---
type: Analog Component
title: "AD8210 — High Voltage, Bidirectional Current Shunt Monitor"
description: "High Voltage, Bidirectional Current Shunt Monitor"
resource: "https://www.analog.com/en/products/ad8210.html"
tags: ["datasheet", "adi"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ad8210.pdf"
    title: "AD8210 data sheet"
    author: "team:analog-devices"
    last_modified: "5/2020"
tables:
  - file: "ad8210/tables/table-00-p3-spec.csv"
    title: "Table 1."
    page: 3
  - file: "ad8210/tables/table-01-p4-abs_max.csv"
    title: "Table 2."
    page: 4
  - file: "ad8210/tables/table-02-p5-pin.csv"
    title: "Table 3. Pin Function Descriptions"
    page: 5
  - file: "ad8210/tables/table-03-p11-data.csv"
    title: "Table 4. V+ = 5 V"
    page: 11
  - file: "ad8210/tables/table-04-p11-data.csv"
    title: "Table 5. V+ = 5 V"
    page: 11
  - file: "ad8210/tables/table-05-p11-data.csv"
    title: "Table 6. V+ = 5 V, VO = 2.5 V with VIN = 0 V"
    page: 11
  - file: "ad8210/tables/table-06-p15-data.csv"
    title: "Ordering Guide"
    page: 15
figures:
  - file: "ad8210/figures/ad8210-f001.png"
    caption: "Figure 1. Functional Block Diagram"
    type: "block_diagram"
    page: 1
  - file: "ad8210/figures/ad8210-f003.png"
    caption: "Figure 2. Pin Configuration"
    type: "pinout"
    page: 5
  - file: "ad8210/figures/ad8210-f004.png"
    caption: "Figure 3. Typical Offset Drift"
    type: "characteristic_curve"
    page: 6
  - file: "ad8210/figures/ad8210-f005.png"
    caption: "Figure 4. CMRR vs. Frequency and Temperature (Common-Mode Voltage < 5 V)"
    type: "characteristic_curve"
    page: 6
  - file: "ad8210/figures/ad8210-f006.png"
    caption: "Figure 5. CMRR vs. Frequency and Temperature (Common-Mode Voltage > 5 V)"
    type: "characteristic_curve"
    page: 6
  - file: "ad8210/figures/ad8210-f007.png"
    caption: "Figure 6. Typical Gain Drift"
    type: "characteristic_curve"
    page: 6
  - file: "ad8210/figures/ad8210-f008.png"
    caption: "Figure 7. Typical Small Signal Bandwidth (Output Voltage (Vout) = 200 mV p-p)"
    type: "characteristic_curve"
    page: 6
  - file: "ad8210/figures/ad8210-f009.png"
    caption: "Figure 8. Fall Time"
    type: "scope_capture"
    page: 6
  - file: "ad8210/figures/ad8210-f010.png"
    caption: "Figure 9. Rise Time"
    type: "scope_capture"
    page: 7
  - file: "ad8210/figures/ad8210-f011.png"
    caption: "Figure 10. Differential Overload Recovery (Falling)"
    type: "scope_capture"
    page: 7
  - file: "ad8210/figures/ad8210-f012.png"
    caption: "Figure 11. Differential Overload Recovery (Rising)"
    type: "scope_capture"
    page: 7
  - file: "ad8210/figures/ad8210-f013.png"
    caption: "Figure 12. Settling Time (Falling)"
    type: "scope_capture"
    page: 7
  - file: "ad8210/figures/ad8210-f014.png"
    caption: "Figure 13. Settling Time (Rising)"
    type: "scope_capture"
    page: 7
  - file: "ad8210/figures/ad8210-f015.png"
    caption: "Figure 14. Common-Mode Response (Falling)"
    type: "scope_capture"
    page: 7
  - file: "ad8210/figures/ad8210-f016.png"
    caption: "Figure 15. Common-Mode Response (Rising)"
    type: "scope_capture"
    page: 8
  - file: "ad8210/figures/ad8210-f017.png"
    caption: "Figure 16. Common-Mode Step Recovery Error (Rising)"
    type: "characteristic_curve"
    page: 8
  - file: "ad8210/figures/ad8210-f018.png"
    caption: "Figure 17. Common-Mode Step Recovery Error (Falling)"
    type: "characteristic_curve"
    page: 8
  - file: "ad8210/figures/ad8210-f019.png"
    caption: "Figure 18. Output Sink Current vs. Temperature"
    type: "characteristic_curve"
    page: 8
  - file: "ad8210/figures/ad8210-f020.png"
    caption: "Figure 19. Output Source Current vs. Temperature"
    type: "characteristic_curve"
    page: 8
  - file: "ad8210/figures/ad8210-f021.png"
    caption: "Figure 20. Output Voltage Range vs. Output Source Current"
    type: "characteristic_curve"
    page: 8
  - file: "ad8210/figures/ad8210-f022.png"
    caption: "Figure 21. Output Voltage Range from GND vs. Output Sink Current"
    type: "characteristic_curve"
    page: 9
  - file: "ad8210/figures/ad8210-f023.png"
    caption: "Figure 22. Supply Current vs. Common-Mode Voltage"
    type: "characteristic_curve"
    page: 9
  - file: "ad8210/figures/ad8210-f024.png"
    caption: "Figure 23. Offset Drift Distribution (μV/°C), SOIC, Temperature Range = −40℃ to +125℃"
    type: "characteristic_curve"
    page: 9
  - file: "ad8210/figures/ad8210-f025.png"
    caption: "Figure 24. Gain Drift Distribution (ppm/°C), SOIC, Temperature = −40℃ to +125℃"
    type: "characteristic_curve"
    page: 9
  - file: "ad8210/figures/ad8210-f026.png"
    caption: "Figure 25. Offset Distribution (μV), SOIC, VCM = 5V"
    type: "characteristic_curve"
    page: 9
  - file: "ad8210/figures/ad8210-f027.png"
    caption: "Figure 26. Offset Distribution (μV), SOIC, VCM = 0V"
    type: "characteristic_curve"
    page: 9
  - file: "ad8210/figures/ad8210-f028.png"
    caption: "Figure 27. Simplified Schematic"
    type: "block_diagram"
    page: 10
  - file: "ad8210/figures/ad8210-f029.png"
    caption: "Figure 28. Ground Referenced Output"
    type: "application_circuit"
    page: 11
  - file: "ad8210/figures/ad8210-f030.png"
    caption: "Figure 29. V+ Referenced Output"
    type: "application_circuit"
    page: 11
  - file: "ad8210/figures/ad8210-f031.png"
    caption: "Figure 30. External Reference Output"
    type: "application_circuit"
    page: 12
  - file: "ad8210/figures/ad8210-f032.png"
    caption: "Figure 31. Split External Reference"
    type: "application_circuit"
    page: 12
  - file: "ad8210/figures/ad8210-f033.png"
    caption: "Figure 32. Split Supply"
    type: "application_circuit"
    page: 12
  - file: "ad8210/figures/ad8210-f034.png"
    caption: "Figure 33. Input Low-Pass Filtering"
    type: "application_circuit"
    page: 13
  - file: "ad8210/figures/ad8210-f035.png"
    caption: "Figure 34. Low-Side Switch"
    type: "application_circuit"
    page: 14
  - file: "ad8210/figures/ad8210-f036.png"
    caption: "Figure 35. High-Side Switch"
    type: "application_circuit"
    page: 14
  - file: "ad8210/figures/ad8210-f037.png"
    caption: "Figure 36. Motor Control Application"
    type: "application_circuit"
    page: 14
  - file: "ad8210/figures/ad8210-f038.png"
    caption: "Figure 37. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches)"
    type: "other"
    page: 15
  - file: "ad8210/figures/ad8210-eq01-recrop.png"
    caption: "Equation as printed (p. 13)"
    type: equation
    page: 13
  - file: "ad8210/figures/ad8210-eq02-recrop.png"
    caption: "Equation as printed (p. 13)"
    type: equation
    page: 13
curves:
  - file: "ad8210/curves/cmrr-vs-frequency-and-temperature-common-mode-voltage-less-than-5-v.csv"
    caption: "Figure 4. CMRR vs. Frequency and Temperature (Common-Mode Voltage < 5 V)"
    figure: "ad8210/figures/ad8210-f005.png"
    page: 6
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ad8210/curves/cmrr-vs-frequency-and-temperature-common-mode-voltage-greater-than-5-v.csv"
    caption: "Figure 5. CMRR vs. Frequency and Temperature (Common-Mode Voltage > 5 V)"
    figure: "ad8210/figures/ad8210-f006.png"
    page: 6
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ad8210/curves/common-mode-step-recovery-error-falling.csv"
    caption: "Figure 17. Common-Mode Step Recovery Error (Falling)"
    figure: "ad8210/figures/ad8210-f018.png"
    page: 8
    x_unit: "ns"
    y_unit: "mV"
  - file: "ad8210/curves/common-mode-step-recovery-error-rising.csv"
    caption: "Figure 16. Common-Mode Step Recovery Error (Rising)"
    figure: "ad8210/figures/ad8210-f017.png"
    page: 8
    x_unit: "ns"
    y_unit: "mV"
  - file: "ad8210/curves/supply-current-vs-common-mode-voltage.csv"
    caption: "Figure 22. Supply Current vs. Common-Mode Voltage"
    figure: "ad8210/figures/ad8210-f023.png"
    page: 9
    x_unit: "V"
    y_unit: "mA"
  - file: "ad8210/curves/figure-24-gain-drift-distribution-ppm-c-soic-temperature-40-to-125.csv"
    caption: "Figure 24. Gain Drift Distribution (ppm/°C), SOIC, Temperature = −40℃ to +125℃"
    figure: "ad8210/figures/ad8210-f025.png"
    page: 9
    x_unit: "ppm/°C"
    y_unit: "COUNT"
  - file: "ad8210/curves/offset-distribution-v-soic-vcm-0v.csv"
    caption: "Figure 26. Offset Distribution (μV), SOIC, VCM = 0V"
    figure: "ad8210/figures/ad8210-f027.png"
    page: 9
    x_unit: "mV"
    y_unit: "COUNT"
    conditions: "VCM = 0V, SOIC"
  - file: "ad8210/curves/offset-distribution-v-soic-vcm-5v.csv"
    caption: "Figure 25. Offset Distribution (μV), SOIC, VCM = 5V"
    figure: "ad8210/figures/ad8210-f026.png"
    page: 9
    x_unit: "mV"
    y_unit: "COUNT"
    conditions: "+125°C, +25°C, -40°C"
  - file: "ad8210/curves/offset-drift-distribution-v-c-soic-temperature-range-40-to-125.csv"
    caption: "Figure 23. Offset Drift Distribution (μV/°C), SOIC, Temperature Range = −40℃ to +125℃"
    figure: "ad8210/figures/ad8210-f024.png"
    page: 9
    x_unit: "μV/°C"
    y_unit: "COUNT"
  - file: "ad8210/curves/output-sink-current-vs-temperature.csv"
    caption: "Figure 18. Output Sink Current vs. Temperature"
    figure: "ad8210/figures/ad8210-f019.png"
    page: 8
    x_unit: "°C"
    y_unit: "mA"
  - file: "ad8210/curves/output-source-current-vs-temperature.csv"
    caption: "Figure 19. Output Source Current vs. Temperature"
    figure: "ad8210/figures/ad8210-f020.png"
    page: 8
    x_unit: "°C"
    y_unit: "mA"
  - file: "ad8210/curves/output-voltage-range-from-gnd-vs-output-sink-current.csv"
    caption: "Figure 21. Output Voltage Range from GND vs. Output Sink Current"
    figure: "ad8210/figures/ad8210-f022.png"
    page: 9
    x_unit: "mA"
    y_unit: "V"
  - file: "ad8210/curves/output-voltage-range-vs-output-source-current.csv"
    caption: "Figure 20. Output Voltage Range vs. Output Source Current"
    figure: "ad8210/figures/ad8210-f021.png"
    page: 8
    x_unit: "mA"
    y_unit: "V"
  - file: "ad8210/curves/typical-gain-drift.csv"
    caption: "Figure 6. Typical Gain Drift"
    figure: "ad8210/figures/ad8210-f007.png"
    page: 6
    x_unit: "°C"
    y_unit: "ppm"
  - file: "ad8210/curves/typical-offset-drift.csv"
    caption: "Figure 3. Typical Offset Drift"
    figure: "ad8210/figures/ad8210-f004.png"
    page: 6
    x_unit: "°C"
    y_unit: "µV"
  - file: "ad8210/curves/typical-small-signal-bandwidth-output-voltage-vout-200-mv-p-p.csv"
    caption: "Figure 7. Typical Small Signal Bandwidth (Output Voltage (Vout) = 200 mV p-p)"
    figure: "ad8210/figures/ad8210-f008.png"
    page: 6
    x_unit: "Hz"
    y_unit: "dB"
agentforge:
  part_number: "AD8210"
  datasheet_revision: "F"
  reading_order: "geometry"
---

# AD8210 — High Voltage, Bidirectional Current Shunt Monitor

*Datasheet: [AD8210 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ad8210.pdf)*

### FEATURES

±4000 V HBM ESD

High common-mode voltage range

 - -2 V to +65 V operating

 - -5 V to +68 V survival 

Buffered output voltage

5 mA output drive capability

Wide operating temperature range: -40°C to +125°C

Ratiometric half-scale output offset

Excellent ac and dc performance

  - 1 µV/°C typical offset drift

  - 10 ppm/°C typical gain drift

  - 120 dB typical CMRR at dc

  - 80 dB typical CMRR at 100 kHz

Available in 8-lead SOIC

Qualified for automotive applications

### APPLICATIONS

Current sensing
- Motor controls
-  Transmission controls 
- Diesel injection controls 
- Engine management 
- Suspension controls 
- Vehicle dynamic controls 
- DC-to-dc converters

### GENERAL DESCRIPTION

The AD8210 is a single-supply, difference amplifier ideal for amplifying small differential voltages in the presence of large common-mode voltages. The operating input common-mode voltage range extends from -2 V to +65 V. The typical supply voltage is 5 V.

The AD8210 is offered in a SOIC package. The operating temperature range is -40°C to +125°C.

Excellent ac and dc performance over temperature keep errors in the measurement loop to a minimum. Offset drift and gain drift are guaranteed to a maximum of 8 µV/°C and 20 ppm/°C, respectively.

The output offset can be adjusted from 0.05 V to 4.9 V with a 5 V supply by using the $V_{REF}1$ pin and the $V_{REF}2$ pin. With the $V_{REF}1$ pin attached to the V+ pin and the $V_{REF}2$ pin attached to the GND pin, the output is set at half scale. Attaching both $V_{REF}1$ and $V_{REF}2$ to GND causes the output to be unipolar, starting near ground. Attaching both $V_{REF}1$ and $V_{REF}2$ to V+ causes the output to be unipolar, starting near V+. Other offsets can be obtained by applying an external voltage to $V_{REF}1$ and $V_{REF}2$.

### FUNCTIONAL BLOCK DIAGRAM

![Figure 1](ad8210/figures/ad8210-f001.png)

*Figure 1*

### TABLE OF CONTENTS

- Features
- Applications
- Functional Block Diagram
- General Description
- Revision History
- Specifications
- Absolute Maximum Ratings
  - ESD Caution
- Pin Configuration and Function Descriptions
- Typical Performance Characteristics
- Theory of Operation
- Modes of Operation
  - Unidirectional Operation
  - Bidirectional Operation
- Input Filtering
- Applications Information
  - High-Side Current Sense with a Low-Side Switch
  - High-Side Current Sense with a High-Side Switch
  - H-Bridge Motor Control
- Outline Dimensions
  - Ordering Guide
  - Automotive Products

#### REVISION HISTORY
 **5/2020-Rev. E to Rev. F**
- Change to Table 2
- Deleted Figure 3, Renumbered Sequentially
- Changes to Table 3
- Changes to Figure 7 and Figure 8
- Changes to Figure 9 to Figure 14
- Changes to Figure 15
- Added Figure 16 and Figure 17

**9/2017-Rev. D to Rev. E**
- Change to Ordering Guide
- 6/2013-Rev. C to Rev. D
- Added Automotive Information (Throughout)
- Changes to Equation 1
- Added Automotive Products Section

**2/2012-Rev. B to Rev. C**
- Changes to Ordering Guide

**5/2009-Rev. A to Rev. B**
-  Changes to Ordering Guide

**4/2007-Rev. 0 to Rev. A**
- Changes to Features
- Changes to Input Section
- Updated Outline Dimensions

**4/2006-Revision 0: Initial Version**

### SPECIFICATIONS

$T_{A}$ = operating temperature range, $V_{S}$ = 5 V, unless otherwise noted.

**Table 1.** ([table-00-p3-spec.csv](ad8210/tables/table-00-p3-spec.csv), p. 3)

| PARAMETER | AD8210 SOIC $[^{1}]$ - MIN | AD8210 SOIC $[^{1}]$ - TYP | AD8210 SOIC $[^{1}]$ - MAX | UNITS | CONDITIONS |
|---|---|---|---|---|---|
| **GAIN** |  |  |  |  |  |
| Initial |  | 20 |  | V/V |  |
| Accuracy |  |  | ±0.5 | % | 25°C, $V_{O}$ ≥ 0.1 V dc |
| Accuracy Over Temperature |  |  | ±0.7 | % | $T_{A}$ |
| Gain Drift |  |  | 20 | ppm/°C |  |
| **VOLTAGE OFFSET** |  |  |  |  |  |
| Offset Voltage (RTI) |  |  | ±1.0 | mV | 25°C |
| Over Temperature (RTI) |  |  | ±1.8 | mV | $T_{A}$ |
| Offset Drift |  |  | ±8.0 | µV/°C |  |
| **INPUT** |  |  |  |  |  |
| Input Impedance |  |  |  |  |  |
| Differential |  | 2 |  | kΩ |  |
| Common Mode |  | 5 |  | MΩ | V common mode > 5 V |
|  |  | 1.5 |  | kΩ | V common mode < 5 V |
| Common-Mode Input Voltage Range | −2 |  | +65 | V | Common mode, continuous |
| Differential Input Voltage Range |  | 250 |  | mV | Differential $[^{2}]$ |
| Common-Mode Rejection | 100 | 120 |  | dB | $T_{A}$, f = dc, $V_{CM}$ > 5 V |
|  | 80 | 95 |  | dB | $T_{A}$, f = dc to 100 kHz $[^{3}]$, $V_{CM}$ < 5 V |
|  |  | 80 |  | dB | $T_{A}$, f = 100 kHz $[^{3}]$, $V_{CM}$ > 5 V |
|  | 80 |  |  | dB | $T_{A}$, f = 40 kHz $[^{3}]$, $V_{CM}$ > 5 V |
| **OUTPUT** |  |  |  |  |  |
| Output Voltage Range | 0.05 |  | 4.9 | V | $R_{L}$ = 25 kΩ |
| Output Impedance |  | 2 |  | Ω |  |
| **DYNAMIC RESPONSE** |  |  |  |  |  |
| Small Signal −3 dB Bandwidth |  | 450 |  | kHz |  |
| Slew Rate |  | 3 |  | V/µs |  |
| **NOISE** |  |  |  |  |  |
| 0.1 Hz to 10 Hz, RTI |  | 7 |  | µV p-p |  |
| Spectral Density, 1 kHz, RTI |  | 70 |  | $nV/\sqrt{Hz}$ |  |
| **OFFSET ADJUSTMENT** |  |  |  |  |  |
| Ratiometric Accuracy $[^{4}]$ | 0.499 |  | 0.501 | V/V | Divider to supplies |
| Accuracy, RTO |  |  | ±0.6 | mV/V | Voltage applied to $V_{REF}1$ and $V_{REF}2$ in parallel |
| Output Offset Adjustment Range | 0.05 |  | 4.9 | V | $V_{S}$ = 5 V |
| $V_{REF}$ Input Voltage Range | 0.0 |  | $V_{S}$ | V |  |
| $V_{REF}$ Divider Resistor Values | 24 | 32 | 40 | kΩ |  |
| **POWER SUPPLY, $V_{S}$** |  |  |  |  |  |
| Operating Range | 4.5 | 5.0 | 5.5 | V |  |
| Quiescent Current Over Temperature |  |  | 2 | mA | $V_{CM}$ > 5 V $[^{5}]$ |
| Power Supply Rejection Ratio | 80 |  |  | dB |  |
| **TEMPERATURE RANGE** |  |  |  |  |  |
| For Specified Performance | −40 |  | +125 | °C |  |

$[^{1}]$: $T_{MIN}$ to $T_{MAX}$ = −40°C to +125°C.

$[^{2}]$: Differential input voltage range = ±125 mV with half-scale output offset.

$[^{3}]$: Source imbalance < 2 Ω.

$[^{4}]$: The offset adjustment is ratiometric to the power supply when $V_{REF}1$ and $V_{REF}2$ are used as a divider between the supplies.

$[^{5}]$: When the input common mode is less than 5 V, the supply current increases. This can be calculated with the following formula: $I_{S}$ = −0.7 ($V_{CM}$) + 4.2 (see Figure 22).

### ABSOLUTE MAXIMUM RATINGS

**Table 2.** ([table-01-p4-abs_max.csv](ad8210/tables/table-01-p4-abs_max.csv), p. 4)

| PARAMETER | RATING |
|---|---|
| Supply Voltage | 12.5 V |
| Continuous Input Voltage ($V_{CM}$) | −5 V to +68 V |
| Reverse Supply Voltage | 0.3 V |
| **ESD Rating** |  |
| HBM (Human Body Model) | ±4000 V |
| CDM (Charged Device Model) | ±1250 V |
| Operating Temperature Range | −40°C to +125°C |
| Storage Temperature Range | −65°C to +150°C |
| Output Short-Circuit Duration | Indefinite |

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

### ESD CAUTION

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

### PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

![Figure 2. Pin Configuration](ad8210/figures/ad8210-f003.png)

*Figure 2. Pin Configuration*

**Table 3. Pin Function Descriptions** ([table-02-p5-pin.csv](ad8210/tables/table-02-p5-pin.csv), p. 5)

| Pin No. | Mnemonic |
|---|---|
| 1 | −IN |
| 2 | GND |
| 3 | $V_{REF}2$ |
| 4 | NC |
| 5 | OUT |
| 6 | V+ |
| 7 | $V_{REF}1$ |
| 8 | +IN |

### TYPICAL PERFORMANCE CHARACTERISTICS

![Figure 3. Typical Offset Drift](ad8210/figures/ad8210-f004.png)

*Figure 3. Typical Offset Drift*

Digitized data: [typical-offset-drift.csv](ad8210/curves/typical-offset-drift.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 4. CMRR vs. Frequency and Temperature (Common-Mode Voltage < 5 V)](ad8210/figures/ad8210-f005.png)

*Figure 4. CMRR vs. Frequency and Temperature (Common-Mode Voltage < 5 V)*

Digitized data: [cmrr-vs-frequency-and-temperature-common-mode-voltage-less-than-5-v.csv](ad8210/curves/cmrr-vs-frequency-and-temperature-common-mode-voltage-less-than-5-v.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 5. CMRR vs. Frequency and Temperature (Common-Mode Voltage > 5 V)](ad8210/figures/ad8210-f006.png)

*Figure 5. CMRR vs. Frequency and Temperature (Common-Mode Voltage > 5 V)*

Digitized data: [cmrr-vs-frequency-and-temperature-common-mode-voltage-greater-than-5-v.csv](ad8210/curves/cmrr-vs-frequency-and-temperature-common-mode-voltage-greater-than-5-v.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 6. Typical Gain Drift](ad8210/figures/ad8210-f007.png)

*Figure 6. Typical Gain Drift*

Digitized data: [typical-gain-drift.csv](ad8210/curves/typical-gain-drift.csv) (x: °C; y: ppm) — values read off the printed plot by the digitizer, not published data.

![Figure 7. Typical Small Signal Bandwidth (Output Voltage (Vout) = 200 mV p-p)](ad8210/figures/ad8210-f008.png)

*Figure 7. Typical Small Signal Bandwidth (Output Voltage ($V_{OUT}$) = 200 mV p-p)*

Digitized data: [typical-small-signal-bandwidth-output-voltage-vout-200-mv-p-p.csv](ad8210/curves/typical-small-signal-bandwidth-output-voltage-vout-200-mv-p-p.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 8. Fall Time](ad8210/figures/ad8210-f009.png)

*Figure 8. Fall Time*

![Figure 9. Rise Time](ad8210/figures/ad8210-f010.png)

*Figure 9. Rise Time*

![Figure 10. Differential Overload Recovery (Falling)](ad8210/figures/ad8210-f011.png)

*Figure 10. Differential Overload Recovery (Falling)*

![Figure 11. Differential Overload Recovery (Rising)](ad8210/figures/ad8210-f012.png)

*Figure 11. Differential Overload Recovery (Rising)*

![Figure 12. Settling Time (Falling)](ad8210/figures/ad8210-f013.png)

*Figure 12. Settling Time (Falling)*

![Figure 13. Settling Time (Rising)](ad8210/figures/ad8210-f014.png)

*Figure 13. Settling Time (Rising)*

![Figure 14. Common-Mode Response (Falling)](ad8210/figures/ad8210-f015.png)

*Figure 14. Common-Mode Response (Falling)*

![Figure 15. Common-Mode Response (Rising)](ad8210/figures/ad8210-f016.png)

*Figure 15. Common-Mode Response (Rising)*

![Figure 16. Common-Mode Step Recovery Error (Rising)](ad8210/figures/ad8210-f017.png)

*Figure 16. Common-Mode Step Recovery Error (Rising)*

Digitized data: [common-mode-step-recovery-error-rising.csv](ad8210/curves/common-mode-step-recovery-error-rising.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 17. Common-Mode Step Recovery Error (Falling)](ad8210/figures/ad8210-f018.png)

*Figure 17. Common-Mode Step Recovery Error (Falling)*

Digitized data: [common-mode-step-recovery-error-falling.csv](ad8210/curves/common-mode-step-recovery-error-falling.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 18. Output Sink Current vs. Temperature](ad8210/figures/ad8210-f019.png)

*Figure 18. Output Sink Current vs. Temperature*

Digitized data: [output-sink-current-vs-temperature.csv](ad8210/curves/output-sink-current-vs-temperature.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 19. Output Source Current vs. Temperature](ad8210/figures/ad8210-f020.png)

*Figure 19. Output Source Current vs. Temperature*

Digitized data: [output-source-current-vs-temperature.csv](ad8210/curves/output-source-current-vs-temperature.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 20. Output Voltage Range vs. Output Source Current](ad8210/figures/ad8210-f021.png)

*Figure 20. Output Voltage Range vs. Output Source Current*

Digitized data: [output-voltage-range-vs-output-source-current.csv](ad8210/curves/output-voltage-range-vs-output-source-current.csv) (x: mA; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 21. Output Voltage Range from GND vs. Output Sink Current](ad8210/figures/ad8210-f022.png)

*Figure 21. Output Voltage Range from GND vs. Output Sink Current*

Digitized data: [output-voltage-range-from-gnd-vs-output-sink-current.csv](ad8210/curves/output-voltage-range-from-gnd-vs-output-sink-current.csv) (x: mA; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 22. Supply Current vs. Common-Mode Voltage](ad8210/figures/ad8210-f023.png)

*Figure 22. Supply Current vs. Common-Mode Voltage*

Digitized data: [supply-current-vs-common-mode-voltage.csv](ad8210/curves/supply-current-vs-common-mode-voltage.csv) (x: V; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 23. Offset Drift Distribution (µV/°C), SOIC, Temperature Range = −40℃ to +125℃](ad8210/figures/ad8210-f024.png)

*Figure 23. Offset Drift Distribution (µV/°C), SOIC, Temperature Range = −40℃ to +125℃*

Digitized data: [offset-drift-distribution-v-c-soic-temperature-range-40-to-125.csv](ad8210/curves/offset-drift-distribution-v-c-soic-temperature-range-40-to-125.csv) (x: μV/°C; y: COUNT) — values read off the printed plot by the digitizer, not published data.

![Figure 24. Gain Drift Distribution (ppm/°C), SOIC, Temperature = −40℃ to +125℃](ad8210/figures/ad8210-f025.png)

*Figure 24. Gain Drift Distribution (ppm/°C), SOIC, Temperature = −40℃ to +125℃*

Digitized data: [figure-24-gain-drift-distribution-ppm-c-soic-temperature-40-to-125.csv](ad8210/curves/figure-24-gain-drift-distribution-ppm-c-soic-temperature-40-to-125.csv) (x: ppm/°C; y: COUNT) — values read off the printed plot by the digitizer, not published data.

![Figure 25. Offset Distribution (µV), SOIC, VCM = 5V](ad8210/figures/ad8210-f026.png)

*Figure 25. Offset Distribution (µV), SOIC, VCM = 5V*

Digitized data: [offset-distribution-v-soic-vcm-5v.csv](ad8210/curves/offset-distribution-v-soic-vcm-5v.csv) (x: mV; y: COUNT) — values read off the printed plot by the digitizer, not published data.

![Figure 26. Offset Distribution (µV), SOIC, VCM = 0V](ad8210/figures/ad8210-f027.png)

*Figure 26. Offset Distribution (µV), SOIC, VCM = 0V*

Digitized data: [offset-distribution-v-soic-vcm-0v.csv](ad8210/curves/offset-distribution-v-soic-vcm-0v.csv) (x: mV; y: COUNT) — values read off the printed plot by the digitizer, not published data.



### THEORY OF OPERATION

In typical applications, the AD8210 amplifies a small differential input voltage generated by the load current flowing through a shunt resistor. The AD8210 rejects high common-mode voltages (up to 65 V) and provides a ground referenced buffered output that interfaces with an analog-to-digital converter (ADC). Figure 27 shows a simplified schematic of the AD8210.

The AD8210 is comprised of two main blocks, a differential amplifier and an instrumentation amplifier. A load current flowing through the external shunt resistor produces a voltage at the input terminals of the AD8210. The input terminals are connected to the differential amplifier (A1) by R1 and R2. A1 nulls the voltage appearing across its own input terminals by adjusting the current through R1 and R2 with Q1 and Q2. When the input signal to the AD8210 is 0 V, the currents in R1 and R2 are equal. When the differential signal is nonzero, the current increases through one of the resistors and decreases in the other. The current difference is proportional to the size and polarity of the input signal.

The differential currents through Q1 and Q2 are converted into a differential voltage by R3 and R4. A2 is configured as an instrumentation amplifier. The differential voltage is converted into a single-ended output voltage by A2. The gain is internally set with precision-trimmed, thin film resistors to 20 V/V.

The output reference voltage is easily adjusted by the $V_{REF}1$ pin and the $V_{REF}2$ pin. In a typical configuration, $V_{REF}1$ is connected to $V_{CC}$ while $V_{REF}2$ is connected to GND. In this case, the output is centered at $V_{CC}$/2 when the input signal is 0 V.

![Figure 27. Simplified Schematic](ad8210/figures/ad8210-f028.png)

*Figure 27. Simplified Schematic*

### MODES OF OPERATION

The AD8210 can be adjusted for unidirectional or bidirectional operation.

#### UNIDIRECTIONAL OPERATION

Unidirectional operation allows the AD8210 to measure currents through a resistive shunt in one direction. The basic modes for unidirectional operation are ground referenced output mode and V+ referenced output mode.

In unidirectional operation, the output can be set at the negative rail (near ground) or at the positive rail (near V+) when the differential input is 0 V. The output moves to the opposite rail when a correct polarity differential input voltage is applied. In this case, full scale is approximately 250 mV. The required polarity of the differential input depends on the output voltage setting. If the output is set at ground, the polarity needs to be positive to move the output up (see Table 5). If the output is set at the positive rail, the input polarity needs to be negative to move the output down (see Table 6).

#### Ground Referenced Output

When using the AD8210 in this mode, both reference inputs are tied to ground, which causes the output to sit at the negative rail when the differential input voltage is zero (see Figure 28 and Table 4).

![Figure 28. Ground Referenced Output](ad8210/figures/ad8210-f029.png)

*Figure 28. Ground Referenced Output*

**Table 4. V+ = 5 V** ([table-03-p11-data.csv](ad8210/tables/table-03-p11-data.csv), p. 11)

| $V_{IN}$ (Referred to −IN) | $V_{O}$ |
|---|---|
| 0 V | 0.05 V |
| 250 mV | 4.9 V |

#### V+ Referenced Output

This mode is set when both reference pins are tied to the positive supply. It is typically used when the diagnostic scheme requires detection of the amplifier and wiring before power is applied to the load (see Figure 29 and Table 5).

![Figure 29. V+ Referenced Output](ad8210/figures/ad8210-f030.png)

*Figure 29. V+ Referenced Output*

**Table 5. V+ = 5 V** ([table-04-p11-data.csv](ad8210/tables/table-04-p11-data.csv), p. 11)

| $V_{IN}$ (Referred to −IN) | $V_{O}$ |
|---|---|
| 0 V | 4.9 V |
| −250 mV | 0.05 V |

#### BIDIRECTIONAL OPERATION

Bidirectional operation allows the AD8210 to measure currents through a resistive shunt in two directions. The output offset can be set anywhere within the output range. Typically, it is set at half scale for equal measurement range in both directions. In some cases, however, it is set at a voltage other than half scale when the bidirectional current is nonsymmetrical.

**Table 6. V+ = 5 V, $V_{O}$ = 2.5 V with $V_{IN}$ = 0 V** ([table-05-p11-data.csv](ad8210/tables/table-05-p11-data.csv), p. 11)

| $V_{IN}$ (Referred to −IN) | $V_{O}$ |
|---|---|
| +125 mV | 4.9 V |
| −125 mV | 0.05 V |

Adjusting the output can also be accomplished by applying voltage(s) to the reference inputs.

#### External Referenced Output

Tying both $V_{REF}$ pins together to an external reference produces an output offset at the reference voltage when there is no differential input (see Figure 30). When the input is negative relative to the -IN pin, the output moves down from the reference voltage. When the input is positive relative to the -IN pin, the output increases.

![Figure 30. External Reference Output](ad8210/figures/ad8210-f031.png)

*Figure 30. External Reference Output*

#### Splitting an External Reference

In this case, an external reference is divided by two with an accuracy of approximately 0.2% by connecting one $V_{REF}$ pin to ground and the other $V_{REF}$ pin to the reference voltage (see Figure 31).

Note that Pin $V_{REF}1$ and Pin $V_{REF}2$ are tied to internal precision resistors that connect to an internal offset node. There is no operational difference between the pins.

For proper operation, the AD8210 output offset must not be set with a resistor voltage divider. Any additional external resistance could create a gain error. A low impedance voltage source must be used to set the output offset of the AD8210.

![Figure 31. Split External Reference](ad8210/figures/ad8210-f032.png)

*Figure 31. Split External Reference*

#### Splitting the Supply

By tying one reference pin to V+ and the other to the GND pin, the output is set at midsupply when there is no differential input (see Figure 32). This mode is beneficial because no external reference is required to offset the output for bidirectional current measurement. This creates a midscale offset that is ratiometric to the supply, meaning that if the supply increases or decreases, the output still remains at half scale. For example, if the supply is 5.0 V, the output is at half scale or 2.5 V. If the supply increases by 10% (to 5.5 V), the output also increases by 10% (2.75 V).

![Figure 32. Split Supply](ad8210/figures/ad8210-f033.png)

*Figure 32. Split Supply*

#### INPUT FILTERING

In typical applications, such as motor and solenoid current sensing, filtering at the input of the AD8210 can be beneficial in reducing differential noise, as well as transients and current ripples flowing through the input shunt resistor. An input low-pass filter can be implemented as shown in Figure 33.

The 3 dB frequency for this filter can be calculated by

![Equation as printed (p. 13)](ad8210/figures/ad8210-eq01-recrop.png)

$$f\_3 \, dB = \frac{1}{2 \pi \times 2 \times R_{FILTER} \times C_{FILTER}} \tag{1}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

Adding outside components, such as $R_{FILTER}$ and $C_{FILTER}$, introduces additional errors to the system. To minimize these errors as much as possible, it is recommended that $R_{FILTER}$ be 10 Ω or lower. By adding the $R_{FILTER}$ in series with the 2 kΩ internal input resistors of the AD8210, a gain error is introduced. This can be calculated by

![Equation as printed (p. 13)](ad8210/figures/ad8210-eq02-recrop.png)

$$Gain \ Error ( \% ) = 100 - \left( 100 \times \frac{2 k \Omega}{2 k \Omega - R_{FILTER}} \right) \tag{2}$$

*LaTeX transcription of the equation above, checked against the symbols printed on the page.*

![Figure 33. Input Low-Pass Filtering](ad8210/figures/ad8210-f034.png)

*Figure 33. Input Low-Pass Filtering*

### APPLICATIONS INFORMATION

The AD8210 is ideal for high-side or low-side current sensing. Its accuracy and performance benefits applications, such as 3-phase and H-bridge motor control, solenoid control, and power supply current monitoring.

For solenoid control, two typical circuit configurations are used: high-side current sense with a low-side switch, and high-side current sense with a high-side switch.

#### HIGH-SIDE CURRENT SENSE WITH A LOW-SIDE SWITCH

In this case, the PWM control switch is ground referenced. An inductive load (solenoid) is tied to a power supply. A resistive shunt is placed between the switch and the load (see Figure 34). An advantage of placing the shunt on the high side is that the entire current, including the recirculation current, can be measured because the shunt remains in the loop when the switch is off. In addition, diagnostics can be enhanced because short circuits to ground can be detected with the shunt on the high side.

![Figure 34. Low-Side Switch](ad8210/figures/ad8210-f035.png)

*Figure 34. Low-Side Switch*

In this circuit configuration, when the switch is closed, the common-mode voltage moves down to the negative rail. When the switch is opened, the voltage reversal across the inductive load causes the common-mode voltage to be held one diode drop above the battery by the clamp diode.

#### HIGH-SIDE CURRENT SENSE WITH A HIGH-SIDE SWITCH

This configuration minimizes the possibility of unexpected solenoid activation and excessive corrosion (see Figure 35). In this case, both the switch and the shunt are on the high side. When the switch is off, the battery is removed from the load, which prevents damage from potential short circuits to ground, while still allowing the recirculation current to be measured and diagnostics to be performed. Removing the power supply from the load for the majority of the time minimizes the corrosive effects that could be caused by the differential voltage between the load and ground.

![Figure 35. High-Side Switch](ad8210/figures/ad8210-f036.png)

*Figure 35. High-Side Switch*

Using a high-side switch connects the battery voltage to the load when the switch is closed. This causes the common-mode voltage to increase to the battery voltage. In this case, when the switch is opened, the voltage reversal across the inductive load causes the common-mode voltage to be held one diode drop below ground by the clamp diode.

#### H-BRIDGE MOTOR CONTROL

Another typical application for the AD8210 is as part of the control loop in H-bridge motor control. In this case, the AD8210 is placed in the middle of the H-bridge (see Figure 36) so that it can accurately measure current in both directions by using the shunt available at the motor. This configuration is beneficial for measuring the recirculation current to further enhance the control loop diagnostics.

![Figure 36. Motor Control Application](ad8210/figures/ad8210-f037.png)

*Figure 36. Motor Control Application*

The AD8210 measures current in both directions as the H-bridge switches and the motor changes direction. The output of the AD8210 is configured in an external reference bidirectional mode (see the Modes of Operation section).

### OUTLINE DIMENSIONS

![Figure 37. 8-Lead Standard Small Outline Package (SOIC_N) Narrow Body (R-8) Dimensions shown in millimeters and (inches)](ad8210/figures/ad8210-f038.png)

*Figure 37. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches)*

### ORDERING GUIDE

**Ordering Guide** ([table-06-p15-data.csv](ad8210/tables/table-06-p15-data.csv), p. 15)

| Model $[^{1}]$, $[^{2}]$ | Temperature Range | Package Description | Package Option |
|---|---|---|---|
| AD8210YRZ | −40°C to +125°C | 8-Lead [SOIC_N] | R-8 |
| AD8210YRZ-REEL | −40°C to +125°C | 8-Lead [SOIC_N], 13” Tape and Reel | R-8 |
| AD8210YRZ-REEL7 | −40°C to +125°C | 8-Lead [SOIC_N], 7” Tape and Reel | R-8 |
| AD8210WYRZ | −40°C to +125°C | 8-Lead [SOIC_N] | R-8 |
| AD8210WYRZ-RL | −40°C to +125°C | 8-Lead [SOIC_N], 13” Tape and Reel | R-8 |
| AD8210WYRZ-R7 | −40°C to +125°C | 8-Lead [SOIC_N], 7” Tape and Reel | R-8 |

$[^{1}]$: Z = RoHS Compliant Part.

$[^{2}]$: W = Qualified for Automotive Applications.

### AUTOMOTIVE PRODUCTS

The AD8210W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models.
