18-Bit, 2 MSPS Precision, Differential SAR ADC
The AD4003/AD4007/AD4011 are low noise, low power, high speed, 18-bit, precision successive approximation register (SAR) analog-to-digital converters (ADCs). The AD4003, AD4007, and AD4011 offer 2 MSPS, 1 MSPS, and 500 kSPS throughputs, respectively. They incorporate ease of use features that reduce signal chain power consumption, reduce signal chain complexity, and enable higher channel density. The high-Z mode, coupled with a long acquisition phase, eliminates the need for a dedicated high power, high speed ADC driver, thus broadening the range of low power precision amplifiers that can drive these ADCs directly while still achieving optimum performance. The input span compression feature enables the ADC driver amplifier and the ADC to operate off common supply rails without the need for a negative supply while preserving the full ADC code range. The low serial peripheral interface (SPI) clock rate requirement reduces the digital input/output power consumption, broadens processor options, and simplifies the task of sending data across digital isolation. Operating from a 1.8 V supply, the AD4003/AD4007/AD4011 have a ±VREF fully differential input range with VREF ranging from 2.4 V to 5.1 V. The AD4003 consumes only 16 mW at 2 MSPS with a minimum SCK rate of 75 MHz in turbo mode, the AD4007 consumes only 8 mW at 1 MSPS, and the AD4011 consumes only 4 mW at 500 kSPS. The AD4003/AD4007/AD4011 all achieve ±1.0 LSB integral nonlinearty error (INL) maximum, guaranteed no missing codes at 18 bits with 100.5 dB typical signal-to-noise ratio (SNR) for 1 kHz inputs. The reference voltage is applied externally and can be set independently of the supply voltage. The SPI-compatible versatile serial interface features seven different modes including the ability, using the SDI input, to daisy-chain several ADCs on a single 3-wire bus and provides an optional busy indicator. The AD4003/AD4007/AD4011 are compatible with 1.8 V, 2.5 V, 3 V, and 5 V logic, using the separate VIO supply. The AD4003/AD4007 are available in a 10-lead MSOP and LFCSP, and the AD4011 is available in a 10-lead LFCSP, with operation specified from −40°C to +125°C. The devices are pin compatible with the 16-bit, 2 MSPS AD4000
- Automatic test equipment
- Machine automation
- Medical equipment
- Battery-powered equipment
- Precision data acquisition systems
This product has been released to the market. The data sheet contains all final specifications and operating conditions. For new designs, ADI recommends utilization of these products.
The EVAL-AD4000FMCZ / EVAL-AD4001FMCZ / EVAL-AD4003FMCZ / EVAL-AD4020FMCZ evaluation boards are ideal for use with the Analog Devices, Inc., high speed system demonstration platform (EVAL-SDP-CH1Z). These evaluation boards interface to the SDP-H1 board via a 120-pin connector. SMA connectors, JP2 and JP3, are provided for the low noise analog signal source.
On-board components include a high precision buffered band gap 5.0 V reference (the ADR4550), a reference buffer (the ADA4807-1), a common-mode buffer (the ADA4807-1), a signal conditioning circuit with two op amps (the ADA4807-1), and a power supply to derive the necessary voltage levels to supply all voltage needs.
The EVAL-AD4000FMCZ, EVAL-AD4001FMCZ, and EVAL-AD4003FMCZ are populated with the AD4000, AD4001, and AD4003, respectively. However, these boards can be used to evaluate the performance of the AD4004, AD4005, AD4007, AD4008, and AD4011 by limiting the sample rate in the evaluation software to the maximum sample rate of the specific ADC. For example, the AD4000 on the EVAL-AD4000FMCZ can be used to evaluate the performance of the AD4004 if the sample rate is limited to 1 MSPS. See the data sheet of each product for its corresponding evaluation board.
Recommended Driver Amplifiers
- For precision, lowest power applications: ADA4096-2, ADA4692-2, ADA4077-1, ADA4084-1.
- For high frequency, low noise, low distortion applications: ADA4897-1, ADA4932-1.
- For low input bias current, low noise applications: ADA4610-1.
- For precision, low power, low distortion applications: ADA4807-1, ADA4940-1.
Recommended External Voltage References
Recommended Digital Isolators
ADI has always placed the highest emphasis on delivering products that meet the maximum levels of quality and reliability. We achieve this by incorporating quality and reliability checks in every scope of product and process design, and in the manufacturing process as well. "Zero defects" for shipped products is always our goal.
The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Analog Devices, Inc. sales office or authorized distributor. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing.