Wide Dynamic Range, High Speed, Digitally Controlled VGA
The ADL5202 is a digitally controlled, variable gain, wide bandwidth amplifier that provides precise gain control, high output IP3, and low noise figure. The excellent distortion performance and high signal bandwidth make the ADL5202 an excellent gain control device for a variety of receiver applications. The ADL5202 also incorporates a low power mode option that lowers the supply current.
For wide input dynamic range applications, the ADL5202 provides a broad 31.5 dB gain range with 0.5 dB resolution. The gain is adjustable through multiple gain control interface options: parallel, serial peripheral interface, and up/down.
Incorporating proprietary distortion cancellation techniques, the ADL5202 achieves a better than 47.5 dBm output IP3 at frequencies approaching 200 MHz for most gain settings.
The ADL5202 is powered on by applying the appropriate logic level to the PWUPx pins. The quiescent current of the ADL5202 is typically 160 mA in low power mode. When configured in high performance mode for more demanding applications, the quiescent current is 210 mA. When powered down, the ADL5202 consumes less than 14 mA and offers excellent input-to-output isolation. The gain setting is preserved during power-down.
Fabricated on an Analog Devices, Inc., high speed SiGe process, the ADL5202 provides precise gain adjustment capabilities with good distortion performance and low phase error. The ADL5202 amplifier comes in a compact, thermally enhanced 40-lead, 6 mm × 6 mm LFCSP package and operates over a temperature range of −40°C to +85°C.
- Differential ADC drivers
- High IF sampling receivers
- High output power IF amplification
This product has been released to the market. The data sheet contains all final specifications and operating conditions. For new designs, ADI recommends utilization of these products.
ADL5202-EVALZ is a fully populated, 4-layer, FR4-based evaluation board. For normal operation, it require a 5 V power supply capable of delivering 500 mA and a 3.3 V power supply capable of delivering 1 mA. The 5 V supply is connected to the test loops labeled VPOS and GND. This is the bias for the main amplifiers. The open collector outputs are connected to the main bias via the power plane. The 3.3 V supply is connected to the test loops labeled 3.3 V and GND. The RF input is applied to the SMA connectors labeled INA- and INB-. The RF output is available at the SMA connector labeled OUTA- and OUTB-. A fully differential input and output is easily configured by removing R8, R9, R79, R80, installing a zero ohm jumper at R81, R82, R88, R89, removing transformers, T1, T2, T3, T4 and placing jumpers across the transformer pads. The evaluation board can be programmed through the USB port of a PC running Windows XP or Vista with Microsoft .NET Framework 3.5 installed. The required control software can be downloaded from www.analog.com. Manual operation of the gain control functions is possible using the 3 pin headers and supplied jumpers. Power up is controlled using the 3 pin header labeled PWUPA and PWUPB or an external control signal maybe applied using the SMA connectors labeled PWUPA and PWUPB.
Product Selection Guide
RF Source Booklet
RF IC Product Overview
ADI has always placed the highest emphasis on delivering products that meet the maximum levels of quality and reliability. We achieve this by incorporating quality and reliability checks in every scope of product and process design, and in the manufacturing process as well. "Zero defects" for shipped products is always our goal.
The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Analog Devices, Inc. sales office or authorized distributor. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing.