High Performance, Low Power, ISM Band FSK/GFSK/MSK/GMSK Transceiver IC
The ADF7023-J is a very low power, high performance, highly integrated 2FSK/GFSK/MSK/GMSK transceiver designed for operation in the 902 MHz to 958 MHz frequency band, which covers the ARIB Standard T96 band at 950 MHz. Data rates from 1 kbps to 300 kbps are supported.
The transmit RF synthesizer contains a VCO and a low noise fractional-N phase locked loop (PLL) with an output channel frequency resolution of 400 Hz. The VCO operates at twice the fundamental frequency to reduce spurious emissions. The receive and transmit synthesizer bandwidths are automatically, and independently, configured to achieve optimum phase noise, modulation quality, and settling time. The transmitter output power is programmable from −20 dBm to +13.5 dBm, with automatic PA ramping to meet transient spurious specifications. The part possesses both single-ended and differential PAs, which allow for Tx antenna diversity.
The receiver is exceptionally linear, achieving an IP3 specification of −12.2 dBm and −11.5 dBm at maximum gain and minimum gain, respectively, and an IP2 specification of 18.5 dBm and 27 dBm at maximum gain and minimum gain, respectively. The receiver achieves an interference blocking specification of 66 dB at a ±2 MHz offset and 74 dB at a ±10 MHz offset. Thus, the part is extremely resilient to the presence of interferers in spectrally noisy environments. The receiver features a novel, high speed, AFC loop, allowing the PLL to find and correct any RF frequency errors in the recovered packet. A patent pending image rejection calibration scheme is available by downloading the image rejection calibration firmware module to program RAM. The algorithm does not require the use of an external RF source nor does it require any user intervention once initiated. The results of the calibration can be stored in nonvolatile memory for use on subsequent power-ups of the transceiver.
See data sheet for additional information.
- Smart metering
- IEEE 802.15.4g
- Home automation
- Process and building control
- Home Energy Management Systems (HEMS)
- Wireless sensor networks (WSNs)
- Wireless healthcare
This product has been released to the market. The data sheet contains all final specifications and operating conditions. For new designs, ADI recommends utilization of these products.
This page contains ordering information for the evaluation board used to evaluate the ADF7023-J High Performance, Low Power, ISM Band FSK/GFSK/MSK/GMSK Transceiver IC.
Product Selection Guide
RF Source Booklet
RF IC Product Overview
Solutions Bulletins & Brochures
RF Transceivers for Short Range Devices
The ADF7000 series of transmitter and transceiver ICs provides high performance, robust, short range wireless...
Design, Simulate, and Document Proprietary Wireless Systems
The broad acceptance of standards developed for short range wireless connectivity has been one of the notable...
Third Party Partner Program
Short Range Transceivers Third Party Developers
The ADF701x Series of Transmitters and ADF702x Series of Transceivers from ADI are suitable for automatic meter...
Low Power, Low Cost, Wireless ECG Holter Monitor
Wireless Technologies for Smart Meters: Focus on Water Metering
RF Meets Power Lines: Designing Intelligent Smart Grid Systems that Promote...
RF DesignLine, March 2010
Smart Metering Technology Promotes Energy Efficiency for a Greener World
The metering of electric power coming into the home is going electronic, replacing the long-established...
Wireless Short Range Devices and Narrowband Communications
The term “Short Range Device” (SRD) covers radio transmitters which provide either unidirectional or bi-directional...
Understand Wireless Short-Range Devices for Global License-Free Systems
Short-range devices (SRD) are radio transmitters that communicate unidirectionally or bidirectionally with little...
ADI has always placed the highest emphasis on delivering products that meet the maximum levels of quality and reliability. We achieve this by incorporating quality and reliability checks in every scope of product and process design, and in the manufacturing process as well. "Zero defects" for shipped products is always our goal.
Didn't find what you were looking for?
The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Analog Devices, Inc. sales office or authorized distributor. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing.