-
Products
- Amplifiers and Comparators
- Analog Microcontrollers
- Analog to Digital Converters
- Audio/Video Products
- Broadband Products
- Clock and Timing
- Digital to Analog Converters
- Embedded Processing and DSP
- Fiber/Optic
- Interface
- MEMS
- Power Management
- References
- RF/IF Components
- Sensors
- Switches/Multiplexers
- Temperature Sensing and Thermal Management
- Other Products
- Analog/HDMI/DVI Interfaces
- Audio A/D Converters
- Audio Amplifiers
- Audio CODECs
- Audio D/A Converters
- Audio Signal Processors
- Camera/Camcorder Analog Front Ends
- Display Driver Electronics
- iMEMS® Microphone
- Lens Driver Components
- Mobile TV Tuners
- Sample Rate Converters
- Video Amps/Buffers/Filters
- Video CODECs
- Video Compression
- Video Decoders
- Video Encoders
OTHERS WAYS
TO FIND PRODUCTSSelection Guides Product Selection Tables - Resources & Tools
-
About ADI
- My Analog
-
AD8343 S-Parameters
(htm, 35 kB)
The S2P file provides differential impedance measurements. The S2P port assignments are as follows:
- Port 1: differential input
- Port 2: differential output
In most cases the 2-port data will be all you'll need to develop matching networks for the AD8343. LO port can be considered as a 50 ohm input. - AD8353 S-Parameters (zip, 35 kB)
- AD8354 S-Parameters (zip, 35 kB)
- AD8362 S-Parameters (zip, 14 kB)
- ADL5320 S-Parameters (zip, 21 kB)
- ADL5321 S Parameters (zip, 0)
- ADL5322 S-Parameters (zip, 32 kB)
- ADL5323 S-Parameters (zip, 32 kB)
- ADL5390: Class S Parameters (zip, 151 kB)
- ADL5391 S-Parameters (zip, 309 kB)
- ADL5521 S Parameters (zip, 651 kB)
- ADL5523 S Parameters (zip, 0)
- ADL5530 S-Parameters (zip, 10 kB)
- ADL5531 S-Parameters (zip, 10 kB)
- ADL5534 S-Parameters Rev A (zip, 23 kB)
- ADL5541 S-Parameters (zip, 43 kB)
- ADL5542 S-Parameters (zip, 43 kB)
- ADL5601 S Parameters (zip, 31 kB)
- ADL5602 S Parameters (zip, 31 kB)
-
dBm/dBu/dBv Calculator
This calculator converts between standard units of power measurement and signal strength. -
Impedance Matching Tutorial
This tutorial examines the Smith Chart and its application to transmission line impedance matching. -
Power Dissipation vs Die Temp
This tool estimates die temperature and power dissipation based on the supply voltages, ambient temperature, load characteristics, and package thermal data. -
RF Impedance Matching Tool
This calculator matches a known complex load to a desired impedance at a given frequency. Computes component values and displays a sample circuit of the matching network. -
Settling Time Calculator
This calculator estimates settling time for a multiplexer by calculating the time constant of a cascaded RC network. In addition, it displays the settling time for four levels of accuracy expressed in %FS and bits. -
Sigma-Delta ADC Tutorial
An interactive illustration showing the behavior of an idealized sigma-delta A/D converter. -
SNR/THD/SINAD Calculator
This calculator converts SNR, THD, and SINAD into ENOBs and noise. It also computes one of SNR, THD, or SINAD from the other two. -
VRMS / dBm / dBu / dBV calculator
A utility to convert between standard units of power measurement and signal strength.