---
type: Analog Component
title: "AD4858 — Buffered, 8-Channel Simultaneous Sampling, 20-Bit 1 MSPS DAS"
description: "Buffered, 8-Channel Simultaneous Sampling, 20-Bit 1 MSPS DAS"
resource: "https://www.analog.com/en/products/ad4858.html"
tags: ["datasheet", "adi"]
status: draft
sources:
  - id: "datasheet"
    resource: "https://www.analog.com/media/en/technical-documentation/data-sheets/ad4858.pdf"
    title: "AD4858 data sheet"
    author: "team:analog-devices"
    last_modified: "October 18, 2023"
tables:
  - file: "ad4858/tables/table-00-p4-spec.csv"
    title: "Table 1. Specifications"
    page: 4
  - file: "ad4858/tables/table-01-p13-spec.csv"
    title: "Table 2. Universal Timing"
    page: 13
  - file: "ad4858/tables/table-02-p14-spec.csv"
    title: "Table 3. SPI Register Configuration Bus Read/Write Timing"
    page: 14
  - file: "ad4858/tables/table-03-p16-spec.csv"
    title: "Table 4. CMOS Conversion Data Output Timing"
    page: 16
  - file: "ad4858/tables/table-04-p17-spec.csv"
    title: "Table 5. LVDS Conversion Data Output Timing"
    page: 17
  - file: "ad4858/tables/table-05-p18-abs_max.csv"
    title: "Table 6. Absolute Maximum Ratings"
    page: 18
  - file: "ad4858/tables/table-06-p18-data.csv"
    title: "Table 7. Thermal Resistance"
    page: 18
  - file: "ad4858/tables/table-07-p18-data.csv"
    title: "Table 8. AD4858, 64-Ball BGA (ESD Ratings)"
    page: 18
  - file: "ad4858/tables/pin-matrix-1.csv"
    title: "Figure 8. Pin Configuration (Pin Matrix)"
    page: 19
  - file: "ad4858/tables/table-08-p19-pin.csv"
    title: "Table 9. Universal Pin Function Descriptions"
    page: 19
  - file: "ad4858/tables/table-09-p21-pin.csv"
    title: "Table 10. CMOS Conversion Data Bus Pin Function Descriptions"
    page: 21
  - file: "ad4858/tables/table-10-p21-pin.csv"
    title: "Table 11. LVDS Conversion Data Bus Pin Function Descriptions"
    page: 21
  - file: "ad4858/tables/table-11-p31-data.csv"
    title: "Table 12. SoftSpan Range Properties"
    page: 31
  - file: "ad4858/tables/table-12-p31-register.csv"
    title: "Table 13. Per Channel SoftSpan Registers"
    page: 31
  - file: "ad4858/tables/table-14-p33-register.csv"
    title: "Table 15. Per Channel Gain Correction Registers"
    page: 33
  - file: "ad4858/tables/table-15-p34-register.csv"
    title: "Table 16. Per Channel Phase Correction Registers"
    page: 34
  - file: "ad4858/tables/table-18-p46-register.csv"
    title: "Table 19. Per Channel Test Pattern Registers"
    page: 46
  - file: "ad4858/tables/table-19-p50-register.csv"
    title: "Table 20. Register Summary"
    page: 50
  - file: "ad4858/tables/table-20-p54-register.csv"
    title: "Table 21. Bit Descriptions for SPI_CONFIG_A"
    page: 54
  - file: "ad4858/tables/table-21-p55-register.csv"
    title: "Table 22. Bit Descriptions for SPI_CONFIG_B"
    page: 55
  - file: "ad4858/tables/table-22-p55-register.csv"
    title: "Table 23. Bit Descriptions for DEVICE_CONFIG"
    page: 55
  - file: "ad4858/tables/table-23-p55-register.csv"
    title: "Table 24. Bit Descriptions for DEVICE_TYPE"
    page: 55
  - file: "ad4858/tables/table-24-p56-register.csv"
    title: "Table 25. Bit Descriptions for PRODUCT_ID_L"
    page: 56
  - file: "ad4858/tables/table-25-p56-register.csv"
    title: "Table 26. Bit Descriptions for PRODUCT_ID_H"
    page: 56
  - file: "ad4858/tables/table-26-p56-register.csv"
    title: "Table 27. Bit Descriptions for DEVICE_GRADE"
    page: 56
  - file: "ad4858/tables/table-27-p57-register.csv"
    title: "Table 28. Bit Descriptions for SCRATCH_PAD"
    page: 57
  - file: "ad4858/tables/table-28-p57-register.csv"
    title: "Table 29. Bit Descriptions for SPI_REVISION"
    page: 57
  - file: "ad4858/tables/table-29-p57-register.csv"
    title: "Table 30. Bit Descriptions for VENDOR_ID_L"
    page: 57
  - file: "ad4858/tables/table-30-p57-register.csv"
    title: "Table 31. Bit Descriptions for VENDOR_ID_H"
    page: 57
  - file: "ad4858/tables/table-31-p58-register.csv"
    title: "Table 32. Bit Descriptions for LOOP_CONFIG_A"
    page: 58
  - file: "ad4858/tables/table-32-p58-register.csv"
    title: "Table 33. Bit Descriptions for LOOP_CONFIG_B"
    page: 58
  - file: "ad4858/tables/table-33-p59-register.csv"
    title: "Table 34. Bit Descriptions for SPI_CONFIG_C"
    page: 59
  - file: "ad4858/tables/table-34-p59-register.csv"
    title: "Table 35. Bit Descriptions for SPI_STATUS"
    page: 59
  - file: "ad4858/tables/table-35-p60-register.csv"
    title: "Table 36. Bit Descriptions for SPI_CONFIG_D"
    page: 60
  - file: "ad4858/tables/table-36-p60-register.csv"
    title: "Table 37. Bit Descriptions for DEVICE_STATUS"
    page: 60
  - file: "ad4858/tables/table-37-p61-register.csv"
    title: "Table 38. Bit Descriptions for CH_OR_STATUS"
    page: 61
  - file: "ad4858/tables/table-38-p62-register.csv"
    title: "Table 39. Bit Descriptions for CH_UR_STATUS"
    page: 62
  - file: "ad4858/tables/table-39-p63-register.csv"
    title: "Table 40. Bit Descriptions for REGMAP_CRC"
    page: 63
  - file: "ad4858/tables/table-40-p63-register.csv"
    title: "Table 41. Bit Descriptions for DEVICE_CTRL"
    page: 63
  - file: "ad4858/tables/table-41-p64-register.csv"
    title: "Table 42. Bit Descriptions for PACKET"
    page: 64
  - file: "ad4858/tables/table-42-p64-register.csv"
    title: "Table 43. Bit Descriptions for OVERSAMPLE"
    page: 64
  - file: "ad4858/tables/table-43-p65-register.csv"
    title: "Table 44. Bit Descriptions for SEAMLESS_HDR"
    page: 65
  - file: "ad4858/tables/table-44-p66-register.csv"
    title: "Table 45. Bit Descriptions for CH_SLEEP"
    page: 66
  - file: "ad4858/tables/table-45-p66-register.csv"
    title: "Table 46. Bit Descriptions for CH0_SOFTSPAN"
    page: 66
  - file: "ad4858/tables/table-46-p67-register.csv"
    title: "Table 47. Bit Descriptions for CH0_OFFSET"
    page: 67
  - file: "ad4858/tables/table-47-p67-register.csv"
    title: "Table 48. Bit Descriptions for CH0_GAIN"
    page: 67
  - file: "ad4858/tables/table-48-p68-register.csv"
    title: "Table 49. Bit Descriptions for CH0_PHASE"
    page: 68
  - file: "ad4858/tables/table-49-p68-register.csv"
    title: "Table 50. Bit Descriptions for CH0_OR"
    page: 68
  - file: "ad4858/tables/table-50-p68-register.csv"
    title: "Table 51. Bit Descriptions for CH0_UR"
    page: 68
  - file: "ad4858/tables/table-51-p69-register.csv"
    title: "Table 52. Bit Descriptions for CH0_TESTPAT"
    page: 69
  - file: "ad4858/tables/table-53-p70-data.csv"
    title: "Evaluation Board"
    page: 70
  - file: "ad4858/tables/table-17-p35-register.csv"
    title: "Table 18. Per Channel Underrange Limit Registers"
    page: 35
  - file: "ad4858/tables/table-52-p70-data.csv"
    title: "Ordering Guide"
    page: 70
figures:
  - file: "ad4858/figures/ad4858-f001.png"
    caption: ""
    type: "other"
    page: 1
  - file: "ad4858/figures/ad4858-f002.png"
    caption: "Figure 1. Functional Block Diagram (Example Analog-Input Signal Use Cases Shown)"
    type: "block_diagram"
    page: 1
  - file: "ad4858/figures/ad4858-f003.png"
    caption: "Figure 2. Universal Timing"
    type: "timing_diagram"
    page: 13
  - file: "ad4858/figures/ad4858-f004.png"
    caption: "Figure 3. SPI Register Configuration Bus Write Timing"
    type: "timing_diagram"
    page: 14
  - file: "ad4858/figures/ad4858-f005.png"
    caption: "Figure 4. SPI Register Configuration Bus 3-Wire Read Timing"
    type: "timing_diagram"
    page: 15
  - file: "ad4858/figures/ad4858-f006.png"
    caption: "Figure 5. SPI Register Configuration Bus 4-Wire Read Timing"
    type: "timing_diagram"
    page: 15
  - file: "ad4858/figures/ad4858-f007.png"
    caption: "Figure 6. CMOS Conversion Data Bus Timing"
    type: "timing_diagram"
    page: 16
  - file: "ad4858/figures/ad4858-f010.png"
    caption: "Figure 9. INL Error vs. Differential Input Voltage, SoftSpan 15 to SoftSpan 14"
    type: "characteristic_curve"
    page: 22
  - file: "ad4858/figures/ad4858-f011.png"
    caption: "Figure 10. INL Error vs. Differential Input Voltage, SoftSpan 9 to SoftSpan 6"
    type: "characteristic_curve"
    page: 22
  - file: "ad4858/figures/ad4858-f012.png"
    caption: "Figure 11. INL Error vs. Differential Input Voltage, SoftSpan 1 to SoftSpan 0"
    type: "characteristic_curve"
    page: 22
  - file: "ad4858/figures/ad4858-f013.png"
    caption: "Figure 12. INL Error vs. Differential Input Voltage, SoftSpan 13 to SoftSpan 10"
    type: "characteristic_curve"
    page: 22
  - file: "ad4858/figures/ad4858-f014.png"
    caption: "Figure 13. INL Error vs. Differential Input Voltage, SoftSpan 5 to SoftSpan 2"
    type: "characteristic_curve"
    page: 22
  - file: "ad4858/figures/ad4858-f015.png"
    caption: "Figure 14. DNL Error vs. Differential Input Voltage"
    type: "characteristic_curve"
    page: 22
  - file: "ad4858/figures/ad4858-f016.png"
    caption: "Figure 15. INL Error vs. Input Common Mode and Input Differential Voltage"
    type: "characteristic_curve"
    page: 23
  - file: "ad4858/figures/ad4858-f017.png"
    caption: "Figure 16. DC Code Histogram, Near Zero Scale"
    type: "characteristic_curve"
    page: 23
  - file: "ad4858/figures/ad4858-f018.png"
    caption: "Figure 17. Input Step Response, Large Signal Settling"
    type: "characteristic_curve"
    page: 23
  - file: "ad4858/figures/ad4858-f019.png"
    caption: "Figure 18. Input-Referred Noise vs. Differential Input Voltage"
    type: "characteristic_curve"
    page: 23
  - file: "ad4858/figures/ad4858-f020.png"
    caption: "Figure 19. DC Code Histogram, Near Full Scale"
    type: "characteristic_curve"
    page: 23
  - file: "ad4858/figures/ad4858-f021.png"
    caption: "Figure 20. Input Step Response, Fine Settling"
    type: "characteristic_curve"
    page: 23
  - file: "ad4858/figures/ad4858-f022.png"
    caption: "Figure 21. FFT, 1 MSPS, f_{IN} = 1 kHz, ±40 V Range"
    type: "characteristic_curve"
    page: 24
  - file: "ad4858/figures/ad4858-f023.png"
    caption: "Figure 22. FFT, 1 MSPS, f_{IN} = 1 kHz, ±5 V Range"
    type: "characteristic_curve"
    page: 24
  - file: "ad4858/figures/ad4858-f024.png"
    caption: "Figure 23. SNR, SINAD, and THD vs. Input Level"
    type: "characteristic_curve"
    page: 24
  - file: "ad4858/figures/ad4858-f025.png"
    caption: "Figure 24. FFT, 1 MSPS, f_{IN} = 1 kHz, ±10 V Range"
    type: "characteristic_curve"
    page: 24
  - file: "ad4858/figures/ad4858-f026.png"
    caption: "Figure 25. FFT, 1 MSPS, f_{INx+} = 991 Hz, f INx= 1.6 kHz, ±40 V Range"
    type: "characteristic_curve"
    page: 24
  - file: "ad4858/figures/ad4858-f027.png"
    caption: "Figure 26. SNR and SINAD vs. Input Frequency"
    type: "characteristic_curve"
    page: 24
  - file: "ad4858/figures/ad4858-f028.png"
    caption: "Figure 27. THD, Harmonics vs. Input Frequency"
    type: "characteristic_curve"
    page: 25
  - file: "ad4858/figures/ad4858-f029.png"
    caption: "Figure 28. Crosstalk vs. Interferer Frequency"
    type: "characteristic_curve"
    page: 25
  - file: "ad4858/figures/ad4858-f030.png"
    caption: "Figure 29. Power Supply Rejection Ratio (PSRR) vs. Frequency"
    type: "characteristic_curve"
    page: 25
  - file: "ad4858/figures/ad4858-f031.png"
    caption: "Figure 30. CMRR vs. Input Frequency"
    type: "characteristic_curve"
    page: 25
  - file: "ad4858/figures/ad4858-f032.png"
    caption: "Figure 31. Zero-Scale Error vs. Common-Mode Input Voltage"
    type: "characteristic_curve"
    page: 25
  - file: "ad4858/figures/ad4858-f033.png"
    caption: "Figure 32. PSRR vs. Frequency, Internal and External Reference"
    type: "characteristic_curve"
    page: 25
  - file: "ad4858/figures/ad4858-f034.png"
    caption: "Figure 33. Supply Current vs. Sample Rate"
    type: "characteristic_curve"
    page: 26
  - file: "ad4858/figures/ad4858-f035.png"
    caption: "Figure 34. Dynamic Range vs. Oversampling Ratio"
    type: "characteristic_curve"
    page: 26
  - file: "ad4858/figures/ad4858-f036.png"
    caption: "Figure 35. Change in Internal Reference Voltage vs. Burn-In Time"
    type: "characteristic_curve"
    page: 26
  - file: "ad4858/figures/ad4858-f037.png"
    caption: "Figure 36. Burst Conversion Response, f_{S} = 1 MSPS"
    type: "characteristic_curve"
    page: 26
  - file: "ad4858/figures/ad4858-f038.png"
    caption: "Figure 37. Low Frequency Noise over 10 seconds"
    type: "characteristic_curve"
    page: 26
  - file: "ad4858/figures/ad4858-f039.png"
    caption: "Figure 38. Change in Zero-Scale Error vs. Burn-In Time"
    type: "characteristic_curve"
    page: 26
  - file: "ad4858/figures/ad4858-f040.png"
    caption: "Figure 39. Zero-Scale Error vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "ad4858/figures/ad4858-f041.png"
    caption: "Figure 40. Internal Reference Output vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "ad4858/figures/ad4858-f042.png"
    caption: "Figure 41. Analog Input Leakage Current vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "ad4858/figures/ad4858-f043.png"
    caption: "Figure 42. Positive Full-Scale Error vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "ad4858/figures/ad4858-f044.png"
    caption: "Figure 43. Reference Buffer Offset Voltage vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "ad4858/figures/ad4858-f045.png"
    caption: "Figure 44. INL/DNL Error vs. Temperature"
    type: "characteristic_curve"
    page: 27
  - file: "ad4858/figures/ad4858-f046.png"
    caption: "Figure 45. SNR and SINAD vs. Temperature"
    type: "characteristic_curve"
    page: 28
  - file: "ad4858/figures/ad4858-f047.png"
    caption: "Figure 46. Supply Current vs. Temperature"
    type: "characteristic_curve"
    page: 28
  - file: "ad4858/figures/ad4858-f048.png"
    caption: "Figure 47. THD, Harmonics vs. Temperature"
    type: "characteristic_curve"
    page: 28
  - file: "ad4858/figures/ad4858-f049.png"
    caption: "Figure 48. Power-Down Current vs. Temperature"
    type: "characteristic_curve"
    page: 28
  - file: "ad4858/figures/ad4858-f050.png"
    caption: "Figure 49. AD4858 Ideal Bipolar Input Transfer Function. N = 20 bits"
    type: "characteristic_curve"
    page: 30
  - file: "ad4858/figures/ad4858-f051.png"
    caption: "Figure 50. AD4858 Ideal Unipolar Input Transfer Function. N = 20 bits"
    type: "characteristic_curve"
    page: 30
  - file: "ad4858/figures/ad4858-f052.png"
    caption: "Figure 51. Oversampling Mode with 4× Oversampling Ratio (OS_RATIO = 0x1)"
    type: "timing_diagram"
    page: 32
  - file: "ad4858/figures/ad4858-f053.png"
    caption: "Figure 52. Oversampling Mode with 4× Oversampling Ratio (OS_RATIO = 0x1), Channel 7 Averages Phase-Shifted by One Sample (CH7_PHASE = 0x0001)"
    type: "timing_diagram"
    page: 34
  - file: "ad4858/figures/ad4858-f054.png"
    caption: "Figure 53. Equivalent Circuit for Differential Analog Inputs, Single Channel"
    type: "other"
    page: 36
  - file: "ad4858/figures/ad4858-f055.png"
    caption: "Figure 54. External Series Resistors Limit Latchup Current During Fault Conditions and are Transparent in Normal Operation"
    type: "application_circuit"
    page: 37
  - file: "ad4858/figures/ad4858-f056.png"
    caption: "Figure 55. Example Differential Input Filter"
    type: "application_circuit"
    page: 37
  - file: "ad4858/figures/ad4858-f057.png"
    caption: "Figure 56. Internal Reference with Internal Buffer Configuration"
    type: "application_circuit"
    page: 37
  - file: "ad4858/figures/ad4858-f058.png"
    caption: "Figure 57. External Reference with Internal Buffer Configuration"
    type: "application_circuit"
    page: 38
  - file: "ad4858/figures/ad4858-f059.png"
    caption: "Figure 58. External Reference with Disabled Internal Buffer Configuration"
    type: "application_circuit"
    page: 38
  - file: "ad4858/figures/ad4858-f060.png"
    caption: "Figure 59. CNV Waveform Showing Burst Sampling"
    type: "timing_diagram"
    page: 38
  - file: "ad4858/figures/ad4858-f061.png"
    caption: "Figure 60. Burst Conversion Response of the AD4858, f_{S} = 1 MSPS"
    type: "characteristic_curve"
    page: 38
  - file: "ad4858/figures/ad4858-f062.png"
    caption: "Figure 61. Power Supply Pins of the AD4858 when V_{DDL} is supplied externally"
    type: "application_circuit"
    page: 39
  - file: "ad4858/figures/ad4858-f063.png"
    caption: "Figure 62. Nap Mode Timing for the AD4858"
    type: "timing_diagram"
    page: 39
  - file: "ad4858/figures/ad4858-f064.png"
    caption: "Figure 63. Reset Timing for the AD4858"
    type: "timing_diagram"
    page: 40
  - file: "ad4858/figures/ad4858-f065.png"
    caption: "Figure 64. CMOS Conversion Data Bus Timing, PACKET_SIZE = 0x1, OS_EN = 0, TEST_PAT = 0"
    type: "timing_diagram"
    page: 41
  - file: "ad4858/figures/ad4858-f066.png"
    caption: "Figure 65. CMOS Conversion Data Output Mode"
    type: "application_circuit"
    page: 42
  - file: "ad4858/figures/ad4858-f067.png"
    caption: "Figure 66. All Packets May Be Read Using Fewer SDO Lanes By Increasing the Number of SCKI Pulses Applied"
    type: "timing_diagram"
    page: 42
  - file: "ad4858/figures/ad4858-f068.png"
    caption: "Figure 67. LVDS Conversion Data Output Mode"
    type: "application_circuit"
    page: 42
  - file: "ad4858/figures/ad4858-f069.png"
    caption: "Figure 68. All Packets Are Sequentially Output on SDO+ and SDO-"
    type: "timing_diagram"
    page: 43
  - file: "ad4858/figures/ad4858-f070.png"
    caption: "Figure 69. LVDS Serial Conversion Data Bus Timing, PACKET_SIZE = 0x1, OS_EN = 0, TEST_PAT = 0"
    type: "timing_diagram"
    page: 43
  - file: "ad4858/figures/ad4858-f071.png"
    caption: "Figure 70. Channel and Status Packet Data Formats in Nonversampling Mode (OS_EN = 0), Test Pattern Output is Disabled (TEST_PAT = 0)"
    type: "other"
    page: 44
  - file: "ad4858/figures/ad4858-f072.png"
    caption: "Figure 71. Channel and Status Packet Data Formats in Oversampling Mode (OS_EN = 1), Test Pattern Output is Disabled (TEST_PAT = 0)"
    type: "other"
    page: 45
  - file: "ad4858/figures/ad4858-f073.png"
    caption: "Figure 72. Channel and Status Packet Data Formats with Test Pattern Output Enabled (TEST_PAT = 1)"
    type: "other"
    page: 46
  - file: "ad4858/figures/ad4858-f074.png"
    caption: "Figure 73. 3-Wire SPI Register Configuration Bus Frame"
    type: "timing_diagram"
    page: 47
  - file: "ad4858/figures/ad4858-f075.png"
    caption: "Figure 74. 4 -Wire SPI Register Configuration Bus Frame"
    type: "timing_diagram"
    page: 48
  - file: "ad4858/figures/ad4858-f076.png"
    caption: "Figure 75. Address: 0x00, Reset: 0x00, Name: SPI_CONFIG_A"
    type: "register_bitfield"
    page: 54
  - file: "ad4858/figures/ad4858-f077.png"
    caption: "Figure 76. Address: 0x01, Reset: 0x00, Name: SPI_CONFIG_B"
    type: "register_bitfield"
    page: 55
  - file: "ad4858/figures/ad4858-f078.png"
    caption: "Figure 77. Address: 0x02, Reset: 0xF0, Name: DEVICE_CONFIG"
    type: "register_bitfield"
    page: 55
  - file: "ad4858/figures/ad4858-f079.png"
    caption: "Figure 78. Address: 0x03, Reset: 0x07, Name: DEVICE_TYPE"
    type: "register_bitfield"
    page: 55
  - file: "ad4858/figures/ad4858-f080.png"
    caption: "Figure 79. Address: 0x04, Reset: 0x00, Name: PRODUCT_ID_L"
    type: "register_bitfield"
    page: 56
  - file: "ad4858/figures/ad4858-f081.png"
    caption: "Figure 80. Address: 0x05, Reset: 0x00, Name: PRODUCT_ID_H"
    type: "register_bitfield"
    page: 56
  - file: "ad4858/figures/ad4858-f082.png"
    caption: "Figure 81. Address: 0x06, Reset: 0x00, Name: DEVICE_GRADE"
    type: "register_bitfield"
    page: 56
  - file: "ad4858/figures/ad4858-f083.png"
    caption: "Figure 82. Address: 0x0A, Reset: 0x00, Name: SCRATCH_PAD"
    type: "register_bitfield"
    page: 56
  - file: "ad4858/figures/ad4858-f084.png"
    caption: "Figure 83. Address: 0x0B, Reset: 0x83, Name: SPI_REVISION"
    type: "register_bitfield"
    page: 57
  - file: "ad4858/figures/ad4858-f085.png"
    caption: "Figure 84. Address: 0x0C, Reset: 0x56, Name: VENDOR_ID_L"
    type: "register_bitfield"
    page: 57
  - file: "ad4858/figures/ad4858-f086.png"
    caption: "Figure 85. Address: 0x0D, Reset: 0x04, Name: VENDOR_ID_H"
    type: "register_bitfield"
    page: 57
  - file: "ad4858/figures/ad4858-f087.png"
    caption: "Figure 86. Address: 0x0E, Reset: 0x00, Name: LOOP_CONFIG_A"
    type: "register_bitfield"
    page: 58
  - file: "ad4858/figures/ad4858-f088.png"
    caption: "Figure 87. Address: 0x0F, Reset: 0x00, Name: LOOP_CONFIG_B"
    type: "register_bitfield"
    page: 58
  - file: "ad4858/figures/ad4858-f089.png"
    caption: "Figure 88. Address: 0x10, Reset: 0x03, Name: SPI_CONFIG_C"
    type: "register_bitfield"
    page: 58
  - file: "ad4858/figures/ad4858-f090.png"
    caption: "Figure 89. Address: 0x11, Reset: 0x00, Name: SPI_STATUS"
    type: "register_bitfield"
    page: 59
  - file: "ad4858/figures/ad4858-f091.png"
    caption: "Figure 90. Address: 0x14, Reset: 0x00, Name: SPI_CONFIG_D"
    type: "register_bitfield"
    page: 60
  - file: "ad4858/figures/ad4858-f092.png"
    caption: "Figure 91. Address: 0x20, Reset: 0x40, Name: DEVICE_STATUS"
    type: "register_bitfield"
    page: 60
  - file: "ad4858/figures/ad4858-f093.png"
    caption: "Figure 92. Address: 0x21, Reset: 0x00, Name: CH_OR_STATUS"
    type: "register_bitfield"
    page: 61
  - file: "ad4858/figures/ad4858-f094.png"
    caption: "Figure 93. Address: 0x22, Reset: 0x00, Name: CH_UR_STATUS"
    type: "register_bitfield"
    page: 62
  - file: "ad4858/figures/ad4858-f095.png"
    caption: "Figure 94. Address: 0x23 to Address: 0x24, Reset: 0x0000, Name: REGMAP_CRC"
    type: "register_bitfield"
    page: 62
  - file: "ad4858/figures/ad4858-f096.png"
    caption: "Figure 95. Address: 0x25, Reset: 0x11, Name: DEVICE_CTRL"
    type: "register_bitfield"
    page: 63
  - file: "ad4858/figures/ad4858-f097.png"
    caption: "Figure 96. Address: 0x26, Reset: 0x01, Name: PACKET"
    type: "register_bitfield"
    page: 64
  - file: "ad4858/figures/ad4858-f098.png"
    caption: "Figure 97. Address: 0x27, Reset: 0x00, Name: OVERSAMPLE"
    type: "register_bitfield"
    page: 64
  - file: "ad4858/figures/ad4858-f099.png"
    caption: "Figure 98. Address: 0x28, Reset: 0xFF, Name: SEAMLESS_HDR"
    type: "register_bitfield"
    page: 65
  - file: "ad4858/figures/ad4858-f100.png"
    caption: "Figure 99. Address: 0x29, Reset: 0x00, Name: CH_SLEEP"
    type: "register_bitfield"
    page: 66
  - file: "ad4858/figures/ad4858-f101.png"
    caption: "Figure 100. Address: 0x2A, Reset: 0x0F, Name: CH0_SOFTSPAN"
    type: "register_bitfield"
    page: 66
  - file: "ad4858/figures/ad4858-f102.png"
    caption: "Figure 101. Address: 0x2B to Address: 0x2D, Reset: 0x000000, Name: CH0_OFFSET"
    type: "register_bitfield"
    page: 67
  - file: "ad4858/figures/ad4858-f103.png"
    caption: "Figure 102. Address: 0x2E to Address: 0x2F, Reset: 0x8000, Name: CH0_GAIN"
    type: "register_bitfield"
    page: 67
  - file: "ad4858/figures/ad4858-f104.png"
    caption: "Figure 103. Address: 0x30 to Address: 0x31, Reset: 0x0000, Name: CH0_PHASE"
    type: "register_bitfield"
    page: 68
  - file: "ad4858/figures/ad4858-f105.png"
    caption: "Figure 104. Address: 0x32 to Address 0x34, Reset: 0x7FFFF0, Name: CH0_OR"
    type: "register_bitfield"
    page: 68
  - file: "ad4858/figures/ad4858-f106.png"
    caption: "Figure 105. Address: 0x35 to Address 0x37, Reset: 0x800000, Name: CH0_UR"
    type: "register_bitfield"
    page: 68
  - file: "ad4858/figures/ad4858-f108.png"
    caption: "Figure 107. 64-Ball BGA Package 7 mm × 7 mm × 1.42 mm (05-08-7086) Dimensions shown in millimeters"
    type: "other"
    page: 70
  - file: "ad4858/figures/ad4858-f110.png"
    caption: "SPECIFICATIONS Table 5. LVDS Conversion Data Output Timing Parameter Symbol Unit"
    type: "other"
    page: 17
  - file: "ad4858/figures/ad4858-f111.png"
    caption: "Figure 7. LVDS Conversion Data Bus Timing"
    type: "timing_diagram"
    page: 17
  - file: "ad4858/figures/ad4858-f112.png"
    caption: "Figure 8. Pin Configuration"
    type: "pinout"
    page: 19
  - file: "ad4858/figures/ad4858-eq01.png"
    caption: "Equation as printed (p. 33)"
    type: equation
    page: 33
  - file: "ad4858/figures/ad4858-eq02.png"
    caption: "Equation as printed (p. 44)"
    type: equation
    page: 44
  - file: "ad4858/figures/ad4858-eq03.png"
    caption: "Equation as printed (p. 45)"
    type: equation
    page: 45
curves:
  - file: "ad4858/curves/analog-input-leakage-current-vs-temperature.csv"
    caption: "Figure 41. Analog Input Leakage Current vs. Temperature"
    figure: "ad4858/figures/ad4858-f042.png"
    page: 27
    x_unit: "°C"
    y_unit: "A"
    conditions: "16 ANALOG INPUT PIN TRACES FOR EACH INPUT VOLTAGE"
  - file: "ad4858/curves/burst-conversion-response-f-s-1-msps.csv"
    caption: "Figure 36. Burst Conversion Response, f_{S} = 1 MSPS"
    figure: "ad4858/figures/ad4858-f037.png"
    page: 26
    x_unit: "µs"
    y_unit: "µV"
    conditions: "INx+ = 4.096V, INx- = 0V"
  - file: "ad4858/curves/burst-conversion-response-of-the-ad4858-f-s-1-msps.csv"
    caption: "Figure 60. Burst Conversion Response of the AD4858, f_{S} = 1 MSPS"
    figure: "ad4858/figures/ad4858-f061.png"
    page: 38
    x_unit: "µs"
    y_unit: "µV"
    conditions: "INx+ = 4.096V, INx- = 0V"
  - file: "ad4858/curves/change-in-internal-reference-voltage-vs-burn-in-time.csv"
    caption: "Figure 35. Change in Internal Reference Voltage vs. Burn-In Time"
    figure: "ad4858/figures/ad4858-f036.png"
    page: 26
    x_unit: "h"
    y_unit: "mV"
    conditions: "T_{J} = 150°C"
  - file: "ad4858/curves/change-in-zero-scale-error-vs-burn-in-time.csv"
    caption: "Figure 38. Change in Zero-Scale Error vs. Burn-In Time"
    figure: "ad4858/figures/ad4858-f039.png"
    page: 26
    x_unit: "h"
    y_unit: "µV"
    conditions: "T_{J} = 150°C"
  - file: "ad4858/curves/cmrr-vs-input-frequency.csv"
    caption: "Figure 30. CMRR vs. Input Frequency"
    figure: "ad4858/figures/ad4858-f031.png"
    page: 25
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "ALL CHANNELS; INx+ = INx- = 2V p-p SINE; INx+ = INx- = 40V p-p SINE"
  - file: "ad4858/curves/crosstalk-vs-interferer-frequency.csv"
    caption: "Figure 28. Crosstalk vs. Interferer Frequency"
    figure: "ad4858/figures/ad4858-f029.png"
    page: 25
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "IN3+ = 40V p-p SINE INTEREFERER, ALL OTHER CHANNELS ARE RECEIVERS, ALL CHANNELS CONVERTING"
  - file: "ad4858/curves/dnl-error-vs-differential-input-voltage.csv"
    caption: "Figure 14. DNL Error vs. Differential Input Voltage"
    figure: "ad4858/figures/ad4858-f015.png"
    page: 22
    x_unit: "V"
    y_unit: "LSB 20"
    conditions: "±40V RANGE, SHDR ON ALL CHANNELS"
  - file: "ad4858/curves/dynamic-range-vs-oversampling-ratio.csv"
    caption: "Figure 34. Dynamic Range vs. Oversampling Ratio"
    figure: "ad4858/figures/ad4858-f035.png"
    page: 26
    x_unit: "ratio"
    y_unit: "dBFS"
    conditions: "±40V RANGE, SHDR ON, 16384 OUTPUT SAMPLES, ALL CHANNELS"
  - file: "ad4858/curves/inl-dnl-error-vs-temperature.csv"
    caption: "Figure 44. INL/DNL Error vs. Temperature"
    figure: "ad4858/figures/ad4858-f045.png"
    page: 27
    x_unit: "°C"
    y_unit: "µV"
    conditions: "±40V RANGE, ALL CHANNELS"
  - file: "ad4858/curves/inl-error-vs-differential-input-voltage-softspan-1-to-softspan-0.csv"
    caption: "Figure 11. INL Error vs. Differential Input Voltage, SoftSpan 1 to SoftSpan 0"
    figure: "ad4858/figures/ad4858-f012.png"
    page: 22
    x_unit: "V"
    y_unit: "µV"
  - file: "ad4858/curves/inl-error-vs-differential-input-voltage-softspan-13-to-softspan-10.csv"
    caption: "Figure 12. INL Error vs. Differential Input Voltage, SoftSpan 13 to SoftSpan 10"
    figure: "ad4858/figures/ad4858-f013.png"
    page: 22
    x_unit: "V"
    y_unit: "µV"
  - file: "ad4858/curves/inl-error-vs-differential-input-voltage-softspan-15-to-softspan-14.csv"
    caption: "Figure 9. INL Error vs. Differential Input Voltage, SoftSpan 15 to SoftSpan 14"
    figure: "ad4858/figures/ad4858-f010.png"
    page: 22
    x_unit: "V"
    y_unit: "µV"
  - file: "ad4858/curves/inl-error-vs-differential-input-voltage-softspan-5-to-softspan-2.csv"
    caption: "Figure 13. INL Error vs. Differential Input Voltage, SoftSpan 5 to SoftSpan 2"
    figure: "ad4858/figures/ad4858-f014.png"
    page: 22
    x_unit: "V"
    y_unit: "µV"
  - file: "ad4858/curves/inl-error-vs-differential-input-voltage-softspan-9-to-softspan-6.csv"
    caption: "Figure 10. INL Error vs. Differential Input Voltage, SoftSpan 9 to SoftSpan 6"
    figure: "ad4858/figures/ad4858-f011.png"
    page: 22
    x_unit: "V"
    y_unit: "µV"
  - file: "ad4858/curves/input-referred-noise-vs-differential-input-voltage.csv"
    caption: "Figure 18. Input-Referred Noise vs. Differential Input Voltage"
    figure: "ad4858/figures/ad4858-f019.png"
    page: 23
    x_unit: "V"
    y_unit: "µV rms"
    conditions: "VALID FOR BIPOLAR AND UNIPOLAR RANGES"
  - file: "ad4858/curves/input-step-response-fine-settling.csv"
    caption: "Figure 20. Input Step Response, Fine Settling"
    figure: "ad4858/figures/ad4858-f021.png"
    page: 23
    x_unit: "ns"
    y_unit: "mV"
    conditions: "SINGLE-ENDED 40V p-p STEP, ±50ppm"
  - file: "ad4858/curves/input-step-response-large-signal-settling.csv"
    caption: "Figure 17. Input Step Response, Large Signal Settling"
    figure: "ad4858/figures/ad4858-f018.png"
    page: 23
    x_unit: "ns"
    y_unit: "V"
    conditions: "ACCURACY IN THIS REGION SEVERELY DEGRADED DUE TO HIGH dV/dt NEAR SAMPLE"
  - file: "ad4858/curves/internal-reference-output-vs-temperature.csv"
    caption: "Figure 40. Internal Reference Output vs. Temperature"
    figure: "ad4858/figures/ad4858-f041.png"
    page: 27
    x_unit: "°C"
    y_unit: "V"
    conditions: "15 UNITS"
  - file: "ad4858/curves/positive-full-scale-error-vs-temperature.csv"
    caption: "Figure 42. Positive Full-Scale Error vs. Temperature"
    figure: "ad4858/figures/ad4858-f043.png"
    page: 27
    x_unit: "°C"
    y_unit: "%"
    conditions: "REFIO OVERDRIVEN, V_{REFIO} = 4.096V, ALL CHANNELS"
  - file: "ad4858/curves/power-down-current-vs-temperature.csv"
    caption: "Figure 48. Power-Down Current vs. Temperature"
    figure: "ad4858/figures/ad4858-f049.png"
    page: 28
    x_unit: "°C"
    y_unit: "A"
  - file: "ad4858/curves/power-supply-rejection-ratio-psrr-vs-frequency.csv"
    caption: "Figure 29. Power Supply Rejection Ratio (PSRR) vs. Frequency"
    figure: "ad4858/figures/ad4858-f030.png"
    page: 25
    x_unit: "Hz"
    y_unit: "dB"
    conditions: "EXTERNAL REFIO (OVERDRIVEN), INx+ = 4.096V, INx- = 0V"
  - file: "ad4858/curves/psrr-vs-frequency-internal-and-external-reference.csv"
    caption: "Figure 32. PSRR vs. Frequency, Internal and External Reference"
    figure: "ad4858/figures/ad4858-f033.png"
    page: 25
    x_unit: "Hz"
    y_unit: "dB"
  - file: "ad4858/curves/reference-buffer-offset-voltage-vs-temperature.csv"
    caption: "Figure 43. Reference Buffer Offset Voltage vs. Temperature"
    figure: "ad4858/figures/ad4858-f044.png"
    page: 27
    x_unit: "°C"
    y_unit: "µV"
  - file: "ad4858/curves/snr-and-sinad-vs-input-frequency.csv"
    caption: "Figure 26. SNR and SINAD vs. Input Frequency"
    figure: "ad4858/figures/ad4858-f027.png"
    page: 24
    x_unit: "Hz"
    y_unit: "dBFS"
    conditions: "±40V RANGE, SHDR ON"
  - file: "ad4858/curves/snr-and-sinad-vs-temperature.csv"
    caption: "Figure 45. SNR and SINAD vs. Temperature"
    figure: "ad4858/figures/ad4858-f046.png"
    page: 28
    x_unit: "°C"
    y_unit: "dBFS"
    conditions: "±40V RANGE, FULLY DIFFERENTIAL DRIVE (INx− = −INx+)"
  - file: "ad4858/curves/snr-sinad-and-thd-vs-input-level.csv"
    caption: "Figure 23. SNR, SINAD, and THD vs. Input Level"
    figure: "ad4858/figures/ad4858-f024.png"
    page: 24
    x_unit: "dBFS"
    y_unit: "dBFS"
    conditions: "±40V RANGE, f_{IN} = 1kHz, FULLY DIFFERENTIAL DRIVE (INx− = −INx+)"
  - file: "ad4858/curves/supply-current-vs-sample-rate.csv"
    caption: "Figure 33. Supply Current vs. Sample Rate"
    figure: "ad4858/figures/ad4858-f034.png"
    page: 26
  - file: "ad4858/curves/supply-current-vs-temperature.csv"
    caption: "Figure 46. Supply Current vs. Temperature"
    figure: "ad4858/figures/ad4858-f047.png"
    page: 28
    x_unit: "°C"
    y_unit: "mA"
    conditions: "CMOS OPERATING MODE, f_{S} = 1MSPS"
  - file: "ad4858/curves/thd-harmonics-vs-input-frequency.csv"
    caption: "Figure 27. THD, Harmonics vs. Input Frequency"
    figure: "ad4858/figures/ad4858-f028.png"
    page: 25
    x_unit: "Hz"
    y_unit: "dBFS"
    conditions: "±40V RANGE, SHDR ON"
  - file: "ad4858/curves/thd-harmonics-vs-temperature.csv"
    caption: "Figure 47. THD, Harmonics vs. Temperature"
    figure: "ad4858/figures/ad4858-f048.png"
    page: 28
    x_unit: "°C"
    y_unit: "dBc"
    conditions: "±40V RANGE, FULLY DIFFERENTIAL DRIVE (INx− = −INx+)"
  - file: "ad4858/curves/zero-scale-error-vs-common-mode-input-voltage.csv"
    caption: "Figure 31. Zero-Scale Error vs. Common-Mode Input Voltage"
    figure: "ad4858/figures/ad4858-f032.png"
    page: 25
    x_unit: "V"
    y_unit: "µV"
    conditions: "V_{CC} = 24V, V_{EE} = -24V, ALL CHANNELS"
  - file: "ad4858/curves/zero-scale-error-vs-temperature.csv"
    caption: "Figure 39. Zero-Scale Error vs. Temperature"
    figure: "ad4858/figures/ad4858-f040.png"
    page: 27
    x_unit: "°C"
    y_unit: "µV"
    conditions: "ALL CHANNELS"
agentforge:
  part_number: "AD4858"
  datasheet_revision: "0"
  repairs: 5
  reading_order: "geometry"
---

# AD4858 — Buffered, 8-Channel Simultaneous Sampling, 20-Bit 1 MSPS DAS

*Datasheet: [AD4858 data sheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/ad4858.pdf)*

—40.75V TO 0V

### [AD4858](https://www.analog.com/AD4858)

### FEATURES
<!-- page: 1 -->

- Complete 20-bit data acquisition system
- Simultaneous sampling of 8 internally buffered channels
- 1 MSPS per channel throughput
- Differential, wide common-mode range inputs
- ±75 pA typical input leakage at 25°C
- Full-scale input step settling time < 300 ns
- Integrated reference and reference buffer (4.096 V)
- Integrated supply decoupling capacitors
- 45 mW per channel at 1 MSPS, power scales with throughput
- Minimal external signal conditioning
- Seamless high dynamic range
- Per sample, per channel automatic gain ranging
- Maintains ppm-level INL
- Per channel SoftSpan input ranges, bipolar or unipolar
- ±40 V, ±25 V, ±20 V, ±12.5 V, ±10 V, ±6.25 V, ±5 V, ±2.5 V
- 0 V to 40 V, 25 V, 20 V, 12.5 V, 10 V, 6.25 V, 5 V, 2.5 V
- Rail-to-rail input overdrive tolerance
- High performance
 - INL: ±160 µV typical (±40 V range)
 - SNR: 97.2 dB single-conversion typical (±40 V range)
 - DR: 111.4 dB single-conversion typical (±40 V range)
 - THD: -117 dB typical (±40 V range)
 - CMRR: 120 dB typical
- Digital flexibility
 - SPI CMOS (0.9 V to 5.25 V) and LVDS serial input and output
 - Optional oversampling with 24-bit digital averaging
 - Optional offset, gain and phase correction
- 7.00 mm × 7.00 mm, 64-ball BGA full solution footprint

### APPLICATIONS
<!-- pages: 1-3 -->

- Automatic test equipment
- Avionics and aerospace
- Instrumentation and control systems
- Semiconductor manufacturing
- Test and measurement

### FUNCTIONAL BLOCK DIAGRAM
<!-- page: 1 -->

![Figure 1. Functional Block Diagram (Example Analog-Input Signal Use Cases Shown)](ad4858/figures/ad4858-f002.png)

*Figure 1. Functional Block Diagram (Example Analog-Input Signal Use Cases Shown)*







### TABLE OF CONTENTS

- Features
- Applications
- Functional Block Diagram
- General Description
 - Companion Products
- Specifications
 - Timing Specifications
- Absolute Maximum Ratings
 - Junction Temperature
 - Thermal Resistance
 - Electrostatic Discharge (ESD) Ratings
 - ESD Caution
- Pin Configuration and Function Descriptions
- Typical Performance Characteristics
- Terminology
- Theory of Operation
 - Overview
 - Converter Operation
 - Transfer Function
 - SoftSpan
 - Seamless High Dynamic Range
 - Digital Processing Features
- Applications Information
 - Buffered Analog Inputs
 - Analog Input Drive Circuits
 - Analog Input Overdrive Tolerance
 - Analog Input Filtering
 - DAS Reference
 - Power Considerations
 - Timing and Control
- Digital Interface
 - CMOS Conversion Data Output Mode
 - LVDS Conversion Data Output Mode
 - Packet Format
 - SPI Register Configuration Bus
- Register Summary
- Register Details
 - SPI Configuration A Register
 - SPI Configuration B Register
 - Device Configuration Register
 - Device Type Register
 - Product ID Low Register
 - Product ID High Register
 - Device Grade Register
 - Scratch Pad Register
 - SPI Revision Register
 - Vendor ID Low Register
 - Vendor ID High Register
 - Loop Configuration A Register
 - Loop Configuration B Register
 - SPI Configuration C Register
 - SPI Status Register
 - SPI Configuration D Register
 - Device Status Register
 - Channel Overrange Status Register
 - Channel Underrange Status Register
 - Register Map CRC
 - Device Control Register
 - Packet Format Register
 - Oversample Control Register
 - Seamless High Dynamic Range Register
 - Channel Sleep Register
 - Channel 0 SoftSpan Register
 - Channel 0 Offset Register
 - Channel 0 Gain Register
 - Channel 0 Phase Register
 - Channel 0 Overrange Limit Register
 - Channel 0 Underrange Limit Register
 - Channel 0 Test Pattern Register
- Outline Dimensions
 - Ordering Guide
 - Evaluation Board

### REVISION HISTORY

10/2023-Revision 0: Initial Version

### GENERAL DESCRIPTION
<!-- pages: 3-4 -->

The AD4858 is a fully buffered, 8-channel simultaneous sampling, 20-bit, 1 MSPS data acquisition system (DAS) with differential, wide common-mode range inputs. Its functional architecture is shown in Figure 1. Operating from a 5 V low voltage supply, flexible input buffer supplies, and using the precision low drift internal reference and reference buffer, the AD4858 allows the SoftSpan range of each channel to be independently configured to match the native application signal swing, minimizing additional external signal conditioning. To further maximize single-conversion dynamic range, the AD4858 incorporates seamless high dynamic range (SHDR) technology. When enabled, the input signal path gain of the channel is automatically optimized on a sample-by-sample basis, minimizing converter noise on each sample without impacting linearity.

The 11 MHz bandwidth, picoamp input analog buffers, wide input common-mode range, and 120 dB common-mode rejection ratio (CMRR) of the AD4858 allow the DAS to directly digitize input signals with arbitrary swings on INx+ and INx-. Its input signal flexibility, combined with ±160 µV integral nonlinearity (INL), no missing codes at 20 bits, 97.2 dB signal to noise ratio (SNR), and 111.4 dB dynamic range (DR), make the AD4858 an ideal choice for applications requiring high accuracy, throughput, and precision in a compact solution footprint. Enabling 24-bit oversampling offers further SNR and dynamic range improvements. Optional per channel offset, gain, and phase adjustment provide the ability to calibrate and remove system-level errors upstream to the DAS.

The AD4858 features a serial peripheral interface (SPI) register configuration bus (0.9 V to 5.25 V), and supports both low voltage differential signaling buses (LVDS) and complementary metal-oxidize semiconductor (CMOS) conversion data output buses, selectable using the LVDS/C̅M̅O̅S̅ pin. Between one and eight lines of data output can be employed in CMOS mode, allowing the user to optimize bus width and throughput.

The 7.00 mm × 7.00 mm, 64-ball, ball grid array (BGA) of the AD4858 includes all critical power supply and reference bypass capacitors, minimizing full solution footprint and component count, and reducing sensitivity to application printed circuit board (PCB) layout. It operates over an extended industrial temperature range of -40°C to +125°C.

Note that throughout this data sheet, multifunction pins such as LVDS/C̅M̅O̅S̅ are referred to either by the entire pin name or by a single function of the pin. For example, LVDS when only that function is relevant.

### COMPANION PRODUCTS
<!-- page: 3 -->

- Voltage references: LTC6655-4.096 or ADR4540

- Power solutions: LT1761, LT8330, and/or LT3042

### SPECIFICATIONS
<!-- pages: 4-18 -->

V_{EE} = -40.75 V to 0 V, V_{CC} = 7.25 V to 48 V, (V_{CC} - V_{EE} ) = 10 V to 48 V, V_{DD} = 5 V, V_{DDH} = 2.5 V, 1.8 V low drop out (LDO) regulator enabled, and V_{IO} = 0.9 V to 5.25 V. All channels convert at sampling frequency (f_{S} ) = 1 MSPS, internal reference and reference buffer enabled, all SoftSpan ranges, fully-differential input signal drive in SoftSpan 15 and SoftSpan 13, true bipolar or unipolar signal drive in other bipolar or unipolar SoftSpan ranges, and all specifications T_{MIN} to T_{MAX} , unless otherwise noted. Typical values are at T_{A} = 25°C.

**Table 1. Specifications** ([table-00-p4-spec.csv](ad4858/tables/table-00-p4-spec.csv), p. 4)

| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS |  |
|---|---|---|---|---|---|---|
| RESOLUTION |  | 20 |  |  | Bits |  |
| **ANALOG INPUTS** |  |  |  |  |  |  |
| Absolute Input Voltage | V_{INx+}[^1], V_{INx−}[^2] to V_{CC} and V_{EE} | V_{EE} + 3.2 |  | V_{CC} − 3.2 | V |  |
| **Differential Input Range** | (V_{INx+} − V_{INx−}), V_{REF}[^3] = V_{REFBUF}[^4]/1.024 |  |  |  |  |  |
|  | SoftSpan 15: ±10 × V_{REF} range | −10 × V_{REF} |  | +10 × V_{REF} | V |  |
|  | SoftSpan 14: 0 to 10 × V_{REF} range | 0 |  | 10 × V_{REF} | V |  |
|  | SoftSpan 13: ±6.25 × V_{REF} range | −6.25 × V_{REF} |  | +6.25 × V_{REF} | V |  |
|  | SoftSpan 12: 0 to 6.25 × V_{REF} range | 0 |  | 6.25 × V_{REF} | V |  |
|  | SoftSpan 11: ±5 × V_{REF} range | −5 × V_{REF} |  | +5 × V_{REF} | V |  |
|  | SoftSpan 10: 0 to 5 × V_{REF} range | 0 |  | 5 × V_{REF} | V |  |
|  | SoftSpan 9: ±3.125 × V_{REF} range | −3.125 × V_{REF} |  | +3.125 × V_{REF} | V |  |
|  | SoftSpan 8: 0 to 3.125 × V_{REF} range | 0 |  | 3.125 × V_{REF} | V |  |
|  | SoftSpan 7: ±2.5 × V_{REF} range | −2.5 × V_{REF} |  | +2.5 × V_{REF} | V |  |
|  | SoftSpan 6: 0 to 2.5 × V_{REF} range | 0 |  | 2.5 × V_{REF} | V |  |
|  | SoftSpan 5: ±1.5625 × V_{REF} range | −1.5625 × V_{REF} |  | +1.5625 × V_{REF} | V |  |
|  | SoftSpan 4: 0 to 1.5625 × V_{REF} range | 0 |  | 1.5625 × V_{REF} | V |  |
|  | SoftSpan 3: ±1.25 × V_{REF} range | −1.25 × V_{REF} |  | +1.25 × V_{REF} | V |  |
|  | SoftSpan 2: 0 to 1.25 × V_{REF} range | 0 |  | 1.25 × V_{REF} | V |  |
|  | SoftSpan 1: ±0.625 × V_{REF} range | −0.625 × V_{REF} |  | +0.625 × V_{REF} | V |  |
|  | SoftSpan 0: 0 to 0.625 × V_{REF} range | 0 |  | 0.625 × V_{REF} | V |  |
| Common-Mode Input Range | V_{CM}[^5] = (V_{INx+} + V_{INx−})/2 | V_{EE} + 3.2 |  | V_{CC} − 3.2 | V |  |
| CMRR | V_{CM} = 36 V p-p 200 Hz sine | 100 | 120 |  | dB |  |
| Differential Input Overdrive Tolerance[^6] | (V_{INx+} − V_{INx−}) | −(V_{CC} − V_{EE}) |  | (V_{CC} − V_{EE}) | V |  |
| Input Overdrive Current Tolerance[^6] | V_{INx+}, V_{INx−} > V_{CC} |  |  | 10 | mA |  |
|  | V_{INx+}, V_{INx−} < V_{EE} | 0 |  |  | mA |  |
| Input Leakage Current | V_{INx+}, V_{INx−} = V_{CC} to V_{EE} | −40 | ±0.075 | +40 | nA |  |
| Input Resistance | R_{INx+}[^7], R_{INx−}[^8] for each pin |  | 1000 |  | GΩ |  |
| Input Capacitance | C_{INx+}[^9], C_{INx−}[^10] for each pin |  | 4 |  | pF |  |
| **DC ACCURACY** |  |  |  |  |  |  |
| No Missing Codes |  | 20 |  |  | Bits |  |
| INL Error | SHDR on |  |  |  |  |  |
|  | SoftSpan 15 and SoftSpan 14: ±40 V and 0 V to 40 V ranges | −725 | ±160 | +725 | µV |  |
|  | SoftSpan 13 and SoftSpan 12: ±25 V and 0 V to 25 V ranges | −400 | ±100 | +400 | µV |  |
|  | SoftSpan 11 and SoftSpan 10: ±20 V and 0 V to 20 V ranges | −400 | ±100 | +400 | µV |  |
|  | SoftSpan 9 and SoftSpan 8: ±12.5 V and 0 V to 12.5 V ranges | −275 | ±50 | +275 | µV |  |
|  | SoftSpan 7 and SoftSpan 6: ±10 V and 0 V to 10 V ranges | −220 | ±50 | +220 | µV |  |
|  | SoftSpan 5 and SoftSpan 4: ±6.25 V and 0 V to 6.25 V ranges | −120 | ±25 | +120 | µV |  |
|  | SoftSpan 3 and SoftSpan 2: ±5 V and 0 V to 5 V ranges | −100 | ±25 | +100 | µV |  |
|  | SoftSpan 1 and SoftSpan 0: ±2.5 V and 0 V to 2.5 V ranges | −55 | ±15 | +55 | µV |  |
| Differential Nonlinearity (DNL) Error |  | −0.9 | ±0.2 |  | LSB |  |
| Transition Noise[^11] | SHDR on, near zero-scale |  | 73 |  | µV RMS |  |
|  | SHDR off, near zero-scale |  |  |  |  |  |
|  | SoftSpan 15 and SoftSpan 14: ±40 V and 0 V to 40 V ranges |  | 461 |  | µV RMS |  |
|  | SoftSpan 13 and SoftSpan 12: ±25 V and 0 V to 25 V ranges |  | 287 |  | µV RMS |  |
|  | SoftSpan 11 and SoftSpan 10: ±20 V and 0 V to 20 V ranges |  | 241 |  | µV RMS |  |
|  | SoftSpan 9 and SoftSpan 8: ±12.5 V and 0 V to 12.5 V ranges |  | 155 |  | µV RMS |  |
|  | SoftSpan 7 and SoftSpan 6: ±10 V and 0 V to 10 V ranges |  | 133 |  | µV RMS |  |
|  | SoftSpan 5 and SoftSpan 4: ±6.25 V and 0 V to 6.25 V ranges |  | 94 |  | µV RMS |  |
|  | SoftSpan 3 and SoftSpan 2: ±5 V and 0 V to 5 V ranges |  | 81 |  | µV RMS |  |
|  | SoftSpan 1 and SoftSpan 0: ±2.5 V and 0 V to 2.5 V ranges |  | 73 |  | µV RMS |  |
| Zero-Scale Error |  | −700 | ±100 | +700 | µV |  |
| Zero-Scale Error Drift |  |  | ±1.5 |  | µV/°C |  |
| Full-Scale Error[^12] | V_{REFIO} = 4.096 V, REFIO overdriven[^13] | −0.035 | ±0.01 | +0.035 | %FS |  |
| Full-Scale Error Drift[^12] | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | ±1.5 |  | ppm/°C |  |
| **AC ACCURACY[^14]** |  |  |  |  |  |  |
| **Dynamic Range (DR)** | SHDR on/off |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range |  | 111.4/95.8 |  | dB |  |
|  | SoftSpan 14: 0 V to 40 V range |  | 105.4/89.8 |  | dB |  |
|  | SoftSpan 13: ±25 V range |  | 107.6/95.8 |  | dB |  |
|  | SoftSpan 12: 0 V to 25 V range |  | 101.6/89.8 |  | dB |  |
|  | SoftSpan 11: ±20 V range |  | 105.7/95.4 |  | dB |  |
|  | SoftSpan 10: 0 V to 20 V range |  | 99.7/89.4 |  | dB |  |
|  | SoftSpan 9: ±12.5 V range |  | 101.6/95.1 |  | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range |  | 95.6/89.1 |  | dB |  |
|  | SoftSpan 7: ±10 V range |  | 99.7/94.5 |  | dB |  |
|  | SoftSpan 6: 0 V to 10 V range |  | 93.7/88.5 |  | dB |  |
|  | SoftSpan 5: ±6.25 V range |  | 95.7/93.4 |  | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range |  | 89.7/87.4 |  | dB |  |
|  | SoftSpan 3: ±5 V range |  | 93.7/92.7 |  | dB |  |
|  | SoftSpan 2: 0 V to 5 V range |  | 87.7/86.7 |  | dB |  |
|  | SoftSpan 1: ±2.5 V range |  | 87.7/87.7 |  | dB |  |
|  | SoftSpan 0: 0 V to 2.5 V range |  | 81.7/81.7 |  | dB |  |
| Oversampled Dynamic Range | OSR = 2 |  | DR + 3 |  | dB |  |
|  | OSR = 32 |  | DR + 15 |  | dB |  |
|  | OSR = 1024 |  | DR + 27 |  | dB |  |
| **Signal-to-Noise-and-Distortion (SINAD) Ratio** | SHDR on, f_{IN} = 1 kHz, −1 dBFS |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range | 90.9 | 97.2 |  | dB |  |
|  | SoftSpan 14: 0 V to 40 V range | 85.3 | 92 |  | dB |  |
|  | SoftSpan 13: ±25 V range | 92.6 | 97.4 |  | dB |  |
|  | SoftSpan 12: 0 V to 25 V range | 86.4 | 92.0 |  | dB |  |
|  | SoftSpan 11: ±20 V range | 93.5 | 97.9 |  | dB |  |
|  | SoftSpan 10: 0 V to 20 V range | 87.2 | 92.0 |  | dB |  |
|  | SoftSpan 9: ±12.5 V range | 94.3 | 97.2 |  | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range | 88.2 | 91.5 |  | dB |  |
|  | SoftSpan 7: ±10 V range | 94.1 | 96.6 |  | dB |  |
|  | SoftSpan 6: 0 V to 10 V range | 88.1 | 90.9 |  | dB |  |
|  | SoftSpan 5: ±6.25 V range | 92.4 | 94.6 |  | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range | 86.8 | 88.7 |  | dB |  |
|  | SoftSpan 3: ±5 V range | 91.1 | 93.1 |  | dB |  |
|  | SoftSpan 2: 0 V to 5 V range | 85.4 | 87.3 |  | dB |  |
|  | SoftSpan 1: ±2.5 V range | 85.3 | 87.3 |  | dB |  |
|  | SoftSpan 0: 0 V to 2.5 V range | 79.7 | 81.6 |  | dB |  |
|  | SHDR off, f_{IN} = 1 kHz, −1 dBFS |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range | 93.1 | 95.3 |  | dB |  |
|  | SoftSpan 14: 0 V to 40 V range | 87.1 | 89.4 |  | dB |  |
|  | SoftSpan 13: ±25 V range | 93.2 | 95.3 |  | dB |  |
|  | SoftSpan 12: 0 V to 25 V range | 87.3 | 89.4 |  | dB |  |
|  | SoftSpan 11: ±20 V range | 92.9 | 95.0 |  | dB |  |
|  | SoftSpan 10: 0 V to 20 V range | 86.9 | 89.0 |  | dB |  |
|  | SoftSpan 9: ±12.5 V range | 92.6 | 94.7 |  | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range | 86.7 | 88.8 |  | dB |  |
|  | SoftSpan 7: ±10 V range | 92.2 | 94.2 |  | dB |  |
|  | SoftSpan 6: 0 V to 10 V range | 86.2 | 88.2 |  | dB |  |
|  | SoftSpan 5: ±6.25 V range | 91.2 | 93.1 |  | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range | 85.4 | 87.2 |  | dB |  |
|  | SoftSpan 3: ±5 V range | 90.3 | 92.3 |  | dB |  |
|  | SoftSpan 2: 0 V to 5 V range | 84.6 | 86.5 |  | dB |  |
|  | SoftSpan 1: ±2.5 V range | 85.3 | 87.4 |  | dB |  |
|  | SoftSpan 0: 0 V to 2.5 V range | 79.7 | 81.6 |  | dB |  |
| **Signal-to-Noise Ratio (SNR)** | SHDR on, f_{IN} = 1 kHz, −1 dBFS |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range | 90.9 | 97.2 |  | dB |  |
|  | SoftSpan 14: 0 V to 40 V range | 85.3 | 92.0 |  | dB |  |
|  | SoftSpan 13: ±25 V range | 92.6 | 97.4 |  | dB |  |
|  | SoftSpan 12: 0 V to 25 V range | 86.4 | 92.0 |  | dB |  |
|  | SoftSpan 11: ±20 V range | 93.6 | 97.9 |  | dB |  |
|  | SoftSpan 10: 0 V to 20 V range | 87.2 | 92.0 |  | dB |  |
|  | SoftSpan 9: ±12.5 V range | 94.3 | 97.2 |  | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range | 88.2 | 91.5 |  | dB |  |
|  | SoftSpan 7: ±10 V range | 94.1 | 96.6 |  | dB |  |
|  | SoftSpan 6: 0 V to 10 V range | 88.1 | 90.9 |  | dB |  |
|  | SoftSpan 5: ±6.25 V range | 92.5 | 94.6 |  | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range | 86.8 | 88.7 |  | dB |  |
|  | SoftSpan 3: ±5 V range | 91.2 | 93.1 |  | dB |  |
|  | SoftSpan 2: 0 V to 5 V range | 85.5 | 87.3 |  | dB |  |
|  | SoftSpan 1: ±2.5 V range | 85.4 | 87.3 |  | dB |  |
|  | SoftSpan 0: 0 V to 2.5V range | 79.8 | 81.6 |  | dB |  |
|  | SHDR off, f_{IN} = 1 kHz, −1 dBFS |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range | 93.2 | 95.3 |  | dB |  |
|  | SoftSpan 14: 0 V to 40 V range | 87.1 | 89.4 |  | dB |  |
|  | SoftSpan 13: ±25 V range | 93.2 | 95.3 |  | dB |  |
|  | SoftSpan 12: 0 V to 25 V range | 87.3 | 89.4 |  | dB |  |
|  | SoftSpan 11: ±20 V range | 92.9 | 95.0 |  | dB |  |
|  | SoftSpan 10: 0 V to 20 V range | 86.9 | 89.0 |  | dB |  |
|  | SoftSpan 9: ±12.5 V range | 92.7 | 94.7 |  | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range | 86.8 | 88.8 |  | dB |  |
|  | SoftSpan 7: ±10 V range | 92.2 | 94.2 |  | dB |  |
|  | SoftSpan 6: 0 V to 10 V range | 86.2 | 88.2 |  | dB |  |
|  | SoftSpan 5: ±6.25 V range | 91.2 | 93.1 |  | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range | 85.4 | 87.2 |  | dB |  |
|  | SoftSpan 3: ±5 V range | 90.4 | 92.3 |  | dB |  |
|  | SoftSpan 2: 0 V to 5 V range | 84.7 | 86.5 |  | dB |  |
|  | SoftSpan 1: ±2.5 V range | 85.4 | 87.4 |  | dB |  |
|  | SoftSpan 0: 0 V to 2.5 V range | 79.8 | 81.6 |  | dB |  |
| **Total Harmonic Distortion (THD)** | f_{IN} = 1 kHz, −1 dBFS |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range |  | −117 | −99 | dB |  |
|  | SoftSpan 14: 0 V to 40 V range |  | −109 | −95 | dB |  |
|  | SoftSpan 13: ±25 V range |  | −117 | −100 | dB |  |
|  | SoftSpan 12: 0 V to 25 V range |  | −111 | −98 | dB |  |
|  | SoftSpan 11: ±20 V range |  | −114 | −99 | dB |  |
|  | SoftSpan 10: 0 V to 20 V range |  | −112 | −99 | dB |  |
|  | SoftSpan 9: ±12.5 V range |  | −114 | −100 | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range |  | −113 | −100 | dB |  |
|  | SoftSpan 7: ±10 V range |  | −115 | −100 | dB |  |
|  | SoftSpan 6: 0 V to 10 V range |  | −113 | −100 | dB |  |
|  | SoftSpan 5: ±6.25 V range |  | −115 | −99 | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range |  | −113 | −99 | dB |  |
|  | SoftSpan 3: ±5 V range |  | −114 | −97 | dB |  |
|  | SoftSpan 2: 0 V to 5 V range |  | −113 | −97 | dB |  |
|  | SoftSpan 1: ±2.5 V range |  | −109 | −92 | dB |  |
|  | SoftSpan 0: 0 V to 2.5 V range |  | −110 | −92 | dB |  |
| **Spurious Free Dynamic Range (SFDR)** | f_{IN} = 1 kHz, −1 dBFS |  |  |  |  |  |
|  | SoftSpan 15: ±40 V range | 101 | 119 |  | dB |  |
|  | SoftSpan 14: 0 V to 40 V range | 99 | 113 |  | dB |  |
|  | SoftSpan 13: ±25 V range | 101 | 119 |  | dB |  |
|  | SoftSpan 12: 0 V to 25 V range | 103 | 115 |  | dB |  |
|  | SoftSpan 11: ±20 V range | 103 | 119 |  | dB |  |
|  | SoftSpan 10: 0 V to 20 V range | 103 | 116 |  | dB |  |
|  | SoftSpan 9: ±12.5 V range | 104 | 119 |  | dB |  |
|  | SoftSpan 8: 0 V to 12.5 V range | 104 | 116 |  | dB |  |
|  | SoftSpan 7: ±10 V range | 105 | 119 |  | dB |  |
|  | SoftSpan 6: 0 V to 10 V range | 105 | 116 |  | dB |  |
|  | SoftSpan 5: ±6.25 V range | 103 | 118 |  | dB |  |
|  | SoftSpan 4: 0 V to 6.25 V range | 103 | 117 |  | dB |  |
|  | SoftSpan 3: ±5 V range | 101 | 117 |  | dB |  |
|  | SoftSpan 2: 0 V to 5 V range | 101 | 117 |  | dB |  |
|  | SoftSpan 1: ±2.5 V range | 96 | 111 |  | dB |  |
|  | SoftSpan 0: 0 V to 2.5 V range | 96 | 113 |  | dB |  |
| Channel-to-Channel Crosstalk | All channels converting[^15] |  | −120 |  | dB |  |
| −3 dB Small-Signal Input Bandwidth |  |  | 11 |  | MHz |  |
| Aperture Delay |  |  | 1 |  | ns |  |
| Aperture Delay Matching |  |  | 300 |  | ps |  |
| Aperture Jitter |  |  | 1 |  | ps RMS |  |
| Transient Response | Full-scale step, 50 ppm settling |  | 300 |  | ns |  |
| **INTERNAL REFERENCE ENABLED** |  |  |  |  |  |  |
| Internal Reference Output Voltage (V_{REFIO}) | T_{A} = 25°C | 4.093 | 4.096 | 4.099 | V |  |
| Internal Reference Temperature Coefficient[^16] |  | −10 | ±2 | +10 | ppm/°C |  |
| Internal Reference Line Regulation | V_{DD} = 4.75 V to 5.25 V |  | 50 |  | µV/V |  |
| REFIO Output Resistance |  |  | 58 |  | Ω |  |
| REFIO Output Capacitance |  |  | 10 |  | nF |  |
| **INTERNAL REFERENCE DISABLED** | REFIO overdriven[^13] |  |  |  |  |  |
| REFIO Input Voltage (V_{REFIO}) |  | 4.071 | 4.096 | 4.121 | V |  |
| REFIO Input Resistance |  |  | 38 |  | kΩ |  |
| REFIO Input Capacitance |  |  | 10 |  | nF |  |
| **REFERENCE BUFFER ENABLED** |  |  |  |  |  |  |
| Reference Buffer Offset Voltage (V_{OS}) | V_{OS} = (V_{REFBUF} − V_{REFIO}), T_{A} = 25°C | −100 | ±20 | +100 | µV |  |
| Reference Buffer Offset Voltage Drift |  |  | ±0.5 |  | µV/°C |  |
| **REFERENCE BUFFER DISABLED** | REFBUF overdriven[^17] |  |  |  |  |  |
| REFBUF Input Voltage (V_{REFBUF}) |  | 4.071 | 4.096 | 4.121 | V |  |
| REFBUF Input Current (I_{REFBUF})[^18] | V_{REFBUF} = 4.096 V, f_{S} = 1 MSPS |  | 3.3 | 4.5 | mA |  |
|  | V_{REFBUF} = 4.096 V, not converting |  | 2.2 |  | mA |  |
| **SCALED REFERENCE OUTPUT** |  |  |  |  |  |  |
| REF2500 Output Voltage (V_{REF2500}) | T_{A} = 25°C | 2.497 | 2.5 | 2.503 | V |  |
| REF2500 Temperature Coefficient[^16] |  | −10 | ±2 | +10 | ppm/°C |  |
| REF2500 Output Resistance |  |  | 26 |  | kΩ |  |
| **CMOS DIGITAL INPUTS** |  |  |  |  |  |  |
| Input Voltage High (V_{IH}) |  |  |  |  |  |  |
| CNV |  | 0.8 |  |  | V |  |
| HIVIO/L̅O̅V̅I̅O̅ |  | 4 |  |  | V |  |
| All Other Pins |  | 0.85 × V_{IO} |  |  | V |  |
| Input Voltage Low (V_{IL}) |  |  |  |  |  |  |
| CNV |  |  |  | 0.4 | V |  |
| HIVIO/L̅O̅V̅I̅O̅ |  |  |  | 1 | V |  |
| All Other Pins |  |  |  | 0.15 × V_{IO} | V |  |
| Digital Input Current (I_{IN}) |  |  |  |  |  |  |
| CNV |  | −100 |  | +100 | µA |  |
| HIVIO/L̅O̅V̅I̅O̅ |  | −10 |  | +10 | µA |  |
| All Other Pins |  | −10 |  | +10 | µA |  |
| Digital Input Capacitance (C_{IN}) |  |  | 2 |  | pF |  |
| **CMOS DIGITAL OUTPUTS** |  |  |  |  |  |  |
| Output Voltage High (V_{OH}) | Source current (I_{SOURCE}) = 500 µA | V_{IO} − 0.2 |  |  | V |  |
| Output Voltage Low (V_{OL}) | Sink current (I_{SINK}) = 500 µA |  |  | 0.2 | V |  |
| High-Z Output Leakage Current (I_{OZ}) |  | −10 |  | +10 | µA |  |
| **LVDS DIGITAL INPUTS** |  |  |  |  |  |  |
| Differential Input Voltage (V_{ID}) |  | ±200 | ±350 | ±600 | mV |  |
| Differential Termination Resistance (R_{ID}) | C̅S̅ = 0 V, V_{ICM} = 1.2 V, termination enabled[^19] | 95 | 107 | 120 | Ω |  |
| Differential Termination Resistance (R_{ID}) | C̅S̅ = V_{IO} or termination disabled[^19] |  | 10 |  | MΩ |  |
| Common-Mode Input Voltage (V_{ICM}) | 1.71 V ≤ V_{IO} < 2.5 V | 0.3 | 1.2 | V_{IO} − 0.3 | V |  |
| Common-Mode Input Voltage (V_{ICM}) | 2.5 V ≤ V_{IO} ≤ 5.25V | 0.3 | 1.2 | 2.2 | V |  |
| Common-Mode Input Current (I_{ICM}) |  | −10 |  | +10 | µA |  |
| **LVDS DIGITAL OUTPUTS** |  |  |  |  |  |  |
| Differential Output Voltage (V_{OD}) | 100 Ω differential termination, full-bias mode[^19] | ±260 | ±330 | ±400 | mV |  |
| Differential Output Voltage (V_{OD}) | 100 Ω differential termination, half-bias mode[^19] | ±135 | ±185 | ±235 | mV |  |
| Common-Mode Output Voltage (V_{OCM}) | 100 Ω differential termination | 1.1 | 1.25 | 1.4 | V |  |
| High-Z Output Leakage Current (I_{OZ}) |  | −10 |  | +10 | µA |  |
| **POWER SUPPLY VOLTAGES** |  |  |  |  |  |  |
| V_{CC} |  | 7.25 |  | 48 | V |  |
| V_{EE} |  | −40.75 |  | 0 | V |  |
| V_{CC} − V_{EE} |  | 10 |  | 48 | V |  |
| V_{DD} |  | 4.75 | 5.0 | 5.25 | V |  |
| V_{DDH} | Disables 1.8 V LDO regulator |  | 0 |  | V |  |
| V_{DDH} | Enables 1.8 V LDO regulator | 2.2 |  | 5.25 | V |  |
| V_{DDL} | Supplied externally, 1.8 V LDO regulator disabled | 1.71 | 1.8 | 1.89 | V |  |
| V_{DDL} | Supplied by 1.8 V LDO regulator, no external connection |  | 1.8 |  | V |  |
| **V_{IO}** |  |  |  |  |  |  |
| CMOS Conversion Data Output | HIVIO/L̅O̅V̅I̅O̅ = V_{DD} | 1.71 |  | 5.25 | V |  |
| CMOS Conversion Data Output | HIVIO/L̅O̅V̅I̅O̅ = GND | 0.9 |  | 1.89 | V |  |
| LVDS Conversion Data Output | HIVIO/L̅O̅V̅I̅O̅ = V_{DD} | 1.71 |  | 5.25 | V |  |
| LVDS Conversion Data Output | HIVIO/L̅O̅V̅I̅O̅ = GND | 1.71 |  | 1.89 | V |  |
| **POWER SUPPLY CURRENTS** |  |  |  |  |  |  |
| **CMOS Conversion Data Output Operating Mode[^20]** | 25 pF load on CMOS outputs, f_{S} = 1 MSPS, all channels converting |  |  |  |  |  |
| V_{CC} Current (I_{VCC}) | V_{CC} = +24 V, V_{EE} = −24 V |  | 14.9 | 19.6 | mA |  |
| V_{CC} Current (I_{VCC}) | V_{CC} = +15 V, V_{EE} = −15 V |  | 13 |  | mA |  |
| V_{CC} Current (I_{VCC}) | V_{CC} = +8.2 V, V_{EE} = −3.2 V |  | 10.7 |  | mA |  |
| V_{EE} Current (I_{VEE}) | V_{CC} = +24 V, V_{EE} = −24 V | −16.9 | −12 |  | mA |  |
| V_{EE} Current (I_{VEE}) | V_{CC} = +15 V, V_{EE} = −15 V |  | −10.2 |  | mA |  |
| V_{EE} Current (I_{VEE}) | V_{CC} = +8.2 V, V_{EE} = −3.2 V |  | −8 |  | mA |  |
| V_{DD} Current (I_{VDD}) | Reference and reference buffer enabled |  | 15.2 | 22.3 | mA |  |
| V_{DD} Current (I_{VDD}) | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | 13.2 |  | mA |  |
| V_{DD} Current (I_{VDD}) | V_{REFBUF} = 4.096 V, REFBUF overdriven[^17] |  | 3.7 |  | mA |  |
| V_{DDH} Current (I_{VDDH}) | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 57 | 78 | mA |  |
| V_{DDL} Current (I_{VDDL}) | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 55 | 76 | mA |  |
| V_{IO} Current (I_{VIO}) | V_{IO} = 2.5 V |  | 5.5 | 7.3 | mA |  |
| Acquisition Mode |  |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 9.4 |  | mA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V |  | −7.4 |  | mA |  |
| I_{VDD} | Reference and reference buffer enabled |  | 10.8 |  | mA |  |
| I_{VDD} | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | 8.8 |  | mA |  |
| I_{VDD} | V_{REFBUF} = 4.096 V, REFBUF overdriven[^17] |  | 1.4 |  | mA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 72 |  | µA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 16 |  | µA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 1 |  | µA |  |
| Nap Mode |  |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 4.5 |  | mA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V |  | −3.3 |  | mA |  |
| I_{VDD} | Reference and reference buffer enabled |  | 10.3 |  | mA |  |
| I_{VDD} | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | 8.3 |  | mA |  |
| I_{VDD} | V_{REFBUF} = 4.096 V, REFBUF overdriven[^17] |  | 1.0 |  | mA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 72 |  | µA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 16 |  | µA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 1 |  | µA |  |
| Power-Down Mode |  |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 18 |  | µA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V |  | −4 |  | µA |  |
| I_{VDD} |  |  | 130 |  | µA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 30 |  | µA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 16 |  | µA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 1 |  | µA |  |
| **LVDS Conversion Data Output** | 100 Ω differential load on LVDS outputs |  |  |  |  |  |
| Operating Mode | f_{S} = 1 MSPS, all channels converting |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 14.9 | 19.6 | mA |  |
| I_{VCC} | V_{CC} = +15 V, V_{EE} = −15 V |  | 13 |  | mA |  |
| I_{VCC} | V_{CC} = +8.2 V, V_{EE} = −3.2 V |  | 10.7 |  | mA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V | −16.9 | −12 |  | mA |  |
| I_{VEE} | V_{CC} = +15 V, V_{EE} = −15 V |  | −10.2 |  | mA |  |
| I_{VEE} | V_{CC} = +8.2 V, V_{EE} = −3.2 V |  | −8 |  | mA |  |
| I_{VDD} | Reference and reference buffer enabled |  | 18.8 | 25.9 | mA |  |
| I_{VDD} | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | 16.8 |  | mA |  |
| I_{VDD} | V_{REFBUF} = 4.096 V, REFBUF overdriven[^17] |  | 7.3 |  | mA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 67 | 89 | mA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 65 | 87 | mA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 82 | 165 | µA |  |
| Acquisition Mode |  |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 9.4 |  | mA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V |  | −7.4 |  | mA |  |
| I_{VDD} | Reference and reference buffer enabled |  | 11.6 |  | mA |  |
|  | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | 9.6 |  | mA |  |
|  | V_{REFBUF} = 4.096 V, REFBUF overdriven[^17] |  | 2.2 |  | mA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 8.4 |  | mA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 8.3 |  | mA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 1 |  | µA |  |
| Nap Mode |  |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 4.5 |  | mA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V |  | −3.3 |  | mA |  |
| I_{VDD} | Reference and reference buffer enabled |  | 11.1 |  | mA |  |
|  | V_{REFIO} = 4.096 V, REFIO overdriven[^13] |  | 9.1 |  | mA |  |
|  | V_{REFBUF} = 4.096 V, REFBUF overdriven[^17] |  | 1.8 |  | mA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 8.4 |  | mA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 8.3 |  | mA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 1 |  | µA |  |
| Power-Down Mode |  |  |  |  |  |  |
| I_{VCC} | V_{CC} = +24 V, V_{EE} = −24 V |  | 18 |  | µA |  |
| I_{VEE} | V_{CC} = +24 V, V_{EE} = −24 V |  | −4 |  | µA |  |
| I_{VDD} |  |  | 130 |  | µA |  |
| I_{VDDH} | V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled |  | 30 |  | µA |  |
| I_{VDDL} | V_{DDH} = GND, 1.8 V LDO regulator disabled, V_{DDL} = 1.8 V |  | 16 |  | µA |  |
| I_{VIO} | V_{IO} = 2.5 V |  | 1 |  | µA |  |
| **POWER DISSIPATION** | Reference and reference buffer enabled, V_{DDH} = 2.5 V, 1.8 V LDO regulator enabled, V_{IO} = 2.5 V |  |  |  |  |  |
| **CMOS Conversion Data Output** | 25 pF load on CMOS outputs |  |  |  |  |  |
| **Operation Mode** | f_{S} = 1 MSPS, all channels converting |  |  |  |  |  |
|  | V_{CC} = +24 V, V_{EE} = −24 V |  | 878 | 1201 | mW |  |
|  | V_{CC} = +15 V, V_{EE} = −15 V |  | 580 |  | mW |  |
|  | V_{CC} = +8.2 V, V_{EE} = −3.2 V |  | 346 |  | mW |  |
| Acquisition Mode | V_{CC} = +24 V, V_{EE} = −24 V |  | 457 |  | mW |  |
| Nap Mode | V_{CC} = +24 V, V_{EE} = −24 V |  | 239 |  | mW |  |
| Power-Down Mode | V_{CC} = +24 V, V_{EE} = −24 V |  | 1.3 |  | mW |  |
| **LVDS Conversion Data Output** | 100 Ω differential load on LVDS outputs |  |  |  |  |  |
| **Operation Mode** | f_{S} = 1 MSPS, all channels converting |  |  |  |  |  |
|  | V_{CC} = +24 V, V_{EE} = −24 V |  | 907 | 1228 | mW |  |
|  | V_{CC} = +15 V, V_{EE} = −15 V |  | 610 |  | mW |  |
|  | V_{CC} = +8.2 V, V_{EE} = −3.2 V |  | 375 |  | mW |  |
| Acquisition Mode | V_{CC} = +24 V, V_{EE} = −24 V |  | 482 |  | mW |  |
| Nap Mode | V_{CC} = +24 V, V_{EE} = −24 V |  | 264 |  | mW |  |
| Power-Down Mode | V_{CC} = +24 V, V_{EE} = −24 V |  | 1.3 |  | mW |  |
| **OPERATING TEMPERATURE RANGE[^21]** |  |  |  |  |  |  |
| T_{MIN} |  | −40 |  |  | °C |  |
| T_{MAX} |  |  |  | +125 | °C |  |

- **Note 1:** Positive analog-input pin voltage.
- **Note 2:** Negative analog-input pin voltage.
- **Note 3:** REFBUF pin voltage scaled by (1/1.024), nominally 4 V.
- **Note 4:** REFBUF pin voltage, nominally 4.096 V.
- **Note 5:** Common-mode voltage of the positive analog-input pin and the negative analog-input pin.
- **Note 6:** Exceeding these limits on any channel may corrupt conversion results on other channels. Driving an analog input greater than V_{CC} on any channel up to 10 mA does not affect conversion results on other channels. Driving an analog input less than V_{EE} may corrupt conversion results on other channels. Refer to the Analog Input Overdrive Tolerance section for further details. Refer to the Absolute Maximum Ratings section for pin voltage and current limits related to device reliability.
- **Note 7:** Positive analog-input pin resistance.
- **Note 8:** Negative analog-input pin resistance.
- **Note 9:** Positive analog-input pin capacitance.
- **Note 10:** Negative analog-input pin capacitance
- **Note 11:** A plot of the input-referred noise vs. the differential input level with SHDR on and off is shown in Figure 18.
- **Note 12:** These specifications are measured while externally supplying V_{REFIO} = 4.096 V with the internal band-gap reference powered down. The specifications do not include nominal value or the temperature drift terms associated with the internal band-gap.
- **Note 13:** When REFIO is overdriven, the internal band-gap reference must be disabled using the Device Control Register.
- **Note 14:** All specifications in dB are referred to a full-scale input in the relevant SoftSpan input range, except for crosstalk, which is referred to the crosstalk injection signal amplitude, and the THD, which is referred to the fundamental input signal amplitude.
- **Note 15:** Sine wave at frequency on injection channel (f_{INJ}) = 100 kHz and second sine wave at frequency on receiver channels (f_{RCV}) = 1 kHz.
- **Note 16:** Temperature coefficient is calculated by dividing the maximum change in the output voltage by the specified temperature range (T_{MAX} − T_{MIN}).
- **Note 17:** When REFBUF is overdriven, the internal band-gap reference and reference buffer must be disabled using the Device Control Register.
- **Note 18:** I_{REFBUF} varies proportionally with the sample rate and the number of active channels.
- **Note 19:** Enable or disable the LVDS termination resistance and half-bias mode using the Device Control Register.
- **Note 20:** A plot of the CMOS operating mode currents vs. sample rate is shown in Figure 33.
- **Note 21:** Refer to the Absolute Maximum Ratings section and the Junction Temperature section for the junction temperature limits related to device reliability.

### TIMING SPECIFICATIONS
<!-- page: 13 -->

V_{EE} = -40.75 V to 0 V, V_{CC} = 7.25 V to 48 V, (V_{CC} - V_{EE} ) = 10 V to 48 V, V_{DD} = 5 V, V_{DDH} = 2.5 V, 1.8 V_{LDO} regulator enabled, and V_{IO} = 0.9 V to 5.25 V. All channels converting at f_{S} = 1 MSPS, internal reference and reference buffer enabled, all SoftSpan ranges, fully-differential input signal drive in SoftSpan 15 and SoftSpan 13, true bipolar or unipolar signal drive in other bipolar or unipolar SoftSpan ranges, and all specifications T_{MIN} to T_{MAX} , unless otherwise noted. Typical values are at T_{A} = 25°C. Interface timing tested using a 25 pF load capacitance on CMOS outputs, a 100 Ω differential termination resistance between LVDS output differential pairs, internal termination resistance enabled on LVDS input differential pairs, LVDS full-bias mode enabled, and V_{ICM} = 1.2 V and V_{ID} = ±350 mV on LVDS input differential pairs.

**Table 2. Universal Timing** ([table-01-p13-spec.csv](ad4858/tables/table-01-p13-spec.csv), p. 13)

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| Sampling Frequency | f_{S} | 0 |  | 1 | MSPS |
| Time Between Conversions | t_{CYC} | 1 |  |  | µs |
| Conversion Time | t_{CONV} | 605 | 665 | 725 | ns |
| Acquisition Phase[^1] | t_{ACQ} | 465 |  |  | ns |
| CNV High Time | t_{CNVH} | 40 |  |  | ns |
| CNV Low Time | t_{CNVL} | 750 |  |  | ns |
| CNV Rising Edge to BUSY Rising Edge Delay | t_{DCNVBUSY} |  |  | 15 | ns |
| Data Valid to BUSY Falling Edge Delay | t_{DSDOBUSY} | 2 |  |  | ns |
| Last SCKI Edge to CNV Rising Edge | t_{SCKICNV} | 20 |  |  | ns |
| PD High Time | t_{PDH} | 40 |  |  | ns |
| PD Low Time | t_{PDL} | 40 |  |  | ns |
| Device Wake Time to Ready to Convert | t_{WAKE} |  |  | 1 | ms |
| Device Power-On-Reset Time | t_{POR} |  |  | 1 | ms |

- **Note 1:** The acquisition phase is the time available for the ADCs to acquire a new input with the DAS running at a throughput rate of 1 MSPS.

![Figure 2. Universal Timing](ad4858/figures/ad4858-f003.png)

*Figure 2. Universal Timing*

**Table 3. SPI Register Configuration Bus Read/Write Timing** ([table-02-p14-spec.csv](ad4858/tables/table-02-p14-spec.csv), p. 14)

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| C̅S̅ Low Time | t_{CSL} | 15 |  |  | ns |
| C̅S̅ High Time | t_{CSH} | 15 |  |  | ns |
| C̅S̅ Falling Edge to First CSCK Rising Edge | t_{CSCSCK} | 15 |  |  | ns |
| CSCK Period | t_{CSCK} | 40 |  |  | ns |
| CSCK Low Time | t_{CSCKL} | 16 |  |  | ns |
| CSCK High Time | t_{CSCKH} | 16 |  |  | ns |
| Last CSCK Edge to C̅S̅ Rising Edge | t_{CSCKCS} | 15 |  |  | ns |
| CSDIO Valid Setup Time to CSCK Rising Edge | t_{SCSDIOI} | 4 |  |  | ns |
| CSDIO Valid Hold Time from CSCK Rising Edge | t_{HCSDIOI} | 1 |  |  | ns |
| CSCK 16th Rising Edge to CSDIO 3-Wire Output State Delay | t_{DIO} | 2 |  | 10 | ns |
| CSCK Falling Edge to CSDIO Data Valid Delay | t_{DCSDIOO} |  |  | 11 | ns |
| CSCK Falling Edge to CSDIO Data Remains Valid | t_{HCSDIOO} | 1 |  |  | ns |
| CSCK Falling Edge to CSDO Data Valid Delay | t_{DCSDO} |  |  | 11 | ns |
| CSCK Falling Edge to CSDO Data Remains Valid | t_{HCSDO} | 1 |  |  | ns |
| C̅S̅ Falling Edge to 4-Wire Bus Low Impedance Delay | t_{DCSEN} |  |  | 15 | ns |
| C̅S̅ Rising Edge to Bus High Impedance Delay | t_{DCSDIS} |  |  | 15 | ns |

![Figure 3. SPI Register Configuration Bus Write Timing](ad4858/figures/ad4858-f004.png)

*Figure 3. SPI Register Configuration Bus Write Timing*

![Figure 4. SPI Register Configuration Bus 3-Wire Read Timing](ad4858/figures/ad4858-f005.png)

*Figure 4. SPI Register Configuration Bus 3-Wire Read Timing*

![Figure 5. SPI Register Configuration Bus 4-Wire Read Timing](ad4858/figures/ad4858-f006.png)

*Figure 5. SPI Register Configuration Bus 4-Wire Read Timing*

**Table 4. CMOS Conversion Data Output Timing** ([table-03-p16-spec.csv](ad4858/tables/table-03-p16-spec.csv), p. 16)

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| SCKI Period | t_{SCKI} | 10 |  |  | ns |
| SCKI High Time | t_{SCKIH} | 4 |  |  | ns |
| SCKI Low Time | t_{SCKIL} | 4 |  |  | ns |
| SCKI Rising Edge to SDOx Data Valid Delay | t_{DSDO} |  |  | 7.5 | ns |
| SCKI Rising Edge to SDOx Remains Valid | t_{HSDO} | 1.5 |  |  | ns |
| Skew Between SDOx Data and SCKO | t_{SKEW} | −1 | 0 | +1 | ns |
| C̅S̅ High Time | t_{CSH} | 15 |  |  | ns |
| C̅S̅ Low Time | t_{CSL} | 15 |  |  | ns |
| C̅S̅ Falling Edge to Bus Low Impedance Delay | t_{DCSEN} |  |  | 15 | ns |
| C̅S̅ Rising Edge to Bus High Impedance Delay | t_{DCSDIS} |  |  | 15 | ns |
| C̅S̅ Falling Edge to First SCKI Rising Edge | t_{CSSCKI} | 15 |  |  | ns |
| Last SCKI Edge to C̅S̅ Rising Edge | t_{SCKICS} | 15 |  |  | ns |
| Last SCKI Edge to CNV Rising Edge | t_{SCKICNV} | 20 |  |  | ns |

![Figure 6. CMOS Conversion Data Bus Timing](ad4858/figures/ad4858-f007.png)

*Figure 6. CMOS Conversion Data Bus Timing*

**Table 5. LVDS Conversion Data Output Timing** ([table-04-p17-spec.csv](ad4858/tables/table-04-p17-spec.csv), p. 17)

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|
| SCKI Period | t_{SCKI} | 2.5 |  |  | ns |
| SCKI High Time | t_{SCKIH} | 0.75 |  |  | ns |
| SCKI Low Time | t_{SCKIL} | 0.75 |  |  | ns |
| SCKI Edge to SDO Data Valid Delay | t_{DSDO} |  |  | 7.5 | ns |
| SCKI Edge to SDO Data Remains Valid | t_{HSDO} | 1.5 |  |  |  |
| SDO to SCKO Skew | t_{SKEW} | −0.25 | 0 | +0.25 | ns |
| C̅S̅ High Time | t_{CSH} | 15 |  |  | ns |
| C̅S̅ Low Time | t_{CSL} | 75 |  |  | ns |
| C̅S̅ Falling Edge to Bus Low Impedance Delay | t_{DCSEN} |  |  | 75 | ns |
| C̅S̅ Rising Edge to Bus High Impedance Delay | t_{DCSDIS} |  |  | 15 | ns |
| C̅S̅ Falling Edge to First SCKI Rising Edge | t_{CSSCKI} | 75 |  |  |  |
| Last SCKI Falling Edge to C̅S̅ Rising Edge | t_{SCKICS} | 15 |  |  |  |
| Last SCKI Edge to CNV Rising Edge | t_{SCKICNV} | 20 |  |  | ns |

![Figure 7. LVDS Conversion Data Bus Timing](ad4858/figures/ad4858-f111.png)

*Figure 7. LVDS Conversion Data Bus Timing*

### ABSOLUTE MAXIMUM RATINGS
<!-- page: 18 -->

### Table 6. Absolute Maximum Ratings
<!-- page: 18 -->

**Table 6. Absolute Maximum Ratings** ([table-05-p18-abs_max.csv](ad4858/tables/table-05-p18-abs_max.csv), p. 18)

| PARAMETER | RATING |
|---|---|
| **Analog Input and Output Voltages** |  |
| IN0+ to IN7+ and IN0− to IN7− | (V_{EE} − 0.3 V) to (V_{CC} + 0.3 V) |
| REFIO, REFBUF, and REF2500 to GND | −0.3 V to (V_{DD} + 0.3 V) |
| **Supply Voltages** |  |
| V_{CC} to GND | −0.3 V to (V_{EE} + 50.4 V) |
| V_{EE} to GND | (V_{CC} − 50.4 V) to +0.3 V |
| V_{CC} to V_{EE} | 50.4 V |
| V_{DD} and V_{DDH} to GND | −0.3 V to +6 V |
| V_{DDL} to GND | −0.3 V to +2.1 V |
| **V_{IO} to GND[^1]** |  |
| HIVIO/L̅O̅V̅I̅O̅ = GND | −0.3 V to +2.1 V |
| HIVIO/L̅O̅V̅I̅O̅ = V_{DD} | −0.3 V to +6 V |
| IOGND to GND | −0.3 V to +0.3 V |
| **Digital Input Voltages** |  |
| CNV and HIVIO/L̅O̅V̅I̅O̅ to GND | −0.3 V to (V_{DD} + 0.3 V) |
| All Other Inputs to GND | −0.3 V to (V_{IO} + 0.3 V) |
| **Digital Output Voltages** | −0.3 V to (V_{IO} + 0.3 V) |
| **Transient Latchup Currents[^2]** |  |
| IN0+ to IN7+ and IN0− to IN7− |  |
| V_{CC} − V_{EE} ≤ 44 V | ±100 mA |
| V_{CC} − V_{EE} > 44 V | ±10 mA |
| All other inputs and outputs | ±100 mA |
| **Temperature** |  |
| Storage Range | −65°C to +150°C |
| Operating Junction Range | −40°C to +105°C[^3] |
| Maximum Reflow (Package) | 260°C |

- **Note 1:** The absolute maximum ratings of V_{IO} depend on the selected state of the HIVIO/L̅O̅V̅I̅O̅ pin.
- **Note 2:** Adding an external resistor in series with each of the INx+ and INx− pins is recommended in applications where V_{CC} − V_{EE} > 44 V to limit latchup current to these levels during fault conditions. See the section Analog Input Overdrive Tolerance for further information.
- **Note 3:** The maximum junction temperature for continuous operation with nonderated device lifetime is 105°C. See the Junction Temperature section for more details.

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

### JUNCTION TEMPERATURE
<!-- page: 18 -->

The maximum junction temperature for continuous operation with nonderated device lifetime is 105°C. Operation at junction temperatures up to 125°C is also supported, with device specifications that are guaranteed from −40°C to +125°C. To avoid a reduction in operating lifetime due to operating at a temperature greater than105°C, the device must operate at a temperature less than 105°C for a compensating time period ( t_{COMP} ) determined by the following equation: 

t_{COMP} = (AF_{T} > 105 -1)/(1 - AF_{T} < 105)   (1)

where AF_{T} > 105 and AF_{T} < 105 are acceleration factors that are a function of the junction operating temperature.

For example, if the device operates at 115°C for 1 hour, the expected device lifetime is maintained if the device operates at 95°C for a compensating time period of 3.2 hours.

### THERMAL RESISTANCE
<!-- page: 18 -->

Thermal performance is directly linked to printed circuit board (PCB) design and operating environment. Careful attention to PCB thermal design is required. θ_{JA} is the natural convection junction to ambient thermal resistance measured in a one cubic foot sealed enclosure. θ_{JCT} is the junction to case top thermal resistance. θ_{JCB} is the junction to case bottom thermal resistance.

θ_{JA} is the natural convection junction to ambient thermal resistance measured in a one cubic foot sealed enclosure. θ_{JCT} is the junction to case top thermal resistance. θ_{JCB} is the junction to case bottom thermal resistance.

### Table 7. Thermal Resistance
<!-- page: 18 -->

**Table 7. Thermal Resistance** ([table-06-p18-data.csv](ad4858/tables/table-06-p18-data.csv), p. 18)

| Package Type | θ_{JA} | θ_{JCT} | θ_{JCB} | Unit |
|---|---|---|---|---|
| 05-08-7086 | 26.4 | 13.0 | 4.9 | °C/W |

### ELECTROSTATIC DISCHARGE (ESD) RATINGS
<!-- page: 18 -->

The following ESD information is provided for handling of ESD-sensitive devices in an ESD protected area only.

Human body model (HBM) per ANSI/ESDA/JEDEC JS-001. 

Field induced charged device model (FICDM) per ANSI/ESDA/JEDEC JS-002.

### ESD Ratings for AD4858
<!-- page: 18 -->

**Table 8. AD4858, 64-Ball BGA (ESD Ratings)** ([table-07-p18-data.csv](ad4858/tables/table-07-p18-data.csv), p. 18)

| ESD Model | Withstand Threshold (V) | Class |
|---|---|---|
| HBM | ±4000 | 3A |
| FICDM | ±750 | C4 |

### ESD CAUTION
<!-- pages: 18-19 -->

ESD (electrostatic discharge) sensitive device . Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

### PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
<!-- pages: 19-22 -->

![Figure 8. Pin Configuration](ad4858/figures/ad4858-f112.png)

*Figure 8. Pin Configuration*

AD4858 TOP VIEW (Not to Scale)


**Figure 8. Pin Configuration, Pin Matrix** ([pin-matrix-1.csv](ad4858/tables/pin-matrix-1.csv), p. 19)

| Row | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|---|---|---|---|---|---|---|---|---|
| A | IN2+ | IN1− | IN1+ | IN0− | IN0+ | GND | PD | CNV |
| B | IN2− | V_{CC} | GND | GND | GND | GND | BUSY | SCKI+/SDO0 |
| C | IN3+ | GND | REF2500 | REFIO | REFBUF | LVDS/C̅M̅O̅S̅ | SDO1 | SCKI−/SDO2 |
| D | IN3− | GND | GND | GND | GND | V_{IO} | SDO3 | SCKO+/SCKI |
| E | IN4+ | GND | HIVIO/L̅O̅V̅I̅O̅ | GND | GND | IOGND | SDO4 | SCKO−/SCKO |
| F | IN4− | GND | V_{DD} | V_{DDH} | V_{DDL} | CSDO | SDO6 | SDO+/SDO5 |
| G | IN5+ | V_{EE} | GND | GND | GND | GND | CSCK | SDO−/SDO7 |
| H | IN5− | IN6+ | IN6− | IN7+ | IN7− | GND | CSDIO | C̅S̅ |



**Table 9. Universal Pin Function Descriptions** ([table-08-p19-pin.csv](ad4858/tables/table-08-p19-pin.csv), p. 19)

| PIN NO. | MNEMONIC | TYPE[^1] | DESCRIPTION |
|---|---|---|---|
| A5 and A4, A3 and A2, A1 and B1, C1 and D1, E1 and F1, G1 and H1, H2 and H3, H4 and H5 | IN0+ and IN0− to IN7+ and IN7− | AI | Channel 0 to Channel 7 Positive and Negative Analog Inputs. The converter simultaneously samples and digitizes (V_{INx+} − V_{INx−}) for all channels. Wide input common-mode range and high common-mode rejection allow the inputs to accept arbitrary signal swings. Full-scale differential input range is determined by the SoftSpan configuration of each channel. |
| A6, B3 to B6, C2, D2, D3, D4, D5, E2, E4, E5, F2, G3 to G6, H6 | GND | P | Power Supply Ground. Solder all GND pins to a solid ground plane. |
| A7 | PD | DI | Power Down Input. Bring the PD pin high to power down the device. If the PD pin is brought high while the BUSY pin is high, power down begins once the BUSY pin goes low. Bringing the PD pin high twice without an intervening conversion initiates a global device reset, equivalent to a power-on-reset event. Logic levels are determined by the V_{IO} supply. |
| A8 | CNV | DI | Convert Input. A rising edge on the CNV pin initiates a new conversion. This signal must have low jitter to achieve specified device performance levels. The CNV high and low threshold voltages are 0.8 V and 0.4 V, respectively. |
| B2 | V_{CC} | P | Analog Input Buffers Positive Power Supply. Connect the V_{CC} pin to an external supply between 7.25 V and 48 V with respect to the GND pins and between 10 V and 48 V with respect to the V_{EE} pin. The V_{CC} pin is internally bypassed to the GND pins with a 0.1 µF ceramic capacitor. |
| B7 | BUSY | DO | Busy Output. The BUSY pin goes high at the start of each conversion (or oversampling window) and returns low once the conversion (or oversampling window) is complete. The BUSY pin also goes high during the start of power-on-reset and goes low once power-on-reset completes. Logic levels are determined by the V_{IO} supply. |
| C3 | REF2500 | AO | 2.5 V Scaled Reference Output. The REF2500 pin outputs a precision scaled version of the REFIO pin voltage, nominally V_{REFIO} × (2.500/4.096). If connecting REF2500 externally, see the DAS Reference section for recommended use cases and precautions. |
| C4 | REFIO | AI or AO | Band-gap Reference Output and Reference Buffer Input. An internal band-gap reference nominally outputs 4.096 V on the REFIO pin. The REFIO pin is internally bypassed to the GND pins with a 10 nF ceramic capacitor to filter the band-gap output noise. If the REFIO pin is overdriven with an external 4.096 V reference, disable the internal reference through the Device Control Register. If connecting the REFIO pin externally, see the DAS Reference section for recommended uses cases and precautions. |
| C5 | REFBUF | AI or AO | Reference Buffer Output. An internal unity-gain reference buffer creates the converter main reference voltage, V_{REFBUF} = V_{REFIO} on the REFBUF pin, nominally 4.096 V when using the internal band-gap reference. If the REFBUF pin is overdriven with an external 4.096 V reference, disable the internal reference buffer and band-gap reference through the Device Control Register and bypass the REFBUF pin to GND (pin B4) close to the REFBUF pin with an external 47 µF ceramic capacitor. If connecting the REFBUF pin externally, see the DAS Reference section for recommended uses cases and precautions. |
| C6 | LVDS/C̅M̅O̅S̅ | DI | Conversion Data Bus Mode Select. Tie the LVDS/C̅M̅O̅S̅ pin to the V_{IO} pin to select LVDS conversion data output mode or to the GND pins to select CMOS conversion data output mode. The state of the LVDS/C̅M̅O̅S̅ pin does not affect the behavior of the SPI register configuration bus. Logic levels are determined by the V_{IO} supply. |
| D6[^2] | V_{IO} | P | Digital Input and Output Power Supply. Connect the V_{IO} pin to an external supply between 0.9 V and 5.25 V with respect to the GND pins. The HIVIO/L̅O̅V̅I̅O̅ pin must be tied appropriately based on application V_{IO} level. Tie the HIVIO/L̅O̅V̅I̅O̅ pin to the V_{DD} pin for applications where 1.71 V ≤ V_{IO} ≤ 5.25 V or tie the HIVIO/L̅O̅V̅I̅O̅ pin to the GND pins for applications where 0.9 V ≤ V_{IO} ≤ 1.89 V. Either tie option can be used when 1.71 V ≤ V_{IO} ≤ 1.89 V. The V_{IO} pin is internally bypassed to the IOGND pin with a 1 µF ceramic capacitor. |
| E3[^2] | HIVIO/L̅O̅V̅I̅O̅ | DI | V_{IO} Voltage Mode Select. Tie the HIVIO/L̅O̅V̅I̅O̅ pin to the V_{DD} pin for applications where 1.71 V ≤ V_{IO} ≤ 5.25 V or to the GND pins where 0.9 V ≤ V_{IO} ≤ 1.89 V. Either tie option may be used when 1.71 V ≤ V_{IO} ≤ 1.89 V. Logic levels are determined by the V_{DD} supply. |
| E6 | IOGND | P | Digital Input and Output Power Supply Ground. Solder the IOGND pin to the same ground plane as the GND pins. |
| F3 | V_{DD} | P | 5 V Power Supply. Connect the V_{DD} pin to an external 5 V supply. The V_{DD} pin is internally bypassed to the GND pins with a 1 µF ceramic capacitor. |
| F4 | V_{DDH} | P | 1.8 V LDO Regulator Power Supply. To supply the V_{DDL} pin using the internal 1.8 V LDO regulator, tie the V_{DDH} pin to the V_{DD} pin or to another external power supply between 2.2 V and 5.25 V. To disable the internal LDO regulator, tie the V_{DDH} pin to the GND pins as shown in Figure 61. The V_{DDH} pin is internally bypassed to the GND pins with a 1 µF ceramic capacitor. |
| F5 | V_{DDL} | P | 1.8 V Power Supply. To supply the V_{DDL} pin using the internal 1.8 V LDO regulator, tie the V_{DDH} pin to the V_{DD} pin or to another external power supply between 2.2 V and 5.25 V. Do not externally connect the V_{DDL} pin in this case. To externally supply the V_{DDL} pin, disable the internal LDO regulator by tying the V_{DDH} pin to the GND pins and connect the V_{DDL} pin to an external 1.8 V supply as shown in Figure 61. The V_{DDL} pin is internally bypassed to the GND pins with a 1 µF ceramic capacitor. |
| F6 | CSDO | DO | SPI Register Configuration Bus Data Output. During 3-wire SPI register configuration bus operation, the CSDO pin remains high-Z. During 4-wire bus operation, the CSDO pin outputs serial data during read transactions. Logic levels are determined by the V_{IO} supply. |
| G2 | V_{EE} | P | Analog Input Buffers Negative Power Supply. Connect the V_{EE} pin to an external supply between 0 V and −40.75 V with respect to the GND pins and between −10 V and −48 V with respect to the V_{CC} pin. The V_{EE} pin is internally bypassed to the GND pins with a 0.1 µF ceramic capacitor. |
| G7 | CSCK | DI | SPI Register Configuration Bus Clock Input. Drive the CSCK pin with the SPI register configuration bus clock. The CSCK pin is allowed to idle either high or low. Logic levels are determined by the V_{IO} supply. |
| H7 | CSDIO | DI and DO | SPI Register Configuration Bus Data Input and Output. During both 3- and 4-wire SPI register configuration bus operation, the CSDIO pin accepts serial input data. During 3-wire bus operation, the CSDIO pin also outputs serial data during read transactions. Logic levels are determined by the V_{IO} supply. |
| H8 | C̅S̅ | DI | Chip Select Input. The SPI register configuration and conversion data buses are enabled when the C̅S̅ pin is low and disabled and high-Z when the C̅S̅ pin is high. Logic levels are determined by the V_{IO} supply. |

- **Note 1:** AI is analog input, AO is analog output, P is power, DI is digital input, and DO is digital output.
- **Note 2:** The maximum operating and absolute maximum ratings of the V_{IO} supply, and associated digital inputs and outputs, are defined by the HIVIO/L̅O̅V̅I̅O̅ pin state.


<!-- page: 21 -->

**Table 10. CMOS Conversion Data Bus Pin Function Descriptions** ([table-09-p21-pin.csv](ad4858/tables/table-09-p21-pin.csv), p. 21)

| PIN NO. | MNEMONIC | TYPE[^1]   | DESCRIPTION |
|---|---|---|---|
| B8, C7, C8, D7, E7, F7, F8, G8 | SDO0 to SDO7 | DO   | Channel 0 to Channel 7 CMOS Conversion Data Outputs. Conversion results and optional channel status information are output on these pins synchronized to the SCKI pin. The SDO0 pin may also be configured through the SPI Configuration D Register to output SPI register configuration bus serial data during 4-wire read operations. Logic levels are determined by the V_{IO} supply. |
| D8 | SCKI | DI   | CMOS Conversion Data Clock Input. Drive the SCKI pin with the CMOS conversion data bus clock. The SCKI pin is allowed to idle either high or low. Logic levels are determined by the V_{IO} supply. |
| E8 | SCKO | DO   | CMOS Conversion Data Clock Output. The SCKO pin outputs a copy of the SCKI pin skew-matched to the serial output data on the SDO0 to SDO7 pins. If clock echoing is disabled through the Device Control Register, the SCKO pin is high-Z. Logic levels are determined by the V_{IO} supply. |

- **Note 1:** AI is analog input, AO is analog output, P is power, DI is digital input, and DO is digital output.

<!-- page: 21 -->

**Table 11. LVDS Conversion Data Bus Pin Function Descriptions** ([table-10-p21-pin.csv](ad4858/tables/table-10-p21-pin.csv), p. 21)

| PIN NO. | MNEMONIC | TYPE[^1] | DESCRIPTION |
|---|---|---|---|
| B8 and C8 | SCKI+ and SCKI− | DI | LVDS Conversion Data Clock Input. Differentially drive the SCKI+ and SCKI− pins with the LVDS conversion data bus clock. Idle the SCKI+ and SCKI− pins low (including when transitioning C̅S̅). By default, the SCKI+ and SCKI− pins are internally terminated with a 100 Ω differential resistor when the C̅S̅ pin is low. This termination can be disabled through the Device Control Register. |
| C7, D7, E7, F7 | SDO1, SDO3, SDO4, SDO6 | DO | CMOS Conversion Data Outputs. In LVDS conversion data output mode, the SDO1, SDO3, SDO4, and SDO6 pins are high-Z. |
| D8 and E8 | SCKO+ and SCKO− | DO | LVDS Conversion Data Clock Output. The SCKO+ and SCKO− pins output a copy of the SCKI+ and SCKI− pins, skew-matched with the serial output data on the SDO+ and SDO− pins. The SCKO+ and SCKO− output pair must be differentially terminated with a 100 Ω resistor at the receiver field programmable gate array (FPGA). If clock echoing is disabled through the Device Control Register, these pins are high-Z. |
| F8 and G8 | SDO+ and SDO− | DO | LVDS Conversion Data Output. Conversion results and optional channel status information are output on these pins synchronized to the SCKI+ and SCKI− pins. The SDO+ and SDO− output pair must be differentially terminated with a 100 Ω resistor at the receiver (FPGA). |

- **Note 1:** AI is analog input, AO is analog output, P is power, DI is digital input, and DO is digital output.

### TYPICAL PERFORMANCE CHARACTERISTICS
<!-- pages: 22-29 -->

V_{EE} = −24 V, V_{CC} = +24 V, V_{DD} = +5 V, V_{DDH} = +2.5 V, 1.8 V LDO regulator enabled, V_{IO} = +2.5 V, f_{S} = 1 MSPS, internal reference and reference buffer enabled, fully-differential input signal drive in SoftSpan 15 and SoftSpan 13, true bipolar or unipolar signal drive in other bipolar or unipolar SoftSpan ranges, and T_{A} = 25°C, unless otherwise noted.

![Figure 9. INL Error vs. Differential Input Voltage, SoftSpan 15 to SoftSpan 14](ad4858/figures/ad4858-f010.png)

*Figure 9. INL Error vs. Differential Input Voltage, SoftSpan 15 to SoftSpan 14*

Digitized data: [inl-error-vs-differential-input-voltage-softspan-15-to-softspan-14.csv](ad4858/curves/inl-error-vs-differential-input-voltage-softspan-15-to-softspan-14.csv) (x: V; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 10. INL Error vs. Differential Input Voltage, SoftSpan 9 to SoftSpan 6](ad4858/figures/ad4858-f011.png)

*Figure 10. INL Error vs. Differential Input Voltage, SoftSpan 9 to SoftSpan 6*

Digitized data: [inl-error-vs-differential-input-voltage-softspan-9-to-softspan-6.csv](ad4858/curves/inl-error-vs-differential-input-voltage-softspan-9-to-softspan-6.csv) (x: V; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 11. INL Error vs. Differential Input Voltage, SoftSpan 1 to SoftSpan 0](ad4858/figures/ad4858-f012.png)

*Figure 11. INL Error vs. Differential Input Voltage, SoftSpan 1 to SoftSpan 0*

Digitized data: [inl-error-vs-differential-input-voltage-softspan-1-to-softspan-0.csv](ad4858/curves/inl-error-vs-differential-input-voltage-softspan-1-to-softspan-0.csv) (x: V; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 12. INL Error vs. Differential Input Voltage, SoftSpan 13 to SoftSpan 10](ad4858/figures/ad4858-f013.png)

*Figure 12. INL Error vs. Differential Input Voltage, SoftSpan 13 to SoftSpan 10*

Digitized data: [inl-error-vs-differential-input-voltage-softspan-13-to-softspan-10.csv](ad4858/curves/inl-error-vs-differential-input-voltage-softspan-13-to-softspan-10.csv) (x: V; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 13. INL Error vs. Differential Input Voltage, SoftSpan 5 to SoftSpan 2](ad4858/figures/ad4858-f014.png)

*Figure 13. INL Error vs. Differential Input Voltage, SoftSpan 5 to SoftSpan 2*

Digitized data: [inl-error-vs-differential-input-voltage-softspan-5-to-softspan-2.csv](ad4858/curves/inl-error-vs-differential-input-voltage-softspan-5-to-softspan-2.csv) (x: V; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 14. DNL Error vs. Differential Input Voltage](ad4858/figures/ad4858-f015.png)

*Figure 14. DNL Error vs. Differential Input Voltage*

Digitized data: [dnl-error-vs-differential-input-voltage.csv](ad4858/curves/dnl-error-vs-differential-input-voltage.csv) (x: V; y: LSB 20) — values read off the printed plot by the digitizer, not published data.

![Figure 15. INL Error vs. Input Common Mode and Input Differential Voltage](ad4858/figures/ad4858-f016.png)

*Figure 15. INL Error vs. Input Common Mode and Input Differential Voltage*

![Figure 16. DC Code Histogram, Near Zero Scale](ad4858/figures/ad4858-f017.png)

*Figure 16. DC Code Histogram, Near Zero Scale*

![Figure 17. Input Step Response, Large Signal Settling](ad4858/figures/ad4858-f018.png)

*Figure 17. Input Step Response, Large Signal Settling*

Digitized data: [input-step-response-large-signal-settling.csv](ad4858/curves/input-step-response-large-signal-settling.csv) (x: ns; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 18. Input-Referred Noise vs. Differential Input Voltage](ad4858/figures/ad4858-f019.png)

*Figure 18. Input-Referred Noise vs. Differential Input Voltage*

Digitized data: [input-referred-noise-vs-differential-input-voltage.csv](ad4858/curves/input-referred-noise-vs-differential-input-voltage.csv) (x: V; y: µV rms) — values read off the printed plot by the digitizer, not published data.

![Figure 19. DC Code Histogram, Near Full Scale](ad4858/figures/ad4858-f020.png)

*Figure 19. DC Code Histogram, Near Full Scale*

![Figure 20. Input Step Response, Fine Settling](ad4858/figures/ad4858-f021.png)

*Figure 20. Input Step Response, Fine Settling*

Digitized data: [input-step-response-fine-settling.csv](ad4858/curves/input-step-response-fine-settling.csv) (x: ns; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 21. FFT, 1 MSPS, f_{IN} = 1 kHz, ±40 V Range](ad4858/figures/ad4858-f022.png)

*Figure 21. FFT, 1 MSPS, f_{IN} = 1 kHz, ±40 V Range*

![Figure 22. FFT, 1 MSPS, f_{IN} = 1 kHz, ±5 V Range](ad4858/figures/ad4858-f023.png)

*Figure 22. FFT, 1 MSPS, f_{IN} = 1 kHz, ±5 V Range*

![Figure 23. SNR, SINAD, and THD vs. Input Level](ad4858/figures/ad4858-f024.png)

*Figure 23. SNR, SINAD, and THD vs. Input Level*

Digitized data: [snr-sinad-and-thd-vs-input-level.csv](ad4858/curves/snr-sinad-and-thd-vs-input-level.csv) (x: dBFS; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 24. FFT, 1 MSPS, f_{IN} = 1 kHz, ±10 V Range](ad4858/figures/ad4858-f025.png)

*Figure 24. FFT, 1 MSPS, f_{IN} = 1 kHz, ±10 V Range*

![Figure 25. FFT, 1 MSPS, f_{INx+} = 991 Hz, f INx= 1.6 kHz, ±40 V Range](ad4858/figures/ad4858-f026.png)

*Figure 25. FFT, 1 MSPS, f_{INx+} = 991 Hz, f INx= 1.6 kHz, ±40 V Range*

![Figure 26. SNR and SINAD vs. Input Frequency](ad4858/figures/ad4858-f027.png)

*Figure 26. SNR and SINAD vs. Input Frequency*

Digitized data: [snr-and-sinad-vs-input-frequency.csv](ad4858/curves/snr-and-sinad-vs-input-frequency.csv) (x: Hz; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 27. THD, Harmonics vs. Input Frequency](ad4858/figures/ad4858-f028.png)

*Figure 27. THD, Harmonics vs. Input Frequency*

Digitized data: [thd-harmonics-vs-input-frequency.csv](ad4858/curves/thd-harmonics-vs-input-frequency.csv) (x: Hz; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 28. Crosstalk vs. Interferer Frequency](ad4858/figures/ad4858-f029.png)

*Figure 28. Crosstalk vs. Interferer Frequency*

Digitized data: [crosstalk-vs-interferer-frequency.csv](ad4858/curves/crosstalk-vs-interferer-frequency.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 29. Power Supply Rejection Ratio (PSRR) vs. Frequency](ad4858/figures/ad4858-f030.png)

*Figure 29. Power Supply Rejection Ratio (PSRR) vs. Frequency*

Digitized data: [power-supply-rejection-ratio-psrr-vs-frequency.csv](ad4858/curves/power-supply-rejection-ratio-psrr-vs-frequency.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 30. CMRR vs. Input Frequency](ad4858/figures/ad4858-f031.png)

*Figure 30. CMRR vs. Input Frequency*

Digitized data: [cmrr-vs-input-frequency.csv](ad4858/curves/cmrr-vs-input-frequency.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 31. Zero-Scale Error vs. Common-Mode Input Voltage](ad4858/figures/ad4858-f032.png)

*Figure 31. Zero-Scale Error vs. Common-Mode Input Voltage*

Digitized data: [zero-scale-error-vs-common-mode-input-voltage.csv](ad4858/curves/zero-scale-error-vs-common-mode-input-voltage.csv) (x: V; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 32. PSRR vs. Frequency, Internal and External Reference](ad4858/figures/ad4858-f033.png)

*Figure 32. PSRR vs. Frequency, Internal and External Reference*

Digitized data: [psrr-vs-frequency-internal-and-external-reference.csv](ad4858/curves/psrr-vs-frequency-internal-and-external-reference.csv) (x: Hz; y: dB) — values read off the printed plot by the digitizer, not published data.

![Figure 33. Supply Current vs. Sample Rate](ad4858/figures/ad4858-f034.png)

*Figure 33. Supply Current vs. Sample Rate*

Digitized data: [supply-current-vs-sample-rate.csv](ad4858/curves/supply-current-vs-sample-rate.csv) — values read off the printed plot by the digitizer, not published data.

![Figure 34. Dynamic Range vs. Oversampling Ratio](ad4858/figures/ad4858-f035.png)

*Figure 34. Dynamic Range vs. Oversampling Ratio*

Digitized data: [dynamic-range-vs-oversampling-ratio.csv](ad4858/curves/dynamic-range-vs-oversampling-ratio.csv) (x: ratio; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 35. Change in Internal Reference Voltage vs. Burn-In Time](ad4858/figures/ad4858-f036.png)

*Figure 35. Change in Internal Reference Voltage vs. Burn-In Time*

Digitized data: [change-in-internal-reference-voltage-vs-burn-in-time.csv](ad4858/curves/change-in-internal-reference-voltage-vs-burn-in-time.csv) (x: h; y: mV) — values read off the printed plot by the digitizer, not published data.

![Figure 36. Burst Conversion Response, f_{S} = 1 MSPS](ad4858/figures/ad4858-f037.png)

*Figure 36. Burst Conversion Response, f_{S} = 1 MSPS*

Digitized data: [burst-conversion-response-f-s-1-msps.csv](ad4858/curves/burst-conversion-response-f-s-1-msps.csv) (x: µs; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 37. Low Frequency Noise over 10 seconds](ad4858/figures/ad4858-f038.png)

*Figure 37. Low Frequency Noise over 10 seconds*

![Figure 38. Change in Zero-Scale Error vs. Burn-In Time](ad4858/figures/ad4858-f039.png)

*Figure 38. Change in Zero-Scale Error vs. Burn-In Time*

Digitized data: [change-in-zero-scale-error-vs-burn-in-time.csv](ad4858/curves/change-in-zero-scale-error-vs-burn-in-time.csv) (x: h; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 39. Zero-Scale Error vs. Temperature](ad4858/figures/ad4858-f040.png)

*Figure 39. Zero-Scale Error vs. Temperature*

Digitized data: [zero-scale-error-vs-temperature.csv](ad4858/curves/zero-scale-error-vs-temperature.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 40. Internal Reference Output vs. Temperature](ad4858/figures/ad4858-f041.png)

*Figure 40. Internal Reference Output vs. Temperature*

Digitized data: [internal-reference-output-vs-temperature.csv](ad4858/curves/internal-reference-output-vs-temperature.csv) (x: °C; y: V) — values read off the printed plot by the digitizer, not published data.

![Figure 41. Analog Input Leakage Current vs. Temperature](ad4858/figures/ad4858-f042.png)

*Figure 41. Analog Input Leakage Current vs. Temperature*

Digitized data: [analog-input-leakage-current-vs-temperature.csv](ad4858/curves/analog-input-leakage-current-vs-temperature.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

![Figure 42. Positive Full-Scale Error vs. Temperature](ad4858/figures/ad4858-f043.png)

*Figure 42. Positive Full-Scale Error vs. Temperature*

Digitized data: [positive-full-scale-error-vs-temperature.csv](ad4858/curves/positive-full-scale-error-vs-temperature.csv) (x: °C; y: %) — values read off the printed plot by the digitizer, not published data.

![Figure 43. Reference Buffer Offset Voltage vs. Temperature](ad4858/figures/ad4858-f044.png)

*Figure 43. Reference Buffer Offset Voltage vs. Temperature*

Digitized data: [reference-buffer-offset-voltage-vs-temperature.csv](ad4858/curves/reference-buffer-offset-voltage-vs-temperature.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 44. INL/DNL Error vs. Temperature](ad4858/figures/ad4858-f045.png)

*Figure 44. INL/DNL Error vs. Temperature*

Digitized data: [inl-dnl-error-vs-temperature.csv](ad4858/curves/inl-dnl-error-vs-temperature.csv) (x: °C; y: µV) — values read off the printed plot by the digitizer, not published data.

![Figure 45. SNR and SINAD vs. Temperature](ad4858/figures/ad4858-f046.png)

*Figure 45. SNR and SINAD vs. Temperature*

Digitized data: [snr-and-sinad-vs-temperature.csv](ad4858/curves/snr-and-sinad-vs-temperature.csv) (x: °C; y: dBFS) — values read off the printed plot by the digitizer, not published data.

![Figure 46. Supply Current vs. Temperature](ad4858/figures/ad4858-f047.png)

*Figure 46. Supply Current vs. Temperature*

Digitized data: [supply-current-vs-temperature.csv](ad4858/curves/supply-current-vs-temperature.csv) (x: °C; y: mA) — values read off the printed plot by the digitizer, not published data.

![Figure 47. THD, Harmonics vs. Temperature](ad4858/figures/ad4858-f048.png)

*Figure 47. THD, Harmonics vs. Temperature*

Digitized data: [thd-harmonics-vs-temperature.csv](ad4858/curves/thd-harmonics-vs-temperature.csv) (x: °C; y: dBc) — values read off the printed plot by the digitizer, not published data.

![Figure 48. Power-Down Current vs. Temperature](ad4858/figures/ad4858-f049.png)

*Figure 48. Power-Down Current vs. Temperature*

Digitized data: [power-down-current-vs-temperature.csv](ad4858/curves/power-down-current-vs-temperature.csv) (x: °C; y: A) — values read off the printed plot by the digitizer, not published data.

### TERMINOLOGY
<!-- pages: 29-30 -->

### Integral Nonlinearity (INL) Error
<!-- page: 29 -->

INL is the deviation of each individual code from a line drawn through the two endpoints of the ADC transfer function. The two endpoints of the transfer function are ½ LSB before the first code transition and 1½ LSB beyond the last code transition. The deviation is measured from the middle of each code to the true straight line.

### Differential Nonlinearity (DNL) Error
<!-- page: 29 -->

In an ideal ADC, code transitions are 1 LSB apart. DNL is the maximum deviation from this ideal value. DNL is often specified in terms of resolution for which no missing codes are guaranteed.

### Zero-Scale Error
<!-- page: 29 -->

For both bipolar and unipolar SoftSpan ranges, zero-scale error is the difference between the ideal zero-scale input voltage of 0 V and the actual input voltage which produces the zero-scale output code of 0 LSB.

### Full-Scale Error
<!-- page: 29 -->

For bipolar SoftSpan ranges, full-scale error is the worst-case deviation of the first and last code transitions from ideal. It includes the effect of zero-scale error and any contributions from the reference buffer.

For unipolar SoftSpan ranges, full-scale error is the worst-case deviation of the last code transition from ideal. It includes the effect of zero-scale error and any contributions from the reference buffer.

### Effective Number of Bits (ENOB)
<!-- page: 29 -->

ENOB is a measurement of the resolution with a sine wave input. It is related to SINAD by the following formula:

ENOB = (SINAD_{dB} − 1.76)/6.02

ENOB is expressed in bits.

### Dynamic Range
<!-- page: 29 -->

Dynamic range is the ratio of the RMS amplitude of a full-scale sine wave to the total RMS noise and is expressed in decibels (dB). It is measured with a -60 dBFS input signal to include all noise sources and DNL artifacts.

### Signal-to-Noise Ratio (SNR)
<!-- page: 29 -->

SNR is the ratio of the RMS amplitude of a full-scale sine wave to the RMS sum of all other spectral components below the Nyquist frequency, excluding the first five harmonics and DC. The value for SNR is expressed in decibels (dB).

### Signal-to-Noise-and-Distortion (SINAD) Ratio
<!-- page: 29 -->

SINAD is the ratio of the RMS amplitude of a full-scale sine wave to the RMS sum of all other spectral components below the Nyquist frequency, including harmonics but excluding DC. The value for SINAD is expressed in decibels (dB).

### Total Harmonic Distortion (THD)
<!-- page: 29 -->

THD is the ratio of the RMS sum of the first five harmonic components to the RMS amplitude of the fundamental input signal and is expressed in decibels (dB).

### Spurious-Free Dynamic Range (SFDR)
<!-- page: 29 -->

SFDR is the difference in decibels (dB) between the RMS amplitude of a full-scale input signal and the peak spurious signal.

### Channel-to-Channel Crosstalk
<!-- page: 29 -->

Channel-to-channel crosstalk is measured by applying a sine wave at frequency (f_{INJ} ) on one interferer injection channel and a second sine wave at a different frequency (f_{RCV} ) on all receiver channels. Crosstalk is the ratio of the RMS sum of the spectral tones at f_{INJ} and up to 5th-order intermodulation products on the receiver and injector channels. Channel-to-channel Crosstalk is expressed in decibels (dB). All channels convertat f_{S} = 1 MSPS with the internal reference and reference buffer enabled during the measurement.

### Aperture Delay
<!-- page: 29 -->

Aperture delay is a measure of acquisition performance. It is the time between the rising edge of the CNV input and when the input signals are held for a conversion.

### Transient Response
<!-- page: 29 -->

Transient response is the time required for the ADC to acquire a full-scale input step to 50 ppm settling accuracy.

### Common-Mode Rejection Ratio (CMRR)
<!-- page: 29 -->

CMRR is the ratio of the RMS amplitude of a sine wave of frequency (f) applied to the analog input common-mode voltage to the RMS amplitude of the ADC output data at frequency (f). The value for CMRR is expressed in decibels (dB).

### Power Supply Rejection Ratio (PSRR)
<!-- page: 29 -->

PSRR is the ratio of the RMS amplitude of a sine wave of frequency (f) applied to the power supply voltage to the RMS amplitude of the ADC output data at frequency (f). The value for PSRR is expressed in decibels (dB).

### THEORY OF OPERATION
<!-- pages: 30-36 -->

### OVERVIEW
<!-- page: 30 -->

The AD4858 is a fully buffered, 8-channel simultaneous sampling, 20-bit 1 MSPS data acquisition system with differential, wide common-mode range inputs. Its functional architecture is shown in Figure 1. Operating from a 5 V low voltage supply, flexible input buffer supplies, and using the precision low drift internal reference and reference buffer, the AD4858 allows the SoftSpan range of each channel to be independently configured to match the native application signal swing, minimizing additional external signal conditioning. To further maximize single-conversion dynamic range, the AD4858 incorporates SHDR technology. When enabled, the input signal path gain of a channel is automatically optimized on a sample-by-sample basis, minimizing converter noise on each sample without impacting linearity.

The 11 MHz bandwidth, picoamp-input analog buffers, wide input common-mode range, and 120 dB CMRR of the AD4858 allow the DAS to directly digitize input signals with arbitrary swings on INx+ and INx-. This input signal flexibility, combined with ±160 µV INL, no missing codes at 20 bits, 97.2 dB SNR, and 111.4 dB dynamic range makes the AD4858 an ideal choice for applications requiring high accuracy, throughput, and precision in a compact solution footprint.

The absolute input range of the AD4858 analog-input buffers spans (V_{EE} + 3.2 V) to (V_{CC} - 3.2V). The buffer supplies, V_{CC} and V_{EE} , are flexible, allowing them to be chosen to match the native application signal swing requirements and eliminating the need for additional signal conditioning. The supplies may be biased asymmetrically around ground and include the ability for the V_{EE} pin to be tied directly to GND.

Digital features of the AD4858 include optional 24-bit oversampling, which offers further SNR and dynamic range improvements, and optional per channel offset, gain, and phase adjustment that allow for system-level errors upstream to the DAS to be corrected.

The AD4858 features a dedicated SPI register configuration bus (0.9 V to 5.25 V), and pin selectable serial LVDS and CMOS conversion data output buses. Between 1 line and 8 lines of data output (SDO0 to SDO7) may be employed in CMOS mode to optimize bus width and throughput.

The AD4858 typically dissipates 45 mW per channel when converting 8 channels simultaneously at 1 MSPS. Use the optional nap and power down modes to further reduce power consumption during inactive periods.

### CONVERTER OPERATION
<!-- page: 30 -->

The AD4858 operates in two phases. During the acquisition phase, the sampling capacitors in the sample-and-hold circuit of each channel connect to their respective analog-input buffers (see Figure 53) and track the differential input voltage (V_{INx+} - V_{INx}). A rising edge on the CNV pin transitions all of the sample-and-hold circuits from track mode to hold mode, simultaneously sampling the input signals on all channels and initiating a conversion. During the conversion phase, the sampling capacitors of each channel are connected to a 20-bit charge redistribution capacitor digital-to-analog converter (CDAC). The CDAC is sequenced through a successive approximation algorithm, effectively comparing the sampled input voltage with binary-weighted fractions of the SoftSpan full-scale range of the channel (for example, V_{FSR} /2, V_{FSR} /4 … V_{FSR} /2^{20} ) using a differential comparator. At the end of this process, the CDAC outputs approximate the sampled analog inputs of each channel. Once all channels have been converted in this manner, the ADC control logic prepares the 20-bit digital output codes from each channel for serial transfer.

### TRANSFER FUNCTION
<!-- page: 30 -->

The AD4858 digitizes the full-scale voltage range of each channel into 2^{20} discrete levels. In conjunction with the ADC main reference voltage, V_{REFBUF} , the SoftSpan configuration of each channel determines its differential input voltage range, LSB size, and the binary format of its conversion result, as shown in Table 12. Conversion results are output in twos complement binary format for all bipolar SoftSpan ranges, and in straight binary format for all unipolar SoftSpan ranges. The ideal bipolar input transfer function is shown in Figure 49, and the ideal unipolar input transfer function is shown in Figure 50.

![Figure 49. AD4858 Ideal Bipolar Input Transfer Function. N = 20 bits](ad4858/figures/ad4858-f050.png)

*Figure 49. AD4858 Ideal Bipolar Input Transfer Function. N = 20 bits*

![Figure 50. AD4858 Ideal Unipolar Input Transfer Function. N = 20 bits](ad4858/figures/ad4858-f051.png)

*Figure 50. AD4858 Ideal Unipolar Input Transfer Function. N = 20 bits*

**Table 12. SoftSpan Range Properties** ([table-11-p31-data.csv](ad4858/tables/table-11-p31-data.csv), p. 31)

| SoftSpan | Differential Input Range (V_{INx+} − V_{INx-}) | Negative Full Scale (V) | Zero Scale (V) | Positive Full Scale (V) | LSB (µV) |
|---|---|---|---|---|---|
| **Ideal Ranges (V_{REFBUF} = 4.096 V)** |  |  |  |  |  |
|  | Bipolar (Twos Complement Output Code) |  |  |  |  |
| 15 | ±10 × (V_{REFBUF}/1.024) | −40 | 0 | +40 | 76.294 |
| 13 | ±6.25 × (V_{REFBUF}/1.024) | −25 | 0 | +25 | 47.684 |
| 11 | ±5 × (V_{REFBUF}/1.024) | −20 | 0 | +20 | 38.147 |
| 9 | ±3.125 × (V_{REFBUF}/1.024) | −12.5 | 0 | +12.5 | 23.842 |
| 7 | ±2.5 × (V_{REFBUF}/1.024) | −10 | 0 | +10 | 19.073 |
| 5 | ±1.5625 × (V_{REFBUF}/1.024) | −6.25 | 0 | +6.25 | 11.921 |
| 3 | ±1.25 × (V_{REFBUF}/1.024) | −5 | 0 | +5 | 9.537 |
| 1 | ±0.625 × (V_{REFBUF}/1.024) | −2.5 | 0 | +2.5 | 4.768 |
|  | Unipolar (Straight Binary Output Code) |  |  |  |  |
| 14 | 0 to 10 × (V_{REFBUF}/1.024) |  | 0 | 40 | 38.147 |
| 12 | 0 to 6.25 × (V_{REFBUF}/1.024) |  | 0 | 25 | 23.842 |
| 10 | 0 to 5 × (V_{REFBUF}/1.024) |  | 0 | 20 | 19.073 |
| 8 | 0 to 3.125 × (V_{REFBUF}/1.024) |  | 0 | 12.5 | 11.921 |
| 6 | 0 to 2.5 × (V_{REFBUF}/1.024) |  | 0 | 10 | 9.537 |
| 4 | 0 to 1.5625 × (V_{REFBUF}/1.024) |  | 0 | 6.25 | 5.960 |
| 2 | 0 to 1.25 × (V_{REFBUF}/1.024) |  | 0 | 5 | 4.768 |
| 0 | 0 to 0.625 × (V_{REFBUF}/1.024) |  | 0 | 2.5 | 2.384 |

### SOFTSPAN
<!-- page: 30 -->

Each channel of the AD4858 may be independently configured in one of the 16 SoftSpan ranges, as shown in Table 12. Select the SoftSpan range of each channel based on the required differential analog input (V_{INx+} - V_{INx}) range to be digitized. All channels default to SoftSpan 15, corresponding to a nominal ±40 V bipolar input span. To configure a channel for a different range, write the 4-bit SoftSpan code to the corresponding register address shown in Table 13.

**Table 13. Per Channel SoftSpan Registers** ([table-12-p31-register.csv](ad4858/tables/table-12-p31-register.csv), p. 31)

| Register Name | Register Address |
|---|---|
| CH0_SOFTSPAN | 0x2A |
| CH1_SOFTSPAN | 0x3C |
| CH2_SOFTSPAN | 0x4E |
| CH3_SOFTSPAN | 0x60 |
| CH4_SOFTSPAN | 0x72 |
| CH5_SOFTSPAN | 0x84 |
| CH6_SOFTSPAN | 0x96 |
| CH7_SOFTSPAN | 0xA8 |

Regardless of the chosen SoftSpan range, the wide common-mode input range and high CMRR of the INx+ and INx- analog inputs allow them to swing with an arbitrary relationship to each other, provided each pin remains between (V_{EE} + 3.2 V) and (V_{CC} - 3.2 V).

### SEAMLESS HIGH DYNAMIC RANGE
<!-- page: 31 -->

SHDR is a proprietary technique that provides the lowest possible input-referred conversion noise on a sample-by-sample basis.

With SHDR disabled, the SoftSpan range of each channel automatically defines a fixed converter analog signal gain that is applied to every sample for that channel. The fixed gain must be low enough that the channel does not saturate at the maximum signal level of the chosen SoftSpan. The fixed gain results in a fixed input-referred noise level for all samples.

With SHDR enabled, the converter dynamically adjusts analog signal gain based on the differential voltage of each sample. For differential voltage magnitudes near the maximum of the chosen SoftSpan range, the gain employed is the same as the value used with SHDR disabled. However, for samples with lower magnitude, the converter automatically increases gain, resulting in lower inputreferred conversion noise for these samples and improved dynamic range.

All conversion results are reported in the selected SoftSpan range format, requiring no additional output data manipulation to employ this mode. A comparison of converter input-referred noise with SHDR on and off is shown in Figure 18. As shown in Table 1, enabling SHDR offers up to 15.6 dB improvement in single-conversion dynamic range.

Seamless high dynamic range is enabled on all channels by default. To disable SHDR on a channel, clear the corresponding control bit in the SEAMLESS\_HDR register.

### DIGITAL PROCESSING FEATURES
<!-- page: 32 -->

The AD4858 supports several digital data postprocessing features that can be applied to conversion results, including oversampling, and offset, gain, and phase correction. These features are configured via the AD4858 control registers described in the Register Summary section.

### Oversampling Mode
<!-- page: 32 -->

The AD4858 operates in nonoversampling mode by default. As shown in Figure 6 and Figure 7, in this mode the BUSY line transitions low-to-high at the start of each conversion, and the SDO0 to SDO7 lines (CMOS) or SDO lines (LVDS) are updated with the latest conversion results from each channel at the end of every conversion, just prior to the falling edge of the BUSY line.

With oversampling mode enabled, the AD4858 computes the digital average of multiple conversion results for each channel. In this mode, all channels share a single common oversampling ratio, and only the averaged result for each channel is available to be read from the AD4858. Oversampling is useful in applications requiring lower noise and higher dynamic range per output data-word, which the AD4858 supports with 24-bit output resolution and reduced average output data rates. Oversampling mode also supports optional Digital Phase Correction.

To use oversampling mode, select the oversampling ratio from Table 43 corresponding to the number of conversion results to be digitally averaged for each channel. Program the chosen 4-bit OS\_RATIO to the OVERSAMPLE register while clearing OS\_EN to 0. Then reprogram the register with the chosen OS\_RATIO while setting OS\_EN to 1. This sequence ensures the next CNV rising edge is interpreted as the first sample of oversampling mode.

As shown in Figure 51, in oversampling mode, the BUSY line transitions low-to-high at the start of the first conversion of the oversampling window and remains high through the end of the final conversion of the window. Though the BUSY line remains high, separate CNV rising edges are still required to begin each conversion within the oversampling window. Averaged results for each analog input channel are updated on the SDO0 to SDO7 lines (CMOS) or SDO lines (LVDS) at the end of each oversampling window, just prior to the falling edge of the BUSY line.

![Figure 51. Oversampling Mode with 4× Oversampling Ratio (OS_RATIO = 0x1)](ad4858/figures/ad4858-f052.png)

*Figure 51. Oversampling Mode with 4× Oversampling Ratio (OS_RATIO = 0x1)*

### Digital Offset Correction
<!-- page: 33 -->

Each channel of the AD4858 can be independently programmed to add a 20-bit signed digital offset correction value to every conversion result. This feature can be used to correct for fixed offset errors upstream to the DAS analog inputs. The default offset correction for all channels is zero. To employ a nonzero value, compute the 20-bit signed offset correction CHx\_OFFSET using the following equation:

$$\mathrm{Digital\ Offset\ Correction}\ (\mu V) \\=CH_x\_OFFSET\ ×\ LSB\ Size\ (\mu V)$$

where LSB size is a function of the channel SoftSpan range, as shown in Table 12. Program the 20-bit signed offset correction to the corresponding CHx\_OFFSET register, shown in Table 14.

Offset correction is added to the conversion results of a channel prior to output code saturation. Code saturation occurs at zero scale and positive full scale for unipolar SoftSpan ranges, and it occurs at negative and positive full scale for bipolar SoftSpan ranges. Because offset correction precedes output code saturation, artifacts may be introduced near negative or positive full scale, depending on the magnitude and the polarity of the digital offset employed. The AD4858 offers approximately 5% additional analog input range beyond the SoftSpan range limits shown in Table 12. This additional analog input span is usually not observable due to the output code saturation but can be observed using a combination of digital offset and gain correction terms.

Table 14. Per Channel Offset Correction Registers

| Register Name   | Register Addresses   |
|-----------------|----------------------|
| CH0_OFFSET      | 0x2B to 0x2D         |
| CH1_OFFSET      | 0x3D to 0x3F         |
| CH2_OFFSET      | 0x4F to 0x51         |
| CH3_OFFSET      | 0x61 to 0x63         |
| CH4_OFFSET      | 0x73 to 0x75         |
| CH5_OFFSET      | 0x85 to 0x87         |
| CH6_OFFSET      | 0x97 to 0x99         |
| CH7_OFFSET      | 0xA9 to 0xAB         |

### Digital Gain Correction
<!-- page: 33 -->

Each channel of the AD4858 can be independently programmed to apply a digital gain correction factor to every conversion result. This can be used to correct for fixed gain errors upstream to the DAS analog inputs. The default gain correction factor for all channels is 1.00000. To employ a nonunity factor, compute the 16-bit unsigned gain correction CHx\_GAIN using the following equation:

$$\textit{Digital Gain Correction} = \frac{\mathrm{CHx\_GAIN}}{0x8000}$$

Program the value from this equation into the corresponding CHx\_GAIN register, shown in Table 15. The gain correction factor spans 0 to 1.99997 as CHx\_GAIN traverses 0x0000 to 0xFFFF, with the default of 1.00000 corresponding to CHx\_GAIN = 0x8000.

Gain correction is applied to the conversion results of a channel after the digital offset correction and prior to the output code saturation. Code saturation occurs at zero scale and positive full scale for unipolar SoftSpan ranges and at negative and positive full scale for bipolar SoftSpan ranges. Because gain correction precedes output code saturation, artifacts may be introduced near negative or positive full scale depending on the magnitude of digital gain employed. The AD4858 offers approximately 5% additional analog input range beyond the SoftSpan range limits shown in Table 12. This additional analog input span is usually not observable due to the output code saturation but can be observed using a combination of digital offset and gain correction terms.

**Table 15. Per Channel Gain Correction Registers** ([table-14-p33-register.csv](ad4858/tables/table-14-p33-register.csv), p. 33)

| Register Name | Register Addresses |
|---|---|
| CH0_GAIN | 0x2E to 0x2F |
| CH1_GAIN | 0x40 to 0x41 |
| CH2_GAIN | 0x52 to 0x53 |
| CH3_GAIN | 0x64 to 0x65 |
| CH4_GAIN | 0x76 to 0x77 |
| CH5_GAIN | 0x88 to 0x89 |
| CH6_GAIN | 0x9A to 0x9B |
| CH7_GAIN | 0xAC to 0xAD |

### Digital Phase Correction
<!-- page: 33 -->

While operating in Oversampling Mode, each channel of the AD4858 can be independently programmed to apply a digital phase correction term to the oversampled digital averages. This feature may be used to compensate for phase errors upstream to the DAS analog inputs. The default phase correction for all channels is zero, which results in digital averages of all channels being computed using the same phase-aligned sample groups (for example, Sample 1 to Sample 4, Sample 5 to Sample 8, Sample 9 to Sample 12, and so forth) as shown in Figure 51.

To employ digital phase correction, program the desired 16-bit unsigned phase correction term (in integer number of conversion cycles) to the corresponding CHx\_PHASE register, shown in Table 16. The maximum phase correction allowed is one less than the number of conversions in the oversampling ratio. Comparing Figure 52 with Figure 51, the oversampled digital average of a channel with nonzero phase is shifted by an integer number of conversion cycles relative to the start of oversampling. The oversampled average data for all channels are updated on the SDO0 to SDO7 lines (CMOS) or the SDO lines (LVDS) once the values for all channels are available, just prior to the falling edge of the BUSY line. The averaged results of all channels in Figure 52 are updated one conversion cycle later than in Figure 51 due to the CH7\_PHASE = 0x0001 setting.

<!-- page: 34 -->

**Table 16. Per Channel Phase Correction Registers** ([table-15-p34-register.csv](ad4858/tables/table-15-p34-register.csv), p. 34)

| Register Name | Register Addresses |
|---|---|
| CH0_PHASE | 0x30 to 0x31 |
| CH1_PHASE | 0x42 to 0x43 |
| CH2_PHASE | 0x54 to 0x55 |
| CH3_PHASE | 0x66 to 0x67 |
| CH4_PHASE | 0x78 to 0x79 |
| CH5_PHASE | 0x8A to 0x8B |
| CH6_PHASE | 0x9C to 0x9D |
| CH7_PHASE | 0xAE to 0xAF |

![Figure 52. Oversampling Mode with 4× Oversampling Ratio (OS_RATIO = 0x1), Channel 7 Averages Phase-Shifted by One Sample (CH7_PHASE = 0x0001)](ad4858/figures/ad4858-f053.png)

*Figure 52. Oversampling Mode with 4× Oversampling Ratio (OS_RATIO = 0x1), Channel 7 Averages Phase-Shifted by One Sample (CH7_PHASE = 0x0001)*

### Channel Overrange and Underrange Limits
<!-- page: 35 -->

Every conversion result on each channel of the AD4858 is compared with the 20-bit signed overrange and underrange limits CHx\_OR and CHx\_UR, shown in Table 17 and Table 18. If any out-of-range conversion result is detected, the corresponding flag in the CH\_OR\_STATUS register or CH\_UR\_STATUS register is set. This limit checking is particularly useful during Oversampling Mode, as it allows the digital host to determine if any out-of-range conversion results contributed to an oversampled digital average. The default overrange and underrange limits are positive and negative full scale of a bipolar input range, respectively. To employ other limits, program the desired 20-bit signed code limits to the corresponding CHx\_OR and CHx\_UR registers, shown in Table 17 and Table 18.

Table 17. Per Channel Overrange Limit Registers

| Register Name   | Register Addresses   |
|-----------------|----------------------|
| CH0_OR          | 0x32 to 0x34         |
| CH1_OR          | 0x44 to 0x46         |
| CH2_OR          | 0x56 to 0x58         |
| CH3_OR          | 0x68 to 0x6A         |
| CH4_OR          | 0x7A to 0x7C         |
| CH5_OR          | 0x8C to 0x8E         |
| CH6_OR          | 0x9E to 0xA0         |
| CH7_OR          | 0xB0 to 0xB2         |

Table 18. Per Channel Underrange Limit Registers

| Register Name   | Register Addresses   |
|-----------------|----------------------|
| CH0_UR          | 0x35 to 0x37         |
| CH1_UR          | 0x47 to 0x49         |
| CH2_UR          | 0x59 to 0x5B         |
| CH3_UR          | 0x6B to 0x6D         |
| CH4_UR          | 0x7D to 0x7F         |
| CH5_UR          | 0x8F to 0x91         |
| CH6_UR          | 0xA1 to 0xA3         |
| CH7_UR          | 0xB3 to 0xB5         |

### APPLICATIONS INFORMATION
<!-- pages: 36-41 -->

### BUFFERED ANALOG INPUTS
<!-- page: 36 -->

Each channel of the AD4858 simultaneously samples the voltage difference (V_{INx+} - V_{INx}) between its analog input pins over a wide common-mode input range while high CMRR attenuates unwanted signals common to both inputs. Wide common-mode input range coupled with high CMRR allows the INx+ and INx- analog inputs to swing with an arbitrary relationship to each other, provided each pin remains between (V_{EE} + 3.2 V) and (V_{CC} - 3.2 V). This feature of the AD4858 simplifies signal chain design by accepting a wide variety of signal swings, including traditional classes of analog input signals (such as pseudo-differential unipolar, pseudo-differential true bipolar, and fully differential).

The wide operating ranges of the buffer V_{CC} and V_{EE} supplies offer further input common-mode flexibility. As long as the voltage difference limits of 10 V ≤ (V_{CC} - V_{EE}) ≤ 48 V are observed, the V_{CC} and V_{EE} supplies can be independently biased anywhere within their own individually allowed operating ranges, including the ability for the V_{EE} pin to be tied directly to ground. This feature enables the absolute input range of the AD4858 to be tailored to specific application requirements.

In all SoftSpan ranges, the analog inputs of each channel can be modeled by the equivalent circuit shown in Figure 53. At the start of acquisition, the sampling capacitors (C_{SAMP} ) connect to the integrated buffers, BUFFER+ and BUFFER-, through the sampling switches. The sampled voltage is reset during the conversion process and is, therefore, reacquired for each new conversion. As shown in Figure 17 and Figure 20, the wideband analog-input buffers are well-suited to acquiring inputs signals that undergo transient step settling between successive conversions. To ensure best performance, limit the analog-input signal slew rate to less than 100 V/µs at the sampling moment.

![Figure 53. Equivalent Circuit for Differential Analog Inputs, Single Channel](ad4858/figures/ad4858-f054.png)

*Figure 53. Equivalent Circuit for Differential Analog Inputs, Single Channel*

The diodes between the inputs and the V_{CC} and V_{EE} supplies provide input ESD protection. While within the supply voltages, the analog inputs of the AD4858 draw only 75 pA typical DC leakage current, and the ESD protection diodes do not turn on. This protection offers a significant advantage over external op amp buffers, which often have diode protection that turns on during transients, injecting a current into the input signal path that corrupts the signal voltage.

### ANALOG INPUT DRIVE CIRCUITS
<!-- page: 36 -->

The buffer input stage offers a high degree of transient isolation from the sampling process. Most sensors, signal conditioning amplifiers, and filter networks with less than 10 kΩ of impedance can drive the passive 4 pF analog input capacitance (C_{PIN} ) directly. For higher impedances and slow-settling circuits, add a 680 pF capacitor between the analog-input pins and the GND pins to maintain the full DC accuracy of the AD4858.

The high input impedance of the unity-gain buffers in the AD4858 reduces the input drive requirements, and it enables the inclusion of optional RC filters with kΩ impedance and arbitrarily slow time constants for anti-aliasing or other purposes. Micropower op amps with limited drive capability are also well-suited to driving the high impedance analog inputs directly.

The AD4858 features proprietary circuitry to achieve 120 dB typical internal crosstalk isolation between channels. Maintaining this level of isolation may require care with the PCB layout. Ensure input signal traces are short and well shielded to minimize external coupling. Capacitive coupling between the input pins of different channels of the AD4858 is tens of femtofarads, orders of magnitude below the coupling that may be present in a poor PCB design. Low source resistance and/or high source capacitance help reduce external capacitively-coupled crosstalk. A single-ended input drive also enjoys additional external crosstalk isolation because every other input pin is grounded or at a low-impedance source, and it serves as a shield between channels.

### ANALOG INPUT OVERDRIVE TOLERANCE
<!-- page: 36 -->

Driving an analog input greater than the V_{CC} supply on any channel up to 10 mA does not affect conversion results on other channels. Approximately 70% of this overdrive current flows out of the V_{CC} pin, and the remaining 30% flows out of the V_{EE} pin. The current flowing out of V_{EE} will produce heat across the V_{CC} - V_{EE} voltage drop and must be taken into account for the absolute maximum operating junction temperature. Driving an analog input below the V_{EE} supply may corrupt the conversion results on other channels.

Adding an external resistor (for example, 100 Ω to 1000 Ω) in series with each INx+ and INx- pin is recommended in applications where (V_{CC} - V_{EE} ) > 44 V to limit latchup current to under ±10 mA during fault conditions, as shown in Figure 54. These resistors are transparent in normal operation of the AD4858. Refer to Absolute Maximum Ratings in Table 6 for pin voltage and current limits related to device reliability.

Driving the inputs greater than V_{CC} or less than V_{EE} can reverse the normal current flow from the external power supplies driving these pins.

![Figure 54. External Series Resistors Limit Latchup Current During Fault Conditions and are Transparent in Normal Operation](ad4858/figures/ad4858-f055.png)

*Figure 54. External Series Resistors Limit Latchup Current During Fault Conditions and are Transparent in Normal Operation*

### ANALOG INPUT FILTERING
<!-- page: 37 -->

The true high impedance analog inputs can accommodate a very wide range of passive or active signal conditioning filters. The buffered DAS inputs have an analog bandwidth of 11 MHz and impose no particular bandwidth requirement on external filters. Any external input filters can, therefore, be optimized independently of the DAS to reduce signal chain noise and interference. A common filter configuration is the simple antialiasing and noise reducing RC filter with its pole at half the sampling frequency, as shown in Figure 55.

![Figure 55. Example Differential Input Filter](ad4858/figures/ad4858-f056.png)

*Figure 55. Example Differential Input Filter*

Use high quality capacitors and resistors in the RC filters because these components may add distortion. Ceramic capacitors with NPO/COG type dielectric have excellent linearity. Carbon surface mount resistors may generate distortion from self heating and from damage that may occur during soldering. Metal film surface mount resistors are much less susceptible to either problem.

### DAS REFERENCE
<!-- page: 37 -->

The AD4858 supports three reference configurations as follows:

- Internal band-gap reference and reference buffer
- External reference and internal reference buffer
- External reference and external reference buffer

Most applications employ the internal band-gap reference and reference buffer, which is the default configuration of the AD4858. For applications requiring better initial accuracy and/or lower reference temperature drift, disable the internal band-gap reference and overdrive the REFIO pin with an external reference. This configuration (external reference and internal reference buffer) retains the internal reference buffer, isolating the external reference from ADC conversion transients, and is ideal for sharing a single precision external reference across multiple devices. The final configuration (external reference and external reference buffer) disables the internal band-gap reference and the internal reference buffer, and overdrives the REFBUF pin with an external reference.

### Internal Reference with Internal Buffer
<!-- page: 37 -->

The AD4858 includes a low noise, low drift (10 ppm/°C maximum), temperature compensated band-gap reference that is factory trimmed to 4.096 V. The reference output connects to the REFIO pin, which serves as the input to the on-chip reference buffer (see Figure 56). The REFIO pin is internally bypassed to the GND pins with a 10 nF ceramic capacitor to filter wideband noise of the band-gap reference. The precision unity-gain reference buffer creates the converter main reference voltage (V_{REFBUF} = V_{REFIO}) on the REFBUF pin, nominally 4.096 V when using the internal band-gap reference.

The internal band-gap reference PSRR vs. frequency is shown in Figure 32. For best performance, supply the V_{DD} pin using a highPSRR, low-noise LDO regulator, such as the LT3042. Optionally, adding an external 100 µF, X5R, and 0805 capacitor between the REFIO pin and the GND pin B4 can significantly improve the PSRR of the internal reference at frequencies between 100 Hz and 1 MHz.

![Figure 56. Internal Reference with Internal Buffer Configuration](ad4858/figures/ad4858-f057.png)

*Figure 56. Internal Reference with Internal Buffer Configuration*

### External Reference with Internal Buffer
<!-- page: 37 -->

If better initial accuracy and/or lower reference temperature drift is required, the REFIO pin can be overdriven by an external reference, as shown in Figure 57. With its small size, low power, and high accuracy, the LTC6655-4.096 is well-suited for use with the AD4858 when overdriving the REFIO pin. Bypassing the LTC6655-4.096 to the GND pin B4 with a 10 µF X5R 0805 ceramic capacitor close to the REFIO pin is recommended. Disable the internal band-gap reference through the DEVICE\_CTRL register in this configuration.

This configuration retains the internal reference buffer, isolating the external reference from the ADC conversion transients. It is ideal for sharing a single precision external reference across multiple devices. It also offers the best transient response performance when employing burst sampling, as explained in the Internal Reference Buffer Transient Response section.

![Figure 57. External Reference with Internal Buffer Configuration](ad4858/figures/ad4858-f058.png)

*Figure 57. External Reference with Internal Buffer Configuration*

### External Reference with Disabled Internal Buffer
<!-- page: 38 -->

In applications employing an external reference, the External Reference with Internal Buffer configuration is the recommended use case. In the rare case that it is necessary, the AD4858 supports overdriving the REFBUF pin directly with an external reference as shown in Figure 58. With its small size, low power, and high accuracy, the LTC6655-4.096 is well-suited for use with the AD4858 when overdriving the REFBUF pin. Bypass the LTC6655-4.096 to the GND pin B4 with a 47 µF X5R 0805 ceramic capacitor close to the REFBUF pin to absorb transient conversion currents and minimize noise. Disable the internal band-gap reference and the internal reference buffer through the DEVICE\_CTRL register in this configuration and connect the REFIO pin to the GND pins.

![Figure 58. External Reference with Disabled Internal Buffer Configuration](ad4858/figures/ad4858-f059.png)

*Figure 58. External Reference with Disabled Internal Buffer Configuration*

The AD4858 converters draw a charge (Q_{CONV} ) from the REFBUF pin during each conversion cycle. The internal reference buffer is designed to optimally provide this charge, minimizing V_{REFBUF} movement. If the internal buffer is disabled, the external reference circuitry on the REFBUF pin must supply this charge. On short time scales, the charge is provided by the external bypass capacitor, but on longer time scales, all of the charge is supplied by the external reference. This charge draw corresponds to a DC current equivalent of I_{REFBUF} = Q_{CONV} × f_{S} , which is proportional to sample rate. In applications where a burst of samples is taken after idling for long periods of time (see Figure 59), the I_{REFBUF} quickly transitions from approximately 2.2 mA to 3.3 mA (V_{REFBUF} = 4.096 V, f_{S} = 1 MSPS). This current step triggers a transient response in the external reference that must be considered, because any deviation in the V_{REFBUF} affects converter accuracy. If an external reference is used to overdrive the REFBUF pin, the fast settling LTC6655 family of references is recommended.

![Figure 59. CNV Waveform Showing Burst Sampling](ad4858/figures/ad4858-f060.png)

*Figure 59. CNV Waveform Showing Burst Sampling*

### Internal Reference Buffer Transient Response
<!-- page: 38 -->

For optimum performance in applications employing burst sampling, use the internal reference buffer. The internal reference buffer incorporates a proprietary design that minimizes movements in the V_{REFBUF} when responding to a burst of conversions following an idle period. Figure 60 compares the burst conversion response of the AD4858 with a DC input level for the three supported reference configurations. The first configuration employs the internal reference and reference buffer as shown in Figure 56. The second employs the internal reference buffer with the REFIO pin externally overdriven by an LTC6655-4.096, as shown in Figure 57. The third configuration disables the internal reference buffer and overdrives the REFBUF pin with an external LTC6655-4.096, as shown in Figure 58.

![Figure 60. Burst Conversion Response of the AD4858, f_{S} = 1 MSPS](ad4858/figures/ad4858-f061.png)

*Figure 60. Burst Conversion Response of the AD4858, f_{S} = 1 MSPS*

### POWER CONSIDERATIONS
<!-- page: 38 -->

The AD4858 requires the following five power supplies:

- V_{CC}  and V_{EE} , the positive and negative analog input buffer supplies
- V_{DD} , the 5 V core power supply
- V_{DDH}  (or V_{DDL} ), the 1.8 V_{LDO} (or 1.8 V core) power supply
- V_{IO} , the digital input and output power supply

All five power supplies have internal bypass capacitance, and no additional external bypass is required or recommended.

### APPLICATIONS INFORMATION

The V_{CC} and V_{EE} supplies can be independently biased anywhere within their individual allowable operating ranges, including the ability for the V_{EE} supply to be tied directly to the ground. This feature enables the absolute input range of the AD4858 to be tailored to the specific requirements of the application.

In the recommended use case the V_{DDL} pin is supplied by the internal 1.8 V_{LDO], as shown in Figure 1. Tie the V_{DDH} pin to the V_{DD} pin or to another external supply between 2.2 V and 5.25 V, and do not externally connect the V_{DDL} pin in this case. To externally supply the V_{DDL} pin, disable the internal LDO by tying the V_{DDH}  pin to the GND pins and connect the V_{DDL} pin to an external 1.8 V supply, as shown in Figure 61.

The flexible V_{IO} supply allows the AD4858 to communicate with the CMOS logic operating between 0.9 V and 5.25 V (controlled by the HIVIO/L̅O̅V̅I̅O̅ pin logic state), including 2.5 V and 3.3 V systems. When using LVDS data output mode, the range of the V_{IO} supply is 1.71 V to 5.25 V (controlled by the HIVIO/L̅O̅V̅I̅O̅ pin logic state). See Table 1 and Table 9 for more details.

![Figure 61. Power Supply Pins of the AD4858 when V_{DDL} is supplied externally](ad4858/figures/ad4858-f062.png)

*Figure 61. Power Supply Pins of the AD4858 when V_{DDL} is supplied externally*

Digitized data: [burst-conversion-response-of-the-ad4858-f-s-1-msps.csv](ad4858/curves/burst-conversion-response-of-the-ad4858-f-s-1-msps.csv) (x: µs; y: µV) — values read off the printed plot by the digitizer, not published data.

### Power Supply Sequencing
<!-- page: 39 -->

The AD4858 does not have any specific power supply sequencing requirements. Take care to adhere to the maximum voltage relationships described in the Absolute Maximum Ratings section. The AD4858 has an internal power-on-reset circuit that resets the converter on initial power up and whenever the V_{DD} supply drops to less than 3.4 V or the V_{DDL} supply drops to less than 1.2 V. Once the supply voltage reenters the nominal supply voltage range, the power-on-reset circuit reinitializes the DAS. Do not initiate any conversions until at least the maximum t_{WAKE} (t_{WAKE,MAX} ) = 1 ms after the falling edge of the BUSY line, which indicates the end of the power-on-reset event. Any conversion initiated before this time produces invalid results.

### TIMING AND CONTROL
<!-- page: 39 -->

The AD4858 sampling and conversion is controlled by the CNV pin. A rising edge on the CNV pin transitions the sample-and-hold circuits of all channels from track mode to hold mode, simultaneously sampling the input signals on all channels and initiating a conversion. Once a conversion is started, it cannot be terminated early except by resetting the DAS (see the Reset Timing section). For optimum performance, drive the CNV pin with a clean, low jitter signal and avoid transitions on data input and output lines leading up to the rising edge of the CNV pin. Additionally, avoid high slew rates on the analog inputs for 100 ns before and after the rising edge of the CNV pin. Converter status is indicated by the BUSY output, which transitions low-to-high at the start of each conversion and stays high until the conversion is complete. After the CNV pin is brought high to begin a conversion, it must be returned low between 40 ns and 60 ns later or after the falling edge of the BUSY line to minimize external disturbances during the internal conversion process. The CNV timing required to take advantage of reduced power at slower sampling rates is described in the Nap Mode section.

The AD4858 has an internal clock that is trimmed to guarantee a maximum conversion time of 725 ns and a minimum acquisition time of 465 ns when converting at 1 MSPS. The architecture of the AD4858 allows the converter to begin acquiring the next sample before the conversion of the previous sample is completed, as shown in Figure 2. The minimum acquisition time varies with the sampling frequency.

### Nap Mode
<!-- page: 39 -->

The AD4858 can be placed into nap mode after a conversion is completed to reduce power consumption between conversions. In this mode, a portion of the device circuitry is turned off, including circuits associated with sampling the analog input signals. Nap mode is enabled by keeping the CNV pin high between conversions, as shown in Figure 62. To initiate a new conversion after entering nap mode, bring the CNV pin low and hold for at least 750 ns before bringing it high again. The converter acquisition time is set by the CNV pin low time when using nap mode.

![Figure 62. Nap Mode Timing for the AD4858](ad4858/figures/ad4858-f063.png)

*Figure 62. Nap Mode Timing for the AD4858*

### Power-Down Mode
<!-- page: 39 -->

When the PD pin is brought high or the PWR\_MODE field in the Device Configuration Register is set to 0x3, the AD4858 is powered down and subsequent conversion requests are ignored. If this occurs during a conversion, the device powers down once the conversion completes. In this mode, the AD4858 draws only a small standby current resulting in a typical power dissipation of 1.3 mW. To exit power-down mode, bring the PD pin low and wait at least t_{WAKE,MAX} = 1 ms before initiating a conversion. Any conversion initiated before this time produces invalid results.

### Channel Sleep
<!-- page: 39 -->

Each channel in the AD4858 can be independently put into sleep mode to reduce power consumption. With sleep mode enabled, the input buffers and ADC of a channel are placed in a low-power standby state, and conversion requests are ignored. Sleep mode is disabled on all channels by default. To enable sleep mode on a channel, set the corresponding control bit in the CH\_SLEEP register.

### Reset Timing
<!-- page: 39 -->

A global reset of the AD4858, equivalent to a power-on-reset event, can be executed without needing to cycle the supplies. This feature is useful when recovering from system-level events that require the entire system to be reset to a known synchronized state. To initiate a global reset, bring the PD pin high twice without an intervening conversion, as shown in Figure 63 . Alternatively, an equivalent global reset may be triggered by entering, exiting, and then reentering power-down mode using the PWR\_MODE field in the Device Configuration Register without an intervening conversion.

The reset event is triggered on the second rising edge of the PD pin and asynchronously ends based on an internal timer. Reset clears all serial data output registers and restores all device states to their POR default conditions. If reset is triggered during a conversion, the conversion is immediately halted. The normal power-down behavior associated with the PD pin going high is not affected by reset. Once the PD pin is brought low, wait at least t_{WAKE,MAX} = 1 ms before initiating a conversion. Any conversion initiated before this time produces invalid results.

![Figure 63. Reset Timing for the AD4858](ad4858/figures/ad4858-f064.png)

*Figure 63. Reset Timing for the AD4858*

### DIGITAL INTERFACE
<!-- pages: 41-50 -->

The AD4858 supports both CMOS (see Figure 64) and LVDS (see Figure 69) serial conversion data output interfaces, selectable using the LVDS/C̅M̅O̅S̅ pin. The flexible V_{IO} supply allows the AD4858 to communicate with any CMOS logic operating between 0.9 V and 5.25 V (controlled by the HIVIO/L̅O̅V̅I̅O̅ pin logic state), while the LVDS interface supports low noise digital systems. In CMOS conversion data output mode, applications may employ between one and eight lanes of serial data output, allowing for optimized bus width and conversion data throughput.

### CMOS CONVERSION DATA OUTPUT MODE
<!-- page: 41 -->

As shown in Figure 64 and Figure 65, the serial CMOS conversion data output bus consists of the following lines:

- One serial clock input (SCKI)
- One serial clock output (SCKO)
- Eight serial data output lanes (SDO0 to SDO7)

Communication with the AD4858 across this bus occurs during predefined data transaction windows. Within a window, the device outputs user-configurable packets containing either conversion or oversampling results, optional channel configuration, and device status information from the SDO0 lane to the SDO7 lane. Following the eighth channel packet, a ninth packet containing device status and 16-bit cyclic redundanct check (CRC) may be read out for diagnostic and error checking purposes. The AD4858 supports three user-selectable packet sizes from 20-bits to 32-bits in length (see the Packet Format section).

Complete the data transaction with a minimum last SCKI signal edge to CNV signal rising edge time (t_{SCKICNV,MIN} ) = 20 ns prior to the start of the next conversion (see Figure 64). It is still possible to read packets after starting the next conversion, but this degrades conversion accuracy and, therefore, is not recommended.

Just prior to the falling edge of the BUSY pin, the SDO0 lane to the SDO7 lane are updated with the latest conversion or oversampling results from analog input Channels 0 to Channel 7, respectively. Rising edges on the SCKI signal serially clock data out on the SDO0 lane to the SDO7 lane. The SCKO signal echoes the SCKI signal but is skew-matched with data on the SDO0 lane to the SDO7 lane. The SCKI signal is allowed to idle either high or low in CMOS mode. The CMOS conversion data output bus is enabled when the C̅S̅ signal is low, and it is disabled and high-Z when C̅S̅ is high, allowing the bus to be shared across multiple devices.

When interfacing the AD4858 with a standard SPI host, capture output data at the receiver on rising edges of the SCKI signal. In other applications, such as interfacing the AD4858 with an FPGA, the SCKO signal may be used to capture serial output data from the SDO0 lane to the SDO7 lane at the receiver. Capturing data using the SCKO signal adds robustness to delay variations over temperature and supply.

As shown in Figure 64 and Figure 66, each SDO lane outputs packets for all analog input channels in a sequential circular manner. For example, the first packet output on the SDO0 lane corresponds to analog input Channel 0, followed by the packets for Channel 1 through Channel 7. Finally, the packet containing the device status and 16-bit CRC can be read out. The data output on the SDO0 lane then wraps back to Channel 0, and this pattern repeats indefinitely. Other SDO lanes follow a similar circular pattern-except the first packet presented on each lane corresponds to its associated analog input channel. To achieve full 1 MSPS per channel throughput, data packets must be captured from all eight SDO data output lanes in parallel. In applications that do not require full throughput, increasing the number of SCKI pulses applied during the data transaction window allows all data packets to be read using fewer physical SDO lanes.

![Figure 64. CMOS Conversion Data Bus Timing, PACKET_SIZE = 0x1, OS_EN = 0, TEST_PAT = 0](ad4858/figures/ad4858-f065.png)

*Figure 64. CMOS Conversion Data Bus Timing, PACKET_SIZE = 0x1, OS_EN = 0, TEST_PAT = 0*

### DIGITAL INTERFACE

![Figure 65. CMOS Conversion Data Output Mode](ad4858/figures/ad4858-f066.png)

*Figure 65. CMOS Conversion Data Output Mode*

![Figure 66. All Packets May Be Read Using Fewer SDO Lanes By Increasing the Number of SCKI Pulses Applied](ad4858/figures/ad4858-f067.png)

*Figure 66. All Packets May Be Read Using Fewer SDO Lanes By Increasing the Number of SCKI Pulses Applied*

### LVDS CONVERSION DATA OUTPUT MODE
<!-- page: 42 -->

In LVDS conversion data output mode, information is transmitted using positive and negative signal pairs with bits differentially encoded as (LVDS+ - LVDS-). These signals are typically routed using differential transmission lines with 100 Ω characteristic impedance. Logical 1s and Logical 0s are nominally represented by differential +350 mV and -350 mV, respectively.

As shown in Figure 69, the serial LVDS conversion data output bus consists of the following lines:

- SCKI+ and SCKI-, the differential serial clock input pair
- SCKO+ and SCKO-, the differential serial clock output pair
- SDO+ and SDO-, the differential serial data output pair

Communication with the AD4858 across this bus occurs during predefined data transaction windows. Within a window, the device outputs user-configurable packets containing the conversion or oversampling results, optional channel configuration, and device status information on the SDO line. Following the eighth channel packet, a ninth packet containing device status and 16-bit CRC can be read out for diagnostic and error checking purposes. The AD4858 supports three user-selectable packet sizes from 20-bits to 32-bits in length (see the Packet Format section).

Complete the data transaction with a minimum t_{SCKICNV,MIN} = 20 ns prior to the start of the next conversion, as shown in Figure 69. It is still possible to read packets after starting the next conversion, but this degrades conversion accuracy and is not recommended.

Just prior to the falling edge of the BUSY signal, the SDO line is updated with the latest conversion or oversampling results from analog input Channel 0. Both rising and falling edges on the SCKI signal serially clock data out on the SDO line. The SCKI signal is also echoed on the SCKO signal, skew-matched to the data on the SDO line.

Whenever possible, it is recommended that rising and falling edges of the SCKO line be used to capture double data rate (DDR) serial output data on the SDO line, as this yields the best robustness to delay variations over supply and temperature. The LVDS bus is enabled when the C̅S̅ signal is low. It is disabled and high-Z when the C̅S̅ signal is high, allowing the bus to be shared across multiple devices. Due to the high speeds involved in LVDS signaling, LVDS bus sharing must be carefully considered. Transmission line limitations imposed by the shared bus may limit the maximum achievable bus clock speed. The LVDS inputs are internally terminated with a 100 Ω differential resistor when the C̅S̅ signal is low, while outputs must be differentially terminated with a 100 Ω resistor at the receiver (FPGA). The SCKI line must idle in the low state in LVDS output mode, including when transitioning the C̅S̅ signal.

As shown in Figure 69 and Figure 68, the SDO line outputs data packets for all analog input channels in a sequential circular manner. For example, the first packet output on the SDO line corresponds to analog input Channel 0, followed by the packet for Channel 1 all the way to Channel 7. Finally, a packet containing device status and 16-bit CRC can be read out. The data output on the SDO line then wraps back to Channel 0, and this pattern repeats indefinitely.

![Figure 67. LVDS Conversion Data Output Mode](ad4858/figures/ad4858-f068.png)

*Figure 67. LVDS Conversion Data Output Mode*

![Figure 68. All Packets Are Sequentially Output on SDO+ and SDO-](ad4858/figures/ad4858-f069.png)

*Figure 68. All Packets Are Sequentially Output on SDO+ and SDO-*

![Figure 69. LVDS Serial Conversion Data Bus Timing, PACKET_SIZE = 0x1, OS_EN = 0, TEST_PAT = 0](ad4858/figures/ad4858-f070.png)

*Figure 69. LVDS Serial Conversion Data Bus Timing, PACKET_SIZE = 0x1, OS_EN = 0, TEST_PAT = 0*

### PACKET FORMAT
<!-- page: 42 -->

Data provided on the CMOS and LVDS conversion data output buses are packaged into eight channel packets and a ninth status packet, as shown in Figure 66 and Figure 68. Packet data formats are a function of packet size, oversampling mode, and test pattern configuration. The AD4858 offers three user-selectable packet sizes: 20-bit, 24-bit, and 32-bit. The default packet size is 24-bit.

### Nonoversampling Packet Formats
<!-- page: 44 -->

With the AD4858 configured in nonoversampling mode, the channel and status packet data formats shown in Figure 70 are available. Select from these packet options using the 2-bit PACKET\_SIZE field in the PACKET register. The channel packets include 20-bit conversion results plus options to report overrange or underrange of the conversion result, channel number identification, and channel SoftSpan identification. The status packet includes DEVICE\_STA-TUS register state information and a 16-bit CRC computed for all data in the eight channel packets plus the ninth status packet.

The following CRC polynomial is used to calculate the checksums: 

$$x^{16}+x^{14}+x^{13}+x^{12}+x^{10}+x^{8}+x^{6}+x^{4}+x^{3}+x+1$$

where the initial value for the CRC calculation is 0x0000 in all transactions.

![Figure 70. Channel and Status Packet Data Formats in Nonversampling Mode (OS_EN = 0), Test Pattern Output is Disabled (TEST_PAT = 0)](ad4858/figures/ad4858-f071.png)

*Figure 70. Channel and Status Packet Data Formats in Nonversampling Mode (OS_EN = 0), Test Pattern Output is Disabled (TEST_PAT = 0)*

### Oversampling Packet Formats
<!-- page: 44 -->

With the AD4858 configured in oversampling mode, the channel and status packet data formats shown in Figure 71 are available. Select from these packet options using the 2-bit PACKET\_SIZE field in the PACKET register. The channel packets include 20-bit or 24-bit averaged conversion results plus options to report the overrange or the underrange of any conversion included in the averaged result, channel number identification, and channel SoftSpan identification. The status packet includes DEVICE\_STATUS register state information and a 16-bit CRC computed for all data in the eight channel packets and the ninth status packet.

The following CRC polynomial is used to calculate the checksums: 

$$x^{16}+x^{14}+x^{13}+x^{12}+x^{10}+x^{8}+x^{6}+x^{4}+x^{3}+x+1$$

where the initial value for the CRC calculation is 0x0000 in all transactions.

![Figure 71. Channel and Status Packet Data Formats in Oversampling Mode (OS_EN = 1), Test Pattern Output is Disabled (TEST_PAT = 0)](ad4858/figures/ad4858-f072.png)

*Figure 71. Channel and Status Packet Data Formats in Oversampling Mode (OS_EN = 1), Test Pattern Output is Disabled (TEST_PAT = 0)*

### Test Pattern Packet Format
<!-- page: 46 -->

The AD4858 offers a test pattern data output option that can be used to validate the CMOS or LVDS conversion data output bus operation. To enable this mode, set the TEST\_PAT field to 1 in the PACKET register. When the test pattern data output is enabled, the channel and status packet data formats shown in Figure 72 are available. Select from these packet options using the 2-bit PACK-ET\_SIZE field in the PACKET register. The channel packet data in this mode are defined by the data in the CHx\_TESTPAT registers, shown in Table 19. In their default state the CHx\_TESTPAT registers contain a channel number identification in the most-significant nibble followed by a fixed pattern of 0xACE3C2A. Update these registers to match the test patterns required by the application. The status packet contains a 16-bit CRC computed for all data in the eight channel packets and the ninth status packet.

### Table 19. Per Channel Test Pattern Registers
<!-- page: 46 -->

**Table 19. Per Channel Test Pattern Registers** ([table-18-p46-register.csv](ad4858/tables/table-18-p46-register.csv), p. 46)

| Register Name | Register Addresses | Default Pattern |
|---|---|---|
| CH0_TESTPAT | 0x38 to 0x3B | 0x0ACE3C2A |
| CH1_TESTPAT | 0x4A to 0x4D | 0x1ACE3C2A |
| CH2_TESTPAT | 0x5C to 0x5F | 0x2ACE3C2A |
| CH3_TESTPAT | 0x6E to 0x71 | 0x3ACE3C2A |
| CH4_TESTPAT | 0x80 to 0x83 | 0x4ACE3C2A |
| CH5_TESTPAT | 0x92 to 0x95 | 0x5ACE3C2A |
| CH6_TESTPAT | 0xA4 to 0xA7 | 0x6ACE3C2A |
| CH7_TESTPAT | 0xB6 to 0xB9 | 0x7ACE3C2A |

![Figure 72. Channel and Status Packet Data Formats with Test Pattern Output Enabled (TEST_PAT = 1)](ad4858/figures/ad4858-f073.png)

*Figure 72. Channel and Status Packet Data Formats with Test Pattern Output Enabled (TEST_PAT = 1)*

### SPI REGISTER CONFIGURATION BUS
<!-- page: 47 -->

The SPI register configuration bus allows the digital host to read from and write to the AD4858 memory map registers. This bus is independent of the CMOS or LVDS conversion data output buses.

On device power up or global reset, the SPI register configuration bus defaults to 3-wire operation, consisting of the CSCK pin, the CSDIO pin, and the C̅S̅ pin. The 4-wire mode can be enabled by setting the CSDO\_EN bit to 1 in the SPI\_CONFIG\_A register. The 4-wire mode SPI serial data is output on the CSDO line by default, but it can be output on the SDO0 lane by setting the CSDO\_ON\_SDO0 bit to 1 in the SPI\_CONFIG\_D register.

A basic SPI frame begins with a C̅S̅ falling edge, followed by a 16-bit instruction phase and variable-length data phase, and terminates with a C̅S̅ rising edge. Input data on the CSDIO lane is latched on the CSCK line rising edges while data is shifted out on the CSDIO lane (3-wire mode) or the CSDO line (4-wire mode) on the CSCK falling edges. Data is aligned at the MSB first for all SPI transactions.

### Instruction Phase
<!-- page: 47 -->

Every SPI frame begins with a C̅S̅ falling edge immediately followed by an instruction phase. The instruction phase consists of a read or write bit (R/W) followed by a 15-bit register address word. Set the R/W bit high to initiate a read instruction or low to initiate a write instruction, as shown in Figure 73 and Figure 74. The register address word specifies the address of the register to be accessed.

Two instruction modes are supported by the AD4858. In Streaming Instruction Mode, multiple contiguous addresses can be accessed during a variable-length data phase, which ends with a C̅S̅ rising edge. In Nonstreaming Instruction Mode, each instruction is followed by a single-byte (plus optional CRC byte) data phase, providing access to a single address per instruction. In this mode, multiple instruction and data phase pairs can be provided in a single SPI frame.

### Data Phase
<!-- page: 47 -->

During the data phase, register data is shifted out on the CSDIO line (3-wire mode) or the CSDO line (4-wire mode) on the CSCK line falling edges for register reads. Register data is latched in on the CSDIO line on the CSCK line rising edges for register writes. Register contents are updated as each complete byte is received during register writes. If SPI bus CRC checking is enabled, the registers are only updated if a valid CRC checksum byte is received following each data byte (see SPI Bus CRC Checking).

### 3-Wire SPI Operation
<!-- page: 47 -->

On device power up or after a global reset, the SPI register configuration bus defaults to 3-wire operation, consisting of the CSCK pin, the CSDIO pin, and the C̅S̅ pin. The timing diagrams shown in Figure 73 illustrate single-byte SPI read and write transactions in this mode of operation.

During write transactions, the CSDIO pin functions as a serial data input during both the instruction and data phases. During read transactions, the CSDIO pin functions as a serial data input during the instruction phase and a serial data output during the data phase. The transition from input to output occurs after the last CSCK rising edge of the instruction phase. By using the 3-wire mode, only three digital lines are required to be routed between the AD4858 and the digital host.

![Figure 73. 3-Wire SPI Register Configuration Bus Frame](ad4858/figures/ad4858-f074.png)

*Figure 73. 3-Wire SPI Register Configuration Bus Frame*

### 4-Wire SPI Operation
<!-- page: 48 -->

To enable 4-wire operation of the SPI register configuration bus, set the CSDO\_EN bit to 1 in the SPI\_CONFIG\_A register. In the 4-wire mode SPI serial data is output on the CSDO pin by default (see Figure 74), but it can be optionally output on the SDO0 pin by setting the CSDO\_ON\_SDO0 bit to 1 in the SPI\_CONFIG\_D register. The latter option reduces the number of data lines required between the AD4858 and the host controller. In 4-wire bus operation, the CSDIO pin always functions as a serial data input, and either the CSDO pin or the SDO0 pin functions as the serial data output.

![Figure 74. 4 -Wire SPI Register Configuration Bus Frame](ad4858/figures/ad4858-f075.png)

*Figure 74. 4 -Wire SPI Register Configuration Bus Frame*

### Streaming Instruction Mode
<!-- page: 49 -->

When the INST\_MODE bit in the SPI Configuration B Register section is set to 0, streaming mode is enabled. In streaming mode, only one Instruction Phase is accepted per SPI frame and is followed by multiple Data Phase, one per register being accessed.

The register address being read from or written to is automatically incremented (ADDR\_DIR bit high) or decremented (ADDR\_DIR bit low) after each data phase. Streaming mode enables efficient access to large, contiguous register addresses of the AD4858 memory map and is enabled by default.

If the ascending address option is selected, the address increments automatically a number of times defined by LOOP\_SIZE in the Loop Configuration A Register. If the address reaches 0xB9, it then continues from Address 0x00 on the subsequent byte access.

If the descending address option is selected, the address decrements automatically a number of times defined by LOOP\_SIZE in the Loop Configuration A Register. If the address reaches 0x00, it then continues from Address 0xB9 on the subsequent byte access.

By default, the LOOP\_SIZE bit resets to 0 at every rising edge of the C̅S̅ pin; therefore, a user-set value only persists for one SPI frame. If persistent looping is required, set KEEP\_LOOP\_SIZE bit to 1.

There is only one instruction phase per frame in streaming mode, so all SPI transactions in a given SPI frame are either all reads or all writes.

### Nonstreaming Instruction Mode
<!-- page: 49 -->

When the INST\_MODE bit in the SPI\_CONFIG\_B register is set to 1, nonstreaming instruction mode is selected. In nonstreaming instruction mode, one or more SPI transactions can be provided in a single SPI frame. Each transaction includes an instruction phase to specify whether a read or write is being performed and which address is being accessed. Nonstreaming instruction mode allows the digital host to quickly read from and write to registers with nonadjacent register addresses in a single SPI frame-as opposed to streaming mode, which allows exclusively reading from or writing to registers with adjacent addresses in an SPI frame.

### SPI Bus CRC Checking
<!-- page: 49 -->

The AD4858 register bus data includes optional error checking based on an 8-bit CRC. When the CRC is enabled, an 8-bit checksum code is appended to the data phase of the read or write transaction for each register. The value of the checksum is calculated from the data read or written, allowing the AD4858 and the digital host to detect if data corruption has occurred. If the checksum does not match the corresponding register data, the register read or write is considered invalid.

The following CRC polynomial is used to calculate the checksums: 

$$x^{8}+x^{2}+x^{3}+x+1$$

The initial value for the CRC calculation is 0xA5 in all transactions.

The AD4858 has programmable user registers that are used to configure the device and monitor its state. These registers can be accessed using the SPI Register Configuration Bus. The Register Summary gives an overview of the full AD4858 register map and the bit fields contained in each single-byte register. Any register address that is not specified in this table is reserved. The Register Details section describes each register in more detail. The register details for Channel 0 are described, but the descriptions apply to all subsequent channel registers, Channel 1 through Channel 7. The reset state shows the default state of registers and bit fields after device reset. The access mode specifies whether bits are read-only (R), read or write (R/W), or read or write-one-to-clear (R/W1C).

### REGISTER SUMMARY
<!-- pages: 50-54 -->

**Table 20. Register Summary** ([table-19-p50-register.csv](ad4858/tables/table-19-p50-register.csv), p. 50)

| Addr | Name | Bits | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 | Reset | R/W |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 0x00 | SPI_CONFIG_A | [7:0] | SW_RST_MSB | RESERVED | ADDR_DIR | CSDO_EN | RESERVED | RESERVED | RESERVED | SW_RST_LSB | 0x00 | R/W |
| 0x01 | SPI_CONFIG_B | [7:0] | INST_MODE | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x02 | DEVICE_CONFIG | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | PWR_MODE | PWR_MODE | 0xF0 | R/W |
| 0x03 | DEVICE_TYPE | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | DEVICE_TYPE | DEVICE_TYPE | DEVICE_TYPE | DEVICE_TYPE | 0x07 | R |
| 0x04 | PRODUCT_ID_L | [7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | PRODUCT_ID[7:0] | 0x60 | R |
| 0x05 | PRODUCT_ID_H | [7:0] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | PRODUCT_ID[15:8] | 0x00 | R |
| 0x06 | DEVICE_GRADE | [7:0] | DEVICE_GRADE | DEVICE_GRADE | DEVICE_GRADE | DEVICE_GRADE | DEVICE_REVISION | DEVICE_REVISION | DEVICE_REVISION | DEVICE_REVISION | 0x00 | R |
| 0x0A | SCRATCH_PAD | [7:0] | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | SCRATCH_VALUE | 0x00 | R/W |
| 0x0B | SPI_REVISION | [7:0] | SPI_TYPE | SPI_TYPE | VERSION | VERSION | VERSION | VERSION | VERSION | VERSION | 0x83 | R |
| 0x0C | VENDOR_ID_L | [7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | VENDOR_ID[7:0] | 0x56 | R |
| 0x0D | VENDOR_ID_H | [7:0] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | VENDOR_ID[15:8] | 0x04 | R |
| 0x0E | LOOP_CONFIG_A | [7:0] | LOOP_SIZE | LOOP_SIZE | LOOP_SIZE | LOOP_SIZE | LOOP_SIZE | LOOP_SIZE | LOOP_SIZE | LOOP_SIZE | 0x00 | R/W |
| 0x0F | LOOP_CONFIG_B | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | KEEP_LOOP_SIZE | RESERVED | RESERVED | 0x00 | R/W |
| 0x10 | SPI_CONFIG_C | [7:0] | CRC_ENABLE | CRC_ENABLE | RESERVED | RESERVED | RESERVED | RESERVED | CRC_ENABLE_N | CRC_ENABLE_N | 0x03 | R/W |
| 0x11 | SPI_STATUS | [7:0] | NOT_RDY_ERR | RESERVED | RESERVED | CLK_COUNT_ERR | CRC_ERR | WRITE_INVALID | RESERVED | ADDR_INVALID | 0x00 | R/W |
| 0x14 | SPI_CONFIG_D | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | CSDO_ON_SDO0 | 0x00 | R/W |
| 0x20 | DEVICE_STATUS | [7:0] | DEVICE_READY_FLAG | RESET_FLAG | FUSE_CRC_FLAG | REGMAP_CRC_FLAG | SPI_FLAG | CH_ORUR_FLAG | PD_FLAG | SLEEP_FLAG | 0x40 | R/W |
| 0x21 | CH_OR_STATUS | [7:0] | CH7_OR_FLAG | CH6_OR_FLAG | CH5_OR_FLAG | CH4_OR_FLAG | CH3_OR_FLAG | CH2_OR_FLAG | CH1_OR_FLAG | CH0_OR_FLAG | 0x00 | R/W |
| 0x22 | CH_UR_STATUS | [7:0] | CH7_UR_FLAG | CH6_UR_FLAG | CH5_UR_FLAG | CH4_UR_FLAG | CH3_UR_FLAG | CH2_UR_FLAG | CH1_UR_FLAG | CH0_UR_FLAG | 0x00 | R/W |
| 0x23 | REGMAP_CRC | [7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | REGMAP_CRC[7:0] | 0x00 | R/W |
| 0x24 | REGMAP_CRC | [15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | REGMAP_CRC[15:8] | 0x00 | R/W |
| 0x25 | DEVICE_CTRL | [7:0] | TEST_CRCS | RESERVED | RESERVED | LVDS_TERM | LVDS_HALF_BIAS | REFBUF_PD | REF_SEL | SCKO_ECHO | 0x11 | R/W |
| 0x26 | PACKET | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | RESERVED | TEST_PAT | PACKET_SIZE | PACKET_SIZE | 0x01 | R/W |
| 0x27 | OVERSAMPLE | [7:0] | OS_EN | RESERVED | RESERVED | RESERVED | OS_RATIO | OS_RATIO | OS_RATIO | OS_RATIO | 0x00 | R/W |
| 0x28 | SEAMLESS_HDR | [7:0] | CH7_SHDR_EN | CH6_SHDR_EN | CH5_SHDR_EN | CH4_SHDR_EN | CH3_SHDR_EN | CH2_SHDR_EN | CH1_SHDR_EN | CH0_SHDR_EN | 0xFF | R/W |
| 0x29 | CH_SLEEP | [7:0] | CH7_SLEEP | CH6_SLEEP | CH5_SLEEP | CH4_SLEEP | CH3_SLEEP | CH2_SLEEP | CH1_SLEEP | CH0_SLEEP | 0x00 | R/W |
| 0x2A | CH0_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH0_SOFTSPAN | CH0_SOFTSPAN | CH0_SOFTSPAN | CH0_SOFTSPAN | 0x0F | R/W |
| 0x2B | CH0_OFFSET | [7:0] | CH0_OFFSET[3:0] | CH0_OFFSET[3:0] | CH0_OFFSET[3:0] | CH0_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x2C | CH0_OFFSET | [15:8] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | CH0_OFFSET[11:4] | 0x00 | R/W |
| 0x2D | CH0_OFFSET | [23:16] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | CH0_OFFSET[19:12] | 0x00 | R/W |
| 0x2E | CH0_GAIN | [7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | CH0_GAIN[7:0] | 0x00 | R/W |
| 0x2F | CH0_GAIN | [15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | CH0_GAIN[15:8] | 0x80 | R/W |
| 0x30 | CH0_PHASE | [7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | CH0_PHASE[7:0] | 0x00 | R/W |
| 0x31 | CH0_PHASE | [15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | CH0_PHASE[15:8] | 0x00 | R/W |
| 0x32 | CH0_OR | [7:0] | CH0_OR[3:0] | CH0_OR[3:0] | CH0_OR[3:0] | CH0_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x33 | CH0_OR | [15:8] | CH0_OR[11:4] | CH0_OR[11:4] | CH0_OR[11:4] | CH0_OR[11:4] | CH0_OR[11:4] | CH0_OR[11:4] | CH0_OR[11:4] | CH0_OR[11:4] | 0xFF | R/W |
| 0x34 | CH0_OR | [23:16] | CH0_OR[19:12] | CH0_OR[19:12] | CH0_OR[19:12] | CH0_OR[19:12] | CH0_OR[19:12] | CH0_OR[19:12] | CH0_OR[19:12] | CH0_OR[19:12] | 0x7F | R/W |
| 0x35 | CH0_UR | [7:0] | CH0_UR[3:0] | CH0_UR[3:0] | CH0_UR[3:0] | CH0_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x36 | CH0_UR | [15:8] | CH0_UR[11:4] | CH0_UR[11:4] | CH0_UR[11:4] | CH0_UR[11:4] | CH0_UR[11:4] | CH0_UR[11:4] | CH0_UR[11:4] | CH0_UR[11:4] | 0x00 | R/W |
| 0x37 | CH0_UR | [23:16] | CH0_UR[19:12] | CH0_UR[19:12] | CH0_UR[19:12] | CH0_UR[19:12] | CH0_UR[19:12] | CH0_UR[19:12] | CH0_UR[19:12] | CH0_UR[19:12] | 0x80 | R/W |
| 0x38 | CH0_TESTPAT | [7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | CH0_TESTPAT[7:0] | 0x2A | R/W |
| 0x39 | CH0_TESTPAT | [15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | CH0_TESTPAT[15:8] | 0x3C | R/W |
| 0x3A | CH0_TESTPAT | [23:16] | CH0_TESTPAT[23:16] | CH0_TESTPAT[23:16] | CH0_TESTPAT[23:16] | CH0_TESTPAT[23:16] | CH0_TESTPAT[23:16] | CH0_TESTPAT[23:16] |CH0_TESTPAT[23:16]  | CH0_TESTPAT[23:16] | 0xCE | R/W |
| 0x3B | CH0_TESTPAT | [31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | CH0_TESTPAT[31:24] | 0x0A | R/W |
| 0x3C | CH1_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH1_SOFTSPAN | CH1_SOFTSPAN | CH1_SOFTSPAN | CH1_SOFTSPAN | 0x0F | R/W |
| 0x3D | CH1_OFFSET | [7:0] | CH1_OFFSET[3:0] | CH1_OFFSET[3:0] | CH1_OFFSET[3:0] | CH1_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x3E | CH1_OFFSET | [15:8] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | CH1_OFFSET[11:4] | 0x00 | R/W |
| 0x3F | CH1_OFFSET | [23:16] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | CH1_OFFSET[19:12] | 0x00 | R/W |
| 0x40 | CH1_GAIN | [7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | CH1_GAIN[7:0] | 0x00 | R/W |
| 0x41 | CH1_GAIN | [15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | CH1_GAIN[15:8] | 0x80 | R/W |
| 0x42 | CH1_PHASE | [7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | CH1_PHASE[7:0] | 0x00 | R/W |
| 0x43 | CH1_PHASE | [15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | CH1_PHASE[15:8] | 0x00 | R/W |
| 0x44 | CH1_OR | [7:0] | CH1_OR[3:0] | CH1_OR[3:0] | CH1_OR[3:0] | CH1_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x45 | CH1_OR | [15:8] | CH1_OR[11:4] | CH1_OR[11:4] | CH1_OR[11:4] | CH1_OR[11:4] | CH1_OR[11:4] | CH1_OR[11:4] | CH1_OR[11:4] | CH1_OR[11:4] | 0xFF | R/W |
| 0x46 | CH1_OR | [23:16] | CH1_OR[19:12] | CH1_OR[19:12] | CH1_OR[19:12] | CH1_OR[19:12] | CH1_OR[19:12] | CH1_OR[19:12] | CH1_OR[19:12] | CH1_OR[19:12] | 0x7F | R/W |
| 0x47 | CH1_UR | [7:0] | CH1_UR[3:0] | CH1_UR[3:0] | CH1_UR[3:0] | CH1_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x48 | CH1_UR | [15:8] | CH1_UR[11:4] | CH1_UR[11:4] | CH1_UR[11:4] | CH1_UR[11:4] | CH1_UR[11:4] | CH1_UR[11:4] | CH1_UR[11:4] | CH1_UR[11:4] | 0x00 | R/W |
| 0x49 | CH1_UR | [23:16] | CH1_UR[19:12] | CH1_UR[19:12] | CH1_UR[19:12] | CH1_UR[19:12] | CH1_UR[19:12] | CH1_UR[19:12] | CH1_UR[19:12] | CH1_UR[19:12] | 0x80 | R/W |
| 0x4A | CH1_TESTPAT | [7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | CH1_TESTPAT[7:0] | 0x2A | R/W |
| 0x4B | CH1_TESTPAT | [15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | CH1_TESTPAT[15:8] | 0x3C | R/W |
| 0x4C | CH1_TESTPAT | [23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | CH1_TESTPAT[23:16] | 0xCE | R/W |
| 0x4D | CH1_TESTPAT | [31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | CH1_TESTPAT[31:24] | 0x1A | R/W |
| 0x4E | CH2_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH2_SOFTSPAN | CH2_SOFTSPAN | CH2_SOFTSPAN | CH2_SOFTSPAN | 0x0F | R/W |
| 0x4F | CH2_OFFSET | [7:0] | CH2_OFFSET[3:0] | CH2_OFFSET[3:0] | CH2_OFFSET[3:0] | CH2_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x50 | CH2_OFFSET | [15:8] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | CH2_OFFSET[11:4] | 0x00 | R/W |
| 0x51 | CH2_OFFSET | [23:16] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | CH2_OFFSET[19:12] | 0x00 | R/W |
| 0x52 | CH2_GAIN | [7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | CH2_GAIN[7:0] | 0x00 | R/W |
| 0x53 | CH2_GAIN | [15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | CH2_GAIN[15:8] | 0x80 | R/W |
| 0x54 | CH2_PHASE | [7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | CH2_PHASE[7:0] | 0x00 | R/W |
| 0x55 | CH2_PHASE | [15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | CH2_PHASE[15:8] | 0x00 | R/W |
| 0x56 | CH2_OR | [7:0] | CH2_OR[3:0] | CH2_OR[3:0] | CH2_OR[3:0] | CH2_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x57 | CH2_OR | [15:8] | CH2_OR[11:4] | CH2_OR[11:4] | CH2_OR[11:4] | CH2_OR[11:4] | CH2_OR[11:4] | CH2_OR[11:4] | CH2_OR[11:4] | CH2_OR[11:4] | 0xFF | R/W |
| 0x58 | CH2_OR | [23:16] | CH2_OR[19:12] | CH2_OR[19:12] | CH2_OR[19:12] | CH2_OR[19:12] | CH2_OR[19:12] | CH2_OR[19:12] | CH2_OR[19:12] | CH2_OR[19:12] | 0x7F | R/W |
| 0x59 | CH2_UR | [7:0] | CH2_UR[3:0] | CH2_UR[3:0] | CH2_UR[3:0] | CH2_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x5A | CH2_UR | [15:8] | CH2_UR[11:4] | CH2_UR[11:4] | CH2_UR[11:4] | CH2_UR[11:4] | CH2_UR[11:4] | CH2_UR[11:4] | CH2_UR[11:4] | CH2_UR[11:4] | 0x00 | R/W |
| 0x5B | CH2_UR | [23:16] | CH2_UR[19:12] | CH2_UR[19:12] | CH2_UR[19:12] | CH2_UR[19:12] | CH2_UR[19:12] | CH2_UR[19:12] | CH2_UR[19:12] | CH2_UR[19:12] | 0x80 | R/W |
| 0x5C | CH2_TESTPAT | [7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | CH2_TESTPAT[7:0] | 0x2A | R/W |
| 0x5D | CH2_TESTPAT | [15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | CH2_TESTPAT[15:8] | 0x3C | R/W |
| 0x5E | CH2_TESTPAT | [23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | CH2_TESTPAT[23:16] | 0xCE | R/W |
| 0x5F | CH2_TESTPAT | [31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | CH2_TESTPAT[31:24] | 0x2A | R/W |
| 0x60 | CH3_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH3_SOFTSPAN | CH3_SOFTSPAN | CH3_SOFTSPAN | CH3_SOFTSPAN | 0x0F | R/W |
| 0x61 | CH3_OFFSET | [7:0] | CH3_OFFSET[3:0] | CH3_OFFSET[3:0] | CH3_OFFSET[3:0] | CH3_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x62 | CH3_OFFSET | [15:8] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | CH3_OFFSET[11:4] | 0x00 | R/W |
| 0x63 | CH3_OFFSET | [23:16] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | CH3_OFFSET[19:12] | 0x00 | R/W |
| 0x64 | CH3_GAIN | [7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | CH3_GAIN[7:0] | 0x00 | R/W |
| 0x65 | CH3_GAIN | [15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | CH3_GAIN[15:8] | 0x80 | R/W |
| 0x66 | CH3_PHASE | [7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | CH3_PHASE[7:0] | 0x00 | R/W |
| 0x67 | CH3_PHASE | [15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | CH3_PHASE[15:8] | 0x00 | R/W |
| 0x68 | CH3_OR | [7:0] | CH3_OR[3:0] | CH3_OR[3:0] | CH3_OR[3:0] | CH3_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x69 | CH3_OR | [15:8] | CH3_OR[11:4] | CH3_OR[11:4] | CH3_OR[11:4] | CH3_OR[11:4] | CH3_OR[11:4] | CH3_OR[11:4] | CH3_OR[11:4] | CH3_OR[11:4] | 0xFF | R/W |
| 0x6A | CH3_OR | [23:16] | CH3_OR[19:12] | CH3_OR[19:12] | CH3_OR[19:12] | CH3_OR[19:12] | CH3_OR[19:12] | CH3_OR[19:12] | CH3_OR[19:12] | CH3_OR[19:12] | 0x7F | R/W |
| 0x6B | CH3_UR | [7:0] | CH3_UR[3:0] | CH3_UR[3:0] | CH3_UR[3:0] | CH3_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x6C | CH3_UR | [15:8] | CH3_UR[11:4] | CH3_UR[11:4] | CH3_UR[11:4] | CH3_UR[11:4] | CH3_UR[11:4] | CH3_UR[11:4] | CH3_UR[11:4] | CH3_UR[11:4] | 0x00 | R/W |
| 0x6D | CH3_UR | [23:16] | CH3_UR[19:12] | CH3_UR[19:12] | CH3_UR[19:12] | CH3_UR[19:12] | CH3_UR[19:12] | CH3_UR[19:12] | CH3_UR[19:12] | CH3_UR[19:12] | 0x80 | R/W |
| 0x6E | CH3_TESTPAT | [7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | CH3_TESTPAT[7:0] | 0x2A | R/W |
| 0x6F | CH3_TESTPAT | [15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | CH3_TESTPAT[15:8] | 0x3C | R/W |
| 0x70 | CH3_TESTPAT | [23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | CH3_TESTPAT[23:16] | 0xCE | R/W |
| 0x71 | CH3_TESTPAT | [31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | CH3_TESTPAT[31:24] | 0x3A | R/W |
| 0x72 | CH4_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH4_SOFTSPAN | CH4_SOFTSPAN | CH4_SOFTSPAN | CH4_SOFTSPAN | 0x0F | R/W |
| 0x73 | CH4_OFFSET | [7:0] | CH4_OFFSET[3:0] | CH4_OFFSET[3:0] | CH4_OFFSET[3:0] | CH4_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x74 | CH4_OFFSET | [15:8] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | CH4_OFFSET[11:4] | 0x00 | R/W |
| 0x75 | CH4_OFFSET | [23:16] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | CH4_OFFSET[19:12] | 0x00 | R/W |
| 0x76 | CH4_GAIN | [7:0] | CH4_GAIN[7:0] | CH4_GAIN[7:0] | CH4_GAIN[7:0] |CH4_GAIN[7:0]  | CH4_GAIN[7:0] | CH4_GAIN[7:0] | CH4_GAIN[7:0] | CH4_GAIN[7:0] | 0x00 | R/W |
| 0x77 | CH4_GAIN | [15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | CH4_GAIN[15:8] | 0x80 | R/W |
| 0x78 | CH4_PHASE | [7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | CH4_PHASE[7:0] | 0x00 | R/W |
| 0x79 | CH4_PHASE | [15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | CH4_PHASE[15:8] | 0x00 | R/W |
| 0x7A | CH4_OR | [7:0] | CH4_OR[3:0] | CH4_OR[3:0] | CH4_OR[3:0] | CH4_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x7B | CH4_OR | [15:8] | CH4_OR[11:4] | CH4_OR[11:4] | CH4_OR[11:4] | CH4_OR[11:4] | CH4_OR[11:4] | CH4_OR[11:4] | CH4_OR[11:4] | CH4_OR[11:4] | 0xFF | R/W |
| 0x7C | CH4_OR | [23:16] | CH4_OR[19:12] | CH4_OR[19:12] | CH4_OR[19:12] | CH4_OR[19:12] | CH4_OR[19:12] | CH4_OR[19:12] | CH4_OR[19:12] | CH4_OR[19:12] | 0x7F | R/W |
| 0x7D | CH4_UR | [7:0] | CH4_UR[3:0] | CH4_UR[3:0] | CH4_UR[3:0] | CH4_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x7E | CH4_UR | [15:8] | CH4_UR[11:4] | CH4_UR[11:4] | CH4_UR[11:4] | CH4_UR[11:4] | CH4_UR[11:4] | CH4_UR[11:4] | CH4_UR[11:4] | CH4_UR[11:4] | 0x00 | R/W |
| 0x7F | CH4_UR | [23:16] | CH4_UR[19:12] | CH4_UR[19:12] | CH4_UR[19:12] | CH4_UR[19:12] | CH4_UR[19:12] | CH4_UR[19:12] | CH4_UR[19:12] | CH4_UR[19:12] | 0x80 | R/W |
| 0x80 | CH4_TESTPAT | [7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | CH4_TESTPAT[7:0] | 0x2A | R/W |
| 0x81 | CH4_TESTPAT | [15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | CH4_TESTPAT[15:8] | 0x3C | R/W |
| 0x82 | CH4_TESTPAT | [23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | CH4_TESTPAT[23:16] | 0xCE | R/W |
| 0x83 | CH4_TESTPAT | [31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | CH4_TESTPAT[31:24] | 0x4A | R/W |
| 0x84 | CH5_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH5_SOFTSPAN | CH5_SOFTSPAN | CH5_SOFTSPAN | CH5_SOFTSPAN | 0x0F | R/W |
| 0x85 | CH5_OFFSET | [7:0] | CH5_OFFSET[3:0] | CH5_OFFSET[3:0] | CH5_OFFSET[3:0] | CH5_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x86 | CH5_OFFSET | [15:8] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | CH5_OFFSET[11:4] | 0x00 | R/W |
| 0x87 | CH5_OFFSET | [23:16] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | CH5_OFFSET[19:12] | 0x00 | R/W |
| 0x88 | CH5_GAIN | [7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | CH5_GAIN[7:0] | 0x00 | R/W |
| 0x89 | CH5_GAIN | [15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | CH5_GAIN[15:8] | 0x80 | R/W |
| 0x8A | CH5_PHASE | [7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | CH5_PHASE[7:0] | 0x00 | R/W |
| 0x8B | CH5_PHASE | [15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | CH5_PHASE[15:8] | 0x00 | R/W |
| 0x8C | CH5_OR | [7:0] | CH5_OR[3:0] | CH5_OR[3:0] | CH5_OR[3:0] | CH5_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x8D | CH5_OR | [15:8] | CH5_OR[11:4] | CH5_OR[11:4] | CH5_OR[11:4] | CH5_OR[11:4] | CH5_OR[11:4] | CH5_OR[11:4] | CH5_OR[11:4] | CH5_OR[11:4] | 0xFF | R/W |
| 0x8E | CH5_OR | [23:16] | CH5_OR[19:12] | CH5_OR[19:12] | CH5_OR[19:12] | CH5_OR[19:12] | CH5_OR[19:12] | CH5_OR[19:12] | CH5_OR[19:12] | CH5_OR[19:12] | 0x7F | R/W |
| 0x8F | CH5_UR | [7:0] | CH5_UR[3:0] | CH5_UR[3:0] | CH5_UR[3:0] | CH5_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x90 | CH5_UR | [15:8] | CH5_UR[11:4] | CH5_UR[11:4] | CH5_UR[11:4] | CH5_UR[11:4] | CH5_UR[11:4] | CH5_UR[11:4] | CH5_UR[11:4] | CH5_UR[11:4] | 0x00 | R/W |
| 0x91 | CH5_UR | [23:16] | CH5_UR[19:12] | CH5_UR[19:12] | CH5_UR[19:12] | CH5_UR[19:12] | CH5_UR[19:12] | CH5_UR[19:12] | CH5_UR[19:12] | CH5_UR[19:12] | 0x80 | R/W |
| 0x92 | CH5_TESTPAT | [7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | CH5_TESTPAT[7:0] | 0x2A | R/W |
| 0x93 | CH5_TESTPAT | [15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | CH5_TESTPAT[15:8] | 0x3C | R/W |
| 0x94 | CH5_TESTPAT | [23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | CH5_TESTPAT[23:16] | 0xCE | R/W |
| 0x95 | CH5_TESTPAT | [31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | CH5_TESTPAT[31:24] | 0x5A | R/W |
| 0x96 | CH6_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH6_SOFTSPAN | CH6_SOFTSPAN | CH6_SOFTSPAN | CH6_SOFTSPAN | 0x0F | R/W |
| 0x97 | CH6_OFFSET | [7:0] | CH6_OFFSET[3:0] | CH6_OFFSET[3:0] | CH6_OFFSET[3:0] | CH6_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0x98 | CH6_OFFSET | [15:8] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | CH6_OFFSET[11:4] | 0x00 | R/W |
| 0x99 | CH6_OFFSET | [23:16] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | CH6_OFFSET[19:12] | 0x00 | R/W |
| 0x9A | CH6_GAIN | [7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | CH6_GAIN[7:0] | 0x00 | R/W |
| 0x9B | CH6_GAIN | [15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | CH6_GAIN[15:8] | 0x80 | R/W |
| 0x9C | CH6_PHASE | [7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | CH6_PHASE[7:0] | 0x00 | R/W |
| 0x9D | CH6_PHASE | [15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | CH6_PHASE[15:8] | 0x00 | R/W |
| 0x9E | CH6_OR | [7:0] | CH6_OR[3:0] | CH6_OR[3:0] | CH6_OR[3:0] | CH6_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0x9F | CH6_OR | [15:8] | CH6_OR[11:4] | CH6_OR[11:4] | CH6_OR[11:4] | CH6_OR[11:4] | CH6_OR[11:4] | CH6_OR[11:4] | CH6_OR[11:4] | CH6_OR[11:4] | 0xFF | R/W |
| 0xA0 | CH6_OR | [23:16] | CH6_OR[19:12] | CH6_OR[19:12] | CH6_OR[19:12] | CH6_OR[19:12] | CH6_OR[19:12] | CH6_OR[19:12] | CH6_OR[19:12] | CH6_OR[19:12] | 0x7F | R/W |
| 0xA1 | CH6_UR | [7:0] | CH6_UR[3:0] | CH6_UR[3:0] | CH6_UR[3:0] | CH6_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0xA2 | CH6_UR | [15:8] | CH6_UR[11:4] | CH6_UR[11:4] | CH6_UR[11:4] | CH6_UR[11:4] | CH6_UR[11:4] | CH6_UR[11:4] | CH6_UR[11:4] | CH6_UR[11:4] | 0x00 | R/W |
| 0xA3 | CH6_UR | [23:16] | CH6_UR[19:12] | CH6_UR[19:12] | CH6_UR[19:12] | CH6_UR[19:12] | CH6_UR[19:12] | CH6_UR[19:12] | CH6_UR[19:12] | CH6_UR[19:12] | 0x80 | R/W |
| 0xA4 | CH6_TESTPAT | [7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | CH6_TESTPAT[7:0] | 0x2A | R/W |
| 0xA5 | CH6_TESTPAT | [15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | CH6_TESTPAT[15:8] | 0x3C | R/W |
| 0xA6 | CH6_TESTPAT | [23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | CH6_TESTPAT[23:16] | 0xCE | R/W |
| 0xA7 | CH6_TESTPAT | [31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | CH6_TESTPAT[31:24] | 0x6A | R/W |
| 0xA8 | CH7_SOFTSPAN | [7:0] | RESERVED | RESERVED | RESERVED | RESERVED | CH7_SOFTSPAN | CH7_SOFTSPAN | CH7_SOFTSPAN | CH7_SOFTSPAN | 0x0F | R/W |
| 0xA9 | CH7_OFFSET | [7:0] | CH7_OFFSET[3:0] | CH7_OFFSET[3:0] | CH7_OFFSET[3:0] | CH7_OFFSET[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0xAA | CH7_OFFSET | [15:8] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | CH7_OFFSET[11:4] | 0x00 | R/W |
| 0xAB | CH7_OFFSET | [23:16] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | CH7_OFFSET[19:12] | 0x00 | R/W |
| 0xAC | CH7_GAIN | [7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | CH7_GAIN[7:0] | 0x00 | R/W |
| 0xAD | CH7_GAIN | [15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | CH7_GAIN[15:8] | 0x80 | R/W |
| 0xAE | CH7_PHASE | [7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | CH7_PHASE[7:0] | 0x00 | R/W |
| 0xAF | CH7_PHASE | [15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | CH7_PHASE[15:8] | 0x00 | R/W |
| 0xB0 | CH7_OR | [7:0] | CH7_OR[3:0] | CH7_OR[3:0] | CH7_OR[3:0] | CH7_OR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0xF0 | R/W |
| 0xB1 | CH7_OR | [15:8] | CH7_OR[11:4] | CH7_OR[11:4] | CH7_OR[11:4] | CH7_OR[11:4] | CH7_OR[11:4] | CH7_OR[11:4] | CH7_OR[11:4] | CH7_OR[11:4] | 0xFF | R/W |
| 0xB2 | CH7_OR | [23:16] | CH7_OR[19:12] | CH7_OR[19:12] | CH7_OR[19:12] | CH7_OR[19:12] | CH7_OR[19:12] | CH7_OR[19:12] | CH7_OR[19:12] | CH7_OR[19:12] | 0x7F | R/W |
| 0xB3 | CH7_UR | [7:0] | CH7_UR[3:0] | CH7_UR[3:0] | CH7_UR[3:0] | CH7_UR[3:0] | RESERVED | RESERVED | RESERVED | RESERVED | 0x00 | R/W |
| 0xB4 | CH7_UR | [15:8] | CH7_UR[11:4] | CH7_UR[11:4] | CH7_UR[11:4] | CH7_UR[11:4] | CH7_UR[11:4] | CH7_UR[11:4] | CH7_UR[11:4] | CH7_UR[11:4] | 0x00 | R/W |
| 0xB5 | CH7_UR | [23:16] | CH7_UR[19:12] | CH7_UR[19:12] | CH7_UR[19:12] | CH7_UR[19:12] | CH7_UR[19:12] | CH7_UR[19:12] | CH7_UR[19:12] | CH7_UR[19:12] | 0x80 | R/W |
| 0xB6 | CH7_TESTPAT | [7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | CH7_TESTPAT[7:0] | 0x2A | R/W |
| 0xB7 | CH7_TESTPAT | [15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | CH7_TESTPAT[15:8] | 0x3C | R/W |
| 0xB8 | CH7_TESTPAT | [23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | CH7_TESTPAT[23:16] | 0xCE | R/W |
| 0xB9 | CH7_TESTPAT | [31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | CH7_TESTPAT[31:24] | 0x7A | R/W |

*Table 20 continues on the next page in the source; all rows are in the table above.*

### REGISTER DETAILS
<!-- pages: 54-70 -->

### SPI CONFIGURATION A REGISTER
<!-- page: 54 -->

![Figure 75. Address: 0x00, Reset: 0x00, Name: SPI_CONFIG_A](ad4858/figures/ad4858-f076.png)

*Figure 75. Address: 0x00, Reset: 0x00, Name: SPI_CONFIG_A*

**Table 21. Bit Descriptions for SPI_CONFIG_A** ([table-20-p54-register.csv](ad4858/tables/table-20-p54-register.csv), p. 54)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | SW_RST_MSB | Software Reset (MSB). Setting both SW_RST_MSB and SW_RST_LSB to 1 using a single register write initiates a software reset of the AD4858. This resets all registers to their default states, except for the ADDR_DIR and CSDO_EN bits in the SPI_CONFIG_A register . | 0x0 | R/W |
| 6 | RESERVED | Reserved. | 0x0 | R |
| 5 | ADDR_DIR | Address Direction. Selects between descending or ascending register addressing during multi-byte read or write transactions on the SPI Register Configuration Bus (see Streaming Instruction Mode). 0: Descending Addressing. Register address decremented by one for each data byte. 1: Ascending Addressing. Register address incremented by one for each data byte. | 0x0 | R/W |
| 4 | CSDO_EN | CSDO Pin Enable. Selects between 3-wire or 4-wire operation of the SPI register configuration bus (see the 3-Wire SPI Operation and 4-Wire SPI Operation). 0: CSDO Disabled. SPI bus operates in 3-wire mode with data input and output on CSDIO. CSDO is not used and remains high-Z. 1: CSDO Enabled. SPI bus operates in 4-wire mode with data input on CSDIO and data output on CSDO (or SDO0 if CSDO_ON_SDO0 in SPI_CONFIG_D register is set to 1). | 0x0 | R/W |
| [3:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | SW_RST_LSB | Software Reset (LSB). Setting both SW_RST_MSB and SW_RST_LSB to 1 using a single register write initiates a software reset of the AD4858. This resets all registers to their default states, except for the ADDR_DIR and CSDO_EN bits in the SPI_CONFIG_A register. | 0x0 | R/W |

- **Note 0:** Descending Addressing. Register address decremented by one for each data byte.

### SPI CONFIGURATION B REGISTER
<!-- page: 55 -->

![Figure 76. Address: 0x01, Reset: 0x00, Name: SPI_CONFIG_B](ad4858/figures/ad4858-f077.png)

*Figure 76. Address: 0x01, Reset: 0x00, Name: SPI_CONFIG_B*

**Table 22. Bit Descriptions for SPI_CONFIG_B** ([table-21-p55-register.csv](ad4858/tables/table-21-p55-register.csv), p. 55)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | INST_MODE | Instruction Mode. Selects between streaming and non-streaming instruction modes of the SPI Register Configuration Bus (see Streaming Instruction Mode and Nonstreaming Instruction Mode). 0: Streaming Instruction Mode. SPI bus accepts multi-byte read or write transactions. Register address is automatically updated for each successive data byte based on ADDR_DIR bit in SPI_CONFIG_A register . 1: Nonstreaming Instruction Mode. SPI bus accepts single-byte read or write transactions. | 0x0 | R/W |
| [6:0] | RESERVED | Reserved. | 0x0 | R |

### DEVICE CONFIGURATION REGISTER
<!-- page: 55 -->

![Figure 77. Address: 0x02, Reset: 0xF0, Name: DEVICE_CONFIG](ad4858/figures/ad4858-f078.png)

*Figure 77. Address: 0x02, Reset: 0xF0, Name: DEVICE_CONFIG*

**Table 23. Bit Descriptions for DEVICE_CONFIG** ([table-22-p55-register.csv](ad4858/tables/table-22-p55-register.csv), p. 55)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:2] | RESERVED | Reserved. | 0x3C | R |
| [1:0] | PWR_MODE | Power Mode. Software controllable alternative to PD pin functionality. 00: Normal Operating Mode. 11: Power-Down Mode. Same effect as driving PD pin to high state. | 0x0 | R/W |

### DEVICE TYPE REGISTER
<!-- page: 55 -->

![Figure 78. Address: 0x03, Reset: 0x07, Name: DEVICE_TYPE](ad4858/figures/ad4858-f079.png)

*Figure 78. Address: 0x03, Reset: 0x07, Name: DEVICE_TYPE*

**Table 24. Bit Descriptions for DEVICE_TYPE** ([table-23-p55-register.csv](ad4858/tables/table-23-p55-register.csv), p. 55)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:4] | RESERVED | Reserved. | 0x0 | R |
| [3:0] | DEVICE_TYPE | Device Type. Identifies the AD4858 as a precision ADC product. | 0x7 | R |

- **Note 0:** Streaming Instruction Mode. SPI bus accepts multi-byte read or write transactions. Register address is automatically updated for each succes- sive data byte based on ADDR_DIR bit in SPI_CONFIG_A register .

### PRODUCT ID LOW REGISTER
<!-- page: 56 -->

![Figure 79. Address: 0x04, Reset: 0x00, Name: PRODUCT_ID_L](ad4858/figures/ad4858-f080.png)

*Figure 79. Address: 0x04, Reset: 0x00, Name: PRODUCT_ID_L*

**Table 25. Bit Descriptions for PRODUCT_ID_L** ([table-24-p56-register.csv](ad4858/tables/table-24-p56-register.csv), p. 56)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | PRODUCT_ID[7:0] | Product Identification. One byte of the AD4858 PRODUCT_ID. | 0x60 | R |

### PRODUCT ID HIGH REGISTER
<!-- page: 56 -->

![Figure 80. Address: 0x05, Reset: 0x00, Name: PRODUCT_ID_H](ad4858/figures/ad4858-f081.png)

*Figure 80. Address: 0x05, Reset: 0x00, Name: PRODUCT_ID_H*

**Table 26. Bit Descriptions for PRODUCT_ID_H** ([table-25-p56-register.csv](ad4858/tables/table-25-p56-register.csv), p. 56)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | PRODUCT_ID[15:8] | Product Identification. One byte of the AD4858 PRODUCT_ID. | 0x0 | R |

### DEVICE GRADE REGISTER
<!-- page: 56 -->

![Figure 81. Address: 0x06, Reset: 0x00, Name: DEVICE_GRADE](ad4858/figures/ad4858-f082.png)

*Figure 81. Address: 0x06, Reset: 0x00, Name: DEVICE_GRADE*

**Table 27. Bit Descriptions for DEVICE_GRADE** ([table-26-p56-register.csv](ad4858/tables/table-26-p56-register.csv), p. 56)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:4] | DEVICE_GRADE | Device Performance Grade. Identifies the AD4858 performance grade. | 0x0 | R |
| [3:0] | DEVICE_REVISION | Device Hardware Revision. Identifies the AD4858 hardware revision. | 0x0 | R |

### SCRATCH PAD REGISTER
<!-- page: 56 -->

![Figure 82. Address: 0x0A, Reset: 0x00, Name: SCRATCH_PAD](ad4858/figures/ad4858-f083.png)

*Figure 82. Address: 0x0A, Reset: 0x00, Name: SCRATCH_PAD*

### Table 28. Bit Descriptions for SCRATCH\_PAD
<!-- page: 57 -->

**Table 28. Bit Descriptions for SCRATCH_PAD** ([table-27-p57-register.csv](ad4858/tables/table-27-p57-register.csv), p. 57)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | SCRATCH_VALUE | Software Scratchpad. Software can write to and read from this location without any device side effects. Use this register to test SPI register configuration bus communication. | 0x0 | R/W |

### SPI REVISION REGISTER
<!-- page: 57 -->

![Figure 83. Address: 0x0B, Reset: 0x83, Name: SPI_REVISION](ad4858/figures/ad4858-f084.png)

*Figure 83. Address: 0x0B, Reset: 0x83, Name: SPI_REVISION*

**Table 29. Bit Descriptions for SPI_REVISION** ([table-28-p57-register.csv](ad4858/tables/table-28-p57-register.csv), p. 57)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:6] | SPI_TYPE | SPI Type. Identifies the ADI SPI type supported by the AD4858. | 0x2 | R |
| [5:0] | VERSION | SPI Version. Identifies the ADI SPI version supported by the AD4858. | 0x3 | R |

### VENDOR ID LOW REGISTER
<!-- page: 57 -->

![Figure 84. Address: 0x0C, Reset: 0x56, Name: VENDOR_ID_L](ad4858/figures/ad4858-f085.png)

*Figure 84. Address: 0x0C, Reset: 0x56, Name: VENDOR_ID_L*

**Table 30. Bit Descriptions for VENDOR_ID_L** ([table-29-p57-register.csv](ad4858/tables/table-29-p57-register.csv), p. 57)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | VENDOR_ID[7:0] | Vendor Identification. One byte of the ADI VENDOR_ID. This value is the same for all ADI precision ADCs. | 0x56 | R |

### VENDOR ID HIGH REGISTER
<!-- page: 57 -->

![Figure 85. Address: 0x0D, Reset: 0x04, Name: VENDOR_ID_H](ad4858/figures/ad4858-f086.png)

*Figure 85. Address: 0x0D, Reset: 0x04, Name: VENDOR_ID_H*

**Table 31. Bit Descriptions for VENDOR_ID_H** ([table-30-p57-register.csv](ad4858/tables/table-30-p57-register.csv), p. 57)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | VENDOR_ID[15:8] | Vendor Identification. One byte of the ADI VENDOR_ID. This value is the same for all ADI precision ADCs. | 0x4 | R |

### LOOP CONFIGURATION A REGISTER
<!-- page: 58 -->

![Figure 86. Address: 0x0E, Reset: 0x00, Name: LOOP_CONFIG_A](ad4858/figures/ad4858-f087.png)

*Figure 86. Address: 0x0E, Reset: 0x00, Name: LOOP_CONFIG_A*

**Table 32. Bit Descriptions for LOOP_CONFIG_A** ([table-31-p58-register.csv](ad4858/tables/table-31-p58-register.csv), p. 58)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:0] | LOOP_SIZE | Loop Size. When streaming instruction mode is enabled (see Streaming Instruction Mode), the value of LOOP_SIZE defines the number of data bytes to be sequentially read or written before looping back to the starting address. A maximum of 255 bytes can be repeatedly looped using this approach. The default value of 0x00 disables looping, in which case addressing wraps around the upper or lower limits of the register map. | 0x0 | R/W |

### LOOP CONFIGURATION B REGISTER
<!-- page: 58 -->

![Figure 87. Address: 0x0F, Reset: 0x00, Name: LOOP_CONFIG_B](ad4858/figures/ad4858-f088.png)

*Figure 87. Address: 0x0F, Reset: 0x00, Name: LOOP_CONFIG_B*

**Table 33. Bit Descriptions for LOOP_CONFIG_B** ([table-32-p58-register.csv](ad4858/tables/table-32-p58-register.csv), p. 58)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:3] | RESERVED | Reserved. | 0x0 | R |
| 2 | KEEP_LOOP_SIZE | Keep Loop Size. Selects between resetting or retaining the LOOP_SIZE field in the LOOP_CONFIG_A register at the completion of the current streaming SPI register configuration bus transaction. 0: Reset LOOP_SIZE to 0x00 with the rising edge of C̅S̅. 1: Do not reset LOOP_SIZE. | 0x0 | R/W |
| [1:0] | RESERVED | Reserved. | 0x0 | R |

- **Note 0:** Reset LOOP_SIZE to 0x00 with the rising edge of C̅S̅.

### SPI CONFIGURATION C REGISTER
<!-- page: 58 -->

![Figure 88. Address: 0x10, Reset: 0x03, Name: SPI_CONFIG_C](ad4858/figures/ad4858-f089.png)

*Figure 88. Address: 0x10, Reset: 0x03, Name: SPI_CONFIG_C*

### Table 34. Bit Descriptions for SPI\_CONFIG\_C
<!-- page: 59 -->

**Table 34. Bit Descriptions for SPI_CONFIG_C** ([table-33-p59-register.csv](ad4858/tables/table-33-p59-register.csv), p. 59)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:6] | CRC_ENABLE | CRC Enable. Optional CRC checking is enabled on SPI register configuration bus transactions when CRC_ENABLE = 0x1 and CRC_ENABLE_N = 0x2. Any other combination of values in these fields disables SPI CRC checking. | 0x0 | R/W |
| [5:2] | RESERVED | Reserved. | 0x0 | R |
| [1:0] | CRC_ENABLE_N | Inverted CRC Enable. Optional CRC checking is enabled on SPI register configuration bus transactions when CRC_ENABLE = 0x1 and CRC_ENABLE_N = 0x2. Any other combination of values in these fields disables SPI CRC checking. | 0x3 | R/W |

### SPI STATUS REGISTER
<!-- page: 59 -->

![Figure 89. Address: 0x11, Reset: 0x00, Name: SPI_STATUS](ad4858/figures/ad4858-f090.png)

*Figure 89. Address: 0x11, Reset: 0x00, Name: SPI_STATUS*

**Table 35. Bit Descriptions for SPI_STATUS** ([table-34-p59-register.csv](ad4858/tables/table-34-p59-register.csv), p. 59)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | NOT_RDY_ERR | Not Ready for Transaction Error. This flag is set to 1 if an SPI register configuration bus transaction is initiated before the AD4858 is ready to respond, for example, before the AD4858 power-on reset initialization sequence successfully completes. | 0x0 | R/W1C |
| [6:5] | RESERVED | Reserved. | 0x0 | R |
| 4 | CLK_COUNT_ERR | Clock Count Error. This flag is set to 1 if an SPI register configuration bus transaction presents an incorrect number of CSCK edges, for example if the SPI frame ends in the middle of a data byte. | 0x0 | R/W |
| 3 | CRC_ERR | CRC Error. This flag is set to 1 if CRC checking is enabled and the AD4858 receives a checksum that does not match its computed value. | 0x0 | R/W1C |
| 2 | WRITE_INVALID | Invalid Write Error. This flag is set to 1 if the digital host attempts to write to a register that exclusively contains read-only bits. | 0x0 | R/W1C |
| 1 | RESERVED | Reserved. | 0x0 | R |
| 0 | ADDR_INVALID | Invalid Register Address Error. This flag is set to 1 if the digital host attempts to read from or write to an undefined register address. | 0x0 | R/W1C |

Table 35. Bit Descriptions for SPI\_STATUS

### SPI CONFIGURATION D REGISTER
<!-- page: 60 -->

![Figure 90. Address: 0x14, Reset: 0x00, Name: SPI_CONFIG_D](ad4858/figures/ad4858-f091.png)

*Figure 90. Address: 0x14, Reset: 0x00, Name: SPI_CONFIG_D*


**Table 36. Bit Descriptions for SPI_CONFIG_D** ([table-35-p60-register.csv](ad4858/tables/table-35-p60-register.csv), p. 60)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:1] | RESERVED | Reserved. | 0x0 | R |
| 0 | CSDO_ON_SDO0 | Output CSDO Data on SDO0. Selects between providing 4-wire SPI register configuration bus output data on CSDO or SDO0 (see 4-Wire SPI Operation). 0: Output 4-wire SPI bus data on CSDO. 1: Output 4-wire SPI bus data on SDO0. | 0x0 | R/W |

### DEVICE STATUS REGISTER
<!-- page: 60 -->

![Figure 91. Address: 0x20, Reset: 0x40, Name: DEVICE_STATUS](ad4858/figures/ad4858-f092.png)

*Figure 91. Address: 0x20, Reset: 0x40, Name: DEVICE_STATUS*

**Table 37. Bit Descriptions for DEVICE_STATUS** ([table-36-p60-register.csv](ad4858/tables/table-36-p60-register.csv), p. 60)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | DEVICE_READY_FLAG | Device Ready Flag. The AD4858 internal state is continually monitored for potential corruption due to alpha particles, system supply glitches, etc. This flag is set to 1 upon successful completion of the power-on reset initialization sequence, at the falling edge of BUSY. A value of 0 at any time past this point indicates an error in internal device state that requires a user-initiated global reset (see the Reset Timing section). | 0x0 | R |
| 6 | RESET_FLAG | Reset Flag. This flag is set to 1 at the beginning of any reset event. | 0x1 | R/W1C |
| 5 | FUSE_CRC_FLAG | Fuse CRC Flag. The AD4858 internal state is continually monitored for potential corruption due to alpha particles, system supply glitches, etc. A value of 1 at any time in this flag indicates an error has been detected that requires a user-initiated global reset (see the Reset Timing section). | 0x0 | R/W1C |
| 4 | REGMAP_CRC_FLAG | Register Map CRC Flag. The state of the AD4858 register map is continually monitored for potential corruption due to alpha particles, system supply glitches, etc. A value of 1 at any time in this flag indicates a CRC error has been detected and the digital host | 0x0 | R/W1C |
|  |  | should check the register map for errors. Ignore this flag if the REGMAP_CRC register has not been programmed with the proper CRC code. |  |  |
| 3 | SPI_FLAG | SPI Flag. This flag is the logical OR of all bits in the SPI_STATUS register. | 0x0 | R |
| 2 | CH_ORUR_FLAG | Channel Overrange/Underrange Flag. This flag is the logical OR of all bits in the CH_OR_STATUS and CH_UR_STATUS registers. | 0x0 | R |
| 1 | PD_FLAG | Power Down Flag. This flag is set to 1 when the AD4858 is currently in Power Down mode. | 0x0 | R |
| 0 | SLEEP_FLAG | Channel Sleep Flag. This flag is the logical OR of all bits in the CH_SLEEP register. | 0x0 | R |

- **Note 0:** Output 4-wire SPI bus data on CSDO.
- **Note 1:** Output 4-wire SPI bus data on SDO0.

### CHANNEL OVERRANGE STATUS REGISTER
<!-- page: 61 -->

![Figure 92. Address: 0x21, Reset: 0x00, Name: CH_OR_STATUS](ad4858/figures/ad4858-f093.png)

*Figure 92. Address: 0x21, Reset: 0x00, Name: CH_OR_STATUS*

**Table 38. Bit Descriptions for CH_OR_STATUS** ([table-37-p61-register.csv](ad4858/tables/table-37-p61-register.csv), p. 61)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | CH7_OR_FLAG | Channel 7 Overrange Flag. This flag is set to 1 when a conversion result on Channel 7 exceeds the overrange limit set in the CH7_OR register. | 0x0 | R/W1C |
| 6 | CH6_OR_FLAG | Channel 6 Overrange Flag. This flag is set to 1 when a conversion result on Channel 6 exceeds the overrange limit set in the CH6_OR register. | 0x0 | R/W1C |
| 5 | CH5_OR_FLAG | Channel 5 Overrange Flag. This flag is set to 1 when a conversion result on Channel 5 exceeds the overrange limit set in the CH5_OR register. | 0x0 | R/W1C |
| 4 | CH4_OR_FLAG | Channel 4 Overrange Flag. This flag is set to 1 when a conversion result on Channel 4 exceeds the overrange limit set in the CH4_OR register. | 0x0 | R/W1C |
| 3 | CH3_OR_FLAG | Channel 3 Overrange Flag. This flag is set to 1 when a conversion result on Channel 3 exceeds the overrange limit set in the CH3_OR register. | 0x0 | R/W1C |
| 2 | CH2_OR_FLAG | Channel 2 Overrange Flag. This flag is set to 1 when a conversion result on Channel 2 exceeds the overrange limit set in the CH2_OR register. | 0x0 | R/W1C |
| 1 | CH1_OR_FLAG | Channel 1 Overrange Flag. This flag is set to 1 when a conversion result on Channel 1 exceeds the overrange limit set in the CH1_OR register. | 0x0 | R/W1C |
| 0 | CH0_OR_FLAG | Channel 0 Overrange Flag. This flag is set to 1 when a conversion result on Channel 0 exceeds the overrange limit set in the CH0_OR register. | 0x0 | R/W1C |

Table 38. Bit Descriptions for CH\_OR\_STATUS

### CHANNEL UNDERRANGE STATUS REGISTER
<!-- page: 62 -->

![Figure 93. Address: 0x22, Reset: 0x00, Name: CH_UR_STATUS](ad4858/figures/ad4858-f094.png)

*Figure 93. Address: 0x22, Reset: 0x00, Name: CH_UR_STATUS*

**Table 39. Bit Descriptions for CH_UR_STATUS** ([table-38-p62-register.csv](ad4858/tables/table-38-p62-register.csv), p. 62)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | CH7_UR_FLAG | Channel 7 Underrange Flag. This flag is set to 1 when a conversion result on Channel 7 exceeds the underrange limit set in the CH7_UR register. | 0x0 | R/W1C |
| 6 | CH6_UR_FLAG | Channel 6 Underrange Flag. This flag is set to 1 when a conversion result on Channel 6 exceeds the underrange limit set in the CH6_UR register. | 0x0 | R/W1C |
| 5 | CH5_UR_FLAG | Channel 5 Underrange Flag. This flag is set to 1 when a conversion result on Channel 5 exceeds the underrange limit set in the CH5_UR register. | 0x0 | R/W1C |
| 4 | CH4_UR_FLAG | Channel 4 Underrange Flag. This flag is set to 1 when a conversion result on Channel 4 exceeds the underrange limit set in the CH4_UR register. | 0x0 | R/W1C |
| 3 | CH3_UR_FLAG | Channel 3 Underrange Flag. This flag is set to 1 when a conversion result on Channel 3 exceeds the underrange limit set in the CH3_UR register. | 0x0 | R/W1C |
| 2 | CH2_UR_FLAG | Channel 2 Underrange Flag. This flag is set to 1 when a conversion result on Channel 2 exceeds the underrange limit set in the CH2_UR register. | 0x0 | R/W1C |
| 1 | CH1_UR_FLAG | Channel 1 Underrange Flag. This flag is set to 1 when a conversion result on Channel 1 exceeds the underrange limit set in the CH1_UR register. | 0x0 | R/W1C |
| 0 | CH0_UR_FLAG | Channel 0 Underrange Flag. This flag is set to 1 when a conversion result on Channel 0 exceeds the underrange limit set in the CH0_UR register. | 0x0 | R/W1C |

### REGISTER MAP CRC
<!-- page: 62 -->

![Figure 94. Address: 0x23 to Address: 0x24, Reset: 0x0000, Name: REGMAP_CRC](ad4858/figures/ad4858-f095.png)

*Figure 94. Address: 0x23 to Address: 0x24, Reset: 0x0000, Name: REGMAP_CRC*

### Table 40. Bit Descriptions for REGMAP\_CRC
<!-- page: 63 -->

**Table 40. Bit Descriptions for REGMAP_CRC** ([table-39-p63-register.csv](ad4858/tables/table-39-p63-register.csv), p. 63)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [15:0] | REGMAP_CRC | Register Map CRC. User-calculated CRC checksum covering Address 0xB9 down to 0x25. May be used to continually monitor the state of the AD4858 register map for potential corruption due to alpha particles, system supply glitches, etc. The following CRC polynomial is used to calculate the checksums: x^{16} + x^{14} + x^{13} + x^{12} + x^{10} + x^{8} + x^{6} + x^{4} + x^{3} + x + 1 where the initial value for the CRC calculation is 0xFFFF. | 0x0 | R/W |

### DEVICE CONTROL REGISTER
<!-- page: 63 -->

![Figure 95. Address: 0x25, Reset: 0x11, Name: DEVICE_CTRL](ad4858/figures/ad4858-f096.png)

*Figure 95. Address: 0x25, Reset: 0x11, Name: DEVICE_CTRL*

**Table 41. Bit Descriptions for DEVICE_CTRL** ([table-40-p63-register.csv](ad4858/tables/table-40-p63-register.csv), p. 63)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | TEST_CRCS | Test CRC Engines. Set to 1 while running conversions to introduce a simulated bit error into the FUSE CRC and REGMAP CRC engines. To validate CRC engine functionality verify both FUSE_CRC_FLAG and REGMAP_CRC_FLAG in the DEVICE_STATUS register are set to 1. | 0x0 | R/W |
| [6:5] | RESERVED | Reserved. | 0x0 | R |
| 4 | LVDS_TERM | LVDS Termination Enable. Set to 1 to enable the internal termination resistor on LVDS input pairs. | 0x1 | R/W |
| 3 | LVDS_HALF_BIAS | LVDS Half-Bias Enable. Set to 1 to enable half-bias output drive mode on LVDS output pairs. | 0x0 | R/W |
| 2 | REFBUF_PD | Reference Buffer Power Down. Set to 1 to power down the internal reference buffer. When powered down, an external reference can be connected to the REFBUF pin as shown in Figure 58. | 0x0 | R/W |
| 1 | REF_SEL | Reference Selection. Select whether to use an external or internal reference 0: Internal Reference. Enables the internal reference. 1: External Reference. Powers down the internal reference. Connect an external reference on the REFIO pin, as shown in Figure 57. | 0x0 | R/W |
| 0 | SCKO_ECHO | SCKO Echo Enable. Set to 1 to enable SCKO echoing of SCKI signal. | 0x1 | R/W |

- **Note 0:** Internal Reference. Enables the internal reference.
- **Note 1:** External Reference. Powers down the internal reference. Connect an external reference on the REFIO pin, as shown in the Figure 57. SCKO Echo Enable. Set to 1 to enable SCKO echoing of SCKI signal.

Table 41. Bit Descriptions for DEVICE\_CTRL

### PACKET FORMAT REGISTER
<!-- page: 64 -->

![Figure 96. Address: 0x26, Reset: 0x01, Name: PACKET](ad4858/figures/ad4858-f097.png)

*Figure 96. Address: 0x26, Reset: 0x01, Name: PACKET*

**Table 42. Bit Descriptions for PACKET** ([table-41-p64-register.csv](ad4858/tables/table-41-p64-register.csv), p. 64)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:3] | RESERVED | Reserved. | 0x0 | R |
| 2 | TEST_PAT | Test Pattern Enable. Set to 1 to enable test pattern output data. When enabled, normal conversion data output packets are replaced with fixed data defined by the upper bits of each channels CHx_TESTPAT register (see Test Pattern Packet Format). Use this functionality to validate CMOS or LVDS conversion data output bus communication. | 0x0 | R/W |
| [1:0] | PACKET_SIZE | Packet Size. Selects between 20-bit, 24-bit, or 32-bit packet sizes on the CMOS or LVDS conversion data output bus. Packet data formatting for each packet size depends on whether the AD4858 is operating in non-oversampling or oversampling mode, and whether test pattern data output is enabled (see Packet Format and Test Pattern Packet Format). 00: 20-bit packet size. 01: 24-bit packet size. 10: 32-bit packet size. 11: 32-bit packet size. | 0x1 | R/W |

### OVERSAMPLE CONTROL REGISTER
<!-- page: 64 -->

![Figure 97. Address: 0x27, Reset: 0x00, Name: OVERSAMPLE](ad4858/figures/ad4858-f098.png)

*Figure 97. Address: 0x27, Reset: 0x00, Name: OVERSAMPLE*

**Table 43. Bit Descriptions for OVERSAMPLE** ([table-42-p64-register.csv](ad4858/tables/table-42-p64-register.csv), p. 64)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | OS_EN | Oversample Enable. Selects between oversampling and non-oversampling mode (see Oversampling Mode). 0: Oversampling disabled. Disable oversampling before changing oversampling ratio. 1: Oversampling enabled. | 0x0 | R/W |
| [6:4] | RESERVED | Reserved. | 0x0 | R |
| [3:0] | OS_RATIO | Oversampling Ratio. When oversampling is enabled, selects the number of conversion results to be digitally averaged for each channel (see Oversampling Mode). | 0x0 | R/W |
|  |  | 0000: Average 2 conversions results. |  |  |
|  |  | 0001: Average 4 conversions results. |  |  |
|  |  | 0010: Average 8 conversions results. |  |  |
|  |  | 0011: Average 16 conversions results. |  |  |
|  |  | 0100: Average 32 conversions results. |  |  |
|  |  | 0101: Average 64 conversions results. |  |  |
|  |  | 0110: Average 128 conversions results. |  |  |
|  |  | 0111: Average 256 conversions results. |  |  |
|  |  | 1000: Average 512 conversions results. |  |  |
|  |  | 1001: Average 1024 conversions results. |  |  |
|  |  | 1010: Average 2048 conversions results. |  |  |
|  |  | 1011: Average 4096 conversions results. |  |  |
|  |  | 1100: Average 8192 conversions results. |  |  |
|  |  | 1101: Average 16384 conversions results. |  |  |
|  |  | 1110: Average 32768 conversions results. |  |  |
|  |  | 1111: Average 65536 conversions results. |  |  |

- **Note 0:** Oversampling disabled. Disable oversampling before changing oversampling ratio.

### SEAMLESS HIGH DYNAMIC RANGE REGISTER
<!-- page: 65 -->

![Figure 98. Address: 0x28, Reset: 0xFF, Name: SEAMLESS_HDR](ad4858/figures/ad4858-f099.png)

*Figure 98. Address: 0x28, Reset: 0xFF, Name: SEAMLESS_HDR*

**Table 44. Bit Descriptions for SEAMLESS_HDR** ([table-43-p65-register.csv](ad4858/tables/table-43-p65-register.csv), p. 65)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | CH7_SHDR_EN | Channel 7 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 6 | CH6_SHDR_EN | Channel 6 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 5 | CH5_SHDR_EN | Channel 5 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 4 | CH4_SHDR_EN | Channel 4 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 3 | CH3_SHDR_EN | Channel 3 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 2 | CH2_SHDR_EN | Channel 2 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 1 | CH1_SHDR_EN | Channel 1 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |
| 0 | CH0_SHDR_EN | Channel 0 SHDR Enable. Set to 1 to enable SHDR on this channel. | 0x1 | R/W |

Table 44. Bit Descriptions for SEAMLESS\_HDR

### CHANNEL SLEEP REGISTER
<!-- page: 66 -->

![Figure 99. Address: 0x29, Reset: 0x00, Name: CH_SLEEP](ad4858/figures/ad4858-f100.png)

*Figure 99. Address: 0x29, Reset: 0x00, Name: CH_SLEEP*

**Table 45. Bit Descriptions for CH_SLEEP** ([table-44-p66-register.csv](ad4858/tables/table-44-p66-register.csv), p. 66)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| 7 | CH7_SLEEP | Channel 7 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 6 | CH6_SLEEP | Channel 6 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 5 | CH5_SLEEP | Channel 5 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 4 | CH4_SLEEP | Channel 4 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 3 | CH3_SLEEP | Channel 3 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 2 | CH2_SLEEP | Channel 2 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 1 | CH1_SLEEP | Channel 1 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |
| 0 | CH0_SLEEP | Channel 0 Sleep. Set to 1 to sleep channel, saving power. Channel ignores conversion requests. | 0x0 | R/W |

### CHANNEL 0 SOFTSPAN REGISTER
<!-- page: 66 -->

![Figure 100. Address: 0x2A, Reset: 0x0F, Name: CH0_SOFTSPAN](ad4858/figures/ad4858-f101.png)

*Figure 100. Address: 0x2A, Reset: 0x0F, Name: CH0_SOFTSPAN*

**Table 46. Bit Descriptions for CH0_SOFTSPAN** ([table-45-p66-register.csv](ad4858/tables/table-45-p66-register.csv), p. 66)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [7:4] | RESERVED | Reserved. | 0x0 | R |
| [3:0] | CH0_SOFTSPAN | Channel 0 SoftSpan. Selects the SoftSpan range for this channel (see SoftSpan). 0000: 0 V to 2.5V range. 0001: ±2.5 V range. | 0xF | R/W |
|  |  | 0010: 0 V to 5V range. |  |  |
|  |  | 0011: ±5 V range. |  |  |
|  |  | 0100: 0 V to 6.25 V range. |  |  |
|  |  | 0101: ±6.25 V range. |  |  |
|  |  | 0110: 0 V to 10 V range. |  |  |
|  |  | 0111: ±10 V range. |  |  |
|  |  | 1000: 0 V to 12.5 V range. |  |  |
|  |  | 1001: ±12.5 V range. |  |  |
|  |  | 1010: 0 V to 20 V range. |  |  |
|  |  | 1011: ±20 V range. |  |  |
|  |  | 1100: 0 V to 25 V range. |  |  |
|  |  | 1101: ±25V range. |  |  |
|  |  | 1110: 0 V to 40 V range. |  |  |
|  |  | 1111: ±40 V range. |  |  |

### CHANNEL 0 OFFSET REGISTER
<!-- page: 67 -->

![Figure 101. Address: 0x2B to Address: 0x2D, Reset: 0x000000, Name: CH0_OFFSET](ad4858/figures/ad4858-f102.png)

*Figure 101. Address: 0x2B to Address: 0x2D, Reset: 0x000000, Name: CH0_OFFSET*

**Table 47. Bit Descriptions for CH0_OFFSET** ([table-46-p67-register.csv](ad4858/tables/table-46-p67-register.csv), p. 67)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [23:4] | CH0_OFFSET[19:0] | Channel 0 Offset. 20-bit signed digital offset correction value to be added to every conversion result on this channel (see Digital Offset Correction). Offset default state corresponds to zero offset correction. | 0x0 | R/W |
| [3:0] | RESERVED | Reserved. | 0x0 | R |

### CHANNEL 0 GAIN REGISTER
<!-- page: 67 -->

![Figure 102. Address: 0x2E to Address: 0x2F, Reset: 0x8000, Name: CH0_GAIN](ad4858/figures/ad4858-f103.png)

*Figure 102. Address: 0x2E to Address: 0x2F, Reset: 0x8000, Name: CH0_GAIN*

**Table 48. Bit Descriptions for CH0_GAIN** ([table-47-p67-register.csv](ad4858/tables/table-47-p67-register.csv), p. 67)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [15:0] | CH0_GAIN | Channel 0 Gain. 16-bit unsigned digital gain correction factor to be applied to every conversion result on this channel (see Digital Gain Correction). Default state corresponds to factor of 1.00000. | 0x8000 | R/W |

### CHANNEL 0 PHASE REGISTER
<!-- page: 68 -->

![Figure 103. Address: 0x30 to Address: 0x31, Reset: 0x0000, Name: CH0_PHASE](ad4858/figures/ad4858-f104.png)

*Figure 103. Address: 0x30 to Address: 0x31, Reset: 0x0000, Name: CH0_PHASE*

**Table 49. Bit Descriptions for CH0_PHASE** ([table-48-p68-register.csv](ad4858/tables/table-48-p68-register.csv), p. 68)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [15:0] | CH0_PHASE | Channel 0 Phase. 16-bit unsigned phase correction term to be applied to this channel. This register is only relevant when operating in Oversampling Mode (see Oversampling Mode and Digital Phase Correction) | 0x0 | R/W |

### CHANNEL 0 OVERRANGE LIMIT REGISTER
<!-- page: 68 -->

![Figure 104. Address: 0x32 to Address 0x34, Reset: 0x7FFFF0, Name: CH0_OR](ad4858/figures/ad4858-f105.png)

*Figure 104. Address: 0x32 to Address 0x34, Reset: 0x7FFFF0, Name: CH0_OR*

**Table 50. Bit Descriptions for CH0_OR** ([table-49-p68-register.csv](ad4858/tables/table-49-p68-register.csv), p. 68)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [23:4] | CH0_OR[19:0] | Channel 0 Overrange Limit. If any conversion result on Channel 0 is larger than this 20-bit signed digital overrange threshold value, CH0_OR_FLAG in the Channel Overrange Status Register is set to 1. | 0x7FFFF | R/W |
| [3:0] | RESERVED | Reserved. | 0x0 | R |

### Table 50. Bit Descriptions for CH0\_OR
<!-- page: 68 -->

### CHANNEL 0 UNDERRANGE LIMIT REGISTER
<!-- page: 68 -->

![Figure 105. Address: 0x35 to Address 0x37, Reset: 0x800000, Name: CH0_UR](ad4858/figures/ad4858-f106.png)

*Figure 105. Address: 0x35 to Address 0x37, Reset: 0x800000, Name: CH0_UR*

**Table 51. Bit Descriptions for CH0_UR** ([table-50-p68-register.csv](ad4858/tables/table-50-p68-register.csv), p. 68)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [23:4] | CH0_UR[19:0] | Channel 0 Underrange Limit. If any conversion result on Channel 0 is less than this 20-bit signed digital underrange threshold value, CH0_UR_FLAG in the Channel Underrange Status Register is set to 1. | 0x80000 | R/W |
| [3:0] | RESERVED | Reserved. | 0x0 | R |

### CHANNEL 0 TEST PATTERN REGISTER
<!-- page: 69 -->

**Table 52. Bit Descriptions for CH0_TESTPAT** ([table-51-p69-register.csv](ad4858/tables/table-51-p69-register.csv), p. 69)

| Bits | Bit Name | Description | Reset | Access |
|---|---|---|---|---|
| [31:0] | CH0_TESTPAT | Channel 0 Test Pattern. When the test pattern output is enabled (see Test Pattern Packet Format), the normal conversion data output packets for channel 0 are replaced with fixed data defined by CH0_TESTPAT. The reset state of the most-significant nibble of the CHx_TESTPAT registers corresponds to the numerical value of the channel (that is, 0x0 for Channel 0, 0x1 for Channel 1, … ). | 0xACE3C2A | R/W |

### OUTLINE DIMENSIONS
<!-- page: 70 -->

![Figure 107. 64-Ball BGA Package 7 mm × 7 mm × 1.42 mm (05-08-7086) Dimensions shown in millimeters](ad4858/figures/ad4858-f108.png)

*Figure 107. 64-Ball BGA Package 7 mm × 7 mm × 1.42 mm (05-08-7086) Dimensions shown in millimeters*

### ORDERING GUIDE
<!-- page: 70 -->

| Model[^1]          | Temperature Range   | Package Description   | Packing Quantity   | Package Option   |
|------------------|---------------------|-----------------------|--------------------|------------------|
| AD4858BBCZ       | -40°C to +125°C     | CHIP SCALE BGA        | Tray, 416          | 05-08-7086       |
| AD4858BBCZ-RL-13 | -40°C to +125°C     | CHIP SCALE BGA        | Reel, 2000         | 05-08-7086       |

### EVALUATION BOARD
<!-- page: 70 -->

**Evaluation Board** ([table-53-p70-data.csv](ad4858/tables/table-53-p70-data.csv), p. 70)

| Model[^1] | Description |
|---|---|
| EVAL-AD4858FMCZ | Evaluation Board |

- **Note 1:** Z = RoHS Compliant Part.

