---
type: Analog Component
title: "AD620 — Low Cost Low Power Instrumentation Amplifier"
description: "Low Cost Low Power Instrumentation Amplifier"
resource: "https://www.analog.com/en/products/ad620.html"
tags: ["datasheet", "adi"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ad620.pdf"
    title: "AD620 data sheet"
    author: "team:analog-devices"
    last_modified: "7/11"
tables:
  - file: "ad620/tables/table-00-p1-data.csv"
    title: "Table 1. Next Generation Upgrades for AD620"
    page: 1
  - file: "ad620/tables/table-02-p5-abs_max.csv"
    title: "Table 3. (Absolute Maximum Ratings)"
    page: 5
  - file: "ad620/tables/table-03-p13-data.csv"
    title: "Table 4. Make vs. Buy Error Budget"
    page: 13
  - file: "ad620/tables/table-04-p15-data.csv"
    title: "Table 5. Required Values of Gain Resistors"
    page: 15
  - file: "ad620/tables/table-05-p18-pin.csv"
    title: "Table 6. Bond Pad Information"
    page: 18
  - file: "ad620/tables/table-06-p20-data.csv"
    title: "Ordering Guide"
    page: 20
  - file: "ad620/tables/table-01-p3-spec.csv"
    title: "Table 2. (Specifications: Typical @ 25°C, V_{S} = ±15 V, and R_{L} = 2 kΩ, unless otherwise noted.)"
    page: 3
figures:
  - file: "ad620/figures/ad620-f001.png"
    caption: "Figure 1. 8-Lead PDIP (N), CERDIP (Q), and SOIC (R) Packages"
    type: "pinout"
    page: 1
  - file: "ad620/figures/ad620-f002.png"
    caption: "Figure 2. Three Op Amp IA Designs vs. AD620"
    type: "characteristic_curve"
    page: 1
  - file: "ad620/figures/ad620-f004.png"
    caption: "Figure 3. Typical Distribution of Input Offset Voltage"
    type: "characteristic_curve"
    page: 6
  - file: "ad620/figures/ad620-f005.png"
    caption: "Figure 4. Typical Distribution of Input Bias Current"
    type: "characteristic_curve"
    page: 6
  - file: "ad620/figures/ad620-f006.png"
    caption: "Figure 5. Typical Distribution of Input Offset Current"
    type: "characteristic_curve"
    page: 6
  - file: "ad620/figures/ad620-f007.png"
    caption: "Figure 6. Input Bias Current vs. Temperature"
    type: "characteristic_curve"
    page: 6
  - file: "ad620/figures/ad620-f008.png"
    caption: "Figure 7. Change in Input Offset Voltage vs. Warm-Up Time"
    type: "characteristic_curve"
    page: 6
  - file: "ad620/figures/ad620-f009.png"
    caption: "Figure 8. Voltage Noise Spectral Density vs. Frequency (G = 1-1000)"
    type: "characteristic_curve"
    page: 6
  - file: "ad620/figures/ad620-f010.png"
    caption: "Figure 9. Current Noise Spectral Density vs. Frequency"
    type: "characteristic_curve"
    page: 7
  - file: "ad620/figures/ad620-f011.png"
    caption: "Figure 10. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1)"
    type: "scope_capture"
    page: 7
  - file: "ad620/figures/ad620-f012.png"
    caption: "Figure 11. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1000)"
    type: "scope_capture"
    page: 7
  - file: "ad620/figures/ad620-f013.png"
    caption: "Figure 12. 0.1 Hz to 10 Hz Current Noise, 5 pA/Div"
    type: "scope_capture"
    page: 7
  - file: "ad620/figures/ad620-f014.png"
    caption: "Figure 13. Total Drift vs. Source Resistance"
    type: "characteristic_curve"
    page: 7
  - file: "ad620/figures/ad620-f015.png"
    caption: "Figure 14. Typical CMR vs. Frequency, RTI, Zero to 1 kΩ Source Imbalance"
    type: "characteristic_curve"
    page: 7
  - file: "ad620/figures/ad620-f016.png"
    caption: "Figure 15. Positive PSR vs. Frequency, RTI (G = 1-1000)"
    type: "characteristic_curve"
    page: 8
  - file: "ad620/figures/ad620-f017.png"
    caption: "Figure 16. Negative PSR vs. Frequency, RTI (G = 1-1000)"
    type: "characteristic_curve"
    page: 8
  - file: "ad620/figures/ad620-f018.png"
    caption: "Figure 17. Gain vs. Frequency"
    type: "characteristic_curve"
    page: 8
  - file: "ad620/figures/ad620-f019.png"
    caption: "Figure 18. Large Signal Frequency Response"
    type: "characteristic_curve"
    page: 8
  - file: "ad620/figures/ad620-f020.png"
    caption: "Figure 19. Input Voltage Range vs. Supply Voltage, G = 1"
    type: "characteristic_curve"
    page: 8
  - file: "ad620/figures/ad620-f021.png"
    caption: "Figure 20. Output Voltage Swing vs. Supply Voltage, G = 10"
    type: "characteristic_curve"
    page: 8
  - file: "ad620/figures/ad620-f022.png"
    caption: "Figure 21. Output Voltage Swing vs. Load Resistance"
    type: "characteristic_curve"
    page: 9
  - file: "ad620/figures/ad620-f023.png"
    caption: "Figure 22. Large Signal Pulse Response and Settling Time G = 1 (0.5 mV = 0.01%)"
    type: "scope_capture"
    page: 9
  - file: "ad620/figures/ad620-f024.png"
    caption: "Figure 23. Small Signal Response, G = 1, R_{L} = 2 kΩ, C_{L} = 100 pF"
    type: "scope_capture"
    page: 9
  - file: "ad620/figures/ad620-f025.png"
    caption: "Figure 24. Large Signal Response and Settling Time, G = 10 (0.5 mV = 0.01%)"
    type: "scope_capture"
    page: 9
  - file: "ad620/figures/ad620-f026.png"
    caption: "Figure 25. Small Signal Response, G = 10, R_{L} = 2 kΩ, C_{L} = 100 pF"
    type: "scope_capture"
    page: 9
  - file: "ad620/figures/ad620-f027.png"
    caption: "Figure 26. Large Signal Response and Settling Time, G = 100 (0.5 mV = 0.01%)"
    type: "scope_capture"
    page: 9
  - file: "ad620/figures/ad620-f028.png"
    caption: "Figure 27. Small Signal Pulse Response, G = 100, R_{L} = 2 kΩ, C_{L} = 100 pF"
    type: "scope_capture"
    page: 10
  - file: "ad620/figures/ad620-f029.png"
    caption: "Figure 28. Large Signal Response and Settling Time, G = 1000 (0.5 mV = 0.01% )"
    type: "scope_capture"
    page: 10
  - file: "ad620/figures/ad620-f030.png"
    caption: "Figure 29. Small Signal Pulse Response, G = 1000, R_{L} = 2 kΩ, C_{L} = 100 pF"
    type: "scope_capture"
    page: 10
  - file: "ad620/figures/ad620-f031.png"
    caption: "Figure 30. Settling Time vs. Step Size (G = 1)"
    type: "characteristic_curve"
    page: 10
  - file: "ad620/figures/ad620-f032.png"
    caption: "Figure 31. Settling Time to 0.01% vs. Gain, for a 10 V Step"
    type: "characteristic_curve"
    page: 10
  - file: "ad620/figures/ad620-f033.png"
    caption: "Figure 32. Gain Nonlinearity, G = 1, R_{L} = 10 kΩ (10 μV = 1 ppm)"
    type: "scope_capture"
    page: 10
  - file: "ad620/figures/ad620-f034.png"
    caption: "Figure 33. Gain Nonlinearity, G = 100, R_{L} = 10 kΩ (100 μV = 10 ppm)"
    type: "scope_capture"
    page: 11
  - file: "ad620/figures/ad620-f035.png"
    caption: "Figure 34. Gain Nonlinearity, G = 1000, R_{L} = 10 kΩ (1 mV = 100 ppm)"
    type: "scope_capture"
    page: 11
  - file: "ad620/figures/ad620-f036.png"
    caption: "Figure 35. Settling Time Test Circuit"
    type: "test_circuit"
    page: 11
  - file: "ad620/figures/ad620-f037.png"
    caption: "Figure 36. Simplified Schematic of AD620"
    type: "block_diagram"
    page: 12
  - file: "ad620/figures/ad620-f038.png"
    caption: ""
    type: "other"
    page: 13
  - file: "ad620/figures/ad620-f039.png"
    caption: "Figure 37. Make vs. Buy"
    type: "application_circuit"
    page: 13
  - file: "ad620/figures/ad620-f040.png"
    caption: ""
    type: "other"
    page: 13
  - file: "ad620/figures/ad620-f041.png"
    caption: "Figure 38. A Pressure Monitor Circuit that Operates on a 5 V Single Supply"
    type: "application_circuit"
    page: 14
  - file: "ad620/figures/ad620-f042.png"
    caption: "Figure 39. A Medical ECG Monitor Circuit"
    type: "application_circuit"
    page: 14
  - file: "ad620/figures/ad620-f043.png"
    caption: "Figure 40. Precision Voltage-to-Current Converter (Operates on 1.8 mA, ±3 V)"
    type: "application_circuit"
    page: 15
  - file: "ad620/figures/ad620-f044.png"
    caption: "Figure 41. Diode Protection for Voltages Beyond Supply"
    type: "application_circuit"
    page: 15
  - file: "ad620/figures/ad620-f045.png"
    caption: "Figure 42. Circuit to Attenuate RF Interference"
    type: "application_circuit"
    page: 16
  - file: "ad620/figures/ad620-f046.png"
    caption: "Figure 43. Differential Shield Driver"
    type: "application_circuit"
    page: 16
  - file: "ad620/figures/ad620-f047.png"
    caption: "Figure 44. Common-Mode Shield Driver"
    type: "application_circuit"
    page: 16
  - file: "ad620/figures/ad620-f048.png"
    caption: "Figure 45. Basic Grounding Practice"
    type: "application_circuit"
    page: 16
  - file: "ad620/figures/ad620-f049.png"
    caption: "Figure 46. Ground Returns for Bias Currents with Transformer-Coupled Inputs"
    type: "application_circuit"
    page: 17
  - file: "ad620/figures/ad620-f050.png"
    caption: "Figure 47. Ground Returns for Bias Currents with Thermocouple Inputs"
    type: "application_circuit"
    page: 17
  - file: "ad620/figures/ad620-f051.png"
    caption: "Figure 48. Ground Returns for Bias Currents with AC-Coupled Inputs"
    type: "application_circuit"
    page: 17
  - file: "ad620/figures/ad620-f052.png"
    caption: "Figure 49. Bond Pad Diagram"
    type: "pinout"
    page: 18
  - file: "ad620/figures/ad620-f053.png"
    caption: "Figure 50. 8-Lead Plastic Dual In-Line Package [PDIP]"
    type: "other"
    page: 19
  - file: "ad620/figures/ad620-f054.png"
    caption: "Figure 51. 8-Lead Ceramic Dual In-Line Package [CERDIP] (Q-8)"
    type: "other"
    page: 19
  - file: "ad620/figures/ad620-f055.png"
    caption: "Figure 52. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8)"
    type: "other"
    page: 19
  - file: "ad620/figures/ad620-eq01.png"
    caption: "Equation as printed (p. 12)"
    type: equation
    page: 12
  - file: "ad620/figures/ad620-eq02.png"
    caption: "Equation as printed (p. 12)"
    type: equation
    page: 12
  - file: "ad620/figures/ad620-eq04.png"
    caption: "Equation as printed (p. 15)"
    type: equation
    page: 15
  - file: "ad620/figures/ad620-eq05.png"
    caption: "Equation as printed (p. 16)"
    type: equation
    page: 16
  - file: "ad620/figures/ad620-eq06.png"
    caption: "Equation as printed (p. 16)"
    type: equation
    page: 16
  - file: "ad620/figures/ad620-eq03.png"
    caption: "Equation as printed (p. 12)"
    type: equation
    page: 12
curves:
  - file: "ad620/curves/change-in-input-offset-voltage-vs-warm-up-time.csv"
    caption: "Figure 7. Change in Input Offset Voltage vs. Warm-Up Time"
    figure: "ad620/figures/ad620-f008.png"
    page: 6
    x_unit: "Minutes"
    y_unit: "µV"
  - file: "ad620/curves/current-noise-spectral-density-vs-frequency.csv"
    caption: "Figure 9. Current Noise Spectral Density vs. Frequency"
    figure: "ad620/figures/ad620-f010.png"
    page: 7
    x_unit: "Hz"
    y_unit: "fA/√Hz"
  - file: "ad620/curves/gain-vs-frequency.csv"
    caption: "Figure 17. Gain vs. Frequency"
    figure: "ad620/figures/ad620-f018.png"
    page: 8
    x_unit: "Hz"
    y_unit: "V/V"
  - file: "ad620/curves/input-bias-current-vs-temperature.csv"
    caption: "Figure 6. Input Bias Current vs. Temperature"
    figure: "ad620/figures/ad620-f007.png"
    page: 6
    x_unit: "°C"
    y_unit: "nA"
  - file: "ad620/curves/input-voltage-range-vs-supply-voltage-g-1.csv"
    caption: "Figure 19. Input Voltage Range vs. Supply Voltage, G = 1"
    figure: "ad620/figures/ad620-f020.png"
    page: 8
    x_unit: "± Volts"
    y_unit: "V"
  - file: "ad620/curves/large-signal-frequency-response.csv"
    caption: "Figure 18. Large Signal Frequency Response"
    figure: "ad620/figures/ad620-f019.png"
    page: 8
    x_unit: "Hz"
    y_unit: "V p-p"
  - file: "ad620/curves/negative-psr-vs-frequency-rti-g-1-1000.csv"
    caption: "Figure 16. Negative PSR vs. Frequency, RTI (G = 1-1000)"
    figure: "ad620/figures/ad620-f017.png"
    page: 8
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ad620/curves/output-voltage-swing-vs-load-resistance.csv"
    caption: "Figure 21. Output Voltage Swing vs. Load Resistance"
    figure: "ad620/figures/ad620-f022.png"
    page: 9
    x_unit: "Ω"
    y_unit: "V p-p"
    conditions: "V_{S} = ±15V, G = 10"
  - file: "ad620/curves/output-voltage-swing-vs-supply-voltage-g-10.csv"
    caption: "Figure 20. Output Voltage Swing vs. Supply Voltage, G = 10"
    figure: "ad620/figures/ad620-f021.png"
    page: 8
    x_unit: "± Volts"
    y_unit: "V"
  - file: "ad620/curves/positive-psr-vs-frequency-rti-g-1-1000.csv"
    caption: "Figure 15. Positive PSR vs. Frequency, RTI (G = 1-1000)"
    figure: "ad620/figures/ad620-f016.png"
    page: 8
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ad620/curves/settling-time-to-0-01-vs-gain-for-a-10-v-step.csv"
    caption: "Figure 31. Settling Time to 0.01% vs. Gain, for a 10 V Step"
    figure: "ad620/figures/ad620-f032.png"
    page: 10
    x_unit: ""
    y_unit: "µs"
  - file: "ad620/curves/settling-time-vs-step-size-g-1.csv"
    caption: "Figure 30. Settling Time vs. Step Size (G = 1)"
    figure: "ad620/figures/ad620-f031.png"
    page: 10
    x_unit: "V"
    y_unit: "µs"
  - file: "ad620/curves/three-op-amp-ia-designs-vs-ad620.csv"
    caption: "Figure 2. Three Op Amp IA Designs vs. AD620"
    figure: "ad620/figures/ad620-f002.png"
    page: 1
    x_unit: "mA"
    y_unit: "PPM OF FULL SCALE"
  - file: "ad620/curves/total-drift-vs-source-resistance.csv"
    caption: "Figure 13. Total Drift vs. Source Resistance"
    figure: "ad620/figures/ad620-f014.png"
    page: 7
    x_unit: "Ω"
    y_unit: "µV"
  - file: "ad620/curves/typical-cmr-vs-frequency-rti-zero-to-1-k-source-imbalance.csv"
    caption: "Figure 14. Typical CMR vs. Frequency, RTI, Zero to 1 kΩ Source Imbalance"
    figure: "ad620/figures/ad620-f015.png"
    page: 7
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ad620/curves/typical-distribution-of-input-bias-current.csv"
    caption: "Figure 4. Typical Distribution of Input Bias Current"
    figure: "ad620/figures/ad620-f005.png"
    page: 6
    x_unit: "pA"
    y_unit: "%"
    conditions: "SAMPLE SIZE = 850"
  - file: "ad620/curves/typical-distribution-of-input-offset-current.csv"
    caption: "Figure 5. Typical Distribution of Input Offset Current"
    figure: "ad620/figures/ad620-f006.png"
    page: 6
    x_unit: "pA"
    y_unit: "%"
    conditions: "SAMPLE SIZE = 850"
  - file: "ad620/curves/typical-distribution-of-input-offset-voltage.csv"
    caption: "Figure 3. Typical Distribution of Input Offset Voltage"
    figure: "ad620/figures/ad620-f004.png"
    page: 6
    x_unit: "µV"
    y_unit: "%"
    conditions: "SAMPLE SIZE = 360"
  - file: "ad620/curves/voltage-noise-spectral-density-vs-frequency-g-1-1000.csv"
    caption: "Figure 8. Voltage Noise Spectral Density vs. Frequency (G = 1-1000)"
    figure: "ad620/figures/ad620-f009.png"
    page: 6
    x_unit: "Hz"
    y_unit: "nV/√Hz"
agentforge:
  part_number: "AD620"
  datasheet_revision: "H"
  repairs: 1
  reading_order: "geometry"
---

# AD620 — Low Cost Low Power Instrumentation Amplifier

*Datasheet: [AD620 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ad620.pdf)*

### FEATURES
<!-- page: 1 -->

- Easy to use
  - Gain set with one external resistor
  - (Gain range 1 to 10,000)
  - Wide power supply range (±2.3 V to ±18 V)
  - Higher performance than 3 op amp IA designs
  - Available in 8-lead DIP and SOIC packaging
  - Low power, 1.3 mA max supply current
- Excellent dc performance (B grade)
  - 50 µV max, input offset voltage
  - 0.6 µV/°C max, input offset drift
  - 1.0 nA max, input bias current
  - 100 dB min common-mode rejection ratio (G = 10)
- Low noise
  - 9 nV/√Hz @ 1 kHz, input voltage noise
  - 0.28 µV p-p noise (0.1 Hz to 10 Hz)
- Excellent ac specifications
  - 120 kHz bandwidth (G = 100)
  - 15 µs settling time to 0.01%

Digitized data: [three-op-amp-ia-designs-vs-ad620.csv](ad620/curves/three-op-amp-ia-designs-vs-ad620.csv) (x: mA; y: PPM OF FULL SCALE) — values read off the printed plot by the digitizer, not published data.

### APPLICATIONS
<!-- pages: 1-3 -->

Weigh scales

ECG and medical instrumentation 

Transducer interface 

Data acquisition systems 

Industrial process controls 

Battery-powered and portable equipment

**Table 1. Next Generation Upgrades for AD620** ([table-00-p1-data.csv](ad620/tables/table-00-p1-data.csv), p. 1)

| Part | Comment |
|---|---|
| AD8221 | Better specs at lower price |
| AD8222 | Dual channel or differential out |
| AD8226 | Low power, wide input range |
| AD8220 | JFET input |
| AD8228 | Best gain accuracy |
| AD8295 | +2 precision op amps or differential out |
| AD8429 | Ultra low noise |

Rev. H Information  furnished  by  Analog  Devices  is  believed  to  be  accurate  and  reliable. However,  no  responsibility  is  assumed  by  Analog  Devices  for  its  use,  nor  for  any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

### CONNECTION DIAGRAM
<!-- page: 1 -->

![Figure 1. 8-Lead PDIP (N), CERDIP (Q), and SOIC (R) Packages](ad620/figures/ad620-f001.png)

*Figure 1. 8-Lead PDIP (N), CERDIP (Q), and SOIC (R) Packages*

### PRODUCT DESCRIPTION
<!-- page: 1 -->

The AD620 is a low cost, high accuracy instrumentation amplifier that requires only one external resistor to set gains of 1 to 10,000. Furthermore, the AD620 features 8-lead SOIC and DIP packaging that is smaller than discrete designs and offers lower power (only 1.3 mA max supply current), making it a good fit for battery-powered, portable (or remote) applications.

The AD620, with its high accuracy of 40 ppm maximum nonlinearity, low offset voltage of 50 µV max, and offset drift of 0.6 µV/°C max, is ideal for use in precision data acquisition systems, such as weigh scales and transducer interfaces. Furthermore, the low noise, low input bias current, and low power of the AD620 make it well suited for medical applications, such as ECG and noninvasive blood pressure monitors.

The low input bias current of 1.0 nA max is made possible with the use of Superϐeta processing in the input stage. The AD620 works well as a preamplifier due to its low input voltage noise of 9 nV/√Hz at 1 kHz, 0.28 µV p-p in the 0.1 Hz to 10 Hz band, and 0.1 pA/√Hz input current noise. Also, the AD620 is well suited for multiplexed applications with its settling time of 15 µs to 0.01%, and its cost is low enough to enable designs with one in-amp per channel.

![Figure 2. Three Op Amp IA Designs vs. AD620](ad620/figures/ad620-f002.png)

*Figure 2. Three Op Amp IA Designs vs. AD620*

### TABLE OF CONTENTS

- Specifications
- Absolute Maximum Ratings
  - ESD Caution
- Typical Performance Characteristics
- Theory of Operation
 - Gain Selection
 - Input and Output Offset Voltage
 - Reference Terminal
 - Input Protection
 - RF Interference
 - Common-Mode Rejection
 - Grounding
 - Ground Returns for Input Bias Currents
- AD620ACHIPS Information
- Outline Dimensions
 - Ordering Guide
 
### REVISION HISTORY 
- 7/11—Rev. G to Rev. H 
- Deleted Figure 3
- Added Table 1
- Moved Figure 2
- Added ESD Input Diodes to Simplified Schematic
- Changes to Input Protection Section
- Added Figure 41; Renumbered Sequentially
- Changes to AD620ACHIPS Information Section
- Updated Ordering Guide
 
### 12/04—Rev. F to Rev. G 
- Updated Format
- Change to Features
- Change to Product Description
- Changes to Specifications
- Added Metallization Photograph
- Replaced Figure 4-Figure 6
- Replaced Figure 15
- Replaced Figure 33
- Replaced Figure 34 and Figure 35
- Replaced Figure 37
- Changes to Table 3
- Changes to Figure 41 and Figure 42
- Changes to Figure 43
- Change to Figure 44
- Changes to Input Protection section
- Deleted Figure 9
- Changes to RF Interference section
- Edit to Ground Returns for Input Bias Currents section
- Added AD620CHIPS to Ordering Guide

 ### 7/03—Data Sheet Changed from Rev. E to Rev. F 
- Edit to FEATURES
- Changes to SPECIFICATIONS
- Removed AD620CHIPS from ORDERING GUIDE
- Removed METALLIZATION PHOTOGRAPH
- Replaced TPCs 1–3
- Replaced TPC 12
- Replaced TPC 30
- Replaced TPCs 31 and 32
- Replaced Figure 4
- Changes to Table I
- Changes to Figures 6 and 7
- Changes to Figure 8
- Edited INPUT PROTECTION section
- Added new Figure 9
- Changes to RF INTERFACE section
- Edit to GROUND RETURNS FOR INPUT BIAS CURRENTS section
- Updated OUTLINE DIMENSIONS

### SPECIFICATIONS
<!-- pages: 3-5 -->

Typical @ 25°C, V_{S} = ±15 V , and R_{L} = 2 kΩ, unless otherwise noted. Table 2.

|                              |                              | AD620A                | AD620A          | AD620A                | AD620B                | AD620B          | AD620B                | AD620S[^1]               | AD620S[^1]         | AD620S[^1]               |          |
|------------------------------|------------------------------|-----------------------|-----------------|-----------------------|-----------------------|-----------------|-----------------------|-----------------------|-----------------|-----------------------|----------|
| Parameter                    | Conditions                   | Min                   | Typ             | Max                   | Min                   | Typ             | Max                   | Min                   | Typ             | Max                   | Unit     |
| GAIN                         | G = 1 + (49.4 kΩ/R_{G})        |                       |                 |                       |                       |                 |                       |                       |                 |                       |          |
| Gain Range                   |                              | 1                     |                 | 10,000                | 1                     |                 | 10,000                | 1                     |                 | 10,000                |          |
| Gain Error[^2]                  | V_{OUT} = ±10 V                |                       |                 |                       |                       |                 |                       |                       |                 |                       |          |
| G = 1                        |                              |                       | 0.03            | 0.10                  |                       | 0.01            | 0.02                  |                       | 0.03            | 0.10                  | %        |
| G = 10                       |                              |                       | 0.15            | 0.30                  |                       | 0.10            | 0.15                  |                       | 0.15            | 0.30                  | %        |
| G = 100                      |                              |                       | 0.15            | 0.30                  |                       | 0.10            | 0.15                  |                       | 0.15            | 0.30                  | %        |
| G = 1000                     |                              |                       | 0.40            | 0.70                  |                       | 0.35            | 0.50                  |                       | 0.40            | 0.70                  | %        |
| Nonlinearity                 | V_{OUT} = -10 V to +10 V       |                       |                 |                       |                       |                 |                       |                       |                 |                       |          |
| G = 1-1000                   | R_{L} = 10 kΩ                  |                       | 10              | 40                    |                       | 10              | 40                    |                       | 10              | 40                    | ppm      |
| G = 1-100                    | R_{L} = 2 kΩ                   |                       | 10              | 95                    |                       | 10              | 95                    |                       | 10              | 95                    | ppm      |
| Gain vs. Temperature         |                              |                       |                 | 10                    |                       |                 |                       |                       |                 |                       |          |
|                              | G = 1                        |                       |                 |                       |                       |                 | 10                    |                       |                 | 10                    | ppm/°C   |
|                              | Gain >1[^2]                     |                       |                 | -50                   |                       |                 | -50                   |                       |                 | -50                   | ppm/°C   |
| VOLTAGE OFFSET               | (Total RTI Error = V_{OSI} + V_{OSO} /G)                 |                 |                       |                       |                 |                       |                       |                 |                       |          |
| Input Offset, V_{OSI}          | V_{S} = ±5 V to ± 15 V         |                       | 30              | 125                   |                       | 15              | 50                    |                       | 30              | 125                   | µV       |
| Overtemperature              | V_{S} = ±5 V to ± 15 V         |                       |                 | 185                   |                       |                 | 85                    |                       |                 | 225                   | µV       |
| Average TC                   | V_{S} = ±5 V to ± 15 V         |                       | 0.3             | 1.0                   |                       | 0.1             | 0.6                   |                       | 0.3             | 1.0                   | µV/°C    |
| Output Offset, V_{OSO}         | V_{S} = ±15 V                  |                       | 400             | 1000                  |                       | 200             | 500                   |                       | 400             | 1000                  | µV     |
|                              | V_{S} = ± 5 V                  |                       |                 | 1500                  |                       |                 | 750                   |                       |                 | 1500                  | µV|
| Overtemperature              | V_{S} = ±5 V to ± 15 V         |                       |                 | 2000                  |                       |                 | 1000                  |                       |                 | 2000                  | µV       |
| Average TC                   | V_{S} = ±5 V to ± 15 V         |                       | 5.0             | 15                    |                       | 2.5             | 7.0                   |                       | 5.0             | 15                    | µV/°C    |
| Offset Referred to the (PSR) Input vs. Supply | V_{S} = ±2.3 V to ±18 V        |                       |                 |                       |                       |                 |                       |                       |                 |                       |          |
| G = 1                        |                              | 80                    | 100             |                       | 80                    | 100             |                       | 80                    | 100             |                       | dB       |
| G = 10                       |                              | 95                    | 120             |                       | 100                   | 120             |                       | 95                    | 120             |                       | dB       |
| G = 100                      |                              | 110                   | 140             |                       | 120                   | 140             |                       | 110                   | 140             |                       | dB       |
| G = 1000                     |                              | 110                   | 140             |                       | 120                   | 140             |                       | 110                   | 140             |                       | dB       |
| INPUT CURRENT                |                              |                       |                 |                       |                       |                 |                       |                       |                 |                       |          |
| Input Bias Current           |                              |                       | 0.5             | 2.0                   |                       | 0.5             | 1.0                   |                       | 0.5             | 2                     | nA       |
| Overtemperature              |                              |                       |                 | 2.5                   |                       |                 | 1.5                   |                       |                 | 4                     | nA       |
| Average TC                   |                              |                       | 3.0             |                       |                       | 3.0             |                       |                       | 8.0             |                       | pA/°C    |
| Input Offset Current         |                              |                       | 0.3             | 1.0                   |                       | 0.3             | 0.5                   |                       | 0.3             | 1.0                   | nA       |
| Overtemperature Average TC   |                              |                       | 1.5             | 1.5                   |                       | 1.5             | 0.75                  |                       | 8.0             | 2.0                   | nA pA/°C |
| INPUT                        |                              |                       |                 |                       |                       |                 |                       |                       |                 |                       |          |
| Input Impedance Differential |                              |                       | 10||2           |                       |                       | 10||2           |                       |                       | 10||2           |                       | GΩ_pF    |
| Common-Mode                  |                              |                       | 10||2           |                       |                       | 10||2           |                       |                       | 10||2           |                       | GΩ_pF    |
| Input Voltage Range[^3]         | V_{S} = ±2.3 V to ±5 V         | -V_{S} + 1.9            |                 | +V_{S} - 1.2            | -V_{S} + 1.9            |                 | +V_{S} - 1.2            | -V_{S} + 1.9            |                 | +V_{S} - 1.2            | V        |
| Overtemperature              | V_{S} = ± 5 V to ±18 V         | -V_{S} + 2.1            |                 | +V_{S} - 1.3            | -V_{S} + 2.1            |                 | +V_{S} - 1.3            | -V_{S} + 2.1            |                 | +V_{S} - 1.3            | V      |
|                              |                              | -V_{S} + 1.9            |                 | +V_{S} - 1.4            | -V_{S} + 1.9            |                 | +V_{S} - 1.4            | -V_{S} + 1.9            |                 | +V_{S} - 1.4            | V|
| Overtemperature              |                              | -V_{S} + 2.1            |                 | +V_{S} - 1.4            | -V_{S} + 2.1            |                 | +V_{S} + 2.1            | -V_{S} + 2.3            |                 | +V_{S} - 1.4            | V        |

|                              |                                   | AD620A         | AD620A         | AD620A     | AD620B     | AD620B   | AD620B     | AD620S[^1]     | AD620S[^1]    | AD620S[^1]    |        |
|------------------------------|-----------------------------------|----------------|----------------|------------|------------|----------|------------|-------------|------------|------------|--------|
| Parameter                    | Conditions                        | Min            | Typ            | Max        | Min        | Typ      | Max        | Min         | Typ        | Max        | Unit   |
| Common-Mode Rejection        |                                   |                |                |            |            |          |            |             |            |            |        |
| Ratio DC to 60 Hz with  1 kΩ Source Imbalance     |    V_{CM} = 0 V to ± 10 V                               |                |                |            |            |          |            |             |            |            |        |
| G = 1                        |                                   | 73             | 90             |            | 80         | 90       |            | 73          | 90         |            | dB     |
| G = 10                       |                                   | 93             | 110            |            | 100        | 110      |            | 93          | 110        |            | dB     |
| G = 100                      |                                   | 110            | 130            |            | 120        | 130      |            | 110         | 130        |            | dB     |
| G = 1000                     |                                   | 110            | 130            |            | 120        | 130      |            | 110         | 130        |            | dB     |
| OUTPUT                       |                                   |                |                |            |            |          |            |             |            |            |        |
| Output Swing                 | R_{L} = 10 kΩ                       |                |                |            |            |          |            |             |            |            |        |
|                              | V_{S} = ±2.3 V to ± 5 V             | -V_{S} + 1.1     |                | +V_{S} - 1.2 | -V_{S} + 1.1 |          | +V_{S} - 1.2 | -V_{S} + 1.1  |            | +V_{S} - 1.2 | V      |
| Overtemperature              |                                   | -V_{S} + 1.4     |                | +V_{S} - 1.3 | -V_{S} + 1.4 |          | +V_{S} - 1.3 | -V_{S} + 1.6  |            | +V_{S} - 1.3 | V      |
|                              | V_{S} = ±5 V  to ± 18 V             | -V_{S} + 1.2     |                | +V_{S} - 1.4 | -V_{S} + 1.2 |          | +V_{S} - 1.4 | -V_{S} + 1.2  |            | +V_{S} - 1.4 | V      |
| Overtemperature              |                                   | -V_{S} + 1.6     |                | +V_{S} - 1.5 | -V_{S} + 1.6 |          | +V_{S} - 1.5 | -V_{S} + 2.3  |            | +V_{S} - 1.5 | V      |
| Short Circuit Current        |                                   |                | ±18            |            |            | ±18      |            |             | ±18        |            |        |mA|
| DYNAMIC RESPONSE             |                                   |                |                |            |            |          |            |             |            |            |        |
| Small Signal -3 dB Bandwidth |                                   |                |                |            |            |          |            |             |            |            |        |
| G = 1                        |                                   |                | 1000           |            |            | 1000     |            |             | 1000       |            | kHz    |
| G = 10                       |                                   |                | 800            |            |            | 800      |            |             | 800        |            | kHz    |
| G = 100                      |                                   |                | 120            |            |            | 120      |            |             | 120        |            | kHz    |
| G = 1000                     |                                   |                | 12             |            |            | 12       |            |             | 12         |            | kHz    |
| Slew Rate                    |                                   | 0.75           | 1.2            |            | 0.75       | 1.2      |            | 0.75        | 1.2        |            | V/µs   |
| Settling Time to 0.01%       | 10 V Step                         |                |                |            |            |          |            |             |            |            |        |
| G = 1-100                    |                                   |                | 15             |            |            | 15       |            |             | 15         |            | µs     |
| G = 1000                     |                                   |                | 150            |            |            | 150      |            |             | 150        |            | µs     |
| NOISE                        |                                   |                |                |            |            |          |            |             |            |            |        |
| Voltage Noise, 1 kHz         | Total RTI Noise = √(e^{2}_{ni}) + (e_{no}/G)^{2}             |                |                |            |            |          |            |             |            |            |        |
| Input, Voltage Noise, e_{ni}   |                                   | 9              |                | 13         |            | 9        | 13         |             | 9          | 13         | nV/√Hz |
| Output, Voltage Noise, e_{no}  |                                   |                | 72             | 100        |            | 72       | 100        |             | 72         | 100        | nV/√Hz |
| RTI, 0.1 Hz to 10 Hz         |                                   |                |                |            |            |          |            |             |            |            |        |
| G = 1                        |                                   |                | 3.0            |            |            | 3.0      | 6.0        |             | 3.0        | 6.0        | µV p-p |
| G = 10                       |                                   |                | 0.55           |            |            | 0.55     | 0.8        |             | 0.55       | 0.8        | µV p-p |
| G = 100-1000                 |                                   |                | 0.28           |            |            | 0.28     | 0.4        |             | 0.28       | 0.4        | µV p-p |
| Current Noise                | f = 1 kHz                         |                | 100            |            |            | 100      |            |             | 100        |            | fA/√Hz |
| 0.1 Hz to 10 Hz              |                                   |                | 10             |            |            | 10       |            |             | 10         |            | pA p-p |
| REFERENCE INPUT              |                                   |                |                |            |            |          |            |             |            |            |        |
| R IN                         |                                   |                | 20             |            |            | 20       |            |             | 20         |            | kΩ     |
| I IN                         | V_{IN+} , V_{REF} = 0                 |                | 50             | 60         |            | 50       | 60         |             | 50         | 60         | µA     |
| Voltage Range                |                                   | -V_{S} + 1.6     |                | +V_{S} - 1.6 | -V_{S} + 1.6 |          | +V_{S} - 1.6 | -V_{S} + 1.6  |            | +V_{S} - 1.6 | V      |
| Gain to Output               |                                   | 1 ± 0.0001     |                |            | 1 ± 0.0001 |          |            | 1 ± 0.0001  |            |            |        |
| POWER SUPPLY                 |                                   |                |                |            |            |          |            |             |            |            |        |
| Operating Range[^4]            |                                   | ±2.3           |                | ±18        | ±2.3       |          | ±18        | ±2.3        |            | ±18        | V      |
| Quiescent Current            | V_{S} = ±2.3 V                      |                | 0.9            | 1.3        |            | 0.9      | 1.3        |             | 0.9        | 1.3        | mA     |
| Overtemperature              |                                   |                | 1.1            | 1.6        |            | 1.1      | 1.6        |             | 1.1        | 1.6        | mA     |
| TEMPERATURE RANGE            |                                   |                |                |            |            |          |            |             |            |            |        |
| For Specified Performance    |                                   | -40 to +85     |                |            | -40 to +85 |          |            | -55 to +125 |            |            | °C     |

- **Note 1:** See Analog Devices military data sheet for 883B tested specifications.
- **Note 2:** Does not include effects of external resistor R_{G}.
- **Note 3:** One input grounded. G = 1.
- **Note 4:** This is defined as the same supply range that is used to specify PSR.

### ABSOLUTE MAXIMUM RATINGS
<!-- page: 5 -->

**Table 3. (Absolute Maximum Ratings)** ([table-02-p5-abs_max.csv](ad620/tables/table-02-p5-abs_max.csv), p. 5)

| PARAMETER | RATING |
|---|---|
| Supply Voltage | ±18 V |
| Internal Power Dissipation[^1] | 650 mW |
| Input Voltage (Common-Mode) | ±V_{S} |
| Differential Input Voltage | 25 V |
| Output Short-Circuit Duration | Indefinite |
| Storage Temperature Range (Q) | −65°C to +150°C |
| Storage Temperature Range (N, R) | −65°C to +125°C |
| **Operating Temperature Range** |  |
| AD620 (A, B) | −40°C to +85°C |
| AD620 (S) | −55°C to +125°C |
| **Lead Temperature Range** |  |
| (Soldering 10 seconds) | 300°C |

- **Note 1:** Specification is for device in free air: 

    8-Lead Plastic Package: θ_{JA} = 95°C

    8-Lead CERDIP Package: θ_{JA} = 110°C 

    8-Lead SOIC Package: θ_{JA} = 155°C

Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other condition s above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

### ESD CAUTION
<!-- pages: 5-6 -->

![Figure 56. (ad620/figures/ad620-f056.png)

### TYPICAL PERFORMANCE CHARACTERISTICS
<!-- pages: 6-12 -->

(@ 25°C, V_{S} = ±15 V , R_{L} = 2 kΩ, unless otherwise noted.)

![Figure 3. Typical Distribution of Input Offset Voltage](ad620/figures/ad620-f004.png)

*Figure 3. Typical Distribution of Input Offset Voltage*

Digitized data: [typical-distribution-of-input-offset-voltage.csv](ad620/curves/typical-distribution-of-input-offset-voltage.csv) (x: µV; y: %) — values read off the printed plot by the digitizer, not published data.

![Figure 4. Typical Distribution of Input Bias Current](ad620/figures/ad620-f005.png)

*Figure 4. Typical Distribution of Input Bias Current*

Digitized data: [typical-distribution-of-input-bias-current.csv](ad620/curves/typical-distribution-of-input-bias-current.csv) (x: pA; y: %) — values read off the printed plot by the digitizer, not published data.

![Figure 5. Typical Distribution of Input Offset Current](ad620/figures/ad620-f006.png)

*Figure 5. Typical Distribution of Input Offset Current*

Digitized data: [typical-distribution-of-input-offset-current.csv](ad620/curves/typical-distribution-of-input-offset-current.csv) (x: pA; y: %) — values read off the printed plot by the digitizer, not published data.

![Figure 6. Input Bias Current vs. Temperature](ad620/figures/ad620-f007.png)

*Figure 6. Input Bias Current vs. Temperature*

Digitized data: [input-bias-current-vs-temperature.csv](ad620/curves/input-bias-current-vs-temperature.csv) (x: °C; y: nA) — values read off the printed plot by the digitizer, not published data.

![Figure 7. Change in Input Offset Voltage vs. Warm-Up Time](ad620/figures/ad620-f008.png)

*Figure 7. Change in Input Offset Voltage vs. Warm-Up Time*

Digitized data: [change-in-input-offset-voltage-vs-warm-up-time.csv](ad620/curves/change-in-input-offset-voltage-vs-warm-up-time.csv) (x: Minutes; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 8. Voltage Noise Spectral Density vs. Frequency (G = 1-1000)](ad620/figures/ad620-f009.png)

*Figure 8. Voltage Noise Spectral Density vs. Frequency (G = 1-1000)*

Digitized data: [voltage-noise-spectral-density-vs-frequency-g-1-1000.csv](ad620/curves/voltage-noise-spectral-density-vs-frequency-g-1-1000.csv) (x: Hz; y: nV/√Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 9. Current Noise Spectral Density vs. Frequency](ad620/figures/ad620-f010.png)

*Figure 9. Current Noise Spectral Density vs. Frequency*

Digitized data: [current-noise-spectral-density-vs-frequency.csv](ad620/curves/current-noise-spectral-density-vs-frequency.csv) (x: Hz; y: f_{A}/√Hz) — values read off the printed plot by the digitizer, not published data.

![Figure 10. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1)](ad620/figures/ad620-f011.png)

*Figure 10. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1)*

![Figure 11. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1000)](ad620/figures/ad620-f012.png)

*Figure 11. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1000)*

![Figure 12. 0.1 Hz to 10 Hz Current Noise, 5 pA/Div](ad620/figures/ad620-f013.png)

*Figure 12. 0.1 Hz to 10 Hz Current Noise, 5 pA/Div*

![Figure 13. Total Drift vs. Source Resistance](ad620/figures/ad620-f014.png)

*Figure 13. Total Drift vs. Source Resistance*

Digitized data: [total-drift-vs-source-resistance.csv](ad620/curves/total-drift-vs-source-resistance.csv) (x: Ω; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 14. Typical CMR vs. Frequency, RTI, Zero to 1 kΩ Source Imbalance](ad620/figures/ad620-f015.png)

*Figure 14. Typical CMR vs. Frequency, RTI, Zero to 1 kΩ Source Imbalance*

Digitized data: [typical-cmr-vs-frequency-rti-zero-to-1-k-source-imbalance.csv](ad620/curves/typical-cmr-vs-frequency-rti-zero-to-1-k-source-imbalance.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 15. Positive PSR vs. Frequency, RTI (G = 1-1000)](ad620/figures/ad620-f016.png)

*Figure 15. Positive PSR vs. Frequency, RTI (G = 1-1000)*

Digitized data: [positive-psr-vs-frequency-rti-g-1-1000.csv](ad620/curves/positive-psr-vs-frequency-rti-g-1-1000.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 16. Negative PSR vs. Frequency, RTI (G = 1-1000)](ad620/figures/ad620-f017.png)

*Figure 16. Negative PSR vs. Frequency, RTI (G = 1-1000)*

Digitized data: [negative-psr-vs-frequency-rti-g-1-1000.csv](ad620/curves/negative-psr-vs-frequency-rti-g-1-1000.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 17. Gain vs. Frequency](ad620/figures/ad620-f018.png)

*Figure 17. Gain vs. Frequency*

Digitized data: [gain-vs-frequency.csv](ad620/curves/gain-vs-frequency.csv) (x: Hz; y: V/V) — values read off the printed plot by the digitizer, not published data.

![Figure 18. Large Signal Frequency Response](ad620/figures/ad620-f019.png)

*Figure 18. Large Signal Frequency Response*

Digitized data: [large-signal-frequency-response.csv](ad620/curves/large-signal-frequency-response.csv) (x: Hz; y: V p-p) — values read off the printed plot by the digitizer, not published data.

![Figure 19. Input Voltage Range vs. Supply Voltage, G = 1](ad620/figures/ad620-f020.png)

*Figure 19. Input Voltage Range vs. Supply Voltage, G = 1*

Digitized data: [input-voltage-range-vs-supply-voltage-g-1.csv](ad620/curves/input-voltage-range-vs-supply-voltage-g-1.csv) (x: ± Volts; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 20. Output Voltage Swing vs. Supply Voltage, G = 10](ad620/figures/ad620-f021.png)

*Figure 20. Output Voltage Swing vs. Supply Voltage, G = 10*

Digitized data: [output-voltage-swing-vs-supply-voltage-g-10.csv](ad620/curves/output-voltage-swing-vs-supply-voltage-g-10.csv) (x: ± Volts; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 21. Output Voltage Swing vs. Load Resistance](ad620/figures/ad620-f022.png)

*Figure 21. Output Voltage Swing vs. Load Resistance*

Digitized data: [output-voltage-swing-vs-load-resistance.csv](ad620/curves/output-voltage-swing-vs-load-resistance.csv) (x: Ω; y: V p-p) — values read off the printed plot by the digitizer, not published data.

![Figure 22. Large Signal Pulse Response and Settling Time G = 1 (0.5 mV = 0.01%)](ad620/figures/ad620-f023.png)

*Figure 22. Large Signal Pulse Response and Settling Time G = 1 (0.5 mV = 0.01%)*

![Figure 23. Small Signal Response, G = 1, R_{L} = 2 kΩ, C_{L} = 100 pF](ad620/figures/ad620-f024.png)

*Figure 23. Small Signal Response, G = 1, R_{L} = 2 kΩ, C_{L} = 100 pF*

![Figure 24. Large Signal Response and Settling Time, G = 10 (0.5 mV = 0.01%)](ad620/figures/ad620-f025.png)

*Figure 24. Large Signal Response and Settling Time, G = 10 (0.5 mV = 0.01%)*

![Figure 25. Small Signal Response, G = 10, R_{L} = 2 kΩ, C_{L} = 100 pF](ad620/figures/ad620-f026.png)

*Figure 25. Small Signal Response, G = 10, R_{L} = 2 kΩ, C_{L} = 100 pF*

![Figure 26. Large Signal Response and Settling Time, G = 100 (0.5 mV = 0.01%)](ad620/figures/ad620-f027.png)

*Figure 26. Large Signal Response and Settling Time, G = 100 (0.5 mV = 0.01%)*

![Figure 27. Small Signal Pulse Response, G = 100, R_{L} = 2 kΩ, C_{L} = 100 pF](ad620/figures/ad620-f028.png)

*Figure 27. Small Signal Pulse Response, G = 100, R_{L} = 2 kΩ, C_{L} = 100 pF*

![Figure 28. Large Signal Response and Settling Time, G = 1000 (0.5 mV = 0.01% )](ad620/figures/ad620-f029.png)

*Figure 28. Large Signal Response and Settling Time, G = 1000 (0.5 mV = 0.01% )*

![Figure 29. Small Signal Pulse Response, G = 1000, R_{L} = 2 kΩ, C_{L} = 100 pF](ad620/figures/ad620-f030.png)

*Figure 29. Small Signal Pulse Response, G = 1000, R_{L} = 2 kΩ, C_{L} = 100 pF*

![Figure 30. Settling Time vs. Step Size (G = 1)](ad620/figures/ad620-f031.png)

*Figure 30. Settling Time vs. Step Size (G = 1)*

Digitized data: [settling-time-vs-step-size-g-1.csv](ad620/curves/settling-time-vs-step-size-g-1.csv) (x: V; y: µs) — values read off the printed plot by the digitizer, not published data.

![Figure 31. Settling Time to 0.01% vs. Gain, for a 10 V Step](ad620/figures/ad620-f032.png)

*Figure 31. Settling Time to 0.01% vs. Gain, for a 10 V Step*

Digitized data: [settling-time-to-0-01-vs-gain-for-a-10-v-step.csv](ad620/curves/settling-time-to-0-01-vs-gain-for-a-10-v-step.csv) (x: ; y: µs) — values read off the printed plot by the digitizer, not published data.

![Figure 32. Gain Nonlinearity, G = 1, R_{L} = 10 kΩ (10 µV = 1 ppm)](ad620/figures/ad620-f033.png)

*Figure 32. Gain Nonlinearity, G = 1, R_{L} = 10 kΩ (10 µV = 1 ppm)*

![Figure 33. Gain Nonlinearity, G = 100, R_{L} = 10 kΩ (100 µV = 10 ppm)](ad620/figures/ad620-f034.png)

*Figure 33. Gain Nonlinearity, G = 100, R_{L} = 10 kΩ (100 µV = 10 ppm)*

![Figure 34. Gain Nonlinearity, G = 1000, R_{L} = 10 kΩ (1 mV = 100 ppm)](ad620/figures/ad620-f035.png)

*Figure 34. Gain Nonlinearity, G = 1000, R_{L} = 10 kΩ (1 mV = 100 ppm)*

![Figure 35. Settling Time Test Circuit](ad620/figures/ad620-f036.png)

*Figure 35. Settling Time Test Circuit*

### THEORY OF OPERATION
<!-- pages: 12-14 -->

![Figure 36. Simplified Schematic of AD620](ad620/figures/ad620-f037.png)

*Figure 36. Simplified Schematic of AD620*

The AD620 is a monolithic instrumentation amplifier based on a modification of the classic three op amp approach. Absolute value trimming allows the user to program gain accurately (to 0.15% at G = 100) with only one resistor. Monolithic construction and laser wafer trimming allow the tight matching and tracking of circuit components, thus ensuring the high level of performance inherent in this circuit.

The input transistors Q1 and Q2 provide a single differentialpair bipolar input for high precision (Figure 36), yet offer 10× lower input bias current thanks to Superϐeta processing. Feedback through the Q1-A1-R1 loop and the Q2-A2-R2 loop maintains constant collector current of the input devices Q1 and Q2, thereby impressing the input voltage across the external gain setting resistor R_{G} . This creates a differential gain from the inputs to the A1/A2 outputs given by G = ( R1 + R2 )/ R_{G} + 1. The unity-gain subtractor, A3, removes any common-mode signal, yielding a single-ended output referred to the REF pin potential.

The value of R_{G} also determines the transconductance of the preamp stage. As R_{G} is reduced for larger gains, the transconductance increases asymptotically to that of the input transistors. This has three important advantages: (a) Open-loop gain is boosted for increasing programmed gain, thus reducing gain related errors. (b) The gain-bandwidth product (determined by C1 and C2 and the preamp transconductance) increases with programmed gain, thus optimizing frequency response. (c) The input voltage noise is reduced to a value of 9 nV/√Hz, determined mainly by the collector current and base resistance of the input devices.

The internal gain resistors, R1 and R2, are trimmed to an absolute value of 24.7 kΩ, allowing the gain to be programmed accurately with a single external resistor.

The gain equation is then

$$G = \frac{49.4 k \Omega}{R_{G}} + 1$$

$$R_{G} = \frac{49.4 k \Omega}{G - 1}$$

### Make vs. Buy: a Typical Bridge Application Error Budget
<!-- page: 12 -->

The AD620 offers improved performance over 'homebrew' three op amp IA designs, along with smaller size, fewer components, and 10× lower supply current. In the typical application, shown in Figure 37, a gain of 100 is required to amplify a bridge output of 20 mV full-scale over the industrial temperature range of -40°C to +85°C. Table 4 shows how to calculate the effect various error sources have on circuit accuracy.

Regardless of the system in which it is being used, the AD620 provides greater accuracy at low power and price. In simple systems, absolute accuracy and drift errors are by far the most significant contributors to error. In more complex systems with an intelligent processor, an autogain/autozero cycle removes all absolute accuracy and drift errors, leaving only the resolution errors of gain, nonlinearity, and noise, thus allowing full 14-bit accuracy.

Note that for the homebrew circuit, the OP07 specifications for input voltage offset and noise have been multiplied by √2. This is because a three op amp type in-amp has two op amps at its inputs, both contributing to the overall input error.

![Figure 37. Make vs. Buy](ad620/figures/ad620-f039.png)

*Figure 37. Make vs. Buy*

**Table 4. Make vs. Buy Error Budget** ([table-03-p13-data.csv](ad620/tables/table-03-p13-data.csv), p. 13)

| Error Source | AD620 Circuit Calculation | "Homebrew" Circuit Calculation | Error, ppm of Full Scale AD620 | Error, ppm of Full Scale Homebrew |
|---|---|---|---|---|
| **ABSOLUTE ACCURACY at T_{A} = 25°C** |  |  |  |  |
| Input Offset Voltage, µV | 125 µV/20 mV | (150 µV × √2)/20 mV | 6,250 | 10,607 |
| Output Offset Voltage, µV | 1000 µV/100 mV/20 mV | ((150 µV × 2)/100)/20 mV | 500 | 150 |
| Input Offset Current, nA | 2 nA ×350 Ω/20 mV | (6 nA ×350 Ω)/20 mV | 18 | 53 |
| CMR, dB | 110 dB(3.16 ppm) ×5 V/20 mV | (0.02% Match × 5 V)/20 mV/100 | 791 | 500 |
| | | Total Absolute Error | 7,559 | 11,310 |
| **DRIFT TO 85°C** |  |  |  |  |
| Gain Drift, ppm/°C | (50 ppm + 10 ppm) ×60°C | 100 ppm/°C Track × 60°C | 3,600 | 6,000 |
| Input Offset Voltage Drift, µV/°C | 1 µV/°C × 60°C/20 mV | (2.5 µV/°C × √2 × 60°C)/20 mV | 3,000 | 10,607 |
| Output Offset Voltage Drift, µV/°C | 15 µV/°C × 60°C/100 mV/20 mV | (2.5 µV/°C × 2 × 60°C)/100 mV/20 mV | 450 | 150 |
| | | Total Drift Error | 7,050 | 16,757 |
| **RESOLUTION** |  |  |  |  |
| Gain Nonlinearity, ppm of Full Scale | 40 ppm | 40 ppm | 40 | 40 |
| Typ 0.1 Hz to 10 Hz Voltage Noise, µV p-p | 0.28 µV p-p/20 mV | (0.38 µV p-p × √2)/20 mV | 14 | 27 |
| Typ 0.1 Hz to 10 Hz Voltage Noise, µV p-p | 0.28 µV p-p/20 mV | Total Resolution Error | 54 | 67 |
| | | Grand Total Error | 14,663 | 28,134 |

- G = 100, V_{S} = ±15 V.
- (All errors are min/max and referred to input.)

![Figure 38. A Pressure Monitor Circuit that Operates on a 5 V Single Supply](ad620/figures/ad620-f041.png)

*Figure 38. A Pressure Monitor Circuit that Operates on a 5 V Single Supply*

### Pressure Measurement
<!-- pages: 14-15 -->

Although useful in many bridge applications, such as weigh scales, the AD620 is especially suitable for higher resistance pressure sensors powered at lower voltages where small size and low power become more significant.

Figure 38 shows a 3 kΩ pressure transducer bridge powered from 5 V. In such a circuit, the bridge consumes only 1.7 mA. Adding the AD620 and a buffered voltage divider allows the signal to be conditioned for only 3.8 mA of total supply current.

Small size and low cost make the AD620 especially attractive for voltage output pressure transducers. Since it delivers low noise and drift, it also serves applications such as diagnostic noninvasive blood pressure measurement.

### Medical ECG
<!-- page: 14 -->

The low current noise of the AD620 allows its use in ECG monitors (Figure 39) where high source resistances of 1 MΩ or higher are not uncommon. The AD620's low power, low supply voltage requirements, and space-saving 8-lead mini-DIP and SOIC package offerings make it an excellent choice for batterypowered data recorders.

Furthermore, the low bias currents and low current noise, coupled with the low voltage noise of the AD620, improve the dynamic range for better performance.

The value of capacitor C1 is chosen to maintain stability of the right leg drive loop. Proper safeguards, such as isolation, must be added to this circuit to protect the patient from possible harm.


![Figure 39. A Medical ECG Monitor Circuit](ad620/figures/ad620-f042.png)

*Figure 39. A Medical ECG Monitor Circuit*

### Precision V-I Converter
<!-- pages: 15-16 -->

The AD620, along with another op amp and two resistors, makes a precision current source (Figure 40). The op amp buffers the reference terminal to maintain good CMR. The output voltage, V_{X}, of the AD620 appears across R1, which converts it to a current. This current, less only the input bias current of the op amp, then flows out to the load.

![Figure 40. Precision Voltage-to-Current Converter (Operates on 1.8 mA, ±3 V)](ad620/figures/ad620-f043.png)

*Figure 40. Precision Voltage-to-Current Converter (Operates on 1.8 mA, ±3 V)*

### GAIN SELECTION
<!-- page: 15 -->

The AD620 gain is resistor-programmed by R_{G}, or more precisely, by whatever impedance appears between Pins 1 and 8. The AD620 is designed to offer accurate gains using 0.1% to 1% resistors. Table 5 shows required values of R_{G} for various gains. Note that for G = 1, the R_{G} pins are unconnected (R_{G} = ∞). For any arbitrary gain, R_{G} can be calculated by using the formula:

$$R_{G} = \frac{49.4 k \Omega}{G - 1}$$

To minimize gain error, avoid high parasitic resistance in series with R_{G}; to minimize gain drift, R_{G} should have a low TC-less than 10 ppm/°C-for the best performance.

**Table 5. Required Values of Gain Resistors** ([table-04-p15-data.csv](ad620/tables/table-04-p15-data.csv), p. 15)

| 1% Std Table Value of R_{G}(Ω) | Calculated Gain | 0.1% Std Table Value of R_{G}(Ω ) | Calculated Gain |
|---|---|---|---|
| 49.9 k | 1.990 | 49.3 k | 2.002 |
| 12.4 k | 4.984 | 12.4 k | 4.984 |
| 5.49 k | 9.998 | 5.49 k | 9.998 |
| 2.61 k | 19.93 | 2.61 k | 19.93 |
| 1.00 k | 50.40 | 1.01 k | 49.91 |
| 499 | 100.0 | 499 | 100.0 |
| 249 | 199.4 | 249 | 199.4 |
| 100 | 495.0 | 98.8 | 501.0 |
| 49.9 | 991.0 | 49.3 | 1,003.0 |

### INPUT AND OUTPUT OFFSET VOLTAGE
<!-- page: 15 -->

The low errors of the AD620 are attributed to two sources, input and output errors. The output error is divided by G when referred to the input. In practice, the input errors dominate at high gains, and the output errors dominate at low gains. The total V_{OS} for a given gain is calculated as

Total Error RTI = input error + (output error/G)

Total Error RTO = (input error × G) + output error

### REFERENCE TERMINAL
<!-- page: 15 -->

The reference terminal potential defines the zero output voltage and is especially useful when the load does not share a precise ground with the rest of the system. It provides a direct means of injecting a precise offset to the output, with an allowable range of 2 V within the supply voltages. Parasitic resistance should be kept to a minimum for optimum CMR.

### INPUT PROTECTION
<!-- page: 15 -->

The AD620 safely withstands an input current of ±60 mA for several hours at room temperature. This is true for all gains and power on and off, which is useful if the signal source and amplifier are powered separately. For longer time periods, the input current should not exceed 6 mA.

For input voltages beyond the supplies, a protection resistor should be placed in series with each input to limit the current to 6 mA. These can be the same resistors as those used in the RFI filter. High values of resistance can impact the noise and AC CMRR performance of the system. Low leakage diodes (such as the BAV199) can be placed at the inputs to reduce the required protection resistance.

![Figure 41. Diode Protection for Voltages Beyond Supply](ad620/figures/ad620-f044.png)

*Figure 41. Diode Protection for Voltages Beyond Supply*

### RF INTERFERENCE
<!-- page: 15 -->

All instrumentation amplifiers rectify small out of band signals. The disturbance may appear as a small dc voltage offset. High frequency signals can be filtered with a low pass R-C network placed at the input of the instrumentation amplifier. Figure 42 demonstrates such a configuration. The filter limits the input signal according to the following relationship:

$$\ FilterFreq_{DIFF} = \frac{1}{2 \pi R ( 2 C_{D} + C_{C} )}$$

$$FilterFreq_{CM} = \frac{1}{2 \pi RC_{C}}$$


where C_{D} ≥10CC.

C_{D} affects the difference signal. C_{C} affects the common-mode signal. Any mismatch in R × C_{C} degrades the AD620 CMRR. To avoid inadvertently reducing CMRR-bandwidth performance, make sure that C_{C} is at least one magnitude smaller than C_{D}. The effect of mismatched CCs is reduced with a larger C_{D}:C_{C} ratio.

![Figure 42. Circuit to Attenuate RF Interference](ad620/figures/ad620-f045.png)

*Figure 42. Circuit to Attenuate RF Interference*

### COMMON-MODE REJECTION
<!-- pages: 16-17 -->

Instrumentation amplifiers, such as the AD620, offer high CMR, which is a measure of the change in output voltage when both inputs are changed by equal amounts. These specifications are usually given for a full-range input voltage change and a specified source imbalance.

For optimal CMR, the reference terminal should be tied to a low impedance point, and differences in capacitance and resistance should be kept to a minimum between the two inputs. In many applications, shielded cables are used to minimize noise; for best CMR over frequency, the shield should be properly driven. Figure 43 and Figure 44 show active data guards that are configured to improve ac common-mode rejections by 'bootstrapping' the capacitances of input cable shields, thus minimizing the capacitance mismatch between the inputs.

![Figure 43. Differential Shield Driver](ad620/figures/ad620-f046.png)

*Figure 43. Differential Shield Driver*

![Figure 44. Common-Mode Shield Driver](ad620/figures/ad620-f047.png)

*Figure 44. Common-Mode Shield Driver*

### GROUNDING
<!-- page: 16 -->

Since the AD620 output voltage is developed with respect to the potential on the reference terminal, it can solve many grounding problems by simply tying the REF pin to the appropriate 'local ground. '

To isolate low level analog signals from a noisy digital environment, many data-acquisition components have separate analog and digital ground pins (Figure 45). It would be convenient to use a single ground line; however, current through ground wires and PC runs of the circuit card can cause hundreds of millivolts of error. Therefore, separate ground returns should be provided to minimize the current flow from the sensitive points to the system ground. These ground returns must be tied together at some point, usually best at the ADC package shown in Figure 45.

![Figure 45. Basic Grounding Practice](ad620/figures/ad620-f048.png)

*Figure 45. Basic Grounding Practice*

### GROUND RETURNS FOR INPUT BIAS CURRENTS
<!-- pages: 17-19 -->

Input bias currents are those currents necessary to bias the input transistors of an amplifier. There must be a direct return path for these currents. Therefore, when amplifying 'floating' input sources, such as transformers or ac-coupled sources, there must be a dc path from each input to ground, as shown in Figure 46, Figure 47, and Figure 48. Refer to A Designer's Guide to Instrumentation Amplifiers (free from Analog Devices) for more information regarding in-amp applications.

![Figure 46. Ground Returns for Bias Currents with Transformer-Coupled Inputs](ad620/figures/ad620-f049.png)

*Figure 46. Ground Returns for Bias Currents with Transformer-Coupled Inputs*

![Figure 47. Ground Returns for Bias Currents with Thermocouple Inputs](ad620/figures/ad620-f050.png)

*Figure 47. Ground Returns for Bias Currents with Thermocouple Inputs*

![Figure 48. Ground Returns for Bias Currents with AC-Coupled Inputs](ad620/figures/ad620-f051.png)

*Figure 48. Ground Returns for Bias Currents with AC-Coupled Inputs*

### AD620ACHIPS INFORMATION
<!-- page: 18 -->

Die size: 1803 µm × 3175 µm

Die thickness: 483 µm

Bond Pad Metal: 1% Copper Doped Aluminum

To minimize gain errors introduced by the bond wires, use Kelvin connections between the chip and the gain resistor, R_{G}, by connecting Pad 1A and Pad 1B in parallel to one end of R_{G} and Pad 8A and Pad 8B in parallel to the other end of R_{G}. For unity gain applications where R_{G} is not required, Pad 1A and Pad 1B must be bonded together as well as the Pad 8A and Pad 8B.

![Figure 49. Bond Pad Diagram](ad620/figures/ad620-f052.png)

*Figure 49. Bond Pad Diagram*

**Table 6. Bond Pad Information** ([table-05-p18-pin.csv](ad620/tables/table-05-p18-pin.csv), p. 18)

PAD CORDINATES[^1]
| Pad No. | Mnemonic | X (µm) | Y (µm) |
|---|---|---|---|
| 1A | R_{G} | −623 | +1424 |
| 1B | R_{G} | −789 | +628 |
| 2 | −IN | −790 | +453 |
| 3 | +IN | −790 | −294 |
| 4 | −V_{S} | −788 | −1419 |
| 5 | REF | +570 | −1429 |
| 6 | OUTPUT | +693 | −1254 |
| 7 | +V_{S} | +693 | +139 |
| 8A | R_{G} | +505 | +1423 |
| 8B | R_{G} | +693 | +372 |

- **Note 1:** The pad coordinates indicate the center of each pad, referenced to the center of the die. The die orientation is indicated by the logo, as shown in Figure 49.


### OUTLINE DIMENSIONS
<!-- pages: 19-20 -->

![Figure 50. 8-Lead Plastic Dual In-Line Package (PDIP)](ad620/figures/ad620-f053.png)

COMPLIANT TO JEDEC STANDARDS MS-001

CONTROLLING DIMENSIONSARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.

*Figure 50. 8-Lead Plastic Dual In-Line Package [PDIP]* 
Narrow Body (N-8).

Dimensions shown in inches and (millimeters)

![Figure 51. 8-Lead Ceramic Dual In-Line Package (CERDIP) (Q-8)](ad620/figures/ad620-f054.png)

CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.

*Figure 51. 8-Lead Ceramic Dual In-Line Package [CERDIP] (Q-8)* 
Dimensions shown in inches and (millimeters)

![Figure 52. 8-Lead Standard Small Outline Package (SOIC_N) Narrow Body (R-8)](ad620/figures/ad620-f055.png)

COMPLIANT TO JEDEC STANDARDS MS-012-AA

CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLYAND ARE NOT APPROPRIATE FOR USE IN DESIGN.

*Figure 52. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8)*
Dimensions shown in millimeters and (inches)


### ORDERING GUIDE
<!-- page: 20 -->

**Ordering Guide** ([table-06-p20-data.csv](ad620/tables/table-06-p20-data.csv), p. 20)

| Model[^1] | Temperature Range | Package Description | Package Option |
|---|---|---|---|
| AD620AN | −40°C to +85°C | 8-Lead PDIP | N-8 |
| AD620ANZ | −40°C to +85°C | 8-Lead PDIP | N-8 |
| AD620BN | −40°C to +85°C | 8-Lead PDIP | N-8 |
| AD620BNZ | −40°C to +85°C | 8-Lead PDIP | N-8 |
| AD620AR | −40°C to +85°C | 8-Lead SOIC_N | R-8 |
| AD620ARZ | −40°C to +85°C | 8-Lead SOIC_N | R-8 |
| AD620AR-REEL | −40°C to +85°C | 8-Lead SOIC_N, 13" Tape and Reel | R-8 |
| AD620ARZ-REEL | −40°C to +85°C | 8-Lead SOIC_N, 13" Tape and Reel | R-8 |
| AD620AR-REEL7 | −40°C to +85°C | 8-Lead SOIC_N, 7" Tape and Reel | R-8 |
| AD620ARZ-REEL7 | −40°C to +85°C | 8-Lead SOIC_N, 7" Tape and Reel | R-8 |
| AD620BR | −40°C to +85°C | 8-Lead SOIC_N | R-8 |
| AD620BRZ | −40°C to +85°C | 8-Lead SOIC_N | R-8 |
| AD620BR-REEL | −40°C to +85°C | 8-Lead SOIC_N, 13" Tape and Reel | R-8 |
| AD620BRZ-RL | −40°C to +85°C | 8-Lead SOIC_N, 13" Tape and Reel | R-8 |
| AD620BR-REEL7 | −40°C to +85°C | 8-Lead SOIC_N, 7" Tape and Reel | R-8 |
| AD620BRZ-R7 | −40°C to +85°C | 8-Lead SOIC_N, 7" Tape and Reel | R-8 |
| AD620ACHIPS | −40°C to +85°C | Die Form |  |
| AD620SQ/883B | −55°C to +125°C | 8-Lead CERDIP | Q-8 |

- **Note 1:** Z = RoHS Compliant Part.

