Test Results of setup of adc drivers and AD7982

All Drivers

Circuit Setup for ADA4899-1 to drive AD7982

Setup Description

The test setup for the ADC and ADC input driver amplifiers consists of the EVAL-AD7982SDZ ADC Evaluation board connected to the EVAL-SDP-CB1Z system demonstration platform (SDP) board. An Audio Precision model AP2722, audio analyzer with a low pass output filter was used to generate the ADC driver input signals. Amplifiers to be tested were installed in the Evaluation board and configured as shown in the individual ADC/amplifier driver schematics. The SDP board was used to capture and send the ADC output data to the PC via the USB connection. Please refer to the individual schematics, and corresponding data graphs for additional information regarding the evaluation board configuration, power supplies, signal frequencies, signal amplitudes and testing details.

Parts Used

Part # Category Description
AD8031 Operational Amplifiers (Op Amps) 2.7 V, 800 µA, 80 MHz Rail-to-Rail I/O Single Amplifier
ADR435 Voltage References Ultralow Noise XFET® 5.0V Voltage Reference w/Current Sink and Source Capability
AD7982 Analog to Digital Converters 18-Bit, 1 MSPS PulSAR® 7.0 mW ADC in MSOP/QFN
ADA4899-1 Operational Amplifiers (Op Amps) Unity-Gain Stable, Ultralow Distortion, 1 nV/√Hz Voltage Noise, High Speed Op Amp

Hardware

Part # Category Description
EVAL-AD7982 Evaluation Board Evaluation kit for the AD7982, 18-Bit, 1 MSPS PulSAR® 7.0 mW ADC in MSOP/QFN
SDP-B Evaluation Board Controller board for use with ADI component evaluation boards

Graph of Results and Table of Calculated Performance Values

Tested to 1 kHz

ADA4841-1 driving AD7982

Setup Description

The test setup for the ADC and ADC input driver amplifiers consists of the EVAL-AD7982SDZ ADC Evaluation board connected to the EVAL-SDP-CB1Z system demonstration platform (SDP) board. An Audio Precision model AP2722, audio analyzer with a low pass output filter was used to generate the ADC driver input signals. Amplifiers to be tested were installed in the Evaluation board and configured as shown in the individual ADC/amplifier driver schematics. The SDP board was used to capture and send the ADC output data to the PC via the USB connection. Please refer to the individual schematics, and corresponding data graphs for additional information regarding the evaluation board configuration, power supplies, signal frequencies, signal amplitudes and testing details.

Parts Used

Part # Category Description
AD8031 Operational Amplifiers (Op Amps) 2.7 V, 800 µA, 80 MHz Rail-to-Rail I/O Single Amplifier
ADR435 Voltage References Ultralow Noise XFET® 5.0V Voltage Reference w/Current Sink and Source Capability
AD7982 Analog to Digital Converters 18-Bit, 1 MSPS PulSAR® 7.0 mW ADC in MSOP/QFN
ADA4841-1 Operational Amplifiers (Op Amps) Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier

Hardware

Part # Category Description
EVAL-AD7982 Evaluation Board Evaluation kit for the AD7982, 18-Bit, 1 MSPS PulSAR® 7.0 mW ADC in MSOP/QFN
SDP-B Evaluation Board Controller board for use with ADI component evaluation boards

Graph of Results and Table of Calculated Performance Values

Tested at 1 kHz

Circuit Setup for ADA4627-1 to drive AD7982

Setup Description

The test setup for the ADC and ADC input driver amplifiers consists of the EVAL-AD7982SDZ ADC Evaluation board connected to the EVAL-SDP-CB1Z system demonstration platform (SDP) board. An Audio Precision model AP2722, audio analyzer with a low pass output filter was used to generate the ADC driver input signals. Amplifiers to be tested were installed in the Evaluation board and configured as shown in the individual ADC/amplifier driver schematics. The SDP board was used to capture and send the ADC output data to the PC via the USB connection. Please refer to the individual schematics, and corresponding data graphs for additional information regarding the evaluation board configuration, power supplies, signal frequencies, signal amplitudes and testing details.

Parts Used

Part # Category Description
AD8031 Operational Amplifiers (Op Amps) 2.7 V, 800 µA, 80 MHz Rail-to-Rail I/O Single Amplifier
ADR435 Voltage References Ultralow Noise XFET® 5.0V Voltage Reference w/Current Sink and Source Capability
AD7982 Analog to Digital Converters 18-Bit, 1 MSPS PulSAR® 7.0 mW ADC in MSOP/QFN
ADA4627-1 High Supply Voltage Amplifiers (>=+12V) 36 V, 19 MHz, Low Noise, Low Bias Current, JFET Op Amp

Hardware

Part # Category Description
EVAL-AD7982 Evaluation Board Evaluation kit for the AD7982, 18-Bit, 1 MSPS PulSAR® 7.0 mW ADC in MSOP/QFN
SDP-B Evaluation Board Controller board for use with ADI component evaluation boards

Graph of Results and Table of Calculated Performance Values

Tested at 100 Hz
沪ICP备09046653号
Send Feedback X
content here.
content here.

Send Feedback

Close