ADN4662

Single, 3 V, CMOS, LVDS Differential Line Receiver
Manufactured by:

Product Details

The ADN4662 is a single, CMOS, low voltage differential signaling (LVDS) line receiver offering data rates of over 400 Mbps (200 MHz), and ultralow power consumption. It features a flow-through pinout for easy PCB layout and separation of input and output signals.

The device accepts low voltage (310 mV typical) differential input signals and converts them to a single-ended 3 V TTL/ CMOS logic level. The ADN4662 and its companion driver, the ADN4661, offer a new solution to high speed, point-to-point data transmission, and a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL).
Applications

  • Point-to-point data transmission
  • Multidrop buses
  • Clock distribution networks
  • Backplane receivers
  • Product Lifecycle

    checked Production

    At least one model within this product family is in production and available for purchase. The product is appropriate for new designs but newer alternatives may exist.

    Evaluation Kits

    X +

    EVAL-FMCMOTCON2 Circuit Diagram

    Product Details

    The AD-FMCMOTCON2-EBZ is a complete high performance servo system on an FPGA Mezzanine Card (FMC) board, the purpose of which is to provide a complete motor drive system demonstrating efficient and high dynamic control of three phase PMSM and induction motors up to 48V and 20A.

    Two motors can be driven at the same time, each motor having its separate power supply. The system incorporates high quality power sources; reliable power, control, and feedback signals isolation; accurate measurement of motor current & voltage signals; high speed interfaces for control signals to allow fast controller response; industrial Ethernet high speed interfaces; single ended Hall, differential Hall, encoder and resolver interfaces; digital position sensors interface; flexible control with a FPGA/SoC interface.

    The kit consists of two boards: a controller board and a drive board. An optional AD-DYNO2-EBZ dynamometer can also be purchased through Avnet and is intended to be an extension of the drive system.

    Controller Board

    • Digital board for interfacing with the low and high voltage drive boards
    • Compatible with all Xilinx FPGA platforms with FMC LPC or HPC connectors
    • FMC signals voltage adaptation interface for seamless operation on all FMC voltage levels
    • Fully isolated digital control and feedback signals
    • Isolated Xilinx XADC interface
    • 2 x Gbit Ethernet PHYs for high speed industrial communication, with 3rd party EtherCAT support
    • Single ended Hall, Differential Hall, Encoder, Resolver interfaces
    • Digital sensors interfaces
      • EnDat
      • BISS Interface

    Drive Board

    • Drives motors up to 48V @ 20A
    • Drives 2 motors simultaneously
    • High frequency drive stage implemented with ADI isolated gate drivers
    • Supported motor types
      BLDC
      PMSM
      Brushed DC
      Stepper (bipolar / unipolar)
    • Integrated over current protection
    • Reverse voltage protection
    • Current and Voltage measurement using isolated ADCs
    • BEMF zero cross detection for sensorless control of PMSM or BLDC motors
    • Separate voltage supplies for the 2 motors so that the motors don't influence each other

    Dynamometer System with Embedded Control

    • Two BLDC motors connected by a rigid couple in a dyno setup, which can be used to test real-time motor control performance.
    • One BLDC motor acts as an electronically adjustable load and is driven by the embedded control system. This motor can be directly connected to the FMC motor drive to get complex / active loads. The load can be driven also by the AD-FMCMOTCON2-EBZ to implement dynamic load profiles.
    • The other BLDC motor is driven by the FMC motor drive.
    • Measurement and display of load motor current
    • Measurement and display of load motor speed
    • External control using Analog Discovery and MathWorks Instrumentation Control Toolbox

    Software:

    Example reference designs showing how to use the platform with Xilinx® FPGAs or SoCs and high performance control algorithms from Mathworks® are provided together with the hardware. Information on the FMC board, and how to use it, the design package that surrounds it, and the software which can make it work, can be found by clicking the software link.

    Tools & Simulations

    X +

    IBIS Models

    Design Resources

    X +

    ADI has always placed the highest emphasis on delivering products that meet the maximum levels of quality and reliability. We achieve this by incorporating quality and reliability checks in every scope of product and process design, and in the manufacturing process as well.  "Zero defects" for shipped products is always our goal.

    ADN4662 Material Declaration
    PCN-PDN Information Quality And Reliability Symbols and Footprints

    Discussions

    X+

    Didn't find what you were looking for?

    Sample & Buy

    X+
    Back
    Check Inventory

    The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Analog Devices, Inc. sales office or authorized distributor. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing.


    Price Table Help

     
    Evaluation Boards Pricing displayed is based on 1-piece.
    Pricing displayed is based on 1-piece. The USA list pricing shown is for budgetary use only, shown in United States dollars (FOB USA per unit), and is subject to change. International prices may vary due to local duties, taxes, fees and exchange rates.