLEX (I/Q) DATA RATE PER NUMBER OF ACTIVE INPUT DATA CHANNELS | 4 channels: FDUC bypassed, 4 CDUCs enabled, 12-bit resolution, limited by the maximum JESD204C link throughput (M = 8, L = 8) |  |  | 2000 | MSPS |
| MAXIMUM COMPLEX (I/Q) DATA RATE PER NUMBER OF ACTIVE INPUT DATA CHANNELS | 8 channels: 8 FDUCs enabled, one or more CDUC enabled, 12-bit or 16-bit resolution, limited by the maximum FDUC NCO clock rate divided by the minimum 2× interpolation rate required to enable the FDUC |  |  | 750 | MSPS |

- **Note 1:** The values listed for these parameters are the maximum possible when considering all JESD204 modes of operation. Some modes are more limiting, based on other parameters.
- **Note 2:** The interpolation filters in the Tx datapath have a total complex filter bandwidth of 80% of the data rate, combining the 40% bandwidth in the I path and 40% bandwidth in the Q path. Similarly, the decimation stages inside the Rx datapath use filters with a total complex filter bandwidth of 81.4%. Therefore, the maximum allowed instantaneous complex signal bandwidth (iBW) per channel is calculated as iBW = (complex I/Q data rate per channel) × (total complex filter bandwidth).

### NCO FREQUENCY SPECIFICATIONS

For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply, unless otherwise noted.

**Table 10. NCO Frequency Specifications** ([table-09-p11-spec.csv](ad9081/tables/table-09-p11-spec.csv), p. 11)

| PARAMETER | CONDITIONS | MIN | MAX | UNITS |
|---|---|---|---|---|
| **MAXIMUM NUMERICALLY CONTROLLED OSCILLATOR (NCO) CLOCK RATE** |  |  |  |  |
| FDUC NCO |  |  | 1.5 | GHz |
| CDUC NCO |  |  | 12 | GHz |
| Fine Digital Downconverter (FDDC) NCO |  |  | 1.5 | GHz |
| Coarse Digital Downconverter (CDDC) NCO |  |  | 4 | GHz |
| **MAXIMUM NCO SHIFT FREQUENCY RANGE** |  |  |  |  |
| FDUC NCO | Channel interpolation rate must be > 1× | −750 | +750 | MHz |
| CDUC NCO | f_{DAC} = 12 GHz, main interpolation rate must be > 1× | −6 | +6 | GHz |
| FDDC NCO | Channel decimation rate must be > 1× | −750 | +750 | MHz |
| CDDC NCO | f_{ADC} = 4 GHz, main decimation rate must be > 1× | −2 | +2 | GHz |
| **MAXIMUM FREQUENCY SPACING BETWEEN CHANNELIZER CHANNELS** |  |  |  |  |
| Tx FDUC Channels | Maximum FDUC NCO clock rate × 0.8[^1] |  | 1200 | MHz |
| Rx FDDC Channels | Maximum FDDC NCO clock rate × 0.814[^2] |  | 1221 | MHz |

- **Note 1:** The 0.8 factor is because the total complex pass-band of the first interpolation filter is 80% of the filter input data rate.
- **Note 2:** The 0.814 factor is because the total complex pass-band of the decimation filter is 81.4% of the filter output data rate.

### JESD204B AND JESD204C INTERFACE ELECTRICAL AND SPEED SPECIFICATIONS

Nominal supplies. For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply, and for the typical values, T_{A} = 25°C, which corresponds to T_{J} = 80°C, unless otherwise noted.

**Table 11. Serial Interface Rate Specifications** ([table-10-p11-spec.csv](ad9081/tables/table-10-p11-spec.csv), p. 11)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| JESD204B SERIAL INTERFACE RATE | Serial lane rate | 1.0 |  | 15.5 | Gbps |
| Unit Interval |  | 64.5 |  | 1000.0 | ps |
| JESD204C SERIAL INTERFACE RATE | Serial lane rate | 6.0 |  | 24.75 | Gbps |
| Unit Interval |  | 40.4 |  | 166.67 | ps |

### Table 12. JESD204 Receiver (JRx) Electrical Specifications

**Table 12. JESD204 Receiver (JRx) Electrical Specifications** ([table-11-p11-spec.csv](ad9081/tables/table-11-p11-spec.csv), p. 11)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **JESD204 DATA INPUTS** | SERDINx±, where x = 0 to 7 |  |  |  |  |
| Standards Compliance |  |  | JESD204B and JESD204C |  |  |
| Differential Voltage, R_{VDIFF} |  |  | 800 |  | mV p-p |
| Differential Impedance, Z_{RDIFF} | At dc |  | 98 |  | Ω |
| Termination Voltage, V_{TT} | AC-coupled |  | 0.97 |  | V |
| **SYNCxOUTB± OUTPUTS[^1]** | Where x = 0 or 1 |  |  |  |  |
| Output Differential Voltage, V_{OD} | Driving 100 Ω differential load |  | 400 |  | mV |
| Output Offset Voltage, V_{OS} |  |  | DVDD1P8/2 + 0.2 |  | V |
| SYNCxOUTB+ AND SYNCxOUTB− | CMOS output option |  | Refer to the CMOS Pin Specifications section |  |  |

- **Note 1:** IEEE 1596.3 standard LVDS compatible.

### Table 13. JESD204 Transmitter (JTx) Electrical Specifications

**Table 13. JESD204 Transmitter (JTx) Electrical Specifications** ([table-12-p12-spec.csv](ad9081/tables/table-12-p12-spec.csv), p. 12)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **JESD204 DATA OUTPUTS** | SERDOUTx±, where x = 0 to 7 |  |  |  |  |
| Standards Compliance |  |  | JESD204B and JESD204C |  |  |
| Differential Output Voltage | Maximum strength |  | 675 |  | mV p-p |
| Differential Termination Impedance |  | 80 | 108 | 120 | Ω |
| Rise Time, t_{R} | 20% to 80% into 100 Ω load |  | 18 |  | ps |
| Fall Time, t_{F} | 20% to 80% into 100 Ω load |  | 18 |  | ps |
| **SYNCxINB± INPUTS[^1]** | Where x = 0 or 1 |  |  |  |  |
| Logic Compliance |  |  | LVDS |  |  |
| Differential Input Voltage |  | 0.24 | 0.7 | 1.9 | V p-p |
| Input Common-Mode Voltage | DC-coupled |  | 0.675 | 2 | V |
| Input Resistance, R_{IN} (Differential)[^2] |  |  | 18 |  | kΩ |
| Input Capacitance (Differential) |  |  | 1 |  | pF |
| SYNCxINB+ AND SYNCxINB− | CMOS input option |  | Refer to the CMOS Pin Specifications section |  |  |

- **Note 1:** IEEE 1596.3 standard LVDS compatible.
- **Note 2:** Available on-chip 100 Ω termination. See the UG-1578 user guide for details.

### Table 14. SYSREF Electrical Specifications

**Table 14. SYSREF Electrical Specifications** ([table-13-p12-spec.csv](ad9081/tables/table-13-p12-spec.csv), p. 12)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **SYSREFP AND SYSREFN INPUTS** |  |  |  |  |  |
| Logic Compliance |  |  | LVDS/LVPECL[^1] |  |  |
| Differential Input Voltage |  |  | 0.7 | 1.9 | V p-p |
| Input Common-Mode Voltage Range | DC-coupled |  | 0.675 | 2 | V |
| Input Resistance, R_{IN} (Differential) |  |  | 100 |  | Ω |
| Input Capacitance (Differential) |  |  | 1 |  | pF |

- **Note 1:** LVDS means low voltage differential signaling and LVPECL means low voltage positive/pseudo emitter-coupled logic.

### CMOS PIN SPECIFICATIONS

For the minimum and maximum values, T_{J} = -40°C to +120°C, 1.7 V ≤ DVDD1P8 ≤ 2.1 V, other supplies nominal, unless otherwise noted.

**Table 15. CMOS Pin Specifications** ([table-14-p13-spec.csv](ad9081/tables/table-14-p13-spec.csv), p. 13)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| **INPUTS** |  | SDIO, SCLK, CSB, RESETB, RXEN0, RXEN1, TXEN0, TXEN1, SYNC0INB±, SYNC1INB±, and GPIOx |  |  |  |  |
| Logic 1 Voltage | V_{IH} |  | 0.70 × DVDD1P8 |  |  | V |
| Logic 0 Voltage | V_{IL} |  |  |  | 0.3 × DVDD1P8 | V |
| Input Resistance |  |  | 40 |  |  | kΩ |
| **OUTPUTS** |  | SDIO, SDO, GPIOx, ADCx_FDx, ADCx_SMONx, SYNC0OUTB±, and SYNC1OUTB±, 4 mA load |  |  |  |  |
| Logic 1 Voltage | V_{OH} |  | DVDD1P8 − 0.45 |  |  | V |
| Logic 0 Voltage | V_{OL} |  |  |  | 0.45 | V |
| **INTERRUPT OUTPUTS** |  | IRQB_0 and IRQB_1, pull-up resistor of 5 kΩ to DVDD1P8 |  |  |  |  |
| Logic 1 Voltage | V_{OH} |  | 1.35 |  |  | V |
| Logic 0 Voltage | V_{OL} |  |  |  | 0.48 | V |

### DAC AC SPECIFICATIONS

Nominal supplies with T_{A} = 25°C. Specifications represent the average of all four DAC channels with the DAC I_{OUTFS} = 26 mA, unless otherwise noted.

**Table 16. DAC AC Specifications** ([table-15-p13-spec.csv](ad9081/tables/table-15-p13-spec.csv), p. 13)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| **SPURIOUS-FREE DYNAMIC RANGE (SFDR)** |  |  |  |  |  |
| **Single-Tone, f_{DAC} = 12 GSPS** | −7 dBFS digital backoff, shuffle enabled, 15C mode |  |  |  |  |
| Output Frequency (f_{OUT}) = 70 MHz |  | 63 | 80 |  | dBc |
| f_{OUT} = 100 MHz |  |  | 77 |  | dBc |
| f_{OUT} = 500 MHz |  |  | 76 |  | dBc |
| f_{OUT} = 900 MHz |  |  | 77 |  | dBc |
| f_{OUT} = 1900 MHz |  | 61 | 79 |  | dBc |
| f_{OUT} = 2600 MHz |  |  | 75 |  | dBc |
| f_{OUT} = 3700 MHz |  |  | 69 |  | dBc |
| f_{OUT} = 4500 MHz |  |  | 68 |  | dBc |
| **Single-Tone, f_{DAC} = 9 GSPS** | −7 dBFS digital backoff, shuffle enabled, 15C mode |  |  |  |  |
| f_{OUT} = 100 MHz |  |  | 78 |  | dBc |
| f_{OUT} = 500 MHz |  |  | 78 |  | dBc |
| f_{OUT} = 900 MHz |  |  | 77 |  | dBc |
| f_{OUT} = 1900 MHz |  |  | 80 |  | dBc |
| f_{OUT} = 2600 MHz |  |  | 80 |  | dBc |
| f_{OUT} = 3700 MHz |  |  | 72 |  | dBc |
| **Single-Tone, f_{DAC} = 6 GSPS** | −7 dBFS digital backoff, shuffle enabled, 15C mode |  |  |  |  |
| f_{OUT} = 100 MHz |  |  | 84 |  | dBc |
| f_{OUT} = 500 MHz |  |  | 81 |  | dBc |
| f_{OUT} = 900 MHz |  |  | 82 |  | dBc |
| f_{OUT} = 1900 MHz |  |  | 81 |  | dBc |
| **ADJACENT CHANNEL LEAKAGE RATIO** |  |  |  |  |  |
| **Single Carrier 20 MHz LTE Downlink Test Vector** | −1 dBFS digital backoff, 256 QAM |  |  |  |  |
| f_{DAC} = 12 GSPS | f_{OUT} = 1840 MHz |  | 77 |  | dBc |
| f_{DAC} = 12 GSPS | f_{OUT} = 2650 MHz |  | 76 |  | dBc |
|  | f_{OUT} = 3500 MHz |  | 73 |  | dBc |
| f_{DAC} = 9 GSPS | f_{OUT} = 1900 MHz |  | 77 |  | dBc |
|  | f_{OUT} = 2650 MHz |  | 77 |  | dBc |
| f_{DAC} = 6 GSPS | f_{OUT} = 750 MHz |  | 79 |  | dBc |
|  | f_{OUT} = 1840 MHz |  | 77 |  | dBc |
| **THIRD-ORDER INTERMODULATION DISTORTION (IMD3)** | Two tone test, 1 MHz spacing, 0 dBFS digital backoff, −6 dBFS per tone |  |  |  |  |
| f_{DAC} = 12 GSPS | f_{OUT} = 1900 MHz |  | −69 | −62 | dBc |
|  | f_{OUT} = 2600 MHz |  | −72 |  | dBc |
|  | f_{OUT} = 3700 MHz |  | −72 |  | dBc |
| f_{DAC} = 9 GSPS | f_{OUT} = 1900 MHz |  | −79 |  | dBc |
|  | f_{OUT} = 2600 MHz |  | −76 |  | dBc |
| f_{DAC} = 6 GSPS | f_{OUT} = 900 MHz |  | −79 |  | dBc |
|  | f_{OUT} = 1900 MHz |  | −90 |  | dBc |
| **NOISE SPECTRAL DENSITY (NSD)** | 0 dBFS, NSD measurement taken at 10% away from f_{OUT}, shuffle off |  |  |  |  |
| **Single-Tone, f_{DAC} = 12 GSPS** |  |  |  |  |  |
| f_{OUT} = 150 MHz |  |  | −168 |  | dBc/Hz |
| f_{OUT} = 500 MHz |  |  | −167 |  | dBc/Hz |
| f_{OUT} = 950 MHz |  |  | −165 |  | dBc/Hz |
| f_{OUT} = 1840 MHz |  |  | −162 |  | dBc/Hz |
| f_{OUT} = 2650 MHz |  |  | −160 |  | dBc/Hz |
| f_{OUT} = 3700 MHz |  |  | −155 |  | dBc/Hz |
| f_{OUT} = 4500 MHz |  |  | −154 |  | dBc/Hz |
| **Single-Tone, f_{DAC} = 9 GSPS** |  |  |  |  |  |
| f_{OUT} = 150 MHz |  |  | −168 |  | dBc/Hz |
| f_{OUT} = 500 MHz |  |  | −166 |  | dBc/Hz |
| f_{OUT} = 950 MHz |  |  | −164 |  | dBc/Hz |
| f_{OUT} = 1840 MHz |  |  | −160 |  | dBc/Hz |
| f_{OUT} = 2650 MHz |  |  | −158 |  | dBc/Hz |
| f_{OUT} = 3700 MHz |  |  | −154 |  | dBc/Hz |
| **Single-Tone, f_{DAC} = 6 GSPS** |  |  |  |  |  |
| f_{OUT} = 150 MHz |  |  | −168 |  | dBc/Hz |
| f_{OUT} = 500 MHz |  |  | −165 |  | dBc/Hz |
| f_{OUT} = 950 MHz |  |  | −163 |  | dBc/Hz |
| f_{OUT} = 1840 MHz |  |  | −159 |  | dBc/Hz |
| f_{OUT} = 2650 MHz |  |  | −157 |  | dBc/Hz |
| **SINGLE SIDEBAND PHASE NOISE OFFSET (PLL DISABLED)** | Direct device clock input at 6 dBm |  |  |  |  |
| f_{OUT} = 3.6 GHz, f_{DAC} = 12 GSPS, CLKINx Frequency (f_{CLKIN}) = 12 GHz | Rohde & Schwarz SMA100B B711 option |  |  |  |  |
| 1 kHz |  |  | −118 |  | dBc/Hz |
| 10 kHz |  |  | −129 |  | dBc/Hz |
| 100 kHz |  |  | −137 |  | dBc/Hz |
| 600 kHz |  |  | −144 |  | dBc/Hz |
| 1.2 MHz |  |  | −148 |  | dBc/Hz |
| 1.8 MHz |  |  | −149 |  | dBc/Hz |
| 6 MHz |  |  | −153 |  | dBc/Hz |
| **SINGLE SIDEBAND PHASE NOISE OFFSET (PLL ENABLED)** | Loop filter component values include C1 = 22 nF, R1 = 226 Ω, C2 = 2.2 nF, C3 = 33 nF, and PFD = 500 MHz[^1] |  |  |  |  |
| f_{OUT} = 1.8 GHz, f_{DAC} = 12 GSPS, f_{CLKIN} = 0.5 GHz |  |  |  |  |  |
| 1 kHz |  |  | −106 |  | dBc/Hz |
| 10 kHz |  |  | −113 |  | dBc/Hz |
| 100 kHz |  |  | −120 |  | dBc/Hz |
| 600 kHz |  |  | −127 |  | dBc/Hz |
| 1.2 MHz |  |  | −134 |  | dBc/Hz |
| 1.8 MHz |  |  | −138 |  | dBc/Hz |
| 6 MHz |  |  | −150 |  | dBc/Hz |

- **Note 1:** See UG-1578 for details on the loop filter components.

### ADC AC SPECIFICATIONS

Nominal supplies with T_{A} = 25°C. Input amplitude (A_{IN} ) = -1 dBFS, full bandwidth (no decimation) mode. For the minimum and maximum values, T_{J} = -40°C to +120°C. Specifications represent average of four ADC channels with DACs powered on. See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation , for definitions and for details on how these tests were completed.

**Table 17. ADC AC Specifications** ([table-16-p16-spec.csv](ad9081/tables/table-16-p16-spec.csv), p. 16)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| NOISE DENSITY[^1] | 3 GSPS |  | −150.3 |  | dBFS/Hz |
| NOISE DENSITY[^1] | 4 GSPS |  | −151.5 |  | dBFS/Hz |
| NOISE FIGURE[^2] | 3 GSPS |  | 28 |  | dB |
| NOISE FIGURE[^2] | 4 GSPS |  | 26.8 |  | dB |
| CODE ERROR RATE (CER) | 3 GSPS |  | < 1 × 10^{−30} |  | Errors |
| CODE ERROR RATE (CER) | 4 GSPS |  | 1 × 10^{−20} |  | Errors |
| **SIGNAL-TO-NOISE RATIO (SNR)** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | 57.8 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | 57.9 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | 57.7 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | 57.5 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | 56.9 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | 56.0 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | 55.9 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS | 52.4 | 54.5 |  | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | 55.1 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | 52.9 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | 53.9 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | 51.4 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | 53.2 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | 50.5 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | 52.3 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | 49.3 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | 51.3 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | 48.5 |  | dBFS |
| **SIGNAL-TO-NOISE-AND-DISTORTION (SINAD)** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | 57.5 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | 57.7 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | 57.2 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | 57.3 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | 56.1 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | 55.8 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | 54.5 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS | 51.0 | 54.2 |  | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | 53.2 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | 52.3 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | 48.4 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | 50.1 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | 47.8 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | 48.6 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | 46.1 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | 45.5 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | 44.8 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | 44.3 |  | dBFS |
| **EFFECTIVE NUMBER OF BITS (ENOB)** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | 9.3 |  | Bits |
| f_{IN} = 450 MHz | 4 GSPS |  | 9.3 |  | Bits |
| f_{IN} = 900 MHz | 3 GSPS |  | 9.2 |  | Bits |
| f_{IN} = 900 MHz | 4 GSPS |  | 9.2 |  | Bits |
| f_{IN} = 1800 MHz | 3 GSPS |  | 9.0 |  | Bits |
| f_{IN} = 1800 MHz | 4 GSPS |  | 9.0 |  | Bits |
| f_{IN} = 2700 MHz | 3 GSPS |  | 8.8 |  | Bits |
| f_{IN} = 2700 MHz | 4 GSPS | 8.2 | 8.7 |  | Bits |
| f_{IN} = 3600 MHz | 3 GSPS |  | 8.5 |  | Bits |
| f_{IN} = 3600 MHz | 4 GSPS |  | 8.4 |  | Bits |
| f_{IN} = 4500 MHz | 3 GSPS |  | 7.7 |  | Bits |
| f_{IN} = 4500 MHz | 4 GSPS |  | 8.0 |  | Bits |
| f_{IN} = 5400 MHz | 3 GSPS |  | 7.6 |  | Bits |
| f_{IN} = 5400 MHz | 4 GSPS |  | 7.8 |  | Bits |
| f_{IN} = 6300 MHz | 3 GSPS |  | 7.4 |  | Bits |
| f_{IN} = 6300 MHz | 4 GSPS |  | 7.3 |  | Bits |
| f_{IN} = 7200 MHz | 3 GSPS |  | 7.1 |  | Bits |
| f_{IN} = 7200 MHz | 4 GSPS |  | 7.1 |  | Bits |
| **SECOND-ORDER HARMONIC DISTORTION (HD2)** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | −73 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | −86 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | −76 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | −78 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | −71 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | −78 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | −65 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS |  | −67 | −53 | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | −61 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | −61 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | −55 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | −56 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | −50 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | −53 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | −48 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | −48 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | −46 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | −46 |  | dBFS |
| **THIRD-ORDER HARMONIC DISTORTION (HD3)** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | −76 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | −79 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | −76 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | −75 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | −76 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS |  | −73 | −66 | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | −71 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | −76 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | −62 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | −64 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | −60 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | −60 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | −59 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | −57 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | −58 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | −54 |  | dBFS |
| **WORST OTHER, EXCLUDING HD2, HD3, AND INTERLEAVING SPURS** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | −88 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | −87 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | −81 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS |  | −79 | −64 | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | −77 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | −77 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | −75 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | −74 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | −74 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | −72 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | −73 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | −72 |  | dBFS |
| **INTERLEAVING SPUR (f_{IN} ± f_{S}/2)[^3]** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | −97 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | −93 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | −94 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | −93 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | −96 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | −90 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | −86 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS |  | −86 |  | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | −84 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | −81 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | −53 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | −85 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | −86 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | −77 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | −79 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | −78 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | −74 |  | dBFS |
| **DIGITAL COUPLING SPUR (f_{IN} ± f_{S}/4)** |  |  |  |  |  |
| f_{IN} = 450 MHz | 3 GSPS |  | −83 |  | dBFS |
| f_{IN} = 450 MHz | 4 GSPS |  | −94 |  | dBFS |
| f_{IN} = 900 MHz | 3 GSPS |  | −79 |  | dBFS |
| f_{IN} = 900 MHz | 4 GSPS |  | −91 |  | dBFS |
| f_{IN} = 1800 MHz | 3 GSPS |  | −73 |  | dBFS |
| f_{IN} = 1800 MHz | 4 GSPS |  | −89 |  | dBFS |
| f_{IN} = 2700 MHz | 3 GSPS |  | −70 |  | dBFS |
| f_{IN} = 2700 MHz | 4 GSPS |  | −86 | −67 | dBFS |
| f_{IN} = 3600 MHz | 3 GSPS |  | −68 |  | dBFS |
| f_{IN} = 3600 MHz | 4 GSPS |  | −87 |  | dBFS |
| f_{IN} = 4500 MHz | 3 GSPS |  | −66 |  | dBFS |
| f_{IN} = 4500 MHz | 4 GSPS |  | −83 |  | dBFS |
| f_{IN} = 5400 MHz | 3 GSPS |  | −65 |  | dBFS |
| f_{IN} = 5400 MHz | 4 GSPS |  | −82 |  | dBFS |
| f_{IN} = 6300 MHz | 3 GSPS |  | −64 |  | dBFS |
| f_{IN} = 6300 MHz | 4 GSPS |  | −80 |  | dBFS |
| f_{IN} = 7200 MHz | 3 GSPS |  | −63 |  | dBFS |
| f_{IN} = 7200 MHz | 4 GSPS |  | −79 |  | dBFS |
| **TWO-TONE INTERMODULATION DISTORTION (IMD3, 2f_{IN1} − f_{IN2} OR 2f_{IN2} − f_{IN1} ) A_{IN1} AND A_{IN2} = −7 dBFS** |  |  |  |  |  |
| f_{IN1} = 1775 MHz, f_{IN2} = 1825 MHz | 3 GSPS |  | −81 |  | dBFS |
| f_{IN1} = 1775 MHz, f_{IN2} = 1825 MHz | 4 GSPS |  | −84 |  | dBFS |
| f_{IN1} = 2675 MHz, f_{IN2} = 2725 MHz | 3 GSPS |  | −77 |  | dBFS |
| f_{IN1} = 2675 MHz, f_{IN2} = 2725 MHz | 4 GSPS |  | −78 |  | dBFS |
| f_{IN1} = 3575 MHz, f_{IN2} = 3625 MHz | 3 GSPS |  | −73 |  | dBFS |
| f_{IN1} = 3575 MHz, f_{IN2} = 3625 MHz | 4 GSPS |  | −74 |  | dBFS |
| f_{IN1} = 5375 MHz, f_{IN2} = 5425 MHz | 3 GSPS |  | −66 |  | dBFS |
| f_{IN1} = 5375 MHz, f_{IN2} = 5425 MHz | 4 GSPS |  | −66 |  | dBFS |
| ANALOG BANDWIDTH[^4] | 3 GSPS |  | 7.5 |  | GHz |
| ANALOG BANDWIDTH[^4] | 4 GSPS |  | 7.5 |  | GHz |

- **Note 1:** Noise density is measured at 250 MHz input frequency at −30 dBFS, where timing jitter does not degrade noise floor.
- **Note 2:** Noise figure is based on a nominal full-scale input power of 4.5 dBm with an input span of 1.4 V p-p and R_{IN} = 100 Ω.
- **Note 3:** With background interleaving calibration converged.
- **Note 4:** Analog input bandwidth is the bandwidth of operation in which the full-scale input frequency response rolls off by −3 dB based on a de-embedded model of the ADC extracted from the measured frequency response on evaluation board. This bandwidth requires optimized matching network to achieve this upper bandwidth.

### TIMING SPECIFICATIONS

For the minimum and maximum values, T_{J} = -40°C to +120°C and ±5% of nominal supply, unless otherwise noted.

**Table 18. Timing Specifications** ([table-17-p19-spec.csv](ad9081/tables/table-17-p19-spec.csv), p. 19)

| PARAMETER | SYMBOL | CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| **SERIAL PORT INTERFACE (SPI) WRITE OPERATION** |  |  |  |  |  |  |
| Maximum SCLK Clock Rate | f_{SCLK}, 1/t_{SCLK} |  | 33 |  |  | MHz |
| SCLK Clock High | t_{PWH} | SCLK = 33 MHz | 8 |  |  | ns |
| SCLK Clock Low | t_{PWL} | SCLK = 33 MHz | 8 |  |  | ns |
| SDIO to SCLK Setup Time | t_{DS} |  | 4 |  |  | ns |
| SCLK to SDIO Hold Time | t_{DH} |  | 4 |  |  | ns |
| CSB to SCLK Setup Time | t_{S} |  | 4 |  |  | ns |
| CLK to CSB Hold Time | t_{H} |  | 4 |  |  | ns |
| **SPI READ OPERATION** |  |  |  |  |  |  |
| **LSB First Data Format** |  |  |  |  |  |  |
| Maximum SCLK Clock Rate | f_{SCLK}, 1/t_{SCLK} |  | 33 |  |  | MHz |
| SCLK Clock High | t_{PWH} |  | 8 |  |  | ns |
| SCLK Clock Low | t_{PWL} |  | 8 |  |  | ns |
| **MSB First Data Format** |  |  |  |  |  |  |
| Maximum SCLK Clock Rate | f_{SCLK}, 1/t_{SCLK} |  | 15 |  |  | MHz |
| SCLK Clock High | t_{PWH} |  | 30 |  |  | ns |
| SCLK Clock Low | t_{PWL} |  | 30 |  |  | ns |
| SDIO to SCLK Setup Time | t_{DS} |  | 4 |  |  | ns |
| SCLK to SDIO Hold Time | t_{DH} |  | 4 |  |  | ns |
| CSB to SCLK Setup Time | t_{S} |  | 4 |  |  | ns |
| SCLK to SDIO Data Valid Time | t_{DV} |  | 20 |  |  | ns |
| SCLK to SDO Data Valid Time | t_{DV_SDO} |  | 20 |  |  | ns |
| CSB to SDIO Output Valid to High-Z | t_{Z} |  | 20 |  |  | ns |
| CSB to SDO Output Valid to High-Z | t_{Z_SDO} |  | 20 |  |  | ns |
| RESETB |  | Minimum hold time to trigger a device reset | 40 |  |  | ns |

### Timing Diagrams

![Figure 2. Timing Diagram for 3-Wire Write Operation](ad9081/figures/ad9081-f002.png)

*Figure 2. Timing Diagram for 3-Wire Write Operation*

![Figure 3. Timing Diagram for 3-Wire Read Operation](ad9081/figures/ad9081-f102.png)

*Figure 3. Timing Diagram for 3-Wire Read Operation*

![Figure 4. Timing Diagram for 4-Wire Read Operation](ad9081/figures/ad9081-f003.png)

*Figure 4. Timing Diagram for 4-Wire Read Operation*

### ABSOLUTE MAXIMUM RATINGS

**Table 19.** ([table-18-p21-abs_max.csv](ad9081/tables/table-18-p21-abs_max.csv), p. 21)

| PARAMETER | RATING |
|---|---|
| ISET, DACxP, DACxN, TDP, TDN | −0.3 V to AVDD2 + 0.3 V |
| VCO_COARSE, VCO_FINE, VCO_VCM, VCO_VREG | −0.3 V to AVDD2_PLL + 0.3 V |
| Rx Input Power (ADC0P/N, ADC1P/N, ADC2P/N, ADC3P/N)[^1] | 22 dBm |
| VCM0, VCM1 | −0.3 V to RVDD2 + 0.3 V |
| CLKINP, CLKINN | −0.2 V to PLLCLKVDD1 + 0.2 V |
| ADCDRVN, ADCDRVP | −0.2 V to CLKVDD1 + 0.2 V |
| SERDINx±, SERDOUTx± | −0.2 V to SVDD1 + 0.2 V |
| SYSREFP, SYSREFN, and SYNCxINB± | −0.2 V to +2.5 V |
| SYNCxOUTB±, SYNCxINB±, RESETB, TXENx, RXENx, IRQB_x, CSB, SCLK, SDIO, SDO, TMU_REFN, TMU_REFP, ADCx_SMON0, ADCx_SMON1, ADCx_FD0, ADCx_FD1, GPIOx | −0.3 V to DVDD1P8 + 0.3 V |
| AVDD2, AVDD2_PLL, BVDD2, RVDD2, SVDD2_PLL, DVDD1P8 | −0.3 V to +2.2 V |
| PLLCLKVDD1, AVDD1, AVDD1_ADC, CLKVDD1, FVDD1, DAVDD1, DVDD1_RT, DCLKVDD1, SVDD1, SVDD1_PLL | −0.2 V to +1.2 V |
| VNN1 | −1.1 V to +0.2 V |
| **Temperature Ranges** |  |
| Maximum Junction (T_{J})[^2] | 120°C |
| Storage | −65°C to +150°C |

- **Note 1:** Tested continuously for 1000 hours with f_{IN} = 4.7 GHz pulsed and continuous tone at maximum allowed junction temperature (T_{J}). Refer to the UG-1578 user guide for more information.
- **Note 2:** Do not exceed this temperature for any duration of time when the device is powered.

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

### THERMAL RESISTANCE

Thermal performance is directly linked to PCB design and operating environment. The use of appropriate thermal management techniques is recommended to ensure that the maximum T_{J} does not exceed the limits shown in Table 19.

θ_{JA} is the natural convection, junction to ambient thermal resistance measured in a one cubic foot sealed enclosure.

θ_{JC_TOP} is the junction to case, thermal resistance.

θ_{JB} is the junction to board, thermal resistance.

### Table 20. Simulated Thermal Resistance[^1]

**Table 20. Simulated Thermal Resistance[^1]** ([table-19-p21-data.csv](ad9081/tables/table-19-p21-data.csv), p. 21)

| PCB Type | Airflow Velocity (m/sec) | θ_{JA} | θ_{JC_TOP} | θ_{JB} | Unit |
|---|---|---|---|---|---|
| JEDEC 2s2p Board | 0.0 | 14.9 | 0.70 | 1.8 | °C/W |

- **Note 1:** Thermal resistance values specified are simulated based on JEDEC specifications in compliance with JESD51-12 with the device power equal to 9 W.

### ESD CAUTION

ESD (electrostatic discharge) sensitive device . Charged devi ces and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

### PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

![Figure 5. Pin Configuration](ad9081/figures/ad9081-f005.png)

*Figure 5. Pin Configuration*

**Table 21. Pin Function Descriptions** ([table-20-p22-pin.csv](ad9081/tables/table-20-p22-pin.csv), p. 22)

| Pin No. | Mnemonic | Type | Description |
|---|---|---|---|
| **POWER SUPPLIES** |  |  |  |
| A2, E2, H2, L2, P2, V2 | AVDD2 | Input | Analog 2.0 V Supply Inputs for DAC. |
| L3 | AVDD2_PLL | Input | Analog 2.0 V Supply Input for Clock PLL Linear Dropout Regulator (LDO). |
| D7, E7, P7, R7 | BVDD2 | Input | Analog 2.0 V Supply Inputs for ADC Buffer. |
| B11, U11 | RVDD2 | Input | Analog 2.0 V Supply Inputs for ADC Reference. |
| J5 | PLLCLKVDD1 | Input | Analog 1.0 V Supply Input for Clock PLL. |
| D2, D3, D4, E3, F3, N3, P3, R2, R3, R4 | AVDD1 | Input | Analog 1.0 V Supply Inputs for DAC Clock. |
| G7, G8, M7, M8 | AVDD1_ADC | Input | Analog 1.0 V Supply Inputs for ADC. |
| G6, M6 | CLKVDD1 | Input | Analog 1.0 V Supply Inputs for ADC Clock. |
| D6, R6 | FVDD1 | Input | Analog 1.0 V Supply Inputs for ADC Reference. |
| D10, R10 | VDD1_NVG | Input | Analog 1.0 V Supply Inputs for Negative Voltage Generator (NVG) Used to Generate −1 V Output. |
| E9, P9 | NVG1_OUT | Output | Analog −1 V Supply Outputs from NVG. Decouple NVG1_OUT to GND with a 0.1 µF capacitor. |
| D8, E8, E10, P8, R8, P10 | VNN1 | Input | Analog −1 V Supply Inputs for ADC Buffer and Reference. Connect these pins to the adjacent NVG1_OUT pins. |
| C9, T9 | BVNN2 | Output | Decoupling Pin for the Internally Generated Analog −2 V ADC Buffer Supply. Decouple each BVNN2 pin to GND with a 0.1 µF capacitor. |
| C10, T10 | BVDD3 | Output | Decoupling Pin for the Internally Generated Analog 3 V ADC Buffer Supply. Decouple BVDD3 to GND with 0.1 µF capacitor. |
| E5, F5, N5, P5 | DAVDD1 | Input | Digital Analog 1.0 V Supply Inputs. |
| F10, H9, H11, J9, J11, K9, K11, L9, L11, M9 | DVDD1 | Input | Digital 1.0 V Supply Inputs. |
| J7, K7 | DVDD1_RT | Input | Digital 1.0 V Supply Inputs for Retimer Block. |
| K5 | DCLKVDD1 | Input | Digital 1.0 V Clock Generation Supply. |
| A16, B16, C16, D16, E16, F16, G16, H16, M16, N16, P16, R16, T16, U16, V16 | SVDD1 | Input | Digital 1.0 V Supply Inputs for SERDES Deserializer and Serializer. |
| K15 | SVDD2_PLL | Input | Digital 2.0 V Supply Input for SERDES LDO. |
| J16, K16 | SVDD1_PLL | Input | Digital 1.0 V Supply Inputs for SERDES Clock Generation and PLL. |
| C13, F9, T13 | DVDD1P8 | Input | Digital Interface and Temperature Monitoring Unit (TMU) Supply Inputs (Nominal 1.8 V). |
| A1, A3, A4, A7, A8, A11, A17, A18, B2 to B6, B9, B10, B14, B15, C2, C5 to C8, C11, C17, C18, D1, D5, D9, D14, D15, E1, E4, E6, E17, E18, F2, F4, F6 to F8, F14, F15, G2 to G5, G17, G18, H1, H5 to H8, H10, H12, H14, H15, J2, J8, J10, J12, J14, J15, J17, J18, K2, K8, K10, K12, K14, K17, K18, L1, L5 to L8, L10, L12, L14, M2 to M5, M10, M17, M18, N2, N4, N6 to N8, N14, N15, P1, P4, P6, P17, P18, R1, R5, R9, R14, R15, T2, T5 to T8, T11, T17, T18, U2 to U6, U9, U10, U14, U15, V1, V3, V4, V7, V8, V11, V17, V18 | GND | Input/output | Ground References. |
| **ANALOG OUTPUTS** |  |  |  |
| B1, C1 | DAC0P, DAC0N | Output | DAC0 Output Currents, Ground Referenced. Tie these pins to GND if unused. |
| G1, F1 | DAC1P, DAC1N | Output | DAC1 Output Currents, Ground Referenced. Tie these pins to GND if unused. |
| M1, N1 | DAC2P, DAC2N | Output | DAC2 Output Currents, Ground Referenced. Tie these pins to GND if unused. |
| U1, T1 | DAC3P, DAC3N | Output | DAC3 Output Currents, Ground Referenced. Tie these pins to GND if unused. |
| H3 | ISET | Output | DAC Bias Current Setting Pin. Connect this pin with a 5 kΩ resistor to GND. |
| C4, C3 | ADCDRVP, ADCDRVN | Output | Optional Clock Output (for example, ADC Clock Driver for an external ADC). These pins are disabled by default. Leave the pins floating if unused. |
| B7, U7, B8, U8 | VCM0, VCM1, VCM2, VCM3 | Output | ADC Buffer Common-Mode Output Voltage. Decouple these pins to GND with a 0.1 µF capacitor. |
| K3 | VCO_VREG | Output | PLL LDO Regulator Output. Decouple this pin to GND with a 2.2 µF capacitor. |
| G9 | TMU_REFN | Output | TMU ADC Negative Reference. Connect this pin to GND. |
| G10 | TMU_REFP | Output | TMU ADC Positive Reference. Connect this pin to DVDD1P8. |
| **ANALOG INPUTS** |  |  |  |
| A6, A5 | ADC0P, ADC0N | Input | ADC0 Differential Inputs with Internal 100 Ω Differential Resistor. Leave these pins floating if unused. |
| V6, V5 | ADC1P, ADC1N | Input | ADC1 Differential Inputs with Internal 100 Ω Differential Resistor. Leave these pins floating if unused. |
| A10, A9 | ADC2P, ADC2N | Input | ADC2 Differential Inputs with Internal 100 Ω Differential Resistor. Leave these pins floating if unused. |
| V10, V9 | ADC3P, ADC3N | Input | ADC3 Differential Inputs with Internal 100 Ω Differential Resistor. Leave these pins floating if unused. |
| J3 | VCO_FINE | Input | On-Chip Device Clock Multiplier and PLL Fine Loop Filter Input. If the PLL is not in use, leave this pin floating and disable the PLL via the control registers. |
| J4 | VCO_COARSE | Input | On-Chip Device Clock Multiplier and PLL Coarse Loop Filter Input. If the PLL is not in use, leave this pin floating and disable the PLL via the control registers. |
| K4 | VCO_VCM | Input | On-Chip Device Clock Multiplier and VCO Common-Mode Input. If the PLL is not in use, leave this pin floating and disable the PLL via the control registers. |
| N9, N10 | TDP, TDN | Input | Anode and Cathode of Temperature Diodes. This feature is not supported. Tie TDP and TDN to GND. |
| J1, K1 | CLKINP, CLKINN | Input | Differential Clock Inputs with Nominal 100 Ω Termination. Self bias input requiring ac coupling. When the on-chip clock multiplier PLL is enabled, this input is the reference clock input. If the PLL is disabled, an RF clock equal to the DAC output sample rate is required. |
| **CMOS INPUTS AND OUTPUTS[^1]** |  |  |  |
| G13 | CSB | Input | Serial Port Enable Input. Active low. |
| H13 | SCLK | Input | Serial Plot Clock Input. |
| F13 | SDIO | Input/output | Serial Port Bidirectional Data Input/Output. |
| J13 | SDO | Output | Serial Port Data Output. |
| C12 | RESETB | Input | Active Low Reset Input. RESETB places digital logic and SPI registers in a known default state. RESETB must be connected to a digital IC that is capable of issuing a reset signal for the first step in the device initialization process. |
| E13, D13 | RXEN0, RXEN1 | Input | Active High ADC and Receive Datapath Enable Inputs. RXENx is also SPI configurable. |
| P13, R13 | TXEN0, TXEN1 | Input | Active High DAC and Transmit Datapath Enable Inputs. TXENx is also SPI configurable. |
| D12, D11 | ADC0_FD0, ADC0_FD1 | Output | ADC0 Fast Detect Outputs by Default. Do not connect if unused. |
| E12, E11 | ADC1_FD0, ADC1_FD1 | Output | ADC1 Fast Detect Outputs by Default. Do not connect if unused. |
| F12, F11 | ADC2_FD0, ADC2_FD1 | Output | ADC2 Fast Detect Outputs by Default. Do not connect if unused. |
| G12, G11 | ADC3_FD0, ADC3_FD1 | Output | ADC3 Fast Detect Outputs by Default. Do not connect if unused. |
| P12, R12 | IRQB_0, IRQB_1 | Output | Interrupt Request Outputs. These pins are open-drain, active low outputs (CMOS levels with respect to DVDD1P8). Connect a > 5 kΩ pull-up resistor to DVDD1P8 to prevent these pins from floating when unused. |
| M11, M12, N11, N12, P11, R11 | GPIO0 to GPIO5 | Input/output | General-Purpose Input or Output Pins. These pins control auxiliary functions related to the Tx datapaths. |
| K13, L13, M13, N13, T12 | GPIO6 to GPIO10 | Input/output | General-Purpose Input or Output Pins. These pins control auxiliary functions related to the Rx datapaths and ADCs. |
| **JESD204B or JESD204C COMPATIBLE SERDES DATA LANES AND CONTROL SIGNALS[^2]** |  |  |  |
| L18, L17 | SERDIN0+, SERDIN0− | Input | JRx Lane 0 Inputs, Data True/Complement. |
| N18, N17 | SERDIN1+, SERDIN1− | Input | JRx Lane 1 Inputs, Data True/Complement. |
| R18, R17 | SERDIN2+, SERDIN2− | Input | JRx Lane 2 Inputs, Data True/Complement. |
| U18, U17 | SERDIN3+, SERDIN3− | Input | JRx Lane 3 Inputs, Data True/Complement. |
| M15, M14 | SERDIN4+, SERDIN4− | Input | JRx Lane 4 Inputs, Data True/Complement. |
| V15, V14 | SERDIN5+, SERDIN5− | Input | JRx Lane 5 Inputs, Data True/Complement. |
| T15, T14 | SERDIN6+, SERDIN6− | Input | JRx Lane 6 Inputs, Data True/Complement. |
| P15, P14 | SERDIN7+, SERDIN7− | Input | JRx Lane 7 Inputs, Data True/Complement. |
| U13, V13 | SYNC0OUTB+, SYNC0OUTB− | Output | JRx Link 0 Synchronization Outputs for the JESD204B Interface. These pins are LVDS or CMOS configurable. These pins can also provide differential 100 Ω output impedance in LVDS mode. |
| U12, V12 | SYNC1OUTB+, SYNC1OUTB− | Output | JRx Link 1 Synchronization Outputs for the JESD204B interface or CMOS Input to Control the Transmit Fast Frequency Hopping (FFH) Feature. For JRx link synchronization, these pins can be configured as LVDS or CMOS outputs and can provide differential 100 Ω output impedance in LVDS mode. |
| A15, A14 | SERDOUT0+, SERDOUT0− | Output | JTx Lane 0 Outputs, Data True/Complement. |
| C15, C14 | SERDOUT1+, SERDOUT1− | Output | JTx Lane 1 Outputs, Data True/Complement. |
| E15, E14 | SERDOUT2+, SERDOUT2− | Output | JTx Lane 2 Outputs, Data True/Complement. |
| G15, G14 | SERDOUT3+, SERDOUT3− | Output | JTx Lane 3 Outputs, Data True/Complement. |
| H18, H17 | SERDOUT4+, SERDOUT4− | Output | JTx Lane 4 Outputs, Data True/Complement. |
| F18, F17 | SERDOUT5+, SERDOUT5− | Output | JTx Lane 5 Outputs, Data True/Complement. |
| D18, D17 | SERDOUT6+, SERDOUT6− | Output | JTx Lane 6 Outputs, Data True/Complement. |
| B18, B17 | SERDOUT7+, SERDOUT7− | Output | JTx Lane 7 Outputs, Data True/Complement. |
| B13, A13 | SYNC0INB+, SYNC0INB− | Input | JTx Link 0 Synchronization Inputs for the JESD204B Interface. These pins are LVDS or CMOS configurable. These pins are LVDS or CMOS configurable and have selectable internal 100 Ω input impedance for LVDS operation |
| B12, A12 | SYNC1INB+, SYNC1INB− | Input | JTx Link 1 Synchronization Inputs for the JESD204B Interface or CMOS Inputs for Receive FFH via the GPIOx Pins. These pins are LVDS or CMOS configurable and have selectable internal 100 Ω input impedance for LVDS operation. |
| T4, T3 | SYSREFP, SYSREFN | Input | Active High JESD204B/C System Reference Inputs. These pins are configurable for differential current mode logic (CML), PECL, and LVDS with internal 100 Ω termination or single-ended CMOS. |
| **NO CONNECTS AND DO NOT CONNECTS** |  |  |  |
| J6, K6 | NC |  | No Connect. These pins can be left open or connected. |
| H4, L4, L15, L16 | DNC | DNC | Do Not Connect. The pins must be kept open. |

- **Note 1:** CMOS inputs do not have pull-up or pull-down resistors.
- **Note 2:** SERDINx± and SERDOUTx± include 100 Ω internal termination resistors.

### TYPICAL PERFORMANCE CHARACTERISTICS

### DAC

The data curves represent the average performance across all outputs with harmonics and spurs falling in the first Nyquist zone (&lt;f_{DAC} /2). All SFDR, IMD3, and NSD data measured on a laboratory evaluation board. All data for the phase noise and adjacent channel leakage ratio (ACLR) is measured on the AD9081-FMCA-EBZ customer evaluation board. For additional information on the JESD204B and JESD204C mode configurations, see the UG-1578 user guide.

![Figure 6. HD2 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C](ad9081/figures/ad9081-f006.png)

*Figure 6. HD2 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C*

Digitized data: [hd2-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-interpolation-1-m.csv](ad9081/curves/hd2-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-interpolation-1-m.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 7. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C](ad9081/figures/ad9081-f007.png)

*Figure 7. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C*

Digitized data: [hd2-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv](ad9081/curves/hd2-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 8. HD3 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C](ad9081/figures/ad9081-f008.png)

*Figure 8. HD3 vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C*

Digitized data: [hd3-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-interpolation-1-m.csv](ad9081/curves/hd3-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-interpolation-1-m.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 9. HD2 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C](ad9081/figures/ad9081-f009.png)

*Figure 9. HD2 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C*

Digitized data: [hd2-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv](ad9081/curves/hd2-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 10. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B](ad9081/figures/ad9081-f010.png)

*Figure 10. HD2 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B*

Digitized data: [hd2-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv](ad9081/curves/hd2-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 11. HD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C](ad9081/figures/ad9081-f011.png)

*Figure 11. HD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C*

Digitized data: [hd3-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv](ad9081/curves/hd3-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 12. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C](ad9081/figures/ad9081-f012.png)

*Figure 12. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C*

Digitized data: [hd3-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv](ad9081/curves/hd3-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 13. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C](ad9081/figures/ad9081-f013.png)

*Figure 13. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C*

Digitized data: [sfdr-worst-spurious-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-i.csv](ad9081/curves/sfdr-worst-spurious-vs-f-out-over-digital-scale-6-gsps-dac-sample-rate-channel-i.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 14. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C](ad9081/figures/ad9081-f014.png)

*Figure 14. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C*

![Figure 15. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B](ad9081/figures/ad9081-f015.png)

*Figure 15. HD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B*

Digitized data: [hd3-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv](ad9081/curves/hd3-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 16. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C](ad9081/figures/ad9081-f016.png)

*Figure 16. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C*

Digitized data: [sfdr-worst-spurious-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-i.csv](ad9081/curves/sfdr-worst-spurious-vs-f-out-over-digital-scale-9-gsps-dac-sample-rate-channel-i.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 17. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B](ad9081/figures/ad9081-f017.png)

*Figure 17. SFDR, Worst Spurious vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B*

Digitized data: [sfdr-worst-spurious-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-.csv](ad9081/curves/sfdr-worst-spurious-vs-f-out-over-digital-scale-12-gsps-dac-sample-rate-channel-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 18. IMD3 vs. f_{OUT} over Digital Scale (Mode 17B), 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C,](ad9081/figures/ad9081-f018.png)

*Figure 18. IMD3 vs. f_{OUT} over Digital Scale (Mode 17B), 6 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 4×, Mode 15C, IMD3 is a Two-Tone Test, and the Scale per Tone is 6 dB Lower than the
Reported Digital Scale*

Digitized data: [imd3-vs-fout-over-digital-scale-mode-17b-6-gsps-dac-sample-rate-channel-interpol.csv](ad9081/curves/imd3-vs-fout-over-digital-scale-mode-17b-6-gsps-dac-sample-rate-channel-interpol.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 19. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital](ad9081/figures/ad9081-f019.png)

*Figure 19. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 8×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital Scale*

Digitized data: [imd3-vs-fout-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv](ad9081/curves/imd3-vs-fout-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-1-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 20. IMD3 vs. f_{OUT} over f_{DAC} , Digital Scale -7 dBFS, IMD3 is a Two-Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital Scale](ad9081/figures/ad9081-f020.png)

*Figure 20. IMD3 vs. f_{OUT} over f_{DAC} , Digital Scale -7 dBFS, IMD3 is a Two-Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital Scale*

Digitized data: [imd3-vs-f-out-over-f-dac-digital-scale-7-dbfs-imd3-is-a-two-tone-test-and-the-sc.csv](ad9081/curves/imd3-vs-f-out-over-f-dac-digital-scale-7-dbfs-imd3-is-a-two-tone-test-and-the-sc.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 21. IMD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital](ad9081/figures/ad9081-f021.png)

*Figure 21. IMD3 vs. f_{OUT} over Digital Scale, 9 GSPS DAC Sample Rate, Channel Interpolation 1×, Main Interpolation 6×, Mode 15C, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital*

Digitized data: [imd3-vs-fout-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv](ad9081/curves/imd3-vs-fout-over-digital-scale-9-gsps-dac-sample-rate-channel-interpolation-1-m.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 22. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital](ad9081/figures/ad9081-f022.png)

*Figure 22. IMD3 vs. f_{OUT} over Digital Scale, 12 GSPS DAC Sample Rate, Channel Interpolation 4×, Main Interpolation 8×, Mode 16B, IMD3 is a Two- Tone Test, and the Scale per Tone is 6 dB Lower than the Reported Digital Scale*

Digitized data: [imd3-vs-fout-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv](ad9081/curves/imd3-vs-fout-over-digital-scale-12-gsps-dac-sample-rate-channel-interpolation-4-.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 23. SFDR, Worst In-Band Spurious vs. f_{OUT} over f_{DAC} , with 0 dBFS Tone Level](ad9081/figures/ad9081-f023.png)

*Figure 23. SFDR, Worst In-Band Spurious vs. f_{OUT} over f_{DAC} , with 0 dBFS Tone Level*

Digitized data: [sfdr-worst-in-band-spurious-vs-f-out-over-f-dac-with-0-dbfs-tone-level.csv](ad9081/curves/sfdr-worst-in-band-spurious-vs-f-out-over-f-dac-with-0-dbfs-tone-level.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 24. DAC0 Fundamental Output Power vs. f_{OUT} Across f_{DAC}, at 0 dBFS](ad9081/figures/ad9081-f024.png)

*Figure 24. DAC0 Fundamental Output Power vs. f_{OUT} Across f_{DAC}, at 0 dBFS Digital Backoff, Measured on a Laboratory Evaluation Board, the AD9081-FMCA-EBZ Evaluation Board has a Different PCB Layout and Results in a Different Frequency Response when Compared to a Laboratory Evaluation
Board*

Digitized data: [dac0-fundamental-output-power-vs-fout-across-fdac-at-0-dbfs.csv](ad9081/curves/dac0-fundamental-output-power-vs-fout-across-fdac-at-0-dbfs.csv) (x: MHz; y: dBm) — values read off the printed plot by the digitizer, not published data.

![Figure 25. Single Sideband Phase Noise vs. Frequency Offset for Different Clock Input Power (P_{CLK} ), f_{OUT} = 1.8 GHz, External 12 GHz Clock Input with Clock PLL Disabled](ad9081/figures/ad9081-f025.png)

*Figure 25. Single Sideband Phase Noise vs. Frequency Offset for Different Clock Input Power (P_{CLK} ), f_{OUT} = 1.8 GHz, External 12 GHz Clock Input with Clock PLL Disabled*

Digitized data: [single-sideband-phase-noise-vs-frequency-offset-for-different-clock-input-power-.csv](ad9081/curves/single-sideband-phase-noise-vs-frequency-offset-for-different-clock-input-power-.csv) (x: Hz; y: dBc/Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 26. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , Shuffle On, 16-Bit Resolution, Mode 15C](ad9081/figures/ad9081-f026.png)

*Figure 26. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , Shuffle On, 16-Bit Resolution, Mode 15C*

Digitized data: [single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-over-f-dac-shuffle-on-.csv](ad9081/curves/single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-over-f-dac-shuffle-on-.csv) (x: MHz; y: dBc/Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 27. Single Sideband Phase Noise vs. Frequency Offset for Different](ad9081/figures/ad9081-f027.png)

*Figure 27. Single Sideband Phase Noise vs. Frequency Offset for Different PLL Reference Clocks (f_{REF}), f_{OUT} = 1.8 GHz, f_{DAC} = 12 GSPS, PLL Enabled
with Exception of External 12 GHz Clock Input with Clock PLL Disabled*

Digitized data: [single-sideband-phase-noise-vs-frequency-offset-for-different.csv](ad9081/curves/single-sideband-phase-noise-vs-frequency-offset-for-different.csv) (x: Hz; y: dBc/Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 28. Single Sideband Phase Noise vs. Frequency Offset for Different DAC Output Frequencies (f_{OUT} ), External 12 GHz Clock Input with Clock PLL Disabled](ad9081/figures/ad9081-f028.png)

*Figure 28. Single Sideband Phase Noise vs. Frequency Offset for Different DAC Output Frequencies (f_{OUT} ), External 12 GHz Clock Input with Clock PLL Disabled*

Digitized data: [single-sideband-phase-noise-vs-frequency-offset-for-different-dac-output-frequen.csv](ad9081/curves/single-sideband-phase-noise-vs-frequency-offset-for-different-dac-output-frequen.csv) (x: Hz; y: dBc/Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 29. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , 12-Bit Resolution, Shuffle On, Mode 24C](ad9081/figures/ad9081-f029.png)

*Figure 29. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} over f_{DAC} , 12-Bit Resolution, Shuffle On, Mode 24C*

Digitized data: [single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-over-f-dac-12-bit-reso.csv](ad9081/curves/single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-over-f-dac-12-bit-reso.csv) (x: MHz; y: dBc/Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 30. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 16-Bit Resolution, Mode 15C](ad9081/figures/ad9081-f030.png)

*Figure 30. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 16-Bit Resolution, Mode 15C*

![Figure 31. Dual Band ACLR Performance for Two 20 MHz LTE carriers at f_{OUT}](ad9081/figures/ad9081-f031.png)

*Figure 31. Dual Band ACLR Performance for Two 20 MHz LTE carriers at f_{OUT} = 1.88 GHz and f_{OUT} = 2.145 GHz (Refer to Figure 32 for a Wideband Plot), Showing a Close Up of One Carrier at f_{OUT} = 1.88 GHz, f_{DAC} = 11.796 GSPS, Test Vector PAR = 7.7 dB with −1 dBFS Backoff, Channel Interpolation 3×, Main Interpolation 8×, Mode 9C*

![Figure 32. Dual Band Wideband Plot for Two 20 MHz LTE Carriers at f_{OUT} = 1.88 GHz and f_{OUT} = 2.145 GHz (3GPP Bands, B1 and B3, Respectively),](ad9081/figures/ad9081-f032.png)

*Figure 32. Dual Band Wideband Plot for Two 20 MHz LTE Carriers at f_{OUT} = 1.88 GHz and f_{OUT} = 2.145 GHz (3GPP Bands, B1 and B3, Respectively), at f_{DAC} = 11.796 GSPS, Test Vector PAR = 7.7 dB with −1 dBFS Backoff ,
Channel Interpolation 3×, Main Interpolation 8×, Mode 9C*

![Figure 33. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 12-Bit Resolution, Mode 24C](ad9081/figures/ad9081-f033.png)

*Figure 33. Single-Tone NSD Measured at 10% Offset from f_{OUT} vs. f_{OUT} , Shuffle Off vs. Shuffle On, f_{DAC} = 11796.48 MSPS, 12-Bit Resolution, Mode 24C*

Digitized data: [single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-shuffle-off-vs-shuffle.csv](ad9081/curves/single-tone-nsd-measured-at-10-offset-from-f-out-vs-f-out-shuffle-off-vs-shuffle.csv) (x: MHz; y: dBc/Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 34. Dual Band ACLR Performance for two 20 MHz LTE carriers at f_{OUT}](ad9081/figures/ad9081-f034.png)

*Figure 34. Dual Band ACLR Performance for two 20 MHz LTE carriers at f_{OUT} = 1.88 GHz and fOUT = 2.145 GHz (Refer to Figure 32 for a Wideband Plot), Showing a Close-up of One Carrier at f_{OUT} = 2.145 GHz, f_{DAC} = 11.796 GSPS, Test Vector PAR = 7.7 dB with −1 dBFS Backoff, Channel Interpolation 3×, Main Interpolation 8×, Mode 9C*

![Figure 35. ACLR Performance for 100 MHz 5G Test Vector at f_{OUT} = 3.9 GHz](ad9081/figures/ad9081-f035.png)

*Figure 35. ACLR Performance for 100 MHz 5G Test Vector at f_{OUT} = 3.9 GHz and f_{DAC} = 11.898 GSPS, Test Vector Peak to RMS = 11.7 dB with −1 dBFS
Backoff (Mode 9C), Channel Interpolation 3×, Main Interpolation 8×*

### ADC: 4 GSPS

Nominal supplies, sampling rate = 4 GSPS with DAC clock frequency (f_{CLK} ) = 12 GHz direct RF clock, full bandwidth mode operation (no decimation), T_{J} = 80°C (T_{A} = 25°C), 128k FFT sample with five averages, and A_{IN} = -1 dBFS, unless otherwise noted.

![Figure 36. Single-Tone FFT at f_{IN} = 450 MHz](ad9081/figures/ad9081-f036.png)

*Figure 36. Single-Tone FFT at f_{IN} = 450 MHz*

![Figure 37. Single-Tone FFT at f_{IN} = 900 MHz](ad9081/figures/ad9081-f037.png)

*Figure 37. Single-Tone FFT at f_{IN} = 900 MHz*

![Figure 38. Single-Tone FFT at f_{IN} = 1800 MHz](ad9081/figures/ad9081-f038.png)

*Figure 38. Single-Tone FFT at f_{IN} = 1800 MHz*

![Figure 39. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz](ad9081/figures/ad9081-f039.png)

*Figure 39. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-450-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-450-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 40. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz](ad9081/figures/ad9081-f040.png)

*Figure 40. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz*

![Figure 41. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz](ad9081/figures/ad9081-f041.png)

*Figure 41. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz*

![Figure 42. Single-Tone FFT at f_{IN} = 2700 MHz](ad9081/figures/ad9081-f042.png)

*Figure 42. Single-Tone FFT at f_{IN} = 2700 MHz*

![Figure 43. Single-Tone FFT at f_{IN} = 3600 MHz](ad9081/figures/ad9081-f043.png)

*Figure 43. Single-Tone FFT at f_{IN} = 3600 MHz*

![Figure 44. Single-Tone FFT at f_{IN} = 4500 MHz](ad9081/figures/ad9081-f044.png)

*Figure 44. Single-Tone FFT at f_{IN} = 4500 MHz*

![Figure 45. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz](ad9081/figures/ad9081-f045.png)

*Figure 45. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz*

![Figure 46. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz](ad9081/figures/ad9081-f046.png)

*Figure 46. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz*

![Figure 47. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz](ad9081/figures/ad9081-f047.png)

*Figure 47. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz*

![Figure 48. Single-Tone FFT at f_{IN} = 5400 MHz](ad9081/figures/ad9081-f048.png)

*Figure 48. Single-Tone FFT at f_{IN} = 5400 MHz*

![Figure 49. Single-Tone FFT at f_{IN} = 6300 MHz](ad9081/figures/ad9081-f049.png)

*Figure 49. Single-Tone FFT at f_{IN} = 6300 MHz*

![Figure 50. Single-Tone FFT at f_{IN} = 7200 MHz](ad9081/figures/ad9081-f050.png)

*Figure 50. Single-Tone FFT at f_{IN} = 7200 MHz*

![Figure 51. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz](ad9081/figures/ad9081-f051.png)

*Figure 51. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz*

![Figure 52. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz](ad9081/figures/ad9081-f052.png)

*Figure 52. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz*

![Figure 53. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz](ad9081/figures/ad9081-f053.png)

*Figure 53. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz*

![Figure 54. Two-Tone FFT, f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz, A_{IN1} and A_{IN2} = -7 dBFS (IMD3L = 2f_{IN1} - f_{IN2} , and IMD3H = 2f_{IN2} - f_{IN1} )](ad9081/figures/ad9081-f054.png)

*Figure 54. Two-Tone FFT, f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz, A_{IN1} and A_{IN2} = -7 dBFS (IMD3L = 2f_{IN1} - f_{IN2} , and IMD3H = 2f_{IN2} - f_{IN1} )*

![Figure 55. Two-Tone FFT, f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f055.png)

*Figure 55. Two-Tone FFT, f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 56. Two-Tone FFT, f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f056.png)

*Figure 56. Two-Tone FFT, f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 57. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz](ad9081/figures/ad9081-f057.png)

*Figure 57. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz*

Digitized data: [two-tone-imd3-vs-a-in-with-f-in1-1-775-ghz-f-in2-1-825-ghz.csv](ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-1-775-ghz-f-in2-1-825-ghz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 58. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz](ad9081/figures/ad9081-f058.png)

*Figure 58. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz*

Digitized data: [two-tone-imd3-vs-a-in-with-f-in1-2-675-ghz-f-in2-2-725-ghz.csv](ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-2-675-ghz-f-in2-2-725-ghz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 59. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz](ad9081/figures/ad9081-f059.png)

*Figure 59. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz*

Digitized data: [two-tone-imd3-vs-a-in-with-f-in1-3-575-ghz-f-in2-3-625-ghz.csv](ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-3-575-ghz-f-in2-3-625-ghz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 60. Two-Tone FFT, f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f060.png)

*Figure 60. Two-Tone FFT, f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 61. SNR and SFDR vs. Input Frequency with A_{IN} =-1 dBFS](ad9081/figures/ad9081-f061.png)

*Figure 61. SNR and SFDR vs. Input Frequency with A_{IN} =-1 dBFS*

![Figure 62. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS](ad9081/figures/ad9081-f062.png)

*Figure 62. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS*

![Figure 63. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz](ad9081/figures/ad9081-f063.png)

*Figure 63. Two-Tone IMD3 vs. A_{IN} with f_{IN1} = 5.375 GHz, f_{IN2} = 5.425 GHz*

Digitized data: [two-tone-imd3-vs-a-in-with-f-in1-5-375-ghz-f-in2-5-425-ghz.csv](ad9081/curves/two-tone-imd3-vs-a-in-with-f-in1-5-375-ghz-f-in2-5-425-ghz.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 64. SNR vs. Input Frequency, Direct Clock vs. On-Chip PLL Clock,  f_{S}  = 4 GHz, A_{IN} = -1 dBFS](ad9081/figures/ad9081-f064.png)

*Figure 64. SNR vs. Input Frequency, Direct Clock vs. On-Chip PLL Clock,  f_{S}  = 4 GHz, A_{IN} = -1 dBFS*

Digitized data: [snr-vs-input-frequency-direct-clock-vs-on-chip-pll-clock-f-s-4-ghz-a-in-1-dbfs.csv](ad9081/curves/snr-vs-input-frequency-direct-clock-vs-on-chip-pll-clock-f-s-4-ghz-a-in-1-dbfs.csv) (x: MHz; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 65. FFT Close-In Comparison, Direct Clock vs. On-Chip PLL Clock,  f_{S} = 4 GHz, f_{IN} = 2.7 GHz, A_{IN} = -1 dBFS](ad9081/figures/ad9081-f065.png)

*Figure 65. FFT Close-In Comparison, Direct Clock vs. On-Chip PLL Clock,  f_{S} = 4 GHz, f_{IN} = 2.7 GHz, A_{IN} = -1 dBFS*

![Figure 66. SNR and SFDR vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS](ad9081/figures/ad9081-f066.png)

*Figure 66. SNR and SFDR vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS*

Digitized data: [snr-and-sfdr-vs-die-temperature-f-in-1-85-ghz-a-in-1-dbfs.csv](ad9081/curves/snr-and-sfdr-vs-die-temperature-f-in-1-85-ghz-a-in-1-dbfs.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 67. SNR and SFDR vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz](ad9081/figures/ad9081-f067.png)

*Figure 67. SNR and SFDR vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz*

Digitized data: [snr-and-sfdr-vs-sample-frequency-f-s-f-in-450-mhz.csv](ad9081/curves/snr-and-sfdr-vs-sample-frequency-f-s-f-in-450-mhz.csv) (x: GHz; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 68. Power vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS](ad9081/figures/ad9081-f068.png)

*Figure 68. Power vs. Die Temperature, f_{IN} = 1.85 GHz, A_{IN} = -1 dBFS*

Digitized data: [power-vs-die-temperature-f-in-1-85-ghz-a-in-1-dbfs.csv](ad9081/curves/power-vs-die-temperature-f-in-1-85-ghz-a-in-1-dbfs.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 69. Harmonics (HD2, HD3, and Interleaving) vs. Die Temperature, f_{IN} = 1.85 GHz](ad9081/figures/ad9081-f069.png)

*Figure 69. Harmonics (HD2, HD3, and Interleaving) vs. Die Temperature, f_{IN} = 1.85 GHz*

Digitized data: [harmonics-hd2-hd3-and-interleaving-vs-die-temperature-f-in-1-85-ghz.csv](ad9081/curves/harmonics-hd2-hd3-and-interleaving-vs-die-temperature-f-in-1-85-ghz.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 70. Harmonics (HD2 and HD3) vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz](ad9081/figures/ad9081-f070.png)

*Figure 70. Harmonics (HD2 and HD3) vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz*

Digitized data: [harmonics-hd2-and-hd3-vs-sample-frequency-f-s-f-in-450-mhz.csv](ad9081/curves/harmonics-hd2-and-hd3-vs-sample-frequency-f-s-f-in-450-mhz.csv) (x: GHz; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 71. Power vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz](ad9081/figures/ad9081-f071.png)

*Figure 71. Power vs. Sample Frequency (f_{S} ), f_{IN} = 450 MHz*

Digitized data: [power-vs-sample-frequency-f-s-f-in-450-mhz.csv](ad9081/curves/power-vs-sample-frequency-f-s-f-in-450-mhz.csv) (x: GHz; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 72. Input Referred Noise Histogram](ad9081/figures/ad9081-f072.png)

*Figure 72. Input Referred Noise Histogram*

![Figure 73. DNL, f_{IN} = 255 MHz](ad9081/figures/ad9081-f073.png)

*Figure 73. DNL, f_{IN} = 255 MHz*

![Figure 74. Measured Input Bandwidth ADC Input on AD9081-FMCA-EBZ (No Matching Network)](ad9081/figures/ad9081-f074.png)

*Figure 74. Measured Input Bandwidth ADC Input on AD9081-FMCA-EBZ (No Matching Network)*

Digitized data: [measured-input-bandwidth-adc-input-on-ad9081-fmca-ebz-no-matching-network.csv](ad9081/curves/measured-input-bandwidth-adc-input-on-ad9081-fmca-ebz-no-matching-network.csv) (x: GHz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 75. INL, f_{IN} = 255 MHz](ad9081/figures/ad9081-f075.png)

*Figure 75. INL, f_{IN} = 255 MHz*

### ADC: 3 GSPS

Nominal supplies, sampling rate = 3 GSPS with DAC clock frequency (f_{CLK} ) = 12 GHz direct RF clock, full bandwidth mode operation (no decimation), T_{J} = 80°C (T_{A} = 25°C), 128k FFT sample with five averages, and A_{IN} = -1 dBFS, unless otherwise noted.

![Figure 76. Single-Tone FFT at f_{IN} = 450 MHz](ad9081/figures/ad9081-f076.png)

*Figure 76. Single-Tone FFT at f_{IN} = 450 MHz*

![Figure 77. Single-Tone FFT at f_{IN} = 900 MHz](ad9081/figures/ad9081-f077.png)

*Figure 77. Single-Tone FFT at f_{IN} = 900 MHz*

![Figure 78. Single-Tone FFT at f_{IN} = 1800 MHz](ad9081/figures/ad9081-f078.png)

*Figure 78. Single-Tone FFT at f_{IN} = 1800 MHz*

![Figure 79. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz](ad9081/figures/ad9081-f079.png)

*Figure 79. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 450 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-ain-at-fin-450-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-ain-at-fin-450-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 80. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz](ad9081/figures/ad9081-f080.png)

*Figure 80. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 900 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-900-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-900-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 81. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz](ad9081/figures/ad9081-f081.png)

*Figure 81. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 1800 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-1800-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-1800-mhz.csv) (x: dBFS; y: dBc and dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 82. Single-Tone FFT at f_{IN} = 2700 MHz](ad9081/figures/ad9081-f082.png)

*Figure 82. Single-Tone FFT at f_{IN} = 2700 MHz*

![Figure 83. Single-Tone FFT at f_{IN} = 3600 MHz](ad9081/figures/ad9081-f083.png)

*Figure 83. Single-Tone FFT at f_{IN} = 3600 MHz*

![Figure 84. Single-Tone FFT at f_{IN} = 4500 MHz](ad9081/figures/ad9081-f084.png)

*Figure 84. Single-Tone FFT at f_{IN} = 4500 MHz*

![Figure 85. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz](ad9081/figures/ad9081-f085.png)

*Figure 85. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 2700 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-2700-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-2700-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 86. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz](ad9081/figures/ad9081-f086.png)

*Figure 86. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 3600 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-3600-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-3600-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 87. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz](ad9081/figures/ad9081-f087.png)

*Figure 87. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 4500 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-4500-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-4500-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 88. Single-Tone FFT at f_{IN} = 5400 MHz](ad9081/figures/ad9081-f088.png)

*Figure 88. Single-Tone FFT at f_{IN} = 5400 MHz*

![Figure 89. Single-Tone FFT at f_{IN} = 6300 MHz](ad9081/figures/ad9081-f089.png)

*Figure 89. Single-Tone FFT at f_{IN} = 6300 MHz*

![Figure 90. Single-Tone FFT at f_{IN} = 7200 MHz](ad9081/figures/ad9081-f090.png)

*Figure 90. Single-Tone FFT at f_{IN} = 7200 MHz*

![Figure 91. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz](ad9081/figures/ad9081-f091.png)

*Figure 91. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 5400 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-5400-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-5400-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 92. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz](ad9081/figures/ad9081-f092.png)

*Figure 92. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 6300 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-6300-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-6300-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 93. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz](ad9081/figures/ad9081-f093.png)

*Figure 93. Single-Tone SFDR and SNR vs. A_{IN} at f_{IN} = 7200 MHz*

Digitized data: [single-tone-sfdr-and-snr-vs-a-in-at-f-in-7200-mhz.csv](ad9081/curves/single-tone-sfdr-and-snr-vs-a-in-at-f-in-7200-mhz.csv) (x: dBFS; y: dBc AND dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 94. Two-Tone FFT, f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f094.png)

*Figure 94. Two-Tone FFT, f_{IN1} = 1.775 GHz, f_{IN2} = 1.825 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 95. Two-Tone FFT, f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f095.png)

*Figure 95. Two-Tone FFT, f_{IN1} = 3.575 GHz, f_{IN2} = 3.625 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 96. SNR and SFDR  vs. Input Frequency with A_{IN} =-1 dBFS](ad9081/figures/ad9081-f096.png)

*Figure 96. SNR and SFDR  vs. Input Frequency with A_{IN} =-1 dBFS*

Digitized data: [snr-and-sfdr-vs-input-frequency-with-a-in-1-dbfs.csv](ad9081/curves/snr-and-sfdr-vs-input-frequency-with-a-in-1-dbfs.csv) (x: MHz; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 97. Two-Tone FFT, f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f097.png)

*Figure 97. Two-Tone FFT, f_{IN1} = 2.675 GHz, f_{IN2} = 2.725 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 98. Two-Tone FFT, f_{IN1} = 5.575 GHz, f_{IN2} = 5.425 GHz, A_{IN1} and A_{IN2} = -7 dBFS](ad9081/figures/ad9081-f098.png)

*Figure 98. Two-Tone FFT, f_{IN1} = 5.575 GHz, f_{IN2} = 5.425 GHz, A_{IN1} and A_{IN2} = -7 dBFS*

![Figure 99. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS](ad9081/figures/ad9081-f099.png)

*Figure 99. Harmonics (HD2 and HD3) vs. Input Frequency with A_{IN} = -1 dBFS*

Digitized data: [harmonics-hd2-and-hd3-vs-input-frequency-with-a-in-1-dbfs.csv](ad9081/curves/harmonics-hd2-and-hd3-vs-input-frequency-with-a-in-1-dbfs.csv) (x: MHz; y: dBc) — values read off the printed plot by the digitizer, not published data.

### THEORY OF OPERATION

The AD9081 is a highly integrated, 28 nm, RF, MxFE featuring four 16-bit, 12 GSPS DAC cores and four 12-bit, 4 GSPS ADC cores (see Figure 1). The DAC core is based on a current segmentation architecture providing a differential complementary current output with an adjustable I_{OUTFS} range of 6.43 mA to 37.75 mA. The ADC core is based on a proprietary interleaved architecture that suppresses residual interleaving spurious products into the noise floor. To enable wide bandwidth operation, a high linearity, 100 Ω differential buffer with overload protection is used to isolate the ADC core from the RF ADC driver source. An on-chip clock multiplier can be used to synthesize the RF DAC and ADC clocks. Alternatively, an external clock can be applied.

Flexible transmit and receive DSP paths are available to up sample and down sample the desired intermediate frequency (IF) and RF signal(s) to lower the required data interface rates and efficiently align with bandwidth requirements. The channelizer data path enables efficient data transfer to allow multiband applications where up to eight unique RF bands are supported. The transmit and receive DSP paths are symmetric and consist of four coarse digital upconversion (DUC) and digital downconversion (DDC) blocks in the main data path along with eight fine DUC and DDC blocks in the channelizer data path. Each DUC and DDC block includes multiple interpolation or decimation stages and a 48-bit NCO configurable for integer or fractional mode of operation. The NCOs in the coarse DUC and DDC block support fast frequency hopping, coherently, and can be controlled using GPIOs. The DUC blocks, the DDC blocks, and the data paths can be fully bypassed to enable Nyquist operation.

Various auxiliary DSP features facilitate an improved system integration. The data paths include adjustable delay lines to compensate for mismatch in channel delay paths that may occur external to the device. The transmit data path includes digital gain control, fine delay adjust, and power amplifier protection to simplify DPD integration in a multiband transmitter. The receive data path includes a flexible, programmable, 192-tap finite impulse response (PFIR) filter. This filter can be allocated across one or more ADCs for receive equalization with support for four different profiles. The profiles can be selected using the GPIOx pins. The receive data path also includes a fast and slow signal detection capability in support of automatic gain control (AGC). The data paths also include features to reduce power consumption in time division duplex (TDD) applications. All the auxiliary DSP features can be fully bypassed.

The AD9081 also supports a low latency digital loopback between the receive and transmit data paths to bypass the JESD204 link. The data formatting of the data paths can be real or complex (I/Q) with selectable resolutions of 8, 12, 16, and 24 bits, depending on the JESD204B or the JESD204C mode.

A 16-lane JESD204 transceiver port is available to support the high data throughput rates on the receive and transmit data paths. Eight SERDES lanes are designated for the transmit data paths, whereas the other eight lanes are designated for the receive data paths. The transceiver port supports JESD204C up to 24.75 Gbps, or JESD204B up to 15.5 Gbps lane rates. The JESD204 data link layer is highly flexible, allowing to adjust the lane count (or rate) required to support a target link throughput. An external alignment signal (SYSREF) can be used to guarantee deterministic latency, phase alignment, and aid in multichip synchronization.

An on-chip thermal management unit (TMU) can be used to measure the die temperature as part of a thermal management solution to guarantee better thermal stability during system operation.

### APPLICATIONS INFORMATION

Refer to UG-1578, the device user guide, for more information on device initialization and other applications information.

### OUTLINE DIMENSIONS

![Figure 100. 324-Ball Ball Grid Array, Thermally Enhanced (BGA_ED) (BP-324-3) Dimensions shown in millimeters](ad9081/figures/ad9081-f101.png)

COMPLIANT TO JEDEC STANDARDS MO-275-KKAB-1

*Figure 100. 324-Ball Ball Grid Array, Thermally Enhanced [BGA_ED] (BP-324-3) Dimensions shown in millimeters*

### ORDERING GUIDE

**Ordering Guide** ([table-21-p45-data.csv](ad9081/tables/table-21-p45-data.csv), p. 45)

| Model[^1] | Temperature Range[^2] | Package Description | Packing Quantity | Package Option |
|---|---|---|---|---|
| AD9081BBPZ-4D4AB | −40°C to +120°C | 324-Ball BGA_ED (15 mm × 15 mm × 1.58 mm) | Tray, 126 | BP-324-3 |
| AD9081BBPZ-4D4AC | −40°C to +120°C | 324-Ball BGA_ED (15 mm × 15 mm × 1.58 mm) | Tray, 126 | BP-324-3 |
| AD9081BBPZRL-4D4AB | −40°C to +120°C | 324-Ball BGA_ED (15 mm × 15 mm × 1.58 mm) | Reel, 1000 | BP-324-3 |
| AD9081BBPZRL-4D4AC | −40°C to +120°C | 324-Ball BGA_ED (15 mm × 15 mm × 1.58 mm) | Reel, 1000 | BP-324-3 |

- **Note 1:** Z = RoHS Compliant Part
- **Note 2:** Specified operating junction temperature (T_{J}).

### EVALUATION BOARDS

**Evaluation Boards** ([table-22-p45-data.csv](ad9081/tables/table-22-p45-data.csv), p. 45)

| Model | Description |
|---|---|
| AD9081-FMCA-EBZ | AD9081 Evaluation Board with High Performance Analog Network |
