Application Notes (3)
Circuit Note (3)
- CN-0190: Robust, Multivoltage, High Efficiency, 25 W Universal Power Supply Module with 6 V to 14 V Input (pdf, 357 kB)
- CN-0193: High Voltage (30 V) DAC Powered from a Low Voltage (3 V) Supply Generates Tuning Signals for Antennas and Filters (pdf, 173 kB)
- CN0201: Complete 5 V, Single-Supply, 8-Channel Multiplexed Data Acquisition System with PGIA for Industrial Signal Levels (pdf, 263 kB)
Technical Articles (1)
ADIsim Design/Simulation Tools (2)
-
ADIsimPower™ Voltage Regulator Design Tool
This expert design tool produces custom DC-DC converter designs in about a minute. The user enters 5 inputs and chooses to optimize for efficiency, PCB space, cost, or part count. Output is a complete schematic, BOM, efficiency plot, and performance summary. A PDF summary and a blank PCB is offered for each design to facilitate fast prototyping to verify the design. -
Download files for ADIsimPower™ Voltage Regulator Design Tool
The individual Excel-based voltage regulator design tools used in ADIsimPower™.
Data Sheets (2)
Design & Integration Files (1)
-
CN0193 Design & Integration Files
(zip, 189 kB)
- Schematic
- Bill of Materials
- Gerber Files
- PAD Files
- Assembly Drawing
Device Drivers (1)
Documentation (3)
-
ADIsimPower™ Voltage Regulator Design Tool
This expert design tool produces custom DC-DC converter designs in about a minute. The user enters 5 inputs and chooses to optimize for efficiency, PCB space, cost, or part count. Output is a complete schematic, BOM, efficiency plot, and performance summary. A PDF summary and a blank PCB is offered for each design to facilitate fast prototyping to verify the design. - EVAL-ADP1612/ADP1613: 650 kHz/1.3 MHz Step-Up Converter (pdf, 198 kB)
- UG-059: Evaluation Board User Guide for AD5501/AD5504 (pdf, 544 kB)
Power Reference Designs (9)
-
ADP1613 3.3 Vin, 200 Vout at 2 mA
(pdf, 348 kB)
This design uses a boost converter with quadrupler charge pump. It utilizes an innovative 4 stage charge pump to increase the output voltage of the boost stage by a factor of 4. -
ADP1613 50mA Iout SEPIC-Cuk
(pdf, 411 kB)
Cascoded coupled SEPIC-Cuk converter producing clean ± 9 V rails from a 12V input. -
ADP1613 50mA Iout SEPIC-Cuk
(pdf, 411 kB)
Cascoded coupled SEPIC-Cuk converter producing clean ± 9 V rails from a 12V input. -
ADP1613 Coupled SEPIC converter
(pdf, 88 kB)
Coupled SEPIC converter which converts a 3 -5 V input to a clean 5 V output with very low ripple noise. -
ADP1613 Isolated Flyback Converter; Input +30-
(pdf, 311 kB)
30 - 60V input isolated flyback converter with a "cascode" MOSFET. It uses primary side regulation to avoid the power consumption of a feedback optocoupler. -
ADP1613 SEPIC Converter Vin 30-60 Vout 3.3V 150mA
(pdf, 118 kB)
Cascode SEPIC converter which produces 3.3V output at 0 - 150 mA. -
PRD1209: ±10 Vout from 24 Vin at 100 mA
(pdf, 0)
A SEPIC-Cuk converter used to create a dual rail output from a single input voltage. -
PRD1210: ±15 Vout from 24 Vin at 80 mA
(pdf, 375 kB)
A SEPIC-Cuk converter is used to create a dual rail output from a single input voltage. -
PRD1211: 5.0 Vin, 200 Vout at 2mA
(pdf, 329 kB)
A boost converter with quadrupler charge pump. It utilizes an innovative 4 stage charge pump to increase the output voltage of the boost stage by a factor of 4. This enable us to use a very inexpensive integrated FET boost controller. The power draw was tested at 33 mA with no load.
Software and Tools (1)
- AD5501/AD5504 Evaluation Software, Rev. 1.07 (zip, 4245 kB)
Solutions Bulletins (2)
User Guides (1)
- UG-059: Evaluation Board User Guide for AD5501/AD5504 (pdf, 544 kB)
Webcasts (1)
-
Isolating Power in Communication Bus and Gate Drive Applications
Starting with a communications application overview of small power options through the process of selecting the right power products this webcast is a great resource for your communications applications designs.
Analog Dialogue (1)
-
Boost Supply and High-Voltage DAC Provide Tuning Signal for Antennas and Filters
Analog Dialogue, Volume 44-12 Back Burner, December 2010
